GV3 Series v8.11 or Higher
Control Panels Quick Reference Guide
en
Quick Reference Guide
GV3 Series v8.11 or Higher
Table of Contents | en
3
Table of Contents
1
GV3 Control Panel Connections (D9412GV3 Shown)
5
2
Upgrade GV3 Hardware and Programming
7
2.1
Receive Existing Control Panel Programming
7
2.1.1
Receive Existing Control Panel Programming with RPS
7
2.2
Upgrade Hardware to a GV3 Series Control Panel
7
2.2.1
Prepare to Remove Existing Hardware
7
2.2.2
Remove the Existing Control Panel
7
2.2.3
Install the GV3 Control Panel In the Enclosure
8
2.2.4
Replace the Terminal Strips
8
2.3
Upgrade Programming to a GV3 Control Panel Programming
9
2.3.1
Upgrade a GV2 Series, G Series, or Non-G Series Control Panel to a GV3 v8.03 or Later Using Remote
Programming Software (RPS) 5.13 or Later9
3
Programming the Control Panel
10
3.1
RPS Programming over a Network Using the DX4020 Ethernet Network Interface Module
10
3.2
RPS Programming over a Network Using the ITS-DX4020-G GPRS/GSM Communicator
10
3.3
RPS Programming Using the DX4010V2 RS-232/USB Serial Interface Module
10
3.4
RPS Programming Using the Keypad Programming
10
4
Programming to Set Up Central Station Reporting
11
4.1
Basic Telephone Set Up in RPS
11
4.2
Basic Internet Protocol (IP)
11
4.3
Account Number
11
5
Programming the Control Panel for Common Reporting Options
12
5.1
Set Up Daily Test Report Using RPS
12
5.2
Set Up Open and Close Reports Using RPS
12
5.2.1
Area Wide Parameters
12
5.2.2
Set Authority Level
12
6
Setting Up Points and Outputs
13
6.1
Using the Relay Option Within Point Assignments
13
6.2
Point Index (Default Values)
14
7
Add System Users Locally With a Keypad
16
7.1
Add Users (CMD 56) Using a Keypad
16
7.2
Add Card (CMD 56) for Access Control Only Using a Keypad
16
8
Turning the System ON or OFF and Keypad Commands
17
8.1
Arming and Disarming the System
17
8.1.1
Master Arming
17
8.1.2
Disarming
17
8.1.3
Set Duress +1 Using RPS
17
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
4
en | Table of Contents
GV3 Series v8.11 or Higher
8.2
Basic and Advanced Commands
17
8.3
SIA CP-01 False Alarm Prevention Options
18
9
Setting DIP Switches
19
9.1
D9127 U/T POPIT Dip Switch Key
19
9.2
D9210B Switch Settings
19
9.3
D720, D1255, D1260 Dip Switch Settings
19
9.4
D9131A Dip Switch Settings
19
9.5
D8129 OctoRelay Dip Switch Settings
19
9.6
D8128C OctoPOPIT Dip Switch Settings
19
9.7
D8128D OctoPOPIT Dip Switch Settings
19
10
Reporting Format Definitions
20
11
Frequently Asked Questions
24
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
1
GV3 Control Panel Connections (D9412GV3 Shown) | en
5
GV3 Control Panel Connections (D9412GV3 Shown)
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
6
en | GV3 Control Panel Connections (D9412GV3 Shown)
F01U170805 | 02 | 2011.10
Quick Reference Guide
GV3 Series v8.11 or Higher
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Upgrade GV3 Hardware and Programming | en
2
Upgrade GV3 Hardware and Programming
2.1
Receive Existing Control Panel Programming
7
NOTICE!
GV3 Series v8.11 and later Control Panels are not compatible with the D5200 Programmer.
2.1.1
Receive Existing Control Panel Programming with RPS
1.
In RPS, double-click on the control panel name.
2.
Click Connect. Once connected, the Panel Sync window opens.
3.
Select the Recieve Panel Data option button and click OK.
2.2
Upgrade Hardware to a GV3 Series Control Panel
2.2.1
Prepare to Remove Existing Hardware
1.
2.
Power down the existing control panel by disconnecting the battery and the AC power.
Remove the four removable terminal strips by tilting the strip up and outward.
Do not remove the wiring from the terminal strip.
1 - Removable terminal strips
2.2.2
Remove the Existing Control Panel
1.
Remove the lock down tab screw.
2.
Lift up on the control panel to free it from the enclosure mounting hooks, and remove the
control panel from the enclosure it.
1 - Lock down tab
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
8
en | Upgrade GV3 Hardware and Programming
2.2.3
GV3 Series v8.11 or Higher
Install the GV3 Control Panel In the Enclosure
1.
Place the GV3 Control Panel in the enclosure using the mounting skirt hook holes on the
back of the control panel and the mounting skirt hooks on the enclosure.
2.
Replace the lock down tab screw.
1 - Mounting skirt hook holes
2 - Mounting skirt hooks
3 - Lock down tab
NOTICE!
If the control panel was previously mounted using the screw hole configuration, the you must
re-mount the new control panel. The GV3 control panel mounting screw hole locations do not
align with the locations for older control panels.
2.2.4
Replace the Terminal Strips
1.
Replace the four removable terminal strips by pushing them straight down until they snap
into position.
2.
F01U170805 | 02 | 2011.10
Connect the battery and AC power.
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
2.3
Upgrade GV3 Hardware and Programming | en
9
Upgrade Programming to a GV3 Control Panel Programming
NOTICE!
You must upgrade G Series and Non-G Series control panels to GV2 programming prior to
upgrading to GV3 programming.
2.3.1
Upgrade a GV2 Series, G Series, or Non-G Series Control Panel to a GV3
v8.03 or Later Using Remote Programming Software (RPS) 5.13 or Later
1.
In RPS, highlight the control panel name by selecting it.
2.
Click the View button on the Remote Programmer Toolbar.
3.
In the resulting Panel Data - View window, click the Edit button.
4.
In the resulting Panel Data - Edit window, select the new control panel type from the
Panel Type drop-down. (If the control panel is a G or Non-G Series control panel, you
must upgrade to GV2 first, and then repeat each of these steps to choose the GV3
control panel.) Click OK to close the window.
5.
Click Save in the Panel View window to save the changes and close the Panel View
window.
6.
Click Connect. Once connected, the Panel Sync window opens.
7.
Select the Send ALL RPS Data to Panel option button and click OK.
8.
Once the sync completes, click Disconnect to disconnect from the control panel.
9.
Exit RPS.
10. Test the control panel for operation.
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
10
3
en | Programming the Control Panel
GV3 Series v8.11 or Higher
Programming the Control Panel
You can program the control panel with RPS using a network connection or serial connection.
You can program some paramaters of the control panel with keypad programming.
3.1
RPS Programming over a Network Using the DX4020 Ethernet
Network Interface Module
For additional information, refer to IP Address Programming in the Conettix DX4020 Network
Interface Module Installation Guide (P/N: F01U045288).
3.2
RPS Programming over a Network Using the ITS-DX4020-G
GPRS/GSM Communicator
For additional information, refer to the Conettix ITS-DX4020-G Installation Guide (P/
N: F01U163066).
3.3
RPS Programming Using the DX4010V2 RS-232/USB Serial
Interface Module
For additional information, refer to the DX4020 RS-232/USB Serial Interface Module Installation
Instructions (P/N: F01U083036).
3.4
RPS Programming Using the Keypad Programming
For additional information, refer to the D9412GV3/D7412GV3 Program Entry Guide (P/N:
F01U170807) or the D7212GV3 Program Entry Guide (P/N: F01U170808).
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
4
Programming to Set Up Central Station Reporting | en
11
Programming to Set Up Central Station Reporting
NOTICE!
You can program these items using RPS and the steps listed below. You can also use keypad
programming with v8.11 and later (refer to the D9412GV3/D7412GV3 Program Entry Guide (P/
N: F01U170807) or the D7212GV3 Program Entry Guide (P/N: F01U170808).
4.1
4.2
Basic Telephone Set Up in RPS
1.
Go to PANEL WIDE PARAMETERS→Phone and Phone Parameters.
2.
Enter the primary telephone number in the Phone 1 field.
3.
If a secondary telephone number is required, enter it in the Phone 2 field.
4.
Go to Panel Wide Parameters→Routing→Route Group 1.
5.
Enter Phone 1 in the Primary field.
6.
If a secondary telephone is required, enter Phone 2 in the Backup field.
Basic Internet Protocol (IP)
1.
Go to PANEL WIDE PARAMETERS→Routing→Route Group 1 Primary.
2.
Enter SDI 88 Path 1 (or SDI 92 Path 1).
3.
Go to AUXPARM→Enhanced Communications.
4.
Select or enter the following values:
NOTICE!
Enhanced Communications settings usually follow the recommendations of the Central
Stations’ staff.
If using an ITS-DX4020-G for communication, refer to the ITS-DX4020-G Installation and
Operation Guide (P/N: F01U163066).
Parameter
Enable Enhanced Communication
Path 1 IP Address
Path 1 Port Number
Path 1 Poll Rate (seconds)1
Path 1 ACK Wait Time
Path 1 Retry Count
Value
YES
IP address of Central Station receiver
Port Number of Central Station receiver
Poll rate recommended by Central Station
13 sec (default setting)
5 (default Setting)
1 If the control panel is programmed to send a heartbeat poll to the central station, a rate of 75 sec
maintains the virtual link in most network configurations.
4.3
Account Number
In RPS, go to AREA WIDE PARAMETERS and enter the account number (up to 10 digits) in
the Account Number parameter.
NOTICE!
Area 1 is the only area turned on by default.
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
12
en | Programming the Control Panel for Common Reporting Options
GV3 Series v8.11 or Higher
5
Programming the Control Panel for Common
Reporting Options
5.1
Set Up Daily Test Report Using RPS
1.
Go to SCHEDULES→Skeds.
2.
Enter Function Code 9 (Test Report) in an unused Sked.
3.
Select NO for the Deferred parameter to send test reports regardless of other test
reports sending between scheduled test reports.
4.
Select NO for the Hourly parameter to send test reports only when the sked executes and
not every hour.
5.
6.
Enter the time at which you wish the schedule to send the report.
Leave the Date parameter disabled so that the sked executes by days of the week instead
of only on a selected date.
7.
8.
Select YES for each day of the week.
Select NO for:
–
Except On Holiday
–
Holidays 1 - 4
5.2
Set Up Open and Close Reports Using RPS
5.2.1
Area Wide Parameters
To report each area independently:
–
Go to AREA WIDE PARAMETERS→Area/Bell,Open/Close Options→Acct Open/Close in
RPS. Select NO (default).
–
Go to Area Open/Close in RPS). Select YES (default).
To report by account (Close signal is sent when the last area in an account is armed; Open
signal is sent when the first area is disarmed):
–
Go to AREA WIDE PARAMETERS→Area/Bell,Open/Close Options→Acct Open/Close
in RPS. Select YES.
–
Go to Area Open/Close in RPS. Select NO.
NOTICE!
If you want Perimeter Open and Close, select Perimeter O/C = YES.
5.2.2
Set Authority Level
1.
Go to USER INTERFACE→Authority Levels.
2.
Go to the Authority Level to be used by users sending Open and Close reports.
3.
Select E (enabled) for Area Open/Close.
4.
Select E for Restricted Open/Close.
5.
Select E for Perimeter Open/Close.
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Setting Up Points and Outputs | en
6
Setting Up Points and Outputs
6.1
Using the Relay Option Within Point Assignments
13
Relay Programming allows any one point or several points to latch a single relay through
software when the selected point generates an alarm. Relays are number 1 through 8 and are
programmed by entering the number of the relay (1 - 8) in the Relay column in Point
Assignments. This relay latches on a generated alarm and resets after acknowledging and then
clearing the alarm from memory.
D8129 Actual Relay Number
Relay
1
2
3
4
5
6
7
8
D7412GV3/D7212GV31
9
10
11
12
13
14
15
16
D9412GV32
73
74
75
76
77
78
79
80
1 For the D7412GV3 and D7212GV3, connect to Terminal 28 for data (Zonex 1 Out).
2 For the D9412GV3, connect to Terminal 26 for data (Zonex 2 Out).
Table 6.1 Actual Relays Latched by Control Panel Type
Switch Number
1
2
3
4
Setting
ON
OFF
ON
ON
Table 6.2 D8129 Switch Settings for All Control Panel Types
NOTICE!
Programmers must be aware of the following considerations:
–
Do not use relays designated within Point Assignments for multiple functions. For
example, Relays 73 through 80 on the D9412GV3 should not be used for relay-followpoint or area-wide or panel-wide relays.
–
Bosch Security Systems, Inc.
Relays should not be selected to follow points programmed as Invisible Points.
Quick Reference Guide
F01U170805 | 02 | 2011.10
14
en | Setting Up Points and Outputs
6.2
GV3 Series v8.11 or Higher
Point Index (Default Values)
Pt Index Description
Pt Index Description
Number
1
24-Hour Instant Audible Alarm on Open or
Number
17
D279 (Non-Priority)
2
3
4
5
Short
Invisible/Silent Hold Up on Short
Fire Pull Station Alarm on Short
Smoke Detector with Reset Alarm on Short
Smoke Detector with Verification Reset and
18
19
20
21
D279 (Priority)
Easikey Input
POPIT Motion Sensor Interior
POPIT Motion Sensor Perimeter
6
7
Alarm on Short
Bell Supervision Trouble on Open/Short
Perimeter Instant Alarm on Open or Short,
22
23
Fire Supervisory on Open, Trouble on Short
Non-Fire Supervisory on Open, Trouble on
8
Watch Point when Disarmed
Perimeter Delay on Short, Instant Alarm on
24
Short
Local, No Visual or Audible Display on Any Fault
9
Short, Watch Point when Disarmed
Perimeter Instant Alarm on Open or Short,
25
Armed or Disarmed with Relay Output
Perimeter Delay on Open, Alarm on Short
10
Local while Disarmed
Interior Instant Alarm on Open or Short
26
24-Hour Instant Audible Alarm on Open or
11
Interior Delay on Short, Alarm on Open
27
Short
24-Hour Instant Audible Alarm on Open or
12
Interior Instant Alarm on Open or Short, Local 28
Short
24-Hour Instant Audible Alarm on Open or
13
while Disarmed
Interior Follower Delay on Short, Alarm on
29
Short
24-Hour Instant Audible Alarm on Open or
14
Open
Maintained Keyswitch
30
Short
24-Hour Instant Audible Alarm on Open or
15
Momentary Keyswitch
31
Short
24-Hour Instant Audible Alarm on Open or
16
Open/Close on Fault
Short
Table 6.3
Point Index Numbers and Descriptions
NOTICE!
The default indexes are not always the best selection.
If you experience unwanted trouble conditions, refer to Table 6.5 on Page 15 and make any
necessary adjustments.
Bosch Commercial Wireless points produce a Short when faulted and an Open for a tamper.
To make a custom Point Index, refer to (Table 6.4 and Table 6.5).
Pt Type Description
0
24-Hour
1
Perimeter
2
Interior
3
Interior Follower
4
Keyswitch
5
Keyswitch Memory
Table 6.4
F01U170805 | 02 | 2011.10
Pt Type
6
7
8
9
11
Description
O/C/ Port
D279 (O/C Non-Priority)
D279 (Priority)
Easikey
AUX AC Supervision
Point Type Selections
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Setting Up Points and Outputs | en
15
NOTICE!
The selections in Table 6.5 indicate:
–
D = Delayed Response
–
I = Instant Alarm
–
S = Supervisory
–
T = Trouble
–
Blank = No Response
To make a custom point index, use Table 6.4 on Page 14 and Table 6.5 on Page 15. For
example, to create an Interior Follower point with a delay on Open and Trouble on Short, use
Point Type 3 and Point Response 5.
Point Response
Selections*
Armed
Open
Short
Disarmed Open
Short
24-Hour
Open
Short
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
I
I
I
I
T
I
I
D
I
D
I
I
D
I
D
T
D
D
I
I
T
I
T
I
T
S
T
I
I
I
T
S
I
I
I
T
I
I
I
I
I
T
S
I
I
T
I
I
I
I
I
T
T
T
T
T
I
T
T
I
T
S
F
I
S
S
N/A
Table 6.5 Point Response Selections
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
16
en | Add System Users Locally With a Keypad
GV3 Series v8.11 or Higher
7
Add System Users Locally With a Keypad
7.1
Add Users (CMD 56) Using a Keypad
Step
1
2
3
4
5
6
7
Table 7.1
7.2
Step
1
2
3
4
5
6
7
Table 7.2
Operator Entry
Enter Command 56
Enter passcode and press [ENT].
Enter the user number and press [ENT].
Enter
Enter
Enter the new user’s passcode.
Re-enter the new passcode.
Keypad Response
Enter Passcode
Enter User #
USER # (default name text)
Change Passcode?
Enter New Code
Enter New Again
Code Changed
Adding Users with Command 56
Add Card (CMD 56) for Access Control Only Using a Keypad
Operator Entry
Command 56
Enter passcode and press [ENT]
Enter the user number and press [ENT]
Enter
Next
Enter
Present the credential to the reader.
Keypad Response
Enter Passcode
Enter User #
USER# (default name text)
Change Passcode?
Add Card?
Present Card
Card Added
Adding Cards with Command 56
NOTICE!
To use Add Card (CMD 56), you must program the Assign Door prompt within Command
Center Assignments with the D9210B door controller number. If you do not program the
Assign Door prompt, the keypad reads 9210 NOT READY.
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Turning the System ON or OFF and Keypad Commands | en
17
8
Turning the System ON or OFF and Keypad Commands
8.1
Arming and Disarming the System
8.1.1
Master Arming
Enter the passcode and [ENTER] to arm all areas where the user has authority and are areas
within the scope of the keypad.
8.1.2
Disarming
Enter the passcode and [ENTER] to disarm all areas where the user has authority and are
areas within the scope of the keypad.
8.1.3
Set Duress +1 Using RPS
1.
Go to PANEL WIDE PARAMETERS→Miscellaneous→Duress Type. Select 1.
2.
Go to AREA WIDE PARAMETERS→Area Parameters→Duress Enable. Select YES.
3.
Go to User Interface→Authority Levels. In the authority levels to be used, select E for
the Send Duress parameter.
8.2
Basic and Advanced Commands
Basic Commands
CMD 1 (Master Arm) [Master Arms only the
area assigned to the Keypad]
CMD 11 (Master Arm Instant)
CMD 3 (Perimeter Delay)
CMD 4 (Silence Trouble Sounder)
CMD 4, 0 (View memory)
CMD 4, 4 (Walk Test)
CMD 4, 7 (Reset Sensors)
CMD 6 (Watch Mode)
CMD 7 (Special Alert)
CMD 8 (Perimeter Partial)
CMD 9 (Special Alert)
CMD 2 Perimeter Instant
Advanced Commands
CMD 0 (Bypass a Point)
CMD 00 (Unbypass a Point)
CMD 41 (Test Report)
CMD 42 (Status Report)
CMD 43 (Remote Program)
CMD 45 (Change Time/Date)
CMD 49 (Change Display)
CMD 50 (Move to Area)
CMD 51 (Extend Closing)
CMD 52 (Change Sked)
CMD 53 (Delete Passcode)
CMD 54 (Change Relay)
CMD 55 (Change Passcode)
CMD 56 (Add Passcode)
CMD 58 (Fire Test)
PRINT LOG (99 [ENTER])
VIEW LOG (99 [ENTER])
Table 8.1 Basic and Advanced Commands
99 Enter Commands
For each of the following commands, press [9] [9] [ENTER]. Press [NEXT] to view each
command.
–
1 - View Log
–
2 - Print Log
–
3 - Display Revision
–
4 - Service Walk
–
5 - Default Text
–
6 - Keypad Programming (Requires Service Passcode)
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
18
8.3
en | Turning the System ON or OFF and Keypad Commands
GV3 Series v8.11 or Higher
SIA CP-01 False Alarm Prevention Options
NOTICE!
Some programming parameters are preset for compliance with SIA standard CP-01 (false
alarm prevention). These settings are in AREA WIDE PARAMETERS→Area Parameters. They
affect control panel operation as described below.
–
Master Arm-No Exit=YES: This setting provides for a Perimeter Delay point to be faulted
when master arming each area, or the arming state defaults to Perimeter Delayed.
–
Exit Delay Warning=YES: When this parameter is set to YES, the alarm bell pulses on and
off every two seconds for the remaining 10 sec of Exit Delay.
–
Entry Delay Warning=YES: When this parameter is set to YES, the alarm bell pulses on
and off every two seconds for the remaining 10 sec of Entry Delay.
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Setting DIP Switches | en
9
Setting DIP Switches
9.1
D9127 U/T POPIT Dip Switch Key
19
POPIT addresses are binary. Refer to Table 9.1:
Switch Number
Binary Value
0
64
1
32
2
16
3
8
4
4
5
2
6
1
Table 9.1 POPIT Dip Switch Keys
To calculate the switch settings for POPITS, you must determine the value to use in the
calculation. For addresses 9 through 127, subtract 9. For addresses 129 through 247,
subtract 129. Use the following procedure with address 48 as the example, substituting the
actual values in your calculation.
1.
Subtract 9 from 48. The result is 39.
2.
Set the switches that add up to 39 to the OFF positions (32 + 4 + 2 + 1 = 39).
SW 1 OFF = 32
SW 4 OFF = 4
SW 5 OFF = 2
SW 6 OFF = 1
9.2
D9210B Switch Settings
For additional information, refer to the Access Control Interface Module D9210B Operation and
Installation Guide (P/N: 32206).
9.3
D720, D1255, D1260 Dip Switch Settings
For additional information, refer to:
9.4
–
D720 Series Keypads Installation Instructions (P/N: 7406918000)
–
D1255/D1255B Keypads Installation Instructions (P/N: 7406819000)
–
D1260/D1260B Keypads Installation Guide (P/N: 48101)
D9131A Dip Switch Settings
For additional information, refer to the Parallel Printer Interface D9131A Installation Guide (P/
N: F01U135506).
9.5
D8129 OctoRelay Dip Switch Settings
For additional information, refer to the D8129 OctoRelay Module Operating and Installation
Guide (P/N: F01U036302).
9.6
D8128C OctoPOPIT Dip Switch Settings
For additional information, refer to the D8128C OctoPOPOIT Module Operating Instructions (P/
N: 7407710000).
9.7
D8128D OctoPOPIT Dip Switch Settings
For additional information, refer to the D8128D OctoPOPOIT Module Installation Guide (P/
N: F01U070537).
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
20
en | Reporting Format Definitions
10
GV3 Series v8.11 or Higher
Reporting Format Definitions
Modem IIIa2 Event
Modem IIIa2 Code
Modem IIIa2 Code Contact ID Event
Contact ID
Bosch SIA Mode
NriaBSppp
Code
A point supervisory
D6500 Mode
Jsppp
24 hour Non-Burglary
condition occurred
A valid local access
RsF01
NLS
Successful Download/Access 1 412 00 000
occurred
A valid remote access
RsssF
NphhhRS
Successful Download/Access 1 412 00 000
callback occurred
A valid remote access
RsssF
NRS
Successful Download/Access 1 412 00 000
occurred
AC Fail – mains power
Pssss
NAT
AC Loss
1 301 00 000
supply
AC Restore – mains
Rsss0
NAR
AC Loss
3 301 00 000
power supply
Access Denied – Door
ADsppp
Nria/idiiiDZppp or Access Denied
Secured
Access Denied –
1 421 aa uuu
Nria/idiii/
ADsppp
ssxDZppp
Nria/idiiiDWppp or Access Denied
Interlocked
Nria/idiii/
Access Denied – No rights ADsppp
ssxDWppp
Nria/idiiiDVppp or Access Denied
in area by card
Nria/idiii/
Access Denied – Unknown ADsppp
ssxDVppp
NriaDDppp
ID
Access Granted
1 150 00 000
AGsppp
1 421 aa uuu
1 421 aa uuu
Access Denied
1 421 aa uuu
Nria/idiiiDGppp or Access Report by User
1 422 aa uuu
Nria/idiii/
ssxDGppp
NriaBAppp
NriaBMppp
Nria/idiiiEAppp
Nria/CRppp
NpidddET
Burglary
Burglary
Entry/Exit
Entry/Exit
Expansion Module Failure
1 130 aa ppp
1 130 aa ppp
1 134 aa ppp
1 459 aa uuu
1 333 00 000
missing, power is shorted
All SDI devices are
RsssD
NpidddER
Expansion Module Failure
3 333 00 000
restored, power is normal
An individual SDI device is TsssD
NpidddEM
Expansion Module Failure
1 333 00 000
missing.
An individual SDI device is RsssD
NpidddEN
Expansion Module Failure
3 333 00 000
restored.
An invalid remote access
TsssF
NphhhRU
Unsuccessful Access
1 413 00 000
callback occurred
An invalid remote access
TsssF
NRU
Unsuccessful Access
1 413 00 000
occurred
Armed perimeter delay
Armed perimeter instant
Bypass by Remote
Bypass by SDI device
Bypass by Sked
Bypass by User
Bypass Point
Csiii
Csiii
Nsppp
Nsppp
Nsppp
Nsppp
Nsppp
Nria/idiiiNL
Nria/idiiiNL
NriaUBppp
Nria/pidddUBppp
Nria/aikkkUBppp
Nria/idiiiUBppp
NriaUBppp
Armed STAY
Armed STAY
Zone/Sensor Bypass
Zone/Sensor Bypass
Zone/Sensor Bypass
Zone/Sensor Bypass
Zone/Sensor Bypass
3 441 aa uuu
3 441 aa uuu
1 570 aa ppp
1 570 aa ppp
1 570 aa ppp
1 570 aa ppp
1 570 aa ppp
Alarm
Alarm Cross Point
Alarm Exit Error
Alarm with Recent Closing
All SDI devices are
F01U170805 | 02 | 2011.10
Asppp
Asppp
Asppp
Asppp
TsssD
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Modem IIIa2 Event
Reporting Format Definitions | en
Modem IIIa2 Code
Modem IIIa2 Code Contact ID Event
Contact ID
Code
Checksum failure on
D6500 Mode
TsD15
Bosch SIA Mode
NYF
RAM Checksum Bad
1 303 00 000
configuration memory
Closing by Area
Closing Early by Area
Closing Late by Area
Communication failure by
Csiii
Csiii
Csiii
TsB01
Nria/idiiiCL
Nria/idiiiCK
Nria/idiiiCJ
NrggYC
O/C by User
Early O/C
Late O/C
Failure to communicate event
3 401 aa uuu
3 451 aa uuu
3 452 aa uuu
1 354 00 000
route group
Communication failure by NsB01
NrggYK
Failure to communicate event 3 354 00 000
route group restored
Communication trouble
TsB01
Nrgg/pidddYS
Communication Trouble
1 350 00 000
by network
Communication trouble
NsB01
Nrgg/pidddYK
CommunicationTrouble
3 350 00 000
by network restored
Communication trouble
TsB01
NphhhYS
Communication Trouble
1 350 00 000
by phone
Communication trouble
NsB01
NphhhYK
Communication Trouble
3 350 00 000
by phone restored
Control panel battery low Tsss9
Control panel battery
Tsss9
NYT
NYM
Low System Battery
Battery Missing/Dead
1 302 00 000
1 311 00 000
missing
Control panel battery
Rsss9
NYR
Low System Battery
3 302 00 000
restored to normal
Create Status Report
Date changed – no user
Sssss
NsD07
NYY
NJD
Status Report to Follow
Time/Date Reset
1 605 00 000
1 625 00 000
identified
Dated changed by user
Door Closed, Restoral
Door Left Open Alarm
Door Left Open Trouble
Duress
Event Log Overflow
Event Log Threshold has
NsD07
Rsppp
Asppp
Tsppp
Dsiii
AsD01
TsD01
NidiiiJD
NriaDHppp
NriaDLppp
NriaDMppp
Nria/idiiiHA
NJO
NJL
Time/Date Reset
Access Door propped open
Access Door propped open
Access Door propped open
Duress
Event Log Overflow
Event Log 90% Full
1 625 00 uuu
1 426 aa ppp
1 426 aa ppp
1 426 aa ppp
1 121 aa uuu
1 624 00 000
1 623 00 000
been reached
Extend Close Time
TsD26
Nria/idiii/
Auto-arm Time Extended
1 464 aa uuu
Extra Point
Fail To Close by Area
Fail To Open by Area
Fire Alarm
Fire Cancel
Fire Missing
Fire Restoral from Alarm
Fire Restoral from Trouble
Fire Supervision
Fire Supervision from
Tsppp
TsssE
TsssE
Fsppp
\siii
Msppp
Hssppp
Hsppp
Esppp
Esppp
tihhmmCE
NriaXEppp
NriaCI
NriaOI
NriaFAppp
Nria/idiiiFC
NriaFYppp
NriaFHppp
NriaFJppp
NriaFSppp
NriaFVppp
Maintenance Alert
Failed to Close
Failed to Open
Fire
Cancel
Fire Trouble
Fire
Fire Trouble
Fire Supervisory
Fire Supervisory
1 393 aa ppp
1 454 aa 000
1 453 aa 000
1 110 aa ppp
1 406 aa ppp
1 373 aa ppp
3 110 aa ppp
3 373 aa ppp
1 200 aa ppp
3 200 aa ppp
Restore
Fire Trouble
Fire Walk Test End
Fire Walk Test Start
Force Armed Perimeter
Gssppp
RsssF
TsssF
Csiii
NriaFTppp
Nria/idiiiFK
Nria/idiiiFI
Nria/idiiiNF
Fire Trouble
Fire Test
Fire Test
Partial Arm
1 373 aa ppp
3 604 aa uuu
1 604 aa uuu
3 456 aa uuu
21
Delay
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
22
en | Reporting Format Definitions
GV3 Series v8.11 or Higher
Modem IIIa2 Event
Modem IIIa2 Code
Modem IIIa2 Code Contact ID Event
Contact ID
Bosch SIA Mode
Nria/idiiiNF
Code
Force Armed Perimeter
D6500 Mode
Csiii
Partial Arm
3 456 aa uuu
Instant
Forced Close Early by
Csiii
Nria/idiiiCF
Early O/C
3 451 aa uuu
Area
Forced Close Late by Area
Forced Closing by Area
Forced Point
Invalid local access
Csiii
Csiii
Tsppp
TsF01
Nria/idiiiCF
Nria/idiiiCF
NriaXWppp
NLU
Late O/C
O/C by user
Zone/Sensor Bypass
Unsuccessful access
3 452 aa uuu
3 401 aa uuu
1 570 aa ppp
1 413 00 000
detected
Low battery on a wireless Tsppp
NriaXTppp
RF Low Battery
1 384 aa ppp
point
Low battery restore on a
Rsppp
NriaXRppp
RF Low Battery
3 384 aa ppp
wireless point
Missing Alarm
Missing Fire Supervision
Missing Supervision
Missing Trouble
Non- Fire Cancel Alarm
Normal start-up of the
Msppp
GMsppp
MTsppp
Vsppp
\siii
NsD14
NriaUZppp
NriaFZppp
NriaBZppp
NriaUYppp
Nria/idiiiBC
NRR
General Alarm
Fire Trouble
Loss of Supervision - RPM
Loss of Supervision - RPM
Cancel
System Reset
1 140 aa ppp
1 200 aa ppp
1 382 aa ppp
1 382 aa ppp
1 406 aa ppp
1 305 00 000
control panel
Opening by Area
Opening Early by Area
Opening Late by Area
Parameters changed by
Osiii
Osiii
Osiii
NsD02
Nria/idiiiOP
Nria/idiiiOK
Nria/idiiiOJ
NYG
O/C by user
Early O/C
Late O/C
Panel Programming Changed
1 401 aa uuu
1 451 aa uuu
1 452 aa uuu
1 306 00 000
RPS
Phone Line Missing (1 or TsssB
NLT1 or NLT2
Telco 1 Fault
1 351 00 000
2)
Phone Line Restored (1 or RsssB
NLR1 or NLR2
Telco 1 Fault
3 3515 00 000
2)
Point Bus Fail
TsssD
Point Bus Restoral, power RsssD
NET
NER
Protection Loop
Protection Loop
1 370 00 000
3 370 00 000
normal or bus not missing
RAM Fail with RPS
TsF02
Relay Reset by
NsD22
NRA
NpidddROrrr
Unsuccessful access
Sounder/Relay
1 413 00 000
3 320 00 000
Programmer
Relay Reset by Remote
Relay Reset by Sked
Relay Reset by User
Relay Set by Programmer
Relay Set by Remote
Relay Set by Sked
Relay Set by User
Remote Reset – System
NsD24
NsD20
NsD18
NsD21
NsD23
NsD19
NsD28
NsD11
NROrrr
NaikkkROrrr
NidiiiROrrr
NpidddRCrrr
NRCrrr
NaikkkRCrrr
NidiiiRCrrr
NRN
Sounder/Relay
Sounder/Relay
Sounder/Relay
Sounder/Relay
Sounder/Relay
Sounder/Relay
Sounder/Relay
System Reset
3 320 00 000
3 320 00 000
3 320 00 000
1 320 00 000
1 320 00 000
1 320 00 000
1 320 00 000
1 305 00 000
was reset by RPS
Restoral
Restoral from Alarm
Restoral from Ground
Rsppp
Rsppp
Rsppp
NriaBRppp
NriaBHppp
NriaBRppp
Sensor Trouble
Burglary
Ground Fault
3 380 aa ppp
3 130 aa ppp
3 310 aa ppp
Fault
ROM Checksum Fail (Not AsD12
NYX
ROM Checksum bad
1 304 00 000
Used)
Sensor Reset
Service Walk Test End
Nria/idiiiXIrrr
NidiiiTE
Sounder/Relay
Service On/Off Premises
3 320 00 000
3 466 aa uuu
F01U170805 | 02 | 2011.10
NsD27
RsssF
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Reporting Format Definitions | en
Modem IIIa2 Code Contact ID Event
Contact ID
D6500 Mode
Service Walk Test Start
TsssF
Sked Changed – No User NsD06
Bosch SIA Mode
Nria/idiiiTS
NaikkkJS
Code
Service On/Off Premises
Schedule Change
1 466 aa uuu
1 630 00 000
Identified
Sked Changed by User
Sked Changed Remotely
Swinger Bypass
Test Report – System
Nidiii/aikkkJS
Nid255/aikkkJS
NriaUBppp
NRP & see D6600
Schedule Change
Schedule Change
Swinger Bypass
Periodic Test Report
1 630 00 000
1 630 00 000
1 575 aa ppp
1 602 00 000
Items
NRP
Periodic Test Report
1 602 00 000
Status
Test Report – System Off- RsssE
NRY & see D6600
Periodic Test – System
1 608 00 000
normal, Expanded Status
CIM for Status
Trouble Present
Test Report – System Off- RsssE
Items
NRY
Modem IIIa2 Event
Modem IIIa2 Code
NsD06
NsD06
Nsppp
RsssE
Normal, Expanded Status
Test Report – System
23
CIM for Status
RsssE
Normal, Non-expanded
Periodic Test – System
1 608 00 000
Trouble Present
normal, Non-expanded
Status
Time Changed – No User
NsD07
NJT
Time/Date Reset
1 625 00 000
Identified
Time Changed by
NsD07
Nid254JT
Time/Date Reset
1 625 00 254
Receiver Sync
Time Changed by User
Trouble
Trouble with Ground Fault
Unverified Event
User Alarm 7
User Alarm 9
User Passcode Tamper –
NsD07
Tsppp
Tsppp
Ksppp
Usss7
UUsss9
NsD03
NidiiiJT
NriaBTppp
NriaBTppp
NriaUGppp
Nria/idiiiUA
Nria/idiiiPA
NriaJA
Time/Date Reset
Sensor Trouble
Ground Fault
Cross-zone Trouble
Personal Emergency
Duress
Wrong Code Entry
1 625 00 uuu
1 380 aa ppp
1 310 aa ppp
1 378 aa ppp
1 101 aa uuu
1 121 aa uuu
1 461 aa 000
Too Many Attempts
Walk Test End
Walk Test Start
Watchdog Reset – SDI
RsssF
TsssF
NsD09
Nria/idiiiTE
Nria/idiiiTS
NpidddYW
Walk test mode
Walk test mode
System Reset
3 607 aa uuu
1 607 aa uuu
1 305 00 000
Device Reported
identifies the Source
Table 10.1
Reporting Format Definitions
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
24
11
en | Frequently Asked Questions
GV3 Series v8.11 or Higher
Frequently Asked Questions
What does it mean when my keypad reads "CALL FOR SERVICE"?
That keypad is not receiving data from the control panel.
What does it mean when my keypad reads "SERVICE KEYPAD"?
A supervised keypad has lost communications with the control panel.
How do I arm an area that is not assigned to my keypad?
Add to the FUNCTION LIST a menu item with a function code of 1 and with CC ADDRESS 1-16
set to YES, and a menu item with a function code of 2 and with CC ADDRESS 1-16 set to Yes.
Assign the function codes to the necessary command center. The new menu items allow your
users to select the area they wish to arm or disarm.
How do I perform area-specific functions from a keypad?
Use the MOVE TO AREA command (CMD 50) to move to an area within the keypad’s scope.
Can I default a lockcode without knowing the lockcode?
No. You must send the unit to the Bosch Repair Center.
How do I upgrade the control panel version?
Use the supplied firmware upgrade key to upgrade the firmware. Lift the control panel
faceplate cover to access the port to insert the upgrade key and read the instructions located
on the back of the faceplate.
How do I add an access card using the command center?
Use the ADD USER command (CMD 56) to add an access card. Present the access card to the
assigned door to add the card.
What does it mean when my keypad reads "9210 NOT READY"?
No door is assigned to the command center. Check the ASSIGN DOOR parameter within
COMMAND CENTER ASSIGNMENTS menu item, and then enter the D9210B address (1 - 8).
What are SDI addresses 33 to 40?
They are D9210B addresses.
What are SKEDS 41 to 56?
They are Open and Close windows.
How do I test a relay from the keypad?
Use the RELAY CONTROL command (CMD 54) to toggle relays.
How do I toggle the on-board relays A, B, and C?
Use the RELAY CONTROL command (CMD 54), and then the relay number: 253 for A; 254 for
B; and 255 for C.
How many Amp Hours can the panel sustain?
You can connect two (2) 18 Ah batteries for a total of 36 Ah. You can gain up to an additional
27 Ah with by connecting a D8132 module.
Is the control panel compatible with digital or VOIP phone lines?
The control panel has been tested with only analogue lines. Use a DX4020 to transmit over
Ethernet or a ITS-DX4020-G to transmit over cellular. You can use a C900V2 to convert
analogue signals to Ethernet for transmission to a D6600 receiver.
How do I silence a trouble condition?
Use the SILENCE TROUBLE SOUNDER command (CMD 4) to silence a trouble condition.
F01U170805 | 02 | 2011.10
Quick Reference Guide
Bosch Security Systems, Inc.
GV3 Series v8.11 or Higher
Frequently Asked Questions | en
25
How do I clear alarm memory?
Ensure all points are normal, and the enter your passcode and press [ESC], or press the
[Clear] soft key.
How do I determine if I have a ground fault?
On the control panel, measure voltage on terminal 9 (common) and terminal 10 (earth
ground). Approximately 6.5 to 6.8 VDC is normal voltage and equals no ground fault.
Disconnect wires until you see normal voltage to find your ground.
Can I add wireless capability to this control panel?
Yes. Use the Bosch Commercial Wireless Kit (ISW-CWKIT-01) and the proper Bosch
Commercial Wireless transmitters to fully integrate wireless on the control panel.
What type of cable do I use to connect my computer’s COM port to a serial-enhanced direct
connection using the DX4010i?
A null modem cable is required.
How can I determine which points are not ready when my keypad reads "NOT READY TO
ARM"?
Press the NEXT key to scroll through faulted points. If the VIEW POINT STATUS menu item is
enabled, you can access it through the menu to determine the state of the faulted point.
What does it mean when my keypad reads "CHECK DEVICE"?
A point is faulted. The point is one that is configured to display as a device in the POINT INDEX
by marking YES for the DISPLAY AS DEVICE parameter.
I hear a trouble tone from my keypad but no point is shown as in trouble on the keypad.
How do I resolve this?
A point generates a trouble tone (buzz) when faulted if is configured to do so. To determine
which points are configured to buzz, look in the POINT INDEX for points with a non-zero value
for the BUZZ ON FAULT parameter.
How can I determine the meaning of an undefined signal received from central station?
Press 99 [ENTER] on the keypad to reveal the VIEW LOG menu item. Locate the signal in the
log by date and time.
Which reporting formats can the panel send?
Modem IIIa2 or Contact ID. BFSK was replaced with Contact ID for the GV3 control panel.
What is the default Installer Code?
The code is 123.
What is the default User Code?
The code is 123456.
What is the default RPS Passcode?
The code is 999999.
Is the GV3 control panel keypad programmable?
Yes. RPS version 5.13 or later allows you to program all parameters of your GV3 control panel.
Keypad Programming, accessed with 99 [ENTER], allows you to program many parameters of
your GV3 control panel, for example, the RPS passcode. Refer to Section 3.4 RPS Programming
Using the Keypad Programming, page 10.
Where can I find free documentation and on-line support for this product?
Go to www.boschsecurity.us.
Bosch Security Systems, Inc.
Quick Reference Guide
F01U170805 | 02 | 2011.10
Bosch Security Systems, Inc.
130 Perinton Parkway
Fairport, NY 14450
USA
www.boschsecurity.com
© Bosch Security Systems, Inc., 2011