Z8NH-D12
Z8PH-D12/IFB
Z8PH-D12 SE/QDR
Motherboard
Z8NH-D12 Series
E5743
First Edition V1
March 2010
Copyright © 2010 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any form or by any means,
except documentation kept by the purchaser for backup purposes, without the express written permission
of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless
such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the
product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS, ITS
DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS,
LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE),
EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY
DEFECT OR ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered trademarks or
copyrights of their respective companies, and are used only for identification or explanation and to the
owners’ benefit, without intent to infringe.
ii
Contents
Notices......................................................................................................... vii
Safety information..................................................................................... viii
About this guide.......................................................................................... ix
Typography................................................................................................... x
Z8NH-D12 Series specifications summary................................................ xi
Chapter 1:
Product introduction
1.1
Welcome!....................................................................................... 1-3
1.3
Serial number label....................................................................... 1-4
1.2
1.4
Package contents.......................................................................... 1-3
Special features............................................................................. 1-4
1.4.1
Product highlights............................................................ 1-4
1.4.2
Innovative ASUS features................................................ 1-6
Chapter 2:
2.1
2.2
2.3
2.4
2.5
Hardware information
Before you proceed...................................................................... 2-3
Motherboard overview.................................................................. 2-5
2.2.1
Placement direction......................................................... 2-5
2.2.2
Screw holes..................................................................... 2-5
2.2.4
Motherboard layouts........................................................ 2-6
2.2.5
Layout contents................................................................ 2-9
Central Processing Unit (CPU).................................................. 2-11
2.3.1
Installing the CPU...........................................................2-11
2.3.2
Installing the CPU heatsink and fan............................... 2-14
System memory.......................................................................... 2-16
2.4.1
Overview........................................................................ 2-16
2.4.2
Memory Configurations.................................................. 2-17
2.4.3
Installing a DIMM........................................................... 2-18
2.4.4
Removing a DIMM......................................................... 2-18
Expansion slots........................................................................... 2-19
2.5.1
Installing an expansion card.......................................... 2-19
2.5.2
Configuring an expansion card...................................... 2-19
2.5.3
Interrupt assignments.................................................... 2-20
2.5.4
PCI Express x16 slot (x16 link)...................................... 2-21
2.5.5
Installing ASMB4 management board............................ 2-21
iii
Contents
2.6
2.7
Jumpers....................................................................................... 2-22
Connectors.................................................................................. 2-28
2.7.1
Rear panel connectors................................................... 2-28
2.7.2
Internal connectors........................................................ 2-30
Chapter 3:
3.1
3.2
Powering off the computer........................................................... 3-4
3.2.1
Using the OS shut down function..................................... 3-4
3.2.2
Using the dual function power switch............................... 3-4
Chapter 4:
4.1
4.2
4.3
4.4
iv
Powering up
Starting up for the first time......................................................... 3-3
BIOS setup
Managing and updating your BIOS............................................. 4-3
4.1.1
AFUDOS utility................................................................. 4-3
4.1.2
ASUS CrashFree BIOS 3 utility....................................... 4-6
BIOS setup program..................................................................... 4-7
4.2.1
BIOS menu screen........................................................... 4-8
4.2.2
Menu bar.......................................................................... 4-8
4.2.3
Navigation keys................................................................ 4-8
4.2.4
Menu items...................................................................... 4-9
4.2.5
Sub-menu items............................................................... 4-9
4.2.6
Configuration fields.......................................................... 4-9
4.2.7
Pop-up window................................................................ 4-9
4.2.8
Scroll bar.......................................................................... 4-9
4.2.9
General help.................................................................... 4-9
Main menu................................................................................... 4-10
4.3.1
System Time [xx:xx:xx].................................................. 4-10
4.3.2
System Date [Day xx/xx/xxxx]........................................ 4-10
4.3.3
SATA1—4....................................................................... 4-10
4.3.4
IDE Configuration........................................................... 4-12
4.3.5
AHCI Configuration........................................................ 4-13
4.3.6
System Information........................................................ 4-14
Advanced menu.......................................................................... 4-16
4.4.1
CPU Configuration......................................................... 4-16
4.4.2
Chipset Configuration.................................................... 4-20
Contents
4.5
4.4.3
Legacy Device Configuration......................................... 4-24
4.4.4
USB Configuration......................................................... 4-25
4.4.5
PCIPnP Configuration.................................................... 4-26
4.4.6
Power On Configuration................................................. 4-27
4.4.7
Event Log Configuration................................................ 4-28
4.4.8
Hardware Monitor.......................................................... 4-28
4.4.9
I/O Virtualization............................................................. 4-30
4.4.10
PCI Express Configuration............................................. 4-30
4.4.11
ACPI Configuration........................................................ 4-31
Server menu................................................................................ 4-33
4.5.1
4.6
4.7
Remote Access Configuration........................................ 4-33
Boot menu................................................................................... 4-35
4.6.1
Boot Device Priority....................................................... 4-35
4.6.2
Hard Disk Drives; CDROM Drives................................. 4-35
4.6.3
Boot Settings Configuration........................................... 4-36
4.6.4
Security.......................................................................... 4-37
Exit menu..................................................................................... 4-39
Exit & Save Changes ................................................................... 4-39
Exit & Discard Changes................................................................ 4-39
Discard Changes........................................................................... 4-39
Load Setup Defaults .................................................................... 4-39
Chapter 5:
5.1
5.2
RAID configuration
Setting up RAID............................................................................. 5-3
5.1.1
RAID definitions............................................................... 5-3
5.1.2
Installing hard disk drives................................................. 5-4
5.1.3
Setting the RAID item in BIOS......................................... 5-4
5.1.4
RAID configuration utilities............................................... 5-4
LSI Software RAID Configuration Utility..................................... 5-5
5.2.1
Creating a RAID set......................................................... 5-6
5.2.2
Adding or viewing a RAID configuration........................ 5-12
5.2.3
Initializing the virtual drives............................................ 5-13
5.2.4
Rebuilding failed drives.................................................. 5-17
5.2.5
Checking the drives for data consistency...................... 5-19
5.2.6
Deleting a RAID configuration........................................ 5-22
Contents
5.3
5.2.7
Selecting the boot drive from a RAID set....................... 5-23
5.2.8
Enabling WriteCache..................................................... 5-24
Intel® Matrix Storage Manager Option ROM Utility.................. 5-25
5.3.1
Creating a RAID set....................................................... 5-26
5.3.2
Creating a Recovery set................................................ 5-27
5.3.3
Deleting a RAID set....................................................... 5-29
5.3.4
Resetting disks to Non-RAID......................................... 5-30
5.3.5
Recovery Volume Options............................................. 5-31
5.3.6
Exiting the Intel® Matrix Storage Manager..................... 5-32
5.3.7
Rebuilding the RAID...................................................... 5-32
5.3.8
Setting the Boot array in the BIOS Setup Utility............. 5-34
Driver installation
6.1
RAID driver installation................................................................ 6-3
6.1.1
Creating a RAID driver disk............................................. 6-3
6.1.2
Windows® OS................................................................... 6-6
6.1.3
Red Hat® Enterprise Linux OS......................................... 6-9
6.1.4
SUSE Linux Enterprise Server OS................................ 6-17
6.2
Intel chipset device software installation................................. 6-19
6.4
Display driver installation.......................................................... 6-27
6.3
6.5
6.6
LAN driver installation................................................................ 6-23
Mellanox ConnectX DDR and ConnectX2 QDR PCI Gen2
Channel Adapter driver installation.......................................... 6-30
6.5.1
Windows operating system............................................ 6-30
6.5.2
Red Hat® Enterprise Linux OS..............................6-34
Management applications and utilities installation................. 6-37
6.6.1
Running the support DVD.............................................. 6-37
6.6.2
Drivers menu.................................................................. 6-37
6.6.3
Utilities menu................................................................. 6-38
6.6.4
Make disk menu............................................................. 6-38
6.6.5
Contact information........................................................ 6-38
Reference information
A.1
Z8NH-D12 block diagram..............................................................A-3
A.3
Z8PH-D12 SE/QDR block diagram...............................................A-5
A.2
vi
Z8PH-D12/IFB block diagram.......................................................A-4
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’
s instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
REACH
Complying with the REACH (Registration, Evaluation, Authorization, and Restriction
of Chemicals) regulatory framework, we published the chemical substances in our
products at ASUS REACH website at http://green.asus.com/english/REACH.htm.
vii
Safety information
Electrical safety
•
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
•
When adding or removing devices to or from the system, ensure that the
power cables for the devices are unplugged before the signal cables are
connected. If possible, disconnect all power cables from the existing system
before you add a device.
•
Before connecting or removing signal cables from the motherboard, ensure
that all power cables are unplugged.
•
Seek professional assistance before using an adapter or extension cord.
These devices could interrupt the grounding circuit.
•
Make sure that your power supply is set to the correct voltage in your area.
If you are not sure about the voltage of the electrical outlet you are using,
contact your local power company.
•
If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
•
Before installing the motherboard and adding devices on it, carefully read all
the manuals that came with the package.
•
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
•
Avoid dust, humidity, and temperature extremes. Do not place the product in
any area where it may become wet.
•
Place the product on a stable surface.
•
If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Check local regulations for disposal of electronic
products.
viii
About this guide
This user guide contains the information you need when installing and configuring
the motherboard.
How this guide is organized
This user guide contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technologies it supports.
•
Chapter 2: Hardware information
This chapter lists the hardware setup procedures that you have to perform
when installing system components. It includes description of the switches,
jumpers, and connectors on the motherboard.
•
Chapter 3: Powering up
This chapter describes the power up sequence and ways of shutting down
the system.
•
Chapter 4: BIOS setup
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
•
Chapter 5: RAID configuration
This chapter provides instructions for setting up, creating, and configuring
RAID sets using the available utilities.
•
Chapter 6: Driver installation
This chapter provides instructions for installing the necessary drivers for
different system components.
•
Appendix: Reference information
This appendix includes additional information that you may refer to when
configuring the motherboard.
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware and
software products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as warranty
flyers, that may have been added by your dealer. These documents are not
part of the standard package.
ix
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
DANGER/WARNING: Information to prevent injury to yourself
when trying to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to help you complete a
task.
Typography
Bold text
Italics <Key> Indicates a menu or an item to select.
<Key1+Key2+Key3>
If you must press two or more keys
simultaneously, the key names are linked with
a plus sign (+).
Example: <Ctrl+Alt+D>
Command
Means that you must type the command
exactly as shown, then supply the required
item or value enclosed in brackets.
Example: At the DOS prompt, type the
command line: format A:/S
Used to emphasize a word or a phrase.
Keys enclosed in the less-than and greaterthan sign means that you must press the
enclosed key.
Example: <Enter> means that you must press
the Enter or Return key.
Z8NH-D12 Series specifications summary
Model Name
Z8NH-D12
Processor Support / System Bus
2 * socket 1366
Six/Quad-Core Intel® Xeon® X5600 Series
(130W/95W)
Six/Quad-Core Intel® Xeon® L5600 Series
(60W/40W)
Quad-Core Intel® Xeon® E5600 Series (80W)
Quad-Core Intel® Xeon® X5500 Series (95W)
Quad-Core Intel® Xeon® E5500 Series (80W)
Quad-Core Intel® Xeon® L5500 Series
(60W/38W)
QPI 4.8 / 5.86 / 6.4 GT/s
Intel® 5500
Intel® 5520
Intel® 5520
chipset IOH
chipset IOH
chipset IOH
Intel® ICH10R I/O Controller
Core Logic
Form Factor
ASUS Features
Fan Speed
Control
Rack Ready
(Rack and
Pedestal dual
use)
ASWM
Total Slots
Capacity
Z8PH-D12/IFB Z8PH-D12
SE/QDR
Mellanox
ConnectX
MT25408
DDR 20Gbps
controller
Mellanox
ConnectX-2
MT25418 B0
QDR 40Gbps
controller
6.3” x 16.7”
V
V
V
V
V
V
V
V
V
12 (3-channel per CPU, 6 DIMM per CPU)
Maximum up to 96GB (RDIMM)
Maximum up to 48GB (UDIMM)
Memory Type
DDR3 800/1066/1333 Reg DIMM/ Unbuffered
DIMM with ECC
Memory Size
1GB, 2GB, 4GB, 8GB* (RDIMM)
1GB, 2GB, 4GB (UDIMM)
Expansion Slots
Total PCI/PCI-X/ 1
1
1
(follow SSI Loacation #) PCI-E Slots
Slot Loacation 6 1 * PCI-E x16 (Gen2 x16 Link)
Storage
SATA Controller Intel® ICH10R:
4 SATA2 300MB/s ports
Intel Matrix Storage (for Windows only)
(Support software RAID 0, 1, 10 & 5)
LSI® MegaRAID (for Linux/Windows)
(Support software RAID 0, 1, 10)
Memory
xi
Z8NH-D12 Series specifications summary
Networking
LAN
2 * Intel 82574L + 1 * Management LAN
1 * Single Port 1 * Single Port
DDR Infiniband QDR Infiniband
20Gbps with 40Gbps
CX4 interface with QSFP
interface
Graphic
VGA
Aspeed AST2050 8MB
Onboard I/O
PSU Connector 2 * 20-pin 12V power connector
Connectors
1 * 4-pin Molex connector for hard disk drive
USB Connectors 2 (One for internal Type A USB connector )
Fan Header
4 * 4pin (4pin FAN Only)
SMBus
2
2
2
Front LAN LED 2
2
2
Rear I/O Connectors
External Serial 1
1
1
Port
External USB
2
2
2
Port
VGA Port
1
1
1
RJ-45
2 + 1 Management Port
Management Solution Software
ASWM
Out of Band
Optional ASMB4-iKVM for KVM-over-IP support
Remote
Management
Monitoring
CPU
V
V
V
Temperature
FAN RPM
V
V
V
Environment
Operation temperature: 10℃—35℃
Non operation temperature: -40℃—70℃
Non operation humidity: 20%—90%
( Non condensing)
Specifications are subject to change without notice.
•
The 20-pin proprietory power connectors are not compatible with SSI power
supply. USE THE PROPRIETARY POWER SUPPLY ONLY; otherwise you
may damage the motherboard.
•
The 4-pin Molex connector is designed for hard disk drive only. DO NOT
connect other 4-pin power connectors of the power supply unit (PSU) to this
connector.
DO NOT touch the Northbridge chipset! The Northbridge chipset may become
overheated. Remember to provide sufficient air flow to keep the system stable.
xii
This chapter describes the motherboard
features and the new technologies it supports.
1
Product
introduction
Chapter summary
1
1.1
Welcome!....................................................................................... 1-3
1.3
Serial number label....................................................................... 1-4
1.2
1.4
Package contents.......................................................................... 1-3
Special features............................................................................. 1-4
ASUS Z8NH-D12 Series
1.1
Welcome!
Thank you for buying an ASUS® Z8NH-D12 Series motherboard!
The motherboard delivers a host of new features and latest technologies, making it
another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it, check the
items in your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Standard Bulk Pack
Application CD Support CD
Documentation User Guide
Packing Qty.
Z8NH-D12 Series
1
1
10pcs per carton
If any of the above items is damaged or missing, contact your retailer.
ASUS Z8NH-D12 Series
1-3
1.3
Serial number label
Before requesting support from the ASUS Technical Support team, you must take
note of the motherboard's serial number containing 13 characters xxS2xxxxxxxxx
shown as the figure below. With the correct serial number of the product, ASUS
Technical Support team members can then offer a quicker and satisfying solution
to your problems.
Z8NH-D12
xxS2xxxxxxxxx
1.4
Special features
1.4.1
Product highlights
Made
in
China
合格
Latest processor technology
This motherboard supports the latest Intel Xeon 5500 series processors in LGA
1366 package with integrated memory controller to support 3-channel (6 DIMM per
CPU) DDR3 memory. Intel Xeon 5500 series processor supports Intel QuickPath
Interconnect (QPI) with a system bus of up to 6.4GT/s and a max bandwidth of up
to 25.6GB/s. Intel Xeon 5500 series processor is the one of the most powerful and
energy-efficient CPUs in the world.
Intel Turbo Boost
Intel Turbo Boost dynamically reroute power to improve performance. The
processor will automatically overclock as long as the CPU temperature is allowed.
Intel Hyper Threading
The thread-level parallelism on each processor makes more efficient use of the
processor resources, higher processing throughout and improved performance on
today's multi-threaded software.
Intel® EM64T
The motherboard supports Intel® processors with the Intel® EM64T (Extended
Memory 64 Technology). The Intel® EM64T feature allows your computer to run on
64-bit operating systems and access larger amounts of system memory for faster
and more efficient computing.
1-4
Chapter 1: Product introduction
DDR3 memory support
The Z8NH-D12 Series supports UDIMM and RDIMM DDR3 memory that features
data transfer rates of 1333/1066 MHZ to meet the higher bandwidth requirements
of server and workstation applications. The 3-channel DDR3 architecture boosts
system performance, eliminating bottlenecks with peak bandwidth of up to 17GB/s.
Furthermore, the supply voltage for the memory is reduced form 1.8 V for DDR2 to
just 1.5V for DDR3. This voltage reduction limits the power consumption and heat
generation of DDR3 which makes it an ideal memory solution.
PCIe 2.0
This motherboard supports the latest PCIe 2.0 device for twice the current speed
and bandwidth. This enhances system performance while still providing backward
compatibility to PCIe 1.0 devices.
82574L LAN Solution
The motherboard comes with dual Gigabit LAN controllers and ports which provide
a total solution for your networking needs. The onboard Intel 82574L Gigabit LAN
controllers use the PCI Express interface and could achieve network throughput
close to Gigabit bandwidth.
Enhanced Intel SpeedStep Technology (EIST)
The Enhanced Intel SpeedStep Technology (EIST) intelligently manages the
CPU resources by automatically adjusting the CPU voltage and core frequency
depending on the CPU loading and system speed or power requirement.
Serial ATA II technology
The motherboard supports the Serial ATA II 3 Gb/s technology through the Serial
ATA interface and Intel ICH10R chipset. The Serial ATA II specification provides
twice the bandwidth of the current Serial ATA products with a host of new
features, including Native Command Queuing (NCQ), Power Management (PM)
Implementation Algorithm, and Hot Swap. Serial ATA allows thinner, more flexible
cables with lower pin count and reduced voltage requirements.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0 specification,
dramatically increasing the connection speed from the 12 Mbps bandwidth on USB
1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is backward compatible with USB 1.1.
ASUS Z8NH-D12 Series
1-5
Temperature, fan, and voltage monitoring
The CPU temperature is monitored to prevent overheating and damage. The
system fan rotations per minute (RPM) is monitored for timely failure detection.
The chip monitors the voltage levels to ensure stable supply of current for critical
components.
100% Japan-made Conductive Polymer Capacitors
This motherboard uses all high-quality conductive polymer capacitors for durability,
improved lifespan, and enhanced thermal capacity.
1.4.2
Innovative ASUS features
ASUS EPU
With current trends leaning towards power efficiency, the Z8NH-D12 Series is
equipped with the ASUS exclusive EPU technology to provide total system power
saving by detecting current CPU loadings and intelligently moderating power in
real-time.
1-6
Chapter 1: Product introduction
This chapter lists the hardware setup
procedures that you have to perform
when installing system components. It
includes description of the jumpers and
connectors on the motherboard.
2
Hardware
information
Chapter summary
2
2.1
Before you proceed...................................................................... 2-3
2.3
Central Processing Unit (CPU).................................................. 2-11
2.2
2.4
2.5
2.6
2.7
Motherboard overview.................................................................. 2-5
System memory.......................................................................... 2-16
Expansion slots........................................................................... 2-19
Jumpers....................................................................................... 2-22
Connectors.................................................................................. 2-28
ASUS Z8NH-D12 Series
2.1
Before you proceed
Take note of the following precautions before you install motherboard components or change
any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or a metal
object, such as the power supply case, before handling components to
avoid damaging them due to static electricity.
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded antistatic
pad or in the bag that came with the component.
•
Before you install or remove any component, ensure that the power supply
is switched off or the power cord is detached from the power supply. Failure
to do so may cause severe damage to the motherboard, peripherals, and/or
components.
Onboard LED
1.
Standby Power LED
The motherboard comes with a standby power LED. The green LED lights up
to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a
reminder that you should shut down the system and unplug the power cable
before removing or plugging in any motherboard component. The illustration
below shows the location of the onboard LED.
ASUS Z8NH-D12 Series
2-3
2-4
2.
CPU warning LED (ERR_CPU1, ERR_CPU2)
The CPU warning LEDs light up to indicate that an impending failure of the
corresponding CPU.
Chapter 2: Hardware information
2.2
Motherboard overview
Before you install the motherboard, study the configuration of your chassis to
ensure that the motherboard fits into it.
To optimize the motherboard features, we highly recommend that you install it in an
SSI EEB 1.1 compliant chassis.
Ensure to unplug the chassis power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components!
2.2.1
Placement direction
When installing the motherboard, ensure that you place it into the chassis in the
correct orientation. The edge with external ports goes to the rear part of the chassis
as indicated in the image below.
2.2.2
Screw holes
Place eight (8) screws into the holes indicated by circles to secure the motherboard
to the chassis.
DO NOT overtighten the screws! Doing so can damage the motherboard.
Place this side towards
the rear of the chassis
ASUS Z8NH-D12 Series
2-5
2.2.4
Motherboard layouts
Z8NH-D12
2-6
Chapter 2: Hardware information
Z8PH-D12/IFB
ASUS Z8NH-D12 Series
2-7
Z8PH-D12 SE/QDR
2-8
Chapter 2: Hardware information
2.2.5
Layout contents
Slots/Soocket
Page
1.
CPU sockets
2-10
2.
DDR3 sockets
2-15
3.
PCI Express x 16 slot
2-20
Jumpers
Page
1.
Clear RTC RAM (CLRTC1)
2-21
2.
VGA controller setting (3-pin VGA_SW1))
2-22
3.
DDR3 voltage control setting
(4-pin LVDDR3_SEL1; LVDDR3_SEL2)
2-22
4.
LAN controller setting (3-pin LAN_SW1, LAN_SW2)
2-23
5.
Intel ICH10R SATA port S/W RAID setting (3-pin RAID_SEL1)
2-23
6.
Force BIOS recovery setting (3-pin RECOVERY1)
2-24
Rear panel connectors
Page
1.
RJ-45 port for iKVM
2-25
2.
USB 2.0 ports 1 and 2
2-25
3.
LAN 1 (RJ-45) port
2-25
4.
LAN 2 (RJ-45) port
2-25
5.
Serial (COM1) port
2-25
6.
Video Graphics Adapter port
2-25
7.
Location LED
2-25
ASUS Z8NH-D12 Series
2-9
2-10
Internal connectors
Page
1.
Serial ATA connectors
(7-pin SATA1, SATA2, SATA3, SATA4)
2-26
2.
USB connector (5-1 pin USB3, A-Type USB4)
2-27
3.
Thermal sensor cable connectors (3-pin TR1, TR2)
2-27
4.
Front fan connectors
(4-pin FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4)
2-28
5.
LPC debug card connector (14-1 pin LPC1)
2-29
6.
Serial General Purpose Input/Output connector (6-1 pin SGPIO1)
2-29
7.
BMC header (BMC_FW1)
2-30
8.
Power Supply SMBus connectors (6-1 pin JP1; JP2)
2-30
9.
Proprietary power connectors
(20-pin PWR1, 20-pin PWR2, 4-pin PWR3)
2-31
10.
System panel connector (20-1 pin PANEL1)
2-32
11.
Auxiliary panel connector (20-2 pin AUX_PANEL1)
2-33
Chapter 2: Hardware information
2.3
Central Processing Unit (CPU)
The motherboard comes with dual surface mount LGA 1366 Socket designed for
the Intel® Xeon 5500 series CPU in the Land Grid Array (LGA) package.
2.3.1
•
Upon purchase of the motherboard, ensure that the PnP cap is on
the socket and the socket contacts are not bent. Contact your retailer
immediately if the PnP cap is missing, or if you see any damage to the PnP
cap/socket contacts/motherboard components. ASUS shoulders the repair
cost only if the damage is shipment/transit-related.
•
Keep the cap after installing the motherboard. ASUS will process Return
Merchandise Authorization (RMA) requests only if the motherboard comes
with the cap on the Socket 1366.
•
The product warranty does not cover damage to the socket contacts
resulting from incorrect CPU installation/removal, or misplacement/loss/
incorrect removal of the PnP cap.
Installing the CPU
To install a CPU:
1.
Locate the CPU socket on the motherboard.
Before installing the CPU, ensure that the socket box is facing toward you and
the load lever is on your left.
ASUS Z8NH-D12 Series
2-11
2.
Press the load lever with your
thumb (A), then move it to the left
(B) until it is released from the
retention tab.
To prevent damage to the socket
pins, do not remove the PnP cap
unless you are installing a CPU.
3.
Lift the load lever in the direction of
the arrow to a 135º angle.
4.
Lift the load plate with your thumb
and forefinger to a 100º angle.
Retention tab
A
B
Load lever
Load plate
4
3
5.
Remove the PnP cap from the CPU
socket.
PnP cap
2-12
Chapter 2: Hardware information
6.
Position the CPU over the socket,
ensuring that the gold triangle is on
the bottom‑left corner of the socket,
and then fit the socket alignment key
into the CPU notch.
The CPU fits in only one correct
orientation. DO NOT force the
CPU into the socket to prevent
bending the connectors on the
socket and damaging the CPU!
Gold
triangle
mark
CPU notch
Alignment key
7.
Apply some Thermal Interface
Material to the exposed area of
the CPU that the heatsink will be
in contact with, ensuring that it is
spread in an even thin layer.
Some heatsinks come with
pre-applied Thermal Interface
Material. If so, skip this step.
The Thermal Interface Material is toxic. DO NOT eat the Thermal Interface
Material. If it gets into your eyes or touches your skin, ensure that you wash it
off immediately and seek professional medical help.
To prevent contaminating the Thermal Interface Material, DO NOT spread the
Thermal Interface Material with your finger directly.
ASUS Z8NH-D12 Series
2-13
2.3.2
Installing the CPU heatsink and fan
The Intel Xeon 5500 series processors require a specially designed heatsink to
ensure optimum thermal condition and performance.
•
Ensure to use qualified heatsink assembly only.
•
Ensure that you have applied the thermal grease to the top of the CPU
before installing the heatsink and fan.
Follow these steps to install the CPU heatsink and fan.
1.
Orient and place the heatsink on top of the installed CPU, ensuring that the
screw holes are matched with the heatsink standoffs.
2.
Use a Phillips screwdriver to tighten the four heatsink screws in a diagonal
sequence.
Ensure that the heatsink is not skewed or tilted, otherwise the CPU will overheat.
2-14
Chapter 2: Hardware information
3.
Connect the fan cable to any of the the 4‑pin connectors.
3.���������������������������������������������������������������������������������
Repeat steps 1 to 3 to install the other heatsink if you have installed a second
CPU, then connect the fan cable to another 4‑pin connector.
ASUS Z8NH-D12 Series
2-15
2.4
System memory
2.4.1
Overview
The motherboard comes with twelve (12) Double Data Rate 3 (DDR3) Dual Inline
Memory Modules (DIMM) sockets.
A DDR3 module has the same physical dimensions as a DDR2 DIMM but is
notched differently to prevent installation on a DDR2 DIMM socket. DDR3 modules
are developed for better performance with less power consumption.
The figure illustrates the location of the DDR3 DIMM sockets:
2-16
Chapter 2: Hardware information
2.4.2
Memory Configurations
You may install 1 GB, 2 GB, 4 GB, or 8GB registered ECC/unbuffered ECC DDR3
DIMMs into the DIMM sockets using the memory configurations in this section.
Always install DIMMs with the same CAS latency. For optimum compatibility, it
is recommended that you obtain memory modules from the same vendor.
Memory population table
CPU 1 Configuration
DIMM_A2
1 DIMMs
-2 DIMMs
-3 DIMMs
-4 DIMMs
6 DIMMs
CPU 2 Configuration
DIMM_D2
1 DIMMs
-2 DIMMs
-3 DIMMs
-4 DIMMs
6 DIMMs
ASUS Z8NH-D12 Series
DIMM_A1
DIMM_B2
-----
DIMM_B1
--
DIMM_C2
-----
DIMM_C1
---
DIMM_D1
DIMM_E2
-----
DIMM_E1
--
DIMM_F2
-----
DIMM_F1
---
2-17
2.4.3
Installing a DIMM
Unplug the power supply before adding or removing DIMMs or other
system components. Failure to do so can cause severe damage to both the
motherboard and the components.
2
To install a DIMM:
1.
Unlock a DIMM socket by pressing
the retaining clips outward.
2.
Align a DIMM on the socket
such that the notch on the DIMM
matches the break on the socket.
3.
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
3
DDR3 DIMM notch
1
1
Unlocked retaining clip
2.4.4
•
A DDR3 DIMM is keyed with a notch so that it fits in only one direction. DO
NOT force a DIMM into a socket to avoid damaging the DIMM.
•
The DDR3 DIMM sockets do not support DDR and DDR2 DIMMs. DO NOT
install DDR or DDR2 DIMMs to the DDR3 DIMM sockets.
Removing a DIMM
To remove a DIMM:
1.
Support the DIMM lightly with
your fingers when pressing the
retaining clips. The DIMM might
get damaged when it flips out
with extra force.
2.
2-18
2
Simultaneously press the retaining
clips outward to unlock the DIMM.
DDR3 DIMM notch
1
1
Remove the DIMM from the socket.
Chapter 2: Hardware information
2.5
Expansion slots
In the future, you may need to install expansion cards. The following sub‑sections
describe the slots and the expansion cards that they support.
Ensure to unplug the power cord before adding or removing expansion cards.
Failure to do so may cause you physical injury and damage motherboard
components.
2.5.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that came with
it and make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already installed in a
chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep the screw
for later use.
4.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
2.5.2
Configuring an expansion card
After installing the expansion card, configure the it by adjusting the software
settings.
1.
Turn on the system and change the necessary BIOS settings, if any. See
Chapter 4 for information on BIOS setup.
2.
Assign an IRQ to the card. Refer to the tables on the next page.
3.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will
arise between the two PCI groups, making the system unstable and the card
inoperable.
ASUS Z8NH-D12 Series
2-19
2.5.3
Interrupt assignments
Standard Interrupt assignments
IRQ
Priority
Standard function
0
1
System Timer
1
2
Keyboard Controller
2
-
Programmable Interrupt
4*
12
Communications Port (COM1)
5*
13
--
6
14
Floppy Disk Controller
7*
15
--
8
3
System CMOS/Real Time Clock
9*
4
ACPI Mode when used
10*
5
IRQ Holder for PCI Steering
11*
6
IRQ Holder for PCI Steering
12*
7
PS/2 Compatible Mouse Port
13
8
Numeric Data Processor
14*
9
Primary IDE Channel
15*
10
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-20
Chapter 2: Hardware information
2.5.4
PCI Express x16 slot (x16 link)
The onboard PCI Express x16 slot provides x16 link to Intel 5500 I/O Hubchipset.
This slot supports VGA cards and various server class high performance add-on
cards. It also supports a special riser card with two PCI Express x16 (x8 link) slots
for 1U server system.
PCIEx16 slot (x16 link)
The picture abvoe is for reference only. The motherboard layout may vary with
models.
2.5.5
Installing ASMB4 management board
Follow the steps below to install an optional ASMB4 management board on your
motherboard.
1.
Locate the BMC_FW1 header on
the motherboard.
2.
Orient and press the ASMB4
management card in place.
ASUS Z8NH-D12 Series
2-21
2.6
1.
Jumpers
Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters
by erasing the CMOS RTC RAM data. The onboard button cell battery
powers the RAM data in CMOS, which include system setup information such
as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Move the jumper cap from pins 1–2 (default) to pins 2–3. Keep the cap
on pins 2–3 for about 5–10 seconds, then move the cap back to pins 1–2.
3. Plug the power cord and turn ON the computer.
4. Hold down the <Del> key during the boot process and enter BIOS setup
to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper
default position. Removing the cap will cause system boot failure!
If the steps above do not help, remove the onboard battery and move the
jumper again to clear the CMOS RTC RAM data. After the CMOS clearance,
reinstall the battery.
2-22
Chapter 2: Hardware information
2.
VGA controller setting (3-pin VGA_SW1)
This jumper allows you to enable or disable the onboard VGA controller. Set
to pins 1–2 to activate the VGA feature.
ASUS Z8NH-D12 Series
2-23
3.
DDR3 voltage control setting (4-pin LVDDR3_SEL1; LVDDR3_SEL2)
These jumpers allow you to adjust the DIMM voltage. Set to pins 1–2 to
select 1.5V BIOS control, pins 2–3 to select 1.2V Force or 3–4 to select
1.35V Force.
2-24
Chapter 2: Hardware information
4.
LAN controller setting (3-pin LAN_SW1, LAN_SW2)
These jumpers allow you to enable or disable the onboard Intel® Intel
82574LGigabit LAN controllers. Set to pins 1–2 to activate the Gigabit LAN
feature.
ASUS Z8NH-D12 Series
2-25
5.
Intel® ICH10R SATA port S/W RAID setting (3-pin RAID_SEL1)
This jumper allows you to select the Serial ATA RAID configuration utility to
use when you create disk arrays. Place the jumper caps on pins 1–2 if you
want to use the LSI Logic Embedded SATA RAID Setup Utility (default);
otherwise, place the jumper caps on pins 2–3 to use the Intel® Matrix Storage
Manager (IMSM).
2-26
Chapter 2: Hardware information
6.
Force BIOS recovery setting (3-pin RECOVERY1)
This jumper allows you to quickly update or recover the BIOS settings when it
becomes corrupted.
To update the BIOS:
1. Prepare a USB flash disk that contains the original or latest BIOS for the
motherboard (XXXXXX.ROM) and the AFUDOS.EXE utility.
2. Set the jumper to pins 2–3.
3. Insert the USB flash and turn on the system to update the BIOS.
4. Shut down the system.
5. Set the jumper back to pins 1–2.
6. Turn on the system.
ASUS Z8NH-D12 Series
2-27
2.7
Connectors
2.7.1
Rear panel connectors
Z8NH-D12; Z8PH-D12/IFB
Z8PH-D12 SE/QDR
9
1.
RJ-45 port for iKVM. This RJ-45 port functions only when you install ASMB4
management card.
2.
USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports
are available for connecting USB 2.0 devices.
3.
LAN 2 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
4.
LAN 1 (RJ-45) port. This port allows Gigabit connection to a Local Area
Network (LAN) through a network hub. Refer to the table below for the LAN
port LED indications.
LAN port LED indications
2-28
Activity/Link LED
Status
Description
Speed LED
Status
Description
OFF
No link
OFF
10 Mbps connection
GREEN
Linked
ORANGE
100 Mbps connection
BLINKING
Data activity
GREEN
1 Gbps connection
ACT/LINK SPEED
LED
LED
LAN port
Chapter 2: Hardware information
5.
Serial (COM1) port. This 9-pin communication port is for pointing devices or
other serial devices.
6.
Video Graphics Adapter port. This port is for a VGA monitor or other VGAcompatible devices.
7.
Location LED. This LED lights up for you to conveniently locate the system
in error.
8.
InfiniBand (IFX1). (Z8PH-D12/IFB only) This port allows connection with a
CX4 cable to an InfiniBand switch.
9.
InfiniBand (MQSFP1). (Z8PH-D12 SE/QDR only) This port allows
connection with a QSFP cable to an InfiniBand switch.
10. InfiniBand (MQSFP1) indicators. (Z8PH-D12 SE/QDR only) These
indicators show the status of InfiniBand (MQSFP1).
Infiniband (MQSFP1) indications
Activity LED Link LED
Description
Off
Off
No device
Orange
Green
Device plugged in; Ready
Orange
Blinking
Green
Device plugged in; Data transmitting
ASUS Z8NH-D12 Series
ACT LED
LINK LED
2-29
2.7.2
1.
Internal connectors
Serial ATA connectors (7-pin SATA1, SATA2, SATA3, SATA4)
Supported by the Intel® ICH10R chipset, these connectors are for the Serial
ATA signal cables for Serial ATA hard disk drives that allows up to 3Gb/s of
data transfer rate.
If you installed Serial ATA hard disk drives, you can create a RAID 0, RAID 1,
RAID 10, or RAID 5 configuration.
The actual data transfer rate depends on the speed of Serial ATA hard disks
installed.
2-30
Chapter 2: Hardware information
2.
USB connector (5-1 pin USB3; A-Type USB4)
These connectors are for USB 2.0 ports. Connect the USB module cables
to connectors USB3, then install the modules to a slot opening at the
back of the system chassis. These USB connectors comply with USB 2.0
specification that supports up to 480 Mbps connection speed.
3.
Thermal sensor cable connectors (3-pin TR1, TR2)
These connectors are for temperature monitoring. Connect the thermal
sensor cables to these connectors and place the other ends to the devices,
which you want to monitor temperature.
ASUS Z8NH-D12 Series
2-31
4.
Front fan connectors
(4-pin FRNT_FAN1, FRNT_FAN2, FRNT_FAN3, FRNT_FAN4)
The fan connectors support cooling fans of 350 mA–740 mA (8.88 W max.)
or a total of 3.15 A–6.66 A (53.28 W max.) at +12V. Connect the fan cables to
the fan connectors on the motherboard, ensuring that the black wire of each
cable matches the ground pin of the connector.
2-32
•
DO NOT forget to connect the fan cables to the fan connectors. Insufficient
air flow inside the system may damage the motherboard components.
•
These are not jumpers! DO NOT place jumper caps on the fan connectors!
•
All fans feature the ASUS Smart Fan technology.
Chapter 2: Hardware information
5.
6.
LPC debug card connector (14-1 pin LPC1)
This is a low pin count interface used to plug in the LPC debug card.
Serial General Purpose Input/Output connector (6-1 pin SGPIO1)
This connector is used for the SGPIO peripherals for the LSI MegaRAID and
Intel Matrix RAID SATA LED.
ASUS Z8NH-D12 Series
2-33
7.
8.
BMC header (BMC_FW1)
The BMC connector on the motherboard supports an ASUS® Server
Management Board 4 Series (ASMB4).
Power Supply SMBus connectors (6-1 pin JP1; JP2)
These connectors allow you to connect SMBus (System Management Bus) to
the power supply unit to read PSU information. Devices communicate with an
SMBus host and/or other SMBus devices using the SMBus interface.
2-34
Chapter 2: Hardware information
9.
Proprietary power connectors
(20-pin PWR1, 20-pin PWR2, 4-pin PWR3)
These connectors are for Proprietary power supply plugs. The power supply
plugs are designed to fit these connectors in only one orientation. Orient the
connectors and push down firmly until they completely fit.
The 4-pin EZ_PLUG is designed for hard disk drives power supply. DO NOT
connect other 4-pin power connectors of the power supply unit (PSU) to this
connector.
•
Connect either one of the 20-pin power connectors to boot up the system.
•
Use of a PSU with a higher power output is recommended when
configuring a system with more power-consuming devices. The system
may become unstable or may not boot up if the power is inadequate.
•
USE THE PROPRIETARY POWER SUPPLY ONLY; otherwise you may
damage the motherboard. Ensure that your PSU can provide at least the
minimum power required by your system.
ASUS Z8NH-D12 Series
2-35
10. System panel connector (20-pin PANEL1)
This connector supports several chassis-mounted functions.
1. System power LED (3-pin PLED)
This 3-pin connector is for the system power LED. Connect the chassis
power LED cable to this connector. The system power LED lights up
when you turn on the system power, and blinks when the system is in
sleep mode.
2. Message LED (2-pin MLED)
This 2-pin connector is for the message LED cable that connects to
the front message LED. The message LED is controlled by Hardware
monitor to indicate an abnormal event occurance.
3. System warning speaker (4-pin SPEAKER)
This 4-pin connector is for the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
4. Hard disk drive activity LED (2-pin HDDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
5. Proprietary power button/soft-off button (2-pin PWRSW)
This connector is for the system power button. Pressing the power
button turns the system on or puts the system in sleep or soft-off mode
depending on the BIOS settings. Pressing the power switch for more
than four seconds while the system is ON turns the system OFF.
6. Reset button (2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
2-36
Chapter 2: Hardware information
11. Auxiliary panel connector (20-pin AUX_PANEL1)
This connector is for additional front panel features including front panel
SMB, locator LED and switch, chassis intrusion, and LAN LEDs.
1. Front panel SMB (6-1 pin FPSMB)
These leads connect the front panel SMBus cable.
2. LAN activity LED (2-pin LAN1_LED, LAN2_LED)
These leads are for Gigabit LAN activity LEDs on the front panel.
3. Chassis intrusion (4-1 pin CHASSIS)
These leads are for the intrusion detection feature for chassis with
intrusion sensor or microswitch. When you remove any chassis
component, the sensor triggers and sends a high-level signal to these
leads to record a chassis intrusion event. The default setting is short
CASEOPEN and GND pin by jumper cap to disable the function.
4. Locator LED (2-pin LOCATORLED1 and 2-pin LOCATORLED2)
These leads are for the locator LED1 and LED2 on the front panel.
Connect the Locator LED cables to these 2-pin connector. The LEDs will
light up when the Locator button is pressed.
5. Locator Button/Swich (2-pin LOCATORBTN)
These leads are for the locator button on the front panel. This button
queries the state of the system locator.
ASUS Z8NH-D12 Series
2-37
2-38
Chapter 2: Hardware information
This chapter describes the power up
sequence, and ways of shutting down the
system.
3
Powering up
Chapter summary
3.1
3.2
3
Starting up for the first time......................................................... 3-3
Turning off the computer.............................................................. 3-4
ASUS Z8NH-D12 Series
3.1
Starting up for the first time
1.
After making all the connections, replace the system case cover.
2.
Ensure that all switches are off.
3.
Connect the power cord to the power connector at the back of the system
chassis.
4.
Connect the power cord to a power outlet that is equipped with a surge
protector.
5.
Turn on the devices in the following order:
a. Monitor
b. External SCSI devices (starting with the last device on the chain)
c. System power
6.
After applying power, the system power LED on the system front panel case
lights up. For systems with Proprietary power supplies, the system LED lights
up when you press the Proprietary power button. If your monitor complies
with “green” standards or if it has a “power standby” feature, the monitor LED
may light up or switch between orange and green after the system LED turns
on.
The system then runs the power-on self-test or POST. While the tests are
running, the BIOS beeps or additional messages appear on the screen. If you
do not see anything within 30 seconds from the time you turned on the power,
the system may have failed a power-on test. Check the jumper settings and
connections or call your retailer for assistance.
7.
At power on, hold down the <Del> key to enter the BIOS Setup. Follow the
instructions in Chapter 4.
ASUS Z8NH-D12 Series
3-3
3.2
Powering off the computer
3.2.1
Using the OS shut down function
If you are using Windows® 2000/2003 Server:
1. Click Start then click Shut Down.
2. Select Shut Down from the What do you want the computer to do? list
box.
3.
Select Shutdown Event Tracker.
4.
Ensure that the Planned check box is checked.
5.
Select shutdown from the list box.
6.
If necessary, key in comments.
7.
Click OK.
3.2.2
Using the dual function power switch
While the system is ON, pressing the power switch for less than four seconds puts
the system to sleep mode or to soft-off mode, depending on the BIOS setting.
Pressing the power switch for more than four seconds lets the system enter the
soft-off mode regardless of the BIOS setting. Refer to section 4.5 Power Menu in
Chapter 4 for details.
3-4
Chapter 3: Powering up
This chapter tells how to change the
system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS
parameters are also provided.
4
BIOS setup
Chapter summary
4
4.1
Managing and updating your BIOS............................................. 4-3
4.3
Main menu................................................................................... 4-10
4.2
4.4
4.5
4.6
4.7
BIOS setup program..................................................................... 4-7
Advanced menu.......................................................................... 4-16
Server menu................................................................................ 4-33
Boot menu................................................................................... 4-35
Exit menu..................................................................................... 4-39
ASUS Z8NH-D12 Series
4.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic
Input/Output System (BIOS) setup:
1.
AFUDOS utility (Updates the BIOS in DOS mode using a bootable USB
flash disk drive.)
2.
ASUS CrashFree BIOS 3 (To recover the BIOS using a bootable USB flash
disk drive when the BIOS file fails or gets corrupted.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable USB flash
disk drive in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or AFUDOS utilities.
4.1.1
AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment using
a bootable USB flash disk drive with the updated BIOS file. This utility also allows
you to copy the current BIOS file that you can use as backup when the BIOS fails
or gets corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
The succeeding BIOS screens are for reference only. The actual BIOS screen
displays may not be the same as shown.
1.
Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable USB flash disk drive you created earlier.
2.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than eight
alphanumeric characters for the main filename and three alphanumeric
characters for the extension name.
A:\>afudos /oOLDBIOS1.rom
Main filename
ASUS Z8NH-D12 Series
Extension name
4-3
3.
Press <Enter>. The utility copies the current BIOS file to the USB flash disk
drive.
A:\>afudos /oOLDBIOS1.rom
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
Write to file...... ok
A:\>
The utility returns to the DOS prompt after copying the current BIOS file.
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
Visit the ASUS website at www.asus.com and download the latest BIOS file
for the motherboard. Save the BIOS file to a bootable����������������������
USB flash disk drive�.
Write the BIOS filename on a piece of paper. You need to type the exact BIOS
filename at the DOS prompt.
2.
Copy the AFUDOS utility (afudos.exe) from the motherboard support CD to
the bootable������������������������������������������
USB flash disk drive ��������������������
you created earlier.
3.
Boot the system in DOS mode, then at the prompt, type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable�����
USB
flash disk drive���������������������
, then press <Enter>.
A:\>afudos /i8036A0.ROM
The utility verifies the file, then starts updating the BIOS file.
A:\>afudos /i8036A0.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... 0x0008CC00 (9%)
DO NOT shut down or reset the system while updating the BIOS to prevent
system boot failure!
4-4
Chapter 4: BIOS setup
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /i8036A0.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ....... done
Reading flash ...... done
Advance Check ......
Erasing flash ...... done
Writing flash ...... done
Verifying flash .... done
Please restart your computer
A:\>
ASUS Z8NH-D12 Series
4-5
4.1.2
ASUS CrashFree BIOS 3 utility
The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore
the BIOS file when it fails or gets corrupted during the updating process. You can
update a corrupted BIOS file using a USB flash drive that contains the updated
BIOS file.
Prepare a USB flash drive containing the updated motherboard BIOS before
using this utility.
Recovering the BIOS from a USB flash drive
To recover the BIOS from a USB flash drive:
1.
Remove any floppy disk from the floppy disk drive and turn the system on.
2.
Insert the USB flash drive with the original or updated BIOS file to one USB
port on the system.
3.
The utility will automatically recover the BIOS. It resets the system when the
BIOS recovery finished.
DO NOT shut down or reset the system while recovering the BIOS! Doing so
would cause system boot failure!
The recovered BIOS may not be the latest BIOS version for this motherboard.
Visit the ASUS website at www.asus.com to download the latest BIOS file.
4-6
Chapter 4: BIOS setup
4.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can update
using the provided utility described in section 4.1 Managing and updating your
BIOS.
Use the BIOS Setup program when you are installing a motherboard, reconfiguring
your system, or prompted to “Run Setup.” This section explains how to configure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
configuration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to reconfigure your system using the BIOS Setup program so that the
computer can recognize these changes and record them in the CMOS RAM of the
firmware chip.
The firmware chip on the motherboard stores the Setup utility. When you start up
the computer, the system provides you with the opportunity to run this program.
Press <Del> during the Power-On Self-Test (POST) to enter the Setup utility;
otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make
your selections from the available options using the navigation keys.
•
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Select the Load Setup Defaults item under the
Exit Menu. See section 4.8 Exit Menu.
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
•
Visit the ASUS website at www.asus.com to download the latest BIOS file
for this motherboard.
ASUS Z8NH-D12 Series
4-7
4.2.1
BIOS menu screen
Menu items
Main
Menu bar
Advanced
Configuration fields
Server
System Time
System Date
SATA
SATA
SATA
SATA
1
2
3
4
:
:
:
:
General help
BIOS SETUP UTILITY
Boot
Exit
[17:44:30]
[Mon, 03/08/2010]
[ST3160812AS]
[Not Detected]
[Not Detected]
[Not Detected]
IDE Configuration
AHCI Configuration
System Information
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system Date.
←→
↑↓
+Tab
F1
F10
ESC
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Sub-menu items
4.2.2
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
Advanced
Server
Boot
Exit
For changing the basic system configuration
For changing the advanced system settings
For changing the advanced server settings
For changing the system boot configuration
For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard
until the desired item is highlighted.
4.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for that
particular menu. Use the navigation keys to select items in the menu and change
the settings.
Some of the navigation keys differ from one screen to another.
4-8
Chapter 4: BIOS setup
4.2.4
Menu items
The highlighted item on the
menu bar displays the specific
items for that menu. For
example, selecting Main shows
the Main menu items.
System Time
System Date
SATA1
SATA2
SATA3
SATA4
Use [ENTER], [TAB]
select a field.
or [SHIFT-TAB] to
Use [+] or [-] to
configure system
Date.
IDE Configuration
AHCI Configuration
System Information
The other items (Advanced,
Power, Boot, and Exit) on the
menu bar have their respective
menu items.
4.2.5
[15:17:09]
[Mon 08/08/2010]
[Not Detected]
[Not Detected]
[Not Detected]]
[Not Detected]
Main menu items
Sub-menu items
A solid triangle before each item on any menu screen means that the item has a
sub-menu. To display the sub-menu, select the item and press <Enter>.
4.2.6
Configuration fields
These fields show the values for the menu items. If an item is user-configurable,
you can change the value of the field opposite the item. You cannot select an item
that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To
change the value of a field, select it then press <Enter> to display a list of options.
Refer to 4.2.7 Pop-up window.
4.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the
configuration options for that item.
4.2.8
Scroll bar
A scroll bar appears on the right side of a
menu screen when there are items that do
not fit on the screen. Press the Up/Down
arrow keys or <Page Up> /<Page Down>
keys to display the other items on the
screen.
4.2.9
General help
Pop-up window
Scroll bar
At the top right corner of the menu screen is a brief description of the selected
item.
ASUS Z8NH-D12 Series
4-9
4.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving
you an overview of the basic system information.
Refer to section 4.2.1 BIOS menu screen for information on the menu screen
items and how to navigate through them.
Main
Advanced
Server
System Time
System Date
SATA
SATA
SATA
SATA
1
2
3
4
:
:
:
:
BIOS SETUP UTILITY
Boot
Exit
[17:44:30]
[Mon, 03/08/2010]
[ST3160812AS]
[Not Detected]
[Not Detected]
[Not Detected]
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system Date.
←→
↑↓
+Tab
F1
F10
ESC
IDE Configuration
AHCI Configuration
System Information
Select Screen
Select Item
Change Field
Select Field
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
4.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
4.3.3
SATA1—4
The items in this menu allow you to set or change the configurations for the SATA
devices installed in the system. Select an item then press <Enter> if you wish to
configure the item.
BIOS SETUP UTILITY
Main
SATA 1
Device
:Hard Disk
Vendor
:xxxxxxxxx
Size
:xx.xGB
LBA Mode :Supported
Block Mode:16Sectors
PIO Mode :4
Async DMA :MultiWord DMA-2
Ultra DMA :Ultra DMA-6
S.M.A.R.T.:Supported
Type [Auto]
LBA/Large Mode [Auto]
Block(Multi-Sector Transfer)M
[Auto]
PIO Mode [Auto]
DMA Mode [Auto]
SMART Monitoring [Auto]
32Bit Data Transfer [Enabled]
Disabled: Disabled LBA
Mode.
Auto: Enables LBA
Mode if the device
supports it and the
device is not already
formatted with LBA
Mode disabled.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4-10
Chapter 4: BIOS setup
The BIOS automatically detects the values opposite the dimmed items (Device,
Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and
S.M.A.R.T. monitoring). These values are not user-configurable. These items show
N/A if no IDE device is installed in the system.
Type [Auto]
Allows you to select the type of device connected to the system.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to [Auto] enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Auto]
Block (Multi-Sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to [Auto], the data
transfer from and to the device occurs multiple sectors at a time if the device
supports multi-sector transfer feature. When set to [Disabled], the data transfer
from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
PIO Mode [Auto]
Allows you to select the data transfer mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Sets the DMA mode.
Configuration options: [Auto] [SWDMA0] [SWDMA1] [SWDMA2] [MWDMA0]
[MWDMA1] [MWDMA2] [UDMA0] [UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-11
4.3.4
IDE Configuration
The items in this menu allow you to set or change the configurations for the
IDE/SATA devices installed in the system. Select an item then press <Enter> if you
wish to configure the item.
BIOS SETUP UTILITY
Main
IDE Configuration
Options
SATA Configuration
Configure SATA as
[Enhanced]
[IDE]
Hard Disk Write Protect
IDE Detect Time Out (Sec)
[Disabled]
[35]
Disabled
Compatible
Enhanced
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
SATA Configuration [Enhanced]
Configuration options: [Disabled] [Compatible] [Enhanced]
Configure SATA as [IDE]
Sets the configuration for the Serial ATA connectors supported by the
Southbridge chip. Configuration options: [IDE] [RAID] [AHCI]
•
If you want to use the Serial ATA hard disk drives as Parallel ATA physical
storage devices, keep the default setting [IDE].
•
If you want the Serial ATA hard disk drives to use the Advanced Host
Controller Interface (AHCI), set this item to [AHCI]. The AHCI allows
the onboard storage driver to enable advanced Serial ATA features that
increases storage performance on random workloads by allowing the drive
to internally optimize the order of commands.
•
If you want to create a LSI MegaRAID, or the Intel® Matrix Storage
Technology configuration from the Serial ATA hard disk drives, set this item
to [RAID].
Hard Disk Write Protect [Disabled]
Disables or enables device write protection. This will be effective only if the device
is accessed through BIOS. Configuration option: [Disabled] [Enabled]
IDE Detect Time Out (Sec) [35]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
4-12
Chapter 4: BIOS setup
4.3.5
AHCI Configuration
This menu is the section for AHCI configuration.
BIOS SETUP UTILITY
Main
AHCI Settings
AHCI CD/DVD Boot Time out
SATA
SATA
SATA
SATA
Port1
Port2
Port3
Port4
[Not
[Not
[Not
[Not
[35]
Some SATA CD/DVD in
AHCI mode need to
wait ready longer.
Detected]
Detected]
Detected]
Detected]
AHCI CD/DVD Boot Time out [35]
Selects the boot time out value for SATA CD/DVD devices in AHCI mode.
Congifuration options: [0] [5] [10] [15] [20] [25] [30] [35]
SATA Port1–4 [XXXX]
Displays the status of auto-detection of SATA devices.
BIOS SETUP UTILITY
Main
SATA Port1
Device
Select the type
of device connected
to the system.
:Not Detected
SATA Port1
SMART Monitoring
[Auto]
[Enabled]
SATA Port1 [Auto]
Allows you to select the type of device connected to the system.
Configuration options: [Auto] [Not Installed]
SMART Monitoring [Enabled]
Allows you to set the Self-Monitoring, Analysis and Reporting Technology.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-13
4.3.6
System Information
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
BIOS SETUP UTILITY
Main
AMIBIOS
Version
Build Date
:0201
:02/25/10
Processor
Speed
Count
:2266MHZ
:1
System Memory
Usable Size
: 2040MB
Onboard LAN1 Address
Onboard LAN2 Address
:
:
00.E0.18.01.10.00
00.E0.18.01.10.01
System Memory Information
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
AMIBIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
System Memory Information
Displays system memory information.
Main
BIOS SETUP UTILITY
System Memory Information
CPU1 Memory Information
CPU2 Memory Information
CPU1/2 Memory Configuration
Allows you to check information of installed memory (6 DIMMs per CPU).
4-14
Chapter 4: BIOS setup
CPU1/2 Memory Configuration
Displays the auto-detected memory specification.
BIOS SETUP UTILITY
Main
CPU1 Memory Configuration
Speed
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
DIMM_C1
DIMM_C2
DDR3 1067
N/A
N/A
N/A
N/A
N/A
N/A
ASUS Z8NH-D12 Series
4-15
4.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
Main
Advanced
Server
BIOS SETUP UTILITY
Boot
Exit
Configure CPU.
CPU Configuration
Chipset Configuration
Legacy Device Configuration
USB Configuration
PCIPnP Configuration
Power On Configuration
Event Log Configuration
Hardware Monitor
I/O Virtualization
PCI Exppress Configuration
ACPI Configuration
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4.4.1
CPU Configuration
The items in this menu show the CPU-related information that the BIOS
automatically detects. Some items may not appear if your CPU does not support
the related functions.
Advanced
BIOS SETUP UTILITY
Configure advanced CPU settings
Module Version:01.08
Manufacturer:Intel
Brand String:Intel(R) Xeon(R) CPU L5640 @ 2.27GHz
Frequency
:2.26GHz
BCLK Speed :133MHz
Cache L1
:384 KB
Cache L2
:1536 KB
Cache L3
:12288 KB
Ratio Status:Unlocked (Min:12, Max:17)
Ratio Actual Value :17
Sets the ratio between
CPU Core Clock and the
FSB Frequency.
Note:If an invalid
ratio is set in CMOS
then actual and
setpoint values may
differ.
Ratio CMOS Setting:
C1E Support
Hardware Prefetcher
Adjacent Cache Line Prefetch
MPS and ACPI MADT ordering
Max CPUID Value Limit
Intel(R) Virtualization Tech
←→
↑↓
+F1
F10
ESC
[17]
[Enabled]
[Enabled]
[Enabled]
[Modern ordering]
[Disabled]
[Enabled]
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4-16
Chapter 4: BIOS setup
Scroll down for more items.
Advanced
BIOS SETUP UTILITY
CPU TM Function
Execute-Disable Bit Capability
Intel(R) HT Technology
Active Processor Cores
A20M
Intel(R) SpeedStep(TM) Tech
Intel(R) TurboMode tech
Intel(R) C-STATE Tech
C3 State
C6 State
C State package limit setting
C1 Auto Demotion
C3 Auto Demotion
ACPI T State
[Enabled]
[Enabled]
[Enabled]
[All]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[ACPI C3]
[Enabled]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Sets the ratio between
CPU Core Clock and the
FSB Frequency.
Note:If an invalid
ratio is set in CMOS
then actual and
setpoint values may
differ.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Ratio CMOS Setting [17]
Allows you to adjust the ratio between CPU Core Clock and BCLK Frequency.
Use the <+> and <-> keys to adjust the value.
Configuration options: [12.0] [13.0] [14.0] [15.0] [16.0] [17.0]]
C1E Support [Enabled]
Allows you to enable or disable Enhanced Halt State support.
Configuration options: [Disabled] [Enabled]
Hardware Prefetcher [Enabled]
Allows you to enable or disable the Hardware Prefetcher function.
Configuration options: [Disabled] [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Allows you to enable or disable the Adjacent Cache Line Prefetch function.
Configuration options: [Disabled] [Enabled]
MPS and ACPI MADT ordering [Modern ordering]
Allows you to select the ordering according to the operating system you install.
Select [Modern ordering] for Windows XP or later OS versions and [Legacy
ordering] for Windows 2000 or earlier OS version.
Configuration options: [Modern ordering] [Legacy ordering]
Max CPUID Value Limit [Disabled]
Setting this item to [Enabled] allows legacy operating systems to boot even without
support for CPUs with extended CPUID functions.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-17
Intel(R) Virtualization Tech [Enabled]
The Intel® Virtualization Technology allows a hardware platform to run multiple
operating systems separately and simultaneously, enabling one system to virtually
function as several systems. Configuration options: [Disabled] [Enabled]
CPU TM Function [Enabled]
This function enables the overheated CPU to throttle the clock speed to cool down.
Configuration options: [Disabled] [Enabled]
Execute-Disable Bit Capability [Enabled]
Allows you to enable or disable the No-Execution Page Protection Technology.
Setting this item to [Disabled] forces the XD feature flag to always return to zero (0).
Configuration options: [Disabled] [Enabled]
Intel(R) HT Technology [Enabled]
Allows you to enable or disable the Intel Hyper-Threading Technology function.
When disabled, only one thread per activated core is enabled.
Configuration options: [Enabled] [Disabled]
Active Processor Cores [All]
Allows you to choose the number of CPU cores to activate in each processor
package.Configuration options: [All] [1] [2]
A20M [Disabled]
Legacy OSes and APs may need A20M enabled.
Configuration options: [Disabled] [Enabled]
Intel(R) SpeedStep (TM) Tech [Enabled]
When set to [Disabled], the CPU runs at its default speed. When set to [Enabled],
the CPU speed is controlled by the operating system.
Configuration options: [Disabled] [Enabled]
Intel(R) TurboMode tech [Enabled]
The turbo mode allows the processor cores to run faster than the marked
frequency in specific condition. Configuration options: [Disabled] [Enabled]
Intel(R) C-STATE Tech [Enabled]
The Intel® C-State Technology allows the CPU to save more power under idle
mode. Enable this item only when you install a C-State Technology-supported
CPU. Configuration options: [Disabled] [Enabled]
The following items appear only when you set the Intel(R) C-STATE Tech
item to [Enabled].
4-18
Chapter 4: BIOS setup
C3 State [ACPI C3]
Allows you to select Nehalem C state action.
Configuratiton options: [Disabled] [ACPI C2] [ACPI C3]
C6 State [Enabled]
Allows you to select Nehalem C state action.
Configuratiton options: [Disabled] [Enabled]
C State package limit setting [Auto]
We recommend that you set this item to [Auto] for BIOS to automatically detect the
C-State mode supported by your CPU.
Configuration options: [Auto] [C1] [C3] [C6]
C3 Auto Demotion [Enabled]
When this item is enabled, the CPU will conditionally demote C6 requests to C3
based on the uncore auto-demote information.
Configuration options: [Disabled] [Enabled]
ACPI T State [Disabled]
Enables or disables processor throttling report in ACPI.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-19
4.4.2
Chipset Configuration
The Chipset configuration menu allows you to change advanced chipset settings.
Select an item then press <Enter> to display the sub-menu.
Advanced
BIOS SETUP UTILITY
Advanced Chipset Settings
Configure CPU Bridge
features.
WARNING: Setting wrong values in below sections
may cause system to malfunction.
CPU Bridge Configuration
North Bridge Configuration
South Bridge Configuration
Intel VT-d Configuration
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
CPU Bridge Configuration
Advanced
BIOS SETUP UTILITY
CPU Bridge Chipset Configuration
CPU Revision
REVISION
Current CSI Frequency
Current Memory Frequency
:B0
:6.400GT
:5.866GT
:1066 Mhz
CSI Links Speed
CSI Frequency
CSI Isochronous
Memory
CSI
L1
Frequency
Memory
CSI
Power
Mode
Optimization Policy
Demand Scrubbing
Patrol Frequency
Memory
Scrubbing
Throttling
Memory
Mode
- Closed Loop
Throttling
Memory
ECC Function
- Open Loop
Double Rate Refresh
Demand Scrubbing
Patrol Scrubbing
NUMA Aware
Page Policy
v02.61 (C)Copyright
To transition the CSI
links to full-speed
or leave them in
slow-mode.
[Full-Speed]
[Auto]
[Disabled]
[Auto]
[Enabled]
[Static]
[Independent]
[Disabled]
[Disabled]
[Auto]
[Disabled]
[Independent]
←→ Select Screen
[Disabled]
[Enabled]
↑↓
Select Item
[Auto]
+Change Option
[Enabled]
F1
General Help
[Disabled]
F10 Save and Exit
[Auto]
ESC Exit
[Open]
1985-2008, American Megatrends, Inc.
1985-2009,
Scroll down for more items.
Adaptive Page
Data Scramble
Split Below 4GB
Channel Interleaving
Rank Interleaving
Memory Thermal Throttling
Force VDD 1.5V
[Disabled]
[Enabled]
[Disabled]
[6:1]
[4:1]
[Disabled]
[Disabled]
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4-20
Chapter 4: BIOS setup
CSI Links Speed [Full-Speed]
Allows you to set the speed of CSI Links.
Configuration options: [Slow-Mode] [Full-Speed]
CSI Frequency [Auto]
Allows you to set the CSI frequency.
Configuration options: [Auto] [4.800GT] [5.866GT] [6.400GT]
CSI Isochronous [Disabled]
Configuration options: [Disabled] [Enabled]
CSI L1 [Disabled]
Configuration options: [Disabled] [Enabled]
CSI Power Optimization Policy [Static]
Configuration options: [Adaptive] [Static] [Bypass]
Memory Frequency [Auto]
You may allow the system to detect DDR3 memory frequency via SPD or designate
a specific frequency.
Configuration options: [Auto] [Force DDR-800] [Force DDR-1066]
[Force DDR-1333]
Memory Mode [Independent]
Allows you to set Memory channel mode.
Configuration options: [Independent] [Channel Mirroring] [Lockstep]
Memory ECC Function [Enabled]
Allows you to enable or disable Memory ECC fucntion.
Configuration options: [Disabled] [Enabled]
Double Rate Refresh [Auto]
Configuration options: [Disabled] [Auto]
Demand Scrubbing [Enabled]
Enables or disables the ECC demand scrub.
Configuration options: [Disabled] [Enabled]
Patrol Scrubbing [Disabled]
Enables or disables the ECC patrol scrub.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-21
NUMA Aware [Auto]
Configuration options: [Disabled] [Enabled]
Page Poilcy [Open]
Configuration options: [Closed] [Open]
Adaptive Page [Disabled]
Configuration options: [Disabled] [Enabled]
Data Scramble [Enabled]
Configuration options: [Disabled] [Enabled]
Split Below 4 GB [Disabled]
Configuation options: [Disabled] [Auto]
Channel Interleaving [6:1]
Allows you to set the channel interleaving setting.
Configuation options: [1:1] [2:1] [4:1] [6:1]
Rank Interleaving [4:1]
Allows you to set the rank interleaving setting.
Configuation options: [1:1] [2:1] [4:1]
Memory Thermal Throttling [Disabled]
[CLTT] is for closed loop thermal throttling and [OLTT] for open loop thermal
throttling. Configuration options: [CLTT] [OLTT] [Disabled] [Auto]
Force VDD 1.5V [Disabled]
Configuration options: [Disabled] [Enabled]
4-22
Chapter 4: BIOS setup
North Bridge Configuration
The North Bridge Configuration menu shows the auto-detected Northbridge values.
Advanced
BIOS SETUP UTILITY
NorthBridge Chipset Configuration
NB Revision
Current CSI Frequency
:C2
:5.866GT
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
V02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
South Bridge Configuration
Advanced
BIOS SETUP UTILITY
CPU Bridge Chipset Configuration
USB Functions
USB Port Configure
USB 2.0 Controller
[Enabled]
[8+4 USB Ports]
[Enabled]
SLP_S4# Min. Assertion Width
[1 to 2 seconds]
Options
Disabled
Enabled
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
USB Functions [Enabled]
Allows you to configure the amount of USB ports to be enabled.
Configuration options: [Disabled] [2 USB Ports] [3 USB Ports] [4 USB Ports]
USB Port Configure [8+4 USB Ports]
This item disappears when you set the USB Functions item to [Disabled].
Configuration options: [6+6 USB Ports] [8+4 USB Ports]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
ASUS Z8NH-D12 Series
4-23
SLP_S4# Min. Assertion Width [1 to 2 seconds]
Configuration options: [4 to 5 seconds] [3 to 4 seconds] [2 to 3 seconds]
[1 to 2 seconds]
Intel VT-d Configuration
Advanced
Inel VT-d
BIOS SETUP UTILITY
Options
[Disabled]
Disabled
Enabled
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Configuration options: [Disabled] [Enabled]
4.4.3
Legacy Device Configuration
Advanced
BIOS SETUP UTILITY
Legacy Device Configuration
Serial Port1 Address
Serial Port2 Address
[3F8/IRQ4]
[2F8/IRQ3]
Allows BIOS to Enable
or Disable Floppy
Controller.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]
Serial Port2 Address [2F8/IRQ3]
Allows you to select the Serial Port2 base address.
Configuration options: [Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]
4-24
Chapter 4: BIOS setup
4.4.4
USB Configuration
Advanced
BIOS SETUP UTILITY
USB Configuration
Enables support for
legacy USB. AUTO
option disables
legacy support if
no USB devices are
connected.
Module Version - 2.24.3-13.4
USB Devices Enabled :
None
Legacy USB Support
USB 2.0 Controller Mode
BIOS EHCI Hand-Off
[Enabled]
[HiSpeed]
[Enabled]
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Legacy USB Support [Enabled]
Allows you to enable or disable support for legacy USB devices. Setting to [Auto]
allows the system to detect the presence of USB devices at startup. If detected, the
USB controller legacy mode is enabled. If no USB device is detected, the legacy
USB support is disabled. Configuration options: [Disabled] [Enabled] [Auto]
The following item appears only when you set Legacy USB Support to
[Enabled].
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller to HiSpeed (480Mbps) or FullSpeed
(12Mbps). Configuration options: [FullSpeed] [HiSpeed]
BIOS EHCI Hand-Off [Enabled]
Enables or disables the BIOS EHCI hand-off support.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-25
4.4.5
PCIPnP Configuration
The PCIPnP Configuration menu items allow you to change the advanced settings
for PCI/PnP devices.
Take caution when changing the settings of the PCI/PnP Configuration menu
items. Incorrect field values can cause the system to malfunction.
Advanced
BIOS SETUP UTILITY
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
[No]
PCI Option ROM Scan Order [Bus 0 First]
Onboard Option ROM Priority [High]
Onboard LAN1 Chip
Onboard LAN2 Chip
[Enabled]
[Enabled]
Onboard LAN1 Boot
Onboard LAN2 Boot
[PXE]
[PXE]
NO: lets the BIOS
configure all the
devices in the system.
YES: lets the
operating system
configure Plug and
Play (PnP) devices not
required for boot if
your system has a Plug
and Play operating
system.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Plug And Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set to
[Yes] and if you install a Plug and Play operating system, the operating system
configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
PCI Option ROM Scan Order [Bus 0 First]
Allows you to select the PCI option ROM scanning order. The scanning of the
option ROM will start from the lowest bus, device, fucntion number if you set this
item to [Bus 0 First]; the scanning starts from the highest bus, device, function
number if you set this item to [Bus N First].
Configuration options: [Bus 0 First] [Bus N First]
Onboard Option ROM Priority [High]
Allows you to select the onboard option ROM priority.
Configuration options: [Normal] [High]
Onboard LAN1/2 Chip [Enabled]
Allows you to enable or disable the onboard LAN1/2 chip.
Configuration: [Disabled] [Enabled]
Onboard LAN1/2 Boot [PXE]
Allows you to configure the onboard LAN1/2 boot mode.
Configuration: [Disabled] [PXE] [iSCSI]
4-26
Chapter 4: BIOS setup
4.4.6
Power On Configuration
Advanced
BIOS SETUP UTILITY
APM Configuration
Restore on AC Power Loss
Options
[Last State]
Resume On Ring [Disabled]
Resume On PME#(Wake On LAN) [Disabled]
Resume On RTC Alarm [Disabled]
Power Off
Power On
Last State
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Restore on AC Power Loss [Last State]
When set to [Power Off], the system goes into off state after an AC power loss.
When set to [Power On], the system will reboot after an AC power loss. When set
to [Last State], the system goes into either off or on state, whatever the system
state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Resume On Ring [Disabled]
When set to [Enabled], the system enables RI to generate a wake event while the
computer is in Soft-off mode. Configuration options: [Disabled] [Enabled]
Resume On PME# (Wake On LAN) [Disabled]
When set to [Enabled], the system enables PME to generate a wake event while
the computer is in Soft-off mode. Configuration options: [Disabled] [Enabled]
Resume On RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake-up event.
Configuration options: [Disabled] [Enabled]
The following items appear only when the Resume On RTC Alarm item is set
to [Enabled].
RTC Alarm Date [15]
To set the alarm date, highlight this item and press the <+> or <-> key to
make the selection.
System Time [12:30:30]
Use the <ENTER>, <TAB> or <SHIFT-TAB> key to select a field. Use the <+>
or <-> key to configure alarm time.
ASUS Z8NH-D12 Series
4-27
4.4.7
Event Log Configuration
Main Advanced
BIOS SETUP UTILITY
Event Logging details
View all unread events
on the Event Log.
View Event Log
Clear Event Log
View Event Log
Press <Enter> to read all the unread event log.
Clear Event Log
Press <Enter> to clear all events on the event log.
4.4.8
Hardware Monitor
Advanced
Hardware Monitor
CPU1 Temperature
CPU2 Temperature
TR1 Temperature
TR2 Temperature
Front Fan1 Speed
Front Fan2 Speed
Front Fan3 Speed
Front Fan4 Speed
Fan Speed Control
VCORE1 Voltage
VCORE2 Voltage
+1.5V_P1DDR3 Voltage
+1.5V_P2DDR3 Voltage
+1.5V_ICH Voltage
P1VTT Voltage
P2VTT Voltage
+1.1V_IOH Voltage
+12V Voltage
v02.61 (C)Copyright
BIOS SETUP UTILITY
CPU1 Temperature
[ 27.5ºC/ 81.5ºF]
[ 0
ºC/ 32 ºF]
[ N/A
]
[ N/A
]
[5357RPM ]
[ N/A
]
[ N/A
]
[ N/A
]
[High Density Mode]
[ 1.052 V]
[ N/A ]
[ 1.508 V]
←→ Select Screen
[ N/A ]
↑↓
Select Item
[ 1.520 V]
+Change Option
[ 1.022 V]
F1
General Help
[ 1.022 V]
F10 Save and Exit
[ 0.204 V]
ESC Exit
[12.000 V]
1985-2009, American Megatrends, Inc.
Scroll down for more items.
+5V Voltage
+3.3V Voltage
+5VSB Voltage
+3.3VSB Voltage
VBAT Voltage
[
[
[
[
[
5.196
3.246
5.132
3.198
3.126
V]
V]
V]
V]
V]
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4-28
Chapter 4: BIOS setup
CPU1/2; TR1/2 Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the CPU
temperature and the temperature of the device you would like to monitor. Select
[Ignored] if you do not wish to display the detected temperatures.
Front Fan1–4 Speed [xxxxRPM] or [Ignored] / [N/A]
The onboard hardware monitor automatically detects and displays the speed of
CPU fans, front fans, and rear fans in rotations per minute (RPM). If the fan is not
connected to the motherboard, the field shows [N/A].
Fan Speed Control [High Density Mode]
Allows you to configure the ASUS Smart Fan feature that smartly adjusts the fan
speeds for more efficient system operation.
Configuration options: [Full Speed Mode] [Whisper Mode] [Generic Mode]
[High Density Mode]
VCORE1/2 Voltage, +1.5V_P1/2DDR3 Voltage, +1.5V_ICH Voltage,
P1/2VTT Voltage, +1.1V_IOH Voltage, +12V Voltage, +5V Voltage,
+3.3V Voltage, +5VSB Voltage, +3.3VSB Voltage, VBAT Voltage
The onboard hardware monitor automatically detects the voltage output through
the onboard voltage regulators. Select [Ignored] if you do not want to detect this
item.
ASUS Z8NH-D12 Series
4-29
4.4.9
I/O Virtualization
Advanced
BIOS SETUP UTILITY
Configure I/O Virtualization Parameters
SR-IOV Supported
[Disabled]
Options
Enabled
Disabled
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
SR-IOV Supported [Disabled]
Configuration options: [Disabled] [Enabled]
4.4.10
PCI Express Configuration
Advanced
BIOS SETUP UTILITY
PCI Express Configuration
Active State Power-Management [Disabled]
Enable/Disable
PCI Express L0s and
L1 link power
states.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Active State Power-Management [Disabled]
Enables or disables the PCI Express L0s and L1 link power states.
Configuration options: [Disabled] [Enabled]
4-30
Chapter 4: BIOS setup
4.4.11
ACPI Configuration
BIOS SETUP UTILITY
Advanced
ACPI Settings
Advanced ACPI
Configuration
settings.
Advanced ACPI Configuration
Chipset ACPI Configuration
General WHEA Configuration
Use this section to
configure additional
ACPI options.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Advanced ACPI Configuration
Advanced
BIOS SETUP UTILITY
Advanced ACPI Configuration
ACPI 2.0 Support
ACPI APIC support
BIOS-->AML ACPI table
Headless mode
[Enabled]
[Enabled]
[Enabled]
[Disabled]
Add additional tables
as per ACPI 2.0
specifications.
ACPI 2.0 Support [Enabled]
Specifies the Advanced Configuration and Power Interface (ACPI) version
supported. Configuration options: [Disabled] [Enabled]
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power Interface
(ACPI) support in the Advanced Programmable Interrupt Controller (APIC). When
set to [Enabled], the ACPI APIC table pointer is included in the RSDT pointer list.
Configuration options: [Disabled] [Enabled]
BIOS-->AML ACPI table [Enabled]
Allows you to include the BIOS-->AML exchange table pointer to (X)RSDT pointer
list.Configuration options: [Disabled] [Enabled]
Headless mode [Disabled]
Allows you to enable or disable the Headless operation mode through ACPI.
Configuration options: [Disabled] [Enabled]
ASUS Z8NH-D12 Series
4-31
Chipset ACPI Configuration
BIOS SETUP UTILITY
Advanced
South Bridge ACPI Configuration
APIC ACPI SCI IRQ
High Performance Event Timer
HPET Memory Address
[Disabled]
[Enabled]
[FED00000h]
Enable/Disable
APIC ACPI SCI IRQ
APIC ACPI SCI IRQ [Disabled]
Allows you to enable or disable the APIC ACPI SCI IRQ feature.
Configuration options: [Disabled] [Enabled]
High Performance Event Timer [Enabled]
Allows you to enable or disable the High Performance Event Timer feature.
Configuration options: [Disabled] [Enabled]
HPET Memory Address [FED00000h]
Allows you to select the HPET Memory address.
Configuration options: [FED00000h] [FED01000h] [FED02000h] [FED03000h]
General WHEA Configuration
Advanced
BIOS SETUP UTILITY
General WHEA Configuration
WHEA Support
[Enabled]
Enable or disable
Windows Hardware
Error Architecture.
WHEA Support [Enabled]
Allows you to enable or disable the Windows Hardware Error Architecture (WHEA)
support.Configuration options: [Disabled] [Enabled]
4-32
Chapter 4: BIOS setup
4.5
Main
Server menu
Advanced
BIOS SETUP UTILITY
Boot
Exit
Server
Configure Remote
Access.
Remote Access Configuration
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4.5.1
Remote Access Configuration
The items in this menu allows you to configure the Remote Access features. Select
an item then press <Enter> to display the configuration options.
Server
BIOS SETUP UTILITY
Configure Remote Access type and parameters
Remote Access
[Enabled]
Serial port number
Base Address, IRQ
Serial Port Mode
Flow Control
Redirection After BIOS POST
Terminal Type
[COM2]
[2F8h, 3]
[57600 8,n,1]
[Hardware]
[Disabled]
[VT-UTF8]
Select Remote Access
type.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Remote Access [Enabled]
Enables or disables the remote access feature.
Configuration options: [Disabled] [Enabled]
The following items appear only when Remote Access is set to [Enabled].
ASUS Z8NH-D12 Series
4-33
Serial port number [COM2]
Selects the serial port for console redirection.
Configuration options: [COM1] [COM2]
Base Address. IRQ [2F8h, 3]
This item is not user-configurable and changes with the configuration of
Serial port number.
Serial Port Mode [57600 8,n,1]
Sets the Serial port mode.
Configuration options: [115200 8,n,1] [57600 8,n,1] [38400 8,n,1] [19200 8,n,1]
[09600 8,n,1]
Flow Control [Hardware]
Allows you to select the flow control for console redirection.
Configuration options: [None] [Hardware] [Software]
Redirection After BIOS POST [Disabled]
Sets the redirection mode after the BIOS Power-On Self-Test (POST). Some
operating system may not work when set to [Always].
Configuration options: [Disabled] [Boot Loader] [Always]
Terminal Type [VT-UTF8]
Allows you to select the target terminal type.
Configuration options: [ANSI] [VT100] [VT-UTF8]
4-34
Chapter 4: BIOS setup
4.6
Boot menu
The Boot menu items allow you to change the system boot options. Select an item
then press <Enter> to display the sub-menu.
Main
Advanced
BIOS SETUP UTILITY
Boot
Exit
Server
Specifies the Boot
Device Priority
sequence.
Boot Settings
Boot Device Priority
Boot Settings Configuration
Security
A virtual floppy disk
drive (Floppy Drive B:
) may appear when you
set the CD-ROM drive
as the first boot
device.
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
4.6.1
Boot Device Priority
BIOS SETUP UTILITY
Boot
Boot Device Priority
1st
2nd
3rd
4th
5th
Boot
Boot
Boot
Boot
Boot
Device
Device
Device
Device
Device
[Removable Dev.]
[ATAPI CD-ROM]
[Hard Drive]
[Network:IBA GE Slo]
[Network:IBA GE Slo]
Specifies the Boot
Device Priority
sequence.
A device enclosed
in parenthesis has
been disabled in the
corresponding type
menu.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
1st—xxth Boot Device [XXXXXXX]
These items specify the boot device priority sequence from the available devices.
The number of device items that appears on the screen depends on the number of
devices installed in the system. Configuration options: [xxxxx Drive] [Disabled]
4.6.2
Hard Disk Drives; CDROM Drives
These two items appear only when you install more than two hard disk drives or
optical drives to you system. These items allows you to specify the boot priority
sequence of the hard disk drives or the optical drives.
ASUS Z8NH-D12 Series
4-35
4.6.3
Boot Settings Configuration
BIOS SETUP UTILITY
Boot
Boot Settings Configuration
Quick Boot Full Screen Logo
AddOn ROM Display Mode
Bootup Num-Lock
Wait For ‘F1‘ If Error
Hit ‘DEL‘ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Enabled]
[Enabled]
[Enabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
←→
↑↓
+F1
F10
ESC
Select Screen
Select Item
Change Option
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
AddOn ROM Display Mode [Force BIOS]
Allows you to set the display mode for Options ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
Wait For ‘F1‘ If Error [Enabled]
When set to [Enabled], the system waits for the <F1> key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]
Hit ‘DEL‘ Message Display [Enabled]
When set to [Enabled], the system displays the message “Press DEL to run Setup”
during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Enabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
Configuration options: [Disabled] [Enabled]
4-36
Chapter 4: BIOS setup
4.6.4
Security
The Security menu items allow you to change the system security settings. Select
an item then press <Enter> to display the configuration options.
BIOS SETUP UTILITY
Boot
Security Settings
Supervisor Password : Not Installed
User Password
: Not Installed
<Enter> to change
password.
<Enter> again to
disable password.
Change Supervisor Password
Change User Password
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Change
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default Not Installed. After you set
a password, this item shows Installed.
To set a Supervisor Password:
1.
Select the Change Supervisor Password item and press <Enter>.
2.
From the password box, type a password composed of at least six letters
and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message Password Installed appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a user
password.
To clear the supervisor password, select the Change Supervisor Password then
press <Enter>. The message Password Uninstalled appears.
If you forget your BIOS password, you can clear it by erasing the CMOS Real
Time Clock (RTC) RAM. See section 2.6 Jumper for information on how to
erase the RTC RAM.
ASUS Z8NH-D12 Series
4-37
After you have set a supervisor password, the other items appear to allow you to
change other security settings.
Main
Advanced
Server
BIOS SETUP UTILITY
Power
Boot
Tools
Supervisor Password : Installed
User Password
: Not Installed
Change Supervisor Password
User Access Level
Change User Password
Password Check
[Full Access]
Exit
<Enter> to change
password.
<Enter> again to
disable password.
[Setup]
User Access Level [Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
[No Access] prevents user access to the Setup utility.
[View Only] allows access but does not allow change to any field.
[Limited] allows changes only to selected fields, such as Date and Time.
[Full Access] allows viewing and changing all the fields in the Setup utility.
Change User Password
Select this item to set or change the user password. The User Password item on
top of the screen shows the default Not Installed. After you set a password, this
item shows Installed.
To set a User Password:
1.
Select the Change User Password item and press <Enter>.
2.
On the password box that appears, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message Password Installed appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user password.
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the Setup
utility. When set to [Always], BIOS checks for user password both when accessing
Setup and booting the system. Configuration options: [Setup] [Always]
4-38
Chapter 4: BIOS setup
4.7
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values for the
BIOS items, and save or discard your changes to the BIOS items.
Main
Advanced
Server
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
BIOS SETUP UTILITY
Boot
Exit
Exit system setup
after saving the
changes.
F10 key can be used
for this operation.
Load Setup Defaults
←→
↑↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.61 (C)Copyright 1985-2009, American Megatrends, Inc.
Pressing <Esc> does not immediately exit this menu. Select one of the options
from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are finished making your selections, choose this option from the Exit
menu to ensure the values you selected are saved to the CMOS RAM. An onboard
backup battery sustains the CMOS RAM so it stays on even when the PC is turned
off. When you select this option, a confirmation window appears. Select YES to
save changes and exit.
If you attempt to exit the Setup program without saving your changes, the
program prompts you with a message asking if you want to save your changes
before exiting. Press <Enter> to save the changes while exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you made to the
Setup program. If you made changes to fields other than System Date, System
Time, and Password, the BIOS asks for a confirmation before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation appears. Select
YES to discard any changes and load the previously saved values.
Load Setup Defaults
This option allows you to load the default values for each of the parameters on the
Setup menus. When you select this option or if you press <F5>, a confirmation
window appears. Select YES to load default values. Select Exit & Save Changes
or make other changes before saving the values to the non-volatile RAM.
ASUS Z8NH-D12 Series
4-39
4-40
Chapter 4: BIOS setup
This chapter provides instructions for
setting up, creating, and configuring RAID
sets using the available utilities.
5
RAID
configuration
Chapter summary
5
5.1
Setting up RAID............................................................................. 5-3
5.3
Intel® Matrix Storage Manager Option ROM Utility.................. 5-25
5.2
LSI Software RAID Configuration Utility..................................... 5-5
ASUS Z8NH-D12 Series
5.1
Setting up RAID
The motherboard comes with the following RAID solutions:
The motherboard comes with the Intel® ICH10R southbridge controller that
supports the following SATA RAID solutions:
•
LSI Software RAID Configuration Utility (default) with RAID 0, RAID 1, and
RAID 10 support (for both Linux and Windows OS).
•
Intel Matrix Storage Manager with RAID 0, RAID 1, RAID 10, and RAID 5
support (for Windows OS only).
5.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write
data in parallel, interleaved stacks. Two hard disks perform the same work as a
single drive but at a sustained data transfer rate, double that of a single disk alone,
thus improving data access and storage. Use of two new identical hard disk drives
is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one
drive to a second drive. If one drive fails, the disk array management software
directs all applications to the surviving drive as it contains a complete copy of
the data in the other drive. This RAID configuration provides data protection and
increases fault tolerance to the entire system. Use two new drives or use an
existing drive and a new drive for this setup. The new drive must be of the same
size or larger than the existing drive.
RAID 10 is data striping and data mirroring combined without parity (redundancy
data) having to be calculated and written. With the RAID 10 configuration you get
all the benefits of both RAID 0 and RAID 1 configurations. Use four new hard disk
drives or use an existing drive and three new drives for this setup.
RAID 5 stripes both data and parity information across three or more hard disk
drives. Among the advantages of RAID 5 configuration include better HDD
performance, fault tolerance, and higher storage capacity. The RAID 5 configuration
is best suited for transaction processing, relational database applications,
enterprise resource planning, and other business systems. Use a minimum of three
identical hard disk drives for this setup.
If you want to boot the system from a hard disk drive included in a created RAID
set, copy first the RAID driver from the support CD to a floppy disk before you
install an operating system to the selected hard disk drive.
ASUS Z8NH-D12 Series
5-3
5.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal
performance, install identical drives of the same model and capacity when creating
a disk array.
To install the SATA hard disks for RAID configuration:
1.
Install the SATA hard disks into the drive bays following the instructions in the
system user guide.
2.
Connect a SATA signal cable to the signal connector at the back of each drive
and to the SATA connector on the motherboard.
3.
Connect a SATA power cable to the power connector on each drive.
5.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set
from SATA hard disk drives attached to the SATA connectors supported by
Intel® ICH10R chipset. To do this:
1.
Enter the BIOS Setup during POST.
2.
Go to the Main Menu > IDE Configuration, then press <Enter>.
3.
Set Configure SATA as to [RAID]
4.
Press <F10> to save your changes and exit the BIOS Setup.
Refer to Chapter 4 for details on entering and navigating through the BIOS
Setup.
5.1.4
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set using
the utilities embedded in each RAID controller. For example, use the LSI Logic
Embedded SATA RAID Setup Utility or the Intel® Matrix Storage Manager if you
installed Serial ATA hard disk drives on the Serial ATA connectors supported by the
Intel® ICH10R chipset.
Refer to the succeeding section for details on how to use the RAID configuration
utility.
5-4
Chapter 5: RAID configuration
5.2
LSI Software RAID Configuration
Utility
The LSI MegaRAID software RAID configuration utility allows you to create RAID 0,
RAID 1, or RAID 10 set(s) from SATA hard disk drives connected to the SATA
connectors supported by the motherboard southbridge chip.
To enter the LSI MegaRAID software RAID configuration utility
1.
Turn on the system after installing all the SATA hard disk drives.
2.
During POST, the LSI MegaRAID software RAID configuration utility
automatically detects the installed SATA hard disk drives and displays any
existing RAID set(s). Press <Ctrl> + <M> to enter the utility.
LSI MegaRAID Software RAID BIOS Version A.08 09161344R
LSI SATA RAID Found at PCI Bus No: Dev No:1F
Device present at Port 0
ST3160812AS
152114MB
Device present at Port 1
ST3160812AS
152114MB
Device present at Port 2
ST3160812AS
152114MB
Device present at Port 3
ST3160812AS
152114MB
Press Ctrl-M or Enter to run LSI Software RAID Setup Utility.
•
The LSI MegaRAID software RAID configuration utility automatically
configures to RAID 1 when the SATA to RAID Mode is enabled.
•
The RAID setup screens shown in this section are for reference only and
may not exactly match the items on your screen due to the controller
version difference.
•
When you create RAID sets with the LSI MegaRAID software RAID
configuration utility, the boot priority of the SATA optical drive has to be
manually adjusted. Otherwise, the system will not boot from the connected
SATA ODD.
3.
The utility main window appears. Use the arrow keys to select an option from
the Management Menu and then press <Enter>. Refer to the Management
Menu descriptions on the next page.
At the bottom of the screen is the legend box. The keys on the legend box
allow you to navigate through the setup menu options or execute commands.
The keys on the legend box vary according to the menu level.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Configure VD(s)
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
ASUS Z8NH-D12 Series
5-5
Menu
Description
Configure
Allows you to create RAID 0, RAID 1 or RAID 10 set using the Easy
Configuration or the New Configuration command. This menu also
allows you to view, add, or clear RAID configurations or select the
boot drive
Initialize
Allows you to initialize the virtual drives of a created RAID set
Objects
Allows you to initialize virtual drives or change the virtual drive
parameters
Rebuild
Allows you to rebuild failed drives
Check Consistency Allows you to check the data consistency of the virtual drives of a
created RAID set
5.2.1
Creating a RAID set
The LSI Software RAID Configuration Utility allows you to create a RAID 0, RAID 1,
or RAID 10 set using two types of configurations: Easy and New.
In Easy Configuration, the virtual drive parameters are set automatically.
In New Configuration, you manually set the virtual drive parameters.
Using Easy Configuration
To create a RAID set using the Easy Configuration option
1.
From the Management Menu, select Configure > Easy Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Defines Physical Arrays. An Array Will Automatically Become A VD
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5-6
Chapter 5: RAID configuration
2.
The ARRAY SELECTION MENU displays the available drives connected to
the SATA ports. Use the up/down arrow key to select the drives you want to
include in the RAID set, and then press <Space>. When selected, the drive
indicator changes from READY to ONLIN A[X]-[Y], where X is the array
number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Easy Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
PORT #
0 ONLIN A00-00
1 ONLIN A00-01
2 READY
3 READY
Port # 1 DISK
77247MB
HDS728080PLA380
PF20A60A
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
•
The information of the selected hard disk drive displays at the bottom of the
screen.
•
You need at least two identical hard disk drives when creating a RAID 1 set.
•
You need at least four identical hard disk drives when creating a RAID 10
set.
3.
Select all the drives required for the RAID set, and then press <F10> to
configure array setting.
4.
Press <Space> to select the configurable array.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Easy Configuration - ARRAY SELECTION MENU
Select Configurable Array(s)
PORT #
A-0
0 DNLIN A00-00
SPAN-1
1 DNLIN A00-01
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
ASUS Z8NH-D12 Series
5-7
5.
Press <F10> again, the virtual drive information appears including a Virtual
Drive menu that allows you to change the virtual drive parameters.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Virtual
VersionDrive(s)
A.08.09161344R
Configured
LD
RAID
Size
#Stripes
StripSzMENU Status
Easy Configuration
- ARRAY SELECTION
0
1
77247MB
2
64 KB
ONLINE
Management Menu
PORT #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virgual Drive 0
RAID = 1
Size = 77247MB
DWC = Off
RA = On
Accept
SPAN = NO
Choose RAID Level For This VD
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
6.
7.
Select RAID from the Virtual Drive sub-menu, and then press <Enter>.
Select the RAID level from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Virtual
VersionDrive(s)
A.08.09161344R
Configured
LD
RAID
Size
#Stripes
StripSzMENUStatus
Easy Configuration
- ARRAY SELECTION
0
1
77247MB
2
64 KB
ONLINE
Management Menu
PORT #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virtual Drive 0
RAID Level
RAID = 1
RAID 0
Size = 77247MB
RAID 1
DWC = Off
RA = On
Accept
SPAN = NO
Choose RAID Level For This VD
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
5-8
Chapter 5: RAID configuration
8.
9.
When creating a RAID 1 or a RAID 10 set, select DWC from the Virtual
Drive menu, and then press <Enter>.
When creating a RAID 0 set, proceed to step 10.
Select On to enable the Disk Write Cache setting, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOSVirtual
VersionDrive(s)
A.08.09161344R
Configured
LD
RAID
Size
#Stripes
StripSzMENUStatus
Easy Configuration
- ARRAY SELECTION
0
1
77247MB
2
64 KB
ONLINE
Management Menu
PORT #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01Change DWC
Rebuild
Off
Check Consistency
On
Virtual Drive 0
RAID = 1
Size = 77247MB
DWC = Off
RA = On
Accept
SPAN = NO
Disk Write Cache Setting Of VD
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
Enabling DWC can improve the performance, but with the risk of data loss.
10. When finished setting the selected virtual drive configuration, select Accept
from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Virtual
VersionDrive(s)
A.08.09161344R
Configured
LD
RAID
Size
#Stripes
StripSzMENUStatus
Easy Configuration
- ARRAY SELECTION
0
1
77247MB
2
64 KB
ONLINE
Management Menu
PORT #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Virtual Drive 0
RAID = 1
Size = 77247MB
DWC = Off
RA = On
Accept
SPAN = NO
Accept This VD Configuration And Go To Next VD
Cursor Keys, SPACE-(De)Select F2-ChIdInfo F3-SlotInfo F10-Configure Esc-Quit
ASUS Z8NH-D12 Series
5-9
11. Follow step 2 to 10 to configure additional virtual drives.
12. Press <Esc> to finish RAID configuration. When prompted to save
configuration, select Yes from the menu, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Save Configuration?
Easy Configuration
Yes
New Configuration
Management Menu
No
View/Add Configuration
Configure
Clear Configuration
Initialize
Virtual Drive(s) Configured
Boot Drive
Objects
LD Select
RAID
Size
#Stripes
StripSz Status
Rebuild
0
1
77247MB
2
64 KB
ONLINE
Check Consistency
Select Yes Or No
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
Using New Configuration
When a RAID set already exists, using the New Configuration command
erases the existing RAID configuration data. If you do not want to delete the
existing RAID set, use the View/Add Configuration command to view or create
another RAID configuration.
To create a RAID set using the New Configuration option
1.
From the Management Menu, select Configure > New Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration And Start A New Configuration
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5-10
Chapter 5: RAID configuration
2.
Follow step 2 to 7 of the previous section: Using Easy Configuration.
3.
Select Size from the Virtual Drive menu, and then press <Enter>.
4.
Key-in the desired virtual drive size, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Virtual
VersionDrive(s)
A.08.09161344R
Configured
LD
RAID
Size
#Stripes
StripSzMENUStatus
Easy Configuration
- ARRAY SELECTION
0
1
77247MB
2
64 KB
ONLINE
Management Menu
PORT #
Configure
0 DNLIN A00-00
Initialize
Objects
1 DNLIN A00-01
Rebuild
Check Consistency
Enter VD Size (MB): 77247
Virtual Drive 0
RAID = 1
Size = 77247MB
DWC = Off
RA = On
Accept
SPAN = NO
Enter VD Size (MB):
Use Cursor Keys to Navigate Between Items And Press Enter To Select An Option
5.
Follow step 8 to 12 of the previous section: Using Easy Configuration to
create the RAID set.
ASUS Z8NH-D12 Series
5-11
5.2.2
Adding or viewing a RAID configuration
You can add a new RAID configuration or view an existing configuration using the
View/Add Configuration command.
Adding a new RAID configuration
To add a new RAID configuration:
1.
From the Management Menu, select Configure > View/Add Configuration,
and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
View/Add to The Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The ARRAY SELECTION MENU displays the available drives connected to
the SATA ports. Select the drive(s) you want to include in the RAID set, then
press <Space>. When selected, the drive indicator changes from READY to
ONLIN A[X]-[Y], where X is the array number, and Y is the drive number.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
View/Add Configuration - ARRAY SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 2 DISK
PORT #
0 ONLIN A00-00
1 ONLIN A00-01
2 READY
3 READY
77247MB
HDS728080PLA380
PF20A60A
SPACE-Sel,ENTER-EndArray,F10-Configure,F2-Drive Info,F3-Virtual Drives,F4-HSP
The information of the selected hard disk drive displays at the bottom of the
screen.
3.
5-12
Follow step 3 to 12 of section 5.2.1 Creating a RAID set: Using Easy
Configuration to add a new RAID set.
Chapter 5: RAID configuration
5.2.3
Initializing the virtual drives
After creating the RAID set(s), you must initialize the virtual drives. You may
initialize the virtual drives of a RAID set(s) using the Initialize or Objects command
on the Management Menu.
Using the Initialize command
To initialize the virtual drive using the Initialize command
1.
From the Management Menu, select Initialize, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Initialize Virtual Drive(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select the
virtual drive to initialize. Use the arrow keys to select the virtual drive from the
Virtual Drive selection, and then press <Space>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
RAID
0
1
Virtual Drive(s) Configured
Size
#Stripes
StripSz
Status
151634MB
ONLINE
2
64 KB
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select, F10-Initialize
ASUS Z8NH-D12 Series
5-13
3.
Press <F10> to start initialization. When prompted, select Yes from the
Initialize? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
RAID
Size
#Stripes
StripSz
10 154494MB
4
64 KB
Status
ONLINE
Initialize?
Yes
No
Virtual Drives
Virtual Drive 0
Init Will Destroy Data On Selected VD(s)
SPACE-(De)Select, F10-Initialize
Initializing a virtual drive erases all data on the drive.
4.
A progress bar appears on screen. If desired, press <Esc> to abort
initialization. When initialization is completed, press <Esc>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Virtual Drive(s) Configured
Management Menu
LD
RAID
Size
#Stripes
StripSz
Configure
0 Init10Of VD
154494MB
4
64 KB
Is In Process
Initialize
Objects
VD 0 Initialization Complete. Press Esc..
Rebuild
Check Consistency
Status
ONLINE
¦ 100% Completed
Virtual Drives
Virtual Drive 0
SPACE-(De)Select, F10-Initialize
5-14
Chapter 5: RAID configuration
Using the Objects command
To initialize the virtual drives using the Objects command
1.
From the Management Menu, select Objects > Virtual Drive, and then
press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Change VD Parameters
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
Select the virtual drive to initialize from the Virtual Drives sub‑menu, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Rebuild
Check Consistency
Select VD
Press ENTER To Select A VD, <Del> To Delete A VD
ASUS Z8NH-D12 Series
5-15
3.
Select Initialize from the pop-up menu, and then press <Enter> to start
initialization.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Vitual Drive(0)
Rebuild
Initialze
Check Consistency
Check Consistency
View/Update Parameters
Initilize VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
4.
When prompted, press the <Space> to select Yes from the Initialize? dialog
box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Vitual Drive(1)
Virtual Drive 0
Objects
Management Menu
Adapter
Configure
Virtual Drive
Initialize
Physical Drive
Objects
Vitual Drive(0)
Rebuild
Initialze
Check Consistency
Initialize?
Check Consistency
Yes
View/Update Parameters
No
Initilize Will Destroy Data On Selected VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5.
5-16
A progress bar appears on screen. If desired, press <Esc> to abort
initialization. When initialization is completed, press <Esc>.
Chapter 5: RAID configuration
5.2.4
Rebuilding failed drives
You can manually rebuild failed hard disk drives using the Rebuild command in the
Management Menu.
To rebuild a failed hard disk drive
1.
From the Management Menu, select Rebuild, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Rebuild PD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The PHYSICAL DRIVES SELECTION MENU displays the available drives
connected to the SATA ports. Select the drive you want to rebuild, and then
press <Space>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
Port # 1 DISK
PORT #
0 ONLIN A00-00
1 FAIL A00-01
77247MB
HDS728080PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
ASUS Z8NH-D12 Series
5-17
3.
After selecting the drive to rebuild, press <F10>. When prompted, press <Y>
to rebuild the drive.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
REBUILD - PHYSICAL DRIVES SELECTION MENU
Management Menu
PORT #
Configure
0 ONLIN A00-00
Initialize
Objects
1 RBLD A00-01
Rebuild
Check Consistency
Rebuilding
Of Drive Will Take A Few Minutes. Start Rebuilding Drive (Y/N)?
Port # 1 DISK
77247MB
HDS728080PLA380
PF20A60A
SPACE-(De)Select,F10-Start Rebuild,F2-Drive Information,F3-View Virtual Drives
4.
5-18
When rebuild is complete, press any key to continue.
Chapter 5: RAID configuration
5.2.5
Checking the drives for data consistency
You can check and verify the accuracy of data redundancy in the selected virtual
drive. The utility can automatically detect and/or detect and correct any differences
in data redundancy depending on the selected option in the Objects > Adapter
menu.
The Check Consistency command is available only for virtual drives included
in a RAID 1 or RAID 10 set.
Using the Check Consistency Command
To check data consistency using the Check Consistency command
1.
From the Management Menu, select Check Consistency, and then press
<Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
CC Of VD(s)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
The screen displays the available RAID set(s) and prompts you to select
the virtual drive to check. Press <Space> to select the virtual drive from the
Virtual Drive sub-menu, and then press <F10>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
RAID
Size
#Stripes
StripSz
10 154494MB
4
64 KB
Status
ONLINE
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select,
ASUS Z8NH-D12 Series
F10-Check Consistency
5-19
3.
When prompted, use the arrow keys to select Yes from the Consistency
Check? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Management Menu
Configure
Initialize
Objects
Rebuild
Check Consistency
LD
0
Virtual Drive(s) Configured
RAID
Size
#Stripes
StripSz
10 154494MB
4
64 KB
Yes
No
Status
ONLINE
Consistency Check?
Virtual Drives
Virtual Drive 0
Select VD
SPACE-(De)Select,
F10-Check Consistency
A progress bar appears on screen.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Virtual Drive(s) Configured
Management Menu
LD
RAID
Size
#Stripes
StripSz
Configure
0
10
154494MB
64 KB
CC Under
Process 4
Initialize
Objects
VD 0 Consistency Check. Press Esc to Abort.
Rebuild
Check Consistency
Status
ONLINE
¦ 85 % Completed
Virtual Drives
Virtual Drive 0
The Data On The Drives Is Inconsistency. Repair Done!
SPACE-(De)Select,
5-20
F10-Check Consistency
4.
While checking the disk consistency, press <Esc> to display the following
options.
• Stop
• Continue- Continues the consistency check.
• Abort
5.
When checking is complete, press any key to continue.
- Stops the consistency check. The utility stores the
percentage of disk checked, and when you restart checking,
it continues from the last percentage completed rather than
from zero percent.
- Aborts the consistency check. When you restart checking, it
continues from zero percent.
Chapter 5: RAID configuration
Using the Objects command
To check data consistency using the Objects command
1.
From the Management Menu, select Objects, and then select Virtual Drive
from the sub-menu.
2.
Use the arrow keys to select the virtual drive you want to check, and then
press <Enter>.
3.
Select Check Consistency from the pop-up menu, and then press <Enter>.
4.
When prompted, use the arrow keys to select Yes from the dialog box to
check the drive.
5.
When checking is complete, press any key to continue.
ASUS Z8NH-D12 Series
5-21
5.2.6
Deleting a RAID configuration
To delete a RAID configuration
1.
From the Management Menu, select Configure > Clear Configuration, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select Yes from the Clear
Configuration? dialog box, and then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
Clear Configuration?
View/Add Configuration
Configure
Yes
Clear Configuration
Initialize
No
Select
Boot
Drive
Objects
Rebuild
Check Consistency
Clear Existing Configuration
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
5-22
The utility clears all the current array(s).
3.
Press any key to continue.
Chapter 5: RAID configuration
5.2.7
Selecting the boot drive from a RAID set
You must have created a new RAID configuration before you can select the
boot drive from a RAID set. See section 5.2.1 Creating a RAID set: Using New
Configuration for details.
To select the boot drive from a RAID set
1.
From the Management Menu, select Configure > Select Boot Drive, and
then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Configuration Menu
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
2.
When prompted, use the arrow keys to select the bootable virtual drive from
the list, then press <Enter>.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Bootable VDs(1):Current Boot VD(0)
Configuration
BootMenu
Drive 0
Easy Configuration
New Configuration
Management Menu
View/Add Configuration
Configure
Clear Configuration
Initialize
Select Boot Drive
Objects
Rebuild
Check Consistency
Select A Boot VD
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
The virtual drive is selected as boot drive. Press any key to continue.
ASUS Z8NH-D12 Series
5-23
5.2.8
Enabling WriteCache
You may manually enable the RAID controller’s WriteCache option after creating a
RAID set to improve the data transmission performance.
When you enable WriteCache, you may lose data when a power interruption occurs
while transmitting or exchanging data among the drives.
The WriteCache function is recommended for RAID 1 and RAID 10 sets.
To enable WriteCache
1.
From the Management Menu, select Objects > Adapter, and then press
<Enter> to display the adapter properties.
2.
Select Disk WC, and then press <Enter> to turn on the option.
LSI Software RAID Configuration Utility Ver A.60 Jul 30, 2008
BIOS Version A.08.09161344R
Adapter 0
Rebuild Rate = 30
ObjectsChk Const Rate = 30
Management Menu
Adapter
FGI Rate
= 30
Configure
Virtual Drive BGI Rate
= 30
Initialize
Physical DriveDisk WC
= Off
Objects
Read Ahead
= On
Rebuild
Bios State
= Enable
Check Consistency
Stop On Error = No
Fast Init
= Enable
Auto Rebuild = On
Auto Resume
= Enable
Disk Coercion = 1GB
Factory Default
Disk Write Cache - Off(Write Through) or On(Write Back)
Use Cursor Keys To Navigate Between Items And Press Enter To Select An Option
3.
5-24
When finished, press any key to continue.
Chapter 5: RAID configuration
5.3
Intel® Matrix Storage Manager
Option ROM Utility
The Intel® Matrix Storage Manager Option ROM utility allows you to create RAID 0,
RAID 1, RAID 10 (RAID 0+1), and RAID 5 set(s) from Serial ATA hard disk drives
that are connected to the Serial ATA connectors supported by the Southbridge.
To enter the Intel® Matrix Storage Manager option ROM utility:
1.
Install all the Serial ATA hard disk drives.
2.
Turn on the system.
3.
During POST, press <Ctrl+I> to display the utility main menu.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
5. Exit
3. Reset Disks to Non-RAID
4. Recovery Volume Options
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
None defined.
Physical Disks:
Port Drive Model
0
ST3160812AS
1
ST3160812AS
2
ST3160812AS
3
ST3160812AS
[↑↓]-Select
* = Data is Encrypted
Serial #
9LS0HJA4
9LS0F4HL
3LS0JYL8
9LS0BJ5H
[ESC]-Exit
Size
149.0GB
149.0GB
149.0GB
149.0GB
Type/Status(Vol ID)
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
Non-RAID Disk
[ENTER]-Select Menu
The navigation keys at the bottom of the screen allow you to move through
the menus and select the menu options.
The RAID BIOS setup screens shown in this section are for reference only and
may not exactly match the items on your screen.
The utility supports maximum four hard disk drives for RAID configuration.
ASUS Z8NH-D12 Series
5-25
5.3.1
Creating a RAID set
To create a RAID set
1.
From the utility main menu, select 1. Create RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Sync:
Volume0
RAID0(Stripe)
Select Disks
128KB
0.0
GB
N/A
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[↑↓]Change
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
2.
Enter a name for the RAID set and press <Enter>.
3.
When the RAID Level item is selected, press the up/down arrow key to select
a RAID level to create, and then press <Enter>.
4.
When the Disks item is selected, press <Enter> to select the hard disk drives
you want to include in the RAID set. The SELECT DISKS screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
ST3160812AS
ST3160812AS
ST3160812AS
ST3160812AS
Serial #
9LS0HJA4
9LS0F4HL
3LS0JYL8
9LS0BJ5H
Size
149.0GB
149.0GB
149.0GB
149.0GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 2 to 6 disks to use in creating the volume.
[↑↓]-Prev/Next [SPACE]-SelectDisk [ENTER]-Done
5.
5-26
Use the up/down arrow key to select a drive, and then press <Space>
to select. A small triangle marks the selected drive. Press <Enter> after
completing your selection.
Chapter 5: RAID configuration
6.
Use the up/down arrow key to select the stripe size for the RAID array (for
RAID 0, 10 and 5 only), and then press <Enter>. The available stripe size
values range from 4 KB to 128 KB. The following are typical values:
RAID 0: 128KB
RAID 10: 64KB
RAID 5: 64KB
We recommend a lower stripe size for server systems, and a higher stripe size
for multimedia computer systems used mainly for audio and video editing.
7.
When the Capacity item is selected, enter the RAID volume capacity that you
want and press <Enter>. The default value indicates the maximum allowed
capacity.
8.
When the Create Volume item is selected, press <Enter>. The following
warning message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
9.
Press <Y> to create the RAID volume and return to the main menu, or <N> to
go back to the CREATE VOLUME menu.
5.3.2
Creating a Recovery set
To create a recovery set
1.
From the utility main menu, select 1. Create RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ CREATE VOLUME MENU ]
Name:
RAID Level:
Disks:
Strip Size:
Capacity:
Sync:
Volume0
RAID0(Stripe)
Select Disks
128KB
0.0
GB
N/A
Create Volume
[ HELP ]
Enter a unique volume name that has no special characters and is
16 characters or less.
[↑↓]Change
ASUS Z8NH-D12 Series
[TAB]-Next
[ESC]-Previous Menu
[ENTER]-Select
5-27
2.
Enter a name for the recovery set and press <Enter>.
3.
When the RAID Level item is selected, press the up/down arrow key to select
Recovery, and then press <Enter>.
4.
When the Disks item is selected, press <Enter> to select the hard disk drives
you want to include in the recovery set. The SELECT DISKS screen appears.
[ SELECT DISKS ]
Port
0
1
2
3
Drive Model
ST3160812AS
ST3160812AS
ST3160812AS
ST3160812AS
Serial #
9LS0HJA4
9LS0F4HL
3LS0JYL8
9LS0BJ5H
Size
149.0GB
149.0GB
149.0GB
149.0GB
Status
Non-RAID
Non-RAID
Non-RAID
Non-RAID
Disk
Disk
Disk
Disk
Select 1 Master and 1 Recovery disk to create volume.
[↑↓]-Prev/Next [TAB]-(M)aster [SPACE]-(R)ecovery [ENTER]-Done
5.
Use the up/down arrow key to select a drive, press <TAB> to select a Master
disk, and then press <SPACE> to select a Recovery disk. A small triangle
marks the selected drive. Press <Enter> after completing your selection.
6.
When the Sync item is selected, use the up/down arrow key to select a sync
option that you want and press <Enter>.
7.
When the Create Volume item is selected, press <Enter>. The following
warning message appears.
WARNING: ALL DATA ON SELECTED DISKS WILL BE LOST.
Are you sure you want to create this volume? (Y/N):
8.
Press <Y> to create the recovery set and return to the main menu, or <N> to
go back to the CREATE VOLUME menu.
If a recovery set is created, you cannot add more RAID sets even when you
have more non-RAID disks installed in your system.
5-28
Chapter 5: RAID configuration
5.3.3
Deleting a RAID set
Take caution when deleting a RAID set. You will lose all data on the hard disk
drives when you delete a RAID set.
To delete a RAID set
1.
From the utility main menu, select 2. Delete RAID Volume and press
<Enter>. The following screen appears.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ DELETE VOLUME MENU ]
Name
Volume0
Level
RAID0(Stripe)
Drives
2
Capacity
298.0GB
Status
Normal
Bootable
Yes
[ HELP ]
Deleting a volume will reset the disks to non-RAID.
WARNING: ALL DISK DATA WILL BE DELETED.
(This does not apply to Recovery volumes)
[↑↓]-Select
2.
[ESC]-Previous Menu
[DEL]-Delete Volume
Use the up/down arrow key to select the RAID set you want to delete, and
then press <Del>. The following warning message appears.
[ DELETE VOLUME VERIFICATION ]
ALL DATA IN THE VOLUME WILL BE LOST!
(This does not apply to Recovery volumes)
Are you sure you want to delete volume “Volume0”? (Y/N):
3.
Press <Y> to delete the RAID set and return to the utility main menu, or press
<N> to return to the DELETE VOLUME menu.
ASUS Z8NH-D12 Series
5-29
5.3.4
Resetting disks to Non-RAID
Take caution before you reset a RAID volume hard disk drive to non-RAID.
Resetting a RAID volume hard disk drive deletes all internal RAID structure on
the drive.
To reset a RAID set hard disk drive
1.
From the utility main menu, select 3. Reset Disks to Non-RAID and press
<Enter>. The following screen appears.
[ RESET RAID DATA ]
Resetting RAID disk will remove its RAID structures
and revert it to a non-RAID disk.
WARNING: Resetting a disk causes all data on the disk to be lost.
(This does not apply to Recovery volumes)
Port Drive Model
0
ST3160812AS
1
ST3160812AS
Serial #
9LS0HJA4
9LS0F4HL
Size
149.0GB
149.0GB
Status
Member Disk
Member Disk
Select the disks that should be reset.
[↑↓]-Previous/Next
5-30
[SPACE]-Selects [ENTER]-Selection Complete
2.
Use the up/down arrow key to select the RAID set drive(s) you want to reset,
and then press <Space> to select.
3.
Press <Enter> to reset the RAID set drive(s). A confirmation message
appears.
4.
Press <Y> to reset the drive(s) or press <N> to return to the utility main
menu.
Chapter 5: RAID configuration
5.3.5
Recovery Volume Options
If you have created a recovery set, you can configure more recovery set options
following the descriptions in the section.
See section 5.3.2 Creating a Recovery set to create a recovery set before
continue.
To configure a recovery set
1.
From the utility main menu, select 4. Recovery Volume Options and press
<Enter>. The following screen appears.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ RECOVERY VOLUME OPTIONS ]
1.
2.
Enable Only Recovery Disk
Enable Only Master Disk
[ HELP ]
Enable Only Recovery Disk - enables recovery disk if available and
disables master disk.
Enable Only Master Disk - enables master disk if available and
disables recovery disk.
Actions will result in change from Continuous Update mode to On-Request.
[↑↓]-Select
2.
[ESC]-Previous Menu
[ENTER]-Select
Use the up/down arrow key to select the option you want, and then press
<ENTER>. The SELECT RECOVERY VOLUME screeen appears.
[ SELECT RECOVERY VOLUME ]
Name
Volume0
Level
Capacity
Status
Recovery(Cont.)
149.0GB
Normal
Bootable
Yes
Select a Recovery volume to do the operation.
[↑↓]-Up/Down [SPACE]-Selects [ENTER]-Done
3.
Use the up/down arrow key to select a drive, and then press <Space>
to select. A small triangle marks the selected drive. Press <Enter> after
completing your selection and return to the utility main menu.
ASUS Z8NH-D12 Series
5-31
5.3.6
Exiting the Intel® Matrix Storage Manager
To exit the utility
1.
From the utility main menu, select 5. Exit, and then press <Enter>. The
following warning message appears.
[ CONFIRM EXIT ]
Are you sure you want to exit? (Y/N):
2.
Press <Y> to exit or press <N> to return to the utility main menu.
5.3.7
Rebuilding the RAID
This option is only for the RAID 1 set.
Rebuilding the RAID with other non-RAID disk
If any of the SATA hard disk drives included in the RAID 1 array failed, the system
displays the status of the RAID volume as “Degraded” during POST. You can
rebuild the RAID array with other installed non-RAID disks.
To rebuild the RAID with other non-RAID disk:
1.
At the prompt, press <Ctrl> + <I> to enter the Intel Matrix Storage Manager
option ROM utility.
2.
If there is a non-RAID SATA Hard Disk available, the utility will prompt to
rebuild the RAID. Press <Enter>, and then use up/down arrow keys to select
the destination disk or press <ESC> to exit.
[ DEGRADED VOLUME DETECTED ]
"Degraded" volume and disk available for rebuilding detected. Selecting
a disk initiates a rebuild. Rebuild completes in the operating system.
Select the port of destination disk for rebuilding (ESC to exit):
Port Drive Model
Serial #
Size
X
XXXXXXXXXXX
XXXXXXXX
XX.XGB
[↑↓]-Previous/Next
[ENTER]-Select
[ESC]-Exit
Select a destination disk with the same size as the original hard disk.
5-32
Chapter 5: RAID configuration
3.
The utility immediately starts rebuilding after the disk is selected. The status
of the degraded RAID volume is changed to “Rebuild”.
Intel(R) Matrix Storage Manager option ROM v8.5.0.1030 ICH10R/DO wRAID5
Copyright(C) 2003-08 Intel Corporation. All Rights Reserved.
[ MAIN MENU ]
1. Create RAID Volume
2. Delete RAID Volume
3. Reset Disks to Non-RAID
4. Recovery Volume Options
5. Exit
[ DISK/VOLUME INFORMATION ]
RAID Volumes:
ID
Name
0
Volume0
Physical Disks:
Port Drive Model
1
ST3160812AS
2
ST3160812AS
Level
RAID1(Mirror)
Strip
N/A
Serial #
9LS0F4HL
3LS0JYL8
Size
149.0GB
Size
149.0GB
149.0GB
* = Data is Encrypted
Status
Bootable
Rebuild
Yes
Type/Status(Vol ID)
Member Disk(0)
Member Disk(0)
Volumes with “Rebuild” status will be rebuilt within the operating system.
[↑↓]-Select
[ESC]-Exit
[ENTER]-Select Menu
4.
Exit Intel Matrix Storage Manager and reboot the system.
5.
Select Start > Programs > Intel Matrix Storage > Intel Matrix Storage
Console or click the Intel Matrix Storage Manager tray icon to load the Intel
Matrix Stroage Manager utility.
6.
From the View menu, select Advanced Mode to display the details of the
Intel Matrix Storage Console.
7.
From the Volumes view option, select RAID volume to view the rebuilding
status. When finished, the status is changed to “Normal”.
Rebuilding the RAID with a new hard disk
If any of the SATA hard disk drives included in the RAID array failed, the system
displays the status of the RAID volume as “Degraded” during POST. You may
replace the disk drive and rebuild the RAID array.
To rebuild the RAID with a new hard disk:
1.
Remove the failed SATA hard disk and install a new SATA hard disk of the
same specification into the same SATA Port.
Select a destination disk with the same size as the original hard disk.
2.
Reboot the system and then follow the steps in section Rebuilding the
RAID with other non-RAID disk on page 5-32.
ASUS Z8NH-D12 Series
5-33
5.3.8
Setting the Boot array in the BIOS Setup Utility
You can set the boot priority sequence in the BIOS for your RAID arrays when
creating multi-RAID using the Intel® Matrix Storage Manager.
To set the boot array in the BIOS:
Set at least one of the arrays bootable to boot from the hard disk.
1.
Reboot the system and press <Del> to enter the BIOS setup utility during
POST.
2.
Go to the Boot menu and select the option Boot Device Priority.
3.
Use up/down arrow keys to select the boot priority and press <Enter>. See
section 4.6.1 Boot Device Priority for details.
4.
5.
5-34
From the Exit menu, select Exit & Save Changes, then press <Enter>.
When the confirmation window appears, select OK, then press <Enter>.
Chapter 5: RAID configuration
This chapter provides instructions for
installing the necessary drivers for
different system components.
6
Driver
installation
Chapter summary
6
6.1
RAID driver installation................................................................ 6-3
6.3
LAN driver installation................................................................ 6-23
6.2
6.4
6.5
6.6
Intel chipset device software installation................................. 6-19
Display driver installation.......................................................... 6-27
Mellanox ConnectX DDR and ConnectX2 QDR PCI Gen2
Channel Adapter driver installation.......................................... 6-30
Management application and utilities installation................... 6-37
ASUS Z8NH-D12 Series
6.1
RAID driver installation
After creating the RAID sets for your server system, you are now ready to install
an operating system to the independent hard disk drive or bootable array. This
part provides instructions on how to install the RAID controller drivers during OS
installation.
6.1.1
Creating a RAID driver disk
You may have to use another system to create the RAID driver disk from the
system/motherboard support DVD or from the Internet.
A floppy disk with the RAID driver is required when installing Windows® or
Red Hat® Enterprise operating system on a hard disk drive that is included in
a RAID set. You can create a RAID driver disk in DOS (using the Makedisk
application in the support DVD).
To create a RAID driver disk in DOS environment:
1.
Place the motherboard support DVD in the optical drive.
2.
Restart the computer, then enter the BIOS Setup.
3.
Select the optical drive as the first boot priority to boot from the support DVD.
Save your changes, then exit the BIOS Setup.
4.
Restart the computer.
The Makedisk menu appears.
Create Driver Diskette Menu
ICH10R INTEL RAID Driver
ICH10R LSI RAID Driver
ITE IT8213F Linux Driver
Write DMI
FreeDOS command prompt
5.
Use the arrow keys to select the type of RAID driver disk you want to ceate
and press <Enter> to enter the sub-menu.
ASUS Z8NH-D12 Series
6-3
ICH10R Intel RAID Driver
ICH10R INTEL RAID Driver
Windows 32 bit
Windows 64 bit
Back
Exit
ICH10R LSI RAID Driver
ICH10R LSI RAID Driver
Windows XP 32 bit
Windows XP 64 bit
Windows Server 2003 32 bit
Windows Server 2008 64 bit
Windows Vista 32 bit
Windows Vista 64 bit
Windows Server 2008 32 bit
Windows Server 2008 64 bit
RHEL AS4 UP6 32/64 bit
RHEL AS4 UP7 32/64 bit
RHEL 5 UP1 32/64 bit
RHEL 5 UP2 32/64 bit
SLES 9 SP3 32 bit
SLES 9 SP3 64 bit
SLES 9 SP4 32 bit
SLES 9 SP4 64 bit
SLES 10 SP1 32 bit
SLES 10 SP1 64 bit
SLES 10 SP2 32 bit
SLES 10 SP2 64 bit
Back
Exit
6-4
Chapter 6: Driver installation
ITE IT8213F Linux Driver
ITE IT8213F Linux Driver
RHEL 4 UP6 32/64 bit
RHEL 4 UP7 32/64 bit
RHEL 5 UP1 32/64 bit
RHEL 5 UP2 32/64 bit
SLES 9 SP3 32 bit
SLES 9 SP3 64 bit
SLES 10 32 bit
SLES 10 64 bit
FreeBSD 7 32/64 bit
Back
Exit
6.
Locate the RAID driver and place a blank, high-density floppy disk to the
floppy disk drive.
7.
Press <Enter>.
8.
Follow screen instructions to create the driver disk.
ASUS Z8NH-D12 Series
6-5
6.1.2
Windows® OS
During Windows® OS installation
To install the RAID controller driver when installing Windows® OS:
1.
Boot the computer using the Windows® OS installation CD. The Window®
Setup starts.
2.
Press <F6> when the message “Press F6 if you need to install a third party
SCSI or RAID driver...” appears at the bottom of the screen.
Windows Setup
Press F6 if you need to install a third party SCSI or RAID driver...
3.
The next screen appears. Press <S> to specify an additional device.
Windows Setup
Setup could not determine the type of one or more mass storage devices
installed in your system, or you have chosen to manually specify an adapter.
Currently, Setup will load support for the following mass storage
devices(s):
<none>
* To specify additional SCSI adapters, CD-ROM drives, or special
disk controllers for use with Windows, including those for
which you have a device support disk from a mass storage device
manufacturer, press S.
* If you do not have any device support disks from a mass storage
device manufacturer, or do not want to specify additional
mass storage devices for use with Windows, press ENTER.
S=Specify Additional Device
6-6
ENTER=Continue
F3=Exit
Chapter 6: Driver installation
4.
Insert the RAID driver disk you created earlier to the floppy disk drive, then
press <Enter>.
Windows Setup
Please insert the disk labeled
Manufacturer-supplied hardware support disk
into Drive A:
* Press ENTER when ready.
ENTER=Continue
ESC=Cancel
F3=Exit
5.
Select the RAID controller driver you need from the list, then press <Enter>.
6.
The Windows® Setup loads the RAID controller drivers from the RAID driver
disk. When next screen appears, press <Enter> to continue installation.
7.
Setup then proceeds with the OS installation. Follow screen instructions to
continue.
ASUS Z8NH-D12 Series
6-7
To an existing Windows® OS
To install the RAID controller driver on an existing Windows® OS:
1.
2.
3.
Restart the computer, then log in with Administrator privileges.
Windows® automatically detects the RAID controller and displays a New
Hardware Found window. Click Cancel.
Right-click the My Computer icon on the Windows® desktop , then select
Properties from the menu.
4.
Click the Hardware tab, then click the Device Manager button to display the
list of devices installed in the system.
5.
Right-click the RAID controller item, then select Properties.
6.
Click the Driver tab, then click the Update Driver button.
7.
The Upgrade Device Driver Wizard window appears. Click Next.
8.
Insert the RAID driver disk you created earlier to the floppy disk drive.
9.
Select the option Search for a suitable driver for my device
(recommended), then click Next.
10. The wizard searches the RAID controller drivers. When found, click Next to
install the drivers.
11. Click Finish after the driver installation is done.
6-8
Chapter 6: Driver installation
6.1.3
Red Hat® Enterprise Linux OS
Red Hat® Enterprise Linux OS 4.7/4.8
To install the RAID controller driver when installing��������
Red Hat® Enterprise OS:
1.
Boot the system from the Red Hat® OS installation CD.
2.
At the boot:, type linux dd no�������
storage.
3.
P�������������
ress <Enter>.
- To install or upgrade in graphical mode, press the <ENTER> key.
- To install or upgrade in text mode, type: linux text <ENTER>.
- Use the function keys listed below for more information.
[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]
boot: linux dd nostorage
4.
Select Yes using the <Tab> key when asked if you have the driver disk, then
press <Enter>.
Main Menu
Do you have a driver disk?
Yes
5.
No
Press <Enter> to continue.
Insert Driver Disk
Insert your driver disk into /dev/sda
and press “OK” to continue.
OK
ASUS Z8NH-D12 Series
Cancel
6-9
6.
Select No and press <Enter> to continue.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
7.
No
Select your desired language and press <Enter> to continue.
Choose a Language
What language would you like to use
during the installation process?
Catalan
Chinese(Simplified)
Chinese(Traditional)
Croatian
Czech
Danish
Dutch
English
#
OK
8.
Select your keyboard type and press <Enter> to continue.
Keyboard Type
What type of keyboard do you have?
trq
ua
ua-utf
ua-utf-ws
uk
unicode
us
OK
6-10
#
Back
Chapter 6: Driver installation
9.
Select the media and press <tab> to select OK. Press<Enter> to continue.
Installation Method
What type of media contains the
packages to be installed?
Local CDROM
Hard drive
NFS image
FTP
HTTP
OK
Back
10. Select the media and press <tab> to select OK. Press <Enter> to continue.
No driver found
Unable to find any devices of the type
needed for this installation type.
Would you like to manually select your
driver or use a driver disk?
Select driver
ASUS Z8NH-D12 Series
Use a driver disk
Back
6-11
11. Scroll down to locate the driver and press <Enter> to continue.
Select Device Driver to Load
Please select the driver below which you wish to load. If
it does not appear and you have a driver disk, press F2.
LSI Logic Fusion MPT SPI Driver (mptspi)
LSI MegaRAID Controllers (megaraid_mbox)
LSI MegaRAID Controllers (megaraid_sas)
LSI megasr Driver ver 13.10.0708.2009 (megasr)
Marvell SATA controllers (sata_mv)
Mylex DAC960 RAID Controller (DAC960)
[] Specify optional module arguments
OK
Back
The driver version may vary with time and model. Select LSI Mega Software
RAID driver (LSI megasr Driver) all the time.
12. Select Skip and press <Enter> to continue.
CD Found
To begin testing the CD media before
installation press OK.
Choose Skip to skip the media test
and start the installation.
OK
6-12
Skip
Chapter 6: Driver installation
13. Select Done and press <Enter> to continue.
Devices
The following devices have been found on your system.
Intel Pro/1000 (e1000e)
LSI megasr Driver ver 13.10.0708.2009 (megasr)
USB Mass Storage driver for Linux (usb-storage)
Done
Add Device
The displayed devices may vary with models and systems.
14. Follow the onscreen instructions to finish installing the RedHat operating
system.
ASUS Z8NH-D12 Series
6-13
Red Hat® Enterprise Linux OS 5.0
To install the RAID controller driver when installing��������
Red Hat® Enterprise OS:
1.
Boot the system from the Red Hat® OS installation CD.
2.
At the boot:, type linux dd noprobe=ata[n].�������������������������������
������������������������������
The number of ata varies with
the hard disk drive number you have when building a RAID set. For example, if
you want to build a RAID set with 6 hard disk drives, type command line: linux
dd noprobe=ata1 noprobe=ata2 noprobe=ata3 noprobe=ata4 noprobe=ata5
noprobe=ata6.
3.
P�������������
ress <Enter>.
- To install or upgrade in graphical mode, press the <ENTER> key.
- To install or upgrade in text mode, type: linux text <ENTER>.
- Use the function keys listed below for more information.
[F1-Main] [F2-Options] [F3-General] [F4-Kernel] [F5-Rescue]
boot: linux dd noprobe=ata[n]
4.
Select Yes using the <Tab> key when asked if you have the driver disk, then
press <Enter>.
Main Menu
Do you have a driver disk?
Yes
5.
No
Select fd0 using the <Tab> key when asked to select the driver disk source.
Press <Tab> to move the cursor to OK, then press <Enter>.
Driver Disk Source
You have multiple devices which could
serve as sources for a driver disk.
Which would you like to use?
fd0
scd0
OK
6-14
Cancel
Chapter 6: Driver installation
6.
Insert the Red Hat® Enterprise RAID driver disk to the floppy disk drive, select
OK, then press <Enter>.
Insert Driver Disk
Insert your driver disk into /dev/fd0
and press “OK” to continue.
OK
Back
The drivers for the RAID card are installed to the system.
7.
When asked if you will load additional RAID controller drivers, select No, then
press <Enter>.
More Driver Disks?
Do you wish to load any more
driver disks?
Yes
No
8.
Follow the onscreen instructions to finish the OS installation.
9.
If you install RHEL AS5, when the installation is completed, DO NOT click
Reboot. Press <Ctrl> + <Alt> + <F2> to switch to the command-line interface
from graphic user interface.
10. Type the following commands when using a Legacy floppy.
mkdir /mnt/driver
mount /dev/fd0 /mnt/driver
cd /mnt/driver
sh replace_ahci.sh
reboot
ASUS Z8NH-D12 Series
6-15
Type the following commands when using a USB floppy.
cat /proc/partitions
Write down the Major and Minor number before sdb for later use.
6-16
mknod /dev/sdb b [major number] [minor number]
mkdir /mnt/driver
mount /dev/sdb /mnt/driver
cd /mnt/driver
sh replace_ahci.sh
reboot
Chapter 6: Driver installation
6.1.4
SUSE Linux Enterprise Server OS
To install the RAID controller driver when installing������������������������������
SUSE Linux Enterprise Server
OS:
1.
Boot the system from the SUSE OS installation CD.
2.
Use the arrow keys to select Installation from the Boot Options menu.
Boot from Hard Disk
Installation
Installation--ACPI Disabled
Installation--Local APIC Disabled
Installation--Safe Settings
Rescue System
Memory Test
Boot Options |
F1 Help F2 Language F3 1280 x 1024 F4 DVD F5 Driver
3.
Press <F5>, then select Yes from the menu. Press <Enter>.
Boot from Hard Disk
Installation
Installation--ACPI Disabled
Installation--Local APIC Disabled
Installation--Safe Settings
Rescue System
Memory Test
Yes
No
File
F1 Help F2 Language F3 1280 x 1024 F4 DVD F5 Driver
Boot Options |
ASUS Z8NH-D12 Series
6-17
4.
Insert the RAID driver disk to the floppy disk drive. Make sure that Installation
from the Boot Options menu is selected, then press <Enter>.
Boot from Hard Disk
Installation
Installation--ACPI Disabled
Installation--Local APIC Disabled
Installation--Safe Settings
Rescue System
Memory Test
Boot Options |
F1 Help F2 Language F3 1280 x 1024 F4 DVD F5 Driver
If you install SLES 10, type brokenmodules=ahci after Boot Options and
press Enter to continue.
5.
When below screen appears, select the floppy disk drive (fd0) as the driver
update medium. Select OK, then press <Enter>.
Please choose the Driver Update medium.
fd0: Floppy
sr0: CD-ROM, TEAC DV-516E
sda: Disk, SEAGATE ST336754SS
sdb: Disk, SEAGATE ST336754SS
Other device
OK
6-18
Back
The drivers for the RAID controller are installed to the system.
Chapter 6: Driver installation
6.2
Intel chipset device software
installation
This section provides instructions on how to install the Plug and Play components
for the Intel® chipset on the system.
You need to manually install the Intel® chipset software on a Windows operating
system. To install the Intel® chipset software:
1.
Restart the computer, then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
3.
Click the item Intel Chipset Device Software from the menu.
ASUS Z8NH-D12 Series
6-19
6-20
4.
The Intel(R) Chipset Device Software window appears. Click Next to start
the installation.
5.
Select Yes to accept the terms of the License Agreement and continue the
process.
Chapter 6: Driver installation
6.
Read the Readme File Information and click Next to activate the installation.
7.
After completing the installation, click Next to continue.
ASUS Z8NH-D12 Series
6-21
8.
6-22
Click Yes, I want to restart this computer now and click Finish to restart
the computer.
Chapter 6: Driver installation
6.3
LAN driver installation
This section provides the instructions on how to install Intel® Gigabit LAN controller
drivers.
To install the Intel® Gigabit LAN controller driver on a Windows® OS:
1.
Restart the computer, and then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The DVD
automatically displays the Drivers menu if Autorun is enabled in your
computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file AUTORUN.EXE and double-click the AUTORUN.EXE
and follow step 4 to run the installation.
3.
Click Intel® PRO/1000 Gigabit Adapters Driver.
ASUS Z8NH-D12 Series
6-23
6-24
4.
When the Intel® PRO Network Connections – InstallShield Wizard window
appears, click Next to start the installation.
5.
Click I accept the terms in the license agreement and then click Next to
continue.
Chapter 6: Driver installation
6.
Select the programs you want to install and click Next to continue.
7.
Click Install to start the installation.
ASUS Z8NH-D12 Series
6-25
6-26
8.
The programs you select are being installed.
9.
Click Finish to finish the installation.
Chapter 6: Driver installation
6.4
Display driver installation
This section provides instructions on how to install the ASPEED display driver.
You need to manually install the ASPEED display driver on a Windows® operating
system.
To install the ASPEED display driver
1.
Restart the computer, then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
4.
Click ASPEED AST2050 Display Driver.
4.
When the ASPEED InstallShield Wizard window appears, click Next to
continue.
ASUS Z8NH-D12 Series
6-27
6-28
5.
Click Install to start the installation.
6.
The system installs the driver automatically.
Chapter 6: Driver installation
7.
When the installation completes, click Finish to exit the wizard.
8.
Click Yes to restart the computer.
ASUS Z8NH-D12 Series
6-29
6.5
Mellanox ConnectX DDR and
ConnectX2 QDR PCI Gen2 Channel
Adapter driver installation
This section provides instructions on how to install the Mellanox driver.
6.5.1
Windows operating system
You need to manually install the Mellanox driver on a Windows® operating system.
To install the Mellanox driver
6-30
1.
Restart the computer, then log on with Administrator privileges.
2.
Insert the motherboard/system support DVD to the optical drive. The support
DVD automatically displays the Drivers menu if Autorun is enabled in your
computer.
3.
Click Mellanox ConnectX DDR PCI Gen2 Channel Adapter Driver.
4.
Click Next to start installing the driver.
Chapter 6: Driver installation
5.
Click I accept the terms in the license agreement and click Next to
continue.
5.
Click Change to select your desired destination folder and click Next to
continue.
ASUS Z8NH-D12 Series
6-31
6-32
6.
Select a setup type and click Next to continue.
7.
The driver features you selected are being installed.
Chapter 6: Driver installation
8.
Click your preferred options and click Finish to exit the wizard.
ASUS Z8NH-D12 Series
6-33
6.5.2
Red Hat® Enterprise Linux OS
You need to manually mount the Mellanox driver on a Red Hat® Enterprise Linux
OS.
For users using SUSE Linux Enterprise Server OS, follow the general
instructions in this section to mount the Mellanox driver on your system.
To mount the Mellanox driver
1.
Login to the system as root.
2.
Create a folder on the desktop and copy the latest Mellanox driver to the
folder.
You can name the folder as you like.
3.
Type the command line and mount the driver to the system.
The driver version and the OS label may vary. Ensure that the command line
matches your driver version and operating system.
6-34
Chapter 6: Driver installation
4.
Type the command line and install the driver.
5.
All other Mellanox, OEM, OFED, or distribution IB packages will be removevd.
Press <Y> to continue.
6.
The system starts uninstalling the previous version of OFED.
ASUS Z8NH-D12 Series
6-35
7.
When the installation finishes, reboot your system to complete the installation.
If your system has the latest firmware, no firmware update will occur. To force
firmware update, type --force-fw-update.
6-36
Chapter 6: Driver installation
6.6
Management applications and utilities
installation
The support DVD that came with the motherboard package contains the drivers,
management applications, and utilities that you can install to avail all motherboard
features.
The contents of the support DVD are subject to change at any time without
notice. Visit the ASUS website at www.asus.com for updates.
6.6.1
Running the support DVD
Place the support DVD to the optical drive. The DVD automatically displays the
Drivers menu if Autorun is enabled in your computer.
If Autorun is NOT enabled in your computer, browse the contents of the support
DVD to locate the file ASSETUP.EXE from the BIN folder. Double-click the
ASSETUP.EXE to run the DVD.
6.6.2
Drivers menu
The Drivers menu shows the available device drivers if the system detects installed
devices. Install the necessary drivers to activate the devices.
The screen display and driver options vary under different operating system
versions.
ASUS Z8NH-D12 Series
6-37
6.6.3
Utilities menu
The Utilities menu displays
the software applications and
utilities that the motherboard
supports. Click an item to
install.
6.6.4
Make disk menu
The Make disk menu contains
items to create the Intel Matrix
Storage Manager and LSI
Embedded MegaRAID driver
disk.
6.6.5
Contact information
Click the Contact tab to display
the ASUS contact information.
You can also find this
information on the inside front
cover of this user guide.
6-38
Chapter 6: Driver installation
This appendix includes additional
information that you may refer to when
configuring the motherboard.
A
Reference information
Appendix summary
A
A.1
Z8NH-D12 block diagram..............................................................A-3
A.3
Z8PH-D12 SE/QDR block diagram...............................................A-5
A.2
Z8PH-D12/IFB block diagram.......................................................A-4
ASUS Z8NH-D12 Series
A.1
Z8NH-D12 block diagram
ASUS Z8NH-D12 Series
A-3
A.2
A-4
Z8PH-D12/IFB block diagram
Appendix A: Reference information
A.3
Z8PH-D12 SE/QDR block diagram
ASUS Z8NH-D12 Series
A-5
A-6
Appendix A: Reference information