Quadra-Fire 31ST-ACC-AU Owner`s manual

Tested and
Listed by
3100 WOOD STOVE SERIES
Automatic Combustion Control (ACC)
Owner’s Manual
Portland
Oregon USA
O-T L
C
US
OMNI-Test Laboratories, Inc.
Installation and Operation
MODELS:
31M-ACC-MBK
Millennium Model
31ST-ACC
Step Top Uni-Body Model
31M-ACC-LE
Limited Edition
(Pedestal Model Shown)
WARNING
WARNING
If the information in these instructions is not followed exactly, a
fire may result causing property
damage, personal injury, or death.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.
• Do not overfire - If heater or chimney connector glows, you are overfiring. Overfiring
will void your warranty.
• Comply with all minimum clearances to
combustibles as specified. Failure to
comply may cause house fire.
Installation and service of this appliance should
be performed by qualified personnel. Hearth &
Home Technologies recommends NFI certified
professionals, or technicians supervised by an NFI
certified professional.
HOT SURFACES!
Glass and other surfaces are
hot during operation AND cool
down.
Hot glass will cause burns.
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same
room as fireplace.
• Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or
other flammable materials.
• Keep clothing, furniture, draperies and other
flammable materials away.
NOTE
WARNING
To obtain a French translation of this manual, please contact
your dealer or visit www.quadrafire.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrafire.com
00
www.quadrafire.com
7033-277J
Fire Risk.
For use with solid wood fuel only.
Other fuels may overfire and generate poisonous
gases (i.e. carbon monoxide).
September 9, 2014
R
3100 Wood Stove Series (ACC)
and Welcome to the Quadra-Fire Family!
Hearth & Home Technologies welcomes you to our tradition of excellence! In choosing a Quadra-Fire appliance,
you have our assurance of commitment to quality, durability, and performance.
our stoves, inserts and fireplaces. And yet we are old-fashioned when it comes to craftsmanship. Each unit is meticulously fabricated and surfaces are hand-finished for lasting
beauty and enjoyment. Our pledge to quality is completed
as each model undergoes a quality control inspection.
This commitment begins with our research of the market,
including ‘Voice of the Customer’ contacts, ensuring we
make products that will satisfy your needs. Our Research
and Development facility then employs the world’s most
advanced technology to achieve the optimum operation of
We wish you and your family many years of enjoyment in
the warmth and comfort of your hearth appliance. Thank
you for choosing Quadra-Fire.
NOTE: Clearances may only be reduced
by means approved by the regulatory
authority having jurisdiction
SAMPLE OF SERIAL NUMBER / SAFETY LABEL
LOCATION: BACK OF APPLIANCE
WHILE IN OPERATION DO NOT TOUCH, KEEP CHILDREN AND CLOTHING AWAY. CONTACT MAY CAUSE SKIN BURNS.
CAUTION: HOT
FURNISHINGS AND OTHER COMBUSTIBLE MATERIAL FAR AWAY FROM THE APPLIANCE. SEE NAMEPLATE AND INSTRUCTIONS.
KEEP
CHAUD LORS DE L'OPÉRATION. NE PAS TOUCHER. GARDEZ LES ENFANTS ET LES VÊTEMENTS LOIN DE L'ESPACE DÉSIGNÉ DE L'INSTALLATION. LE CONTACT PEUT CAUSER DES
ATTENTION:BRÛLURES À LA PEAU. GARDEZ LES MEUBLES ET LES MATÉRIAUX COMBUSTIBLES LOIN DE L'ESPACE DÉSIGNÉ DE L'APPAREIL. VOIR L'ÉTIQUETTE ET LES INSTRUCTIONS.
LISTED ROOM HEATER, SOLID FUEL TYPE.
ALSO FOR USE IN MOBILE HOMES. (UM) 84
HUD . "For Use with Solid Wood Fuel Only"
APPAREIL DE CHAUFFAGE DE PIÈCE, DE TYPE DE
COMBUSTIBLE SOLIDE, POUR USAGE DANS LES
MAISONS MOBILES. (UM) 84 HUD. "Pour Usage Avec
Bois Solide Seulement"
PRÉVENTION DES FEUX DE MAISON
PREVENT HOUSE FIRES
Install and use only in accordance with
manufacturer's installation and operating
instructions. Contact local building or fire
officials about restrictions and installation
inspections in your area. Do not obstruct the
space beneath heater.
WARNING - For Mobile Homes: Do not
install in a sleeping room. An outside
combustion air inlet must be provided and
unrestricted while unit is in use. The
structural integrity of the mobile home floor,
ceiling and walls must be maintained. The
stove needs to be properly grounded to the
frame of the mobile home. Components
required for mobile home installation:
Outside Air Kit, Part Number OAK-ACC..
Refer to manufacturer's instructions and
local codes for precautions required for
passing chimney through a combustible
wall or ceiling and maximum offsets.
Inspect and clean chimney frequently Under Certain Conditions of Use, Creosote
Buildup May Occur Rapidly.
Do not connect this unit to a chimney
serving another appliance.
Optional Blower, Part BK-ACC.
Electrical Rating: 115 VAC, 1.2 Amps, 60 Hz.
Route power cord away from unit. Do not
route cord under or in front of appliance.
DANGER: Risk of electrical shock.
Disconnect power supply before servicing.
Replace glass only with 5mm ceramic
available from your dealer.
Do not use grate or elevate fire. Build
wood fire directly on hearth.
Do not overfire - if heater or chimney
connector glows, you are overfiring.
Operate only with the fuel loading door
closed. Open only to add fuel to the fire.
FLOOR PROTECTION:
Floor protector for Millennium and Pedestal Step Top Models
must be a 3/8 inch min. thickness, non-combustible material or
equivalent, (Step Top Leg Model only must be 1/2 inch [13mm]
min thickness, “k” value 0.84, R value 0.59 or non-combustible
floor protector 1-1/4 inch [32mm] thick) extending beneath
heater and to front/sides/rear as indicated on the diagram
below. Exception: Non-combustible floor protections must
extend beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side.
Installez et utilisez en accord avec les instructions
d'installation et d'opération du fabricant. Contactez le
bureau de la construction ou le bureau des incendies au
sujet des restrictions et des inspections d'installation dans
votre voisinage. Ne pas obstruez l'espace en dessous de
l'appareil.
AVIS - Pour Les Maisons Mobiles: Ne pas installer dans
une chambre à coucher. Un tuyau extérieur de combustion
d'air doit être installé et ne doit pas être obstrué lorsque
l'appareil est en usage. La structure intégrale du plancher,
du plafond et des murs de la maison mobile doit être
maintenue intacte. L'appareil de chauffage doit être fixé à
la charpente de la maison mobile. Les composants requis
pour l'installation des maisons mobiles: Assemblage d'air
extérieur, Numéro de Pièce OAK-ACC.
Référez vous aux instructions du fabricant et des codes
locaux pour les précautions requises pour passer une
cheminée à travers un mur ou un plafond combustibles, et
les compensations maximums.
Inspectez et nettoyez la cheminée fréquemment. Sous
certaines conditions, il se peut que la créosote s'accumule
rapidement.
Ne pas connecter cet appareil à une cheminée servant un autre
appareil.
tVentilateur Optionnel, Pièce BK-ACC.
Puissance Électrique: 115 VAC, 1.2 Amps, 60 Hz.
Éloignez le fil électrique de l'appareil. Ne pas faire passer
le fil électrique au dessus ou en dessous de l'appareil.
DANGER: Il y a risque de décharge électrique.
Déconnectez le fil électrique de la prise de contact avant
le service.
Remplacez la vitre seulement avec une vitre céramique de
5 mm disponible chez votre fournisseur.
N'élevez pas le feu. Bâtissez le feu de bois directement
sur l'âtre.
Ne pas surchauffer. Si l'appareil de chauffage ou le tuyau
de cheminée rougissent, vous surchauffez.
Opérez l'appareil seulement lorsque la porte de
chargement est fermée. Ouvrez la porte seulement
lorsque vous devez ajouter des combustibles dans le feu.
Tested and
Listed by
3100 ACC Series
US
007
TESTED TO:/ TESTÉ À:
UL 1482-11 , ULC S627-00.
Report / Rapport
#061-S-66-6
VENT SPECIFICATIONS:
SINGLE WALL: Six inch (6 inches) (152mm) diameter, minimum 24 MSG black or
blued steel connector pipe, with a listed factory-built UL103HT* Class "A" chimney,
suitable for use with solid fuels, or a masonry chimney, and the referenced
clearances.
DOUBLE WALL: Six inch (6 inches) (152mm) diameter, listed double wall air
insulated connector pipe with listed factory-built UL103HT* Class "A" chimney, or a
masonry chimney and the referenced clearances
MOBILE HOME: Use double wall pipe by Dura-Vent DVL, Selkirk Metalbestos DS or
Security DL double wall connector pipe. Must be equipped with a spark arrestor.
Apply double wall clearances below when installing unit.
SPÉCIFICATIONS DE LA VENTILATION:
MUR SIMPLE: De six (6 inches) (152mm) de diamètre le connecteur de conduit de
minimum d'acier noir ou bleu de minimum de 24MSG, avec une cheminée bâtit en
usine UL103HT* de Classe "A", adéquate pour usage avec les combustions solides,
ou une cheminée de briques, avec espaces libres référés.
MUR DOUBLE: De six (6 inches) (152mm) de diamètre, le connecteur du conduit
d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT* de Classe
"A:, ou une cheminée de briques, avec espaces libres alloués.
MAISON MOBILE: Utiliser un conduit de mur double par Dura-Vent DVL, Selkirk
Metalbestos DS ou Security DL. Doit être équipé d'un arrêt d'étincelle. Utiliser les
espaces libres pour mur double comme mentionné ci-bas.
E
L
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS: In Inches & (Millimeters)
NOTE: All "A" , "C" and "F" Dimensions are to inside diameter of the flue collar.
SINGLE WALL PIPE
Flat Top Model
Step Top Model
DOUBLE WALL PIPE
Flat Top Model
Step Top Model
A
P
ESPACES LIBRES MINIMUM DES MATÉRIAUX COMBUSTIBLES:En Pouces & (millimètres)
C
D
E
F
H
48 (1220)
48 (1220)
12 (305)
12 (305)
Modèle au dessus en appartement
Modèle au dessus en escalier
CONDUIT DU MUR DOUBLE
10.5 (267) 6.5 (165) 22 (559)
10 (254) 6 (152) 20.5 (521)
48 (1220)
48 (1220)
9 (229)
9 (229)
Modèle au dessus en appartement
Modèle au dessus en escalier
13 (330) 6.5 (165) 15.5 (394)
11 (279) 4 (102) 13 (330)
Fuel loading door
16" from glass
12 (305)
10 (254)
8.5 (216) 22 (559)
6 (152) 20.5 (521)
13 (330) 8 (203) 17 (432)
11 (279) 5.5 (140) 14.5 (368)
48 (1220)
48 (1220)
8 (203)
10 (254)
4.5 (114) 17.5 (445) 8.5 (216) 6.5 (165) 15.5 (394)
6 (152) 20.5 (521) 11 (279) 4 (102) 13 (330)
48 (1220)
48 (1220)
9 (229) Modèle au dessus en appartement
9 (229) Modèle au dessus en escalier
USA
Millennium & Step Top 31-5/8" Min
Manufactured by:
Fabriqué par:
www.quadrafire.com
Page 2
203mm
(8")
Millennium
1280mm
(50-3/8")
minimum
Step Top
1321mm
(52")
minimum
E
F
E
CONDUIT DU MUR DOUBLE
11.75 (298) 8.25 (210) 23.5 (597) 14.5 (368)
10 (254) 6 (152) 20.5 (521) 11 (279)
N/A
N/A
N/A
N/A
F
* Modèle au dessus en appartement
* Modèle au dessus en escalier
48 (1220)
48 (1220)
*In Canada must comply with Standard CAN/ULC-S629-M87 for the 650oC Factory-built chimney.
*Au Canada doit conformer a CAN/ULC-S629-M87 la norme pour 650oC cheminée bâtit en usine.
ALCOVE SIDE VIEW /
VUE DE CÔTÉ DE L'ALCÔVE
* SEE PIPE MANUFACTURERS CLEARANCES - NOT TESTED / VOIR LE FABRICANT POUR LES ESPACES LIBRES DES CONDUIT - PAS TESTÉ
90o OFF TOP
UP & OUT CEILING CLEARANCE
ESPACE LIBRE DU DESSUS DE
L'APPAREIL AU PLAFOND AVEC 90
DE COURBURE
H*
G
H*
G
G
A
B
STOVE TO CEILING CLEARANCE
ESPACE LIBRE DU POÊLE AU
PLAFOND
CANADA
A
ALCOVE TOP VIEW /
VUE DU HAUT DE L'ALCÔVE
C
457mm (18")
B
D
1040mm (41") minimum
Made in U.S.A. of US and
imported parts.
1445 N. Highway, Colville, WA 99114
CORNER INSTALLATION
INSTALLATION DU COIN
G
203mm
(8")
8"
C
D
INSTALLATION: ALCOVE - Six inch (6 inches) (152mm) diameter listed DOUBLE WALL air insulated connector pipe with UL103 HT* listed factory-built Class "A" chimney, or a masonry
chimney. (Mobile Home must be equipped with a spark arrestor.) Maximum depth of Alcove shall be no more than 48 inches (1220mm) with a minimum height of 48 inches (1220mm) to top of
unit, and the referenced clearances.
INSTALLATION: ALCÔVE - De six (6 inches) (152mm) de diamètre, le connecteur du conduit d'air isolé pour mur double avec une cheminée bâtit en usine UL103HT de Classe "A", ou une
cheminée de briques. (Les maisons mobiles doivent être équipées d'un arrêt d'étincelle). La profondeur maximum de l'alcôve ne doit pas être de plus de 48 inches (1220mm) avec une hauteur
minimum de 48 inches (1220mm) du haut de l'appareil, et des espaces libres alloués.
DOUBLE WALL PIPE
Flat Top Model
Step Top Model
Test Lab &
Report No.
B
CONDUIT DU MUR SIMPLE
12 (305) Modèle au dessus en appartement
12 (305) Modèle au dessus en escalier
CONDUIT DU MUR DOUBLE
203mm (8")
Millennium
& Step Top
39-5/8”
minimum
A
INSTALLATION: 90o ELBOW OFF TOP OF STOVE THROUGH BACKWALL
INSTALLATION: 90o DU COURBURE AU DESSUS DE HAUT DU POÊLE A TRAVERS LE MUR ARRIÈRE
SINGLE WALL PIPE
Flat Top Model
Step Top Model
DOUBLE WALL PIPE
Flat Top Model
Step Top Model
Model
Name
BACKWALL/SIDEWALL
MUR ARRIÈRE/MUR DE CÔTÉ
CONDUIT DU MUR SIMPLE
G
15.25 (387) 11.75 (298) 25.5 (648) 16 (406) 8 (203) 17 (432)
12 (305) 8.5 (216) 22 (559) 12.5 (318) 5.5 (140) 14.5 (368)
M
B
Serial No.
NOTE: Toutes les dimensions "A", "C", et "F" sont à partir du diamètre intérieur de l'entrée du conduit.
INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH MINIMUM 2 FOOT VERTICAL OFF STOVE TOP
INSTALLATION: ENTIÈREMENT VERTICALE OU HORIZONTALE AVEC 609mm VERTICAL MINIMUM DU HAUT DU POÊLE
A
S
PROTECTION DU PLANCHER:
Le protecteur de plancher doit être (Modèles Millennium et au
dessus en escalier socle) d'un minimum de 3/8 inch (9.5 mm)
d'épaisseur, de matériel incombustible ou équivalent, (Modèle au
dessus en escalier pied d’un minimum de 1/2 inch [13mm]
d'épaisseur, “k” =0.84, R value 0.59 au le protecteur de
plancher de matériel incombustible 1-1/4 inch [32mm]
d’épaisseur). s'étendant du dessous de l'appareil de chauffage
à l'avant, aux cotés et à l'arrière comme indiqué sur le
diagramme suivant. Exception: Les protections incombustibles
du plancher doivent s'étendre en dessous du conduit de
cheminée lorsqu'installées avec une ventilation à l'horizontale et
s'étendre de 2 inches (51mm) de chaque côté.
SERIAL NO. / NUMÉRO DE SÉRIE
R
Portland
Oregon USA
O-T L
C
OMNI-Test Laboratories, Inc.
Fabriqué aux
États-Unis-d’Amérique par des
pièces d’origine américaine et
pièces importées.
2014
2015 2016 Jan. Feb. Mar. Apr. May June July Aug. Sept. Oct. Nov. Dec.
U.S. ENVIRONMENTAL PROTECTION AGENCY - Certified to
comply with July 1990 particulate emission standards.
Mfg. Date
7033-278F
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER L'ÉTIQUETTE
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
Safety Alert Key:
•
DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
•
WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
•
CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
•
NOTICE: Indicates practices which may cause damage to the fireplace or to property.
TABLE OF CONTENTS
Section 1: Listing and Code Approvals
A.
B.
C.
D.
Section 8: Operating Instructions
Appliance Certifications ......................4
Mobile Home Approved ......................4
Glass Specifications ............................4
BTU & Efficiency Specifications ..........4
A.
B.
C.
D.
E.
F.
G.
H.
I.
J.
K.
Section 2: Getting Started
A. Design, Installation & Location
Considerations ....................................5
B. Fire Safety ..........................................5
C. Negative Pressure ..............................6
D. Flue Draft Considerations ...................7
E. Venting Systems .................................7
F. Tools and Supplies Needed................7
G. Inspect Appliance & Components.......7
H. Typical Stove System .........................8
Over-Firing Your Appliance .................26
Wood Selection & Storage ..................26
Burning Process ..................................26-27
Automatic Combustion Control (ACC) ....27
Air Controls .........................................27-28
Burn Rates & Operating Efficiency .....28
Baffle & Blanket Placement ................29
Building A Fire .....................................30
Blower Operating Instructions .............31
Opacity (Smoke) .................................31
Frequently Asked Questions...............31
Section 9: Maintaining & Servicing Appliance
A.
B.
C.
D.
E.
F.
G.
Section 3: Dimensions & Clearances
A. Appliance Dimensions ........................9-10
B. Clearances to Combustibles ...............11
Quick Reference Maintenance Guide .32
General Maintenance & Cleaning .......33-34
Glass Replacement .............................34-35
Firebrick Replacement ........................35
Baffle Removal ....................................36
Snap Disc Replacement .....................36
Tube Channel Replacement ...............37
Section 4: Installation Consideration
A.
B.
C.
D.
E.
Hearth Requirements .........................12-13
Alternate Floor Protection Calculation 14
Outside Air ..........................................14-15
Blower Installation ...............................16
Blower Speed Adjustment ..................16
Section 10: Troubleshooting ........................38
Section 11: Reference Material
Section 5: Chimney Requirements
A.
B.
C.
D.
E.
Venting Components ..........................17
Chimney Systems ...............................17-19
Installing Chimney Components .........19
Chimney Termination Requirements ..20
2-10-03 Rule ........................................20
A. Exploded Drawing & Service Parts3100 Millennium..................................39-43
B. Exploded Drawing & Service Parts3100 Step Top ....................................44-48
C. Exploded Drawing & Service Parts3100 Limited Edition ...........................49-53
D. Warranty Policy...................................54-55
E. Contact Information ............................56
Section 6: Mobile Home ...............................21
Section 7: Appliance Set-Up
A. Pedestal & Ash Removal System
(ARS) Installation ...............................22-23
B. Leg Kit & Ash Removal System
(ARS) Installation ................................23-24
C. Door Handle Assembly .......................24
D. Decorative Tile Installation..................24-25
September 9, 2014
7033-277J
Page 3
R
3100 Wood Stove Series (ACC)
1
Listing and Code Approvals
D. BTU & Efficiency Specifications
A. Appliance Certification
Model:
3100 Millennium, 3100 Limited Edition
& Step Top Uni-Body (ACC)
Laboratory:
EPA Certified:
1.1 grams per hour
OMNI Test Laboratories, Inc.
EPA Certification
Number and Date:
Number: 649
Issued: 2011
Report No:
061-S-66-6
Efficiency:
78.7%
Type:
Listed Room Heater, Solid Fuel Type
Standard:
UL1482-11 and ULC S627-00
and (UM) 84-HUD, Mobile Home
Approved.
The Quadra-Fire 3100 Series Wood Stove (ACC) meets the
U.S. Environmental Protection Agency’s 1990 particulate
emission standards.
EPA: 11,800 to 32,000
BTU Output:
Vent Size:
6 inches
Firebox Size:
1.85 cubic feet
Max Wood Length:
20 inches
Fuel:
Cord Wood
B. Mobile Home Approved
This appliance is approved for mobile home installations
when not installed in a sleeping room and when an outside
combustion air inlet is provided. The structural integrity of
the mobile home floor, ceiling, and walls must be maintained.
The appliance must be properly grounded to the frame of
the mobile home and use only listed double-wall connector
pipe. Outside Air Kit, part OAK-ACC must be installed in a
mobile home installation
C. Glass Specifications
This stove is equipped with 5mm ceramic glass. Replace
glass only with 5mm ceramic glass. Please contact your
dealer for replacement glass.
NOTE: This installation must conform with local codes. In the
absence of local codes you must comply with the UL1482-11,
(UM) 84-HUD and NPFA211 in the U.S.A. and the ULC S627-00
and CAN/CSA-B365 Installation Codes in Canada.
Peak: 51,100 continuous
loading
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved
by Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with
unit).
• Do NOT Overfire - If appliance or chimney connector glows,
you are overfiring.
Any such action that may cause a fire hazard.
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
NOTE: CANADA ONLY! The 31M-ACC-LE model, per
ULC S627-00 fuel cannot be stored in lower pedestal
area
Quadra-Fire is a registered trademark of Hearth & Home
Technologies.
Page 4
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
2
Getting Started
A. Design, Installation & Location Considerations
B. Fire Safety
Consideration must be given to:
To provide reasonable fire safety, the following should be
given serious consideration:
•
•
•
•
Safety
Convenience
Traffic flow
Chimney and chimney connector required
It is a good idea to plan your installation on paper, using exact
measurements for clearances and floor protection, before
actually beginning the installation. If you are not using an
existing chimney, place the appliance where there will be a
clear passage for a factory-built listed chimney through the
ceiling and roof.
We recommend that a qualified building inspector and your
insurance company representative review your plans before
and after installation
1.
Install at least one smoke detector on each floor of
your home to ensure your safety. They should be
located away from the heating appliance and close
to the sleeping areas. Follow the smoke detector
manufacturer’s placement and installation instructions,
and be sure to maintain regularly.
2.
A conveniently located Class A fire extinguisher
to contend with small fires resulting from burning
embers.
3.
A practiced evacuation plan, consisting of at least two
escape routes.
4.
A plan to deal with a chimney fire as follows:
If this appliance is in an area where children may be near it
is recommended that you purchase a decorative barrier to go
in front of the appliance. Remember to always keep children
away while it is operating and do not let anyone operate
this appliance unless they are familiar with these operating
instructions.
In the event of a chimney fire:
a
b.
Evacuate the house immediately
Notify fire department
WARNING
NOTE: Service Space
In order to replace the tube channel a clearance of 19
inches (483mm) is required on the right side of stove in
order to remove the tubes with the stove in place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement. See page 37.
Fire Risk.
•
Do not operate appliance before reading and
understanding operating instructions.
•
Failure to operate appliance properly may
cause a house fire.
WARNING
CAUTION
Asphyxiation Risk.
Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building, fire officials or
authorities having jurisdiction about restrictions, installation
inspection, and permits.
September 9, 2014
7033-277J
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
May allow flue gases to enter the house.
Page 5
R
3100 Wood Stove Series (ACC)
C. Negative Pressure
Draft is the pressure difference needed to vent appliances
successfully. Considerations for successful draft include:
•
Preventing negative pressure
•
Location of appliance and chimney
To minimize the affects of negative air pressure the following
must be considered:
Negative pressure results from the imbalance of air available for the stove to operate properly. Causes for this imbalance include:
•
Exhaust fans (kitchen, bath) etc.)
•
Range hoods
•
Combustion air requirements for furnaces, water
heaters and other combustion appliances
•
Clothes dryers
•
Location of return-air vents to furnace or air conditioning
•
Imbalances of HVAC air handling system
•
Upper level air leaks
•
Recessed lighting
•
Attic hatch opening
•
Duct leaks
•
Install the outside air kit. Install the intake on the
side of the house towards prevailing winds during the
heating season.
•
Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.
•
Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appliance,
•
Avoid installing the appliance near doors, walkways
or small isolated spaces.
•
Recessed lighting should be of “sealed can” design;
attic hatches weather stripped or sealed; and attic
mounted duct work and air handler joints and seams
taped or sealed.
WARNING
Asphyxiation Risk.
• Negative pressure can cause spillage of combustion fumes, soot and carbon monoxide.
• Appliance needs to draft properly for safety.
Recommended
Location
Recommended
Location
Marginal
Location
Location
Not
Recommended
Location NOT
Recommended
Windward
Outside Air Kit Termination Cap
Leeward
Multi-level Roofs
Figure 6.1
Page 6
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
D. Flue Draft Considerations
F. Tools And Supplies Needed
Location of the appliance and chimney will affect performance. As shown in Figure 6.1 on page 6 the chimney
should:
Before beginning the installation be sure that the following
tools and building supplies are available.
•
Be installed through the warm space enclosed by the
building envelope. This helps to produce more draft,
especially during lighting and die down of the fire.
•
Penetrate the highest part of the roof. This minimizes
the affects of wind turbulence and down drafts.
•
Consider the appliance location in order to avoid
floor and ceiling attic joists and rafters.
Exterior conditions such as roof line, surrounding trees,
prevailing winds and nearby hills can influence stove
performance. Your local dealer is the expert in your geographic
area and can usually make suggestions or discover solutions
that will easily correct your flue problem.
To be sure that your appliance burns properly, the chimney
draft (static pressure) should be approximately -.04 inch water
column (W.C.) during a low burn and -.10 inch W.C. during a
high burn, measured 6 inches (152mm) above the top of the
appliance after one hour of operation at each burn setting.
NOTE: These are guidelines only, and may vary somewhat
for individual installations.
E. Venting Systems
The venting system consists of a chimney connector (also
known as stove pipe) and a chimney. These get extremely
hot during use. Temperatures inside the chimney may
exceed 2000F (1100C) in the event of a creosote fire. To
protect against the possibility of a house fire, the chimney
connector and chimney must be properly installed and
maintained.
An approved thimble must be used when a connection is
made through a combustible wall to a chimney. A chimney
support package must be used when a connection is made
through the ceiling to a prefabricated chimney. These
accessories are absolutely necessary to provide safe
clearances to combustible wall and ceiling material. Follow
venting manufacturer’s clearances when installing venting
system.
Reciprocating saw
Pliers
Hammer
Phillips Head Screwdriver
Flat Blade Screwdriver
Plumb Line
Level
Tape Measure
Framing Material
Hi-Temp Caulking Material
Gloves
Framing Square
Electric Drill & Bits (1/4”)
Safety Glasses
1/2 in. - 3/4 in. length, #6 or
#8 self drilling screws (need 3
per pipe section connection)
G. Inspect Appliance & Components and
Pre-Use Check List
1.
Place the appliance in a location near the final
installation area and follow the procedures below:
2.
Open the appliance and remove all the parts and
articles packed inside the Component Pack. Inspect
all the parts and glass for shipping damage. Contact
your dealer if any irregularities are noticed.
3.
All safety warnings have been read and followed.
4.
This Owner’s Manual has been read.
5.
Floor protection requirements have been met.
6.
Venting is properly installed.
7.
The proper clearances from the appliance and chimney to combustible materials have been met.
8.
The masonry chimney is inspected by a professional
and is clean, or the factory built metal chimney is
installed according to the manufacturer’s instructions and clearances.
9.
The chimney meets the required minimum height.
10.
All labels have been removed from the glass door.
11.
Plated surfaces have been wiped clean, if applicable
12.
A power outlet is available nearby if installing
optional blower assembly.
WARNING
WARNING
Fire Risk.
Inspect appliance and components for damage.
Damaged parts may impair safe operation.
Asphyxiation Risk.
• Do NOT connect this unit to a chimney flue
servicing another appliance.
• Do NOT connect to any air distribution duct
or system.
May allow flue gases to enter the house.
• Do NOT install damaged components.
• Do NOT install incomplete components.
• Do NOT install substitute components.
Report damaged parts to dealer.
September 9, 2014
7033-277J
Page 7
R
3100 Wood Stove Series (ACC)
H. Typical Stove Systems
Stove system with masonry chimney consists of:
• Stove
• Chimney Connector (stove pipe)
• Thimble
• Masonry Chimney
• Hearth Pad Floor Protection
Figure 8.1 Masonry Chimney
Stove system with prefabricated
metal chimney consists of:
• Stove
• Chimney Connector
(stove pipe)
Listed Termination Cap
Storm Collar
Listed Termination Cap
Flashing
Roof Brace (if required)
• Thimble (for exterior
chimney)
Storm Collar
Flashing
Listed Chimney
• Firestops
• Insulations Shields
• Storm Collar and Flashing
Trim Collar on
Inside Wall
• Termination Cap
• Hearth Pad Floor Protection
Chimney
Connector
Listed Chimney
Insulated " T "
Wall Support
Ceiling Support
Chimney
Connector
Thimble
Floor
Protector
Floor
Protector
Figure 8.2 Exterior Prefabricated Chimney
Page 8
7033-277J
Figure 8.3 Interior Prefabricated Chimney
September 9, 2014
R
3100 Wood Stove Series (ACC)
3
Dimensions and Clearances
A. Appliance Dimensions
NOTE: Flue Collar size is 6 inch (152mm) diameter (ID)
31M-ACC-MBK (Millennium Model
26-11/16 in. (668mm)
25 1/4 in. (641mm)
24-5/16 in. (618mm)
6-11/16 in.
(170mm)
CL
9-15/16 in.
(237mm)
12-1/2 in.
(318mm)
CL
10-15/16 in.
15-1/16 in. (271mm)
(383mm)
30 in.
(762mm)
11-1/2 in.
(292mm)
14-15/16 in.
(373mm)
19-1/16 in.
(484mm)
16 in. (406mm)
CL
4-1/2 in
(108mm)
Outside Air
Connection
20-3/4 in. (527mm)
Figure 9.2 Front View
Figure 9.1 Side View
31M-ACC-LE (Limited Edition Model)
26-11/16 (677mm)
25-1/4 (641mm)
24-5/16 (618mm)
12-5/8 (320mm)
6-11/16 170mm)
10-15/16
(278mm)
15-1/16 (383mm)
14-15/16
(379mm)
19-1/16 (484mm)
38-1/2
(978mm)
20
(508mm)
15-1/4
(387mm)
21-1/2 (564mm)
Figure 9.3
September 9, 2014
17-7/8 (454mm)
Figure 9.4
7033-277J
Page 9
R
3100 Wood Stove Series (ACC)
Appliance Dimensions (Cont.)
31ST-ACC (Step Top Model with
Pedestal)
31ST-ACC (Step Top Model with
Queen Ann Legs)
25 in. (635mm)
9-5/16 in.
(237mm)
CL
12-1/2 in.
(318mm)
14-15/16 in.
(379mm)
19-1/16 in.
(484mm)
33-1/8 in.
(841mm)
10-15/16 in.
(278mm)
15-1/16 in.
(383mm)
34-1/4 in.
(870mm)
18 in.
(457mm)
23-7/8 in.
(606mm)
Figure 10.1
Figure 10.3
26-11/16 in.(678mm)
6-11/16 in.
(170mm)
24-5/16 in. (618mm)
15-3/8 in. (391mm)
3-11/16 in. (94mm)
CL
3-1/2 in.
(89mm)
10-3/8 in.
(264mm)
16 in. (406mm)
11-1/2 in.
(292mm)
21-1/8 in. (537mm)
20-3/4 in. (527mm)
Figure 10.2
Page 10
Figure 10.4
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
B. Clearances to Combustibles (UL and ULC)
*
CORNER INSTALLATION
BACKWALL / SIDEWALL
STOVE TO CEILING
CLEARANCE
C
A
D
B
C
MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS in inches & (Millimeters)
NOTE: All A, B, and C Dimensions are to the center of the flue collar
A
B
C
D
INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH VERTICAL RISE
SINGLE WALL PIPE - A, B, and C Dimensions are based off of standard 18”
stove pipe clearance to combustible or unit certified clearances,
whichever is greater.
Millennium | Limited Edition Model 18.25 (464)
28.5 (724) 20 (508) 48 (1220)
Step Top Model
15 (381)
25 (635) 17.5 (445) 48 (1220)
ALCOVE SIDE VIEW
DOUBLE WALL PIPE - A, B, and C dimensions are based off of certification
clearances. Stove pipe manufacture clearances MUST be adhered to if they
exceed certified unit clearances.
Millennium | Limited Edition Model
13.5 (343)
25 (635) 18.5 (470) 48 (1220)
Step Top Model
13 (330) 23.5 (597)
16 (406) 48 (1220)
D
A
INSTALLATION: 90° Elbow off top of stove through backwall
SINGLE WALL PIPE
Millennium | Limited Edition Model
Step Top Model
15 (381)
13 (330)
25 (635)
20 (508)
23.5 (597) 17.5 (445)
48 (1220)
48 (1220)
11 (279)
13 (330)
20.5 (521)
23.5 (597)
48 (1220)
48 (1220)
DOUBLE WALL PIPE
Millennium | Limited Edition Model
Step Top Model
18.5(470)
16 (406)
INSTALLATION: ALCOVE
Six inch diameter listed Double wall air insulated connector pipe with UL103 HT
listed factory built Class A chimney or masonry chimney. Maximum depth of
Alcove shall be no more than 48 inches (1220mm) with a minimum height of 48
inches (1220mm) to top of unit and the referenced clearances.
Canada must comply with CAN/ULC-S269 M87 for the 650° factory built chimney
DOUBLE WALL PIPE
Millennium | Limited Edition Model
Step Top Model
14.75 (375)
13 (330)
26.5 (673)
23.5 (597)
N/A
N/A
ALCOVE TOP VIEW
B
48 (1220)
48 (1220)
* FOLLOW PIPE MANUFACTURES CLEARANCES AS REQUIRED
NOTE: Clearances may only be reduced by means
approved by the regulatory authority having jurisdiction
NOTE: Service Space
WARNING
Fire Risk.
• Comply with all minimum clearances to
combustibles as specified.
• Failure to comply may cause house fire.
September 9, 2014
In order to replace the tube channel assembly a clearance
of 19 inches (483mm) is required on the right side of stove in
order to remove the tubes with the stove in place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.
7033-277J
Page 11
R
3100 Wood Stove Series (ACC)
4
Installation
A. Hearth Protection Requirements
FLOOR PROTECTION: Floor protector must be non-combustible material, extending beneath heater and to the front,
sides and rear as indicated. The floor must be non-combustible or otherwise adequately protected from radiant heat
given off by the unit and from sparks and falling embers. A
layer of thin brick or ceramic tile over a combustible floor is
not sufficient.
In Canada, similar floor protection must be provided 18
inches (457mm) in front and 8 inches (203mm) from the
sides and rear of the stove. *See exception.
*EXCEPTION: Non-combustible floor protections must
extend beneath the flue pipe when installed with horizontal
venting and extend 2 inches (51mm) beyond each side.
See Figure 12.2.
WARNING
Fire Risk.
For the Millennium | Limited Edition Models In US installations, it is necessary to install a floor protector of a minimum
of 3/8 inch (9.5mm) thick metal clad millboard or equivalent a
minimum of 16 inches (406mm) in front of glass and 8 inches
(203mm) to both sides of the fuel loading door. Open the
door and measure 8 inches (203mm) from the side edge of
the opening in the face of the appliance. *See exception.
•
Hearth pads must be installed exactly as specified
High temperatures or hot embers may ignite concealed
combustibles.
Corner hearth pad dimensions
with single wall pipe
52-1/2 in.
o
co ptio
ve na
ra l
ge
Millennium | Limited Edition Models
33-1/4 in.
27
-3
/8
39-5/8 in.
minimum
Fuel loading door
in
.
38
-1
5/
16
in
.
3-1/8 in.
4-7/8 in.
.
in
13
5°
/8
-5
60
8 in.
in
in
.
16 in. from glass
/8
-5
31
3-
1/
16
USA
Figure 12.3
31-5/8 in.
minimum
Corner hearth pad dimensions
with double wall pipe
USA
Figure 12.1
51 in.
o
co ptio
ve na
ra l
ge
Must extend 2 in.
(51mm) beyond
each side of pipe
(shaded area)
203mm (8 in.)
31-3/4 in.
in
/2
-1
58
27
-3
/8
in
.
38
-1
5/
16
in
.
1260mm
(49-5/8 in.)
minimum
13
5°
.
203mm
(8 in.)
203mm
(8 in.)
/8
-5
31
in
Figure 12.4
1041mm (41 in.)
minimum
CANADA
Figure 12.2
Page 12
31/
16
in
.
457mm (18 in.)
NOTE: Corner hearth pad dimensions are based off of 18” min. clearance for single wall pipe, 6” min. for double wall pipe, OR unit tested
safety clearances to combustibles whichever is greater.
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
Step-Top Uni-Body Model
For the Step Top Pedestal Model In US installations, it is
necessary to install a floor protector of a minimum of 3/8 inch
(9.5mm) thick metal clad millboard or equivalent a minimum
of 16 inches (406mm) in front of glass and 8 inches (203mm)
to both sides of the fuel loading door. Open the door and
measure 8 inches (203mm) from the side edge of the opening in the face of the appliance. *See page 12 for Canadian
clearances and horizontal venting exception.
For the Step Top Leg Model In US installations, it is necessary to install a floor protector of a minimum thickness of
1-1/4 inch (32mm) or 1/2 inch of “k” value of 0.84 or R value
= 0.59 thick metal clad millboard or equivalent a minimum of
16 inches (406mm) in front of glass and 8 inches (203mm)
to both sides of the fuel loading door. Open the door and
measure 8 inches (203mm) from the side edge of the opening in the face of the appliance. *See page 12 for Canadian
clearances and horizontal venting exception. See Page
24 for calculation for alternate floor protection.
Corner hearth pad dimensions
with single wall pipe
50 in.
3-1/4 in.
13
5°
in
.
27
-5
/1
6
31
-5
/8
38
-1
5/
16
31-5/8 in.
minimum
in
8 in.
in
.
16 in. from glass
57
-1
/8
in
Fuel loading door
30-3/4 in
in
39-5/8 in.
minimum
31/
16
4-3/4 in.
l
na e
io rag
t
op ove
c
USA
Figure 13.1
Figure 13.3
Corner hearth pad dimensions
with double wall pipe
48-1/2 in.
Must extend 2 in.
(51mm) beyond
each side of pipe
(shaded area)
l
na e
io rag
t
op ove
c
in
in
.
27
-5
/1
6
31
-5
/8
38
-
15
/1
6
in
.
55
in
1254mm
(49-3/8 in.)
minimum
13
5°
31/
16
203mm
(8 in.)
203mm
(8 in.)
29 in.
in
203mm (8 in.)
457mm (18 in.)
1041mm (41 in.)
minimum
Figure 13.2
NOTE: •
September 9, 2014
Figure 13.4
CANADA
NOTE: Corner hearth pad dimensions are based off of 18” min. clearance for single wall pipe, 6” min. for double wall pipe, OR unit tested
safety clearances to combustibles whichever is greater.
Illustrations and photos reflect typical installations and are FOR DESIGN PURPOSES ONLY.
•
Illustrations/diagrams are not drawn to scale.
•
Actual installation may vary due to individual design preference
•
Hearth & Home Technologies reserves the right to alter its products.
7033-277J
Page 13
R
3100 Wood Stove Series (ACC)
o
heat resistant material up to 350 F. Cut the pipe to the
required length for your installation.
B. Calculating Alternate Floor Protection Material
Thermal Conductivity: k value
The k value indicates the amount of heat (in BTU’s) that will flow
in 1 hour through 1 square foot of a uniform material 1 inch thick
for each degree (F) of temperature difference from one side of
the material to the other. The LOWER the k factor means less
heat is being conducted through the non-combustible material to
the combustible material beneath it. The k value of a material
must be equal or smaller then the required k value to be acceptable.
(BTU) (inch)
(foot2 (hour) (oF)
• Phillips head screw driver
• Silicone sealant
• Drills and saws necessary for cutting holes through the
wall or flooring in your home.
1. Remove all materials from packing box.
2. Using a #2 Phillips screw driver attach the flex adapter to
the stove using 4 screws. Figure 14.1
Thermal Resistance: R value
3. For floor installations, remove circular” knock-out” in the
base of the pedestal.
The R value is a measure of a material’s resistance to heat transfer. R value is convenient when more than one material is used
since you can add the R values together, whereas you can not
do this for k value. The HIGHER the R factor means less heat
is being conducted through the non-combustible material to the
combustible material beneath it. The R value of a material must
be equal or larger then the required R value to be acceptable.
4. Floor & Rear Installation: Cut a 4 inch (102mm) hole in
outside wall or floor to accommodate outside air piping.
Use 4 inch (102mm) aluminum metal flex or rigid piping
to directly connect outside air to appliance intake. Use
the supplied termination cap with a rodent screen. Seal
between the wall (or floor) and the pipe with silicone to
prevent moisture penetration.
Converting k to R:
5. Floor Installation Alternative: In some instances you
may not be able to install the flex pipe as shown in Figure
14.1. If that is the case, you will need to order SRV7033041 which includes a cover plate and sealing rope as
shown in Figure 14.2. The goal is to seal the pedestal
so no room air can leak into the pedestal or for cold air
infiltration.
Divide 1 by k and multiply the results times the thickness in inches of the material.
R = 1/k x inches of thickness
Converting R to k:
Divide the inches of thickness by R.
k = inches of thickness/R
Calculations:
Flex Adapter
Example: Floor protection requires k value of 0.84 and 3/4 inch
thick.
Wire Tie
Alternative material has a k value of 0.6 and is 3/4 inch thick.
Divide 0.6 by .75 = k value of 0.80. This k value is smaller than
0.84 and therefore is acceptable.
C. Outside Air Kit Installation
Termination
Cap
For Floor Installations Remove
Circular “Knock-Out”
in Base of Pedestal.
Flex Line
Wire Tie
31M-ACC-MBK & 31ST-ACC
A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed
by the fire must be replaced. Air is replaced via air leakage
around windows and under doors. In homes that have tightly
sealed doors and windows, an outside air source is needed.
An optional Outside Air Kit is available.
Included in OAK-ACC: Termination cap, (2) wire ties, flex
Figure 14.1 - Floor & Rear Installation
adapter, and fasteners
Included in SRV7033-041: Cover plate and sealing rope (see
Rope to Seal
Pedestal
Floor Installation Alternative below,
Figure 14.2)
Cover
Plate
Items Needed for Installation (not supplied)
• 4 inch flex aluminum pipe, or if using alternate material,
then it shall be made from durable, non-combustible,
Page 14
Figure 14.2 - Floor Installation Alternative
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
Outside Air Kit Installation (cont.)
WARNING
31M-ACC-LE
A source of air (oxygen) is necessary in order for combustion to take place. Whatever combustion air is consumed
by the fire must be replaced. Air is replaced via air leakage
around windows and under doors. In homes that have tightly
sealed doors and windows, an outside air source is needed.
An optional Outside Air Kit is available.
Included in OAK-ACC: Termination cap, (2) wire ties, flex
Fire Risk.
Asphyxiation Risk.
Do not draw outside combustion air from:
adapter, and fasteners
•
Wall, floor or ceiling cavity
•
Enclosed space such as an attic or garage
•
Close proximity to exhaust vents or chimneys
Fumes or odor may result
Items Needed for Installation (not supplied)
WARNING
• 4 inch flex aluminum pipe, or if using alternate material,
then it shall be made from durable, non-combustible,
heat resistant material up to 350oF. Cut the pipe to the
required length for your installation.
Asphyxiation Risk.
Outside air inlet must be located to prevent blockage
from:
• Phillips head screw driver
•
Leaves
• Silicone sealant
•
Snow or ice
• Drills and saws necessary for cutting holes through the
wall in your home.
•
Other debris
Block may cause combustion air starvation
Smoke spillage may set off alarms or irritate sensitive
individuals.
1. Remove all materials from packing box.
2. Remove six screws holding back plate on back of unit.
Fig. 15.1
WARNING
Asphyxiation Risk.
Length of outside air supply duct shall NOT exceed
the length of the vertical height of the exhaust flue.
• Fire will not burn properly
• Smoke spillage occurs when door is opened due to
air starvation.
3. Remove 4 inch circular “knock-out” by twisting loose using
4 screws supplied. Fig. 15.1
4. Using 4 screws supplied, attach outside air deflector
channel to outside air backplate.
5. Reassemble backplate to unit.
31M-ACC-LE ONLY! Part number 7033-339
is the adapter for the outside air-kit. This part
ships with the unit and must be used with the
OAK-ACC.
Figure 15.1
September 9, 2014
7033-277J
Page 15
R
3100 Wood Stove Series (ACC)
E. Adjusting The Blower Speed Control
D. Blower (Optional)
1. Remove the 3 bolts (1/4”-20 Phillips head) on the outer
skin at the bottom rear of appliance.
2. Align holes in mounting flange of blower with bolt holes in
appliance. Blower should be positioned at bottom of rear
outer skin as shown in Figure 16.1.
3. Re-insert and tighten bolts, securing blower onto outer
wall of appliance.
4. Place the bracket containing the snap disc and magnet
under the bottom left rear corner as shown in Figure 16.1.
The blower speed control for this unit is adjusted at the factory,
and normally does not require further adjustment.
NOTE: When the speed control is turned clockwise, it will
click on to high speed. Continue to turn the speed control
clockwise to decrease the speed. At full clockwise, the
blower should blow gently, but should not stop.
1.
With the appliance plugged in, turn the speed control
knob to slow (full clockwise).
2.
With a small screwdriver, adjust the blower speed by
turning the adjustment mechanism through the hole on
the side of the speed control.
3.
Adjust the speed so the blower runs slowly, but does
not stop. Turn clockwise to slow the blower and
counterclockwise to increase the speed.
See page 31 for detailed operating instructions for the
blower and snap disc.
NOTE: The blower cord is equipped with a 3 pronged
(grounding) plug for your protection against shock hazard.
Do not remove.
3-1/8 in.
(80mm)
Secure blower
with 3 bolts
Snap Disc
Bracket
with Magnet
4-15/16 in.
(125mm)
4-13/16 in.
(122mm)
Secure wires
with wire tie
MANUAL
MANUAL: Over-rides the
Snap Disc
FAN
AUTO
LOW
HIGH
AUTO: Fan will turn ON/OFF
Automatically by the Snap Disc
13-15/16 in. (355mm)
OFF
Controls the Fan Speed
Figure 16.2 - Blower Housing
Dimensions
Figure 16.1
CAUTION
Shock Risk.
• Do NOT remove grounding prong from plug.
• Plug directly into properly grounded 3 prong receptacle.
• Route cord away from appliance.
• Do NOT route cord under or in front of appliance.
Page 16
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
5
Chimney Requirements
A. Venting Components
B. Chimney Systems
Chimney Connector:
Prefabricated Metal Chimney
• Must be minimum 6 inch (152mm) diameter (ID) high
temperature chimney listed to UL 103 HT (2100oF) or
ULC S629M.
It is also known as flue pipe or stove pipe. The chimney
connector joins the stove to the chimney. It must be a 6 inch
(152mm) minimum diameter 24 gauge mild steel black or 26
gauge blued steel, or an approved air-insulated double wall
venting pipe.
Thimble:
A manufactured or site-constructed device installed in
combustible walls through which the chimney connector
passes to the chimney. It is intended to keep the walls
from igniting. Site constructed thimbles must meet NFPA
211 Standards. Prefabricated must be suitable for use with
selected chimney and meet UL103 Type HT Standards. Follow
instructions provided by the manufacturer for manufactured
thimbles for masonry chimney and prefabricated chimneys.
•
Must use components required by the manufacturer
for installation.
•
Must maintain clearances required by the manufacturer
for installation.
•
Refer to manufacturers instructions for installation.
NOTE: In Canada when using a factory-built chimney it must
be safety listed, Type UL103 HT (2100oF) CLASS “A” or
conforming to CAN/ULC-S629M, STANDARD FOR 650oC
FACTORY-BUILT CHIMNEYS.
Chimney:
Listed Termination Cap
The chimney can be new or existing, masonry or prefabricated
and must meet the following minimum requirements specified
in Section 5B.
Storm Collar
Flashing
Listed Termination Cap
Roof Brace (if required)
Listed Chimney
Storm Collar
Flashing
Ceiling Support
Trim Collar on
Inside Wall
Chimney
Connector
Chimney
Connector
Listed Chimney
Insulated " T "
Wall Support
Thimble
Floor
Protector
Figure 17.1 Prefabricated Exterior Chimney
September 9, 2014
Floor
Protector
Figure 17.2 - Prefabricated Interior Chimney
7033-277J
Page 17
R
3100 Wood Stove Series (ACC)
Thimble
C
L
Site constructed for masonry chimney installation:
ceiling
Components
• A minimum length of 12 inches [305mm] (longer for
thicker walls) of solid insulated factory-built chimney
length constructed to UL 103 Type HT 6 inch (152mm)
inside diameter. Chimney needs to extend a minimum
of 2 inches (51mm) from the interior wall and a minimum of 1 inch (25mm) from the exterior wall.
Wall
Minimum18.0”
NFPA 211
1.5 2x2 framing stud
2.0 min air clearance
1.0 min air clearance
4.5
1.5”
2.0”
1.0”
• Wall spacer, trim collar and wall band to fit solid pack
chimney selected.
17.0” OD 14.0” ID 8.0”
1.0”
• Minimum 8 inch (203mm) diameter clay liner section (if
not already present in chimney) and refractory mortar.
C
L
2.0”
1.5”
Center of Hole
Thimble
Air Clearances
• Masonry chimney clearance must meet NFPA 211 minimum requirement of 2 inches (51mm) to sheet metal
supports and combustibles.
Include depth
of hearth pad
• Minimum of 1 inch (25mm) clearance around the chimney connector.
• Top of wall opening is a minimum of 13-1/2 inches
(343mm) from ceiling or 4-1/2 inches (114mm) below
minimum clearance specified by chimney connector
manufacturer. NFPA 211 minimum vertical clearance of
18 inches (457mm) from chimney connector and ceiling or minimum recommended by chimney connector
manufacturer. Figure 18.1.
13.5” below ceiling to top
of opening
or top of opening is a min.of
4.5” below min.clearance
specified by connector mfg.
Figure 18.1
Solid Pack Chimney with Metal Supports as a Thimble
Instructions:
1. Open inside wall at proper height for the chimney connector to entry the masonry chimney. Figure 18.1
2. Entry hole to masonry chimney must be lined with an 8
inch (203mm) minimum diameter clay liner, or equivalent, secured with refractory mortar.
3. Construct a 17 inch x 17 inch (432mm x 432mm) outside dimension frame from 2 x 2 framing lumber to
fit into wall opening. Inside opening of frame should
be no less than 14 inch x 14 inch (356mm x 356mm).
Figure 18.1.
Fire Clay Flue
Liner
with Airspace
8. Insert a section of chimney connector into the chimney.
Make sure it does not protrude past the edge of the
clay chimney liner inside the chimney.
9. Seal the end of the chimney connector to the clay liner
with refractory mortar.
10. Install trim collar around the sold pack chimney section.
Page 18
7033-277J
Wall Band to
Secure Chimney
Section
Chimney
Connector
5. Nail the frame into the wall opening. The spacer should
be on the chimney side.
7. Tightly secure the length of the solid insulated chimney
with the wall band to the masonry chimney.
Wall Spacer
Chimney Section
with 2 inch
(51mm)
Clearance to
Combustibles
4. Attach the wall spacer to the chimney side of the
frame.
6. Insert the section of the solid insulated chimney into
the outer wall of the masonry chimney.
Masonry
Chimney
Trim Collar
Wood Studs Used
for Framing - Spaced
2 inch (51mm)
clearance from
Masonry Chimney
Figure 18.2
WARNING
Fire Risk.
Do NOT pack insulation or other combustibles between
spacers.
• ALWAYS maintain specified clearances around venting and spacers.
• Install spacers as specified.
Failure to keep insulation or other material away from
vent pipe may cause fire.
September 9, 2014
R
3100 Wood Stove Series (ACC)
Solid Pack Chimney with Metal Supports as a
Thimble (Cont’d)
C. Installing Chimney Components
Chimney Connector
Single wall connector or stove pipe.
Min. Chimney Clearance to
Wall Spacer and
Combustibles - 2 inch (51mm)
This must be at least 24 gauge mild steel or 26 gauge blue
steel. The sections must be attached to the appliance and to
each other with the crimped (male) end pointing toward the
stove. All joints, including the connection at the flue collar,
should be secured with 3 sheet metal screws. Make sure
to follow the minimum clearances to combustibles. Where
passage through the wall, or partition of combustible construction is desired in Canada, the installation shall conform
to CAN/CSA-B365.
Min. Clearance
2 inch (51mm)
1 inch (25mm) Air
Space to Chimney
Section
Chimney Flue
Liner
Fireclay
Liner or
Equivalent
Chimney
Connector
Chimney Section
Factory-built listed chimney connector (vented).
Trim Collar
A listed connector (vented) must be used when installing this
unit in a mobile home. The listed connectors must conform
to each other to ensure a proper fit and seal.
Wall Band
Wall Spacer
Masonry Chimney
Constructed to NFPA 211
Figure 19.1
Chimney Height / Rise and Run
Crimped
End
Toward
Stove
This product was designed for and tested on a 6 inch (152mm)
chimney, 14 to 16 feet (420-480cm) high, (includes stove
height) measured from the base of the appliance. The further
your stack height or diameter varies from this configuration,
the possibility of performance problems exists.
Chimney height may need to be increased by 2 - 3% per
each 1000 feet above sea level. It is not recommended to
use offsets or elbows at altitudes above 4000 feet above sea
level or when there are other factors that affect flue draft.
Flue Gas
Direction
Secure pipe sections with a
minimum of 3 screws
Figure 19.2 Chimney Connector (Stove Pipe)
WARNING
WARNING
Fire Risk.
Follow Chimney Connector Manufacturer’s
Instructions for Proper Installation.
Fire Risk.
Inspection of Chimney:
• Chimney must be in good condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be 6 inch
(152mm) UL103 HT.
ONLY use connector:
• Within the room, between appliance and ceiling or wall.
Connector shall NOT pass through:
• Attic or roof space
• Closet or similar concealed space
• Floor or ceiling
Maintain minimum clearances to combustibles
WARNING
Asphyxiation Risk.
• DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVICING ANOTHER APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.
May allow flue gases to enter the house.
September 9, 2014
WARNING
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to the owner’s information manual provided with this appliance. For assistance or additional information consult a
qualified installer, service agency or your dealer.
7033-277J
Page 19
R
3100 Wood Stove Series (ACC)
D. Chimney Termination Requirements
Follow manufacturers instructions for clearance, securing,
flashing and terminating the chimney.
• Must have an approved and listed cap
• Must not be located where it will become plugged by
snow or other material
•
Must terminate at least 3 feet (91cm) above the roof
and at least 2 feet (61cm) above any portion of the
roof within 10 feet (305cm).
•
Must be located away from trees or other structures
NOTE:
• Chimney performance may vary.
• Trees, buildings, roof lines and wind conditions affect
performance.
• Chimney height may need adjustment if smoking or
overdraft occurs.
E. 2-10-3 Rule
These are safety requirements and are not meant to assure proper flue draft.
Less than 10 ft. (305cm)
2 ft. (61cm)
2 ft. (61cm)
3 ft. (91cm)
Minimum
10 ft. (305cm) To Nearest Roofline
3 ft. (91cm)
Minimum
Pitched Roof
Figure 20.1
10 ft. (305cm) or more
Less than 10 ft. (305cm)
Wall or Parapet
2 ft. (61cm) Minimum
3 ft. (91cm) Minimum
3 ft. (91cm) Minimum
Flat Roof
Figure 20.2
Page 20
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
6
Mobile Home Installation
You must use a Quadra-Fire Outside Air Kit Part
OAK-ACC and (depending on floor installation), Part
SRV7033-041 for installation in a mobile home.
SparkArestor Cap
1. An outside air inlet must be provided for combustion See
page 14 & 15 for installation information.
Storm Collar
Roof Flashing
2. Appliance must be secured to the mobile home structure
by bolting the pedestal through hearth pad and into
floor.
3. Appliance must be grounded with #8 solid copper
grounding wire or equivalent and terminated at each end
with N.E.C. approved grounding device.
Joist Shield/Firestop
Double wall
connector pipe
4. Appliance must be installed with an approved UL103 HT
ventilated chimney connector, UL103 HT chimney, and
terminal cap with spark arrestor. Never use a single wall
connector (stove pipe) in a mobile home installation. Use
only double-wall connector pipe, Dura-Vent DVL, Selkirk
metalbestos DS or Security DL double-wall connector or
any listed double-wall connector pipe.
5. In Canada, this appliance must be connected to a 6 inch
(152mm) factory-built chimney conforming to CAN/ULC629M, STANDARD FOR FACTORY BUILT CHIMNEYS.
6. Follow the chimney and chimney connector manufacturer’s
instructions when installing the flue system for use in a
mobile home.
OutsideAir
Rear Vent
Floor Protector
7. Maintain clearance to combustibles.
8. Floor protection requirements must be followed
precisely.
9. Use silicone to create an effective vapor barrier at the
location where the chimney or other component penetrates
to the exterior of the structure.
NOTE: Offsets from the vertical, not exceeding 45°, are
allowed per Section 905(a) of the Uniform Mechanical Code
(UMC). Offsets greater than 45° are considered horizontal
and are also allowed, providing the horizontal run does not
exceed 75% of the vertical height of the vent. Construction,
clearance and termination must be in compliance with the
UMC Table 9C. This installation must also comply with NFPA
211.
NOTE: Top sections of chimney must be removable to allow
maximum clearance of 13.5 feet (411cm) from ground level
for transportation purposes.
Outside Air Floor Vent
Figure 21.1
CAUTION
THE STRUCTURAL INTEGRITY OF THE MOBILE HOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED
Do NOT cut through:
• Floor joist, wall, studs or ceiling trusses.
• Any supporting material that would affect the structural
integrity.
10. Burn wood only. Other types of fuels may generate
poisonous gases (e.g., carbon monoxide).
11. If unit burns poorly while an exhaust blower is on in
home, (i.e., range hood), increase combustion air.
WARNING
Asphyxiation Risk.
NEVER INSTALL IN A SLEEPING ROOM.
Consumes oxygen in the room.
12. Installation shall be in accordance with the Manufacturers
Home & Safety Standard (HUD) CFR 3280, Part 24.
September 9, 2014
7033-277J
Page 21
R
3100 Wood Stove Series (ACC)
7
Appliance Set Up
A. Pedestal Assembly and Ash Removal
System (ARS) Installation for Step Top
Uni-body
NOTE: The Ash Removal System, must be
installed first before installing the pedestal.
ARS Cover
Included in Kit: Door assembly, door handle & magnet,
ash drawer, fastener package. A cover plate that is required
for a floor outside air installation on a pedestal model is also
included, If not needed, discard.
Tools Required: Phillips head screwdriver, 7/16 socket
wrench, 3/32 and 5/36 Allen wrench.
2
2
Remove 2 bricks for
installation and then re-install
Figure 22.1
Begin installing the ARS System.
1. Remove 2 front bricks as shown in Figure 22.1.
2. Lay body of stove on its back on a protective pad or pallet.
3. Remove the 2 nuts and 2 bolts holding the channel in
place and set the channel aside. Discard the 2 nuts.
Install the gasket over the 8 protruding screws.
Door Handle
Glossy side of
Gasket
against firebox
bottom
The glossy side of the gasket needs to go against the firebox
bottom.
It is important the gasket is not put on upside
down as it could compromise its sealing capabilities. Figure 22.2.
4. Install ash door assembly by sliding the rod at an angle
into the slot on the left side. As the rod starts passing
through the slot, slide the handle over the rod and then
finish pushing the rod through the slot.
Slide the ash door over the 8 screws protruding from the
bottom of the stove. Secure with nuts and washers provided. Figure 22.2.
Lay stove flat on
protective padding or
pallet
Magnet
Start sliding rod at
an angle into slot,
slide handle over rod
and then finish
pushing through slot.
Ash Door
Assembly
Figure 22.2
Set Screw
(align with flat
side of rod)
5. Re-install handle using a 3/32 Allen wrench to tighten the
set screw in the door handle. The set screw needs to be
snug. Figure 22.3.
6. Install magnet using a Phillips head screw driver. This
magnet will hold the door handle in an open position
which in turn holds the ash door open so ashes can be
brushed into the ash drawer. Figure 22.2.
WARNING
Ash Door Rod shown
in installed position
Do NOT operate before fully assembling components.
Burning your stove without a pedestal or leg kit
attached:
•
•
Page 22
Will void your warranty.
May result in property damage or personal injury.
7033-277J
Door handle must be
in open position to
tighten set screw
Figure 22.3
September 9, 2014
R
3100 Wood Stove Series (ACC)
Pedestal and Ash Removal System (Cont.)
Installing Pedestal Assembly
1. Remove screws on adapter and slide pedestal over adapter
on bottom of stove. Figure 23.1.
2. Line up holes in sides of pedestal with holes in adapter.
3. Securely tighten pedestal into place.
4. Carefully stand stove up and place in desired location.
Cover
5. Slip wooden decorative strips onto pedestal edges.
ARS
Channel
Finishing the ARS Installation
1. Re-install the ARS channel that was removed in Step 3 on
page one and secure with 2 bolts previously removed.
Set the cover into the ARS channel Replace the 2
front cut bricks. Figure 23.3.
2. Install the ash drawer.
Replace both bricks
back into firebox
3. Check to make sure baffle boards and ceramic blanket are
in their proper locations. (see page 29).
NOTE: If installing a floor installation of an outside air kit on a
Step Top model with a pedestal assembly you must attach
the enclosed cover plate to the back of the stove. Other wise
you may discard this piece. Figure 23.2.
Figure 23.3
B. Leg Kit and Ash Removal Installation
(ARS) for Step Top Uni-Body
Adapters
Ash Removel
Drawer
NOTE: The Ash Removal System, must be
installed first before installing the legs.
Begin installing the ARS System.
Oak
Pedestal
Trim
1. Follow steps 1 through 6 on page 22. See also Figures
22.2 and 22.3.
Installing Leg Kit
1. Remove leg mounting brackets packaged inside firebox.
2. Attach the 2 bottom screws of the mounting brackets to
the bottom of the stove with 1/4”-20 Phillips head screws.
These screws are located in the component pack .
Leave the bottom 2 screws loose so you can slide the ash
pan assembly bottom slots over the screw heads. This allows
the weight of the ash pan to rest on the screws while you are
attaching the top 2 screws. Once the ash pan is attached,
tighten all screws. Figure 24.2. (page 24)
Figure 23.1
3. Loosely assemble bolts into the corner of the mounting
brackets for leg attachment. Figure 24.1. (page 24)
Rope to Seal
Pedestal
Cover
Plate
4. Slide legs onto mounting brackets making sure the legs
are up against the bracket and secure with bolts supplied.
There are leveling bolts in 2 legs. These leveling legs
should be in opposite corners. Figure 24.1. (page 24)
5. Carefully stand stove up and place in desired location. Do
NOT tilt up on the cast iron legs, it could damage the legs.
6. Use leveling bolts on legs to stabilize and level stove.
Figure 23.2
September 9, 2014
7033-277J
Page 23
R
3100 Wood Stove Series (ACC)
Finishing the ARS Installation
1. Follow steps 1 through 3 on page 22. See also Figure
22.2.
C. Door Handle Assembly
1. Install washer on door handle shaft.
2. Slide door handle through door.
3. Install second washer(s) as shown.
4. Install key in groove.
Leg Mounting Brackets are
packaged inside firebox.
5. Align groove in latch cam with key; slide latch cam over
shaft
6. Install locknut but do not overtighten as the door
handle needs to move smoothly.
7. Install spring handle turning in a counter-clockwise
motion to desired location on door handle rod.
CAUTION
Leveling Legs at
opposite corners
• Do NOT overtighten lock nut.
• Door handle needs to move smoothly.
Figure 24.1
Latch Cam
Door Cross Section
Locknut
Spring Handle
Door Handle
Spacing Washers
Square Key
Figure 24.3
Lay stove flat on its
back on protective
padding or pallet
Ash Drawer
D. Decorative Tile Installation (31M-ACC-LE)
1. Remove tile frame from side by lifting up and pulling away
from stove. Figure 25.1
Insert 2 bottom
screws loosely
2. Stack tiles in tile frame as shown in Figure 25.2.
Leg Brackets
3. Reattach tile frame.
Figure 24.2
Tile Dimensional Requirements:
CAUTION
Max Thickness: 5/16”
Do NOT tilt the unit on the cast iron legs.
Max Length/Width: 11-7/8” square
•
Tilting could lead to property damage.
•
Lift the unit upright and place it into position on the floor
protector.
Page 24
Min Length/Width: 11-11/16” square
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
Figure 25.1
Figure 25.2
September 9, 2014
7033-277J
Page 25
R
3100 Wood Stove Series (ACC)
8
Operating Instructions
B. Wood Selection & Storage (Cont.)
A. Over-Firing Your Appliance
to keep the chimney hot for as long as it takes to dry the
wood out - about one hour. It is a waste of energy to burn
unseasoned wood of any kind.
WARNING
Fire Risk
Do not over-fire.
Over-firing may ignite creosote or will damage
the stove and chimney.
To prevent over-firing your stove, DO NOT:
• Use flammable liquids
• Overload with wood
• Burn trash or large amounts of scrap lumber
• Permit too much air to the fire
1. Symptoms of Over-Firing
Symptoms of over-firing may include one or more of the
following:
• Chimney connector or appliance glowing
Dead wood lying on the forest floor should be considered
wet, and requires full seasoning time. Standing dead wood
can be considered to be about 2/3 seasoned. To tell if wood
is dry enough to burn, check the ends of the logs. If there
are cracks radiating in all directions from the center, it is dry.
If your wood sizzles in the fire, even though the surface is
dry, it may not be fully cured.
Splitting wood before it is stored reduces drying time. Wood
should be stacked so that both ends of each piece are
exposed to air, since more drying occurs through the cut
ends than the sides. This is true even with wood that has
been split. Store wood under cover, such as in a shed, or
covered with a tarp, plastic, tar paper, sheets of scrap plywood, etc., as uncovered wood can absorb water from rain
or snow, delaying the seasoning process.
• Roaring, rumbling noises
• Loud cracking or banging sounds
C. Burning Process
• Metal warping
In recent years there has been an increasing concern about
air quality. Much of the blame for poor air quality has been
placed on the burning of wood for home heating. In order to
2. What To Do if Your Stove is Over-Firing
improve the situation, we at Quadra-Fire have developed
• Immediately close the door and air controls to reduce cleaner-burning wood stoves that surpass the requirements
for emissions established by our governing agencies. These
air supply to the fire.
wood stoves, like any other appliances, must be properly
• If you suspect a chimney fire, call the fire department
operated in order to insure that they perform the way they are
and evacuate your house.
designed to perform. Improper operation can turn most any
• Contact your local chimney professional and have your wood stove into a smoldering environmental hazard.
stove and stove pipe inspected for any damage.
1. Kindling or First Stage
• Do not use your stove until the chimney professional
It helps to know a little about the actual process of burning in
informs you it is safe to do so.
order to understand what goes on inside a stove. The first
Hearth & Home Technologies WILL NOT warranty stoves
stage of burning is called the kindling stage. In this stage, the
that exhibit evidence of over-firing. Evidence of over-firing
wood is heated to a temperature high enough to evaporate the
includes, but is not limited to:
moisture which is present in all wood. The wood will reach
the boiling point of water (212°F) and will not get any hotter
• Warped air tube
until the water is evaporated. This process takes heat from
• Deteriorated refractory brick retainers
the coals and tends to cool the appliance.
• Deteriorated baffle and other interior components
Fire requires three things to burn - fuel, air and heat. So, if
• Chimney fire
B. Wood Selection & Storage
Burn only dry seasoned wood. Store wood under cover, out
of the rain and snow. Dry and well-seasoned wood will not
only minimize the chance of creosote formation, but will give
you the most efficient fire. Even dry wood contains at least
15% moisture by weight, and should be burned hot enough
Page 26
heat is robbed from the appliance during the drying stage,
the new load of wood has reduced the chances for a good
clean burn. For this reason, it is always best to burn dry,
seasoned firewood. When the wood isn’t dry, you must
open the air controls and burn at a high burn setting for a
longer time to start it burning. The heat generated from the
fire should be warming your home and establishing the flue
draft, not evaporating the moisture out of wet, unseasoned
wood, resulting in wasted heat.
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
2. Second Stage
The next stage of burning, the secondary stage, is the period
when the wood gives off flammable gases which burn above
the fuel with bright flames. During this stage of burning it is
very important that the flames be maintained and not allowed
to go out. This will ensure the cleanest possible fire. If the
flames tend to go out, it is set too low for your burning conditions. The air control located at the upper right hand corner
is used to adjust for burn rates. This is called the Burn Rate
Air Control. Figure 26.1.
3. Final Stage
The final stage of burning is the charcoal stage. This occurs
when the flammable gases have been mostly burned and only
charcoal remains. This is a naturally clean portion of the burn.
The coals burn with hot blue flames.
The second function of the Start-Up Air Control is operation
of the rear air system. The rear air is used primarily during
a High Burn Rate. However, in some instances rear air is
desired during normal operation to help with combustion of
fuel towards the back of the firebox particularly when burning
hardwoods. The rear air is controlled independently from the
ACC system. Slide the Start-Up Air Control between the first
and third marker as indicated on the label to allow rear air to
enter the firebox. Figure 27.1.
2. Manual Timer Over-Ride
If you need to shut the ACC system off before it shuts itself
off after 25 minutes (i.e. overfire situation), reach down to
the bottom right rear corner and pull the lever toward you.
Figure 27.2.
It is very important to reload your appliance while enough
lively hot coals remain in order to provide the amount of heat
needed to dry and rekindle the next load of wood. It is best
to open the Burn Rate Air and Start-Up Air Controls before
reloading. This livens up the coal bed and reduces excessive
emissions (opacity/smoke). Open door slowly so that ash or
smoke does not exit appliance through opening. You should
also break up any large chunks and distribute the coals so
that the new wood is laid on hot coals.
HIGH
Burn Rate
Air Control
MED
LOW
Air quality is important to all of us, and if we choose to use
wood to heat our homes we should do so responsibly. To do
this we need to learn to burn our stoves in the cleanest way
possible. Doing this will allow us to continue using our wood
stoves for many years to come.
D. Automatic Combustion Control (ACC)
Typically, when you build a fire, you open the air controls fully
and monitor the fire to prevent it from going into an overfire
situation and/or burning your wood up too quickly before you
shut down the air controls to the desired burn rate. With the
Automatic Combustion Control (ACC) system, you do not
have to continually monitor the fire. Once you set the ACC
system it will control the fire for you. Follow the instructions
below to learn how to operate your stove with ease.
Start-Up
Air Control
Figure 27.1
E. Air Controls
1. Start-Up Air Control
The Start-Up Air Control has two primary functions. The
first function is to activate the Automatic Combustion Control
system (ACC). This function is performed by sliding the control all the way back until it stops at the “HI” indicator on the
label and then pulling forward to the front of the stove until
it stops. This activates the ACC system and opens the front
air channel and allows air to enter the front of the stove for
approximately 25 minutes. The front air channel gradually
shuts down until it is completely closed at the end of the 25
minutes. The fire is now controlled by the air supplied by the
Burn Rate Air Control. This function should be performed
each time you reload the stove. Figure 27.1.
September 9, 2014
7033-277J
Pull Forward
to Shut Down
Manual
Timer (ACC)
Shut Down
Figure 27.2
Page 27
R
3100 Wood Stove Series (ACC)
2. Burn Rate Air Control
4. Medium-Low Burn Rate - 10,000 to 15,000 BTU/hr
This air supply enters at the upper front of the firebox, near
the top of the glass door. This preheated air supplies the
necessary fresh oxygen to mix with the unburned gases,
helping to create second, third and fourth combustions. This
air is regulated by the Burn Rate Air Control. There are four
settings High, Medium-High, Medium-Low and Low. When
the control is raised all the way up it is on the High setting and
when pushed all the down it is on the Low setting. Figure 28.1.
Raise the Burn Rate Air Control up to the bottom of
the middle marker and stop. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and
then pull forward until it stops. This activates the timer
system (ACC).
5. Low Burn Rate - Below 10,000 BTU/hr
Leave the Burn Rate Air Control at the bottom marker.
Slide the Start-Up Air Control all the way back until it
stops (HI marker) and then pull forward until it stops.
This activates the timer system (ACC).
F. Burn Rates and Operating Efficiency
For maximum operating efficiency
HIGH
1. This appliance has a timer system (ACC) that operates
the stove at its maximum efficiency removing any guess
work for the homeowner. Follow the instructions below
for each burn rate for the Start-Up Air Control and Burn
Rate Air Control. Figure 28.1.
Shown with Side
Shield Removed
LOW
2. Burn dry, well-seasoned wood.
Low (Closed)
Burn Rates
High (Open)
1. Starting a Fire and Reloading
Open both controls fully by raising the Burn Rate Air
Control all the way up until it stops and slide the Start-up
Air Control back until it stops. After loading the stove with
wood and starting the fire, set both controls to the desired
setting by following the burn rate instructions below.
Burn Rate
Air Control
Front Air Channel
Operated by Timer
NOTE: These are approximate settings, and will vary with
type of wood or chimney draft. Due to altitude and other
environmental circumstances, this operational information is
a guideline only.
Start-Up Air
Control
Timer
Rear Air Channel
Operates independently
from Timer
Timer Manual
Shut-off
2. High Burn Rate - Maximum Heat
Raise the Burn Rate Air Control all the way up until it stops
(top marker) to a fully open position. Slide the Start-Up Air
Control all the way back until it stops (HI marker) and leave
it there. This setting over-rides the timer system (ACC) so
you must monitor the fire closely while in this setting.
START-UP
REAR AIR
HI
WARNING
Risk of Fire.
When set on High Burn Rate and over-riding
the Automatic Combustion Control system an
overfire situation can occur and may result in a
chimney fire.
Overfiring will void the stove warranty.
3. Medium-High Burn Rate - 15,000 to 30,000 BTU/hr
Raise the Burn Rate Air Control all the way up until it
stops (top marker) to a fully open position. Slide the
Start-Up Air Control all the way back until it stops (HI
marker) and then pull forward until it stops. This activates
the timer system (ACC).
Closed
Wide
Open
“HI” setting
over-rides
Timer
After activating the timer (ACC), if the control is placed
within the rear air section on the label it will allow rear air
to enter the firebox. This will not interfere with the timer
gradually closing the front air channel in 25 minutes. If
control is set on “HI” it over-rides the timer (ACC).
Figure 28.1
NOTE: Operate appliance on High Burn 15 minutes a
day to help keep flue/chimney clean.
Page 28
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
G. Correct Baffle & Blanket Placement
INCORRECT POSITIONS
WARNING
Fire Risk
Firebox damage due to improper baffle placement is not covered by warranty. Operate the
wood burning appliance with the baffle in the
correct position only.
Not doing so could result in:
• Reduced efficiency
• Overheating the chimney
• Overheating the rear of the firebox
• Poor performance
Ensure correct baffle placement and replace baffle components if damaged or missing.
Ceramic Blanket and Baffle Board are NOT in contact with the back of the firebox.
Back of Firebox
Ceramic Blanket
CAUTION
The baffle boards are FRAGILE. Use extreme caution when
loading firewood to prevent:
• Cracking, breaking or damaging the baffle boards
DO NOT operate the stove without baffle boards
Baffle Board
Ceramic Blanket is NOT in contact with the back of
the firebox and NOT even with the Baffle Board in
the front.
CORRECT POSITION
Back of Firebox
Ceramic Blanket
Back of Firebox
Baffle Retainer Bracket
Ceramic Blanket
Baffle Board
Baffle Board
Ceramic Blanket and Baffle Board MUST
be in contact with the back of the firebox and even with each other in the front.
Figure 29.1
September 9, 2014
Ceramic Blanket is bunched up at the back of the
firebox and NOT even with the Baffle Board in the
front.
Figure 29.2
7033-277J
Page 29
R
3100 Wood Stove Series (ACC)
H. Building A Fire
Baffle Board even with front
tube & resting on all tubes
Before lighting your first fire in the stove:
1. Confirm the baffle is correctly positioned. It should be
even with the front tube and resting on all tubes. Figure
30.1.
2. Follow instructions on page 34 for cleaning plated surfaces, if applicable.
3.
Burn Rate
Air Control
Remove all labels from glass.
There are many ways to build a fire. The basic principle
is to light easily-ignitable tinder or paper, which ignites the
fast burning kindling, which in turn ignites the slow-burning
firewood. Here is one method that works well:
Start-Up
Air
Control
1. Open the Burn Rate Air and Start-Up Air Controls fully.
2. Place several wads of crushed paper on the firebox floor.
Heating the flue with slightly crumpled newspaper before
adding kindling keeps smoke to a minimum.
Ceramic Blanket on Top
3. Lay small dry sticks of kindling on top of the paper.
4. Make sure that no matches or other combustibles are in
the immediate area of the appliance. Be sure the room
is adequately ventilated and the flue unobstructed.
5. Light the paper in the appliance. NEVER light or rekindle
fire with kerosene, gasoline, or charcoal lighter fluid; the
results can be fatal.
6. Once the kindling is burning quickly, add several fulllength logs 3 inches (76mm) or 4 inches (102mm) in
diameter. Be careful not to smother the fire. Stack the
pieces of wood carefully; near enough to keep each
other hot, but far enough away from each other to allow
adequate air flow between them.
Tube Channels
Figure 30.1
7. Set the Burn Rate Air Control and activate the timer
system (ACC).
8. When ready to reload, It is best to fully open both the
Burn Rate Air and Start-up Air Controls before reloading. This livens up the coal bed and reduces excessive
emissions (opacity/smoke). Open door slowly so that
ash or smoke does not exit appliance through opening.
Large logs burn slowly, holding a fire longer. Small logs
burn fast and hot, giving quick heat.
9. As long as there are hot coals, repeating steps 6 through
8 will maintain a continuous fire throughout the season.
NOTE:
• Build fire on brick firebox floor.
• Do NOT use grates, andirons or other methods to support
fuel.
It will adversely affect emissions.
Page 30
2 pc Baffle Board
7033-277J
WARNING
Fire Risk
Do NOT store wood:
• Closer than required clearances to combustibles to appliance
• Within space required for loading or ash
removal.
Do NOT operate appliance:
• With appliance door open.
• With ash removal system door open.
WARNING
Fire Risk.
• Do NOT burn wet or green wood.
• Store wood in dry location.
• Stack wood so both ends are exposed to air.
Wet, unseasoned wood can cause accumulation of
creosote.
September 9, 2014
R
3100 Wood Stove Series (ACC)
I. Blower Operating Instructions
J. Opacity (Smoke)
NOTE: If your Quadra-Fire wood stove is equipped with an
optional blower, you should follow these guidelines:
This is the measure of how cleanly your appliance is burning. Opacity is measured in percent; 100% opacity is when
an object is totally obscured by the smoke column from a
chimney, and 0% opacity means that no smoke column can
be seen. As you become familiar with your appliance, you
should periodically check the opacity. This will allow you to
know how to burn as nearly smoke-free as possible (goal of
0% opacity).
1.
Initial (cold) start-up and all Burn Settings
The blower can be plugged in and turned on right away.
The blower fan is turned on and off by a snap disc.
When your stove has reached a certain temperature
the blower will turn on and when your stove has cooled
down to a certain temperature it will turn off.
NOTE: The blower can still be left on at all burn rates
even if you have deactivated the snap disc with the
manual over-ride knob. See page 16.
Fire Risk.
2.
The blower is equipped with a speed control. Adjust
the fan speed by turning the speed control clockwise
to “Low” or counterclockwise to “High”.
• DO NOT BURN GARBAGE OR FLAMMABLE
FLUIDS SUCH AS GASOLINE, NAPTHA OR
ENGINE OIL.
3.
Snap Disc Location
If you find the blower coming on and off at undesirable
temperatures, relocate the snap disc to another location
in the designated zone on the back of the appliance.
Figure 31.1 There is a manual over-ride switch to
deactivate the snap disc, if necessary. See page 31.
WARNING
• Do NOT burn treated wood or wood with salt (driftwood).
• May generate carbon monoxide if burn material other than
wood.
May result in illness or possible death.
WARNING
Fire Risk.
Keep combustible materials, gasoline
and other flammable vapors and
liquids clear of appliance.
• Do NOT store flammable materials in the appliance’s
vicinity.
• DO NOT USE GASOLINE, LANTERN FUEL,
KEROSENE, CHARCOAL LIGHTER FLUID OR
SIMILAR LIQUIDS TO START OR “FRESHEN UP” A
FIRE IN THIS HEATER.
• Keep all such liquids well away from the heater while it is
in use.
• Combustible materials may ignite.
CAUTION
When burning your first fire, you will experience smoke and
odor from the appliance resulting from the curing of paint
and burning off of any oils remaining from manufacturing.
OPEN WINDOWS DURING INITIAL BURN TO DISSIPATE
SMOKE AND ODORS!
Figure 31.1
K. Frequently Asked Questions
ISSUES
•
•
Odors may be irritating to sensitive individuals.
Smoke detectors may activate.
SOLUTIONS
Odor from appliance
When first operated, this appliance may release an odor for the first several hours. This is
caused by the curing of the paint and the burning off of any oils remaining from manufacturing.
Metallic noise
Noise is caused by metal expanding and contracting as it heats up and cools down, similar to
the sound produced by a furnace or heating duct. This noise does not affect the operation or
longevity of the appliance.
Whirring sound
If the optional blower has been installed, the blower produces a whirring sound which
increases in volume as the speed is increased.
September 9, 2014
7033-277J
Page 31
R
3100 Wood Stove Series (ACC)
9
Maintaining & Servicing Your Appliance
A. Quick Reference Maintenance Guide
BAFFLE & BLANKET PLACEMENT
INSPECT FIREBRICKS & ASH COVER
(AFTER EACH CLEANING)
Back of Firebox
Baffle Retainer Bracket
Ceramic Blanket
2
Step Top Models Only
Baffle Board
Baffle and blanket placement is critical to heat output, efficiency and overall life of the unit. Make sure
the baffle is pushed all of the way to the back of the
firebox and the blanket is laying flat.
Firebrick is designed to protect your firebox. Replace
firebricks that are crumbling, cracked or broken. If
you have an optional ash door, check to make sure
the door is closing properly.
CHIMNEY & CAP INSPECTION
DOOR & LATCH CHECK
Keeping the door and glass
gasket in good shape will
maintain good burn times on
a low burn setting.
Listed Termination Cap
Storm Collar
The chimney and chimney
cap must be inspected for
soot and creosote during
the burn season. This will
prevent pipe blockage, poor
draft, and chimney fires.
2
Flashing
Check the glass frame for
loose screws to prevent air
leakage.
Listed Chimney
Ceiling Support
Chimney
Connector
Latch Cam
Door Cross Section
Locknut
Always burn dry wood to
help prevent cap blockage
and creosote build-up.
Spring Handle
Floor
Protector
Door Handle
Spacing Washers
Square Key
Check the door latch for proper adjustment. This
is very important especially after the door rope has
formed to the stove face.
Start the first inspection of your unit after
the first 2 months of use, or if performance
changes, and adjust your schedule accordingly.
Maintenance is required for safe operation and must be performed to maintain
your warranty.
These are generic drawings and may not represent your model.
Page 32
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
B. General Maintenance
2. Ash Removal System (ARS) Operating and Cleaning
1. Creosote (Chimney) Cleaning
•
•
•
•
Frequency: Every 2 months during heating season or
as recommended by a certified chimney sweep; more
frequently if chimney exceeds or is under 14-16 ft.
(measured from bottom of appliance)
By: Certified Chimney Sweep
Remove all ash from the firebox and extinguish all hot embers
before disposal. Allow the appliance to cool completely.
Disconnect flue pipe or remove baffle and ceramic blanket
from appliance before cleaning chimney. Otherwise residue
can pile up on top of the baffle and ceramic blanket and
the appliance will not work properly. (See Baffle Removal
on page 36). Close the door tightly. The creosote or soot
should be removed with a brush specifically designed for
the type of chimney in use. Clean out fallen ashes from the
firebox.
It is also recommended that before each heating season
the entire system be professionally inspected, cleaned and
repaired if necessary.
Frequency: As necessary
By: Homeowner
CAUTION
Injury Risk.
• Gloves recommended
• May have sharp edges
a. The stove and ashes must be completely cooled down
before using the Ash Removal System. Reach down and
locate the ash removal door handle under the left side of
the stove in the center. Squeeze the handle and push all
the way back. A magnet will hold the handle in place which
in turn holds the ash door open.
b. Clean ash down through the ash removal system grate into
the drawer below. If there are large pieces in the ashes,
you can remove the grate before brushing the ash into the
drawer.
Make sure all ash is removed from the top of ARS door.
Lift up the grate and inspect the top of the door to ensure
all ash has been removed. You can rapidly move the ARS
latch handle up and down to help remove any ash from the
door. Use a small brush to clean off the top of the door if
any ash remains.
Inspection: Inspect the system at the appliance connection
and at the chimney top. Cooler surfaces tend to build creosote
deposits quicker, so it is important to check the chimney from
the top as well as from the bottom.
Formation and Need For Removal: When wood is burned
slowly, it produces tar and other organic vapors which combine
with expelled moisture to form creosote.
The creosote vapors condense in the relatively cool chimney flue
of a newly-started or a slow-burning fire. As a result, creosote
residue accumulates on the flue lining. When ignited, this
creosote creates an extremely hot fire which may damage the
chimney or even destroy the house.
Be sure to replace the grate before operating the stove.
Remember to leave 1/4 to 1/2 inch (6-13mm) of ash on
the firebox floor to act as a natural grate, allowing air to
flow freely underneath wood.
c. Close the door handle, you will hear a “click” when it closes.
The ash drawer will not pull out if the door handle is left in
the open position. Wear gloves to remove the drawer.
Dispose of the ashes following the directions on page 34.
The chimney connector and chimney should be inspected
once every 2 months during the heating season to determine
if a creosote or soot buildup has occurred. If creosote or soot
has accumulated, it should be removed to reduce the risk of a
chimney fire.
WARNING
Fire Risk
Injury Risk
WARNING
Make sure Ash Removal System door is sealed
tight against the gasket.
Fire Risk.
Prevent creosote buildup.
• Inspect chimney connector and chimney once
every two months during heating season.
Air leakage may cause:
• Over-fire condition.
• Flame and/or smoke spillage.
• Remove creosote to reduce risk of chimney fire.
• Wood to burn too fast.
• Ignited creosote is extremely HOT.
WARNING
Fire Risk.
• Do not use chimney cleaners or flame colorants in your appliance.
Will corrode pipe.
September 9, 2014
7033-277J
Page 33
R
3100 Wood Stove Series (ACC)
3. Disposal of Ashes
•
•
Frequency: When ash is within 1-3/4 in. (44mm) of
firebox lip
By: Homeowner
Ashes should be placed in a metal container with a
tight fitting lid. The closed container of ashes should
be placed on a non-combustible floor or on the ground,
well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial
in soil or otherwise locally dispersed, they should be
retained in the closed container until all cinders have
thoroughly cooled.
stain the glass and damage the finish on plated metal
surfaces.
A portion of the combustion air entering the firebox is deflected
down over the inside of the door glass. This air flow “washes”
the glass, helping to keep smoke from adhering to its surface.
When operated at a low burn rate, less air will be flowing over
the glass and the smoky, relatively cool condition of a low fire
will cause the glass to become coated.
Operating the appliance with the Burn Rate Air Control and
Start-Up Air Control all the way open for 15-20 minutes should
remove the built up coating.
CAUTION
WARNING
Handle glass assembly with care.
Fire Risk.
Disposal of Ashes
Glass
Assembly
• Ashes should be placed in metal container with tight
fitting lid.
• Do not place metal container on combustible
surface.
• Ashes should be retained in closed container until all
cinders have thoroughly cooled.
•
•
•
•
Do NOT use abrasive cleaners.
Use a hard water deposit glass cleaner on white film.
Use commercial oven cleaner on heavier deposits.
Remove all residue of oven cleaner or will permanently
stain glass on next firing.
•
Refer to maintenance instructions.
4. Cleaning Plated Surfaces
•
•
When cleaning glass:
• Avoid striking, scratching or
slamming glass.
• Do NOT clean glass when hot.
Frequency: Prior to first burn and then as desired
By: Homeowner
Clean all the fingerprints and oils from plated surfaces
BEFORE firing the appliance for the first time. If not
cleaned properly before lighting your first fire, the oils
can cause permanent markings on the plating.
C. Glass Replacement
1.
After the plating is cured, the oils will not affect the
finish and little maintenance is required. Wipe clean as
needed.
Ensure that the fire is out and the appliance is cool to the
touch.
2.
Protect a table or counter top with padding or towels.
Protect your hands and wear gloves to prevent injury.
3.
Remove the door with the broken glass by lifting the door
up and off of the hinges.
4.
Lay door face down on a table or counter making sure the
handle hangs over the edge so the door lays flat, on a soft
surface.
5.
Remove the screws from each glass retainer and remove
the glass. (If screws are difficult to remove, soak with
penetrating oil first).
6.
Center the glass with edges evenly overlapping the opening in the door, (i.e. same space top and bottom, left and
right sides).
7.
Replace the glass retainers. Be careful not to cross thread
the screws.
8.
Tighten each retainer just a few turns until each is
secured. Check again for centering of glass in door
frame. Continue to tighten each retainer alternately, a
few turns at a time, until the glass is secure. DO NOT
OVERTIGHTEN.
CAUTION
• Do not use polishes with abrasives.
It will scratch plated surfaces.
5. Glass Cleaning
• Frequency: As desired
• By: Homeowner
Clean glass with a non-abrasive glass cleaner. Abrasive
cleaners may scratch and cause glass to crack. If the
deposits on the glass are not very heavy, normal glass
cleaners work well. Heavier deposits may be removed by
using a damp cloth dipped in wood ashes or by using a
commercially available oven cleaner.
After using an oven cleaner, it is advisable to remove any
residue with a glass cleaner or soap and water. Oven
cleaner left on during the next firing can permanently
Page 34
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
9.
Replace the door on the appliance.
10.1
10.1
Quadra-Fire stoves are equipped with ceramic super heatresistant glass, which can only be broken by impact or
misuse. Do not slam stove door or impact the glass. When
closing door, make sure that logs do not protrude against the
glass. Inspect glass regularly. If you find a crack or break,
immediately put the fire out and return the door to your dealer
for replacement of glass before further use.
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10
.4
10.1
10.1
10.1
10.2 10.2 10.2
10.2
10.3
9”
8”
1-1/4”
WARNING
2”
1-1/4”
10.4
2”
5”
Handle glass with care.
3”
9”
Figure 35.1 - 3100 Millennium Brick Assembly
• Inspect the gasket to ensure it is
undamaged.
Glass
Assembly
1-1/4”
10.3
No.
• Do NOT strike, slam or scratch glass.
• Do NOT operate appliance with glass
& door assembly removed.
• Do NOT operate with glass cracked, broken or scratched.
WARNING
Brick Size
Qty
10.1
9 x 4-1/2 x 1-1/4
12
10.2
6 x 4-1/2
4
10.3
9 x 4-1/2 with angle (see drawing)
1
10.4
9 x 3 with angle (see drawing)
1
y
Fire Risk.
4.1
Injury Risk.
4.1
4.1
• Use only glass specified in manual.
4.1
No brick,
Grate Location
4.4
4.1
Glass breakage will occur.
4.1
4.1
4.1
• DO NOT REPLACE with any other material.
4.5
4.2
D. Firebrick Replacement
4.2
4.2
4.1
4.4
4.1
4.2
4.3
9”
Replace the firebrick if they become crumbly and/or if there
is a 1/4 inch (6.35mm) gap between the bricks.
8”
1-1/4”
Inspect the firebrick after each ash removal.
2”
The firebox is lined with high quality firebrick, which has
exceptional insulating properties. There is no need to use a
grate; simply build a fire on the firebox floor. Do not operate
appliance without firebrick.
1-1/4”
4.3
5”
1-1/4”
2”
4.5
3”
9”
Figure 35.2 - 3100 Step Top Brick Assembly
No.
Brick Size
Qty
4.1
9 x 4-1/2 x 1-1/4
1. After the coals have completely cooled, remove all old
brick and ash from unit and vacuum firebox.
10
4.2
6 x 4-1/2
4
4.3
9 x 4-1/2 with angle (see drawing)
1
2. Remove new brick set from box and lay out to diagram
shown.
4.4
4-1/2 x 4-1/2 x 1-1/4
2
4.5
9 x 3 with angle (see drawing)
1
3. Lay bottom bricks in unit.
4. Install rear bricks on the top of the bottom bricks. Slide
top of bricks under clip on back of firebox wall and push
bottom of brick back.
5. Install side bricks. Slide top of brick under clips on side
of firebox and push the bottom of the brick until it is flush
with the side of the appliance.
September 9, 2014
Use Part 832-0550 when ordering individual brick. Provide brick
dimension or copy this page, mark the desired brick and take it to
your authorized dealer.
NOTE: The Ash Removal System is available
for the Step Top Model only and not for the
Millennium Model.
7033-277J
Page 35
R
3100 Wood Stove Series (ACC)
E. Baffle Removal
F. Snap Disc Replacement
1. Remove all ash from the firebox, and extinguish all hot 1. Locate the snap disc bracket assembly at the bottom left
rear corner of the stove. Figure 36. 3
embers before disposal into a metal container.
2. The baffle board has 2 pieces. With the ceramic blanket 2. A magnet holds the bracket to the stove. Pull the bracket
down away from the stove to expose the snap disc.
still in place, slide one baffle piece over the top of other one
and pull out top piece through the door opening and then 3. Pull the snap disc and spade connectors up and out of
remove bottom baffle piece. Figure 36.1
bracket as shown in Figure 36.4.
3. Remove the ceramic blanket.
4. Using a Phillips head screw driver, remove the 2 screws
from the snap disc and then remove the snap disc from
4. Re-install the baffle pieces one piece at a time. Be sure
the spade connectors. Replace with new snap disc and
the baffle boards are even with the front manifold tube and
re-connect to spade connectors.
is resting on all tubes. See page 30.
5. To re-install the ceramic blanket, it is easier to fold it in 5. Push the snap disc and spade connectors back inside
bracket and re-attach the bracket to the stove.
half first. Place on top of baffle board, open up and flatten
and smooth out the blanket. Re-check the baffle board for
correct positioning. Figure 36.2.
Figure 36.1 - Baffle
Snap Disc Location
Figure 36.3
Snap Disc
Magnet
Spade
Connectors
Figure 36.2 - Ceramic Blanket
Figure 36.4
Page 36
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
G. Tube Channel Assembly Replacement
NOTE: Service Space
Removing Tube Channel Assembly
1. Remove the right side shield by removing 2 screws in the
back using a Phillips head screw driver.
2. Remove 4 screws from channel access cover and remove
cover.
In order to replace the tube channel assembly a clearance
of 19 inches (483mm) is required on the right side of stove
in order to remove the tubes with the stove in place.
If space is not available, the stove will have to be disconnected from the chimney to proceed with the tube replacement.
3. Locate 2 channel nuts inside of chamber and remove
using a 7/16 socket wrench. Slide out tube channel
assembly.
NOTE:
Soak the bolts with penetrating oil for at least 15
minutes before trying to remove them.
Replacing Tube Channel Assembly
1. Slide one gasket onto each tube.
2. Slide the tube channel assembly into side of firebox and
insert each tube into the corresponding hole in the tube
channel rack starting with the back hole first.
3. Make sure tube channel assembly is flush against the
side of the stove and secure with channel nuts.
4. Re-install channel cover and side shield.
Slide one gasket
over each tube
Tube Channel Rack
Channel
Access
Cover
Channel Cover
Screws (4)
Remove
2 Screws
Channel
Nuts (2)
Tube Channel
Assembly
Side Panel
Figure 37.1
September 9, 2014
7033-277J
Page 37
R
3100 Wood Stove Series (ACC)
10
Troubleshooting
Start Fire Problems
Can’t get fire started
Excessive smoke or spillage
Burns too slowly
Smolders, sizzles
With proper installation, operation, and maintenance your wood stove
will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualified service person in
the diagnosis of a problem and the corrective action to be taken.
Possible Cause
Solution
Not enough kindling/paper or no
kindling/paper
Use dry kindling, more paper. Arrange kindling &
wood for air movement.
Not enough air for fire to ignite
Check for restricted cap/shroud
Open outside air kit (if installed).
Check for flue blockage.
Pre-warm flue before starting fire (refer to starting
fire section).
Check for adequate vent height (refer to chimney
assembly section).
Open window below the appliance towards the
wind.
Wood condition is too wet, too
large
Use dry, seasoned wood (refer to wood fuel section).
Bed of coals not established
before adding wood
Start with paper & kindling to establish bed of
coals (refer to starting fire section).
Flue blockage such as birds’
Have chimney inspected for creosote and cleaned
nests or leaves in termination cap by a certified chimney sweep.
Down draft or negative pressure
Do not use exhaust fans during start-up (refer to
Competition with exhaust devices negative pressure section).
Open window below the appliance towards the
wind.
Fire burns too fast
Extremely dry or soft wood
Mix in hardwood.
Mix in less seasoned wood after fire is established
(refer to wood fuel section).
Overdrafting
Check for correct vent height; too much vertical
height creates overdrafting.
Check location of vent termination (refer to chimney requirements section).
Page 38
ARS door may not be closed
completely
Handle set screw rotated on ash door rod - Follow
installation instructions
Ash left on ARS door
No seal is created. Clean off top of ARS door for
complete seal.
7033-277J
September 9, 2014
11
Reference Materials
A. Exploded Drawing & Service Parts
R
31M-ACC
Service Parts
Millennium - Wood Stove
Beginning Manufacturing Date: July 2006
Advanced Combustion Control (ACC)
Ending Manufacturing Date: Active
31M-ACC-MBK (7/06 - Active),
31M-ACC-GT (7/06 - 10/06), 31M-ACC-NT (7/06 - 10/06)
1
3
4
2
5
14
6
7
13
12
8
9
10
11
Part number list on following page.
09/14
September 9, 2014
7033-277J
Page 39
R
31M-ACC
Service Parts
Beginning Manufacturing Date: July 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
1
Air Channel, Convection w/Bracket (Retain Original SN Label)
2
Air Supply Back
SRV7033-134
3
Flue Collar
SRV7000-302
4
Panel Assembly, Side, Left
7033-019
5
Rear Channel Assembly
7033-002
6
Tube Support Rack
7033-148
7
Brick Retainer
7033-149
8
Ceramic Fiber Blanket, 1/2“ Thick (19” W x 13-3/4” H)
832-3390
Y
9
Baffle Board - 9-1/2 in W x 13-3/4 in H
SRV7033-209
Y
SRV7033-144
Pkg of 2
Y
Y
# 10 Brick Set
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10
.4
10.1
10.2
10.1
10.1
10.1
10.2 10.2 10.2
10.3
9”
8”
1-1/4”
2”
10
1-1/4”
10.3
5”
1-1/4”
2”
Brick Assembly - Complete Set
10.4
9”
Pkg of 18
10.1
Brick, 9 x 4-1/2 x 1-1/4”
Qty. 12 Req.
10.2
Brick, 6 x 4-1/2 x 1-1/4”
Qty. 4 Req.
10.3
Brick, 9 x 4-1/2 x 1-1/4” w/angles, see diagram
Qty. 1 Req.
10.4
Brick, 9 x 3 x 1-1/4” w/angle, see diagram
Qty. 1 Req.
Brick, Uncut
3”
SRV7033-006
Pkg of 1
832-0550
Pkg of 6
832-3040
11
Panel Assembly, Side, Right
7033-017
12
Tube Channel Top - Tube Channel Access Cover
SRV7033-237
13
Tube, Channel Assembly
Manifold Tubes
SRV7033-023
Y
Additional service part numbers appear on following page.
Page 40
7033-277J
September 9, 2014
R
31M-ACC
Service Parts
Beginning Manufacturing Date: July 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
#14 Burn Rate Controls & Accociated Parts
14.10
14.1
14.9
14.2
14.3
14.1
14.8
14.5
14.6
Burn Rate Control Assembly
Spring Handle, 1/4”, Gold
14.2
14.4
Pre SN 0071959142
Spring Handle, 1/4”, Nickel
Spring Handle, 1/4”, Black
Post SN 0071959142
14.7
7033-033
Y
832-0630
Y
250-8340
Y
SRV7000-614
Y
14.3
Door Gasket - Front & Rear Air Timer Doors
7033-282
Y
14.4
Timer Air Control Assembly
SRV7033-052
Y
7033-024
Y
Y
Rear Air Door Assembly
14.5
Rear Air Control Arm Assembly
7033-035
14.6
Start-Up Control Knob
7000-343
14.7
Air Control Rod Guide
7033-210
14.8
Latch, Magnet
14.9
Timer Arm Assembly
7033-034
Y
14.10
Timer (Only) Replacement Assembly
SRV480-1940
Y
For Air Control
229-0631
#15 Pedestal Assembly
15.1
15.2
15.3
15.1
Pedestal Riser
7033-207
15.2
Pedestal Base
7033-163
15.3
Strip, Oak Trim
Pkg of 2
#16 Baffle Protection channel
832-0560
Front, looking into unit
Side view
Baffle
protection
Channel sits
In between
Front tube and
Fiber baffle.
16
Baffle Protection channel
Additional service part numbers appear on following page
September 9, 2014
7033-277J
Ceramic blanket
Fiber baffle
This tab sits behind the front tube.
SRV7033-298
Page 41
R
31M-ACC
Service Parts
Beginning Manufacturing Date: July 2006
Ending Manufacturing Date: Active
17.1
#17 Door Assembly
17.2
17.6
17.3
17.7
17.5
17.4
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement
parts for your appliance please provide model number and serial number. All parts listed
in this manual may be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Black
17.1
17.2
Door Assembly
No longer available
Hinge Pins, 1/2”
DR-31/43BK-FH
832-1912
DR-31/43NL-FH
Gold (Pkg of 2)
832-0250
Nickel (Qty 2 req)
430-5320
Door Handle Assembly
7000-606/2
832-0540
Cam Latch
430-1141
Key, Cam Latch
17.4
PART NUMBER
Nickel Trim
Black (Pkg of 2)
17.3
Stocked
at Depot
430-1151
Nut, Locking Door Handle
Pkg of 24
226-0100/24
Y
Screw, Flat Head Philips 8-32 X 1/2
Pkg of 10
832-0860
Y
Washer, Sae, 3/8
Pkg of 3
832-0990
Y
Gold
832-0620
Y
Nickel
250-8330
Y
Black
SRV7000-613
Y
Spring Handle, Door 1/2”
17.5
Trim, Ring, Door
17.6
Door Glass Assembly - 15-1/2 in. W x 13-3/8 in H
17.7
Glass Frame Set
No longer available
430-2682
No longer available
430-5340
7000-012
Y
4 Pieces
832-0350
Gold Trim Doors
436-5350
Nickel Trim Doors
436-5360
Gasket, Glass Tape - Field Cut to Size
5 Ft
832-0460
Y
Rope, Door, 3/4” X 84” - Field Cut to Size
7 Ft
832-1680
Y
Component Pack (Includes Spring Handles (1) 1/2” & (2) 1/4”,
(2) Hinge Pins, Quadra-Fire Logo)
Label, Burn Rate Air Control
7033-160
Label, Start-Up Air Control
7033-166
Additional service part numbers appear on following page.
Page 42
7033-277J
September 9, 2014
R
31M-ACC
Service Parts
Beginning Manufacturing Date: July 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for
your appliance please provide model number and serial number. All parts listed in this manual may
be ordered from an authorized dealer.
ITEM
DESCRIPTION
COMMENTS
Blower, Convection - Replacement Blower
Stocked
at Depot
PART NUMBER
812-4900
Hinge Pins, 1/2”, Gold
Pre SN 0071959142
Hinge Pins, 1/2”, Nickel
Hinge Pins, 1/2”, Black
Post SN 0071959142
Logo, Quadra-Fire
Spring Handle, 1/2”, Gold
Spring Handle, 1/2”, Nickel
Spring Handle, 1/2”, Black
Spring Handle, 1/4”, Black
200-3240
Post SN 0071959142
Component Pack (Includes Touch-Up Paint, Spring Handles (1)
1/2” and (2) 1/4”, Trimount Plug, Owners Manual and Warranty
Card).
7000-606/2
Nickel
Pre SN 0071959142
Spring Handle, 1/4”, Nickel
430-5320
200-3180
Post SN 0071959142
Spring Handle, 1/4”, Gold
832-0250
Gold
Pre SN 0071959142
Black & Gold Trim
Nickel Trim
Paint Touch-Up
Y
832-0620
Y
250-8330
Y
SRV7000-613
Y
832-0630
Y
250-8340
Y
SRV7000-614
Y
7033-027
7033-029
812-0910
Plug, Trimount, .250”
Pkg of 24
229-0880/24
Y
Door Handle Assembly
832-0540
Y
Upgrade, Door, Nickel
UK-DRNL
Gasket, Manifold
Pkg of 4
7038-168/4
Y
ACCESSORIES
Blower Assembly
BK-ACC
Blower Control Box w/Switch
SRV7000-194
Component Pack
7033-051
Snap Disc Bracket Assembly
SRV7033-036
Snap Disc, # 1, Convection Blower
SRV230-0470
Wire Harness, Blower
7033-262
Outside Air Kit, Floor & Rear
Y
Y
OAK-ACC
Outside Air Collar Assembly
7033-039
Outside Air Shield
33271
Y
Outside Air Cover Plate Assembly
SRV7033-041
Y
RIVNUT-REPAIR
Y
FASTENERS
Avk Rivnut Repair Kit - 1/4-20 & 3/8-16 Rivnut Tools
Bolt, Hex Head, 1/4-20 x 1
Pkg of 10
25221A/10
Y
Button Head 1/4-20 x .5
Pkg of 20
32328/20
Y
Nut, Keps Lock, 10-32
Pkg of 40
226-0050/40
Y
Nut, Keps Lock, 8-32
Pkg of 40
226-0060/40
Y
Nut, Ser Flange Small 1/4-20
Pkg of 24
226-0130/24
Y
Screw, Sheet Metal #8 x 1/2 S-Grip
Pkg of 40
12460/40
Y
Washer, 1/4 Sae
Pkg of 24
28758/24
September 9, 2014
7033-277J
Y
Page 43
B. Exploded Drawing & Service Parts
R
31ST-ACC
Service Parts
Beginning Manufacturing Date: Sept. 2006
Step Top - Wood Stove
31ST-ACC (Advanced Combustion Control) Ending Manufacturing Date: Active
1
3
2
4
14
13
12
5
10
6
9
7
11
8
Part number list on following page.
09/14
Page 44
7033-277J
September 9, 2014
R
31ST-ACC
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
1
Air Channel, Convection w/Bracket (Retain Original SN Label)
SRV7033-144
2
Air Supply Back
SRV7033-134
3
Panel Assembly, Side, Left
7033-038
#4 Brick Set Assembly
4.1
4.1
4.1
4.1
4.1
4.1
4.1
4.4
4.1
4.5
4.2
No brick,
Grate Location
4.2
4.2
4.1
4.4
4.1
4.2
4.3
9”
8”
1-1/4”
2”
4
1-1/4”
4.3
5”
Brick Assembly - Complete Set
1-1/4”
2”
3”
9”
Pkg of 18
4.1
Brick, 9 x 4-1/2 x 1-1/4”
Qty. 10 Req.
4.2
Brick, 6 x 4-1/2 x 1-1/4”
Qty. 4 Req.
4.3
Brick, 9 x 4-1/2 x 1-1/4” w/angles, see diagram
Qty. 1 Req.
4.4
Brick, 4-1/2 x 4-1/2 x 1-1/4”
Qty. 2 Req.
4.5
Brick, 9 x 3 x 1-1/4” w/angle, see diagram
Qty. 1 Req.
Brick, Uncut
4.5
SRV7033-032
Pkg of 1
832-0550
Pkg of 6
832-3040
5
Tube Support Rack
7033-148
6
Brick Retainer
7033-149
7
Ceramic Fiber Blanket, 1/2“ Thick (19” W x 13-3/4” H)
832-3390
Y
8
Baffle Board - 9-1/2 in W x 13-3/4 in H
SRV7033-209
Y
9
Rear Channel Assembly
7033-002
Y
10
Access Cover
SRV7038-196
Pkg of 2
Handle, Access Cover
SRV7038-197
11
Panel Assembly, Side, Right
7033-037
12
Tube Channel Top - Tube Channel Access Cover
SRV7033-237
13
Tube, Channel Assembly
Manifold Tubes
SRV7033-023
Y
Additional service part numbers appear on following page.
September 9, 2014
7033-277J
Page 45
R
31ST-ACC
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
#14 Burn Rate Control Assembly
#15 Leg Assembly
14.10
14.1
#16 Pedestal Assembly
15.1
16.1
16.3
14.9
14.2
15.3
14.3
14.4
14.8
14.5
16.2
15.2
14.7
14.6
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
14.1
DESCRIPTION
COMMENTS
Burn Rate Control Assembly
PART NUMBER
7033-033
Y
Black ( Qty 1)
SRV7000-614
Y
Gold (Pkg of 2)
832-0630
Y
14.2
Spring Handle, Air Control 1/4”
250-8340
Y
14.3
Door Gasket - Front & Rear Air Timer Doors
7033-282
Y
14.4
Timer Air Control Assembly
SRV7033-052
Y
7033-024
Y
Y
Nickel (Qty 2 req)
Rear Air Door Assembly
14.5
Rear Air Control Arm Assembly
7033-035
14.6
Start-Up Control Knob
7000-343
14.7
Air Control Rod Guide
7033-210
14.8
Latch, Magnet
For Air Control
229-0631
14.9
Timer Arm Assembly
7033-034
Y
14.10
Timer (Only) Replacement Assembly
SRV480-1940
Y
15.1
Ash Pan Assembly
7033-008
Ash Pan Leg - ARS
15.2
15.3
7033-050
Black
831-1240
Gold
831-1250
Nickel
LEGS-QANL
Leg Mount Brackets
Pkg of 2
SRV7033-183
Pedestal
For Air Control
PED-3143
Legs, Queen Anne
16.1
Pedestal Assembly
7033-013
16.2
Strip, Oak Trim
832-0560
Door Assembly - ARS
SRV7033-015
Ash Pan Door Handle - ARS
7033-274
16.3
Ashpan Assembly
Y
7033-010
Component Pack (Includes Gasket for Ash Removal,
Magnet and Fasteners)
Leg
7033-048
Pedestal
7033-045
Gasket - ARS
SRV7033-296
Y
Latch, Handle Assembly - ARS
SRV7033-047
Y
Magnet Round
SRV7000-140
Y
Additional service part numbers appear on following page.
Page 46
7033-277J
September 9, 2014
R
31ST-ACC
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
Fiber Handle Assembly
#17 Door Assembly
Spring Handle Assembly
17.1
17.4
17.3
17.5
17.2
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
17
17.1
DESCRIPTION
COMMENTS
Door Assembly
Hinge Pins, 1/2”
17.2
Rope, Door, 3/4” X 84” - Field Cut to Size
17.3
Door Glass Assembly - 15-1/2 in. W x 13-3/8 in H
Gasket, Glass Tape - Field Cut to Size
17.4
Glass Frame Set
17.5
Door Handle Assembly
Spring Handle, Door 1/2”
Stocked
at Depot
PART NUMBER
Black
DR-31/43BK-FH
Nickel
DR-31/43NL-FH
Black (Pkg of 2)
7000-606/2
Gold (Pkg of 2)
832-0250
Nickel (Qty 2 req)
430-5320
7 Ft
832-1680
Y
7000-012
Y
5 Ft
832-0460
Y
4 Pieces
832-0350
Spring
832-0540
Fiber
SRV7033-071
Y
Gold
832-0620
Y
Nickel
250-8330
Y
Cam Latch
430-1141
Key, Cam Latch
430-1151
Nut, Locking Door Handle
Pkg of 24
226-0100/24
Y
Screw, Flat Head Philips 8-32 X 1/2
Pkg of 10
832-0860
Y
Washer, Sae, 3/8
Pkg of 3
832-0990
Y
Trim, Ring, Door
No longer available
430-2682
No longer available
430-5340
Upgrade, Door, Nickel
UK-DRNL
Front, looking into unit
Side view
Ceramic blanket
Fiber baffle
Baffle
protection
Channel sits
In between
Front tube and
Fiber baffle.
18
This tab sits behind the front tube.
Baffle Protection Channel
SRV7033-298
Additional service part numbers appear on following page.
September 9, 2014
7033-277J
Page 47
R
31ST-ACC
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers.
Stocked
at Depot
Provide model number and serial number when requesting service parts from your dealer or
distributor.
ITEM
DESCRIPTION
COMMENTS
Blower, Convection - Replacement Blower
PART NUMBER
812-4900
Channel, Ash Removal
Step-Top
7033-172
Component Pack (Includes Spring Handles (1) 1/2” & (2) 1/4”,
(2) Hinge Pins, Quadra-Fire Logo)
Gold Trim Doors
436-5350
Nickel Trim Doors
436-5360
Hinge Pins, 1/2” (Qty 2)
Logo, Quadra-Fire, Black
Spring Handle, 1/4”
Gold
832-0250
Nickel
430-5320
Pkg of 10
7000-694/10
Gold (Pkg of 2)
832-0630
Y
Nickel (Qty 2 req)
250-8340
Y
Component Pack, Step Top, (Touch-Up Paint, Owners Manual &
Warranty Card). Spring Handles in Door Assembly.
Component Pack (Includes Touch-Up Paint, Spring Handles (1)
1/2” and (2) 1/4”, Trimount Plug, Owners Manual and Warranty
Card).
Y
7033-043
Black & Gold Trim
7033-027
Nickel Trim
7033-029
Paint Touch-Up
812-0910
Plug, Trimount, .250”
Gasket, Manifold
Pkg of 24
229-0880/24
Y
Pkg of 4
7038-168/4
Y
Label, Burn Rate Air Control
7033-160
Label, Start-Up Air Control
7033-166
ACCESSORIES
Blower Assembly
BK-ACC
Blower Control Box w/Switch
SRV7000-194
Component Pack
7033-051
Snap Disc Bracket Assembly
SRV7033-036
Snap Disc, # 1, Convection Blower
SRV230-0470
Wire Harness, Blower
7033-262
Black
Leg Kit & Ash Removal System (ARS)
No longer available
Nickel
Outside Air Kit, Floor & Rear
Y
Y
LEG-3143-BK
LEG-3143-GD
LEG-3143-NL
OAK-ACC
Outside Air Collar Assembly
7033-039
Outside Air Shield
33271
Y
Outside Air Cover Plate Assembly
SRV7033-041
Y
FASTENERS
Page 48
Bolt, Hex Head, 1/4-20 x 1
Pkg of 10
25221A/10
Y
Button Head 1/4-20 x .5
Pkg of 20
32328/20
Y
Nut, Keps Lock, 10-32
Pkg of 40
226-0050/40
Y
Nut, Keps Lock, 8-32
Pkg of 40
226-0060/40
Y
Nut, Ser Flange Small 1/4-20
Pkg of 24
226-0130/24
Y
Screw, Sheet Metal #8 x 1/2 S-Grip
Pkg of 40
12460/40
Y
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
C. Exploded Drawing & Service Parts
R
31M-ACC-LE
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
4
1
3
2
5
6
7
8
9
11
10
12
13
14
16
17
15
18
Part number list on following page.
09/14
September 9, 2014
7033-277J
Page 49
R
3100 Wood Stove Series (ACC)
R
31M-ACC-LE
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
1
Air Channel, Convection w/Bracket (Retain Original SN Label)
SRV7033-144
2
Air Supply Back
SRV7033-134
3
Flue Collar
SRV7000-302
4
Panel Assembly, Side, Left
SRV7033-082
5
Ceramic Fiber Blanket, 1/2” Thick
832-3390
6
Baffle Protection Channel
SRV7033-298
7
Tube Support Rack
7033-148
8
Brick Retainer
7033-149
9
Baffle Board
Pkg of 2
Y
SRV7033-209
#10 Brick Set Assembly
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.1
10.2
10.4
10.1
10.1
10.1
10.2
10.2
10.1
10.2
10.3
9”
8”
1-1/4”
1-1/4”
10.3
2”
1-1/4”
2”
5”
10.4
3”
9”
10
Firebrick Set, Complete Set
SRV7033-006
10.1
Brick, 9 x 4-1/2 x 1-1/4”
Qty. 12 Req.
10.2
Brick, 6 x 4-1/2 x 1-1/4”
Qty. 4 Req.
10.3
Brick, 9 x 4-1/2 x 1-1/4” w/angles, see diagram
Qty. 1 Req.
10.4
Brick, 9 x 3 x 1-1/4” w/angle, see diagram
Qty. 1 Req.
Brick, Uncut
Pkg of 1
832-0550
Pkg of 6
832-3040
11
Tube, Channel Assembly
SRV7033-023
12
Tube Channel Top
SRV7033-237
Y
13
Rear Channel Assembly
7033-002
Y
Burn Rate Control Assembly
7033-033
Y
14.1
Additi
l
Page 50
i
t
b
f ll
i
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
R
31M-ACC-LE
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
#14 Burn Rate Control Assembly
14.1
14.10
14.2
14.9
14.3
14.4
14.8
14.5
14.6
14.7
14.2
Spring Handle,1/4”
250-8340
Y
14.3
Door Gasket
7033-282
Y
14.4
Timer Air Control Assembly
SRV7033-052
Y
14.5
Control Arm Assembly, Rear Air
SRV7033-079
14.6
Knob
7000-343
14.7
Air Control Rod Guide
7033-210
14.8
Latch, Magnet
229-0631
14.9
Timer Arm Assembly
7033-034
Y
14.10
Timer (Only) Replacement Assembly
SRV480-1940
Y
15
Pedestal Assembly
SRV7033-072
16
Panel Assembly, Side Right
SRV7033-080
17
Tile Frame
SRV7033-324
Logo, Quadra-Fire
September 9, 2014
Pkg of 10
7033-277J
7000-649/10
Page 51
R
3100 Wood Stove Series (ACC)
R
31M-ACC-LE
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or distributor. Hearth and
Home Technologies does not sell directly to consumers. Provide model number and serial number when
requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
Stocked
at Depot
PART NUMBER
#18 Door Assembly
18.1
18.4
18.3
18.5
18.2
18
Door Assembly
DR-31/43BK-FH
18.1
Hinge Pin, 1/2”
430-5320
18.2
Rope, Door, 3/4” x 84”
18.3
Door Glass Assembly
7 Ft.
Gasket, Glass Tape, 3/4” x 1/8”
18.4
Glass Frame Set
18.5
Door Handle Assembly
832-1680
Y
7000-012
Y
5 Ft.
832-0460
Y
4 pcs.
832-0350
SRV7033-071
Door Handle
SRV7044-188
Fiber Handle
SRV7060-212
Washer, Sae, 3/8 (3 Ea)
Pkg of 3
Y
832-0990
Cam Latch
430-1141
Key, Cam Latch
430-1151
Nut, 2-Wy Side-Lock Jam 3
Pkg of 24
226-0100/24
Y
Screw Flat Head Philips 8-32 x 1/2
Pkg of 10
220-0490/12
Y
Component Pack Assembly
(Includes Touch-Up Paint, Handles, Owners Manual
and Warrany Card)
812-0910
Paint, Touch-Up
Additi 52 l
Page
i
t
SRV7033-083
b
f ll
i
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
R
31M-ACC-LE
Service Parts
Beginning Manufacturing Date: Sept. 2006
Ending Manufacturing Date: Active
IMPORTANT: THIS IS DATED INFORMATION. Parts must be ordered from a dealer or
distributor. Hearth and Home Technologies does not sell directly to consumers. Provide
Stocked
at Depot
model number and serial number when requesting service parts from your dealer or distributor.
ITEM
DESCRIPTION
COMMENTS
PART NUMBER
ACCESSORIES
Blower Assembly
BK-ACC
Blower Control Box w/Switch
SRV7000-194
Component Pack
7033-051
Snap Disc Bracket Assembly
SRV7033-036
Snap Disc, # 1, Convection Blower
SRV230-0470
Wire Harness, Blower
7033-262
Outside Air Kit, Floor & Rear
Y
Y
OAK-ACC
Outside Air Collar Assembly
7033-039
Outside Air Shield
33271
Y
Outside Air Cover Plate Assembly
SRV7033-041
Y
September 9, 2014
7033-277J
Page 53
R
3100 Wood Stove Series (ACC)
D. Warranty Policy
Hearth & Home Technologies Inc.
LIMITED LIFETIME WARRANTY
Hearth & Home Technologies Inc., on behalf of its hearth brands (”HHT”), extends the following warranty for
HHT gas, wood, pellet, coal and electric hearth appliances that are purchased from an HHT authorized dealer.
WARRANTY COVERAGE:
HHT warrants to the original owner of the HHT appliance at the site of installation, and to any transferee taking ownership
of the appliance at the site of installation within two years following the date of original purchase, that the HHT appliance
will be free from defects in materials and workmanship at the time of manufacture. After installation, if covered components manufactured by HHT are found to be defective in materials or workmanship during the applicable warranty period,
HHT will, at its option, repair or replace the covered components. HHT, at its own discretion, may fully discharge all of its
obligations under such warranties by replacing the product itself or refunding the verified purchase price of the product
itself. The maximum amount recoverable under this warranty is limited to the purchase price of the product. This warranty
is subject to conditions, exclusions and limitations as described below.
WARRANTY PERIOD:
Warranty coverage begins on the date of original purchase. In the case of new home construction, warranty coverage
begins on the date of first occupancy of the dwelling or six months after the sale of the product by an independent,
authorized HHT dealer/ distributor, whichever occurs earlier. The warranty shall commence no later than 24 months
following the date of product shipment from HHT, regardless of the installation or occupancy date. The warranty period for
parts and labor for covered components is produced in the following table.
The term “Limited Lifetime” in the table below is defined as: 20 years from the beginning date of warranty coverage for
gas appliances, and 10 years from the beginning date of warranty coverage for wood, pellet, and coal appliances. These
time periods reflect the minimum expected useful lives of the designated components under normal operating conditions.
Warranty Period
Parts
Labor
1 Year
2 years
HHT Manufactured Appliances and Venting
Gas
X
X
Wood
X
X
X
3 years
Pellet
EPA
Wood
Coal
X
X
X
X
X
X
X
X
X
Components Covered
Electric Venting
X
X
All parts and material except as
covered by Conditions,
Exclusions, and Limitations
listed
Igniters, electronic components,
and glass
Factory-installed blowers
Molded refractory panels
X
Firepots and burnpots
5 years
1 year
7 years
3 years
10
years
1 year
X
Limited
3 years
Lifetime
X
X
X
X
X
90 Days
X
X
X
X
X
X
X
X
Castings and baffles
X
X
Manifold tubes,
HHT chimney and termination
Burners, logs and refractory
Firebox and heat exchanger
X
X
All replacement parts
beyond warranty period
See conditions, exclusions, and limitations on next page.
4021-645C 12-29-10
Page 54
Page 1 of 2
7033-277J
September 9, 2014
R
3100 Wood Stove Series (ACC)
WARRANTY CONDITIONS:
!
"
"
WARRANTY EXCLUSIONS:
_
!
*
N
!!
!!!
!!
*
@
%
_!!"!
"!
!!!
[
*!
!
N
_`q{
!
!
!
!
;`|{
;`}{
;`~{
!!!
!
!!

;`€{
!+!
!
!"#
!
*
;`{
;`‚{
*
;`ƒ{*
;

`„{
?#!
%
#*
'
*'
!
!
This warranty is void if:
#
!
!
$
#
!!
!
!!
"
%
!
!
LIMITATIONS OF LIABILITY:
'*
'
!
!*
!
!
!
!
!
!
+8
*
+!
;
!
<=<>$
<<=<?>@$KN<NOQUZ![\<8?$<=>@<88Z@@?<8$<@?<Z@@?Q
8><]<N<@<?<N^@$?$]?Q[>U<NZ@@?Q8U[<N$N^@$?$]<
<=>@<88<NZ@@?Q8><]<NO$K<
September 9, 2014
7033-277J
Page 55
CONTACT INFORMATION:
Hearth & Home Technologies
1445 North Highway
Colville, WA 99114
Division of HNI INDUSTRIES
Please contact your Quadra-Fire dealer with any questions or concerns.
For the number of your nearest Quadra-Fire dealer,
log onto www.quadrafire.com
CAUTION
$
$) /.
3# /
!2 4
$
DO NOT DISCARD THIS MANUAL
• Important operating
and maintenance
instructions included.
• Read, understand and
follow these instructions
for safe installation and
operation.
• Leave this manual with
party responsible for
use and operation.
We recommend that you record the following pertinent
information for your 3100 WOOD STOVE (ACC)
Date purchased/installed:
Serial Number:
Location on appliance:
Dealership purchased from:
Dealer phone:
Notes:
This product may be covered by one or more of the following patents: (United States) 5341794, 5263471, 6688302, 7216645,
7047962 or other U.S. and foreign patents pending.
Page 56
7033-277J
September 9, 2014