D-Link DES-818 - Switch User manual

Table of Contents
Table of Contents
Product Overview......................................................... 4
Package Contents.................................................... 4
System Requirements.............................................. 4
Introduction............................................................... 5
Features................................................................... 6
Hardware Overview.................................................. 7
Connections........................................................ 7
LEDs................................................................... 8
Wireless Installation Considerations....................... 10
Seven Configuration Operation Modes.................... 11
Access Point Mode................................................. 11
Wireless Client Mode.............................................. 12
Repeater Mode....................................................... 13
Bridge Mode........................................................... 14
Bridge with AP Mode.............................................. 15
WISP Client Router mode...................................... 16
WISP Repeater mode............................................. 17
Configuration.............................................................. 18
Web-based Configuration Utility............................. 18
Setup Wizard.......................................................... 19
Setup Wizard for AP Mode..................................... 20
Setup Wizard for Repeater Mode........................... 27
Setup Wizard for Wireless Client Mode.................. 35
Add Wireless Device With WPS............................. 43
D-Link DAP-1360 User Manual
Wireless Setup ...................................................... 45
Access Point..................................................... 45
Repeater........................................................... 47
Wireless Client.................................................. 48
Bridge .............................................................. 49
Bridge with AP.................................................. 50
WISP Client Router and WISP Repeater.......... 51
WAN Settings......................................................... 52
Dynamic IP (DHCP).......................................... 52
Static IP............................................................ 53
PPPoE.............................................................. 54
PPTP................................................................ 55
LAN Setup........................................................ 56
LAN Settings..................................................... 57
Advanced................................................................ 58
Advanced Wireless........................................... 58
Access Control.................................................. 59
User Limit.......................................................... 60
Port Forwarding................................................ 61
Port Filter.......................................................... 62
DMZ.................................................................. 63
Parental Control................................................ 64
Advanced Network............................................ 65
Maintenance........................................................... 66
Device Administration ...................................... 66
Save and Restore ............................................ 66
2
Table of Contents
Firmware . ........................................................ 67
Watchdog (Ping of Life).................................... 68
Time.................................................................. 69
Schedules......................................................... 70
Status..................................................................... 71
Device Info........................................................ 71
Log.................................................................... 72
Statistics........................................................... 73
Wireless............................................................ 73
Networking Basics..................................................... 95
Technical Specifications........................................... 97
Help.............................................................................. 74
Wireless Security....................................................... 75
What is WEP? ....................................................... 75
Configure WEP....................................................... 76
What is WPA?........................................................ 77
Configure WPA-PSK, WPA2-PSK, and WPA2-AutoPSK (Personal) ...................................................... 78
Configure WPA-EAP, WPA2-EAP, and WPA2-AutoEAP (Enterprise)..................................................... 79
Connect to a Wireless Network ............................................80
Using Windows® XP.............................................. 80
Using Windows® Vista (Secured Network)............ 82
Using Windows® Vista (Unsecured Network) ....... 85
Troubleshooting...............................................................88
Wireless Basics ......................................................... 90
Wireless Modes.......................................................... 94
D-Link DAP-1360 User Manual
3
Section 1 - Product Overview
Product
PackageOverview
Contents
Your DAP-1360 package should contain the following items. If any of the items are missing, please contact
your reseller.
• D-Link DAP-1360 Wireless N Access Point
• Power Supply
• Manual on CD
• Quick Installation Guide
• Ethernet Cable
WARNING: Using a power supply with a different voltage rating
than the one included with the DAP-1360 will cause
damage and void the warranty for this product.
System Requirements
To configure this device, you will need the following:
•A computer equipped with an Ethernet interface and operating under Windows Vista, XP or 2000,
Mac OS 10.X or above, or Linux
•Internet Explorer or Netscape Navigator version 6.0 or above, with JavaScript enabled
D-Link DAP-1360 User Manual
4
Section 1 - Product Overview
Introduction
D-Link, an industry leader in networking, introduces the new D-Link Wireless N Access Point(DAP-1360). With the
ability to transfer files with a maximum wireless signal rate of up to 300Mbps1, the DAP-1360 gives you high-speed
wireless network access for your home or office.
The DAP-1360 is Wi-Fi IEEE 802.11n compliant, meaning that it can connect and interoperate with other 802.11n
compatible wireless client devices. The DAP-1360 is also backwards compatible with 802.11b/g. It can be flexibly
configured to operate in 7 different modes Access Point, Wireless Client, Bridge, Bridge with AP, Repeater, WISP
Client Router or WISP Repeater.With its Setup Wizard, the DAP-1360 Access Point ensures that you will be up and
running on a wireless network in just a matter of minutes.
The DAP-1360 Access Point features Wi-Fi Protected Access (WPA-PSK/WPA2-PSK) and 64/128-bit WEP Encryption
to provide an enhanced level of security for wireless data communications. The DAP-1360 also includes additional
security features to keep your wireless connection safe from unauthorized access.
The DAP-1360 supports WPS on the AP, repeater and wireless client operation modes,with each capable of being
conveniently set up by using the PIN method or Push Button.
1 Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction,
and network overhead, lower actual data throughput rate.
D-Link DAP-1360 User Manual
5
Section 1 - Product Overview
Features
•Connects homes and small offices to a high-speed wireless network - This AP provides better wireless signals
for your computers than earlier generation wireless 802.11g technology. Adding this wireless AP to your home and
office provides an excellent solution for doing everyday activities such as transferring files, browsing the Internet, and
downloading music. This AP uses Intelligent Antenna technology to transmit multiple streams of data, which enable
you to receive wireless signals in the farthest corners of your home or office. Not only does it extend your wireless
range, it also works with your existing 802.11g devices.
•Multiple operation modes – The AP can be flexibly configured to operate as an Access Point, Wireless Client,
Bridge, Bridge with AP, Repeater, WISP Client Router or WISP Repeater.
•Total security – Complete set of security features including WEP encryption and WPA/WPA2 to protect network
against outside intruders.
•WPS (Wi-Fi Protected Setup) - This AP supports WPS in the AP, Repeater and Wireless Client operation
modes.
•Protect wireless network and data – The DAP-1360 provides 64/128-bit WEP encryption and WPA/WPA2 security
to protect your network and wireless data. In addition, it also provides MAC address filtering and the Disable SSID
Broadcast function to limit outsiders’ access to your home and office network.
•Easy to install and use – With D-Link's Setup Wizard, you can set up your wireless network in minutes. It configures
your DAP-1360's operation mode, makes it easy to add new wireless devices onto the network, and helps you create
a simple wireless network for your home and office.
*M
aximum wireless signal rate based on IEEE Standard 802.11n specifications. Actual data throughput will vary. Network conditions and environmental
factors, including volume of network traffic, building materials and construction, and network overhead lower actual data throughput rate.
D-Link DAP-1360 User Manual
6
Section 1 - Product Overview
Hardware Overview
Connections
LAN Port:
Connects to an Ethernet-enabled
device such as a computer,
switch or router.
Power Socket:
Connects to the power
adapter.
D-Link DAP-1360 User Manual
RESET:
Restores the access point’s
configuration to its original
factory default settings.
7
Section 1 - Product Overview
Hardware Overview
LEDs
LAN: A blinking green
condition indicates data is
being transferred through
the LAN port; a solid green
condition indicates the LAN
port connection is OK.
Power: A solid green
condition indicates
the device has been
successfully connected
to a power source.
WLAN: A blinking green condition
indicates wireless activity is
taking place; a solid green
condition indicates wireless
connections are OK.
D-Link DAP-1360 User Manual
Security: A solid green
condition indicates
wireless security has been
enabled.
8
Section 1 - Product Overview
LEDs
WPS LED: A solid light
indicates a successful
WPS connection. A
blinking light indicates
the device is trying to
establish a connection.
D-Link DAP-1360 User Manual
9
Section 2 - Wireless Installation
Wireless Installation Considerations
The D-Link wireless access point lets you access your network using a wireless connection from virtually anywhere
within the operating range of your wireless network. Keep in mind, however, that the number, thickness and location
of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range. Typical ranges vary
depending on the types of materials and background RF (radio frequency) noise in your home or business. The key
to maximizing wireless range is to follow these basic guidelines:
1. Keep the number of walls and ceilings between the D-Link access point and other network devices to a
minimum - each wall or ceiling can reduce your adapter’s range from 3-90 feet (1-30 meters.) Position your
devices so that the number of walls or ceilings is minimized.
2. Be aware of the direct line between network devices. A wall that is 1.5 feet thick (.5 meters), at a 45-degree
angle appears to be almost 3 feet (1 meter) thick. At a 2-degree angle it looks over 42 feet (14 meters)
thick! Position devices so that the signal will travel straight through a wall or ceiling (instead of at an angle)
for better reception.
3. Building Materials make a difference. A solid metal door or aluminum studs may have a negative effect
on range. Try to position access points, wireless access points, and computers so that the signal passes
through drywall or open doorways. Materials and objects such as glass, steel, metal, walls with insulation,
water (fish tanks), mirrors, file cabinets, brick, and concrete will degrade your wireless signal.
4. Keep your product away (at least 3-6 feet or 1-2 meters) from electrical devices or appliances that generate
RF noise.
5. If you are using 2.4GHz cordless phones or X-10 (wireless products such as ceiling fans, lights, and home
security systems), your wireless connection may degrade dramatically or drop completely. Make sure your
2.4GHz phone base is as far away from your wireless devices as possible. The base transmits a signal
even if the phone in not in use.
D-Link DAP-1360 User Manual
10
Section 2 - Wireless Installation
Seven Configuration Operation Modes
How your AP will operate depends on which operation mode you select. This section will help you figure out which
setting works for different requirements.
Access Point Mode
In the Access Point mode, the DAP-1360 acts as a central connection point for any computer (client) that has a 802.11n
or backward-compatible 802.11b/g wireless network interface and is within range of the AP. Clients must use the same
SSID (wireless network name) and channel as the AP in order to connect. If wireless security is enabled on the AP,
the client will need to enter a password to connect to the AP. In the Access Point mode, multiple clients can connect
to the AP at the same time.
Wireless PCs Using the DAP-1360 as a Central Connection Point
D-Link DAP-1360 User Manual
11
Section 2 - Wireless Installation
Wireless Client Mode
In the Wireless Client mode, the DAP-1360 acts as a wireless network adapter for your Ethernet-enabled device (such
as a game console or a TV set-top box). Connect your Ethernet-enabled device to the AP using an Ethernet cable. The
AP Client mode can support multiple wired clients. If you are going to connect several Ethernet-enabled devices to your
DAP-1360, connect the LAN port of the DAP-1360 to an Ethernet switch, then connect your devices to this switch.
Ethernet-enabled Gaming Console Using the DAP-1360 as a Wireless Interface to Access the Internet
D-Link DAP-1360 User Manual
12
Section 2 - Wireless Installation
Repeater Mode
In the Repeater mode, the DAP-1360 increases the range of your wireless network by extending the wireless coverage
of another AP or wireless router. The APs and wireless router (if used) must be within range of each other. Make sure
that all clients, APs, and the wireless router all use the same SSID (wireless network name) and channel.
Extending the Wireless Coverage of a Wireless Router Using the DAP-1360
D-Link DAP-1360 User Manual
13
Section 2 - Wireless Installation
Bridge Mode
In the Bridge mode, the DAP-1360 wirelessly connects seperate LANs that can’t easily be connected together with a
cable. For example, if there are two wired LANs separated by a small courtyard, it would be expensive to bury cables
to connect between the two sides together. A better solution is to use two DAP-1360 units to wirelessly connect the
two LANs. In the Bridge mode, both DAP-1360 units do not act as APs.
Note: The Bridge mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two DAP-1360
units. Communication with other APs (even other D-Link APs) is not guaranteed.
LAN 1
LAN 2
Connecting Two Separate LANs Together Through Two DAP-1360 Units
(Wireless PCs Cannot Access the DAP-1360 Units)
D-Link DAP-1360 User Manual
14
Section 2 - Wireless Installation
Bridge with AP Mode
The Bridge with AP mode is the same as the Bridge mode, but in this case, the DAP-1360 also acts as an AP. Clients
with wireless interfaces can wirelessly connect to the DAP-1360 and then connect to the other LAN that the DAP-1360
bridges to.
Note: The Bridge with AP mode is not specified in the Wi-Fi or IEEE standards. This mode will only work using two
DAP-1360 units. Communication with other APs (even other D-Link APs) is not guaranteed.
LAN 1
LAN 2
Connecting Two Separate LANs Together Through Two DAP-1360 Units
(Wireless PCs Can Access the DAP-1360 Units)
D-Link DAP-1360 User Manual
15
Section 2 - Wireless Installation
WISP Client Router Mode
In the WISP Client Router mode, the DAP-1360 wirelessly connects to a WISP (Wireless Internet Service Provider) AP.
In this mode, the DAP-1360 also acts as a router for wired clients on your LAN and provides NAT (Network Address
Translation) and a DHCP server to generate IP addresses for wired clients only. NAT and the DHCP server allow many
computers to share the same wireless Internet connection.
If you are a WISP subscriber and want to access your WISP account using wired computers, connect your computers
to the DAP-1360 to get NAT, and then connect them to the WISP AP.
Connecting Wired PCs to the Internet Using the DAP-1360
D-Link DAP-1360 User Manual
16
Section 2 - Wireless Installation
WISP Repeater Mode
In the WISP Repeater mode, the DAP-1360 wirelessly connects to a WISP (Wireless Internet Service Provider) AP. In
this mode, the DAP-1360 also acts as a router for both wireless and wired clients on your LAN. The WISP Repeater
mode provides NAT (Network Address Translation) and a DHCP server to generate IP addresses for both wireless
and wired clients. NAT and the DHCP server allow many computers to share the same wireless Internet connection.
If you are a WISP subscriber and want to use your WISP account in your house, but the signals from the outdoor WISP
AP are not strong enough to reach all of the areas in the house, use the DAP-1360 to can extend the signals from the
outdoor WISP AP and provide access to wireless clients in your house. Using this mode, wireless as well as wired
clients can connect to the outdoor WISP AP through the DAP-1360.
Connecting Wired and Wireless PCs to the Internet Using the DAP-1360
D-Link DAP-1360 User Manual
17
Section 3 - Configuration
Configuration
Web-based Configuration Utility
If you wish to change the default settings or optimize the performance of the DAP-1360, you may use the configuration
utility that D-Link has included a configuration utility for this purpose.
After you have completed the initial installation, you can access the configuration menu, at any time, by opening the
web-browser and typing in the device name of the DAP-1360. The DAP-1360’s default device name is shown below:
1. Open the web browser
2. Type in the device
name (dlinkap) or ip
address (192.168.0.50)
of the DAP-1360.
Note: If you have changed the default device name assigned to the DAP-1360, make sure to enter the correct device name.
3. Type admin in the User Name
field
4. Leave the Password blank
5. Click OK
D-Link DAP-1360 User Manual
18
Section 3 - Configuration
Setup Wizard
Click Launch Wireless Setup Wizard to quickly
configure your access point.
To setup your wireless network using WPS, you can
click Add Wireless Device With WPS and skip to page
43.
D-Link DAP-1360 User Manual
19
Section 3 - Configuration
Setup Wizard for AP Mode
This Wizard is designed to assist you in connecting you wireless device to your access point. It will guide you through
step-by-step instructions on how to get your wireless device connected.
Click Launch Wireless Setup Wizard to begin.
Click Launch Wireless Setup Wizard
Select the wireless mode Access Point.
D-Link DAP-1360 User Manual
20
Section 3 - Configuration
Enter the Device Name of the AP and click Next to
continue. It is recommended to change the Device
Name if there is more than one D-Link device within
the subnet.
If you want to change the admin account password,
enter a new password and click Next.
Select Auto as the configuration method only if your
wireless device supports Wi-Fi Protected Setup.
Skip to next page for Manual configuration.
Click Next to continue.
D-Link DAP-1360 User Manual
21
Section 3 - Configuration
Click Save to save your network settings.
In order for your network settings to take effect AP will
reboot automatically.
When the device has finished rebooting the main screen
will display.
Select Manual as the configuration method to setup
your network manually.
Click Next to continue.
D-Link DAP-1360 User Manual
22
Section 3 - Configuration
Enter a network name and choose Automatically
assign a network key.
To Manually assign a network key, skip this step.
Click Next to continue.
If you choose WPA-PSK encryption, the following
screen will show you your Network Key to enter on your
wireless clients.
Click Save to finish the Setup Wizard.
D-Link DAP-1360 User Manual
23
Section 3 - Configuration
If you choose WEP encryption, the following screen will
show you your Network Key to enter on your wireless
clients.
Click Save to finish the Setup Wizard.
Choose Manually assign a network key to create
your own key.
Click Next to continue.
D-Link DAP-1360 User Manual
24
Section 3 - Configuration
For WPA encryption, enter a Network Key between 8
and 63 characters long or enter exactly 64 characters
using 0-9 and A-F.
Click Next to continue.
If you select WPA encryption, the following screen will
show you your network key to enter on your wireless
clients.
Click Save to finish the Setup Wizard.
D-Link DAP-1360 User Manual
25
Section 3 - Configuration
For WEP encryption, enter a Network Key exactly 5 or
13 characters long or exactly 10 or 26 characters using
0-9 and A-F.
Click Next to continue.
If you select WEP encryption, the following screen will
show you your network key to enter on your wireless
clients.
Click Save to finish the Setup Wizard.
D-Link DAP-1360 User Manual
26
Section 3 - Configuration
Setup Wizard for Repeater Mode
This wizard is designed to assist you in configuring the wireless settings for your DAP-1360 with repeater mode. It
will guide you through step-by-step instructions on how to setup your wireless network. You can click launch wireless
setup wizard to quickly configure your access point. If DAP-1360 successfully connect to the AP or Wireless router
with repeater mode, you can also click add wireless device with WPS to setup your wireless network using WPS.
Click Launch Wireless Setup Wizard to begin.
Click Launch Wireless Setup Wizard
Select the wireless mode Repeater.
D-Link DAP-1360 User Manual
27
Section 3 - Configuration
Enter the Device Name of the AP and click Next to
continue. It is recommended to change the Device
Name if there is more than one D-Link device within
the subnet.
If you want to change the admin account password,
enter a new password and click Next.
D-Link DAP-1360 User Manual
28
Section 3 - Configuration
Select Auto configuration if you want to use Wi-Fi
Protected Setup.
If you want to setup your network manually, skip this
step.
Click Next to continue.
Select PIN to connect your wireless device with WPS.
For PBC configuration, skip to next page.
Enter the PIN number used into your access point and
click Connect.
D-Link DAP-1360 User Manual
29
Section 3 - Configuration
Start WPS on the wireless device you are adding to
your wireless network to complete the setup.
Select PBC to use the Push Button Configuration to
connect to your network.
Click Connect to continue.
D-Link DAP-1360 User Manual
30
Section 3 - Configuration
Press down the Push Button on the wireless device you
are adding to your network to complete the setup.
Select Manual configuration to setup your network
manually.
Click Next to continue.
D-Link DAP-1360 User Manual
31
Section 3 - Configuration
If you clicked on Site Survey to following screen will
be displayed.
Find your access point from the list and click Connect
to complete the Setup Wizard.
Choose which Security Mode you want to use and click
Next to continue.
D-Link DAP-1360 User Manual
32
Section 3 - Configuration
If you choose WEP, enter the wireless security password
and click Next to complete the Setup Wizard.
If you choose WPA, enter the WPA Personal Passphrase
and click Next to complete the Setup Wizard.
D-Link DAP-1360 User Manual
33
Section 3 - Configuration
If you choose WPA2, enter the WPA2 Personal
Passphrase and click Next to complete the Setup
Wizard.
The Wireless Setup Wizard is complete.
Click Finish to reboot the device.
D-Link DAP-1360 User Manual
34
Section 3 - Configuration
Setup Wizard for Wireless Client Mode
To configure the wireless client mode, follow these instructions.
Click Launch Wireless Setup Wizard to begin.
Click Launch Wireless Setup Wizard
Select the wireless mode Wireless Client.
D-Link DAP-1360 User Manual
35
Section 3 - Configuration
Enter the Device Name of the AP and click Next to
continue. It is recommended to change the Device
Name if there is more than one D-Link device within
the subnet.
If you want to change the admin account password,
enter a new password and click Next.
D-Link DAP-1360 User Manual
36
Section 3 - Configuration
Select Auto Configuration if you want to use Wi-Fi
Protected Setup.
If you want to setup your network manually, skip this
step.
Click Next to continue.
Select PIN to connect your wireless device with WPS.
For PBC configuration, skip to next page.
Enter the PIN number used into you access point and
click Connect.
D-Link DAP-1360 User Manual
37
Section 3 - Configuration
Start WPS on the wireless device you are adding to you
wireless network to complete the setup.
Select PBC to use the Push Button Configuration to
connect to your network.
Click Connect to continue.
D-Link DAP-1360 User Manual
38
Section 3 - Configuration
Press down the Push Button on the wireless device you
are adding to your network to complete the setup.
Select Manual configuration to setup your network
manually.
Click Next to continue.
D-Link DAP-1360 User Manual
39
Section 3 - Configuration
Enter the Wireless Network Name of the AP or use
site survey to find the AP.
Click Next to continue.
If you clicked on Site Survey, the following screen will
be displayed.
Find your access point from the list and click Connect
to complete the Setup Wizard.
D-Link DAP-1360 User Manual
40
Section 3 - Configuration
Choose which Security Mode you want to use and click
Next to continue.
If you choose WEP, enter the wireless security password
and click Next to complete the Setup Wizard.
D-Link DAP-1360 User Manual
41
Section 3 - Configuration
If you choose WPA, enter the WPA Personal Passphrase and
click Next to complete the Setup Wizard.
If you choose WPA2, enter the WPA2 Personal Passphrase and
click Next to complete the Setup Wizard.
The Wireless Setup Wizard is complete.
Click Finish to reboot the device.
D-Link DAP-1360 User Manual
42
Section 3 - Configuration
Add Wireless Devices With WPS
To add a windows device to your network using the Push Button Configuration Wi-Fi Protected Setup(WPS), follow
these instructions:
Select PIN to use your PIN number from your wireless
device to connect to your network.
For PBC configuration, skip to next page.
Click Connect to continue.
Start WPS on the wireless device you are adding to you
wireless network to complete the setup.
D-Link DAP-1360 User Manual
43
Section 3 - Configuration
Select PBC to use the Push Button Configuration to
connect to your network.
Click Connect to continue.
Press down the Push Button on the wireless device you
are adding to your network to complete the setup.
D-Link DAP-1360 User Manual
44
Section 3 - Configuration
Wireless Setup
Access Point
In the AP mode, the DAP-1360 acts as a central connection point for any computer (client) that has an 802.11n or backward-compatible
802.11b/g wireless network adapter and is within range of the AP.
Enable Wireless:
Select this to turn Wi-Fi on and off. Use the dropdown box to select if you want to use a schedule.
Click Add New to add or change a schedule.
Wireless Mode:
Select the wireless mode from Access Point,
Wireless Client, Repeater, Bridge, Bridge
with AP mode, WISP Client Router and WISP
Repeater.
Wireless Network
Name (also called
the SSID):
The Wireless Network Name is a unique name
that identifies a network. All devices on a network
must share the same wireless network name
in order to communicate on the network. If you
decide to change the wireless network name
from the default setting, enter your new wireless
network name in this field.
Enable Auto
Channel Scan:
Check the box to enable Auto Channel Scan.
Enable this feature to auto-select the channel
for the best wireless performance.
Wireless Channel:
Auto channel selection is the default setting. First
disable Auto Channel Scan (see below) and you
will be able to select a wireless channel.
802.11 Mode:
Select the appropriate 802.11 mode based on the wireless clients in your network. The drop-down menu options are 802.11g
Only, Mixed 802.11b/g, 802.11b Only, 802.11n Only, or Mixed 802.11b/g/n.
D-Link DAP-1360 User Manual
45
Section 3 - Configuration
Channel Width: Select the appropriate channel width between 20MHz or Auto 20/40MHz from the pull-down menu.
Transmission Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.
Rate:
Enable Hidden Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen
Wireless: by site survey utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to
connect to it.
Wireless Security Select a wireless security setting. Options are None, WEP, WPA, WPA2, or WPA2-Auto. See P.75, Wireless Security,
Mode: of this manual for a detailed explanation of the wireless security options.
Wi-Fi Protected Enable or disable the Wi-Fi protected setup feature.
Setup:
Lock Wireless Locking the wireless security prevents the settings from being changed by any new external registar using its PIN. Devices
Security: can still be added to the wireless network using Wi-Fi Protected Setup. It is still possible to change wireless network settings
with Manual Wireless Network Setup, Wireless Network Setup Wizard, or an existing external WLAN Manager Registar.
Current PIN: Shows the current value of the access point’s PIN.
Generate New PIN: Create a random number that is a valid PIN. This becomes the access point’s PIN. You can then copy this PIN to the user
interface of the registrar.
Reset PIN to Restore the default PIN of the access point.
Default:
Reset to Resets the Wi-Fi Protected Status to Not Configured. Vista WPS icon will only be displayed when the Wi-Fi Protected Status
Unconfigured: is Not Configured.
D-Link DAP-1360 User Manual
46
Section 3 - Configuration
Repeater
The Wireless Repeater mode extends the wireless coverage of another wireless AP or wireless router.
Enable Wireless:
Select this to turn the Wi-Fi module on and off. Use the drop-down box to select if you want to use a schedule. Click Add
New to add or change a schedule.
Site Survey:
Click this button to choose the root AP from an
available connection list.
Wireless Network
Name (also called
the SSID):
The Wireless Network Name is a unique name
that identifies a network. All devices on a network
must share the same wireless network name
in order to communicate on the network. If you
decide to change the wireless network name
from the default setting, enter your new wireless
network name in this field.
Wireless Channel:
The channel will follow the root AP. The channel
used will be displayed.
802.11 Mode:
Select the appropriate 802.11 mode based on
the wireless clients in your network. The dropdown menu options are 802.11g Only, Mixed
802.11b/g, 802.11b Only, 802.11n Only, or
Mixed 802.11b/g/n.
Channel Width:
Transmission Rate:
Select the appropriate channel width between 20MHz or Auto 20/40MHz from the pull-down menu.
Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.
Enable Hidden
Wireless:
Check the box if you do not want the SSID to be broadcast by the DAP-1360. This prevents the SSID from being seen
by site survey utilities, so any wireless clients will have to be pre-configured with the SSID of the DAP-1360 in order to
connect to it.
Wireless Security
Mode:
Select a wireless security setting. Options are None, WEP, WPA, or WPA2. See P.75, Wireless Security, of this manual
for a detailed explanation of the wireless security options.
Wi-Fi Protected
Setup:
Select enable if you want to configure 1360 with WPS.
D-Link DAP-1360 User Manual
47
Section 3 - Configuration
Wireless Client
In the Wireless Client mode, the DAP-1360 acts as a wireless network adapter for your Ethernet-enabled device (such as a game console
or a TV set-top box).
Enable Wireless:
Select this to turn the Wi-Fi module on and off. Use the drop-down
box to select if you want to use a schedule. Click Add New to add
or change a schedule.
Wireless Type:
Select Infrastructure if you only connect your DAP-1360 to other
wireless clients (as such wireless PCs). Select Ad-Hoc if you
connect your DAP-1360 to another DAP-1360 operating in the AdHoc mode.
Wireless Network
Name (also called
the SSID):
You can input the wireless network name of the root AP or click the
Site Survey button to find the root AP.
Site Survey:
Click this button to choose the root AP from an available connection
list.
Wireless Channel:
The channel used will be displayed.
The channel will follow the root AP.
802.11 Mode:
Select the appropriate 802.11 mode based on the wireless clients
in your network. The drop-down menu options are 802.11g
Only, Mixed 802.11b/g, 802.11b Only, 802.11n Only, or Mixed
802.11b/g/n.
Channel Width:
Select the appropriate channel width between 20MHz or Auto
20/40MHz from the pull-down menu.
Transmission Rate:
Select the transmission rate. It is strongly suggested to use the
Auto setting for optimal performance.
Wireless MAC
Clone :
If you disable this option, your DAP-1360 will fill the source MAC
address field of all packets that it forwards with its own MAC address. If you enable this option, manually type in a different
scource MAC address for the DAP-1360 to use in all packets that it forwards.
Wireless Security
Mode:
Select a wireless security setting. Options are None, WEP, WPA, or WPA2. See P.75, Wireless Security, of this manual
for a detailed explanation of the wireless security options.
Wi-Fi Protected
Setup:
Select enable if you want to configure 1360 with WPS.
D-Link DAP-1360 User Manual
48
Section 3 - Configuration
Bridge
The Bridge mode connects 2 LANs together.
Enable Wireless: Select this to turn the Wi-Fi module on and off.
Use the drop-down box to select if you want to
use a schedule. Click Add New to add or change
a schedule.
Wireless Network The Wireless Network Name is a unique name that
Name (also called identifies a network. All devices on a network must
the SSID): share the same wireless network name in order
to communicate on the network. If you decide to
change the wireless network name from the default
setting, enter your new wireless network name in
this field.
Wireless Channel: All devices on the network must share the same
channel.
802.11 Mode: Select the appropriate 802.11 mode based on
the wireless clients in your network. The dropdown menu options are 802.11g Only, Mixed
802.11b/g, 802.11b Only, 802.11n Only, or Mixed
802.11b/g/n.
Channel Width: Select the appropriate channel width between
20MHz or Auto 20/40MHz from the pull-down
menu.
Transmission Rate: Select the transmission rate. It is strongly suggested to use the Auto setting for optimal performance.
Remote AP MAC: Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.
Bridge Security: Select None to disable encryption to across the network. Select WEP 64bits or WEP 128bits to limit communication to
only those devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a
password and dynamic key changes (No RADIUS server required).
Note: The Bridge mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with other APs
(even other D-Link APs) is not guaranteed.
D-Link DAP-1360 User Manual
49
Section 3 - Configuration
Bridge with AP
The Bridge with AP mode connects 2 LANs, while still functioning as a wireless AP for local wireless clients.
Enable Wireless: Select this to turn the Wi-Fi module on and off. Use the
drop-down box to select if you want to use a schedule.
Click Add New to add or change a schedule.
Wireless Network The Wireless Network Name is a unique name that
Name (also called identifies a network. All devices on a network must
the SSID): share the same wireless network name in order to
communicate on the network. If you decide to change
the wireless network name from the default setting,
enter your new wireless network name in this field.
Wireless Channel: Input a new number if you want to change the default
setting. All devices on the network must be set to the
same channel to communicate on the network.
802.11 Mode: Select the appropriate 802.11 mode based on the
wireless clients in your network. The drop-down menu
options are 802.11g Only, Mixed 802.11b/g, 802.11b
Only, 802.11n Only, or Mixed 802.11b/g/n.
Channel Width: Select the appropriate channel width between 20MHz
or Auto 20/40MHz from the pull-down menu.
Transmission Rate: Select the transmission rate. It is strongly suggested
to use the Auto setting for optimal performance.
Enable Hidden Check the box if you do not want the SSID to be
Wireless: broadcast by the DAP-1360. This prevents the SSID
from being seen by Site Survey utilities, so any
wireless clients will have to be pre-configured with the
SSID of the DAP-1360 in order to connect to it.
Wireless Security Select a wireless security setting. Options are None, WEP, WPA, WPA2, or WPA2-Auto. See p.34 of this manual for a
Mode: detailed explanation of the wireless security options.
Remote AP MAC: Enter the MAC addresses of the APs in your network that will serve as bridges to wirelessly connect multiple networks.
Bridge Security: Select None to disable encryption to across the network. Select WEP 64bits or WEP 128bits to limit communication to
only those devices that share the same WEP settings. Select WPA-PSK or WPA2-PSK to secure your network using a
password and dynamic key changes (no RADIUS server required).
Note: The Bridge with AP mode is not completely specified in the Wi-Fi or IEEE standards. This mode can work with other DAP-1360 units. Communication with
other APs (even other D-Link APs) is not guaranteed.
D-Link DAP-1360 User Manual
50
Section 3 - Configuration
WISP Client Router and WISP Repeater
In the WISP Router Client mode, the DAP-1360 wirelessly connects to a WISP (Wireless Internet Service Provider) AP. In this mode, the
DAP-1360 also acts as a router for wired clients on your LAN and provides NAT (Network Address Translation) and a DHCP server to generate
IP addresses for wired clients. NAT and the DHCP server allow many computers to share the same wireless Internet connection.
WISP Repeater wireless mode acts the same as WISP Client Router wireless mode, with the addition of a wireless signal for any wireless
clients on the LAN.
Enable Wireless: Select this to turn the Wi-Fi module on and off. Use the
drop-down box to select if you want to use a schedule.
Click Add New to add or change a schedule.
Wireless Network You can input the wireless network name of the root
Name: AP or click the Site Survey button to find the root
AP.
Site Survey: Click this button to choose the root AP from an
available connection list. If the root AP has wireless
encryption, you have to use the same wireless
security mode to connect the root AP.
Wireless Channel: The channel used will be displayed. The channel
will follow the root AP.
802.11 Mode: Select the appropriate 802.11 mode based on the
wireless clients in your network. The drop-down menu
options are 802.11g Only, Mixed 802.11b/g, 802.11b
Only, 802.11n Only, or Mixed 802.11b/g/n.
Channel Width: Select the appropriate channel width between 20MHz
or Auto 20/40MHz from the pull-down menu.
Transmission Rate: Select the transmission rate. It is strongly suggested
to use the Auto setting for optimal performance.
Enable Hidden This option is unavailable in WISP Client Router
Wireless: and available in the WISP Repeater mode.
Wireless Security Select a wireless security setting. Options are None,
Mode: WEP, WPA, or WPA2. See P.75, Wireless Security, of this manual for a detailed explanation of the wireless security
options.
D-Link DAP-1360 User Manual
51
Section 3 - Configuration
WAN Settings
Dynamic IP (DHCP)
WAN settings are only used in the WISP Client Router wireless mode and the WISP Repeater wireless mode. Choose Dynamic
IP(DHCP) to obtain IP Address information automatically from your ISP. Select this option if your ISP does not give you any IP number
to use. This option is commonly used for Cable modem services.
Host Name:
The Host Name is optional but may be
required by some ISPs.
MTU Size:
You may need to change the MTU
(Maximum Transmission Unit) for optimal
performance with your specific ISP. The
default MTU size is 1500.
Attain DNS
automatically:
Select this option if you want the DAP-1360
to get the DNS (Domain Name System)
server IP address automatically.
Set DNS manually: Select this option if you want to manually
enter the DNS Server IP address(es). The
fields to enter the Primary and Secondary
DNS server IP addresses will appear after
you have selected this option.
Primary/ Secondary
DNS Server:
Enter the Primary and Secondary DNS server IP address assigned by your ISP.
Clone MAC address:
The default MAC address is set to the Ethernet MAC address your DAP-1360. You can click the Clone Your PC's
MAC Address button to replace the AP's MAC address with the MAC address of the PC that you used to register with
your ISP. It is not recommended that you change the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
52
Section 3 - Configuration
Static IP
Select Static IP if all WAN IP information is provided to you by your ISP. You will need to enter in the IP address, subnet mask, gateway
address, and DNS address(es) provided to you by your ISP.
IP Address:
192.168.1.1 is the default WAN IP Address
of the DAP-1360.
Subnet Mask:
255.255.255.0 is the default subnet mask.
All devices on the network must have the
same subnet mask to communicate on the
network.
Default Gateway:
Enter the IP Address of the gateway
in your network. The default setting is
192.168.1.254.
MTU Size:
You may need to change the MTU
(Maximum Transmission Unit) for optimal
performance with your specific ISP. The
default MTU size is 1500.
Primary/ Secondary
DNS Server:
Secondary DNS
Server:
Clone MAC address:
Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.
This is optional.
The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your
PC's MAC Address button to replace the AP's MAC address with the MAC address of your Ethernet card. It is not
recommended that you change the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
53
Section 3 - Configuration
PPPoE
Choose PPPoE (Point-to-Point Protocol over Ethernet) if your ISP uses a PPPoE connection. Your ISP will provide you with a username
and password. This option is typically used for DSL services. Make sure to remove your PPPoE software from your computer. The
software is no longer needed and will not work through the DAP-1360.
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password and then
retype the password in the next box.
Service Name: Enter the ISP Service Name (optional).
Reconnection Type: Select Always on, On demand, or Manual.
Maximum Idle time: Enter a maximum idle time during which the
Internet connection is maintained during
inactivity.
MTU Size: Y o u m a y n e e d t o c h a n g e t h e M T U
(Maximum Transmission Unit) for optimal
performance with your specific ISP. The
default MTU size is 1492.
Attain DNS Select this option if you want the DAP-1360
Automatically: to get the DNS (Domain Name System)
server IP address automatically.
Set DNS Manually: Select this option if you want to manually enter the DNS Server IP address(es). Fields to enter the Primary
and Secondary DNS server IP addresses will appear after you select this option.
Primary/ Secondary Enter the Primary and Secondary DNS server IP address assigned by your ISP.
DNS Server:
Clone MAC Address: The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your
PC's MAC Address button to replace the AP's MAC address with the MAC address of your Ethernet card. It is not
recommended that you change the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
54
Section 3 - Configuration
PPTP
Choose PPTP (Point-to-Point Tunneling Protocol) if your ISP uses a PPTP connection. Your ISP will provide you with a username and
password. This option is typically used for DSL services.
PPTP IP Address: Enter the IP address (Static PPTP only).
PPTP Subnet Mask: Enter the subnet mask.
PPTP Server IP Enter the Server IP Address provided by
Address: your ISP.
Username: Enter your PPTP account name.
Password: Enter your PPTP password and then
retype the password in the next box.
MTU Size: Y o u m a y n e e d t o c h a n g e t h e M T U
(Maximum Transmission Unit) for optimal
performance with your specific ISP. The
default MTU size is 1400.
Attain DNS Select this option if you want the DAP-1360
automatically: get DNS server IP address automatically.
Set DNS Manually: Select this option if you want to manually
enter the DNS Server IP address(es).
Fields to enter the Primary and Secondary
DNS server IP addresses will appear after
you select this option.
Primary/ Secondary Enter the Primary and Secondary DNS (Domain Name System) server IP address assigned by your ISP.
DNS Server:
Clone MAC address: The default MAC address is set to the MAC address on the AP (Access Point). You can click the Clone Your
PC's MAC Address button to replace the AP's MAC address with the MAC address of your Ethernet card. It is not
recommended that you change the default MAC address unless required by your ISP.
D-Link DAP-1360 User Manual
55
Section 3 - Configuration
LAN Setup
The LAN (Local Area Network) is your private, internal network. This page allows you to configure the IP settings of the
LAN interface for the DAP-1360. The IP address can be changed to your current network IP range. This IP address
cannot be seen from the Internet.
D-Link DAP-1360 User Manual
56
Section 3 - Configuration
LAN Settings
My LAN
Connection is:
The DAP-1360 is set to Static IP by default.
Select this option if you do not have a DHCP
server on your network, or if you wish to assign
a static IP address to the DAP-1360.
Static IP:
Select this option if you are manually assigning
an IP Address.
Dynamic IP:
Select this option if you would like to have an
IP Address automatically assigned to the DAP1360 by a DHCP server in your network.
IP Address:
Enter the IP address of the access point.
Subnet Mask:
Enter the subnet mask of your access point.
Gateway address: Enter the IP Address of the router in your network.
Device This allows you to configure this device more
Name(NetBIOS easily when your network using TCP/IP protocol.
Name): You can enter the device name of the AP into
your web browser to access the instead of ip
address for configuration.If you are using the device name to connect, ensure that your PC and your DAP-1360 are on
the same network.
Enable DHCP Select this to enable the DHCP server if static IP address is selected.
Server:
DHCP IP Address Enter the starting and ending IP addresses for the DHCP server’s IP assignment.
Range Lease Time: Enter the length of time for the IP address lease.
D-Link DAP-1360 User Manual
57
Section 3 - Configuration
Advanced
Advanced Wireless
Transmit Power:
Choose 100%, 50%(-3dB), 25% (-6dB), or
12.5% (-9dB).
Beacon Period: Beacons are packets sent by an access point
to synchronize a wireless network. Specify a
beacon interval value. The default value 100
is recommended.
RTS Threshold: This value should remain at its default setting of
2,432. If you encounter inconsistent data flow,
only minor modifications to the value range
between 256 and 2,432 are recommended.
Fragmentation This value should remain at its default setting of 2,346. If you experience a high packet error rate, you may slightly
Threshold: decrease your fragmentation threshold within the value range of 256 to 2,346. Setting the fragmentation threshold too
low may result in poor performance.
DTIM Interval
(Beacon Rate):
A DTIM (Delivery Traffic Indication Message) is a countdown informing clients of the next window for listening to broadcast
and multicast messages. The default vaule is 3 and the possible range of vaules is between 1 and 255.
Preamble Type:
Select Short or Long Preamble. The default setting in Long Preamble. The Preamble defines the length of the CRC block
(Cyclic Redundancy Check is a common technique for detecting data transmission errors) for communication between
the access point and roaming wireless network adapters. Note: High network traffic areas should use the short preamble
type.
WMM:
WMM (Wi-Fi Multimedia) is only available in the Access Point and Wireless Client Mode. WMM provides basic QoS (Quality
of Service) functions for wireless networks. WMM prioritizes traffic based on 4 AC (Access Categories) : voice, video, best
effort, and background. However, WMM does not provide guaranteed throughput.The QoS (WMM) is mandatory in 11n
mode, you can disable this feature when select 11g or 11b mode.
Enable Multicast
Streams:
Use this function to enable IGMP Snooping for your wireless connection. This function will enhance your network performance
when you use multicast services such as video conferencing and video/audio streaming. This setting is enabled by default
and cannot be changed in the DAP-1360’s current fimware version.
D-Link DAP-1360 User Manual
58
Section 3 - Configuration
Access Control
Use MAC Filters to allow or deny wireless clients, by their MAC addresses, from accessing the DAP-1360. You can manually add a MAC
address or select the MAC address from the list of clients that are currently connected to the AP (Connected PCs). The default setting is
Disable MAC Filters.
Access Control: Access control is set to Disable by default.
Select Reject to deny access to the AP. Select
Accept to allow access to the AP.
MAC Address: Enter the MAC address of the client that you
want to allow or deny access to the AP.
Connected PCs: Select the MAC address of a computer from
the drop-down menu and click Clone to fill in
the MAC Address field with that computer.
MAC Filter List: This list will display the MAC addresses that
are in the selected filter.
D-Link DAP-1360 User Manual
59
Section 3 - Configuration
User Limit
The D-Link DAP-1360 can set a limit upon the number of wireless clients. Using user limit, you can prevent scenarios
where the DAP-1360 in your network shows performance degradation because it is handling heavy wireless traffic.
Enable User Limit: Click this to enable the User Limit options on
this page.
User Limit (1 - 32): Type the maximum number of wireless
connections that can be made to the AP.
D-Link DAP-1360 User Manual
60
Section 3 - Configuration
Port Forwarding
This function is available if your DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to open a single
port or a range of ports. Click Save Settings and the port forwarding rule will be put into the Port Forwarding List.
Port Forwarding Check the box to configure a port forwarding
Rules: rule.
Name: Enter a name for the rule. You can select an
application name from the Application Name
drop-down menu. Click the << button to fill in
the Name field with the application name that
you selected.
IP Address: Enter the IP address of the computer on
your local network that you want to allow the
incoming service to.
Start Port/End Enter the port or ports that you want to open.
Port: If you want to open one port, enter the same
port in both boxes.
Traffic Type: Select TCP, UDP, or Both.
D-Link DAP-1360 User Manual
61
Section 3 - Configuration
Port Filter
This function is available if the DAP-1360 is in WISP Client Router or WISP Repeater mode. This feature is used to secure or restrict your
local network. It will deny the ports that you enter from the local network to the Internet. Click Save Settings and the port filter rule will
be put into the Port Filter List.
Port Filter Rules: Check the box to configure a port filter rule.
Name: Enter a name for the rule. You can select an
application name from the Application Name
drop-down menu. Click the << button to fill in
the Name field with the application name that
you selected.
Start Port/End Enter the port or ports that you want to open.
Port: If you want to open one port, enter the same
port in both boxes.
Traffic Type: Select TCP, UDP, or Both.
D-Link DAP-1360 User Manual
62
Section 3 - Configuration
DMZ
This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to set up
a DMZ (Demilitarized Zone) host. If you have a client PC that cannot run Internet applications properly from behind the DAP-1360, then
you can set the client up for unrestricted Internet access. The DMZ allows a computer to be exposed to the Internet. This feature is useful
for gaming purposes. Enter the IP address of the computer that will be the DMZ host. Adding a client to the DMZ may expose your local
network to a variety of security risks, so only use this option as a last resort.
Enable DMZ: Check this box to enable DMZ.
DMZ Host IP Enter the IP address of the computer you
Address: would like to open all ports to. You can select
a computer from the Computer Name dropdown menu and click << to enter the computer
name into the DMZ Host IP Address field.
D-Link DAP-1360 User Manual
63
Section 3 - Configuration
Parental Control
This function is available only if the DAP-1360 is in the WISP Client Router or WISP Repeater mode. This feature allows you to create a
list of websites that you want to deny users access.
Configure Website Select Turn Website Filtering OFF or Turn
Filtering below: Website Filtering ON and DENY computers
access to ONLY these sites.
Website URL Enter a keyword or URL that you want to
Address: block and click Save Settings. Any URL that
contains the keyword will be blocked.
D-Link DAP-1360 User Manual
64
Section 3 - Configuration
Advanced Network
This function is available if the DAP-1360 is in WISP Client Router or WISP Repeater mode. This feature allows you to change the LAN
settings. Please be aware that any changes to the factory default settings may affect the behavior of your network.
Enable UPnP: Check this box to use the Universal Plug
and Play (UPnP™) feature. UPnP provides
compatibility with networking equipment,
software and peripherals.
Enable WAN Check this box to allow the WAN port of the
Ping Respond: DAP-1360 to be pinged. Unchecking the box
will not allow the DAP-1360 to respond to
pings. Blocking ping response may provide
some extra security from intruders.
Remote Remote management allows the DAP-1360
Management: to be configured from the Internet by a web
browser. A username and password are still
required to access the Web-Management
interface. In general, only a member of your
network can browse the built-in web pages
to perform Administrator tasks. This feature
enables you to perform Administrator tasks
from the remote (Internet) host.
D-Link DAP-1360 User Manual
65
Section 3 - Configuration
Maintenance
Device Administration
New Enter a new password.
Password:
Confirm Re-enter the password to confirm it.
Password:
Save and Restore
Save Settings To
Local Hard Drive:
Click Save to save the current system
settings as a file onto your local hard
drive.
Load Settings From
Local Hard Drive:
To load a system settings file, click on
Browse to browse the local hard drive
and locate the system settings file to be
used. Click Upload Settings when you
have selected the file to be loaded back
onto the access point.
Restore To Factory You can reset the DAP-1360 back to the
Default Settings: factory default settings by clicking on
Restore Device. Make sure to save the
current system settings before clicking on
Restore Device. You will lose your current
system settings after you click Restore
Device.
D-Link DAP-1360 User Manual
66
Section 3 - Configuration
Firmware
This feature is used to update the firmware of the DAP-1360. The current firmware version and firmware date are displayed here. Please
check the D-Link support site for firmware or language package updates at http://support.dlink.com.tw.
Click here to check
for an update on our
support site:
Click this link and you will be connected to
D-Link’s support website where you can
download the latest firmware version to
your local hard drive.
Current Firmware
Info:
To update the firmware, click on Browse
to browse the local hard drive and locate
the updated firmware file. Click the
Upload button after you have selected
the updated firmware file.
Language Package
Information:
To change the web configurator language,
click on Browse to browse locate the
language package upgrade file and click
the Upload button.
D-Link DAP-1360 User Manual
67
Section 3 - Configuration
Watchdog (Ping of Life)
The Watchdog feature pings a specified IP address. If the IP address stops responding to pings, your AP will be rebooted. You can also
select an option to have the DAP-1360 send an e-mail alert if the specified IP address stops responding to pings.
Enable Watchdog
(Ping of Life):
Check this box to enable the Watchdog
(Ping of Life) to check some host IP.
Update Time
Interval:
Enter the time interval of how often you
would like the Watchdog to ping the
response IP address.
Watchdog Response
IP:
Enter the IP address that the Watchdog
will ping.
Enable Mail Alert:
Check this box to enable e-mail notification
for the Watchdog.
SMTP Server:
Enter the SMTP server IP address.
Sender E-Mail: Enter the e-mail address from which the
notification will be sent.
Receiver E-Mail:
Enter the e-mail address which the
notification will be sent to.
Enable
Authentication:
Check the box to enable authentication
that is used with the SMTP server.
Account Name:
Enter your account name that is used with
the SMTP server.
Password:
Enter your password that is used with
the SMTP server and re-enter it in the
next box.
D-Link DAP-1360 User Manual
68
Section 3 - Configuration
Time
The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system
clock. From this section you can set the time zone that you are in and set the Time Server. Daylight Saving can also
be configured to automatically adjust the time when needed.
Time Zone: Select the Time Zone from the drop-down menu.
Daylight Saving: To select Daylight Saving time manually, select
enabled or disabled, and enter a start date and an
end date for daylight saving time.
Enable NTP Server: NTP is short for Network Time Protocol. NTP
synchronizes computer clock times in a network
of computers. Check this box to use a NTP server.
This will only connect to a server on the Internet,
not a local server.
NTP Server Used: Enter the NTP server or select one from the
drop-down menu.
Manual: To manually input the time, enter the values in these
fields for the Year, Month, Day, Hour, Minute, and
Second and then click Save Settings. You can also
click Copy Your Computer’s Time Settings.
D-Link DAP-1360 User Manual
69
Section 3 - Configuration
Schedules
Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from
3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and
End Time of 8pm.
Name: Enter a name for your new schedule.
Days: Select a day, a range of days, or All Week to
include every day.
Time: Check All Day - 24hrs or enter a start and end
time for your schedule.
Save: Click Save to save your schedule. You must click
Save Settings at the top for your schedules to
go into effect.
Schedule Rules The list of schedules will be listed here. Click the
List: Edit icon to make changes or click the Delete
icon to remove the schedule.
D-Link DAP-1360 User Manual
70
Section 3 - Configuration
Status
Device Info
This screen displays the current firmware version and the current LAN, and Wireless LAN settings on your access
point.
D-Link DAP-1360 User Manual
71
Section 3 - Configuration
Log
The DAP-1360 keeps a running log of events and activities occurring on the AP. If the AP is rebooted, the logs are
automatically cleared. You can save the log files under Log Setting.
First Page: This button directs you to the first page of
the log.
Last Page: This button directs you to the last page of
the log.
Previous Page: This button directs you to the previous
page of the log.
Next Page: This button directs you to the next page
of the log.
Clear Log: This button clears all current log content.
Log Settings: This button opens a new menu where you
can configure the log settings.
Refresh: This button refreshes the log.
D-Link DAP-1360 User Manual
72
Section 3 - Configuration
Statistics
The DAP-1360 keeps statistics of the traffic that passes through it. You can view the amount of packets that pass
through the LAN and wireless portions of the network. The traffic counter will reset if the access point is rebooted.
Wireless
This list displays the MAC addresses of connected wireless clients and the length of time that they have been
connected.
D-Link DAP-1360 User Manual
73
Section 3 - Configuration
Help
The Help menu contains an index of links to help topics for each feature of the DAP-1360.
D-Link DAP-1360 User Manual
74
Section 4 - Security
Wireless Security
This section will show you the different levels of security you can use to protect your data from intruders. The
DAP-1360 offers the following types of security:
• WPA-Personal (Pre-Shared Key)
• WPA2-Personal (Pre-Shared Key 2)
• WPA2-Auto-Personal
• WEP (Wired Equivalent Privacy)
• WPA-Enterprise (Extensible Authentication Protocol)
• WPA2-Enterprise (Extensible Authentication Protocol 2)
• WPA2-Auto-Enterprise (Extensible Authentication Protocol 2 Auto)
What is WEP?
WEP stands for Wired Equivalent Privacy. It is based on the IEEE 802.11 standard and uses the RC4 encryption
algorithm. WEP provides security by encrypting data over your wireless network so that it is protected as it is transmitted
from one wireless device to another.
To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When
using WEP, you must determine the level of encryption. The type of encryption determines the key length. 128-bit
encryption requires a longer key than 64-bit encryption. Keys are defined by entering in a string in HEX (hexadecimal
- using characters 0-9, A-F) or ASCII (American Standard Code for Information Interchange – alphanumeric characters)
format. ASCII format is provided so you can enter a string that is easier to remember. The ASCII string is converted to
HEX for use over the network. Four keys can be defined so that you can change keys easily.
D-Link DAP-1360 User Manual
75
Section 4 - Security
Configure WEP
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1.Log into the web-based configuration utility by
opening a web browser and entering the device
name of the access point (dlinkap). Click on
Wireless Setup on the left side.
2. Next to Security Mode, select Enable WEP Wireless
Security (Basic).
3. Next to Authentication, select Shared Key or
Open.
4. Next to WEP Encryption, select 64-bit or 128-bit
encryption.
5. Next to Key Type, select either Hex or ASCII.Hex
(recommended) - Letters A-F and numbers 0-9 are
valid. ASCII - All numbers and letters are valid.
6. Next to Key 1, enter a WEP key that you create.
Make sure you enter this key exactly on all your
wireless devices. You may enter up to 4 different
keys.
7. Click Save Settings to save your settings. If you are configuring the access point with a wireless adapter, you will lose
connectivity until you enable WEP on your adapter and enter the same WEP key as you did on the access point.
D-Link DAP-1360 User Manual
76
Section 4 - Security
What is WPA?
WPA, or Wi-Fi Protected Access, is a Wi-Fi standard that was designed to improve the security features of WEP (Wired
Equivalent Privacy).
There are 2 major improvements over WEP:
• Improved data encryption through the Temporal Key Integrity Protocol (TKIP). TKIP scrambles the keys
using a hashing algorithm and by adding an integrity-checking feature ensures that the keys haven’t
been tampered with.
• User authentication, which is generally missing in WEP, is done through the Extensible Authentication
Protocol (EAP). WEP regulates access to a wireless network based on a computer’s hardware-specific
MAC address, which is relatively simple to be sniffed out and stolen. EAP is built on a more secure publickey encryption system to ensure that only authorized network users can access the network.
WPA-PSK/WPA2-PSK uses a passphrase or key to authenticate your wireless connection. The key is an alpha-numeric
password between 8 and 63 characters long. The password can include symbols (!?*&_) and spaces. This key must
be the exact same key entered on your wireless router or access point.
WPA-EAP/WPA2-EAP incorporates user authentication through the Extensible Authentication Protocol (EAP). EAP
is built on a more secure public key encryption system to ensure that only authorized network users can access the
network.
WPA2-Auto-PSK/WPA2-Auto-EAP accepts wireless clients that use WPA or WPA2. Authentication is sill necessary.
D-Link DAP-1360 User Manual
77
Section 4 - Security
Configure WPA-PSK, WPA2-PSK, and
WPA2-Auto-PSK (Personal)
It is recommended to enable encryption on your wireless access point before your wireless
network adapters. Please establish wireless connectivity before enabling encryption. Your
wireless signal may degrade when enabling encryption due to the added overhead.
1.Log into the web-based configuration utility
by opening a web browser and entering the
device name of the access point (dlinkap).
Click on Wireless Setup on the left side.
2. Next to Security Mode, select Enable
WPA Wireless Security, Enable
WPA2 Wireless Security, or Enable
WPA2-Auto Wireless Security.
3. Next to Cipher Mode, select
TKIP, AES, or Auto.
4. Next to PSK / EAP, select Personal.
5.Next to Passphrase, enter a key (passphrase). The key is an alpha-numeric password between 8 and 63
characters long. The password can include symbols (!?*&_) and spaces. Make sure you enter this key
exactly the same on all other wireless clients. Enter the passphrase again next to Confirmed Passphrase.
7.Click Save Settings to save your settings. If you are configuring the access point with a wireless
adapter, you will lose connectivity until you enable WPA-Personal, WPA2-Personal, or WPA2-AutoPersonal on your adapter and enter the same passphrase as you did on the access point.
D-Link DAP-1360 User Manual
78
Section 4 - Security
Configure WPA-EAP, WPA2-EAP, and
WPA2-Auto-EAP (Enterprise)
It is recommended to enable encryption on your wireless access point before your wireless network adapters. Please
establish wireless connectivity before enabling encryption. Your wireless signal may degrade when enabling encryption
due to the added overhead.
1.Log into the web-based configuration utility by opening a web browser and entering the device name of the access
point (dlinkap). Click on Wireless Setup on the
left side.
2. Next to Security Mode, select Enable WPA
Wireless Security, Enable
WPA2 Wireless Security, or Enable
WPA2-Auto Wireless Security.
3. Next to Cipher Mode, select
TKIP, AES, or Auto.
4. Next to Personal / Enterprise,
select Enterprise.
5.Next to RADIUS Server enter the IP Address of
your RADIUS server.
6.Next to Port, enter the port you are using with your RADIUS server. 1812 is the default port.
7.Next to Shared Secret, enter the security key.
8.Click Save Settings to save your settings.
D-Link DAP-1360 User Manual
79
Section 5 - Connecting to a Wireless Network
Connect to a Wireless Network
Using Windows® XP
Windows® XP users can use the built-in wireless utility (Zero Configuration Utility) to connect to a wireless network.
The following instructions are for Service Pack 2 users. If you are using another company’s utility or Windows® 2000,
please refer to the user manual of your wireless adapter for help with connecting to a wireless network. Most utilities
will have a “site survey” option similar to the Windows® XP utility as shown below.
If you receive the Wireless Networks Detected bubble, click
on the center of the bubble to access the utility.
or
Right-click on the wireless computer icon in your system tray
(lower-right corner next to the time). Select View Available
Wireless Networks.
The utility will display all available wireless networks in your
area. Click on a network (displayed using the SSID) and click
the Connect button.
If you get a good signal but cannot access the Internet,
check the TCP/IP settings for your wireless adapter. Refer
to the Networking Basics section in this manual for more
information.
D-Link DAP-1360 User Manual
80
Section 5 - Connecting to a Wireless Network
Configure WEP/WPA-PSK
It is recommended to enable WEP or WPA-PSK on your wireless access point before configuring your wireless adapter.
If you are joining an existing network, you will need to know the WEP or WPA-PSK key being used.
Follow the steps on the previous page to connect to a wireless network
using Windows® XP. After you highlight a network and click Connect,
the Wireless Network Connection box will appear if the network
requires authentication. Enter the same WEP or WPA-PSK key that
is on your access point and click Connect.
It may take 20-30 seconds to connect to the wireless network. If the
connection fails, please verify that the WEP or WPA-PSK settings are
correct. The WEP or WPA-PSK key must be exactly the same as on
the wireless access point.
D-Link DAP-1360 User Manual
81
Section 5 - Connecting to a Wireless Network
Using Windows® Vista (Secured Network)
The following are step-by-step directions to connect to a secured wireless network using Windows® Vista.
1. Right-click on Network and click on Properties.
2.Click the Manage network connections link in the Network
and Sharing Center window.
D-Link DAP-1360 User Manual
82
Section 5 - Connecting to a Wireless Network
3.Right-click the Wireless Network Connection entry and then select
Connect/Disconnect from the drop-down menu.
4.Select a network to connect to in the Select a network to connect
to window and then click the Connect button.
5.The following window displays connection progress.
D-Link DAP-1360 User Manual
83
Section 5 - Connecting to a Wireless Network
6.Enter the network security key or passphrase for the AP in the textbox
provided in the Type the network security key or passphrase for
[SSID name] window. When you are finished, click the Connect
button.
7.The following Successfully connected to [SSID name] window
is displayed. Choose to save this network and/or start this new
connection automatically. When you are finished, click the Close
button.
D-Link DAP-1360 User Manual
84
Section 5 - Connecting to a Wireless Network
Using Windows® Vista (Unsecured Network)
The following are step-by-step directions to set up a wireless connection on an unsecured network using Windows®
Vista.
1. Right-click on Network and click on Properties.
2.Go to the Network and Sharing Center window and click
the Manage Network Connections link.
D-Link DAP-1360 User Manual
85
Section 5 - Connecting to a Wireless Network
3.Right-click the Wireless Network Connection entry and then select
Connect/Disconnect from the drop-down menu.
4.Select a network to connect to in the Select a network to connect
to window and then click the Connect button.
5.Confirm that you still want to connect on the following Network
Connection Status window by clicking on Connect Anyway.
D-Link DAP-1360 User Manual
86
Section 5 - Connecting to a Wireless Network
6.The following Connect to a network wizard window displays the
connection progress.
7.The following Successfully connected to [SSID name] window
is displayed. Choose to save this network and/or start this new
connection automatically. When you are finished, click the Close
button.
D-Link DAP-1360 User Manual
87
Section 6 - Troubleshooting
Troubleshooting
This chapter provides solutions to problems that can occur during the installation and operation of the DAP-1360. Read
the following descriptions if you are having problems. The examples below use Windows® XP. If you have a different
operating system, the troubleshooting steps may be different from the following examples.
1. Why can’t I access the web-based configuration utility?
When entering the IP address of the D-Link access point (for example, dlinkap), you are not connecting to a website
on the Internet or have to be connected to the Internet. The device has the utility built-in to a ROM chip in the device
itself. Your computer must be on the same IP subnet to connect to the web-based utility.
• Make sure you have an updated Java-enabled web browser. We recommend the following:
• Internet Explorer 6.0 or higher
• Firefox 1.5 or higher
• Verify physical connectivity by checking for solid link lights on the device. If you do not get a solid link light, try using
a different cable or connect to a different port on the device if possible. If the computer is turned off, the link light may
not be on.
• Disable any internet security software running on the computer. Software firewalls such as Zone Alarm, Black Ice,
Sygate, Norton Personal Firewall, and Windows® XP firewall may block access to the configuration pages. Check the
help files included with your firewall software for more information on disabling or configuring it.
D-Link DAP-1360 User Manual
88
Section 6 - Troubleshooting
• Configure your Internet settings:
• Go to Start > Settings > Control Panel. Double-click the Internet Options Icon. From the Security tab,
click the button to restore the settings to their defaults.
• Click the Connection tab and set the dial-up option to Never Dial a Connection. Click the LAN Settings
button. Make sure nothing is checked. Click OK.
• Go to the Advanced tab and click the button to restore these settings to their defaults. Click OK three
times.
• Close your web browser (if open) and open it.
• Access the web-based configuration utility. Open your web browser and enter the IP address of your D-Link access
point in the address bar. This should open the login page for your the web-based configuration utility.
• If you still cannot access the web-based configuration utility, unplug the power to the access point for 10 seconds
and plug back in. Wait about 30 seconds and try accessing the web-based configuration utility. If you have multiple
computers, try connecting using a different computer.
2. What can I do if I forgot my password?
If you forgot your password, you must reset your access point. Unfortunately this process will change all your settings
back to the factory defaults.
To reset the access point, locate the reset button (hole) on the rear panel of the unit. With the access point powered
on, use a paperclip to hold the button down for 10 seconds. Release the button and the access point will go through
its reboot process. Wait about 30 seconds to access the access point. The default IP address is dlinkap. When logging
in, the username is admin and leave the password box empty.
D-Link DAP-1360 User Manual
89
Appendix B - Wireless Basics
Wireless Basics
D-Link wireless products are based on the latest industry standards to provide easy-to-use and compatible high-speed
wireless connectivity within your home, business, or public wireless networks. Strictly adhering to IEEE standards, the
D-Link wireless family of products allows you to securely access the data you want, when and where you want it. You
will be able to enjoy the freedom that wireless networking delivers.
A wireless local area network (WLAN) is a cellular computer network that transmits and receives data with radio signals
instead of wires. Wireless LANs are used increasingly in both home and office environments, and public areas such
as airports, coffee shops, and universities. Innovative ways to utilize WLAN technology are helping people to work
and communicate more efficiently. Increased mobility and the absence of cabling and other fixed infrastructure have
proven to be beneficial for many users.
Wireless users can use the same applications they use on a wired network. Wireless adapter cards used on laptop
and desktop systems support the same protocols as Ethernet adapter cards.
Under many circumstances, it may be desirable for mobile network devices to link to a conventional Ethernet LAN in
order to use servers, printers or an Internet connection supplied through the wired LAN. A Wireless Router is a device
used to provide this link.
D-Link DAP-1360 User Manual
90
Appendix B - Wireless Basics
What is Wireless?
Wireless or Wi-Fi technology is another way of connecting your computer to the network without using wires. Wi-Fi
uses radio waves to connect wirelessly, so you have the freedom to connect computers anywhere in your home or
office network.
Why D-Link Wireless?
D-Link is a worldwide leader and an award winning designer, developer, and manufacturer of networking products.
D-Link delivers the performance you need at a price you can afford. D-Link has all the products you need to build your
network.
How does wireless work?
Wireless works similar to how a cordless phone works- using radio signals to transmit data from one point to another.
However, wireless technology has restrictions as to how you can access the network. You must be within the wireless
network range area to be able to connect your computer. There are two different types of wireless networks: a Wireless
Local Area Network (WLAN) and a Wireless Personal Area Network (WPAN).
Wireless Local Area Network (WLAN)
In a WLAN, a device called an Access Point (AP) connects computers to the network. The access point has a small
antenna attached to it, which allows it to transmit data back and forth over radio signals. With an indoor AP, the
signal can travel up to 300 feet. With an outdoor AP the signal can reach out up to 30 miles to serve places like
manufacturing plants, industrial locations, college and high school campuses, airports, golf courses, and many other
outdoor venues.
D-Link DAP-1360 User Manual
91
Appendix B - Wireless Basics
Wireless Personal Area Network (WPAN)
Bluetooth is the industry standard wireless technology used for WPANs. Bluetooth devices in WPANs operate in a
range up to 30 feet away.
The speed and wireless operation range of a WPAN is less than of a WLAN, but it excels in its efficient consumption
of power. WPANs are ideal for personal devices, such as mobile phones, PDAs, headphones, laptops, speakers, and
other devices that operate on batteries.
Who uses wireless?
Wireless technology has become so popular in recent years that almost everyone is using it, at home and in the
office.
Home
• Gives everyone at home broadband access
• Surf the web, check email, get instant messages, etc.
• Gets rid of the cables around the house
• Simple and easy to use
Small Office and Home Office (SOHO)
• Stay on top of everything at home as you would at the office
• Remotely access your office network from home
• Share an Internet connection and printer with multiple computers
• No need to dedicate office space
D-Link DAP-1360 User Manual
92
Appendix B - Wireless Basics
Where is wireless used?
Wireless technology is quickly expanding beyond home and office use. The freedom of mobility it offers is becoming
so popular that more and more public facilities are now providing wireless access to attract people. Public places that
offer wireless access is usually called a “hotspot”.
Using a D-Link Cardbus Adapter with your laptop, you can access the hotspot to connect to Internet from remote
locations like airports, hotels, coffee shops, libraries, restaurants, and convention centers.
A wireless network is relatively easy to setup, but if you’re installing it for the first time it could be quite a task not
knowing where to start. That’s why we’ve put together a few setup steps and tips to help you through the process of
setting up a wireless network.
Tips
Here are a few things to keep in mind, when you install a wireless network.
Centralize your Access Point
Make sure you place the router/access point in a central location within your network for the best performance. Try to
place the router/access point as high as possible in the room, so the signal gets dispersed throughout your home. If
you have a two-story home, you may need a repeater to boost the signal and extend the range.
Eliminate Interference
Place home appliances such as cordless telephones, microwaves, and televisions as far away as possible from the
router/access point. This will significantly reduce any interference that the appliances might cause if operating on the
same frequency.
D-Link DAP-1360 User Manual
93
Appendix B - Wireless Basics
Security
Don’t let your next-door neighbors or unwanted intruders connect to your wireless network. Secure your wireless
network by turning on the WEP or WPA security feature on the access point. Refer to the section “Wireless Security”
in this manual for detailed information on how to set it up.
Wireless Modes
There are basically two modes of networking:
•Infrastructure – All wireless clients will connect to an access point or wireless router.
•Ad-Hoc – Directly connecting to another computer, for peer-to-peer communication, using wireless
network adapters on each computer.
An Infrastructure network contains an AP or a wireless router. All the wireless devices, or clients, will connect to the
wireless router or the AP.
An Ad-Hoc network contains only clients, such as laptops with wireless cardbus adapters. All the adapters must be in
Ad-Hoc mode to communicate.
D-Link DAP-1360 User Manual
94
Appendix C - Networking Basics
Networking Basics
Check your IP address
After you install your network adapter, by default, the TCP/IP settings should be set to obtain an IP address from a
DHCP server (i.e. wireless router) automatically. To verify your IP address, please follow the steps below.
Click on Start > Run. In the run box type cmd and click OK.
At the prompt, type ipconfig and press Enter.
This will display the IP address, subnet mask, and
the default gateway of your adapter.
If the address is 0.0.0.0, check your adapter
installation, security settings, and the settings
on your router. Some firewall software programs
may block a DHCP request on newly installed
adapters.
If you are connecting to a wireless network at a
hotspot in a hotel, coffee shop, airport, or another public place, please contact an employee or administrator to verify
their wireless network settings.
D-Link DAP-1360 User Manual
95
Appendix C - Networking Basics
Statically Assign an IP address
If you are not using a DHCP capable gateway/router, or you need to assign a static IP address, please follow the steps
below:
Step 1
Windows® XP - Click on Start > Control Panel > Network Connections.
Windows® 2000 - From the desktop, right-click My Network Places > Properties.
Step 2
Right-click on the Local Area Connection which represents your network adapter and select Properties.
Step 3
Highlight Internet Protocol (TCP/IP) and click Properties.
Step 4
Click Use the following IP address and enter an IP address that is on the same subnet as your network or the LAN
IP address on your router.
Example: If the router´s LAN IP address is 192.168.0.1, make your IP address
192.168.0.X where X is a number between 2 and 99. Make sure that the number
you choose is not in use on the network. Set Default Gateway the same as the LAN
IP address of your router (192.168.0.1).
Set Primary DNS the same as the LAN IP address of your router (192.168.0.1). The
Secondary DNS is not needed or you may enter a DNS server from your ISP.
Step 5
Click OK twice to save your settings.
D-Link DAP-1360 User Manual
96
Appendix D - Technical Specifications
Technical Specifications
NETWORK STANDARDS
- 802.11n wireless LAN
- 802.11g wireless LAN
- 802.11b wireless LAN
- 802.3/802.3u 10BASE-T/100BASE-TX Ethernet
- ANSI/IEEE 802.3 NWay auto-negotiation
DEVICE INTERFACES
- 802.11n wireless LAN
- One 10/100BASE-TX Ethernet LAN port
OPERATING FREQUENCY
2.4 to 2.4835 GHz
OPERATING CHANNELS
- FCC: 11
- ETSI: 13
ANTENNA
Two 2dBi Gain detachable omni-directional antennas with RP-SMA
connector
SECURITY
- 64/128-bit WEP data encryption
- WPA-PSK, WPA2-PSK
- WPA-EAP, WPA2-EAP
- TKIP, AES
- MAC address filtering
- SSID broadcast disable function
QUALITY OF SERVICE (QoS)
Wi-Fi Multimedia (WMM)
DEVICE MANAGEMENT
- Web-based management through Internet Explorer v.6 or later,
Netscape Navigator v.6 or later or other Java-enabled browser
RADIO & MODULATION SCHEMES
DQPSK, DBPSK, CCK, OFDM
OPERATION MODES
- Access Point
- Repeater
- Wireless Client
- Bridge
- Bridge with AP
- WISP Client Router
- WISP Repeater
D-Link DAP-1360 User Manual
Diagnostic LED
- Power
- WLAN
- LAN
POWER INPUT
5VDC 2.5A
External power adapter
97
Appendix D - Technical Specifications
DIMENSIONS
144 (W) x 109 (D) x 30 (H) mm (5.67 x 4.29 x 1.18 inches)
WEIGHT
229grams
OPERATING TEMPERATURE
0°C to 55° C (32°F to 131° F)
STORAGE TEMPERATURE
-10°C to 70°C (14°F to 158°F)
OPERATING HUMIDITY
10% to 90% non-condensing
STORAGE HUMIDITY
5% to 95% non-condensing
Actual data throughput will vary. Network conditions and environmental factors, including volume of network traffic, building materials and construction, and
network overhead lower actual data throughput rate.
D-Link DAP-1360 User Manual
98
Version 1.00
2009/02/19