8160 D/8190 D
8260 D/8290 D
8360 D/8390 D
8361 D/8391 D
Cooker Hood
Campana extractora
Exaustor
Operating and Installation Instructions
Instrucciones de montaje y manejo
Manual de Instruções
Contents
Safety warnings ................................................................................ 3
For the user ........................................................................................ 3
For the installer ................................................................................... 3
.............................................................................................................
Description of the Appliance ........................................................... 5
Extractor version ................................................................................ 5
Filter Version ...................................................................................... 5
Control Panel - 8160 D - 8190 D - 8260 D - 8290 D .......................... 6
Control Panel - 8360 D - 8390 D - 8361 D - 8391 D .......................... 7
Maintenance and care ...................................................................... 8
Cleaning the hood .............................................................................. 8
Metal grease filter ............................................................................... 8
Removing the metal grease filter ........................................................ 8
Charcoal filter ..................................................................................... 9
Changing the light bulb ..................................................................... 10
What to do if ................................................................................... 11
Special accessories ....................................................................... 12
Technical assistance service ......................................................... 12
Technical Details ............................................................................ 13
Mounting accessories included .................................................... 12
Electrical connection ......................................................................... 65
Wall unit mounting ............................................................................ 66
Printed on recycled paper
AEG - putting words into action
2
Safety warnings
For the user
• The cooker hood is designed to extract unpleasant odours from the
kitchen, it will not extract steam.
• Always cover lighted elements, to prevent excess heat from
damaging the appliance. In the case of oil, gas and coal fired
cookers it is essential to avoid open flames.
• Also, when frying, keep the deep frying pan on the cooker top/
cooker under careful control.
• The hot oil in the frying pan might ignite due to overheating.
• The risk of self-ignition increases when the oil being used is dirty.
• It is extremely important to note that overheating can cause a fire.
• Never carry out any flambé cooking under the hood.
• Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch
off the automatic circuit breaker).
• It is very important to clean the hood and replace the filter at
the recommended intervals. Failure to do so could cause
grease deposits to build up, resulting in a fire hazard.
• The appliance is not intended for use by young children or infirm
persons without supervision.
• Young children should be supervised to ensure that they do not play
with the appliance.
• WARNING - Ensure that the appliance is switched off before
replacing the lamp to avoid the possibility of electric shock.
For the installer
• When used as an extractor unit, the hood must be fitted with a
150mm diameter hose.
• Should there already be a pipe of diameter 125 or 120 mm that
ducts to the outside through the walls or roof, it is possible to use
the 150/125-120 mm reduction flange provided.
In this case the hood will be slightly noisier.
• When installing the hood, make sure you respect the following
minimum distance from the top edge of the cooking hob/ring
surfaces:
electric cookers
500 mm
gas cookers
650 mm
coal and oil cookers
700 mm min.
3
• The national Standard on fuel-burning systems specifies a maximum depression of 0.04 mbar in such rooms.
• The air outlet must not be connected to chimney flues or combustion gas ducts. The air outlet must under no circumstances be
connected to ventilation ducts for rooms in which fuel-burning
appliances are installed.
• The air outlet installation must comply with the regulations laid down
by the relevant authorities.
• When the unit is used in its extractor version, a sufficiently large
ventilation hole must be provided, with dimensions that are approximately the same as the outlet hole.
• National and regional building regulations impose a number of
restrictions on using hoods and fuel-burning appliances connected
to a chimney, such as coal or oil room-heaters and gas fires, in the
same room.
• Hoods can only be used safely with appliances connected to a
chimney if the room and/or flat (air/environment combination) is
ventilated from outside using a suitable ventilation hole approximately 500-600 cm2 large to avoid the possibility of a depression
being created during operation of the hood.
• If you have any doubts, contact the relevant controlling authority or
building inspector’s office.
• Since the rule for rooms with fuel burning appliances is “outlet hole
of the same size as the ventilation hole”, a hole of 500-600 cm2,
which is to say a larger hole, could reduce the performance of the
extractor hood.
• If the hood is used in its filtering function, it will operate simply and
safely in the above conditions without the need for any of the
aforementioned measures.
• When the hood is used in its extractor function, the following rules
must be followed to obtain optimal operation:
— short and straight outlet hose
— keep bends in outlet hose to a minimum
— never install the hoses with an acute angle, they must always
follow a gentle curve.
— keep the hose as large as possible (preferably the same diameter as the outlet hole).
• Failure to observe these basic instructions will drastically reduce the
performance and increase the noise levels of the extractor hood.
4
Description of the Appliance
• The hood is supplied as an extractor unit and
can also be used with a filtering function
by fitting one charcoal filter.
• You will need an original AEG charcoal
filter for this function (Available from your
local AEG Service Force Centre).
Extractor version
• In this version fumes are extracted to the
outside via a hose connected to the
coupling ring A. Fig. 1.
Fig. 1
• In order to obtain the best performance
the hose should have a diameter equal
to the outlet hole.
• Should there already be a pipe of diameter 125 mm that ducts to
the outside through the walls or roof, it is possible to use the 150/
125 mm reduction flange provided. In this case the hood will be
slightly noisier.
Filter Version
• The air is filtered through an charcoal filter and returned to the
kitchen through the top grill of the outlet pipe.
• You will need an original AEG charcoal filter for the filtering function.
(See Special Accessories).
• Fix the deflector using 2 screws Ø 2,9x13 mm. Fig. 2.
• Optionally, the position of the chimney
elements can be changed.
When using the hood in the filter
version the chimney must be fixed at
the top, with the air outlet grill at the
side.
Fig. 2
5
Control Panel
• Best results are obtained by using a low speed for normal
conditions and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking, you will
then get an under pressure in the kitchen. The hood should be left
on after cooking for about 15 minutes or until all the odours have
disappeared. The control switches are located on the unit’s front
panel:
8160 D - 8190 D
• the light switch switches the hood lamp on and off
• the motor switch switches the motor on and off, enabling you to
select one of the three different speeds.
Motor switch
Light switch
8260 D - 8290 D
•
•
•
•
•
the light switch switches the hood lamp on and off
the motor switch switches the motor off
Speed 1: Speed 1 push-button
Speed 2: Speed 2 push-button
Speed 3: Speed 3 push-button
Light switch
Motor switch
6
Speed 3
Speed 1
Speed 2
Control Panel
8360 D - 8361 D - 8390 D - 8391 D
• Best results are obtained by using a low speed for normal
conditions and a high speed when odours are more concentrated.
Turn the hood on a few minutes before you start cooking, you will
then get an under pressure in the kitchen. The hood should be left
on after cooking for about 15 minutes or until all the odours have
disappeared. The control switches are located on the unit’s front
panel:
A
B
C
D
E
F
G
-
Mains switch, OFF.
Start and choice of motor speed 1-2-3-1-2.........
Indicates speed 1 (LED).
Indicates speed 2 (LED)
Indicates speed 3 (LED)
Indicates Intensive speed (LED).
Intensive speed on/off. The Intensive speed runs for 5 minutes:
If the hood is on when the Intensive speed is activated, the hood
reverts to previous speed after 5 minutes.
If the hood is off when the Intensive speed is activated, the hood
will be turned off after 5 minutes.
To interrupt the Intensive speed, press button A or B.
H - Light ON/OFF
Should the hood or the controls fail to operate: disconnect the power
supply for at least 5 seconds, then turn the hood back on again.
7
Maintenance and care
• The hood must always be disconnected from the electricity
supply before beginning any maintenance work.
Cleaning the hood
• Clean the outside of the hood using a damp cloth and a mild detergent.
• Never use corrosive, abrasive or flammable cleaning products.
• Never insert pointed objects in the motor’s protective grid.
• Wash the outside surfaces using a delicate detergent solution.
Never use caustic detergents or abrasive brushes or powders.
• Only ever clean the switch panel and filter grille using a damp cloth
and delicate detergents.
• It is extremely important to clean the unit and change the filters at
the recommended intervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
Metal grease filter
• The purpose of the grease filters is to absorb grease particles which
form during cooking and it must always be used, either in the
external extraction or internal recycling function.
Attention: the metal grease filters must be removed and washed,
either by hand or in the dishwasher, every four weeks.
Removing the metal grease filter
8
• First, push the metal grease filter stop backwards, then extract the
filter, pulling downwards. Fig. 3.
Hand washing
Soak grease filters for about one hour in hot water with a little
washing-up liquid, then rinse off
thoroughly with hot water. Repeat the
process if necessary. Refit the grease
filters when they are dry.
Dishwasher
Place grease filters in the
dishwasher. Select most
powerful washing
programme and highest
temperature, at least 65°C.
Repeat the process. Refit
Fig. 3
the grease filters when
they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
on its performance.
• Clean the inner housing using a hot detergent solution only (never
use caustic detergents, abrasive powders or brushes).
Charcoal filter
• The charcoal filter should only be used if you want to use the hood
in the recirculation function.
• To do this you will need an original AEG charcoal filter (available
from your local Service Force Centre).
• Cleaning/replacing the carbon filter
Unlike other carbon filters, the LONGLIFE carbon filter can be cleaned
and reactivated. At normal use the filter should be cleaned every
second month (when using the hood 2,5 hours per day, in avarage).
The best way to clean the filter is in the dishwasher. Use normal
detergent and choose the highest temperature (65º C). Wash the filter
separately so that no food parts gets stuck on the filter and later
causes bad odours. To reactivate the carbon, the filter should be dried
in an oven for 10 minutes with a temperature of maximum 100º C.
After approximately three years of use, the carbon filter should be
replaced with a new, as the odour reduction capacity will be
reduced.
• Mounting - Fig. 4
Put the charcoal filter frame in place and fix it with 5 screws.
Fit the charcoal filter first from the rear side and fix it frontwards
using the two red keys A.
Fig. 4
• To remove proceed in the reverse order.
• Always specify the hood model code number and serial number
when ordering replacement filters. This information is shown on the
registration plate located on the inside of the unit.
• The charcoal filter can be ordered from your local AEG Service
Force Centre.
9
Warning
• Failure to observe the instructions on cleaning the unit and
changing the filters will cause a fire hazard. You are therefore
strongly recommended to follow these instructions.
• The manufacturer declines all responsibility for any damage to the
motor or any fire damage linked to inappropriate maintenance or
failure to observe the above safety recommendations.
Changing the light bulb
• Disconnect the cooker hood from the main supply.
8160 D - 8190 D
• Remove the lamp cover. Fig. 5.
• Replace the old bulb with a new
one of the same type.
• Remount the lamp cover.
1
2
8260 D - 8290 D - 8360 D - 8390 D 8361 D - 8391 D
• Press (1) the lamp cover (2) and
open it. Fig. 6.
• Replace the old bulb with a new
one of the same type (3).
• Close the lamp cover.
Fig. 5
3
• If the light does not come on,
make sure the bulb has been
inserted correctly before
contacting your local Service
Force Centre.
10
1
2
Fig. 6
What to do if
If your appliance fails to work properly please carry out the following
checks.
Symptom
Solution
The cooker hood will not start...
Check that:
The hood is connected to
the electricity supply.
Check that a fan speed has
been selected
The cooker hood is not working
effectively..
Check that:
The fan speed is set high
enough for the task.
The grease filters are clean.
The kitchen is adequately vented
to allow the entry of fresh air.
If set up for recirculation, check
that the charcoal filter is still
effective.
If set up for extraction, check that
the ducting and outlets are not
blocked.
The cooker hood has
switched off during operation...
The safety cut-out device has been
tripped.
Turn off the hob and then wait for
the device to reset.
If the hood has been installed
below the heights indicated in the
installation instructions the motor
will cut-out frequently which will
damage the hood.
If after all these checks, the problem persists, contact your local
Service Force Centre, quoting the model and serial number.
Please note that it will be necessary to provide proof of purchase for
any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have
been made as the engineer will make a charge if the fault is not a
mechanical or electrical breakdown.
11
Special accessories
Charcoal KF8
E-Nr. 942 118 648
Technical assistance service (not for UK)
You are welcome to telephone our technical assistance service (see list
of technical assistance centres) whenever you need information or in
the unlikely event of a fault.
For service in Australia call 1300 650 020.
When calling, please be ready to specify:
1. The model code number
2. The serial number (E-Nr.)
3. The manufacturing number (F-Nr.)
This information is shown on the registration plate inside the unit
behind the grease filter.
We reserve the right to change specifications and colours as a result of
our policy of continuing technological development.
Service and spare parts for UK
In the event of your appliance requiring service, or if you wish to
purchase spare parts, contact your local AEG Service Force Centre by
telephoning: 08705 929 929
Your telephone call will be automatically routed to the Service Centre
covering your post code area. For the address of your local Service
Force Centre and further information about Service Force, please visit
the website at www.serviceforce.co.uk
Please ensure that you have read the section „What to do if....“ as the
engineer will make a charge if the fault is not a mechanical or electrical breakdown even the appliance is under warranty. Please note that
proof of purchase is required for in-guarantee service calls.
Help us to help you
Please determine your type of enquiry before writing or telephoning.
When you contact us we need to know:
•
•
•
Your name
Address and post code
Telephone number
• Clear and concise details of the fault
• Name and model of the appliance*
• E number*
* This information can be found on the rating plate, which can be seen
when the grease filters are removed.
12
Technical Details
Models
Dimensions (in cm)
Maximum
Motor
Height Width Depth absorbed power power
Lighting
Length Electrical
of the cable connection
8160 D 80-135 59,8
47
170 W
1 x 155 W 1 x 11 W (PL)
150 cm
220-240 V
8190 D 82-137 89,8
48
170 W
1 x 155 W
150 cm
220-240 V
8260 D 80-135 59,8
47
200 W
1 x 155 W 2 x 20 W (G4) 150 cm
220-240 V
8290 D 82-137 89,8
48
200 W
1 x 155 W 2 x 20 W (G4) 150 cm
220-240 V
8360 D 80-135 59,8
47
175 W
1 x 130 W 2 x 20 W (G4) 150 cm
220-240 V
8390 D 82-137 89,8
48
175 W
1 x 130 W 2 x 20 W (G4) 150 cm
220-240 V
8361 D 80-135 59,8
47
175 W
1 x 130 W 2 x 20 W (G4) 150 cm
220-240 V
8391 D 82-137 89,8
48
175 W
1 x 130 W 2 x 20 W (G4) 150 cm
220-240 V
1 x 11 W
Mounting accessories included
6 wall plugs Ø 8 mm (brick fixing only)
6 wood-screws 5 x 45 mm
2 metal screws 2,9 x 13
4 metal screws 2,9 x 6,5
5 metal screws 3,5 x 13
2 hooks
1 chimney support
2 clamps
1 deflector
1 reduction flange Ø 150-125 mm
1 charcoal filter frame
1 allen spanner
13
Electrical connection (not for UK)
Safety warnings for the electrician
Before connecting the appliance to the power supply, check that the
voltage indicated on the rating plate corresponds to the mains power
supply available. Appliances fitted with a plug can be connected to
any standard power socket within easy access.
Should it be necessary to provide a fixed connection, the hood must
only be installed by an electrician authorised by the local electricity
board. When installing, an omnipolar disconnector with a distance of
at least 3 mm between contacts must be provided.
Fixed connection of the appliance must only be carried out by an
authorised electrician.
Electrical connection for UK only
Safety warnings for the electrician
Connect the hood to the mains supply via a double pole switch
which has 3 mm minimum separation between the contacts.
The switch must be accessible at all times.
The following is valid in the United Kingdom only:
- the wire which is coloured green and yellow must be connected to
the terminal which is marked with the letter E or by the earth symbol
), or coloured green or green and yellow;
(
- the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, - the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.
14
Wall unit mounting - Fig. 7
• Position the template on the wall (1) and mark the position, and drill
(2) the holes (2 x Ø 8 mm).
• Mount the two wall plugs with the hooks (3).
• Hang the hood on the hooks and level it with the adjustment screws
(4).
• Remove the grease filters (5) and mark for the two screws (6).
Remove the hood and drill the holes (2 x Ø 8 mm).
Insert the rawl plugs (7) and hang the hood on the wall again. Adjust
it with the screws (8) and secure it with the screws (9).
• Mount the chimney support (10) with the wall plugs (9) and the
screws (11). Be careful that it is centered over the hood and
horizontally aligned.
• Extractor version (S): Connect a tube between the hood air outlet
and the wall or roof exhaust channel. Fix it with the tube clamps
supplied.
Filter version (K): Mount the deflector with the two screws supplied
(2,9x13 mm) (13).
• Make the electrical connection (14) (see previous page)
• Place the chimney (15) and fix it to the top chimney support with the
two screws (16) supplied (2,9x6,5 mm). Lower the bottom part of
the chimney (17) and fasten it to the top of the hood with two
screws, supplied (18) (2,9x6,5 mm).
15
Electric hob
Gas hob
Fig. 7
16
500 mm
650 mm
Exhaust tube
Power outlet
Electric hob
Gas hob
500 mm
650 mm
22
240
Wall bracket
270
370
8190 D
8290 D
8390 D
8391 D
350
8160 D
8260 D
8360 D
8361 D
599-899
Electric hob
Gas hob
500 mm
650 mm
17
From the Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen,
cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators,
cookers, washing machines,vacuum cleaners, chain saws and lawn mowers) are sold each
year to a value of approx. USD 14 billion in more than 150 countries around the world.
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
http://www.aeg.co.uk
© Copyright by AEG
LI13FC ed. 02/03