A740G M2L+/A780LB Setup Manual
FCC Information and Copyright
This equipment has been tested and found to comply with the limits of a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. There is no guarantee
that interference will not occur in a particular installation.
The vendor makes no representations or warranties with respect to the
contents here and specially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make changes to the contents here without obligation to
notify any party beforehand.
Duplication of this publication, in part or in whole, is not allowed without first
obtaining the vendor’s approval in writing.
The content of this user’s manual is subject to be changed without notice and
we will not be responsible for any mistakes found in this user’s manual. All the
brand and product names are trademarks of their respective companies.
Table of Contents
Chapter 1: Introduction .......................................................... 1
1.1
Before You Start ................................................................................1
1.2
Package Checklist.............................................................................1
1.3
Motherboard Features......................................................................2
1.4
Rear Panel Connectors .....................................................................3
1.5
Motherboard Layout ........................................................................4
Chapter 2: Hardware Installation ........................................... 5
2.1
Installing Central Processing Unit (CPU).......................................5
2.2
FAN Headers......................................................................................7
2.3
Installing System Memory ................................................................8
2.4
Connectors and Slots .......................................................................10
Chapter 3: Headers & Jumpers Setup................................. 13
3.1
How to Setup Jumpers ....................................................................13
3.2
Detail Settings..................................................................................13
Chapter 4: RAID Functions ................................................... 18
4.1
Operating System............................................................................18
4.2
Raid Arrays ......................................................................................18
4.3
How RAID Works.............................................................................18
Chapter 5: Useful Help .......................................................... 21
5.1
Driver Installation Note .................................................................21
5.2
Software............................................................................................22
5.3
Extra Information ...........................................................................26
5.4
Troubleshooting...............................................................................28
Appendix: SPEC In Other Languages .................................... 29
German .................................................................................................................30
French....................................................................................................................32
Italian ....................................................................................................................34
Spanish ..................................................................................................................36
Portuguese............................................................................................................38
Polish .....................................................................................................................40
Russian ..................................................................................................................42
Arabic ....................................................................................................................44
Japanese................................................................................................................46
A740G M2L+/A780LB
CHAPTER 1: INTRODUCTION
1.1
BEFORE YOU START
Thank you for choosing our product. Before you start installing the
motherboard, please make sure you follow the instructions below:
1.2
„
Prepare a dry and stable working environment with
sufficient lighting.
„
Always disconnect the computer from power outlet
before operation.
„
Before you take the motherboard out from anti-static
bag, ground yourself properly by touching any safely
grounded appliance, or use grounded wrist strap to
remove the static charge.
„
Avoid touching the components on motherboard or the
rear side of the board unless necessary. Hold the board
on the edge, do not try to bend or flex the board.
„
Do not leave any unfastened small parts inside the
case after installation. Loose parts will cause short
circuits which may damage the equipment.
„
Keep the computer from dangerous area, such as heat
source, humid air and water.
PACKAGE CHECKLIST
HDD Cable X 1 (optional)
Serial ATA Cable X 2
Rear I/O Panel for ATX Case X 1
Installation Guide X 1
Fully Setup Driver DVD X 1 (full version manual files inside)
FDD Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
S/PDIF out Cable X 1 (optional)
Serial ATA Power Cable X 1 (optional)
Note: The package contents may be different due to area or your motherboard version.
1
Motherboard Manual
1.3
MOTHERBOARD FEATURES
SPEC
Socket AM2+
CPU
AMD Sempron / Athlon / Athlon II / Phenom
/ Phenom II processors
computing
Supports Hyper Transport 2.0
(Maximum Watt: 95W)
FSB
AMD 64 Architecture enables 32 and 64 bit
Support HyperTransport 2.0
Supports up to 2 GT/s Bandwidth
AMD 740G (A740G M2L+)
Chipset
AMD 780L (A780LB)
AMD SB710
Low Pin Count Interface
ITE 8718F
Super I/O
Provides the most commonly used legacy
Super I/O functionality
H/W Monitor
ITE's "Smart Guardian" function
DDR2 DIMM Slots x 2
Dual Channel Mode DDR2 memory module
Main
Max Memory Capacity 8GB
Supports DDR2 533 / 667 / 800
Memory
Each DIMM supports 256MB/512MB/
Supports DDR2 1066 (by AM2+/AM3 CPU)
1GB/2GB/4GB DDR2
Registered DIMM and ECC DIMM is not supported
Graphics
Integrated in AMD 740G Chipset
IDE
Integrated IDE Controller
SATA II
Integrated Serial ATA Controller
LAN
Realtek RTL 8102EL/8103EL/8106E
Sound
ALC662
Slots
On Board
Max Shared Video Memory is 512MB
Avivo support
Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode
supports PIO Mode 0~4,
Data transfer rates up to 3 Gb/s
SATA Version 2.0 specification compliant
10 / 100 Mb/s auto negotiation
5.1 channels audio out
High Definition Audio
PCI Express X16 slot
x1
Supports PCI-E X16 expansion cards
PCI slot
x2
Supports PCI expansion cards
Floppy Connector
x1
Each connector supports 2 Floppy drives
Connectors IDE Connector
2
Environment Control initiatives
x1
Each connector supports 2 IDE device
SATA Connector
x4
Each connector supports 1 SATA devices
Front Panel Connector
x1
Supports front panel facilities
Front Audio Connector
x1
Supports front panel audio function
A740G M2L+/A780LB
SPEC
S/PDIF out Connector
x1
Supports digital audio out function
CPU Fan Header
x1
CPU Fan power supply (with Smart Fan function)
System Fan Header
x1
System Fan Power supply
CMOS clear Header
x1
Restore CMOS data to factory default
USB Connector
x2
Each connector supports 2 front panel USB ports
Power Connector (24pin)
x1
Connects to Power supply
Power Connector (4pin)
x1
Connects to Power supply
Printer Port Connector
x1
Each connector supports 1 Printer port
PS/2 Keyboard
x1
Connects to PS/2 Keyboard
PS/2 Mouse
x1
Connects to PS/2 Mouse
Back Panel VGA port
x1
Connect to D-SUB monitor
I/O
LAN port
x1
Connect to RJ-45 Ethernet cable
USB Port
x4
Connect to USB devices
Audio Jack
x3
Provide Audio-In/Out and microphone connection
Board Size
Special
Features
182 mm(W) x 235 mm(L)
RAID 0 / 1 / 1+0 support
OS Support Windows XP / Vista 32 / Vista 64 / 7
1.4
Biostar reserves the right to add or remove support
for any OS With or without notice.
REAR PANEL CONNECTORS
PS/2
Mouse
LAN
Line In/
Surround
Line Out
Mic In 1/
Bass/ Center
PS/2
Keyboard
VGA
USBX2
USBX2
3
Motherboard Manual
1.5
MOTHERBOARD LAYOUT
CPU_FAN1
KBMS1
ATXPWR2
DIMM A1
A M 2+
VGA1
DIMM B1
Socket
ATXPWR1
USB1
B ATTE RY
RJ45USB1
IDE1
JUSBV1
AMD
740G/
A780L
AUDIO1
PEX16_1
BIOS
LAN
PCI1
Super
I/O
JSPDIFOUT1
JCMOS1
PCI2
SATA4
SATA3
F_USB1
FDD1
F_USB2
JUSBV2
Codec
F_AUDIO1
J_PRINT1
Note: ■ represents the 1st pin.
4
AMD
SB710
PANEL1
SATA1
SATA2
SYS_FAN1
A740G M2L+/A780LB
CHAPTER 2: HARDWARE INSTALLATION
2.1
INSTALLING CENTRAL PROCESSING UNIT (CPU)
Step 1: Pull the lever toward direction A from the socket and then raise the
lever up to a 90-degree angle.
Step 2: Look for the white triangle on socket, and the gold triangle on
CPU should point towards this white triangle. The CPU will fit only
in the correct orientation.
5
Motherboard Manual
Step 3: Hold the CPU down firmly, and then close the lever toward direct
B to complete the installation.
Step 4: Put the CPU Fan on the CPU and buckle it. Connect the CPU
FAN power cable to the CPU_FAN1. This completes the
installation.
Note: Please update the BIOS to the latest version while using AM2+/AM3 CPUs. Due to the latest
CPU transition, you may encounter the situation that the new system failed to boot while
using new AM2+/AM3 CPUs. In this case, please install one standard AM2 CPU to boot your
system, and update the latest BIOS from our website for AM2+/AM3 CPUs support.
6
A740G M2L+/A780LB
2.2
FAN HEADERS
These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different due to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.
CPU_FAN1: CPU Fan Header
4
1
Pin
1
2
3
4
Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control (By Fan)
SYS_FAN1: System Fan Header
Pin
1
2
3
Assignment
Ground
+12V
FAN RPM rate
sense
3
1
Note:
The CPU_FAN1 supports 4-pin head connector. The SYS_FAN1 supports 3-pin head
connector. When connecting with wires onto connectors, please note that the red wire is
the positive and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.
7
Motherboard Manual
2.3
INSTALLING SYSTEM MEMORY
DI M M A1
DI M M B1
A. Memory Modules
8
1.
Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2.
Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
A740G M2L+/A780LB
B. Memory Capacity
DIMM Socket
Location
DDR2 Module
DIMMA1
256MB/512MB/1GB/2GB/4GB
DIMMB1
256MB/512MB/1GB/2GB/4GB
Total Memory
Size
Max is 8GB.
C. Dual Channel Memory installation
Please refer to the following requirements to activate Dual Channel function:
Install memory module of the same density in pairs, shown in the table.
DIMMA1 DIMMB1
Dual Channel Status
Disabled
O
X
Disabled
X
O
Enabled
O
O
(O means memory installed, X means memory not installed.)
The DRAM bus width of the memory module must be the same (x8 or
x16)
9
Motherboard Manual
2.4
CONNECTORS AND SLOTS
FDD1: Floppy Disk Connector
The motherboard provides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk types.
2
34
1
33
IDE1: Hard Disk Connector
The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality.
40
39
2
1
SATA1~SATA4: Serial ATA Connectors
The motherboard has a PCI to SATA Controller with 4channels SATA interface, it
satisfies the SATA 2.0 spec and with transfer rate of 3Gb/s.
SATA4
SATA3
SATA1 SATA2
7
10
4
1
Pin
1
2
3
4
5
6
7
Assignment
Ground
TX+
TXGround
RXRX+
Ground
A740G M2L+/A780LB
ATXPWR1: ATX Power Source Connector
This connector allows user to connect 24-pin power connector on the ATX
power supply.
Pin
13
14
15
16
17
18
19
20
21
22
23
24
Assignment
+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground
12
24
1
13
Pin
1
2
3
4
5
6
7
8
9
10
11
12
Assignment
+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V
ATXPWR2: ATX Power Source Connector
Connecting this connector provides +12V to CPU power circuit.
2
1
3
4
Pin
1
2
3
4
Assignment
+12V
+12V
Ground
Ground
Note:
Before power on the system, please make sure that both ATXPWR1 and ATXPWR2
connectors have been plugged-in.
11
Motherboard Manual
PEX16_1: PCI-Express X16 Slot
-
PCI-Express 2.0 compliant.
Maximum theoretical realized bandwidth of 4GB/s simultaneously per
direction, for an aggregate of 16GB/s totally.
PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
PEX16_1
PCI1~PCI2: Peripheral Component Interconnect Slots
This motherboard is equipped with 2 standard PCI slots. PCI stands for
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
12
A740G M2L+/A780LB
CHAPTER 3: HEADERS & JUMPERS SETUP
3.1
HOW TO SETUP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is “close”, if not, that means the jumper is
“open”.
Pin opened
3.2
Pin closed
Pin1-2 closed
DETAIL SETTINGS
PANEL1: Front Panel Header
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC case’s front panel switch
functions.
PWR_LED
On/Off
+ + -
9
1
+ SPK
Pin
1
2
3
4
5
6
7
8
Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control
Function
Speaker
Connector
Hard drive
LED
Reset button
Pin
9
10
11
12
13
14
15
16
16
8
RST
HLED
Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground
Function
N/A
N/A
Power LED
Power-on button
13
Motherboard Manual
F_USB1/F_USB2: Headers for USB 2.0 Ports at Front Panel
These headers allow user to connect additional USB cable on the PC front panel,
and also can be connected with internal USB devices, like USB card reader.
Pin
1
2
3
4
5
6
7
8
9
10
F_ USB1
F_ USB2
2
10
1
9
Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
NC
Key
JCMOS1: Clear CMOS Header
Placing the jumper on pin2-3 allows user to restore the BIOS safe setting and
the CMOS data. Pease carefully follow the procedures to avoid damaging the
motherboard.
1
3
Pin 1-2 Close:
Normal Operation (default).
1
1
3
3
Pin 2-3 Close:
Clear CMOS data.
※ Clear CMOS Procedures:
1.
2.
3.
4.
5.
6.
14
Remove AC power line.
Set the jumper to “Pin 2-3 close”.
Wait for five seconds.
Set the jumper to “Pin 1-2 close”.
Power on the AC.
Reset your desired password or clear the CMOS data.
A740G M2L+/A780LB
F_AUDIO1: Front Panel Audio Header
This header allows user to connect the front audio output cable with the PC front
panel. This header allows only HD audio front panel connector; AC’97 connector
is not acceptable.
2
10
1
9
Pin
1
2
3
4
5
6
7
8
9
10
Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense
JSPDIFOUT1: Digital Audio-out Connector
This connector allows user to connect the PCI bracket SPDIF output header.
Pin
1
2
3
1
Assignment
+5V
SPDIF_OUT
Ground
3
15
Motherboard Manual
J_PRINT1: Printer Port Connector
This header allows you to connector printer on the PC.
2
1
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
16
Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5
25
Pin
14
15
16
17
18
19
20
21
22
23
24
25
26
Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key
A740G M2L+/A780LB
JUSBV1/JUSBV2: Power Source Headers for USB Ports
Pin 1-2 Close:
JUSBV1: +5V for USB ports at USB1/RJ45USB1.
JUSBV2: +5V for USB ports at front panel (F_USB1/F_USB2).
Pin 2-3 Close:
JUSBV1: +5V STB for USB ports at USB1/RJ45USB1.
JUSBV2: +5V STB for USB ports at front panel (F_USB1/F_USB2).
1
JUSBV1
3
3
3
1
Pin 1-2 close
1
1
1
3
3
3
1
Pin 2-3 close
JUSBV2
17
Motherboard Manual
CHAPTER 4: RAID FUNCTIONS
4.1
OPERATING SYSTEM
Supports Windows XP Home/Professional Edition, and Windows Vista.
4.2
RAID ARRAYS
RAID supports the following types of RAID arrays:
RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.
RAID 1+0: RAID 1+0 combines the techniques used in RAID 0 and RAID 1.
4.3
HOW RAID WORKS
RAID 0:
The controller “stripes” data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment.
This technique reduces overall disk access time and offers high bandwidth.
Features and Benefits
-
Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the
platform.
Uses: Intended for non-critical data requiring high data throughput, or any
environment that does not require fault tolerance.
Benefits: provides increased data throughput, especially for large files.
No capacity loss penalty for parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
fails, all data is lost.
Fault Tolerance: No.
Block 1
Block 3
Block 5
18
Block 2
Block 4
Block 6
A740G M2L+/A780LB
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.
Features and Benefits
-
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires fault tolerance and minimal capacity.
Benefits: Provides 100% data redundancy. Should one drive fail, the
controller switches to the other drive.
Drawbacks: Requires 2 drives for the storage space of one drive.
Performance is impaired during drive rebuilds.
Fault Tolerance: Yes.
Block 1
Block 2
Block 3
Block 1
Block 2
Block 3
19
Motherboard Manual
RAID 1+0:
RAID 1 drives can be stripped using RAID 0 techniques. Resulting in a RAID 1+0
solution for improved resiliency, performance and rebuild performance.
Features and Benefits
-
-
Drives: Minimum 4, and maximum is 6 or 8, depending on the platform.
Benefits: Optimizes for both fault tolerance and performance, allowing for
automatic redundancy. May be simultaneously used with other RAID
levels in an array, and allows for spare disks.
Drawbacks: Requires twice the available disk space for data redundancy,
the same as RAID level 1.
Fault Tolerance: Yes.
Block 1
Block 3
Block 5
20
Block 1
Block 3
Block 5
Block 2
Block 4
Block 6
Block 2
Block 4
Block 6
A740G M2L+/A780LB
CHAPTER 5: USEFUL HELP
5.1
DRIVER INSTALLATION NOTE
After you installed your operating system, please insert the Fully Setup
Driver DVD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the DVD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you insert the Driver DVD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
DVD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep2.html
21
Motherboard Manual
5.2
SOFTWARE
Installing Software
1. Insert the Setup DVD to the optical drive. The drivers installation program
would appear if the Autorun function has been enabled.
2. Select Software Installation, and then click on the respective software
title.
3. Follow the on-screen instructions to complete the installation.
Launching Software
After the installation process, you will see the software icon “eHOT Line” /
“BIOS Update” appears on the desktop. Double-click the icon to launch the
utility.
eHot-Line (Optional)
eHot-Line is a convenient utility that helps you to contact with our
Tech-Support system. This utility will collect the system information which is
useful for analyzing the problem you may have encountered, and then send
these information to our tech-support department to help you fix the problem.
Before you use this utility, please set Outlook Express as your default e-mail client application program.
represents important
information that you
must provide. Without
this information, you may
not be able to send out
the mail.
*
This block will show
the information which
would be collected in
the mail.
condition
* Describe
of your system.
your area or
*Select
the area close to you.
Provide the e-mail
address that you would
like to send the copy to.
the name of
*Provide
the memory module
manufacturer.
Provide the name of
the power supply
manufacturer and the
model no.
Send the mail out.
Exit this dialog.
Save these information to a .txt file
22
A740G M2L+/A780LB
After filling up this information, click “Send”
to send the mail out. A warning dialog would
appear asking for your confirmation; click
“Send” to confirm or “Do Not Send” to cancel.
If you want to save this information to a .txt file, click “Save As…” and then you
will see a saving dialog appears asking you to enter file name.
Enter the file name and then click
“Save”. Your system information
will be saved to a .txt file.
Open the saved .txt file, you will see
your system information including
motherboard/BIOS/CPU/video/
device/OS information. This
information is also concluded in the
sent mail.
We will not share customer’s data with any other third parties,
so please feel free to provide your system information while using
eHot-Line service.
If you are not using Outlook Express as your default e-mail client
application, you may need to save the system information to a .txt file
and send the file to our tech support with other e-mail application. Go
to the following web
http://www.biostar.com.tw/app/en-us/about/contact.php for getting
our contact information.
23
Motherboard Manual
BIOS Update
BIOS Update is a convenient utility which allows you to update your
motherboard BIOS under Windows system.
AWARD BIOS
Show current BIOS information
Clear CMOS function
(Only for AWARD BIOS)
Save current BIOS
to a .bin file
Update BIOS
with a BIOS file
<Backup BIOS>
Once click on this button, the saving
dialog will show. Choose the
position to save file and enter file
name. (We recommend that the file
name should be English/number
and no longer than 7 characters.)
Then click Save.
24
AMI BIOS
A740G M2L+/A780LB
<Update BIOS>
Before doing this, please download the proper BIOS file from the website.
For AWARD BIOS, update BIOS procedure
should be run with Clear CMOS function, so
please check on Clear CMOS first.
Then click Update BIOS button, a
dialog will show for asking you backup
current BIOS. Click Yes for BIOS
backup and refer to the Backup BIOS
procedure; or click No to skip this
procedure.
After the BIOS Backup procedure, the
open dialog will show for requesting the
BIOS file which is going to be updated.
Please choose the proper BIOS file for
updating, then click on Open.
The utility will update BIOS with the
proper BIOS file, and this process may
take minutes. Please do not open any
other applications during this process.
After the BIOS Update process, click on
OK to restart the system.
While the system boots up and the full screen logo shows, press
key to enter BIOS setup.
<Delete>
In the BIOS setup, use the Load Optimized Defaults function and then Save and
Exit Setup to exit BIOS setup. BIOS Update is completed.
All the information and content above about the software are subject to be changed
without notice. For better performance, the software is being continuously updated.
The information and pictures described above are for your reference only. The actual
information and settings on board may be slightly different from this manual.
25
Motherboard Manual
5.3
EXTRA INFORMATION
CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
26
A740G M2L+/A780LB
BIO-Flasher
BIO-Flasher is a BIOS flashing utility providing you an easy and simple way to
update your BIOS via USB pen drive or floppy disk.
The BIO-Flasher is built in the BIOS chip. To enter the utility, press <F12>
during the Power-On Self Tests (POST) procedure while booting up.
Updating BIOS with BIO-Flasher
1. Go to the website to download the latest BIOS file for the motherboard.
2. Then, save the BIOS file into a USB pen drive or a floppy disk.
3. Insert the USB pen drive or the floppy disk that contains the BIOS file to the
USB port or the floppy disk drive.
4. Power on or reset the computer and then
press <F12> during the POST process.
A select dialog as the picture on the right
appears.
Select the device contains the BIOS file and
press <Enter> to enter the utility.
5. The utility will show the BIOS
files and their respective
information. Select the proper
BIOS file and press <Enter>
then <Y> to perform the BIOS
update process.
6. After the update process, the utility will ask you to reboot the system. Press
<Y> to proceed. BIOS update completes.
z
z
This utility only allows storage device with FAT32/16 format and single
partition.
Shutting down or resetting the system while updating the BIOS will lead to
system boot failure.
27
Motherboard Manual
5.4
TROUBLESHOOTING
Probable
1.
2.
Solution
There is no power in the system. 1.
Power LED does not shine; the
fan of the power supply does not 2.
work
3.
Indicator light on keyboard does
not shine.
Make sure power cable is
securely plugged in.
Replace cable.
Contact technical support.
System is inoperative. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard drives are running.
module snaps into place.
System does not boot from a hard disk 1.
drive, but can be booted from optical
drive.
2.
System only boots from an optical
drive. Hard disks can be read,
applications can be used, but system
fails to boot from a hard disk.
1.
Screen message shows “Invalid
Configuration” or “CMOS Failure.”
Review system’s equipment. Make sure
correct information is in setup.
2.
System cannot boot after user installs a 1.
second hard drive.
2.
28
Check cable running from disk to
disk controller board. Make sure
both ends are securely plugged
in; check the drive type in the
standard CMOS setup.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
Back up data and applications
files.
Reformat the hard drive.
Re-install applications and data
using backup disks.
Set master/slave jumpers
correctly.
Run SETUP program and select
correct drive types. Call the drive
manufacturers for compatibility
with other drives.
A740G M2L+/A780LB
This page intentionally left blank.
29
Motherboard Manual
APPENDIX: SPEC IN OTHER LANGUAGES
GERMAN
Spezifikationen
Sockel AM2+
CPU
AMD Sempron / Athlon / Athlon II / Phenom /
Phenom II Prozessoren
64-Bit-Datenverarbeitung
Unterstützt Hyper Transport 2.0
(Maximales Watt: 95W)
FSB
Die AMD 64-Architektur unterstützt eine 32-Bit- und
Unterstützt HyperTransport 2.0 mit einer
Bandbreite von bis zu 2 GT/s
AMD 740G (A740G M2L+)
Chipsatz
AMD 780L (A780LB)
AMD SB710
Low Pin Count-Schnittstelle
ITE8718F
Super E/A
Bietet die häufig verwendeten alten Super
E/A-Funktionen.
Dual-Kanal DDR2 Speichermodul
Unterstützt DDR2 533 / 667 / 800
Arbeitsspeich Max. 8GB Arbeitsspeicher
Jeder DIMM unterstützt 256MB/512MB/
1GB/2GB/4GB DDR2.
Grafik
Integrierter AMD 740G-Chipsatz
IDE
Integrierter IDE-Controller
SATA
Integrierter Serial ATA-Controller
LAN
Realtek RTL 8102EL/8103EL/8106E
Unterstützt Avivo
Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus
Unterstützt PIO-Modus 0~4,
Datentransferrate bis zu 3 Gb/s
Konform mit der SATA-Spezifikation Version 2.0.
10 / 100 Mb/s Auto-Negotiation
5.1-Kanal-Audioausgabe
Unterstützt High-Definition Audio
tützung
PCI-Steckplatz
Onboard-Ans Diskettenlaufwerkanschluss
IDE-Anschluss
30
registrierte DIMMs. ECC DIMMs werden nicht
Max. 512MB gemeinsam benutzter Videospeicher
Audio-Unters ALC662
PCI Express X16 Steckplatz
Unterstützt DDR2 1066 (by AM2+/AM3 CPU)
unterstützt.
HD
Steckplätze
Hardware-Überwachung
"Smart Guardian"-Funktion von ITE
DDR2 DIMM-Steckplätze x 2
er
Umgebungskontrolle,
x1
x2
x1
Jeder Anschluss unterstützt 2 Diskettenlaufwerke
x1
Jeder Anschluss unterstützt 2 IDE-Laufwerke
A740G M2L+/A780LB
Spezifikationen
chluss
SATA-Anschluss
x4
Jeder Anschluss unterstützt 1 SATA-Laufwerk
Fronttafelanschluss
x1
Unterstützt die Fronttafelfunktionen
Front-Audioanschluss
x1
Unterstützt die Fronttafel-Audioanschlussfunktion
S/PDIF Ausgangsanschluss
x1
Unterstützt die digitale Audioausgabefunktion
CPU-Lüfter-Sockel
x1
System-Lüfter-Sockel
x1
"CMOS löschen"-Sockel
x1
USB-Anschluss
x2
Stromanschluss (24-polig)
x1
Stromanschluss (4-polig)
x1
Druckeranschluss Anschluss
x1
PS/2-Tastatur
x1
PS/2-Maus
x1
Rückseiten-E VGA-Anschluss
x1
LAN-Anschluss
x1
USB-Anschluss
x4
Audioanschluss
x3
/A
Platinengröß
e
Sonderfunkti
onen
OS-Unterstü
tzung
CPU-Lüfterstromversorgungsanschluss (mit Smart
Fan-Funktion)
System-Lüfter-Stromversorgungsanschluss
Jeder Anschluss unterstützt 2
Fronttafel-USB-Anschlüsse
Jeder Anschluss unterstützt 1 Druckeranschluss
182 mm (B) X 235 mm (L)
Unterstützt RAID 0 / 1 / 1+0
Biostar behält sich das Recht vor, ohne Ankündigung
Windows XP / Vista 32 / Vista 64 / 7
die Unterstützung für ein Betriebssystem
hinzuzufügen oder zu entfernen.
31
Motherboard Manual
FRENCH
SPEC
Sockel AM2+
UC
Processeurs AMD Sempron / Athlon / Athlon II / L'architecture AMD 64 permet le calcul 32 et 64 bits
Phenom / Phenom II
Prend en charge Hyper Transport 2.0
(Watt maximum : 95W)
Bus frontal
Prend en charge Hyper Transport 2.0
jusqu'à une bande passante de 2 GT/s
AMD 740G (A740G M2L+)
Chipset
AMD 780L (A780LB)
AMD SB710
Interface à faible compte de broches
ITE 8718F
Super E/S
Fournit la fonctionnalité de Super E/S
patrimoniales la plus utilisée.
Module de mémoire DDR2 à mode à double voie
Mémoire
Capacité mémoire maximale de 8 Go
principale
Chaque DIMM prend en charge des DDR2
de 256Mo/512Mo/1Go/2Go/4Go
LAN
Realtek RTL 8102EL/8103EL/8106E
Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133
Prend en charge le mode PIO 0~4,
Taux de transfert jusqu'à 3 Go/s.
Conforme à la spécification SATA Version 2.0
10 / 100 Mb/s négociation automatique
Sortie audio à 5.1 voies
ALC662
Prise en charge de l'audio haute définition
audio HD
Fentes
Connecteur
embarqué
32
Les DIMM à registres et DIMM avec code correcteurs
Prise en charge Avivo
Prise en
charge
Prend en charge la DDR2 1066 (by AM2+/AM3 CPU)
Mémoire vidéo partagée maximale de 512 Mo
Contrôleur IDE intégré
Contrôleur Serial ATA intégré
Prend en charge la DDR2 533 / 667 / 800
d'erreurs ne sont pas prises en charge
Graphiques Integré dans la chipset AMD 740G
SATA
Moniteur de matériel
Fonction "Gardien intelligent" de l'ITE
Fentes DDR2 DIMM x 2
IDE
Initiatives de contrôle environnementales,
Fente PCI Express X16
x1
Fente PCI
x2
Connecteur de disquette
x1
Connecteur IDE
x1
Chaque connector prend en charge 2 lecteurs de
disquettes
Chaque connecteur prend en charge 2 périphériques
IDE
A740G M2L+/A780LB
SPEC
Connecteur SATA
x4
Connecteur du panneau avant
x1
Chaque connecteur prend en charge 1 périphérique
SATA
Prend en charge les équipements du panneau avant
Connecteur Audio du panneau avant x1
Prend en charge la fonction audio du panneau avant
Connecteur de sortie S/PDIF
x1
Prend en charge la fonction de sortie audio numérique
Embase de ventilateur UC
x1
Embase de ventilateur système
x1
Embase d'effacement CMOS
x1
Connecteur USB
x2
Connecteur d'alimentation
x1
Alimentation électrique du ventilateur UC (avec
fonction de ventilateur intelligent)
Alimentation électrique du ventilateur système
Chaque connecteur prend en charge 2 ports USB de
panneau avant
(24 broches)
Connecteur d'alimentation
x1
(4 broches)
E/S du
panneau
arrière
Connecteur de Port d'imprimante
x1
Clavier PS/2
x1
Souris PS/2
x1
Port VGA
x1
Port LAN
x1
Port USB
x4
Fiche audio
x3
Chaque connector prend en charge 1 Port
d'imprimante
Dimension
s de la
182 mm (l) X 235 mm (H)
carte
Fonctionnal
ités
Prise en charge RAID 0 / 1 / 1+0
spéciales
Support SE Windows XP / Vista 32 / Vista 64 / 7
Biostar se réserve le droit d'ajouter ou de supprimer le
support de SE avec ou sans préavis.
33
Motherboard Manual
ITALIAN
SPECIFICA
Sockel AM2+
CPU
Processori AMD Sempron / Athlon / Athlon II /
Phenom / Phenom II
e 64 bit
Supporto di Hyper Transport 2.0
(Watt massimo: 95W)
FSB
L’architettura AMD 64 abilita la computazione 32
Supporto di HyperTransport 2.0 fino a
2 GT/s di larghezza di banda
AMD 740G (A740G M2L+)
Chipset
AMD 780L (A780LB)
AMD SB710
Interfaccia LPC (Low Pin Count)
ITE 8718F
Super I/O Fornisce le funzionalità legacy Super
I/O usate più comunemente.
Funzioni di controllo dell’ambiente:
Monitoraggio hardware
Funzione "Smart Guardian" di ITE
Alloggi DIMM DDR2 x 2
Modulo di memoria DDR2 a canale doppio
Memoria
Capacità massima della memoria 8GB
Supporto di DDR2 533 / 667 / 800
principale
Ciascun DIMM supporta DDR2
Supporto di DDR2 1066 (by AM2+/AM3 CPU)
256MB/512MB/1GB/2GB/4GB
DIMM registrati e DIMM ECC non sono supportati
Grafica
Integrata nel Chipset AMD 740G
La memoria video condivisa massima è di 512 MB
Supporto Avivo
Modalità Bus Master Ultra DMA 33 / 66 / 100 /
IDE
Controller IDE integrato
133
Supporto modalità PIO Mode 0-4
Velocità di trasferimento dei dati fino a 3 Gb/s.
SATA
Controller Serial ATA integrato
LAN
Realtek RTL 8102EL/8103EL/8106E
Supporto
audio HD
Alloggi
Compatibile specifiche SATA Versione 2.0.
Negoziazione automatica 10 / 100 Mb/s
Uscita audio 5.1 canali
ALC662
Supporto audio High-Definition (HD)
Alloggio PCI Express X16
x1
Alloggio PCI
x2
Connettori Connettore floppy
x1
Ciascun connettore supporta 2 unità Floppy
su scheda Connettore IDE
x1
Ciascun connettore supporta 2 unità IDE
x4
Ciascun connettore supporta 1 unità SATA
Connettore SATA
34
A740G M2L+/A780LB
SPECIFICA
Connettore pannello frontale
x1
Supporta i servizi del pannello frontale
Connettore audio frontale
x1
Supporta la funzione audio pannello frontale
Connettore output S/PDIF
x1
Supporta la funzione d’output audio digitale
Collettore ventolina CPU
x1
Collettore ventolina sistema
x1
Alimentazione ventolina CPU (con funzione Smart
Fan)
Alimentazione ventolina di sistema
Collettore cancellazione CMOS x1
Connettore USB
x2
Connettore alimentazione
x1
Ciascun connettore supporta 2 porte USB
pannello frontale
(24 pin)
Connettore alimentazione
x1
(4 pin)
I/O
pannello
posteriore
Dimension
i scheda
Connettore Porta stampante
x1
Tastiera PS/2
x1
Mouse PS/2
x1
Porta VGA
x1
Porta LAN
x1
Porta USB
x4
Connettore audio
x3
Ciascun connettore supporta 1 Porta stampante
182 mm (larghezza) x 235 mm
(altezza)
Caratterist
iche
Supporto RAID 0 / 1 / 1+0
speciali
Sistemi
operativi
supportati
Biostar si riserva il diritto di aggiungere o
Windows XP / Vista 32 / Vista 64 / 7 rimuovere il supporto di qualsiasi sistema
operativo senza preavviso.
35
Motherboard Manual
SPANISH
Especificación
Conector AM2+
CPU
Procesadores AMD Sempron / Athlon / Athlon II /
Phenom / Phenom II
Conjunto
de chips
Admite HyperTransport 2.0 con un ancho
de banda de hasta 2 GT/s
AMD 740G (A740G M2L+)
AMD 780L (A780LB)
AMD SB710
Interfaz de cuenta Low Pin
ITE 8718F
Súper E/S
64 bits
Soporta las tecnologías Hyper Transport 2.0
(Vatio máximo: 95W)
FSB
La arquitectura AMD 64 permite el procesado de 32 y
Le ofrece las funcionalidades heredadas
de uso más común Súper E/S.
Iniciativas de control de entorno,
Monitor hardware
Función "Guardia inteligente" de ITE
Ranuras DIMM DDR2 x 2
Módulo de memoria DDR2 de canal Doble
Memoria
Capacidad máxima de memoria de 8GB
Admite DDR2 de 533 / 667 / 800
principal
Cada DIMM admite DDR de 256MB/
Admite DDR2 de 1066 (by AM2+/AM3 CPU)
512MB/1GB/2GB/4GB
No admite DIMM registrados o DIMM compatibles con ECC
Integrados en el conjunto de chips AMD
Memoria máxima de vídeo compartida de 512 MB
740G
Admite Avivo
Gráficos
IDE
Controlador IDE integrado
SATA
Controlador ATA Serie Integrado
Red Local
Realtek RTL 8102EL/8103EL/8106E
Soporte de
sonido HD
Ranuras
Modo bus maestro Ultra DMA 33 / 66 / 100 / 133
Soporte los Modos PIO 0~4,
Tasas de transferencia de hasta 3 Gb/s.
Compatible con la versión SATA 2.0.
Negociación de 10 / 100 Mb/s
Salida de sonido de 5.1 canales
ALC662
Soporte de sonido Alta Definición
Ranura PCI Express X16
X1
Ranura PCI
X2
Conectores Conector disco flexible
X1
Cada conector soporta 2 unidades de disco flexible
en placa
Conector IDE
X1
Cada conector soporta 2 dispositivos IDE
Conector SATA
X4
Cada conector soporta 1 dispositivos SATA
Conector de panel frontal
X1
Soporta instalaciones en el panel frontal
Conector de sonido frontal
X1
Soporta funciones de sonido en el panel frontal
36
A740G M2L+/A780LB
Especificación
Conector de salida S/PDIF
X1
Soporta función de salida de sonido digital
Cabecera de ventilador de CPU
X1
Fuente de alimentación de ventilador de CPU (con
función Smart Fan)
Cabecera de ventilador de sistema X1
Cabecera de borrado de CMOS
X1
Conector USB
X2
Conector de alimentación
X1
Fuente de alimentación de ventilador de sistema
Cada conector soporta 2 puertos USB frontales
(24 patillas)
Conector de alimentación
X1
(4 patillas)
Panel
trasero de
E/S
Tamaño de
la placa
Funciones
especiales
Conector Puerto de impresora
X1
Teclado PS/2
X1
Ratón PS/2
X1
Puerto VGA
X1
Puerto de red local
X1
Puerto USB
X4
Conector de sonido
X3
182 mm. (A) X 235 Mm. (H)
Admite RAID 0 / 1 / 1+0
Soporte de
sistema
operativo
Cada conector soporta 1 Puerto de impresora
Windows XP / Vista 32 / Vista 64 / 7
Biostar se reserva el derecho de añadir o retirar el
soporte de cualquier SO con o sin aviso previo.
37
Motherboard Manual
PORTUGUESE
ESPECIFICAÇÕES
Sockel AM2+
CPU
Processadores AMDSempron / Athlon / Athlon II
/ Phenom / Phenom II
32 e 64 bits
Suporta as tecnologias Hyper Transport 2.0
(Watt máximo: 95W)
FSB
A arquitectura AMD 64 permite uma computação de
Suporta a tecnologia HyperTransport 2.0
com uma largura de banda até 2 GT/s
AMD 740G (A740G M2L+)
Chipset
AMD 780L (A780LB)
AMD SB710
Especificaç
ão Super
I/O
Memória
principal
Placa
gráfica
ITE 8718F
Interface LPC (Low Pin Count).
Proporciona as funcionalidades mais
Iniciativas para controlo do ambiente
utilizadas em termos da especificação
Monitorização do hardware
Super I/O.
Função "Smart Guardian" da ITE
Ranhuras DIMM DDR2 x 2
Módulo de memória DDR2 de canal duplo
Capacidade máxima de memória: 8 GB
Suporta módulos DDR2 533 / 667 / 800
Cada módulo DIMM suporta uma
Suporta módulos DDR2 1066 (by AM2+/AM3 CPU)
memória DDR2 de 256MB/512MB/
Os módulos DIMM registados e os DIMM ECC não são
1GB/2GB/4GB
suportados
Memória de vídeo máxima partilhada: 512 MB
Integrada no chipset AMD 740G
IDE
Controlador IDE integrado
SATA
Controlador Serial ATA integrado
LAN
Realtek RTL 8102EL/8103EL/8106E
Suporta as funções Avivo
Modo Bus master Ultra DMA 33 / 66 / 100 / 133
Suporta o modo PIO 0~4,
Velocidades de transmissão de dados até 3 Gb/s.
Compatibilidade com a especificação SATA versão 2.0.
Auto negociação de 10 / 100 Mb/s
Suporte
para áudio
de alta
Saída de áudio de 5.1 canais
ALC662
Suporta a especificação High-Definition Audio
definição
Ranhuras
Ranhura PCI Express X16
x1
Ranhura PCI
x2
Conectores Conector da unidade de disquetes x1
Cada conector suporta 2 unidades de disquetes
na placa
Cada conector suporta 2 dispositivos IDE
38
Conector IDE
x1
A740G M2L+/A780LB
ESPECIFICAÇÕES
Conector SATA
x4
Cada conector suporta 1 dispositivo SATA
Conector do painel frontal
x1
Para suporte de várias funções no painel frontal
Conector de áudio frontal
x1
Suporta a função de áudio no painel frontal
Conector de saída S/PDIF
x1
Suporta a saída de áudio digital
Conector da ventoinha da CPU
x1
Conector da ventoinha do sistema x1
Conector para limpeza do CMOS
x1
Conector USB
x2
Conector de alimentação
x1
Alimentação da ventoinha da CPU (com a função
Smart Fan)
Alimentação da ventoinha do sistema
Cada conector suporta 2 portas USB no painel frontal
(24 pinos)
Conector de alimentação
x1
(4 pinos)
Conector da para impressora
x1
Teclado PS/2
x1
Entradas/S Rato PS/2
x1
aídas no
Porta VGA
x1
painel
Porta LAN
x1
traseiro
Porta USB
x4
Tomada de áudio
x3
Tamanho
da placa
Cada conector suporta 1 Porta para impressora
182 mm (L) X 235 mm (A)
Característi
cas
Suporta as funções RAID 0 / 1 / 1+0
especiais
A Biostar reserva-se o direito de adicionar ou remover
Sistemas
operativos
suportados
Windows XP / Vista 32 / Vista 64 / 7
suporte para qualquer sistema operativo com ou sem
aviso prévio.
39
Motherboard Manual
POLISH
SPEC
Sockel AM2+
Procesor
AMD Sempron / Athlon / Athlon II / Phenom /
Phenom II Procesory
bitowe
Obsługa Hyper Transport 2.0
(Maksymalny Watt: 95W)
FSB
Architektura AMD 64 umożliwia przetwarzanie 32 i 64
Obsługa HyperTransport 2.0 o szerokości
pasma do 2 GT/s
AMD 740G (A740G M2L+)
Chipset
AMD 780L (A780LB)
AMD SB710
Pamięć
główna
Gniazda DDR2 DIMM x 2
Moduł pamięci DDR2 z trybem podwójnego kanału
Maks. wielkość pamięci 8GB
Obsługa DDR2 533 / 667 / 800
Każde gniazdo DIMM obsługuje moduły
Obsługa DDR2 1066 (by AM2+/AM3 CPU)
256MB/512MB/1GB/2GB/4GB DDR2
Brak obsługi Registered DIMM oraz ECC DIMM
Interfejs Low Pin Count
ITE 8718F
Super I/O
Funkcje kontroli warunków pracy,
Zapewnia najbardziej powszechne
Monitor H/W
funkcje Super I/O.
Funkcja ITE "Smart Guardian"
Maks. wielkość współdzielonej pamięci video wynosi
Grafika
Zintegrowana w chipsecie AMD 740G
512 MB
Obsługa Avivo
IDE
Zintegrowany kontroler IDE
SATA
Zintegrowany kontroler Serial ATA
LAN
Realtek RTL 8102EL/8103EL/8106E
Obsługa
audio HD
Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master
obsługa PIO tryb 0~4,
Transfer danych do 3 Gb/s.
Zgodność ze specyfikacją SATA w wersji 2.0.
10 / 100 Mb/s z automatyczną negocjacją szybkości
5.1 kanałowe wyjście audio
ALC662
Obsługa High-Definition Audio
Gniazdo PCI Express X16
x1
Gniazdo PCI
x2
Złącze napędu dyskietek
x1
Każde złącze obsługuje 2 napędy dyskietek
wbudowan Złącze IDE
x1
Każde złącze obsługuje 2 urządzenia IDE
e
x4
Każde złącze obsługuje 1 urządzenie SATA
Gniazda
Złącza
40
Złącze SATA
A740G M2L+/A780LB
SPEC
Złącze panela przedniego
x1
Obsługa elementów panela przedniego
Przednie złącze audio
x1
Obsługa funkcji audio na panelu przednim
Złącze wyjścia S/PDIF
x1
Obsługa funkcji cyfrowego wyjścia audio
Złącze główkowe wentylatora procesora
x1
Złącze główkowe wentylatora
Zasilanie wentylatora procesora (z funkcją Smart Fan)
Zasilanie wentylatora systemowego
systemowego x1
Złącze główkowe kasowania CMOS x1
Złącze USB
x2
Złącze zasilania (24 pinowe)
x1
Złącze zasilania (4 pinowe)
x1
Złącze Port drukarki
x1
Klawiatura PS/2
x1
Mysz PS/2
x1
Back Panel Port VGA
x1
Port LAN
x1
I/O
Wymiary
płyty
Funkcje
specjalne
Port USB
x4
Gniazdo audio
x3
operacyjne
go
przednim
Każde złącze obsługuje 1 Port drukarki
182 mm (S) X 235 mm (W)
Obsługa RAID 0 / 1 / 1+0
Obsluga
systemu
Każde złącze obsługuje 2 porty USB na panelu
Biostar zastrzega sobie prawo dodawania lub
Windows XP / Vista 32 / Vista 64 / 7
odwoływania obsługi dowolnego systemu
operacyjnego bez powiadomienia.
41
Motherboard Manual
RUSSIAN
СПЕЦ
CPU
(централь
ный
процессор
)
FSB
Набор
микросхем
Гнездо AM2+
Процессоры AMDSempron / Athlon / Athlon II /
Phenom / Phenom II
(Максимальный ватт: 95W)
Поддержка HyperTransport 2.0 с
пропускной способностью до 2 GT/s
AMD 740G (A740G M2L+)
AMD 780L (A780LB)
AMD SB710
Модуль памяти с двухканальным режимом DDR2
Основная
Максимальная ёмкость памяти 8 ГБ
память
Каждый модуль DIMM поддерживает
256МБ/512МБ/1ГБ/2ГБ/4ГБ DDR2
SATA
Локальная
сеть
Поддержка DDR2 1066 (by AM2+/AM3 CPU)
Не поддерживает зарегистрированные модули
Интерфейс с низким количеством выводов
Обеспечивает наиболее используемые
действующие функциональные
Инициативы по охране окружающей среды,
Аппаратный монитор
Функция ITE "Smart Guardian" (Интеллектуальная
возможности Super I/O.
IDE
Поддержка DDR2 533 / 667 / 800
DIMM and ECC DIMM
ITE 8718F
Графика
на 32 и 64 бит
Поддержка Hyper Transport 2.0
Слоты DDR2 DIMM x 2
Super I/O
Архитектура AMD 64 разрешать обработка данных
защита)
Встроенная в набор микросхем AMD
740G
Максимальная совместно используемая видео
память составляет 512 МБ
Поддержка Avivo
Встроенное устройство управления
Режим "хозяина" шины Ultra DMA 33 / 66 / 100 / 133
встроенными интерфейсами устройств Поддержка режима PIO 0~4,
Встроенное последовательное
скорость передачи данных до 3 гигабит/с.
устройство управления ATA
Соответствие спецификации SATA версия 2.0.
Realtek RTL 8102EL/8103EL/8106E
Автоматическое согласование 10 / 100 Мб/с
Звуковая
поддержка
жесткого
Звуковая поддержка High-Definition
ALC662
5.1канальный звуковой выход
диска
Слоты
Встроенны
й разъём
42
Слот PCI Express X16
x1
Слот PCI
x2
Разъём НГМД
x1
Разъём IDE
x1
Каждый разъём поддерживает 2 накопителя на
гибких магнитных дисках
Каждый разъём поддерживает 2 встроенных
интерфейса накопителей
A740G M2L+/A780LB
СПЕЦ
Разъём SATA
x4
Каждый разъём поддерживает 1 устройство SATA
Разъём на лицевой панели
x1
Поддержка устройств на лицевой панели
Входной звуковой разъём
x1
Поддержка звуковых функций на лицевой панели
Разъём вывода для S/PDIF
x1
Поддержка вывода цифровой звуковой функции
Контактирующее приспособление
Источник питания для вентилятора центрального
вентилятора центрального
процессора (с функцией интеллектуального
процессора
x1
Контактирующее приспособление
вентилятора системы
x1
вентилятора)
Источник питания для вентилятора системы
Открытое контактирующее
приспособление CMOS
x1
USB-разъём
x2
Разъем питания (24 вывод)
x1
Разъем питания (4 вывод)
x1
Разъём Порт подключения
x1
Клавиатура PS/2
x1
Мышь PS/2
x1
панель
Порт VGA
x1
средств
Порт LAN
x1
ввода-выв USB-порт
x4
панели
принтера
Гнездо для подключения
наушников
Размер
лицевой панели
Каждый разъём поддерживает 1 Порт подключения
принтера
Задняя
ода
Каждый разъём поддерживает 2 USB-порта на
x3
182 мм (Ш) X 235 мм (В)
Специальн
ые
техническ
ие
Поддержка RAID 0 / 1 / 1+0
характери
стики
Поддержк
а OS
Biostar сохраняет за собой право добавлять или
Windows XP / Vista 32 / Vista 64 / 7
удалять средства обеспечения для OS с или без
предварительного уведомления.
43
‫‪Motherboard Manual‬‬
‫‪ARABIC‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫‪AM2+‬ﻣﻘﺒﺲ‬
‫وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ‬
‫‪AMD Sempron / Athlon / Athlon II‬ﻣﻌﺎﻟﺠﺎت‬
‫إﺟﺮاء اﻟﻌﻤﻠﻴﺎت اﻟﺤﺎﺳﻮﺑﻴﺔ ﺑﺴﺮﻋﺔ ‪ 32‬و‪ 64‬ﺑﺖ‪AMD 64‬ﺗﻤﻜﻦ ﺗﻘﻨﻴﺔ‬
‫اﻟﻤﺮآﺰﻳﺔ‬
‫‪Phenom II / Phenom‬‬
‫و ‪Hyper Transport2.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)و‪: 95‬ﻗﺼ ﻮى واط(‬
‫اﻟﻨﺎﻗﻞ اﻷﻣﺎﻣﻲ اﻟﺠﺎﻧﺒﻲ ‪ 2 GT/s‬ﺑﺘﺮدد ﻳﺼﻞ إﻟﻰ‪HyperTransport 2.0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫)‪AMD 740G (A740G M2L+‬‬
‫ﻣﺠﻤﻮﻋﺔ اﻟﺸﺮاﺋﺢ‬
‫)‪AMD 780L (A780LB‬‬
‫‪AMD SB710‬‬
‫‪Low Pin Count Interface‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫‪Super I/O‬‬
‫‪ITE 8718F‬‬
‫وﺳﺎﺋﻞ اﻟﺘﺤﻜﻢ ﻓﻲ اﻟﺒﻴﺌﺔ‪:‬‬
‫اﻷآﺜﺮ اﺳﺘﺨﺪاﻣًﺎ‪Super I/O .‬ﺗﻮﻓﺮ وﻇﻴﻔﺔ‬
‫ﻣﺮاﻗﺐ ﻟﻤﻌﺮﻓﺔ ﺣﺎﻟﺔ اﻷﺟﻬﺰة‬
‫‪ ITE‬ﻣﻦ "‪"Smart Guardian‬وﻇﻴﻔﺔ‬
‫ﻓﺘﺤﺔ ‪DDR2 DIMM‬‬
‫ﻋﺪد‪2‬‬
‫ﺳﻌﺔ ذاآﺮة ﻗﺼﻮى ‪ 8‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‬
‫اﻟﺬاآﺮة اﻟﺮﺋﻴﺴﻴﺔ‬
‫ﻣﻴﺠﺎ ‪ 256/512‬ﺳﻌﺔ ‪ DDR2‬ﺗﺪﻋﻢ ذاآﺮة ﻣﻦ ﻧﻮع ‪DIMM‬ﺗﺪﻋﻢ آﻞ ﻓﺘﺤﺔ‬
‫ﺑﺎﻳﺖ و‪ /1‬و‪ /2‬و‪ 4‬ﺟﻴﺠﺎ ﺑﺎﻳﺖ‬
‫ﺳﻌﺎت ‪ 800 / 667 / 533‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻧﻮع‬
‫ﺳﻌﺎت ‪ 1066‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪DDR2‬ﺗﺪﻋﻢ اﻟﺬاآﺮة ﻣﻦ ﻧﻮع‬
‫)‪(DDR2 1066 is by AM2+/AM3 CPU‬‬
‫‪ ECC‬وﺗﻠﻚ اﻟﺘﻲ ﻻ ﺗﺘﻮاﻓﻖ ﻣﻊ ‪DIMM‬ﻻ ﺗﺪﻋﻢ رﻗﺎﺋﻖ اﻟﺬاآﺮة‬
‫ﻣﻴﺠﺎ ﺑﺎﻳﺖ‪512‬أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ‬
‫ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻣﺎت‬
‫‪ AMD 740G‬ﻣﺪﻣﺠﺔ ﻓﻲ رﻗﺎﺋﻖ‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫ﻣﺘﻜﺎﻣﻞ‪IDE‬ﻣﺘﺤﻜﻢ‬
‫‪SATA‬‬
‫ﻣﺘﻜﺎﻣﻞ‪Serial ATA‬ﻣﺘﺤﻜﻢ‬
‫ﺷﺒﻜﺔ داﺧﻠﻴﺔ‬
‫‪Realtek RTL 8102EL/8103EL/8106E‬‬
‫دﻋﻢ اﻟﺼﻮت ﻋﺎﻟﻲ‬
‫ﻣﺰدوﺟﺔ اﻟﻘﻨﺎة‪DDR2‬وﺣﺪة ذاآﺮة‬
‫‪Avivo‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫وﺿﻊ رﺋﻴﺴﻲ‪Ultra DMA 33 / 66 / 100 / 133‬ﻧﺎﻗﻞ ﺑﺘﻘﻨﻴﺔ‬
‫‪PIO Mode 0~4‬دﻋﻢ وﺿﻊ‬
‫ﺟﻴﺠﺎﺑﺖ‪/‬ﺛﺎﻧﻴﺔ‪3.‬ﻧﻘﻞ اﻟﺒﻴﺎﻧﺎت ﺑﺴﺮﻋﺎت ﺗﺼﻞ إﻟﻰ‬
‫‪ 2.0.‬اﻹﺻﺪار ‪SATA‬ﻣﻄﺎﺑﻘﺔ ﻟﻤﻮاﺻﻔﺎت‬
‫ﺗﻔﺎوض ﺗﻠﻘﺎﺋﻲ ‪ 100/10‬ﻣﻴﺠﺎ ﺑﺎﻳﺖ ‪ /‬ﺛﺎﻧﻴﺔ‬
‫ﻗﻨﻮات ﻟﺨﺮج اﻟﺼﻮت‪5.1‬‬
‫‪ALC662‬‬
‫اﻟﺘﻌﺮﻳﻒ‬
‫ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ اﻟﺼﻮت ﻋﺎﻟﻲ اﻟﺘﻌﺮﻳﻒ ﻣﻦ‬
‫ﻓﺘﺤﺔ ‪PCI Express x16‬‬
‫ﻋﺪد ‪1‬‬
‫ﻓﺘﺤﺔ ‪PCI‬‬
‫ﻋﺪد‪2‬‬
‫اﻟﻤﻨﺎﻓﺬ ﻋﻠﻰ ﺳﻄﺢ‬
‫ﻣﻨﻔﺬ ﻣﺤﺮك أﻗﺮاص ﻣﺮﻧﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﻣﺤﺮآﻴﻦ ﻟﻸﻗﺮاص اﻟﻤﺮﻧﺔ‬
‫اﻟﻠﻮﺣﺔ‬
‫ﻣﻨﻔﺬ ‪IDE‬‬
‫ﻋﺪد ‪1‬‬
‫‪IDE‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ اﺛﻨﻴﻦ ﻣﻦ أﺟﻬﺰة‬
‫ﻣﻨﻔﺬ ‪SATA‬‬
‫ﻋﺪد‪4‬‬
‫‪SATA‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ واﺣﺪ ﻣﻦ أﺟﻬﺰة‬
‫اﻟﻔﺘﺤﺎت‬
‫‪44‬‬
‫‪A740G M2L+/A780LB‬‬
‫اﻟﻤﻮاﺻﻔﺎت‬
‫ﻣﻨﻔﺬ اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ ﺗﺠﻬﻴﺰات اﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ اﻟﺼﻮت اﻷﻣﺎﻣﻲ‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ اﻟﺼﻮت ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‬
‫ﻣﻨﻔﺬ ﺧﺮج ‪S/PDIF‬‬
‫ﻋﺪد ‪1‬‬
‫ﻳﺪﻋﻢ وﻇﻴﻔﺔ ﺧﺮج اﻟﺼﻮت اﻟﺮﻗﻤﻲ‬
‫وﺻﻠﺔ ﻣﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ اﻟﻤﺮآﺰﻳﺔ‬
‫ﻋﺪد ‪1‬‬
‫‪Smart Fan‬ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ ﻣﻊ وﻇﻴﻔﺔ‬
‫وﺻﻠﺔ ﻣﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫ﻋﺪد ‪1‬‬
‫ﻟﺘﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ ﻟﻤﺮوﺣﺔ اﻟﻨﻈﺎم‬
‫وﺻﻠﺔ ﻣﺴﺢ ‪CMOS‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ‪USB‬‬
‫ﻋﺪد ‪2‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪24‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﺗﻮﺻﻴﻞ اﻟﻄﺎﻗﺔ )‪4‬دﺑﻮس(‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﻔﺬ ﻃﺎﺑﻌﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻟﻮﺣﺔ ﻣﻔﺎﺗﻴﺢ ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﺎوس ‪PS/2‬‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ دﺧﻞ‪/‬ﺧﺮج‬
‫ﻣﻨﻔﺬ ‪VGA‬‬
‫ﻋﺪد ‪1‬‬
‫اﻟﻠﻮﺣﺔ اﻟﺨﻠﻔﻴﺔ‬
‫ﻣﻨﻔﺬ ﺷﺒﻜﺔ اﺗﺼﺎل ﻣﺤﻠﻴﺔ‬
‫ﻋﺪد ‪1‬‬
‫ﻣﻨﺎﻓﺬ ‪USB‬‬
‫ﻋﺪد‪4‬‬
‫ﻣﻘﺒﺲ ﺻﻮت‬
‫ﻋﺪ‪3‬‬
‫ﺣﺠﻢ اﻟﻠﻮﺣﺔ‬
‫‪ 182‬ﻣﻢ )ﻋﺮض( ‪ 235 X‬ﻣﻢ )ارﺗﻔﺎع(‬
‫ﻣﺰاﻳﺎ ﺧﺎﺻﺔ‬
‫‪RAID 0 / 1 / 1+0‬ﺗﺪﻋﻢ ﺗﻘﻨﻴﺔ‬
‫دﻋﻢ أﻧﻈﻤﺔ اﻟﺘﺸﻐﻴﻞ‬
‫‪Windows XP / Vista 32 / Vista 64 / 7‬‬
‫‪45‬‬
‫ﺑﺎﻟﻠﻮﺣﺔ اﻷﻣﺎﻣﻴﺔ‪USB‬ﻳﺪﻋﻢ آﻞ ﻣﻨﻔﺬ ﻓﺘﺤﺘﻲ‬
‫ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻧﻈﺎم ﺗﺸﻐﻴﻞ ﺑﺈﺧﻄﺎر أو ‪Biostar‬ﺗﺤﺘﻔﻆ‬
‫ﺑﺪون إﺧﻄﺎر‪.‬‬
Motherboard Manual
JAPANESE
仕様
AMD 64アーキテクチャでは、32ビットと64ビット計算が可
Sockel AM2+
CPU
FSB
AMD Sempron / Athlon / Athlon II / Phenom / 能です
Phenom II プロセッサ
ハイパートランスポート2.0とクールアンドクワイアットを
(最高のワット: 95W)
サポートします
2 GT/sのバンド幅までハイパートランスポー
ト2.0をサポートします
AMD 740G (A740G M2L+)
チップセッ
ト
AMD 780L (A780LB)
AMD SB710
DDR2 DIMMスロット x 2
デュアル チャンネルモードDDR2メモリモジュール
メインメモ
最大メモリ容量8GB
DDR2 533 / 667 / 800 をサポート
リ
各DIMMは 256MB/512MB/1GB/2GB/4GB DDR2 1066 をサポート (by AM2+/AM3 CPU)
DDR2をサポート
登録済みDIMMとECC DIMMはサポートされません
低ピンカウントインターフェイス
ITE 8718F
Super I/O
もっとも一般に使用されるレガシーSuper I/O
機能を採用しています。
グラフィッ
H/Wモニター
ITEの「スマートガーディアン」機能
最大の共有ビデオメモリは512MBです
AMD 740Gチップセットに統合
Avivo のサポート
クス
Ultra DMA 33 / 66 / 100 / 133バスマスタモード
IDE
統合IDEコントローラ
SATA
統合シリアルATAコントローラ
LAN
Realtek RTL 8102EL/8103EL/8106E
PIO Mode 0~4のサポート、
最高3Gb/秒のデータ転送速度
SATAバージョン2.0仕様に準拠。
10 / 100 Mb/秒のオートネゴシエーション
HDオーディ
オのサポー
環境コントロールイニシアチブ、
5.1チャンネルオーディオアウト
ALC662
ハイデフィニションオーディオのサポート
ト
PCI Express X16スロット
x1
PCIスロット
x2
オンボード
フロッピーコネクタ
x1
各コネクタは2つのフロッピードライブをサポートします
コネクタ
IDEコネクタ
x1
各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ
x4
各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ
x1
フロントパネル機能をサポートします
スロット
46
A740G M2L+/A780LB
仕様
フロントオーディオコネクタ
x1
フロントパネルオーディオ機能をサポートします
S/PDIFアウトコネクタ
x1
デジタルオーディオアウト機能をサポートします
CPUファンヘッダ
x1
CPUファン電源装置(スマートファン機能を搭載)
システムファンヘッダ
x1
システムファン電源装置
CMOSクリアヘッダ
x1
USBコネクタ
x2
各コネクタは2つのフロントパネルUSBポートをサポートし
ます
電源コネクタ(24ピン)
x1
電源コネクタ(4ピン)
x1
プリンタポートコネクタ
x1
PS/2キーボード
x1
PS/2マウス
x1
背面パネル
VGAポート
x1
I/O
LANポート
x1
USBポート
x4
オーディオジャック
x3
ボードサイ
各コネクタは1つのプリンタポートをサポートします
182 mm (幅) X 235 mm (高さ)
ズ
特殊機能
RAID 0 / 1 / 1+0 のサポート
OSサポート Windows XP / Vista 32 / Vista 64 / 7
Biostarは事前のサポートなしにOSサポートを追加または削
除する権利を留保します。
2013/10/08
47