Vivotek 4X-IP7131 User`s manual

3GPP
IP7131
IP Sur veillance
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Product Name:
Network Camera (IP7131)
Product Date:
name:
Release
Network Camera (IP7131)
2009/05/13
Release Date:
2007/11/10
2007/06/05
Manual Revision:
2.2
Web
Site:
Web site:
www.vivotek.com
www.vivotek.com
Email:
Email:
technical@vivotek.com
technical@vivotek.com
Manual Revision:
1.2
2.0
sales@vivotek.com
sales@vivotek.com
Made in
in Taiwan.
Taiwan.
Made
©Copyright
2007-2012.
© 2007-2009
VIVOTEK
INC.All
Allrights
rightsreserved
reserved
-1-
1 - User's Manual
www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Before You Use This Product
The use of surveillance devices may be prohibited by law in your country. The
Network Camera is not only a high-performance web-ready camera but also can be
part of a flexible surveillance system. It is the user’s responsibility to ensure that the
operation of such devices is legal before installing this unit for its intended use.
It is important to first verify that all contents received are complete according to the
list in the "Package Contents" chapter. Take notice of the warnings in “Quick
installation guide” before the Network Camera is installed, then carefully read and
follow the instructions in the “Installation” chapter to avoid damages due to faulty
assembly and installation.
This also ensures the product is used properly as
intended.
The Network Camera is a network device and its use should be straightforward for
those who have basic network knowledge. The “Troubleshooting” chapter in the
Appendix provides remedies to the most common errors in set up and configuration.
You should consult this chapter first if you run into a system error.
The Network Camera is designed for various applications including video sharing,
general security/surveillance, etc.
The “How to Use” chapter suggests ways to best
utilize the Network Camera and ensure proper operations. For the creative and
professional developers, the "URL Commands of The Network Camera " chapter
serves to be a helpful reference to customize existing homepages or integrating with
the current web server.
For paragraphs preceded by
completely the warnings.
the reader should use caution to understand
Ignoring the warnings may result in serious hazards or
injuries.
-2www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
User's Manual - 2
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Table of Contents
Before You Use This Product......................................................................2
Package Contents ....................................................................................6
Installation .............................................................................................7
Hardware installation..........................................................................7
Software installation...........................................................................8
Initial Access to the Network Camera ....................................................9
Check Network Settings ................................................................9
Add Password to prevent Unauthorized Access..................................9
How to Use ..................................................................................... 10
Authentication............................................................................ 10
Installing plug-in.............................................................................. 11
Primary user’s capability ................................................................... 12
Main Screen with Camera View ..................................................... 12
Digital Zoom .............................................................................. 13
Snapshot................................................................................... 13
Client settings ............................................................................ 14
Administrator’s capability .................................................................. 17
Fine-tuning for Best Performance .................................................. 17
Opening accounts for new users ................................................... 20
Build a security application .......................................................... 21
Software revision upgrade ........................................................... 22
Definitions in Configuration ..................................................................... 23
System parameters .......................................................................... 25
Security settings .............................................................................. 26
Network settings.............................................................................. 27
Network type ............................................................................. 27
HTTP ........................................................................................ 28
RTSP Streaming ......................................................................... 28
DDNS............................................................................................. 30
Access List ...................................................................................... 31
Audio and Video............................................................................... 32
-3-
3 - User's Manual
www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
General ..................................................................................... 32
Video Settings............................................................................ 32
Video orientation ........................................................................ 32
Audio settings ............................................................................ 33
Image Settings .......................................................................... 34
Email & FTP .................................................................................... 35
Email ........................................................................................ 35
FTP .......................................................................................... 35
Motion detection .............................................................................. 37
Application settings .......................................................................... 38
Snapshot................................................................................... 38
Weekly schedule......................................................................... 39
Snapshot file name prefix ............................................................ 39
Send out the snapshot while motion detection ................................ 39
Sequential operation ................................................................... 40
Method for sending snapshot........................................................ 40
System log...................................................................................... 47
Viewing system parameters............................................................... 48
Maintenance.................................................................................... 49
Appendix.............................................................................................. 50
A. Troubleshooting ........................................................................... 50
Status LED ................................................................................ 50
Reset and restore ....................................................................... 50
B. URL commands of the Network Camera ........................................... 51
Get server parameter values ........................................................ 51
Set server parameter values ........................................................ 52
Available parameters on the server ............................................... 54
Application page CGI command .................................................... 64
Capture single snapshot .............................................................. 65
Account management ................................................................. 66
System logs............................................................................... 67
Configuration file ........................................................................ 68
Upgrade firmware ....................................................................... 68
-4www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
User's Manual - 4
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
D. Technical specifications ................................................................. 70
C.
-5-
5 - User's Manual
www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Package Contents
IP7131
Software CD
Power adapter
Quick installation guide
Camera stand
Warranty card
-6www.vivotek.com
T: 886-2-82455282
F: 886-2-82455532
User's Manual - 6
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Installation
In this manual, "User" refers to whoever has access to the Network Camera, and
"Administrator" refers to the person who can configure the Network Camera and grant
user access to the camera.
Hardware installation
Please verify that your product package contains all the
accessories listed in the foregoing Package Contents.
Depending on the user’s application, an Ethernet cable
may be needed. The Ethernet cable should meet the specs
of UTP Category 5 and not exceed 100 meters in length.
Connect the power adapter jack to the Network
Camera before plugging in to the power socket. This will
reduce the risk of accidental electric shock.
Upon powering up, the front blue LED will become lighted first and then the device will go
Status LED Color
Description
through booting process. During the booting process, both blue and red LEDs will be on
Blinking red
Power is being supplied to the camera.
Solid green
The camera is booting up.
and the Network Camera will standby for getting IP address. After getting IP Address, the
LED
blink
blue
everyred
second.
Solidwill
green
with
blinking
in between
The camera is trying to obtain an IP address.
An IP address is successfully assigned to the
Solid green and red
camera.
The Network Camera will first detect Ethernet. During the process, the red LED of the
Solid red with blinking green in between The camera is working.
Network Camera will flash every second. Operating in either network mode, the blue LED
Blinking red and green
During firmware upgrading
will flash every second as heartbeat to indicate alive.
To install in Ethernet
Make sure the Ethernet is firmly connected to a switch hub. After attaching the
To install in Ethernet
Ethernet cable plug in the power adapter. When the red LED is lighted and the green
Make sure the Ethernet is firmly connected to a switch hub. After attaching the Ethernet
LED blinks every other second in between, indicating the camera is working, please
cable plug in the power adapter. If the LED turns out to be steady blue, go to next
go to next paragraph “Software installation”. If the Ethernet is not available, Network
paragraph “Software installation”. If the Ethernet is not available, Network Camera will
Camera will switch to wireless LAN mode.
-7www.vivotek.com
7 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
switch to wireless LAN mode.
This Network Camera provides a general I/O terminal block with one digital input and one
digital output device control. The pin definition is as below.
Software installation
At the end of the hardware installation, users can use Installation Wizard program
included in the product CDROM to find the location of the Network Camera. There may be
many Network Cameras in the local network. Users can differentiate the Network
Cameras with the serial number. The serial number is printed on the labels on the carton
and the back of the Network Camera body. Please refer to the user’s manual of
Installation Wizard for detail.
-8www.vivotek.com
User's Manual - 8
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Once installation is complete, the Administrator should proceed to the next
section "Initial access to the Network Camera" for necessary checks and
configurations.
Initial Access to the Network Camera
Check Network Settings
The Network Camera can be connected either before or immediately after software
installation onto the Local Area Network. The Administrator should complete the
network settings on the configuration page, including the correct subnet mask and IP
address of gateway and DNS. Ask your network administrator or Internet service
provider for the detail information. By default the Network Camera requires the
Administrator to run installation every time it reboots. If the network settings are to
remain unchanged, disable the Install option. Refer to “Network settings” on the
System Configuration page for details. If any setting is entered incorrectly and cannot
proceed to setting up the Network Camera, restore the factory settings following the
steps in the “Troubleshooting” chapter of the Appendix.
Add Password to prevent Unauthorized Access
The default Administrator’s password is blank and the Network Camera initially will not
ask for any password. The Administrator should immediately implement a new
password as a matter of prudent security practice. Once the Administrator’s password
is saved, the Network Camera will ask for the user’s name and password before each
access. The Administrator can set up a maximum of twenty (20) user accounts. Each
user can access the Network Camera except to perform system configuration. Some
critical functions are exclusive for the Administrator, such as system configuration, user
administration, and software upgrades. The user name for the Administrator is
permanently assigned as “root”. Once the password is changed, the browser will
display an authentication window to ask for the new password.
Once the password
is set, there is no provision to recover the Administrator’s password.
The
-9www.vivotek.com
9 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
only option is to restore to the original factory default settings.
How to Use
Authentication
After opening the Web browser and typing in the URL of the Network Camera, a
dialogue window pops up to request a username and password. Upon successful
authentication, the following figure is displayed.
The foreground is the login window and the background shows the message if
authentication fails. The user may check the option box to save the password for future
convenience.
This option is not available to the Administrator for obvious reason.
- 10 www.vivotek.com
User's Manual - 10
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Installing plug-in
For the initial access to the Network Camera in Windows, the web browser may prompt
for permission to install a new plug-in for the Network Camera. Permission request
depends on the Internet security settings of the user’s PC or notebook. If the highest
security level is set, the computer may prohibit any installation and execution attempt.
This plug-in has been registered for certificate and is used to display the video in the
browser. Users may click on
to proceed. If the web browser does not allow the
user to continue to install, check the Internet security option and lower the security
levels or contact your IT or networking supervisor for help.
- 11 www.vivotek.com
11 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Primary user’s capability
Main Screen with Camera View
The main page layout has two parts:
Configuration functions: The camera can be configured using these user interfaces.
Camera View: What the camera sees.
Click on the configuration link to the left of the image window to enter the configuration
page.
- 12 www.vivotek.com
User's Manual - 12
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Digital Zoom
Click on the magnifier icon under the camera view then the digital zoom control panel
will be shown. Uncheck “Disable digital zoom” and use the slider control to change the
zoom factors.
1
2
3
Snapshot
Click on “Snapshot”, web browser will pop up a new window to show the snapshot.
Users can point at the snapshot and click the right button of mouse to save it.
- 13 www.vivotek.com
13 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Client settings
At the initial access to the “Connection type” page in Windows, the web browser will ask
for a new plug-in installation, the plug-in being the Network Camera. This plug-in has
been registered for certification and can be used to change the parameters at the
client’s site. The user may click on
to install the plug-in. If the web browser
does not allow the user to complete the installation, check the Internet security to
lower the security level or contact your IT or networking supervisor.
- 14 www.vivotek.com
User's Manual - 14
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
There are two settings for the client side. One is “Media Options” for users to
determine the type of media to be streaming. The other is “Protocol Options” which
allows choices on connection protocol between client and server. There are two
protocols choices to optimize your usage – UDP and TCP.
The UDP protocol allows for more real-time audio and video streams. However, some
packets may be lost due to network burst traffic and images may be obscured.
The TCP protocol allows for less packet loss and produces a more accurate video
display. The downside with this protocol is that the real-time effect is worse than that
with the UDP protocol.
If no special need is required, UDP protocol is recommended. Generally speaking, the
client’s choice will be in the order of UDP → TCP.
After the Network Camera is
connected successfully, “Protocol Option” will indicate the selected protocol. The
selected protocol will be recorded in the user's PC and will be used for the next
connection. If the network environment is changed, or the user wants to let the web
browser to detect again, manually select the UDP protocol, save, and return HOME to
- 15 www.vivotek.com
15 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
re-connect.
<url> http://<Network Camera>/client.html
<Network Camera> is the domain name or the original IP address of the Network
Camera.
Digital output
Click on “ON”, the digital output of the Network Camera will be triggered. Or, Clicking
on “OFF” can let the digital output turn into normal state.
- 16 www.vivotek.com
User's Manual - 16
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Administrator’s capability
Fine-tuning for Best Performance
Best performance generally equates to the fastest image refresh rate with the best
video quality, and at the lowest network bandwidth as possible. The three factors,
“Maximum frame rate”, “Constant bit rate”, and “Fix quality” on the Audio and Video
Configuration page, are correlative to allow for achieving the best performance
possible.
- 17 www.vivotek.com
17 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
For Viewing by Mobile Phone
Most 3GPP cell phone supports media streaming with MPEG4 video and GSM-AMR
audio. Due to the limitation of the bandwidth for 3GPP, only 176x144 video solution will
be supported for cell phone viewing. Select the “Configure for mobile viewing” option
will change the range of other related video settings.
For Best Real-time Video Images
To achieve good real-time visual effect, the network bandwidth should be large enough
to allow a transmission rate of greater than 20 image frames per second. If the
broadband network is over 1 Mbps, set the “Fix bit rate” to 1000Kbps or 1200Kbps, and
set “Fix quality” at the highest quality. The maximum frame rate is 30. If your network
bandwidth is more than 512Kbps, you can fix the bit rate according to your bandwidth
and set the maximum frame rate to 30 fps. If the images vary dramatically in your
environment, you may want to slow the maximum frame rate down to 20 fps in order
to lower the rate of data transmission. This allows for better video quality and the
human eyes cannot readily detect the differences between those of 20, 25, or 30
frames per second. If your network bandwidth is below 512 Kbps, set the “Fix bit rate”
according to your bandwidth and try to get the best performance by fine-tuning with
the “Maximum frame rate”. In a slow network, greater frame rate results in blur images.
Another work-around is to choose “160x120” in the “Size” option for better images.
Video quality performance will vary somewhat due to the number of users viewing on
the network; even when the parameters have initially been finely tuned.
Performance
will also suffer due to poor connectivity because of the network’s burst constraint.
Only Quality Images Will Do
To have the best video quality, you should set “Fix quality” at “Detailed” or “Excellent”
and adjust the “Maximum frame rate” to match your network’s bandwidth. If your
network is slow and you receive “broken” pictures, go to the TCP protocol in
“Connection type” and choose a more appropriate mode of transmission. The images
may suffer a time delay due to a slower connection.
The delay will also increase with
added number of users.
- 18 www.vivotek.com
User's Manual - 18
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Somewhere Between Real-time and Clear Images
If you have a broadband network, set “Fix quality” at ”Normal” or better, rather than
setting “Fix bit rate”. You can also fix the bandwidth according to your actual network
speed and adjust the frame rate.
15 fps.
Start from 30 fps down for best results but not below
If the image qualities are not improved, select a lower bandwidth setting.
- 19 www.vivotek.com
19 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Opening accounts for new users
1
2
3
Protect Network Camera by passwords
The Network Camera is shipped without any password by default. That means
everyone can access the Network Camera including the configuration as long as the IP
address is known. It is necessary to assign a password if the Network Camera is
1 to enable protection.
intended to be accessed by others. Type a new word twice in ○
This password is used to identify the administrator. Then add an account with user
2 . Network Camera can provide twenty
name and password for your friends in ○
3 .
accounts for your valuable customers or friends. You may delete some users from ○
- 20 www.vivotek.com
User's Manual - 20
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Build a security application
The Administrator can use the built-in motion detection to monitor any movement to
perform many useful security applications. To upload the snapshots, users can choose
either email or FTP according to user’s needs. Both e-mail and FTP use the network
settings on the Email and FTP page. Refer to the definition section for detail
configuration.
1. Click on “Configuration” on homepage,
2. Click on “Motion detection” at the left column,
3. Check “Enable motion detection”,
4. Click on new to have a new window to monitor video,
5. Type in a name to identify the new window,
6. Use the mouse to click, hold, and drag the window corner to resize or the title bar to
move,
7. Fine-tune using the “Sensitivity” and “Percentage” fields to best suit the camera’s
environment. Higher ”Sensitivity” detects the slighter motion. Higher “Percentage”
discriminates smaller objects,
8. Clicking on “Save” enables the activity display. Green means the motion in the
window is under the watermark set by Administrator and red means it is over the
watermark,
9. Click on “Application” at the left column,
10.Check the weekdays as you need and give the time interval to monitor the motion
detection every day,
11.Select the Trigger on Motion detection.
12.Set the delay before detecting next motion to avoid continuous false alarms
following the original event,
13.Set the number of pre-event and post-event images to be uploaded,
14.Check the window name set in step 5,
15.Check the way to upload snapshot,
Click on save to validate.
- 21 www.vivotek.com
21 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Software revision upgrade
Customers can obtain the up-to-date software from the web site of Vivotek. An
easy-to-use Upgrade Wizard is provided to upgrade the Network Camera with just a
few clicks. The upgrade function is opened to the Administrator only. To upgrade the
system, follow the procedures below.
1. Download the firmware file named “xxx.pkg” from the appropriate product folder.
2. Run the Upgrade Wizard and proceed following the prompts. Refer to the
instructions of the Upgrade Wizard for details.
3. Or upgrade firmware from HTTP web page directly
3. The whole process will finish in a few minutes and it will automatically restart the
system.
If power fails during the writing process of Flash memory, the program in the
memory of the Network Camera may be destroyed permanently. If the Network
Camera cannot restart properly, ask your dealer for technical service.
- 22 www.vivotek.com
User's Manual - 22
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Definitions in Configuration
Only the Administrator can access system configuration. Each category in the left
column will be explained in the following pages. The bold texts are the specific phrases
on the Option pages. The Administrator may type the URL below the figure to directly
enter the frame page of configuration. If the Administrator also wants to set certain
options through the URL, read the reference appendix for details.
<url> http://<Network Camera>/setup/config.html
- 23 www.vivotek.com
23 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
<Network Camera> is the domain name or original IP address of the Network Camera.
<url> http://<Network Camera>/setup/system.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 24 www.vivotek.com
User's Manual - 24
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
System parameters
"Host name" The text displays the title at the top of the main page.
“Turn off the LED indicator” Check this option to shut off the LED on the rear. It can
prevent the camera’s operation being noticed.
"Keep current date and time" Click on this to reserve the current date and time of
the Network Camera. An internal real-time clock maintains the date and time even
when the power of the system is turned off.
"Sync with computer time" Synchronizes the date and time of the Network Camera
with the local computer. The read-only date and time of the PC is displayed as updated.
“Manual” Adjust the date and time according to what is entered by the Administrator.
Notice the format in the related fields while doing the entry.
“Automatic” Synchronize with the NTP server over the Internet whenever the
Network Camera starts up. It will fail if the assigned time-server cannot be reached.
“NTP server” Assign the IP address or domain name of the time-server. Leaving the
text box blank connects the Network Camera to the default time-servers.
"Time zone" Adjust the time with that of the time-servers for local settings.
“Update interval” Select hourly, daily, weekly, or monthly update with the time on the
NTP server.
“Digital input” Select High or Low to define normal status of the digital input.
“Digital output” Select Grounded or Open to define normal status of the digital
output .
“Reset digital output” The check box enable the function of resetting digital output.
When the digital output is triggered, after the number time the digital output will
reset into normal state.
Remember to click on
to immediately validate the changes. Otherwise, the
correct time will not be synchronized.
- 25 www.vivotek.com
25 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Security settings
“Root password” Change the Administrator’s password by typing in the new
password identically in both text boxes. The typed entries will be displayed as asterisks
for security purposes. After pressing
, the web browser will ask the Administrator
for the new password for access.
“Add user” Type the new user's name and password and press
to insert the new
entry. The new user will be displayed in the user name list. There is a maximum of
twenty user accounts. Checking I/O access can enable user to use D/I and D/O
applications
“Manager user” Pull down the user list to find the user’s name and press
to
complete.
<url> http://<Network Camera>/setup/security.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 26 www.vivotek.com
User's Manual - 26
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Network settings
Any changes made on this page will restart the system in order to validate the changes.
Make sure every field is entered correctly before clicking on
.
Network type
“LAN” & “PPPoE”
The default type is LAN. Select PPPoE if using ADSL
"Get IP address automatically" & “Use fixed IP address”
The default status is “Get IP address automatically”. This can be tedious having to
perform software installation whenever the Network Camera starts. Therefore, once
the network settings, especially the IP address, have been entered correctly, select
“Use fixed IP address” then the Network Camera will skip installation at the next
boot. The Network Camera can automatically restart and operate normally after a
power outage. Users can run IP installer to check the IP address assigned to the
Network Camera if the IP address is forgotten or using the UPnP function provided by
the Network Camera (MS Windows XP provides UPnP function at My Network Place).
“IP address” This is necessary for network identification.
“Subnet mask” This is used to determine if the destination is in the same subnet. The
default value is “255.255.255.0”.
“Default router” This is the gateway used to forward frames to destinations in a
different subnet. Invalid router setting will fail the transmission to destinations in
different subnet.
“Primary DNS” The primary domain name server that translates hostnames into IP
addresses.
“Secondary DNS” Secondary domain name server that backups the Primary DNS.
“Enable UPnP presentation” Enable the UPnP camera short cut
“Enable UPnP port forwarding” Enable uPnP port forwarding
“PPPoE” If using the PPPoE interface , fill the following settings from ISP
“User name” The login name of PPPoE account
- 27 www.vivotek.com
27 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
“Password” The password of PPPoE account
“Confirm password” Input password again for confirmation
HTTP
“Http port” This can be other than the default Port 80. Once the port is changed, the
users must be notified the change for the connection to be successful. For instance,
when the Administrator changes the HTTP port of the Network Camera whose IP
address is 192.168.0.100 from 80 to 8080, the users must type in the web browser
“http://192.168.0.100:8080” instead of “http://192.168.0.100”.
RTSP Streaming
“Access name” This is the access URL for making connection from client software.
Using rtsp://<ip address>/<access name> to make connection
“RTSP port” This can be other than the default Port 554
- 28 www.vivotek.com
User's Manual - 28
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
<url> http://<Network Camera>/setup/network.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 29 www.vivotek.com
29 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
DDNS
“Enable DDNS” This option turns on the DDNS function.
“Provider” The provider list contains four hosts that provide DDNS services. Please
connect to the service provider’s website to make sure the service charges.
“Host Name” If the User wants to use DDNS service, this field must be filled. Please
input the hostname that is registered in the DDNS server.
“Username/E-mail” The Username or E-mail field is necessary for logging in the
DDNS server or notify the User of the new IP address. Note: when this field is input as
“Username” the following field must be input as “Password”.
“Password/Key” Please input the password or key to get the DDNS service.
“Save” Click on this button to save current settings for the DDNS service and UPnP
function.
<url> http://<Network Camera>/setup/ddns.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 30 www.vivotek.com
User's Manual - 30
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Access List
The access list is to control the access permission of clients by checking the client IP
address.
There are two lists for permission control: Allow List and Deny List. Only those
clients whose IP address is in the Allow List and not in the Deny List can connect to
the Video Server or Network Camera for receiving the audio/video streaming.
Both Allow List and Deny List consist of a list of IP ranges. If you want to add a new
IP address range, type the Start IP Address and End IP Address in the text boxes
and click on the Add button. If you want to remove an existing IP address range, just
select from the pull-down menu and click on the Delete button.
Both the Allow List and Deny List can have 20 entries.
<url> http://<Network Camera>/setup/accesslist.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 31 www.vivotek.com
31 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Audio and Video
General
“Configure for computer viewing” To make quick setting for computer viewing
“Configure for mobile viewing” To make quick setting for cell phone viewing
Video Settings
“Video title” The text string can be displayed on video
“Color” Select either for color or monochrome video display.
“Frame Size” There are four options for video sizes. “160x120”. “176x144”,
“320x240”, “640x480”.
“Power line frequency (for fluorescent light)”, the fluorescent light will flash
according to the power line frequency that depends on local utility. Change the
frequency setting to eliminate uncomfortable flash image when the light source is only
fluorescent light.
There are three dependent parameters provided for video performance adjustment.
“key frame interval”
“Max frame rate” This limits the maximal refresh frame rate, which can be combined
with the “Video quality” to optimize bandwidth utilization and video quality. Choose
“Constant bit rate” If the user wants to fix the bandwidth utilization regardless of the
video quality, choose “Fixed quality” and select the desired bandwidth. The video
quality may be poor due to the sending of maximal frame rate within the limited
bandwidth when images are moving rapidly. Consequently, to ensure detailed video
quality (quantization rate) regardless of the network, it will utilize more bandwidth to
send the maximal frames when images change drastically.
Video orientation
“Flip” Vertically rotate the video.
- 32 www.vivotek.com
User's Manual - 32
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
“Mirror” Horizontally rotate the video. Check options both if the Network Camera is
installed upside down.
“White balance” Adjust the value for best color temperature.
Audio settings
“Use” Switch “internal” or “microphone” to set up the source of audio input
“mute” Audio mute
“Boost external microphone input” Enhance the gain of the external microphone
“Internal input Gain” Modify the gain of the internal audio input
“Audio type” Select audio codec “AAC” or “GSM-AMR” and the bit rate
- 33 www.vivotek.com
33 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
<url> http://<Network Camera>/setup/audiovideo.html
<Network Camera> is the domain name or original IP address of the Network Camera.
Image Settings
Click on this button to pop up another window to tune “Brightness”,
“Contrast”, “Hue” and “Saturation” for video compensation. Each field has eleven
levels ranged from -5 to +5.
In
“Brightness”
and
“Contrast” fields the value 0
indicates auto tuning. The
user may press
to
fine-tune the image. When
the image is O.K., press
to set the image settings.
Click on this to recall
the original settings without
incorporating the changes.
- 34 www.vivotek.com
User's Manual - 34
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Email & FTP
Email
When the SMTP server support SMTP authentication, users need to give the valid user
name and password to send email via the server.
“Sender email address”, the email address of the sender.
There are two external mail server can be configured, primary and secondary email
server, The network camera will use primary server as default , and use secondary
server when primary server is unreachable.
“Server address” The domain name or IP address of the external email server.
“User name” This granted user name on the external email server.
“Password” This granted password on the external email server.
“Recipient email address” The email address of the recipients for snapshots or log
file. Multiple recipients must be separated by semicolon, ‘;’.
FTP
“Built-in FTP server port number” This can be other than the default port 21. The
user can change this value from 1025 to 65535. After the changed, the external FTP
client program must change the server port of connection accordingly.
There are two external FTP server can be configured, primary and secondary FTP server,
The network camera will use primary server as default , and use secondary server
when primary server is unreachable.
“Server address” The domain name or the IP address of the external FTP server. The
following user settings must be correctly configured for remote access.
- 35 www.vivotek.com
35 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
“FTP server port” This can be other than the default port 21. The user can change
this value from 1025 to 65535.
“User name” Granted user name on the external FTP server.
“Password” Granted password on the external FTP server.
“Remote folder name” Granted folder on the external FTP server. The string must
conform to that of the external FTP server. Some FTP servers cannot accept preceding
slash symbol before the path without virtual path mapping. Refer to the instructions for
the external FTP server for details. The folder privilege must be open for upload.
<url> http://<Network Camera>/setup/mailftp.html
<Network Camera> is the domain name or original IP address of the Network Camera.
- 36 www.vivotek.com
User's Manual - 36
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Motion detection
“Enable motion detection” Check this option to turn on motion detection.
Click on this button to add a new window. At most three windows can exist
simultaneously. Use the mouse to click, hold, and drag the window frame to resize or
the title bar to move. Clicking on the ‘x’ at the upper right-hand corner of the window
to delete the window. Remember to save in order to validate the changes.
Click on this button to save the related window settings. A graphic bar will rise or
fall depending on the image variation. A green bar means the image variation is under
monitoring level and a red bar means the image variation is over monitoring level.
When the bar goes red, the detected window will also be outlined in red. Going back to
the homepage, the monitored window is hidden but the red frame shows when motion
is detected.
"Window Name" The text will show at the top of the window.
“Sensitivity” This sets the endurable difference between two sequential images.
“Percentage” This sets the space ratio of moving objects in the monitoring window.
Higher sensitivity and small percentage will allow easier motion detection.
The following figure shows the screen when
is clicked. The monitoring window
has been outlined in red and the graphic bar goes red since the goldfish is moving.
- 37 www.vivotek.com
37 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Application settings
Application
Application has two snapshot, one video clip and one digital output.
“Status” ON/OFF show the status of application.
“Sun” ~ “Sat” Select the days of the week to perform the application.
“Time” show “Always” or input the time interval.
“Trigger” Event trigger type has digital input, motion detection and sequential.
“Send” After Event has been triggered, IP cam will send something by email, ftp or
trigger digital output.
- 38 www.vivotek.com
User's Manual - 38
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Snapshot
“Enable snapshot” Enable/Disable snapshot application.
Weekly schedule
“Sun” ~ “Sat” Select the days of the week to perform the application.
Select “Always” or input the time interval.
Snapshot file name prefix
The prefix name will be added on the file name of the snapshot images.
Digital input
Network Camera will send snapshots when the digital input is triggered.
Send out the snapshot while motion detection
There are three windows for motion detection each can be assigned a name. Select the
windows which need to be monitored. If motion detection has not been set up,
“undefined” will be shown instead of the window title. If this happens, clicking on
“Motion detection” and a note will show to direct the User to the configuration page for
motion detection.
“Send pre-event image(s)” The number of pre-snapshots will be captured and send
when a condition is triggered.
“Send post-event image(s)” The number of post-snapshots will be captured and
send when a condition is triggered.
“Delay second(s) before detecting next motion” Set the time delay before
restarting to check on the triggering condition when the current condition is triggered.
- 39 www.vivotek.com
39 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Sequential operation
“Snapshot interval : second(s)” Network Camera will send snapshots at the
specified intervals to the external server using the method selected below. Remember:
This operation is still subject to the conditions set in the weekly schedule.
Method for sending snapshot
“Email” This selects the uploading method following the intervals set above. The
snapshot named “prefix-yyyymmdd-hhmmss.jpg” will be attached in the email.
“FTP” The snapshots will be uploaded to the external FTP server with the file name
defined in the next option. This can also be used to refresh the captured images stored
in the external web server to build creative homepages.
“FTP put snapshots with date and time suffix” This option sets up the snapshot
capture date and time, which can be used to easily differentiate the snapshot file
names in the sequential operation. For instance, “prefix-20030102-030405.jpg”
means the JPEG image was captured in the year 2003, January the 2nd, at 3 o’clock, 4
minute, and 5 second. If this suffix is omitted, the file named “video.jpg” on the
external FTP server will be refreshed at the specified interval.
- 40 www.vivotek.com
User's Manual - 40
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Sequential operation
“Snapshot interval : second(s)” Network Camera will send snapshots at the
specified intervals to the external server using the method selected below. Remember:
This operation is still subject to the conditions set in the weekly schedule.
Method for sending snapshot
“Email” This selects the uploading method following the intervals set above. The
snapshot named “prefix-yyyymmdd-hhmmss.jpg” will be attached in the email.
“FTP” The snapshots will be uploaded to the external FTP server with the file name
defined in the next option. This can also be used to refresh the captured images stored
in the external web server to build creative homepages.
“FTP put snapshots with date and time suffix” This option sets up the snapshot
capture date and time, which can be used to easily differentiate the snapshot file
names in the sequential operation. For instance, “prefix-20030102-030405.jpg”
means the JPEG image was captured in the year 2003, January the 2nd, at 3 o’clock, 4
minute, and 5 second. If this suffix is omitted, the file named “video.jpg” on the
external FTP server will be refreshed at the specified interval.
- 41
40 www.vivotek.com
41 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Video clip
“Enable video clip” Enable/Disable video clip application.
Weekly schedule
“Sun” ~ “Sat” Select the days of the week to perform the application.
Select “Always” or input the time interval.
Video clip file name prefix
The prefix name will be added on the file name of the video clip files.
Video clip max file size
Define the maximal file size of one video clip file.
Digital input
Network Camera will send video clip file when the digital input is triggered.
Send out the video clip while motion detection
There are three windows for motion detection each can be assigned a name. Select the
windows which need to be monitored. If motion detection has not been set up,
“undefined” will be shown instead of the window title. If this happens, clicking on
“Motion detection” and a note will show to direct the User to the configuration page for
motion detection.
“Delay second(s) before detecting next event” Set the time delay before
restarting to check on the triggering condition when the current condition is triggered.
In the event that the available network bandwidth is limited, video clips
sent to FTP or e-mail may be corrupted and can not be opened.
- 42 -
www.vivotek.com
User's Manual - 42
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Sequential operation
“Snapshot interval : second(s)” Network Camera will send video clip file at the
specified intervals to the external server using the method selected below. Remember:
This operation is still subject to the conditions set in the weekly schedule.
Method for sending snapshot
“Email” This selects the uploading method following the intervals set above. The
snapshot named “prefix-yyyymmdd-hhmmss.jpg” will be attached in the email.
“FTP” The snapshots will be uploaded to the external FTP server with the file name
defined in the next option. This can also be used to refresh the captured images stored
in the external web server to build creative homepages.
“FTP put snapshots with date and time suffix” This option sets up the snapshot
capture date and time, which can be used to easily differentiate the snapshot file
names in the sequential operation. For instance, “prefix-20030102-030405.jpg”
means the JPEG image was captured in the year 2003, January the 2nd, at 3 o’clock, 4
minute, and 5 second. If this suffix is omitted, the file named “video.jpg” on the
external FTP server will be refreshed at the specified interval.
- 43 www.vivotek.com
43 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
- 44 www.vivotek.com
User's Manual - 44
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Digital output
“Enable digital output” Enable/Disable digital output application.
Weekly schedule
“Sun” ~ “Sat” Select the days of the week to perform the application.
Select “Always” or input the time interval.
Digital input
Network Camera will trigger digital output when the digital input is triggered.
Trigger digital output while motion detection
There are three windows for motion detection each can be assigned a name. Select the
windows which need to be monitored. If motion detection has not been set up,
“undefined” will be shown instead of the window title. If this happens, clicking on
“Motion detection” and a note will show to direct the User to the configuration page for
motion detection.
“Delay second(s) before detecting next event” Set the time delay before
restarting to check on the triggering condition when the current condition is triggered.
- 45 www.vivotek.com
45 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
- 46 www.vivotek.com
User's Manual - 46
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
System log
The Network camera support log the system messages on remote server. The protocol
is compliant to RFC 3164. If you have external Linux server with syslogd service, use
“-r” option to turn on the facility for receiving log from remote machine. Or you can use
some software on Windows which is compliant to RFC 3164.
Check “Enable remote log” and input the “IP address” and “port” number of the
log server to enable the remote log facility.
In the “Current log”, it displays the current system log file. The content of the log
provides useful information about configuration and connection after system boot- up.
- 47 www.vivotek.com
47 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Viewing system parameters
Click on this link on the configuration page to view the entire system’s parameter set.
The content is the same as those in CONFIG.INI.
- 48 www.vivotek.com
User's Manual - 48
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Maintenance
Three actions can be selected
“reboot” click the reboot button to restart system
“factory default” Click on Factory default button on the configuration page to restore
the factory default settings. Any changes made so far will be lost and the system will be
reset to the initial factory settings. The system will restart and require the installer
program to set up the network again.
“upgrade firmware” Select the firmware file and click upgrade button
- 49 www.vivotek.com
49 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Appendix
A. Troubleshooting
Status LED
The following table lists the LED patterns in general.
Condition
LED color
Loading
system
after power on
Status LED
Color
Steady green and blink red (once)
Description
During
procedure
Blinking booting
red
Steady
green
Power
is being
supplied to the camera.
Detecting and setting network
Steady orange (green + red) till IP address
Solid green
The camera is booting up.
Solid green with blinking red in between
The camera is trying to obtain an IP address.
Solid green and red
An IP address is successfully assigned to the camera.
Solid redthe
with
blinkingfirmware
green in between
During
upgrade
process
TheBlink
camera
is working.
green
/ orange every second and fast
Blinking red and green
blink
red
During
firmware
upgrading
After network is setup (system up)
is confirmed
Blink green / orange every second and
steady red
Reset and restore
There is a button in the back of the Network Camera. It is used to reset the system or
restore the factory default settings. Sometimes resetting the system sets the system
back to normal state. If the system problems remain after reset, restore the factory
settings and install again.
RESET: Click on the button.
RESTORE:
- 50 www.vivotek.com
User's Manual - 50
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
1. Press on the button continuously.
2. Wait for self-diagnostic to run twice.
3. Free the button as soon as the second self-diagnostic starts.
Restoring the factory defaults
will erase any previous settings.
Reset or restore the system after
power on.
B. URL commands of the Network Camera
For some customers who already have their own web site or web control application,
the Network Camera can be easily integrated through convenient URLs. This section
lists the commands in URL format corresponding to the basic functions of the erase
Network Camera.
Get server parameter values
Note: This request require administrator access
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/getparam.cgi?[<parameter>]
[&<parameter>…]
where the <parameter> should be <group>[_<name>] or <group>[.<name>] If you
do not specify the any parameters, all the parameters on the server will be returned. If
you specify only <group>, the parameters of related group will be returned.
When query parameter values, the current parameter value are returned.
- 51 www.vivotek.com
51 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Successful control requests returns paramter pairs as follows.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: <length>\r\n
\r\n
<parameter pair>
where <parameter pair> is
<parameter>=<value>\r\n
[<parameter pair>]
<length> is the actual length of content.
Example: request IP address and it’s response
Request:
http://192.168.0.123/cgi-bin/admin/getparam.cgi?network_ipaddress
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: 33\r\n
\r\n
network.ipaddress=192.168.0.123\r\n
Set server parameter values
Note: This request require administrator access
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/setparam.cgi?
- 52 www.vivotek.com
User's Manual - 52
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
[nosync=<value>&]<parameter>=<value>
[&<parameter>=<value>…][&return=<return page>]
parameter
value
description
<group>_<name>. value to assigned Assign
<value>
to
the
parameter
<group>_<name>..
return
<return page>
Redirect to the page <return page> after the
parameter is assigned. The <return page> can be a
full URL path or relative path according the the current
path. If you omit this parameter, it will redirect to an
empty page.
(note: The return page can be a general HTML
file(.htm, .html) or a Vivotek server script executable
(.vspx) file. It can not be a CGI command. It can not
have any extra parameters. This parameter must be
put at end of parameter list)
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: <length>\r\n
\r\n
<parameter pair>
where <parameter pair> is
<parameter>=<value>\r\n
[<parameter pair>]
Only the parameters that you set and readable will be returned.
Example: Set the IP address of server to 192.168.0.123
- 53 www.vivotek.com
53 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Request:
http://myserver/cgi-bin/admin/setparam.cgi?Network_IPAddress=192.168.0.123
Response:
HTTP/1.0 200 OK\r\n
Content-Type: text/html\r\n
Context-Length: 33\r\n
\r\n
network.ipaddress=192.168.0.123\r\n
Available parameters on the server
NOTE: The bold characters in table are the default value of each parameter.
Group: System
NAME
VALUE
DESCRIPTION
hostname
<text
(r/w)
than 40 characters>
<<Wireless>Network Camera >
ledoff
0
Do not turn off the led indicator
(r/w)
1
Turn off the led indicator
date
<yyyy/mm/dd>
year, month and date separated by slash.
(r/w)
<keep>
keep date unchanged
<auto>
Using NTP to sync date/time automatically
time
<hh:mm:ss>
hour, minute and second separated by colon.
(r/w)
<keep>
keep date unchanged
<auto>
Using NTP to sync date/time automatically
string
shorter host name of server
ntp
<domain name or IP NTP server
(r/w)
address>
<skip to invoke default server>
timezone
-12 ~ 12
time zone, 8 means GMT +8:00
(r/w)
<8>
- 54 www.vivotek.com
User's Manual - 54
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
updateinterval
0 ~ 2592000
0 to Disable automatic time adjustment,
(r/w)
otherwise, it means the seconds between
NTP automatic update interval.
<0>
serialnumber
<mac address>
12 characters mac address without hyphen
(r)
connected
firmwareversion
<text
string
shorter The version of firmware, including model,
(r)
than 39 characters>
company, and version number
restore
0
Restore the system parameters to default
(w)
value.
Positive integer
Restore the system parameters to default
value and restart the server after <value>
seconds.
reset
0 ~ 65535
Restart the server after <value> seconds.
-1
Not restart the server.
viewmode
0
Using the profile of viewing by computer
(r/w)
1
Using the profile of viewing by mobile phone
(w)
Group: Security
NAME
VALUE
DESCRIPTION
username_<1~20 <text string shorter change user name.
>
than 16 characters> <blank>
(r/w)
userpass_<0~20> <text string shorter change user’s password.
(r/w)
than 14 characters> The UserPass_0 is root’s password.
<blank>
userattr_<1~20> [conf]
show user’s privilege. The privilege can be
(r)
<blank> - only permit to view live media
conf – Permit to change server’s configuration
<blank>
usercount
1 ~ 21
The current account number on the server
- 55 www.vivotek.com
55 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
(r)
including root.<1>
Group: Network
NAME
VALUE
DESCRIPTION
type
0
LAN
(r/w)
1
PPPoE
pppoeuser
<text string shorter than PPPoE account user name
(r/w)
80 characters>
pppoepass
<text string shorter than PPPoE account password
(r/w)
15 characters>
<blank>
resetip
1
enable to get ipaddress, subnet, router, dns1,
<blank>
(r/w)(restart)
dns2 from DHCP server at next reboot
0
Using preset ipaddress, subnet, router, dns1,
dns2
ipaddress
<IP address>
IP address of server
(r/w) (restart)
subnet
<192.168.0.99>
<IP address>
subnet mask
(r/w) (restart)
router
<255.255.255.0>
<IP address>
default gateway
(r/w) (restart)
dns1
<blank>
<IP address>
primary DNS server
(r/w) (restart)
dns2
<blank>
<IP address>
secondary DNS server
(r/w) (restart)
<blank>
name
or
IP primary SMTP server
smtp1
<domain
(r/w)
address, string shorter <blank>
than 40 characters>
mailto1
<string shorter than 80 mail recipient address
(r/w)
characters>
mailuser1
<text string shorter than User name of primary smtp server
(r/w)
63 characters>
mailpass1
<text string shorter than Password of primary smtp server
(r/w)
15 characters>
<blank>
<blank>
<blank>
- 56 www.vivotek.com
User's Manual - 56
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
name
or
IP secondary SMTP server
smtp2
<domain
(r/w)
address, string shorter <blank>
than 40 characters>
mailto2
<text string shorter than mail recipient address
(r/w)
80 characters>
mailuser2
<text string shorter than User name of secondary smtp server
(r/w)
63 characters>
mailpass2
<text string shorter than Password of secondary smtp server
(r/w)
15 characters>
returnemail
<text string shorter than return email address
(r/w)
80 characters>
localftpport
<positive
(r/w)
than 65535>
ftp1
<domain
(r/w)
address, string shorter <blank>
<blank>
<blank>
<blank>
<blank>
number
name
less FTP port
<21>
or
IP primary FTP server
than 40 characters >
ftpport1
<positive
number
less primary FTP port
(r/w)
than 65535>
ftpuser1
<text string shorter than user name for primary FTP server
(r/w)
63 characters>
ftppass1
<text string shorter than password for primary FTP server
(r/w)
15 characters>
ftpfolder1
<text string shorter than upload folder in primary FTP server
(r/w)
40 characters>
<21>
<blank>
<blank>
<blank>
ftppasvmode1 1
Enable passive mode of primary FTP server
(r/w)
0
Disable passive mode of primary FTP server
ftp2
<domain
(r/w)
address, string shorter
name
or
IP secondary FTP server
than 40 characters >
ftpport2
<positive
number
less secondary FTP port
(r/w)
than 65535>
ftpuser2
<text string shorter than user name for secondary FTP server
(r/w)
63 characters>
<21>
<blank>
- 57 www.vivotek.com
57 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
ftppass2
<text string shorter than password for secondary FTP server
(r/w)
15 characters>
ftpfolder2
<text string shorter than upload folder in secondary FTP server
(r/w)
40 characters>
<blank>
<blank>
ftppasvmode2 1
Enable passive mode of primary FTP server
(r/w)
0
Disable passive mode of primary FTP server
httpport
<positive
number
less HTTP port
(r/w) (restart) than 65535>
rtspport
<positive
<80>
number
less RTSP port
(r/w) (restart) than 65535>
<554>
videoport
<positive
number
less video Channel port for RTP
(r)
than 65535>
audioport
<positive
(r)
than 65535>
accessname
<text string shorter than RTSP access name
(r/w)
20 characters>
<5558>
number
less audio Channel port for RTP
<5556>
<live.sdp>
Group: IPFilter
NAME
VALUE
DESCRIPTION
allowstart_<0~9> 1.0.0.0
(r/w)
~ Allowed starting RTSP connection IP address
255.255.255.255
allowend_<0~9> 1.0.0.0
(r/w)
~ Allowed ending RTSP connection IP address
255.255.255.255
denystart_<0~9> 1.0.0.0
(r/w)
<255.255.255.255>
~ Denied starting RTSP connection IP address
255.255.255.255
denyend_<0~9> 1.0.0.0
(r/w)
<1.0.0.0>
<blank>
~ Denied ending RTSP connection IP address
255.255.255.255
<blank>
Group: Video
NAME
VALUE
DESCRIPTION
text
<text
(r/w)
than 14 characters>
<blank>
codectype
0
MPEG4
string
shorter enclosed caption
- 58 www.vivotek.com
User's Manual - 58
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
(r/w)
1
MJPEG
keyinterval
1, 3, 5, 10, 30, 60, 90, Key frame interval
(r/w)
120
<60>
size
1
half
(r)
2
half x 2
3
normal
4
normal x 2
5
double
256
This field is obsolete (use resolution)
resolution
176x144 (for mobile) Video resolution 176 x 144
(r/w)
160x120
Video resolution 160 x 120
320x240
Video resolution 320 x 240
640x480
(for Video resolution 640 x 480
computer)
color
0
monochrome
(r/w)
1
color
quality
0
fix bit rate
(r/w)
1
fix quantization
quant
1
lowest quality of video
(r/w)
2
lower quality of video
3
normal quality of video
4
higher quality of video
5
highest quality of video
bitrate
20000
set bit rate to 20K bps
(r/w)
30000
set bit rate to 30K bps
40000
set bit rate to 40K bps
50000
set bit rate to 50K bps
64000
set bit rate to 64K bps
128000
set bit rate to 128K bps
256000
set bit rate to 256K bps
512000
set bit rate to 512K bps
768000
set bit rate to 768K bps
- 59 www.vivotek.com
59 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
1000000
set bit rate to 1000K bps
1500000
set bit rate to 1500K bps
2000000
set bit rate to 2000K bps
3000000
set bit rate to 3000K bps
4000000
set bit rate to 4000K bps
maxframe
1
set maximum frame rate to 1 fps
(r/w)
2
set maximum frame rate to 2 fps
3
set maximum frame rate to 3 fps
5
set maximum frame rate to 5 fps
10
set maximum frame rate to 10 fps
15
set maximum frame rate to 15 fps
20
set maximum frame rate to 20 fps
25
set maximum frame rate to 25 fps
30 (for 60Hz only)
set maximum frame rate to 30 fps
50
synchronize with 50Hz utility
(r/w) (in CMOS 60
synchronize with 60Hz utility
mode
version only)
whitebalance
0
auto white balance
(r/w) (in CMOS 1
fixed indoor(3200K)
version only)
2
fixed fluorescent (5500K)
3
fixed outdoor( > 5500K)
flip
1
flip image
(r/w)
0
normal image
mirror
1
mirror image
(r/w)
0
normal image
imprinttimestam 1
Overlay time stamp on video
p
Do not overlay time stamp on video
0
(r/w)
Group: Audio
NAME
VALUE
DESCRIPTION
type
AAC4 (for computer) set codec to AAC
- 60 www.vivotek.com
User's Manual - 60
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
(r/w)
GAMR (for mobile)
set codec to GSM-AMR
aacbitrate
16000
set AAC bitrate to 16K bps
(r/w)
32000
set AAC bitrate to 32K bps
48000
set AAC bitrate to 48K bps
64000
set AAC bitrate to 64K bps
96000
set AAC bitrate to 96K bps
128000
set AAC bitrate to 128K bps
amrbitrate
4750
set AMR bitrate to 4.75K bps
(r/w)
5150
set AMR bitrate to 5.15K bps
5900
set AMR bitrate to 5.9K bps
6700
set AMR bitrate to 6.7K bps
7400
set AMR bitrate to 7.4K bps
7950
set AMR bitrate to 7.95K bps
10200
set AMR bitrate to 10.2K bps
12200
set AMR bitrate to 12.2K bps
Group: Image
NAME
VALUE
DESCRIPTION
brightness
<-5 ~ 5>
Adjust brightness of image according to mode
(r/w)
saturation
settings. <0>
<-5 ~ 5>
Adjust saturation of image according to mode
(r/w)
contrast
settings. <0>
<-5 ~ 5>
Adjust contrast of image according to mode
(r/w)
hue
settings. <0>
<-5 ~ 5>
Adjust hue of image according to mode
(r/w)
settings. <0>
Group: Motion
NAME
VALUE
DESCRIPTION
enabled
0
disable motion detection
(r/w)
1
enable motion detection
winenabled_<0~2> 0
disable motion window #1
- 61 www.vivotek.com
61 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
(r/w)
1
enable motion window #1
winname_<0~2>
<text
(r/w)
than 14 characters >
<blank>
winleft_<0~2>
0 ~ 320
Left coordinate of window position.
string
shorter name of motion window #1
(r/w)
<0>
wintop_<0~2>
0 ~ 240
Top coordinate of window position.
(r/w)
<0>
winwidth_<0~2>
0 ~ 320
Width of motion detection window.
(r/w)
<0>
winheight_<0~2>
0 ~ 240
Height of motion detection window.
(r/w)
<0>
winobjsize_<0~2>
0 ~ 100
Percent of motion detection window
(r/w)
<0>
winsensitivity_<0~2 0 ~ 100
Sensitivity of motion detection window
>
<0>
(r/w)
update
1
Update the above motion detection settings
(w)
to take effect
Group: DDNS
NAME
VALUE
DESCRIPTION
enable
0, 1
Enable or disable the dynamic dns.
(r/w)
provider
<0>
1~6
dyndns.org (dynamic)
(r/w)
dyndns.org (custom)
tzo.com
dhs.org
safe100.net
dyn-interfree.it
<1>
hostname
Text string shorter than Your dynamic hostname.
(r/w)
127 characters.
<blank>
usernameemail Text string shorter than 63 Your user or email to login ddns service
- 62 www.vivotek.com
User's Manual - 62
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
(r/w)
characters.
provider
<blank>
passwordkey
Text string shorter than 20 Your password or key to login ddns service
(r/w)
characters.
provider
<blank>
update
0, 1
Update the above ddns settings to take
(w)
effect
Group: UPNP
NAME
VALUE
DESCRIPTION
enable
0, 1
Enable or disable the UPNP presentation
(r/w)
service.
<1>
Group: UPNPfor
NAME
VALUE
DESCRIPTION
enable
0, 1
Enable or disable the UPNP port forwarding
(r/w)
service.
<0>
Group: App
NAME
VALUE
DESCRIPTION
scriptname
<text string shorter than File name of script
(r)
255 characters>
<script.vssx>
enablescript
0
Disable script
(r/w)
1
Enable script
Group: Syslog
NAME
VALUE
DESCRIPTION
enableremotelog
0
disable remote log
(r/w)
1
enable remote log
- 63 www.vivotek.com
63 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
serverip
<IP address>
Log server IP address
<514>
Server port used for log
(r/w)
serverport
(r/w)
Application page CGI command
Note: This request requires administrator privilege.
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/gen-eventd-conf.cgi?[ snapshot_enable=<value>]
[&weekday=<value>][&time_method=<value>][&begin_time=<value>]
[&end_time=<value>]
[&ss_prefix=<value>][&trigger_type=<value>]
[&md_prenum=<value>][&md_postnum=<value>][&md_delay=<value>]
[&sq_interval=<value>]
[&send_method=<value][&ftp_suffix=<value>]
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <length>\r\n
\r\n
<depends on method value>
If(method == get || method == set)
{
tue=<value>\r\n
wed=<value>\r\n
…
}
- 64 www.vivotek.com
User's Manual - 64
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Else if(method == normal)
{
Application page contents
}
parameter
Value
description
snapshot_enable 0
Enable snapshot application
1
Disable snapshot application
weekday
0,1,2,3,4,5,6
The array indicate weekly schedule
time_method
always
24 hours full day
interval
Select begin time and end time
begin_time
hh:mm
Begin time of weekly schedule
end_time
hh:mm
End time of weekly schedule
ss_prefix
<text string
Snapshot file name prefix for both event and
shorter than 60
sequential operation
characters>
trigger_type
motion
Set trigger by motion detect
sequential
Snapshot sequentially
md_win
0,1,2
The array indicate which motion windows are used
md_prenum
1~5
The numbers of snapshot before event
md_postnum
1~5
The numbers of snapshot after event
md_delay
1~999
The delay seconds for detecting next motion event
sq_interval
1~999
The interval seconds of sequential snapshot
send_method
mail
Send snapshot by mail
ftp
Send snapshot by ftp
0/1
Enable/Disable file name prefix
ftp_suffix
Capture single snapshot
Note: This request require normal user privilege
Method: GET/POST
- 65 www.vivotek.com
65 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Syntax:
http://<servername>/cgi-bin/video.jpg
Server will return the most up-to-date snapshot in JPEG format. The size and quality of
image will be set according to the video settings on the server.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: image/jpeg\r\n
[Content-Length: <image size>\r\n]
<binary JPEG image data>
Account management
Note: This request requires administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/editaccount.cgi?
method=<value>&username=<name>[&userpass=<value>][&privilege=<value>]
[&privilege=<value>][…][&return=<return page>]
parameter
value
Description
method
add
Add an account to server. When using this method,
“username” field is necessary. It will use default value
of other fields if not specified.
delete
Remove an account from server. When using this
method, “username” field is necessary, and others are
ignored.
- 66 www.vivotek.com
User's Manual - 66
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
edit
Modify the account password and privilege. When
using this method, “username” field is necessary, and
other fields are optional. If not specified, it will keep
original settings.
username
<name>
The name of user to add, delete or edit
userpass
<value>
The password of new user to add or that of old user to
modify. The default value is an empty string.
privilege
<value>
The privilege of user to add or to modify. The privilege
can be the addition of the following values. Ex: A user
with configure access can be assigned privilege as
privilege=conf.
return
conf
configuration privilege
<return page>
Redirect to the page <return page> after the
parameter is assigned. The <return page> can be a
full URL path or relative path according the the current
path. If you omit this parameter, it will redirect to an
empty page.
System logs
Note: This request require administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/syslog.cgi
Server will return the up-to-date system log.
Return:
HTTP/1.0 200 OK\r\n
- 67 www.vivotek.com
67 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Content-Type: text/plain\r\n
Content-Length: <syslog length>\r\n
\r\n
<system log information>\r\n
Configuration file
Note: This request requires administrator privilege
Method: GET/POST
Syntax:
http://<servername>/cgi-bin/admin/configfile.cgi
Server will return the up-to-date configuration file.
Return:
HTTP/1.0 200 OK\r\n
Content-Type: text/plain\r\n
Content-Length: <configuration file length>\r\n
\r\n
<configuration data>\r\n
Upgrade firmware
Note: This request requires administrator privilege
Method: POST
Syntax:
http://<servername>/cgi-bin/admin/upgrade.cgi
- 68 www.vivotek.com
User's Manual - 68
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Post data:
fimage=<file name>[&return=<return page>]\r\n
\r\n
<multipart encoded form data>
Server will accept the upload file named <file name> to be upgraded the firmware and
return with <return page> if indicated.
- 69 www.vivotek.com
69 - User's Manual
Specifications
D. Technical specifications
C.
Models
.IP7131 (PoE)
.IP7132 (WLAN)
System
.CPU: VVTK-1000 SoC
.Flash: 4MB
.RAM: 32MB SDRAM
.Embedded OS: Linux 2.4
- System
Viewing System
Requirements
- Audio
CPU: Vivotek VVTK-1000
Supports GSM-AMR
.Installation Wizard 2
Installation, Management,
.16-CH recording software
Supports AAC compression
and Maintenance
.Supports firmware upgrade
Lens
RAM: 32MB SDRAM .CS mount, f=4.0 mm, F2.0, Fixed
ROM:Time
4MB FLASH ROM
.1/60 sec. to 1/15000 sec.
Shutter
Supports audio mute
Image Sensor: VGA CMOS
.1/4” CMOS sensor in VGA resolution
Image Sensor
Embedded OS: Linux2.4
D. Technical specifications
Minimum
Illumination
.OS: Microsoft Windows 2000/XP/Vista
.Browser: Mozilla Firefox, Internet Explorer 6.x
or above
.Cell phone: 3GPP player
.Real Player: 10.5 or above
.Quick Time: 6.5 or above
P/N: 011000102 Ver 1.0
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
.1.5 Lux / F2.0
Applications
Bit rate:
.SDK available for application development
and system integration
GSM-AMR: 4.75k~12.2k
.12 months
Warranty
ACC: 15k~128k
- Networking
Video
.Compression:
- Security System overview
MPEG-4 for streaming video
JPEG
for
still
image
TCP/IP, HTTP, SMTP, FTP, DDNS, UPnP, Telnet, NTP, DNS, DHCP
- System
- AudioMulti-level user access
.Streaming:
MPEG-4 streaming over UDP, TCP, or HTTP
address filtering
and VVTK-1000
RTSP
CPU: Vivotek
Supports IP
GSM-AMR
MPEG-4 multicast streaming
Physical
RAM: 32MB
SDRAM
Supports
AAC
compression
.Supports 3GPP mobile surveillance
Router
.Frame rates:
LED
indicator
auto negotiation
ROM: 4MB10/100
FLASHbaseT
ROM Fast Ethernet
Supports audio
mute
MPEG-4: Up to 30/25 fps at 640x480
External
Protocols
Bit rate:
MicrophoneBi-color LED system status indicator
Image Sensor: VGA CMOS
Image
Settings
.Adjustable image size, quality, and bit rate
- OS:
Video
Embedded
Linux2.4
.Time stamp and text caption overlay
Algorithm supported
.Flip & mirror
.Configurable brightness, sharpness,
MPEG4(simple profile) saturation
for streaming
video
- Networking
and contrast
3G Cell Phone
IP7131
GSM-AMR: 4.75k~12.2k
- Dimension
ACC: 15k~128k
126.4mm (L) Router
x 96.2mm (W) x 47.4mm (H)
ProtocolsJPEG for still image .AWB, AES
Features
TCP/IP, HTTP,
SMTP, FTP, DDNS, UPnP, Telnet, NTP, DNS, DHCP
- Security
Weight
Multi-level- user
access
.Compression:
Adjustable image size,
quality and bit rate
and RTSPAudio
GSM-AMR speech compression, bit rate:
4.75 kbps ~ 12.2 kbps
Physical Time stamp and text overlay
276g
IP addressNET.
filtering
Notebook with
Web Browser
PC with
Recording Software
MPEG-4 AAC audio encoding, bit rate:
- Power
- LED indicator
160x120
- VideoUp to 30/25 frames at External
microphone input
Built-in microphone
12Vsystem
DC
Bi-color LED
status indicator
Power over Ethernet: 802.3af compliant
Upsupported
to 30/25 frames at 320x240
Algorithm
Networking
Up toprofile)
30/25 frames
at
640x480
MPEG4(simple
for streaming
video
.10/100
Mbps Ethernet, RJ-45
126.4mm (L) x 96.2mm (W) x 47.4mm (H)
3 motion
detectionauto
windows
10/100 baseT
Fast Ethernet
16negotiation
kbps ~ 128 kbps
.Interface:
Resolution
External
View
Power Consumption:
2.7W
- Dimension
4.4W
.Supports audio mute
JPEG for still image
.Built-in 802.11b/g WLAN (IP7132)
.Protocols: IPv4, TCP/IP, HTTP, UPnP, RTSP/
RTP/RTCP, IGMP, SMTP, FTP, DHCP, NTP,
Specification
DNS, DDNS, and PPPoE
Features- Camera
inch size,
colorquality
CMOS and
sensor
Adjustable1/4
image
bit rate
Alarm
andtext overlay
Resolution:
640x480 .Triple-window video for motion detection
Time stamp
and
- Operating Environment
Indented
Temperature:
0-40°C/32-104°F
- Weight
MIC In
Reset
Button
NET. 276gHumidity: 20%~80% RH
Event Management
.One D/I and one D/O for external sensor and alarm
.Event notification using HTTP, SMTP, or FTP
- Powe-r EMI & Safety
Security
.Multi-level user access with password protection
12V DC
1.5Lux/F2.0
3 motion detection
windows
AGC, AWB, AES
Resolution
Power Cord
Socket
CE, FCC, PSE
.IP address
filtering second
Electronic
1/60
~ 1/15000
Up to 30/25
frames shutter:
at 160x120
Power over Ethernet: 802.3af compliant
Up to 30/25
frames at 320x240
.Camera live viewing for up to 10 clients
Users
-Socket
Application
PowerRJ45
Consumption:
2.7W
Installation wizard
- Lens
Up to 30/25
frames at 640x480
Dimension
.177 mm (D) x 96.2 mm (W) x 47.4 mm (H)
Fixed focal with fine tuning, 4.0mm, F2.0
276 g (IP7131)
Weight
- Camera
Specification.Net:
.Net: 292 g (IP7132)
- Stream
1/4 inch color
CMOS sensor
LED Indicator
Wireless Antenna
Connector
Ethernet 10/100
General I/O
Terminal Block
16-ch recording
software
- Operating
Environment
SDK 0-40°C/32-104°F
available for application development and system
Temperature:
Accessories
Humidity:integration
20%~80% RH
.System power and status indicator
MPEG-4
streaming over
UDP,activity
TCP, and
ir HTTP
Resolution:
640x480
.System
network link indicator
MPEG-4 multicast streaming
1.5Lux/F2.0
- Viewing system requirement
Microsoft Windows 2000/XP
- EMI &OS:
Safety
.12V DC
Browser: Internet Explorer 5.x or above
CE, FCC, PSE
.Power consumption: Max. 4.4 W (IP7131)
.Power consumption: Max. 4.9 W (IP7132)
Event1/60
Management
Cellphone: 3GPP player
Electronic-shutter:
~ 1/15000
second
.802.3af compliant Power-over-Ethernet (IP7131)
Power
AGC, AWB, AES
Real Player 10.5
- Application
Multiple-window video motion detection
- Lens
Approvals
.CE, LVD, FCC, VCCI
1 digital input and 1 digital output
.Temperature:
0 ~ 50of°CFTP
(32 ~ 122 °F)
Operating
Environments
Event
HTTP,
SMTP,
Fixed focal
with notification
fine
tuning,using
4.0mm,
F2.0
.Humidity: 20% ~ 80% RH
- Stream
MPEG-4 streaming over UDP, TCP, ir HTTP
Distributed by:
MPEG-4 multicast streaming
Quick
Time 6.5
Installation
wizard
Enclosure
Packet software
Video Player 3.0
16-ch recording
PoE Injector
SDK available for application development and system
integration
- 70 -
Copyright c 2009 VIVOTEK INC. All rights reserved.
- Viewing system requirement
OS: Microsoft Windows 2000/XP
Browser: Internet Explorer 5.x or above
- Event Management
Multiple-window video motion detection
www.vivotek.com
Cellphone:
3GPPLien-Cheng
player Rd., Chung-Ho, Taipei
6F, No.192,
County, Taiwan
Tel: +88610.5
2 8245 5282| Fax: +886 2 8245 5532| E-mail: sales@vivotek.com
Real Player
1 digital input and 1 digital output
USA, INC.
Quick VIVOTEK
Time 6.5
Event notification using HTTP, SMTP, of FTP
PacketTel:
Video
Player| 3.0
408-773-8686
Fax: 408-773-8298
User's Manual - 70
470 Lakeside Drive Suite C, Sunnyvale, CA 94085 USA
| E-mail: salesusa@vivotek.com
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Technology License
Notice
Technology
License
Notice
MPEG-4
AAC Technology
AMR Technology
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 AAC AUDIO PATENT LICENSE. THIS
PRODUCT MAY NOT BE DECOMPILED, REVERSE-ENGINEERED OR COPIED, EXCEPT REGARD
This product includes AMR narrowband speech coding technology licensed by
TO PC SOFTWARE, YOU MAY MAKE SINGLE COPIES FOR ARCHIVAL PURPOSES. FOR MORE
VoiceAge. Please refer to http://www.voiceage.com/ for more details.
INFORMATION, PLEASE REFER TO HTTP://WWW.VIALICENSING.COM.
MPEG-4 AAC Technology
MPEG-4 Visual Technology
This product includes MPEG-4 AAC audio coding technology licensed by Via Licensing.
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR
Please
refer toAND
http://www.vialicensing.com/
more details.
THE
PERSONAL
NON-COMMERCIAL USE OF A for
CONSUMER
FOR (i) ENCODING VIDEO
IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD ("MPEG-4 VIDEO") AND/OR (ii)
DECODING
MPEG-4 VIDEO
THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL
MPEG-4 Visual
Technology
AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER
LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL
This product includes one MPEG-4 encoder and one MPEG-4 decoder license.
BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING
Installation
of more
than one
is prohibited.
Please
contact
your
reseller to
TO
PROMOTIONAL,
INTERNAL
ANDdecoder
COMMERCIAL
USES AND
LICENSING
MAY
BE OBTAINED
FROM
MPEGadditional
LA, LLC. SEE
HTTP://WWW.MPEGLA.COM.
purchase
decoder
licenses.
THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO
LICENSE FOR
THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i)
AMR-NB
Standard
THIS
PRODUCT
IS LICENSED
UNDER THE
AMR-NB
PATENTSTANDARD
LICENSE AGREEMENT.
ENCODING
VIDEO
IN COMPLIANCE
WITH
THE STANDARD
MPEG-4 VISUAL
("MPEG-4
WITH
RESPECT
TO
THE
USE
OF
THIS
PRODUCT,
THE
FOLLOWING
LICENSORS’
PATENTS
MAY
VIDEO") AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY
A
APPLY:
CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR
TELEFONAKIEBOLAGET ERICSSON AB: US PAT. 6192335; 6275798; 6029125; 6424938;
WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE
6058359. NOKIA CORPORATION: US PAT. 5946651; 6199035. VOICEAGE CORPORATION:
MPEG-4
VIDEO. BE
NOPAT.
LICENSE
IS CA
GRANTED
OR SHALL
BE0516621;
IMPLIED DE
FOR
ANY
OTHER
AT
PAT. 0516621;
0516621;
PAT. 2010830;
CH PAT.
PAT.
0516621;
USE.
THAT
RELATING
TOGR
PROMOTIONAL,
DK
PAT.ADDITIONAL
0516621; ES INFORMATION
PAT. 0516621; FRINCLUDING
PAT. 0516621;
GB PAT.
0516621;
PAT. 0516621;
IT
PAT.
0516621;
LI
PAT.
0516621;
LU
PAT.
0516621;
NL
PAT.
0516621;
SE
PAT
0516621;
US
INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM
MPEG
PAT
PAT. 819303/AT E 198805T1; AU PAT. 697256; BE PAT. 819303; BR PAT.
LA, 5444816;
LLC. SEE AT
HTTP://WWW.MPEGLA.COM.
9604838-7; CA PAT. 2216315; CH PAT. 819303; CN PAT. ZL96193827.7; DE PAT. 819303/
DE69611607T2; DK PAT. 819303; ES PAT. 819303; EP PAT. 819303; FR PAT. 819303; GB PAT.
819303; IT PAT. 819303; JP PAT. APP. 8-529817; NL PAT. 819303; SE PAT. 819303; US PAT.
5664053. THE LIST MAY BE UPDATED FROM TIME TO TIME BY LICENSORS AND A CURRENT
VERSION OF WHICH IS AVAILABLE ON LICENSOR’S WEBSITE AT HTTP://WWW.VOICEAGE.
COM.
- 71 www.vivotek.com
71 - User's Manual
VIVOTEK - A Leading Provider of Multimedia Communication Solutions
Electromagnetic Compatibility (EMC)
FCC Statement
This device compiles with FCC Rules Part 15. Operation is subject to the following two conditions.
■ This device may not cause harmful interference, and
■ This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a partial
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
■ Reorient or relocate the receiving antenna.
■ Increase the separation between the equipment and receiver.
■ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
■ Consult the dealer or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Liability
VIVOTEK Inc. cannot be held responsible for any technical or typographical errors and reserves the right
to make changes to the product and manuals without prior notice. VIVOTEK Inc. makes no warranty
of any kind with regard to the material contained within this document, including, but not limited to, the
implied warranties of merchantability and fitness for any particular purpose.
User's Manual - 72