Beko TLDA625 Operating instructions

Printed in Turkey
Part no: 48 2570 00 00
Revision no: 0
R E F R I G E R A T I O N
BEKO plc
Beko House
Caxton Way
Watford
Hertfordshire
WD18 8UF
Tel: 01923 654650
Fax: 01923 819653
e-mail: service@beko.co.uk
website: www.beko.co.uk
TLDA 625
11 cu.ft.
Tall Larder
Fridge
Operating
Instructions
Congratulations on your choice of a
service for many years.
quality Appliance which has been designed to give you
WARNING !
IMPORTANT !
DO NOT connect your appliance to the electricity supply until all packing and transit protectors have
been removed.
• Leave to stand for at least 4 hours before switching on to allow compressor oil to settle if transported
horizontally.
• If you are discarding an old refrigerator with a lock or latch fitted to the door, disable the lock/latch,
ensure that it is left in a safe condition to prevent the entrapment of young children.
• This fridge must only be used for its intended purpose i.e. the storing of edible foodstuff.
• Do not dispose of the appliance on a fire. At BEKO, the care and protection of our environment is
an ongoing commitment. This appliance which is among the latest range introduced is particularly
environment friendly. Your appliance contains non CFC / HFC natural substances in the cooling
system (Called R600a) and in the insulation (Called cyclopentane) which are potentially flammable
if exposed to fire. Therefore, take care not to damage, the cooling circuit / pipes of the appliance
in transportation and in use. In case of a damage do not expose the appliance to fire, potential
ignition source and immediately ventilate the room where the appliance is situated.
• We suggest you contact your local authority for disposal information and facilities available.
• We do not recommend use of this appliance in an unheated, cold room. See Instructions on page 5.
(E.g.: garage, conservatory, annex, shed, out-house etc.)
• To obtain the best possible performance and trouble free operation from your appliance it is very
important to carefully read these instructions.
• On delivery, check to make sure that the product is not damaged and that all the parts and accessories
are in perfect condition.
•Take care to ensure that the plug remains readily accessible. Do not use multiple adapter bar or
extension cable.
• Failure to observe these instructions may invalidate your right to free service during the guarantee
period.
WARNING- Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
WARNING- Do not use mechanical devices or other means to accelerate the defrosting process, other
than those recommended by the manufacturer.
WARNING- Do not damage the refrigerant circuit.
WARNING- Do not use electrical appliances inside the food storage compartments of the appliance,
unless they are of the type recommended by the manufacturer.
• We suggest you keep these instructions in a safe
place for easy reference.
Tall Larder Fridge
TLDA 625
PERFORMANCE
CONTENTS
PAGE
SAFETY FIRST / ELECTRICAL REQUIREMENTS
3
TRANSPORTATION INSTRUCTIONS
4
INSTALLATION INSTRUCTIONS
5
GETTING TO KNOW YOUR LARDER FRIDGE
CHILLER ZONE COMPARTMENT DRAWER
7
TEMPERATURE CONTROL AND ADJUSTMENT OF FRIDGE
8
9
STARTING
9
DEFROSTING
10
CLEANING AND CARE
REPLACING THE INTERIOR LIGHT BULB
12
1
A
170
290 lt. (10.2)
----290 lt. (10.2)
------------SN
39
11
12
DO'S AND DON'TS
PROBLEM SOLVING
Energy efficiency class
Energy consumption - Kwh/year
Net storage - vol fresh food ltrs (cu.ft.)
Net storage - vol frozen food ltrs (cu.ft.)
Total net vol - ltrs (cu.ft.)
Frozen food compartment rating
Conservation time from failure
Freezing capacity fresh food - kg
Climate class
Operating noise level dB(A)
6-7
13-14
REVERSING THE DOOR
15
GUARANTEE DETAILS
16
HOW TO OBTAIN SERVICE
2
ELECTRICAL REQUIREMENTS
Before you insert the plug into the wall socket make sure that the voltage and the
frequency shown in the rating plate inside the appliance corresponds to your
electricity supply. Rating plate is affixed on the left hand side of inner liner
We recommend that this appliance is connected to the mains supply via a
suitable switched and fused socket. The appliance must be positioned so that the
plug is accessible.
Should the mains lead of the appliance become damaged or should it need
replacing at any time, it must be replaced by a special purpose made mains lead
which can only be obtained from a BEKO Authorised Service Agent.
WARNING! THIS APPLIANCE MUST BE EARTHED
If the fitted moulded plug is not suitable for your socket, then the plug should be
cut off and an appropriate plug fitted. Destroy the old plug which is cut off as a
plug with bared cord could cause a shock hazard if inserted into a socket
elsewhere in the house.
The moulded plug on this appliance incorporates a 13 A fuse. Should the fuse
need to be replaced an ASTA approved BS 1362 fuse of the same rating must be
used. Do not forget to refit the fuse cover. In the event of losing the fuse cover the
plug must not be used until a replacement fuse cover has been fitted. Colour of
the replacement fuse cover must be the same colour as that visible on the pin face
of the plug. Fuse covers are available from any good electrical store.
2. Connect the blue (Neutral) wire
to the terminal in the plug
marked 'N' or coloured black.
6mm.
22mm.
CORD GRIP
FITTED WITH
BS 1362 13A FUSE ALWAYS
FIT BS 1362 REPLACEMENT
CARTRIDGE FUSE
green and yellow or green.
N
BLUE
OR
BLACK
FUSE
or coloured
12mm.
the symbol
L
BROWN
OR
RED
IMPORTANT : Care must be taken while cleaning / carrying the appliance to
avoid touching the bottom of the condenser metal wires at the back of the
appliance as you might injure your fingers and hands.
IMPORTANT : This appliance is not designed for stacking with any other
appliance.
Do not attempt to sit or stand on top of your appliance as it is not designed for
such use. You could injure yourself or damage the appliance.
6mm.
32mm.
1. Connect the green-yellow or
green (Earth) wire to the terminal
in the plug marked 'E' or with
GREEN &
YELLOW
OR
GREEN
6mm.
IMPORTANT! FITTING A DIFFERENT PLUG
As the colours of the wires in the
mains lead of this appliance may
not correspond with the coloured
markings identifying the terminals
in your plug proceed as follows:
(See diagram).
TRANSPORTATION INSTRUCTIONS
1. The appliance should be transported only in a vertical upright position. The
packing as supplied must be intact during transportation.
2. If during the course of transport the appliance has to be transported horizontally,
the product must only be laid on its left hand side (when facing the door
front) and it must not be operated for at least 4 hours to allow the system to
settle after the appliance is brought back to upright position.
3. Failure to comply with the above instructions could result in damage occurring.
to the appliance. The manufacturer will not be held responsible if these
instructions are disregarded.
4. The appliance must be protected against rain, moisture and other
atmospheric influences.
5. When positioning your appliance take care not to damage your flooring,
pipes, wall coverings etc. Do not move the appliance by pulling by the door
or handle.
6. Empty any water in the drain tray before moving. See section ‘Defrosting’ and
‘Care & cleaning’ for further information.
3. Connect the brown (Live) wire to
the terminal in the plug marked 'L'
or coloured red.
With alternative plugs a 13 A fuse must be fitted either in the plug or adaptor or
in the main fuse box.
If in doubt contact a qualified electrician.
3
"IMPORTANT: Make sure that mains cable is not caught under the appliance
during and after carrying / moving the appliance, to avoid the mains cable
becoming cut or damaged."
Do not allow children to play with the appliance or tamper with the controls.
BEKO plc declines to accept any liability should the instructions not be
followed.
4
IMPORTANT
INSTALLATION INSTRUCTIONS
1. The space in the room where the appliance is installed must not be smaller
than 10 cubic metres.
2. If possible avoid placing the appliance near cookers, radiators or in direct
sunlight as this will cause the compressor to run for long periods. If installed
next to a source of heat or refrigerator, maintain the following minimum side
clearances:
GETTING TO KNOW YOUR LARDER FRIDGE
1
11
12
2
3
11
4
5
From Cookers
From Radiators
From Refrigerators or Freezers
2" (50 mm)
12" (300 mm)
1" (25 mm)
4
11
Allow a minimum of 60 mm (2.4 inches) between the top of the fridge and the
ceiling or the underside of a wall cupboard.
3. Make sure that sufficient room is provided around the appliance to ensure free
air circulation.
4. Fit the two plastic wall spacers supplied
with the appliance rotating 1/4 turn to
the condenser at the back of the
refrigerator (see diagram).
5. The appliance should be located on a
smooth surface. The two front feet can be
adjusted as required. To ensure that
your appliance is standing upright adjust
the two front feet by turning clockwise or anti-clockwise, until the product is in
firm contact with the floor. Correct adjustment of feet avoids excessive
vibration and noise.
6. Refer to "Cleaning and Care" section to prepare your appliance for use.
7. This appliance has been designed to operate in ambient temperatures
beetween +10 and +32 degrees C (50 and 90 degrees F).Therefore if the
appliance is installed in an unheated / cold room (E.g.: Conservatory /
annex / shed / garage etc.) then the appliance may not operate and as a result
the storage time of food may be reduced.
8. A special receptacle is supplied to store the mains plug during transit.
The receptacle is fixed at the back of the
cabinet, on the right hand side of the
compressor. (See diagram) Gently remove
the plug from the receptacle. Never pull
the mains cord, you may damage the
appliance. In the case of transportation,
ensure you locate the plug in the receptacle
provided to avoid transit damage.
5
4
4
13
6
7
8
9
10
Arrangement Examples (See diagram).
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Front plastic trim
Interior light
Thermostat knob
Adjustable glass shelves
Wine rack
Chiller compartment flap
Chiller compartment drawer
Salad Crisper
Air grille
Adjustable front feet
Door shelves
Egg tray
Bottle rack
6
The following guidelines and recommendations are suggested to obtain the best
results and storage hygiene.
1.The larder fridge is suitable for the short term storage of fresh food and drinks.
2.Cooked dishes must be stored in airtight covered containers.
3.Fresh wrapped produce can be placed on the shelf. Fresh fruit and
vegetables should be cleaned and stored in the salad crisper bin.
4.Bottles can be placed upright in the door rack.
5.To store raw meat, wrap in polythene bags and place in the Chiller Zone
Compartment . Do not allow to come into contact with cooked food to avoid
contamination. For safety, only store raw meat for two to three days.
6.Keep the food packed, wrapped or covered. Allow hot food and beverages
to cool before placing them in the fridge. Do not store poisonous or dangerous
substances in the refrigerator. High proof alcohol must be stored upright in
sealed containers. Left over canned food should not be stored in the can.
7.Some fruit and vegetables suffer damage if kept at temperatures near 0
degrees centigrade. Therefore wrap pineapples, melon, cucumbers,
tomatoes and similar produce in polythene bags.
8.Do not leave frozen food at room temperature to thaw; the best way to defrost
food is to put it in the fridge to thaw slowly. Make sure you avoid defrosting
food or food juices drip onto other food.
9.For hygiene reasons, always wrap food using a suitable packaging material
before storing in your appliance to avoid contact with the appliance surface.
CHILLER ZONE COMPARTMENT DRAWER
(Also refer to Temperature Control and Adjusment of fridge on page 8.)
Chiller Zone Compartment Drawer is ideal for storage of fresh fish, meat and easily
perishable food like cooked chilled food. In order to best utilise this compartment,
we recommend the following;
Monitor the temperature using an accurate fridge thermometer to ensure that the
storage temperature is in the following range; approximately between -1.5 degrees
C and +3 degrees C. Below thermostat setting positions are suggested to start with;
Approximate ambient
Suggested thermostat
temperature in the room
where the appliance is (degrees C)
knob setting range *
10 degrees C
16 degrees C
20 degrees C
25 degrees C
32 degrees C
1 to 2
1 1/2 to 2 1/2
2 to 3
2 1/2 to 3 1/2
2 1/2 to 4
Warning!
Do not remove this glass shelf; otherwise
Chiller Zone Compartment will not function
to specifications.
TEMPERATURE CONTROL AND ADJUSTMENT OF FRIDGE
Operating temperatures are controlled by the thermostat knob (Fig. 1) and may
be set at any position between 1 and 5, 5 being the coldest position. Towards
5 you will obtain a colder fridge temperature and vice versa. Set the thermostat
knob to ensure an average of +5 °C (40°F) is achieved in the fridge and between
-1.5 °C and +3°C is achieved in the Chiller Zone Compartment after 24 hours.
(Fig. 2) shows how you can switch off the appliance completely: Turn the
thermostat knob to “0” (Zero) position.
The average temperature inside the fridge depends on the following factors:
• Ambient temperature in the room (seasonal changes)
• Frequency of door opening
• Placing hot food inside the product
• Position of the product
We recommend that you check the temperature with an accurate thermometer
to ensure that the storage compartments are kept to the desired temperature.
Remember you must take your reading very quickly since the thermometer
temperature will rise very rapidly after you remove it from the appliance.
Please remember each time the door is opened cold air escapes and the internal
temperature rises. Therefore never leave the door open and ensure it is closed
immediately after food is put in or removed.
In case of a temporary ice build up in the fridge compartment, reduce
the thermostat setting to 1. Once the ice build up disappears and the
appliance starts auto defrosting again as normal, then you may increase
the thermostat setting, if required.
If above settings could not maintain the required temperatures, then adjust the
thermostat knob accordingly; to obtain a colder temperature, turn the thermostat
knob towards 5 and vice versa.
*Also see factors affecting temperature inside the fridge on page 8 and adjust
it accordingly to suit your specific situation.
7
1
2
8
STARTING
Final Check
CLEANING AND CARE
** We recommend that you switch off the larder refrigerator at the socket outlet
and pull out the mains plug before cleaning.
Before you start using the refrigerator check that:
1. The front feet have been adjusted so the appliance is level.
2. The interior is dry and air can circulate freely.
3. Clean the interior as recommended under "CLEANING AND CARE."
4. Insert the plug into the wall socket and switch on the electricity supply.
When the door is open the interior light will come on.
5. You will hear a noise as the compressor starts up. The liquid and gases sealed
within the refrigeration system may also give rise to noise, whether the
compressor is running or not which is quite normal.
6.We recommend that you set the thermostat knob at 3 (three) and monitor the
temperature to ensure the appliance maintains desired storage temperatures
(See section Temperature Control and Adjustment).
7. Do not load the appliance immediately it is switched on. Wait
until the correct storage temperature has been reached. We
recommend that you check the temperature with an accurate
thermometer (see; Temperature Control and Adjustment).
Important Note :
Ice formation at the back is normal, do not worry. (See Defrosting)
** Use luke warm water to clean the cabinet of the refrigerator and wipe it dry.
** Use a damp cloth wrung out in a solution of one teaspoon of bicarbonate of
soda to one pint of water to clean the interior and wipe it dry.
** Make sure that no water enters the temperature control box.
** If the larder refrigerator is not going to be used for a long period of time
switch it off, remove all food, clean it and leave the door ajar.
** Any dust that gathers on the condenser, which is located at the back of the
appliance, should be removed once a year with a vacuum cleaner.
** Check door seals regularly to ensure they are clean and free from food
particles.
** Removal of door rack :
DEFROSTING
2
The larder refrigerator defrosts
1
automatically. The defrosting water runs to
the drain tube via a collection channel (1)
behind the Chiller Zone Compartment drawer
and is evaporated in a special container
at the back of the appliance (see diagrams).
Ensure that the container is fixed properly
Special Container
above the compressor.
During defrosting water droplets may form
at the back of the larder refrigerator where
concealed evaporator is located. Some
droplets may remain on the liner and
refreeze when defrosting is completed. Do
Compressor
not use pointed or sharp edged objects
such as knives, forks to remove the droplets which have refreezed.
If at any time the defrost water does not drain from the collection channel,remove
the Chiller Zone Compartment drawer and check to ensure that no food particles
have blocked the drain tube. The drain tube can be cleared by pushing the special
plastic plunger provided down the drain tube (2).
9
** Never use any sharp instruments or abrasive substances, soap, household
cleaner, detergent and wax polish for cleaning.
• To remove a door rack, remove all the contents and then simply push
the door tray upwards from the base.
** Make sure that the special plastic container (drain tray) at the back of the
appliance which collects defrost water is clean at all times. If you want to remove
the tray to clean it follow the instructions below :
• Switch off at the socket outlet and pull out the mains plug.
• Push the lug down with the tip of a screw driver & pull out firmly.
• Clean the drain tray and wipe it dry.
• Reassemble reversing the sequence and operations.
** Removal of Chiller Zone Compartment Drawer:
•Pull it out as far as possible and then lift up and remove it completely.
10
REPLACING THE INTERIOR LIGHT BULB (See diagram)
Should the light fail to work switch off at the socket outlet and pull out the mains
plug.
Use a cross headed screw driver to remove the light diffuser cover.
Then ensure the bulb is screwed in until it is secure in the bulb holder. Replace the
plug and switch on.
If the bulb functions, reassemble by reversing the above procedure, ensure the top
cover is in place.
If the light still fails to work obtain a replacement screw cap type 15 Watt (Max)
bulb from your local electrical store and then fit it as follows.
1. Switch off at the socket outlet and pull out the mains plug.
You may find it useful to remove shelves for easy access.
DO'S AND DON'TS
DoDoDoDoDoDoDoDoDoDo-
Clean your larder refrigerator regularly.
Keep raw meat and poultry below cooked food and dairy products and ideally in
the chiller zone compartment drawer.
Keep food for as short a time as possible and adhere to 'Best Before' and
"Use By" dates.
Take off any unusable leaves on vegetables and wipe off any soil.
Leave lettuce, cabbage, parsley and cauliflower on the stem.
Wrap cheese firstly in greaseproof paper and then in a polythene bag
excluding as much air as possible.
Wrap meat, fish and offal in polythene bags.
Wrap food which have a strong odour or can dry out in polythene bags
aluminium foil or place in airtight container.
Wrap bread well to keep it fresh.
Chill white wines, beer, lager and mineral water before serving.
6. Carefully dispose of the burnt-out light bulb immediately.
Don't- Store bananas in your fridge.
Don't- Store melon in your fridge. It can be chilled for short periods as long as it
is wrapped to avoid it flavouring other food.
Don't- Leave the door open for long periods as this will make the larder
refrigerator more costly to run.
Don't- Store poisonous or any dangerous substances in the larder refrigerator.
Your larder refrigerator has been designed for the storage of edible
foodstuffs only.
Don't- Consume food which has been stored for an excessive time in the
larder refrigerator.
Don't- Store cooked and fresh food together in the same container. They should
be packaged and stored separately.
Don't- Let defrosting food or food juices drip onto food in your larder
refrigerator.
"Replacement light bulb can easily be obtained from a good local electrical or DIY
PROBLEM SOLVING
2. Remove the light diffuser cover screw. Use cross-headed screw driver.
3. Pull off the light diffuser cover and remove the light bulb.
4. Replace the burnt-out light bulb.
5. Reassemble reversing the sequence and operations. First ensure the top of the
cover is in place.
If the appliance does not operate when switched on, check;
• The plug is inserted properly in the socket and that the power supply is on. (To
check the power supply to the socket, plug in another appliance)
• The fuse has blown/circuit breaker has tripped/main distribution switch has
been turned off.
• The temperature control has been set correctly.
• New plug is wired correctly if you have changed the fitted moulded plug.
store."
If the appliance is still not operating after the above checks, please refer to the section on
“How To Obtain Service”.
Please ensure that above checks have been made as a charge will be made if no
fault is found.
11
12
(17)
REVERSING THE DOOR
We recommend that you reverse the door before switching on for the first time.
5
Tools required: Small and medium size flat and cross-headed screwdrivers, a pair of pliers.
5
2
3
Spare Parts supplied in the plastic bag: The following parts, which are exclusively for left hand side fitted hinge operation
are supplied in a plastic bag with the appliance:
1
- Door top trim hinge covers – there are 2 different parts, one for each side of top trim.
We suggest you keep all the parts supplied in the plastic bag and also parts, which have been removed when reversing
the door, in a safe place for possible future, re-use.
IMPORTANT: We suggest you ask somebody to help you when moving the appliance around and to hold the door when
removing / re-fitting hinges and the door to avoid any injury and damage to the product.
6
4
Please refer to diagrams supplied. To follow numbers in brackets below, refer to the main diagram.
1.
2.
3.
456.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
Switch off the appliance at the socket outlet and pull out the mains plug.
Remove all loose items and fittings and food inside the appliance.
Gently prise off plastic hinge covers on both sides of front top panel using a small flat-headed screwdriver. (1-2)
Unscrew the bolts of the top hinge and remove top hinge. (3)
Remove door carefully off the bottom hinge and stand door upright in a safe place.(4)
Gently prise off plastic hinge cover on door top trim. Fit the other door top trim plastic off hinge cover supplied in the
plastic bag.(5)
Gently tilt the appliance back against a strong wall on its rear side sufficiently to allow the lower hinge to be removed.
Take care to protect the appliance, your wall and floor coverings. You can utilise the original packaging to do this.
Once you tilt the appliance back, check to make sure the appliance is completely stable and safe before you carry
on. (6)
Remove the kick plate by pulling it back.(7)
Unscrew and remove the adjustable foot bracket if required remove foot.(8)
Unscrew and remove the bottom hinge.(9)
Unscrew and remove the bottom hinge door stopper and bushing and reposition them on the other side while rotating
the bushing 180°.(10)
Unscrew and remove the bottom hinge pin using a pair of pliers and fix it to the hole next to its original position. (11)
Fit the bottom hinge to the cabinet as shown in the figure.(12)
Fit the adjustable foot bracket as shown in the figure.(13)
Reposition the kick plate plastic cover on the other side.(14)
Fit the kick plate.(15)
Locate and re-fit door to bottom hinge pin.(16)
Rotate the top hinge 180°. Unscrew the hinge pin and re-tighten it to the
opposite side. (17)
Re-fit the upper hinge on the opposite side by using a flat headed screwdriver.(18)
Fit front top panel plastic hinge covers on the opposite sides.(19)
Remove the handle cover gently taking care not to damage the appliance.(20)
Unscrew and remove the handle (21). Do not unscrew the yellow coloured screws!
Rotate 180 degrees and fit handle to the other side after removing hole plugs gently.(22,23)
Fit the handle cover.(24)
Adjust the two front feet if necessary.
Check that door opens and closes easily, it is aligned correctly and there are no gaps allowing air into the cabinet. If
there are gaps between the door seal and the cabinet, adjust the door seal by gently pulling away from the door using
fingers.
Check that all the hinge screws are tightened. Avoid over tightening the screws.
Put all items, fittings back in the appliance.
Wait for at least 4 hours to allow the system to settle before switching on.
Once the correct storage temperatures have been reached in the appliance, put back all the food.
13
45 °
9
7
10
8
26
19
18
17
180°
19
23
21
20
22
16
13
12
11
15
14
14
24
GUARANTEE DETAILS
HOW TO OBTAIN SERVICE
Your new Beko product is guaranteed against the cost of breakdown repairs for
twelve months from the date of the original purchase.
Please keep your purchase receipt or other proof of purchase in a safe place;
you will need to have it should the product require attention under guarantee.
What is covered?
• Repairs necessary as a result of faulty materials, defective components or
manufacturing defect.
• The cost of functional replacement parts, but excluding consumable items.
• The labour costs of a Beko approved repairer to carry out the repair.
You should also complete the details below; it will help us assist you when requesting
service. (The model number is printed on the Instruction Booklet and the serial
number is printed on the Rating Label affixed to the appliance)
What is not covered?
• Transit, delivery or accidental damage or misuse and abuse.
• Cabinet or appearance parts, including knobs, flaps, handles or container
lids.
• Accessories or consumable items including but not limited to, ice trays, scrapers,
cutlery baskets, filters and light bulbs.
• Repairs required as a result of unauthorised repair or inexpert installation that
fails to meet the requirements contained in the user instruction book.
• Repairs to products used on commercial or non-residential household premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is often
included within your household contents insurance policy, or may be available
separately from your retailer).
Important notes.
• Your Beko product is designed and built for domestic household use only.
• The guarantee will be void if the product is installed or used in commercial
or non-residential domestic household premises.
• The product must be correctly installed, located and operated in accordance
with the instructions contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Installer
is recommended for all Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a CORGI (or BORD GAIS) registered
Gas Installer.
• The guarantee is given only within the boundaries of the United Kingdom and
the Republic of Ireland.
• The guarantee is applicable only to new products and is not transferable if the
product is resold.
• Beko disclaims any liability for incidental or consequential damages.
The guarantee does not in anyway diminish your statutory or legal rights.
15
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number below
UK Mainland & Northern Ireland
Fridges & Freezers
Electric Cookers
Gas & Dual Fuel Cookers
Washing Machines
& Dishwashers
0870 241 0638
0870 241 1320
0870 241 1321
0870 241 0357
Republic of Ireland
All Refrigeration, All Cookers
Washing Machines & Dishwashers
01 862 3411
Before requesting service please check the trouble-shooting guide in the Operating
Instructions as a charge may be levied where no fault is found even though your
product may still be under guarantee.
Service once the manufacturers guarantee has expired.
If you have purchased an extended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise please
call the appropriate number above where service can be obtained at a charge.
Should you experience any difficulty in obtaining service please contact the Beko
Customer Help-Line.
Tel: 0870 774 1050 e-mail: service@beko.co.uk
16