Bosch DIP-3040-00N Installation manual

DIVAR IP 3000
DIP-3040-00N, DIP-3042-2HD, DIP-3042-4HD
en
Installation Manual
DIVAR IP 3000
Table of Contents | en
3
Table of contents
1
Safety precautions
4
1.1
General safety precautions
4
1.2
Electrical safety precautions
5
1.3
ESD precautions
6
1.4
Operating precautions
6
2
System overview
7
2.1
Chassis features
7
2.2
Chassis components
7
2.2.1
Chassis
7
2.2.2
Backplane
7
2.2.3
Power supply
8
2.3
Device views
8
2.3.1
LED description - front panel
2.3.2
LAN port LED description - rear panel
10
3
Chassis setup and maintenance
11
3.1
Removing hard drive trays
11
3.2
Installing a hard drive
11
4
System setup - first steps
12
4.1
Introduction
12
4.2
Setup instruction
12
4.3
Starting the application
12
4.4
Using Bosch VMS Configuration Wizard
13
4.5
Using Bosch VMS Configuration Client
24
4.6
Using Bosch VMS Operator Client
25
5
Recovering the unit
26
6
Additional Documentation and client software
27
Bosch Sicherheitssysteme GmbH
9
Installation Manual
2013.09 | V2 | DOC
4
en | Safety precautions
DIVAR IP 3000
Safety precautions
1
Observe the safety precautions in this chapter.
1.1
General safety precautions
Follow these rules to ensure general safety:
–
Keep the area around the system clean and free of clutter.
–
Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won't accidentally be stepped on.
–
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
–
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
Warning!
Interruption of mains supply:
!
Voltage is applied as soon as the mains plug is inserted into the mains socket.
However, for devices with a mains switch, the device is only ready for operation when the
mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the
socket, the supply of power to the device is completely interrupted.
Warning!
Removing the housing:
!
To avoid electric shock, the housing must only be removed by qualified service personnel.
Before removing the housing, the plug must always be removed from the mains socket and
remain disconnected while the housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any repairs.
Warning!
Power cable and AC adapter:
!
When installing the product, use the provided or designated connection cables, power cables
and AC adaptors. Using any other cables and adaptors could cause a malfunction or a fire.
Electrical Appliance and Material Safety Law prohibits the use of UL or CSA-certified cables
(that have UL/CSA shown on the code) for any other electrical devices.
Warning!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty
!
batteries with batteries of the same type or a similar type recommended by the manufacturer.
Handle used batteries carefully. Do not damage the battery in any way. A damaged battery
may release hazardous materials into the environment.
Dispose of empty batteries according to the manufacturer's instructions.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
Safety precautions | en
5
Warning!
!
Handling of lead solder materials used in this product may expose you to lead, a chemical
known to the State of California to cause birth defects and other reproductive harm.
Notice!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried
out correctly.
When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands
must be worn and the ESD safety precautions observed.
Notice!
Installation should only be carried out by qualified customer service personnel in accordance
with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using highquality materials and components that can be reused.
This symbol means that electronic and electrical devices that have reached
the end of their working life must be disposed of separately from
household waste.
In the EU, separate collecting systems are already in place for used
electrical and electronic products. Please dispose of these devices at your
local communal waste collection point or at a recycling center.
1.2
Electrical safety precautions
Basic electrical safety precautions should be followed to protect you from harm and the
system from damage:
–
Be aware of the locations of the power on/off switch on the chassis as well as the room's
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
–
Do not work alone when working with high voltage components.
–
Power should always be disconnected from the system when removing or installing main
system components, such as the motherboard or memory modules. When disconnecting
power, you should first turn off the system and then unplug the power cords from all the
power supply modules in the system.
–
When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power if necessary.
–
Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
–
The power supply power cords must include a grounding plug and must be plugged into
grounded electrical outlets. The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical shock.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
6
en | Safety precautions
–
DIVAR IP 3000
Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature
Coefficient) fuses on the mainboard must be replaced by trained service technicians only.
The new fuse must be the same or equivalent as the one replaced. Contact technical
support for details and support.
Caution!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside
!
down, which will reverse its polarities. This battery must be replaced only with the same or
an equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries
according to the manufacturer's instructions.
1.3
ESD precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is made
to protect your equipment from ESD:
–
Do not use mats designed to decrease electrostatic discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
–
Use a grounded wrist strap designed to prevent static discharge.
–
Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
for use.
–
–
Touch a grounded metal object before removing the board from the antistatic bag.
Do not let components or printed circuit boards come into contact with your clothing,
which may retain a charge even if you are wearing a wrist strap.
–
Handle a board by its edges only. Do not touch its components, peripheral chips, memory
modules or contacts.
–
When handling chips or modules, avoid touching their pins.
–
Put the mainboard and peripherals back into their antistatic bags when not in use.
–
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and the
mainboard.
1.4
Operating precautions
The chassis cover must be in place when the system is operating to assure proper cooling. Out
of warranty damage to the system can occur if this practice is not strictly followed.
Note:
Please handle used batteries carefully. Do not damage the battery in any way. A damaged
battery may release hazardous materials into the environment. Do not discard a used battery
in the garbage or a public landfill. Please comply with the regulations set up by your local
hazardous waste management agency to dispose of your used battery properly.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System overview | en
7
System overview
2
The DIVAR IP 3000 system is an affordable and easy to use all-in-one recording, viewing, and
management solution for network surveillance systems of up to 32 channels. All channels are
pre-licensed. Running the full Bosch VMS solution and powered by Bosch VRM (Video
Recording Manager) including the Video Streaming Gateway to integrate 3rd party cameras,
DIVAR IP 3000 is an intelligent IP storage device that eliminates the need for separate NVR
(Network Video Recorder) server and storage hardware.
DIVAR IP 3000 is a 4-bay mini tower unit that combines advanced management and state-ofthe-art recording management into a single cost-effective, plug and play IP recording appliance
for IT-minded customers which are seeking for a state-of-the-art “second generation” DVR and
NVR recording solution.
Easy to install and operate, DIVAR IP 3000 features wizard-based set-up and centralized
configuration to reduce installation times. All components are pre-installed and preconfigured. Simply connect to the network and turn on the unit — DIVAR IP 3000 is ready to
begin recording straight out of the box.
Bosch Video Management System manages all IP and digital video and audio, plus all the
security data being transmitted across your IP network. It seamlessly combines IP cameras
and encoders, provides system-wide event and alarm management, system health monitoring,
user and priority management.
DIVAR IP 3000 features front-swappable SATA-II hard drives providing up to 8 TB of gross
storage capacity. All system software is pre-installed and pre-activated — creating an out-ofthe-box ready-to-use video management appliance. DIVAR IP 3000 utilizes Windows Storage
Server 2008 R2 operating system.
2.1
Chassis features
The chassis includes the following features:
–
CPU (Intel i3 processor)
–
4 slots for SATA drives (front replaceable)
–
1x VGA output (onboard)
–
1x DVI graphics output
–
4x USB 2.0, 1x USB 3.0
–
1x internal USB Transcoder device
–
1x Gigabit Ethernet LAN port
Chassis components
2.2
This chapter describes the most common components included with your chassis.
2.2.1
Chassis
The chassis includes 4 slots for hard drives.
2.2.2
Backplane
The backplane accepts front-swappable SATA-II hard drives providing up to 8 TB of gross
storage capacity.
Warning!
!
Use caution when servicing and working around the backplane. Hazardous voltage or energy
is present on the backplane when the system is operating. Do not touch the backplane with
any metal objects and make sure no ribbon cables touch the backplane.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
8
en | System overview
2.2.3
DIVAR IP 3000
Power supply
The chassis features a highly energy-efficient power supplies.
2.3
Device views
There are several LEDs on the front and rear of the chassis. The LEDs show the over-all status
of the system and the activity and health of specific components.
Front view:
1
6
2
2013.09 | V2 | DOC
3
4
5
1
Lock for front cover
4
LAN activity LED
2
Power on/off LED
5
System status LED
3
Hard disk access LED
6
Individual hard disk LED
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System overview | en
9
Rear view:
1
2
3
5
4
6
7
1
1x VGA (monitor)
5
Mains connection 100 - 240 VAC
2
1x Ethernet (RJ45)
6
1x USB 3.0
Note: Do not use this port for
keyboard and mouse.
3
4
4x USB 2.0
7
1x DVI (monitor), for local viewing
Note: Use these ports for keyboard
Note:
and mouse connection.
If the system is only connected to the
DVI port, no video signal is displayed
1x eSATA for data export
Note: Do not connect hard disk drives
for recording.
until the system has started
completely. This can take 1 – 2
minutes. A video signal is always
displayed when the monitor is
connected to the VGA port.
2.3.1
LED description - front panel
This chapter describes the LED displays on the front of the chassis.
LED indicator
Power LED
Bosch Sicherheitssysteme GmbH
LED color
LED state
Description
N/A
Off
Power off
Blue
On (default)
Working (S0 state)
Installation Manual
2013.09 | V2 | DOC
10
en | System overview
DIVAR IP 3000
LED indicator
HDD LED
LAN LED
System LED
LED color
LED state
Description
N/A
Off
No disk access
Blue
Blinking
Disk access
N/A
Off
Network disconnected
Blue
On
Network connected
Blue
Blinking
Network activity
N/A
Off
Power off
Blue
On (default)
System has booted in normal operation.
Blue
Blinking
System is booting or shutting down
Red
On
Critical event occurred, such as degraded
RAID volume.
Bosch also provides the API and then
application program is able to control this
status.
Individual hard
disk LED
N/A
Off (default)
Hard drive not present.
Blue
On
Hard drive present.
Red
On
Bosch provides the API to let application
program to control this status.
2.3.2
LAN port LED description - rear panel
This chapter describes the LAN port LED on the rear of the chassis.
LAN connector:
1
2
Nr.
1
LED indicator
RJ45 LED
(left)
2
RJ45 LED
(right)
2013.09 | V2 | DOC
LED color
LED state
NIC state
N/A
Off
No connection or 10 Mb/s
Green
On
100 Mb/s
Yellow
On
1000 Mb/s
Yellow
On
Active connection
Yellow
Blinking
Transmit or receive activity
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
3
Chassis setup and maintenance | en
11
Chassis setup and maintenance
This chapter covers the steps required to install components and perform maintenance on the
chassis.
Caution!
!
Review the warnings and precautions listed in the manual before setting up or servicing this
chassis.
See also:
Safety precautions, page 4
3.1
Removing hard drive trays
The drives are mounted in drive carriers to simplify their installation and removal from the
chassis. These carriers also help promote proper airflow for the drive bays.
To remove hard drive trays from the chassis:
1. Turn off the system.
2.
Press the release button on the drive carrier. This extends the drive carrier handle.
3.
Use the handle to pull the drive carrier with the drive out of the chassis.
4.
Insert the drive carrier with the new drive into the chassis bay, making sure that the drive
carrier handle is completely closed.
Notice!
Except for short periods of time, do not operate the unit with the hard drives removed from
the bays.
3.2
Installing a hard drive
The drives are mounted in drive carriers.
To install a hard drive to the hard drive carrier:
1. Remove the drive from the carrier.
2.
Install a new drive into the carrier with the printed circuit board side facing down so that
the mounting holes align with those in the carrier.
3.
Replace the drive carrier into the chassis bay, making sure that the drive carrier handle is
completely closed.
Notice!
We recommend using the respective Bosch hard disk drives. The hard disk drives as one of
the critical component are carefully selected by Bosch based on available failure rates. HDD –
not delivered from Bosch – are not supported. Information on supported HDDs can be found
in the datasheet in the Bosch Online Product Catalog.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
12
en | System setup - first steps
4
DIVAR IP 3000
System setup - first steps
The following installation directive provides information on Installation and Configuration.
DIVAR IP systems are based on Windows Storage Server 2008 R2 operating system.
This chapter is valid for DIVAR IP models that come with pre-installed hard drives. Empty units
start into the DOM recovery menu on first start.
See also:
–
Recovering the unit, page 26
4.1
Introduction
DIVAR IP systems are shipped with a pre-installed Configuration Wizard from factory.
4.2
Setup instruction
All DIVAR IP systems are preconfigured with a default IP address and with default iSCSI
settings.
–
IP Address: 192.168.0.200
–
Subnet mask: 255.255.255.0
Observe the following:
–
DIVAR IP needs to have an active network link during installation. Make sure that the
network switch you are connecting to is powered on.
–
The default IP address must not be occupied by any other device in the network.
–
Determine whether the initial installation is on a DHCP network. If not then you must
assign valid IP addresses to the video devices. Consult the local IT administrator to obtain
a valid IP address range to be used with DIVAR IP and associated devices.
–
The default iSCSI settings are optimized for use with VRM.
User with administrator rights:
–
User: BVRAdmin
–
Password: WSS4Bosch
Notice!
We strongly recommended not changing the user settings. Changing the user settings can
result in malfunctioning of the system.
4.3
Starting the application
DIVAR IP system is ready to go out of the box. The application provides a simple to install and
intuitive to use solution for network surveillance systems.
To start the application:
1. Connect the unit and the cameras to the network.
2.
Turn on the unit.
The Windows Storage Server 2008 R2 setup process starts.
3.
Select the appropriate language for the installation, then click Next.
4.
In the Country or region, Time and currency and Keyboard layout lists, click the
appropriate item, then click Next.
The Microsoft Software License Terms and the EULA (End User License Agreement) are
displayed.
2013.09 | V2 | DOC
5.
Accept the license terms, then click Start. Windows restarts.
6.
After restart is finished, press CTR+ALT+DELETE. The Windows logon page is displayed.
7.
Enter the default password WSS4Bosch.
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
8.
13
After entering the password, a message is displayed that you must change the password
before logging on the first time. To confirm, click OK.
9.
Change the password.
A series of scripts perform important setup tasks. This can take several minutes. Do not
turn off the computer.
A page is displayed where you can perform initial Windows configuration tasks.
Note: In case of password loss a system recovery must be performed as described in the
installation manual. The configuration must be done from scratch or must be imported.
10. Click the Set time zone, Configure networking and Provide computer name and domain
link, enter the appropriate information, then click Close. Windows restarts.
11. Press CTR+ALT+DELETE. The Windows logon page is displayed.
12. Enter the password.
The Bosch VMS default screen is displayed.
13. Double-click the Bosch VMS Wizard icon
to start the Configuration Wizard.
The Welcome page is displayed.
14. Configure the system using the Configuration Wizard.
Notice!
If the IP addresses of devices that should be added fall within the same IP range as the DIVAR
IP, you can use the Configuration Wizard. In all other cases we recommend using the
Bosch VMS Configuration Client.
Notice!
To perform administrative tasks, the BVRAdmin account can be entered when Bosch VMS
default screen is displayed. To do so, press CTRL+ALT+DEL, then hold down SHIFT while
clicking the Switch User option.
See also:
–
Using Bosch VMS Configuration Wizard, page 13
4.4
–
Using Bosch VMS Configuration Client, page 24
–
Recovering the unit, page 26
Using Bosch VMS Configuration Wizard
Intended use for Configuration Wizard is the quick and easy configuration of a smaller system.
Configuration Wizard helps you to achieve a configured system including VRM, iSCSI system,
cameras, recording profiles and user groups.
User groups and their permissions are configured automatically. You can add or remove users
and set passwords.
Configuration Wizard can access Management Server only on the local computer.
You can save an activated configuration for backup purposes and import this configuration
later. You can change this imported configuration after import.
Configuration Wizard adds the local VRM automatically.
Restrictions:
The following tasks cannot be done with the Configuration Wizard. Use Bosch VMS
Configuration Client instead.
–
adding additional license packages
–
adjusting schedules
–
configuring systems with no or multiple VRM
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
14
en | System setup - first steps
DIVAR IP 3000
–
configuring external storage devices
–
all advanced configurations beyond a basic setup (maps or alarms, for example)
For these tasks refer to the Bosch VMS manual (see Additional Documentation and client
software, page 27):
To achieve a quick configuration using the Configuration Wizard:
1.
On the Bosch VMS default screen, double-click the Bosch VMS Wizard icon. The
Welcome page is displayed.
2.
Run-through the following pages of the wizard.
Welcome page
If the connection to the Management Server cannot be established, a corresponding error
message is displayed. You cannot continue working with Configuration Wizard.
If VRM is not available on the computer, a corresponding error message is displayed. You
cannot continue working with Configuration Wizard.
If the license check fails, a corresponding error message is displayed. You cannot continue
working with Configuration Wizard.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
15
Network settings page
You configure the network settings of the operating system.
As soon as you click Next button, the settings are activated.
If you have changed any setting on this page, click Reboot to restart the system.
Notice!
If a DHCP server is employed in the network for the dynamic assignment of IP addresses,
activate acceptance of IP addresses automatically assigned to the device.
Certain applications (VRM, Bosch Video Management System, Bosch Video Client,
Configuration Manager) use the IP address for the unique assignment of the device. If using
these applications, the DHCP server must support the fixed assignment between IP address
and MAC address, and must be appropriately set up so that, once an IP address is assigned, it
is retained each time the system is rebooted.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
16
en | System setup - first steps
DIVAR IP 3000
Time settings page
You configure the time settings of the operating system.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
17
Video settings page
This page displays the devices and services that are included in the latest saved configuration.
You can import a configuration.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
18
en | System setup - first steps
DIVAR IP 3000
Device selection page
This page displays all video devices that are not included in the latest saved configuration.
Deselect the devices that should not be added to the configuration, then click Next.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
19
Device passwords page
This page is used to authenticate password protected devices. This can either be done for all
cameras at once (if passwords are identical) or for each camera individually. Configuration
Client must be used in order to set or change device passwords.
Password check is performed automatically, when you do not enter a character in a password
field for a few seconds or you click outside the password field.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
20
en | System setup - first steps
DIVAR IP 3000
Recording profile page
For different profile assignments to different cameras you must execute Configuration Wizard
multiple times.
Note:
Before selecting a recording profile observe the following:
–
Recording profile details
All video devices use the default recording profile details.
To change these use the Bosch VMS Configuration Client.
–
Stream quality settings
All video devices use the default settings for Stream 1 to record.
To change these use the Bosch VMS Configuration Client.
–
2013.09 | V2 | DOC
Schedule
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
21
The default schedule is used for all recording profiles.
The Day schedule is active from 8 a.m. until 6 p.m., Monday through Friday.
The Night schedule is active from 6 p.m. until 8 a.m., Monday through Friday.
The Weekend schedule is active 24 hours a day for Saturday and Sunday.
To change the schedule use the Bosch VMS Configuration Client.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
22
en | System setup - first steps
DIVAR IP 3000
Add storage page
This page allows the addition of additional iSCSI storage devices
For limitations, refer to the datasheet available in the online catalog.
Notice!
If the wizard stops and the message appears, that the internal iSCSI storage is not ready for
recording because the LUNs are not formatted, you must format the LUNs using Bosch VMS
Configuration Client.
To format the LUNs, see Bosch VMS Configuration Manual, Chapter Formatting a LUN.
2013.09 | V2 | DOC
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
23
User accounts page
You can add users and passwords. Use Configuration Client to add user groups and to change
permissions.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
24
en | System setup - first steps
DIVAR IP 3000
Finish configuration page
After clicking Save and activate the configuration is activated.
After successful activation the Activate Configuration page is displayed again. Now you can
store a backup of the configuration if desired: Click Save backup copy.
4.5
Using Bosch VMS Configuration Client
If the IP addresses of devices that should be added do not fall within the same IP range as the
DIVAR IP, we recommend using the Bosch VMS Configuration Client.
To assign device IP addresses:
1.
On the Bosch VMS default screen, double-click the Configuration Client icon
to
change device network settings. The application starts.
2.
Enter the following, then click OK.
User name: admin
Password: no password required (if not set with the wizard)
Connection: 127.0.0.1
3.
On the Hardware menu, click Initial Device Scan.
The application performs a network scan for all defaulted devices.
4.
To assign all devices at once, click Select All, then right-click the selected devices, then
click SetIP Addresses. The Set IP Addresses dialog box is displayed.
Note:
It is also possible to configure the devices individually with specific IP addresses based
on MAC address.
5.
Enter the starting IP address for the address range you want to use, click the Calculate
tab, then click OK.
2013.09 | V2 | DOC
6.
To restart the devices, click OK.
7.
Close Configuration Client .
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
System setup - first steps | en
25
To perform further functionalities refer to the Bosch VMS manual. References to the manual
are described in Additional Documentation and client software, page 27.
4.6
Using Bosch VMS Operator Client
Use Bosch VMS Operator Client to verify the live, recording and playback functionality of
DIVAR IP.
To verify live image functionality in the Operator Client
1.
On the Bosch VMS default screen, double-click the Operator Client icon
2.
Enter the following and click OK.
. The
application starts.
User name: admin
Password: no password required (if not set with the wizard)
Connection: 127.0.0.1
3.
Click the live image icon. The Logical Tree with the cameras is displayed.
4.
Select a camera and drag it to an image window. The image of the camera is displayed if
the camera is assigned correctly.
Note:
Cameras in the image window with a red dot in the camera’s icon are viewed live.
To verify recording functionality in the Operator Client
4 Cameras in the Logical Tree with a red dot in the camera’s icon are recording.
To verify playback functionality in the Operator Client
4 The time line moves if the a camera is viewed in playback mode.
Performance overview live:
4CIF
2.5 Mbit
5 Mbit
10 Mbit
17
13
8
Number of software monitors
720p
2.5 Mbit
5 Mbit
10 Mbit
12
10
5
Number of software monitors
1080p
2.5 Mbit
5 Mbit
10 Mbit
6
5
3
Number of software monitors
To perform further functionalities refer to the Bosch VMS manual. References to the manual
are described in Additional Documentation and client software, page 27.
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
26
en | Recovering the unit
5
DIVAR IP 3000
Recovering the unit
Following procedure describes how to restore the factory default image.
To restore the unit to factory default image
1. Start the unit and press F7 during the BIOS power-on-self-test.
The Recovery menu is displayed.
Notice!
Make sure that a VGA monitor, a keyboard and a mouse are connected to the unit.
2.
Select one of the following:
–
Initial to factory image (all data will be deleted)
(restores to factory default image and deletes all data on the HDDs)
or
–
Restore to Factory image (all data will not be deleted)
(restores to factory default image; data on the HDDs will not be deleted)
Note:
Windows performs the setup. The screen displays the percentage of the process.
Notice!
Do not turn off the unit during the process. This will damage the Recovery media.
3.
The unit starts from the Recovery media. If the setup is successfull. press Yes to restart
the system.
4.
Windows performs the initial setup of the operating system. The unit restarts after
Windows has completed the setup.
5.
After the restart of the unit, the factory default settings are installed and the Windows
logon screen is displayed.
The factory default settings are:
2013.09 | V2 | DOC
–
IP address: 192.168.0.200
–
Subnet mask: 255.255.255.0
–
User: BVRAdmin
–
Password: WSS4Bosch
Installation Manual
Bosch Sicherheitssysteme GmbH
DIVAR IP 3000
6
Additional Documentation and client software | en
27
Additional Documentation and client software
Documentation for Bosch Security System products can be found as follows:
4 www.boschsecurity.com > select your region and your country > select Product Catalog >
start a search for your product > select the product in the search results to show the
existing documents.
And on the following network share:
4
\\<IP address of DIVAR IP>\sources
Bosch Sicherheitssysteme GmbH
Installation Manual
2013.09 | V2 | DOC
Bosch Sicherheitssysteme GmbH
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Sicherheitssysteme GmbH, 2013