DCS RDS-305 Installation guide

THE RDS PROFESSIONAL RANGE
Installation Guide
MODELS:
RDS-305
RDS-366
RDS-364GL
RDS-364GD
RDS-484GG
RDS-485GD
RDS-486GL
RDS-486GD
A MESSAGE TO OUR CUSTOMERS
Thank you for selecting this DCS RDS Range. Because of this appliance’s unique features we have developed
this Installation Guide. It contains valuable information on how to properly install your new appliance for
years of safe and enjoyable cooking.
For your convenience, product questions can be answered by a DCS Customer Service Representative by
phone: 1-888-281-5698, Fax: 714-372-7004, email: support@dcsappliances.com, or by mail:
DCS
Attention: Customer Service
5800 Skylab Road
Huntington Beach, CA 92647
www.dcsappliances.com
WARNING
If the information in this manual is not followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
PRECAUTION
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
FOR YOUR SAFETY
IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
If you cannot reach your gas supplier, call the fire department.
Installation and service must be performed by a qualified installer, service
agency or the gas supplier.
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
1
TABLE OF CONTENTS
INTRODUCTION ..................................................................................................................................................................3
MODELS ....................................................................................................................................................................................4
PLANNING THE INSTALLATION ..............................................................................................................................5
UNPACKING AND HANDLING .............................................................................................................................5-7
VENTILATION REQUIREMENTS ...............................................................................................................................8
INSTALLING ANTI-TIP DEVICE .................................................................................................................................9
CABINET PREPARATION ......................................................................................................................................10-12
BACKGUARD INSTALLATION .................................................................................................................................13
ELECTRICAL / GAS CONNECTIONS .............................................................................................................13-14
HOOK-UP TO GAS SUPPLY ................................................................................................................................14-15
TEST AND ADJUSTMENTS .......................................................................................................................................16
INSTALLER FINAL CHECKLIST ...............................................................................................................................17
WIRING DIAGRAMS ................................................................................................................................................18-25
RDS 48”Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
RDS 48”Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
RDS 36”Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
RDS 36”Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
RDS 485 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
RDS 485 Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
RDS 305 Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
RDS 305 Wiring Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
HOW TO OBTAIN SERVICE........................................................................................................................................26
WARRANTY ..........................................................................................................................................................................27
2
INTRODUCTION
DCS Professional Ranges are designed with a number of features and are available in a multitude of
different combinations: top burner sections, thermostatic griddles, and grills. Ranges are available in
30”, 36”, and 48” widths. The large capacity electric ovens of the Dual Fuel Range are self-cleaning and
convection. The secondary electric oven found on the left side of the 48” Dual Fuel Range can Bake or
Broil, and also has a Proof feature. All range models require the installation of one of the two (12” or
30”) offered Backguards. (Unless island installation).
IMPORTANT INSTALLATION INFORMATION
The RDS Series is tested in accordance to UL Standard 858 and ANSI Z21.1. These ranges must be
installed in conjunction with a suitable overhead vent hood. Due to the professional high heat
capacity of this unit, particular attention should be paid to the hood and duct work installation to
ensure it meets local building codes. To eliminate risk of burns or fire by reaching over heated surface
units, cabinet storage located above the surface units should be avoided.
Check local building codes for the proper method of range installation. Local codes vary. Installation,
electrical connections, and grounding must comply with all applicable codes. In the absence of local
codes, the range should be installed in accordance with the National Fuel Gas Code ANSI Z223.1-1988
and National Electrical Code ANSI / NFPA 70-1990. Be sure that the unit being installed is set up for the
kind of gas being used. The gas range is shipped from the factory set and adjusted for Natural Gas or
LP (propane), depending on the specific model ordered. Verify that the range is compatible with
gas supply at the installation site before proceeding further. Return range to dealer if unit is not
set for site gas supply.
3
MODELS
48” RDS RANGE MODELS
RDS-484GG
RDS-486GL
RDS-486GD
RDS-364GL
RDS-364GD
RDS-485GD
36” RDS RANGE MODELS
RDS-366
30” RDS RANGE MODELS
OVEN ON
HEATING
HEATING
DOOR LOCKED
RDS-305
4
PLANNING THE INSTALLATION
RECOMMENDED INSTALLATION INSTRUCTION
Install components in the following order:
A) Vent Hood
B) Backguard System
C) Range
1) Locate and level range according to range installation instructions.
2) Measure distance from floor to top of island trim on range, adding 1/8” for backguard clearance.
3) Transfer this measurement to the wall. This will mark the bottom of your backguard.
4) From this line measure 28” up wall to mark top of 30” backguard. This is the minimum height
that the bottom of your vent hood can be installed.
6) Follow vent hood manufacturer’s installation instructions to install vent hood.
7) Follow backguard installation instructions to install backguard.
8) Connect gas and electric connections and slide range into position.
UNPACKING AND HANDLING
STEP 1:
MOVING AND PLACING THE RANGE
The ranges have shipping weights varying from
420lbs. to 630lbs less approx. 50lbs. after removal of
packing material. It is recommended that the
door(s), grates, front kick panel, and drip pan (below
knobs) be removed to facilitate handling. This will
reduce the weight for ease of handling.
Kick Panel
Panel
Kick
Fig. 1
5
UNPACKING AND HANDLING
CAUTION:
Proper equipment and adequate manpower must be used in moving the range
to avoid damage to the unit or the floor. The unit is heavy and rests on
adjustable steel legs.
WARNING:
DO NOT lift range by the oven door handles!!
WARNING:
DO NOT remove the grill or griddle assemblies!!
It may be necessary to remove the oven doors and
knobs to pass through some doorways. With the
doors and knobs removed, a 29 1/16” (RDS 36/48)
29 3/8” (RDS 305) wide opening is required.
Without removing the door, a 31 1/2” (RDS 36/48) /
30” (RDS 305) wide opening is required. Remove
the outer carton and packing material from the
shipping base.
Left
Rear
Left Rear Shipping
Shipping
Screws
Screws
Remove the kick panel by removing two screws at
the top and pulling forward. The range is held to
the skid by two bolts in the front behind the kick
panel, (fig. 1) and two L-brackets located on the
bottom flange of the range back (fig . 2). After
removing the bolts and brackets, the range must be
lifted and removed from the skid.
Fig. 2
Due to the weight, a dolly with soft wheels should
be used to move this unit. The weight must be
supported, uniformly across the bottom (fig. 3). To
remove the door, open the door and hold it all the
way open. Close the hinge latches (fig. 4) and
release the door. The door can then be removed by
gently lifting and pulling the door, with the hinges
up and out of the frame.
The professional range should be transported by a
dolly close to its final location. The range can be
tipped back and supported on the rear legs while
the dolly is removed. The floor under the legs
should be protected (Wood Strips, Carpet, Paneling,
etc.) before pushing the unit back into position.
Range Must
Must
be Range
Uniformly
be Uniformly
Supported
Supported
on on
Braces
Braces
22"
LevelingLegs
Legs
Leveling
Fig. 3
6
UNPACKING AND HANDLING
MOVING AND PLACING THE RANGE
Electric and gas connections should be made
before the range is slid into the cabinet opening
(see page 13 & 14). If installing a full backguard with
the range, it should also be installed before the
range is placed in its final position (refer to page 5).
For proper performance, the professional range
should be level. To achieve a flush fit of the range
to adjoining countertops, it will be necessary to
have level cabinets (front to back, and left to right
across opening of the range). After checking the
countertops for level and before sliding the range
into place, measure the distance from the floor to
the top of the counter work surface in the rear left
and right corners. Adjust the corresponding rear
corner of the range to an equal height of the
counter, as the rear leveling legs are not accessible
once the range is pushed into place. Once the
range is in place, the front leg levelers can be
accessed to level the front of the range. Replace
the kick panel and oven doors by reversing the
procedure described previously. It is important
that the two screws retaining the kick panel are
secure to prevent accidental access to live electrical
components and wires (fig. 1).
Lock
(close)
Unlock
Fig. 4
Shipping Screw
(remove)
GRIDDLE AND GRILL LEVEL ADJUSTMENTS
The grill and griddle sections (if equipped) are
fastened in place at the front with screws. They are
designed to be stationary and not meant to be
removed for cleaning. The griddle has two leveling
screws beneath the rear flue cover which can be
used to adjust the griddle to the desired slope. To
access the leveling adjustment screws, remove the
griddle flue cover by lifting upwards. The center
screw is for shipping and should be removed.
Outer Leveling
Screws (2)
Griddle Flue
Cover
Fig. 5
7
VENTILATION REQUIREMENTS
STEP 2:
A suitable exhaust hood must be installed above the range. The following chart indicates the
minimum blower capacity recommended for hood ventilation.
VENTILATION
UNIT
HOOD
STANDARD COUNTER
INSTALLATION
RECOMMENDATIONS
(24" Deep x Unit Width)
BLOWER
ISLAND
INSTALLATION
RECOMMENDATIONS
(30" Deep x 36" at Bottom)
*48" RANGE
800-1200 CFM
800-1200 CFM
**36" RANGE
600-1200 CFM
600-1200 CFM
30" RANGE
600 CFM
600 CFM
* When installing a unit featuring a grill, select a blower on the high end of recommendation.
** All 36” Range GL models require a 1200 CFM ventilation unit.
CAUTION:
Ventilation hoods and blowers are designed for use with single wall ducting.
However, some local building codes or inspectors may require double wall
ducting. Consult local building codes and/or local agencies, before starting, to
ensure that hood and duct installation will meet local requirements.
Hood blower speeds should be variable to reduce noise and loss of heated or air conditioned
household air when maximum ventilation is not required. Normally, the maximum blower speed is
only required when using the grill.
For best smoke elimination, the lower edge of the hood should be installed a minimum of 30" to a
maximum of 36" above the range cooking surface, (page 10 & 12). If the hood contains any
combustible materials (i.e. a wood covering) it must be a minimum of 36" above the cooking surface.
Due to a high volume of ventilation air, a source of outside replacement air is recommended. This is
particularly important for tightly sealed and insulated homes. A reputable heating and ventilating
contractor should be consulted.
8
INSTALLING ANTI - TIP DEVICE
All ranges must have an anti-tip device
correctly installed as per the following
instructions. If you pull the range out
from the wall for any reason, make sure
that the device is properly engaged
when you push the range back against
the wall. If it is not, there is a possible
risk of the range tipping over and
causing injury if you or a child stand, sit
or lean on an open oven door.
(2) Wood Screws into
Back Wall (ALL
Installations)
(2)Small Holes for
Wood Installations
(2) Large Holes for
Concrete Installations
BACK
WALL
INCLUDED PARTS:
Included with this kit are:
F
E O GE
D
I
S AN
HT R R
G
I
R LL O
WA
(4) #10 x 2” wood screws,
(1) Anti-tip bracket, and (1) Installation
Instructions.
A
INSTALLING THE KIT:
Instructions are provided for wood and
cement floors. Any other type of
construction may require special installation techniques as deemed necessary
to provide adequate fastening of the Antitip bracket to the floor and wall. The use of
this bracket does not preclude tipping of
the range when not properly installed.
Fig. 6
A=
1/4”
1/2”
5/8”
Model
Series
RDS-305
RDS-48
RDS-36
WOOD CONSTRUCTION:
Place the bracket against the back wall, into the right
rear corner where the range is to be located. Leave a
gap between the wall (or side of range) and the
bracket (see fig. 6). Drill (2) 1/8” diameter pilot holes
in the center of the small holes. A nail or awl may be
used if a drill is not available. Fasten the bracket
securely to the floor and wall.
CONCRETE OR CEMENT CONSTRUCTION:
Hardware Required:
WARNING
ALL RANGES CAN TIP
INJURY COULD RESULT
INSTALL ANTI-TIP
BRACKET PACKED
INSIDE OVEN
SEE INSTRUCTIONS
(2) sleeve anchors, lag bolts, and washers (not
provided). Locate the bracket as described above.
Fig. 7
Drill the recommended size holes for the hardware.
Install the sleeve anchors into the holes and then install the lag bolts through the bracket. The bolts
must be properly tightened as recommended for the hardware. Fasten the bracket securely to the
floor and wall.
ONCE INSTALLED:
Complete the range installation per the instructions provided with the product. Check for proper
installation of the range and Anti-tip device by grasping the back of the unit and carefully attempt to
tilt the range forward.
9
CABINET PREPARATION
STEP 3:
1) The range is a free standing unit. If the unit is to be placed adjacent to cabinets, the clearances
shown in fig. 8 (RDS-36 & 48) & fig. 9 (RDS-305) are required. The same clearances apply to island
installations.
2) The range can be placed in various positions with respect to the cabinet front, with the front either
flush or projecting, depending on the countertop depth.
3) The gas and electrical supply should be within the zones shown (fig. 8, 9, & 10).
4) The maximum depth of over head cabinets installed on either side of the hood is 13”.
5) Any openings in the wall behind the range and in the floor under the range must be sealed.
6) When there is less than a 12” clearance between combustible material and the back edge of the
range, (above the cooking surface) a DCS Low backguard or Full backguard must be installed, (fig.
11A ). When clearance to combustible material is over 12” no backguard is necessary (fig. 11B ).
These parts must be ordered separately. Fig. 11 indicate the space required for each type of
backguard.
7) Always keep the appliance area clear and free from combustible materials, gasoline and other
flammable vapors and liquids.
8) Do not obstruct the flow of combustion and ventilation air to the unit.
Min. 48" Wide Hood
Min. 36" Wide Hood
13"
Max.
12" Min. to combustible
material , each side
18"Min.
12"
A
A
B
cooking surface
3-1/4"
3-1/2"
Gas Supply
35-3/8" Max. For Level Counter,
36-3/4" Max. With Range
Leveling Legs Fully Extended
Electrical Supply
RDS 48 models
RDS 36 models
A B
8" 16"
4" 12"
As defined in the
“National Fuel Gas Code”
(ANSI Z223.1, Latest Edition).
The range height is adjustable. The level of the
range top must be at the same level or above the countertop level.
Fig. 8 RDS 36”/48” Models Only
10
CAUTION:
36" Min. to
combustible
material ,
from cooking
surface
CABINET PREPARATION
Min. 30" Wide Hood
(RDS 305 Models)
12" Min. to combustible
material , each side
18"Min.
7"
13"
Max
10-3/4" 2"
9"
CAUTION:
36" Min. to
combustible
material ,
from cooking
surface
cooking surface
4"
1-1/2" Electrical
Gas Supply (RDS)
Supply (RDS)
35-3/4" Max. For Level Counter,
37" Max. With Range
Leveling Legs Fully Extended
As defined in the
“National Fuel Gas Code”
(ANSI Z223.1, Latest Edition).
The range height is adjustable. The level of the
range top must be at the same level or above the countertop level.
Fig. 9 RDS-305 Models Only
Gas Supply
Manual Shut-Off
Valve must be
Easily Accessible
2" Maximum
Protrusion from Wall
for Gas Supply
Flex Line to Range
Electrical Supply
NEMA 14-50
Receptacle
Fig. 10 All RDS Models
11
CABINET PREPARATION
STANDARD INSTALLATION:
ISLAND INSTALLATION:
12" Min. to
Combustibles without backguard
G
36" Min. to
Combustibles H
A
C
B
C
0” Clearance
0” Clearance
E
F
J
D
I
As defined in the
“National Fuel Gas Code”
(ANSI Z223.1, Latest Edition).
The range height is adjustable. The level of the
range top must be at the same level or above the countertop level.
Fig. 11 All RDS Models Product / Installation Clearance Specifications
K
K
RDS-48 Models
RDS-36 Models
RDS-48 Models
RDS-36 Models
RDS-305 Models
A
28-1/8”
28-1/8”
28-1/8”
B
10-1/8”
10-1/8”
10-1/8”
C
2”
2”
2”
D
E
F
35-1/2” min.-37” max. 30-1/4” 44-1/2”
35-1/2” min.-37” max. 30-1/4” 44-1/2”
35-3/4” min.-37” max. 28-3/16” 43-7/8”
12
K
RDS-305 Models
G
H
I
J
K
28-1/4” 1-5/16” 25”
27-3/8” 47-7/8”
28-1/4” 1-5/16” 25”
27-3/8” 35-7/8”
27-3/8” 1-5/16” 24-3/16” 26-3/4” 29-7/8”
BACKGUARD INSTALLATION
BACKGUARD KITS:
Wall Mount
Full Backguard
The backguard is located as shown in Fig.
12. Secure the backguard to the wall
behind the range. Specific instructions for
installation of the full backguard or low
backguard can be found packaged
with the backguard. See also page 5,
“Planning The Installation” section.
A backguard must be installed when there
is less than a 12” clearance between
combustibles and the back of the range
(above the cooking surface). See fig. 11.
(Model #’s BGS-3030,
BGS-3036, BGS-3048)
Wall Mount
Low Backguard
(Model #’s BGS-1230,
BGS-1236, BGS-1248)
Fig. 12
ELECTRICAL / GAS CONNECTIONS
STEP 5:
ELECTRICAL CONNECTIONS
RDS-36 & 48 models
Always disconnect electric supply cord from the
wall outlet or service disconnect before servicing
this appliance. Observe all governing codes and
ordinances when grounding, in absence of
which, observe National Electrical Code ANSI /
NFPA No. 70-1990. The electrical supply must be
a 120/240 volt, 3 wire (plus ground) 60 Hz single
phase, 50 AMP circuit. The power receptacle
must be a NEMA 14-50 device to accept the four
prong plug supplied with the unit.The receptacle
should be located within the area shown in fig. 8,
page 10.
Valve must be
Easily Accessible
Electrical Supply
Electrical
Supply
m
from Wall
pply
NEMA
NEMA14-50
14-50
Receptacle
Receptacle
RDS-305 MODEL
The electrical supply must be a 120/240 volt, 3
wire (plus ground), 60 Hz, 30 AMP circuit. The
power receptacle must be a NEMA 14-50 device
to accept the four prong plug supplied with the unit.
The receptacle should be located within the area shown
in fig. 9, page 11.
13
Fig. 13
ELECTRICAL / GAS CONNECTIONS
STEP 5: (CONTINUED)
RECOMMENDED GROUNDING METHOD
This appliance is factory equipped with a power supply cord with a four-prong grounding plug. It
must be plugged into a mating grounding, type receptacle, connected to a correctly polarized 120/240
volt circuit. If the circuit does not have a grounding type receptacle, it is the responsibility and
obligation of the installer to have the existing receptacle changed to a properly grounded and
polarized receptacle in accordance with all applicable local codes and ordinances by a qualified
electrician. In the absence of local codes and ordinances, the receptacle replacement shall be in
accordance with the National Electrical Code.
THE FOURTH PRONG (ROUND GROUNDING PIN) SHOULD NOT, UNDER ANY
CIRCUMSTANCES, BE CUT OR REMOVED.
GAS REQUIREMENTS
Verify the type of gas supplied to the location. The range is shipped from the factory set up and
adjusted for natural gas or L.P. gas as specified by the customer order. If the range is not compatible
with gas supply, return it to the dealer.
NATURAL GAS
Connection: 1/2” N.P.T. Minimum 5/8” dia. flex line.
Pressure: 6” to 14”W.C.
LP GAS
Connection: 1/2” N.P.T. Minimum 5/8 dia. flex line.
Pressure: 11” to 14”W.C.
A regulator is required at the LP source to provide a maximum of 14”W.C. to the range regulator.
HOOK-UP TO GAS SUPPLY
STEP 6:
HOOK-UP
A manual valve must be installed external to the appliance, in an accessible location from the front for
the purpose of shutting off the gas supply. The supply line must not protrude beyond the back of the
unit. Make sure the gas supply is turned off at the wall valve before connecting the appliance.
The gas supply connections should be made by a qualified technician and in accordance with local
codes or ordinances. In the absence of a local code, the installation must conform to the National Fuel
Gas Code ANSI 223.1-1988, latest edition.
14
HOOK-UP TO GAS SUPPLY
STEP 6: (CONTINUED)
CAUTION:
The appliance must be isolated from the building’s gas supply piping system
by closing its individual manual shut-off valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than 1/2 psig
(3.5kPa.). The appliance and its individual shut-off valve must be disconnected
from the gas supply piping system during any pressure testing of the system at
the test pressures in excess of 1/2 psig (3.5kPa.).” When checking the manifold
gas pressure, the inlet pressure to the regulator should be at least 7.0” W.C. for
natural gas or 12.0” for LP.
NOTE: The flex line for the gas supply must be metal and be approved by an approved
certifying agency (AGA, CGA, or UL). Never use a hose made of rubber or other
synthetic material, as the heat may cause the hose to melt and develop leaks.
When hooking up the gas supply from
range rear hard pipe to wall hard pipe,
installation length of flex line between
range/wall hard piping must
accommodate range being pulled
from wall for cleaning or servicing
purposes. When range is pulled from
wall, no strain should occur at range or
wall hard pipe connections (fig. 14).
Manual Shut-Off
Valve must be
Easily Accessible
WALL
Hard Pipe
Connection
Hard Pipe
1/2" NPT
Metal Flex Gas Line
Fig. 14
15
TEST AND ADJUSTMENTS
STEP 7:
WARNING :
For Warranty coverage, DCS requires that burner adjustments be made by a
qualified technician at the time of installation. Extreme care should be u s e d
when adjustments are made after installation. Improper or lack of
adjustments will void your warranty.
Note: No air shutter adjustment is possible on the top burners. This adjustment section
applies to the griddle and grill burners.
Check for the proper burner flame characteristics and adjust air shutters if necessary (fig.
15). Each valve and air shutter is individually
tested and adjusted prior to shipment.
Normally adjustment is not required, however,
vibration during transit, gas conversion or
variations in the local gas supply may make
minor adjustments necessary. Burner flames
should be blue and stable with no yellow tips,
excessive noise or lifting of the flame from the
burner. If any of these conditions exist, check
that the air shutter or burner ports are not
blocked. If this condition persists, adjust the air
shutter as required. If the flame is too yellow,
indicating insufficient air, adjust the shutter
counterclockwise to increase air inlet. If the
flame is noisy or tends to lift away from the
burner, indicating too much air, turn the shutter
clockwise to reduce air. The griddle flames
should be 1-1/2" to 2". The grill burner flames
should be 3/8” to 5/8” (fig. 16).
Air Shutter
Fig. 15
Typical
Section
of Proper
Flame Flame
Typical
Section
of Proper
Griddle (Griddle)
Grill
1-1/2” -- 2”
1-1/2"
2"
(Grill)
3/8” - 5/8”
3/8"5/8"
If the top burner does not ignite, check the
spark igniter by listening for a clicking sound.
If you do not hear the igniter click, turn off the
burner. Check for a tripped circuit breaker,
blown fuse, or poor wire connection to the
igniter.
Fig. 16
TO CLEAN EXTERIOR SURFACES
The stainless steel surfaces may be cleaned by wiping with a damp soapy cloth. Any mild glass cleaner
will remove fingerprints and smears. Do not use steel wool as it will scratch this surface. Small
scratches may be removed by lightly sanding, with the grain, using 120 grit paper.
16
INSTALLER FINAL CHECKLIST
GENERAL
Placement of unit.
Specified clearance maintained to cabinet surfaces.
Unit Level - front to back, side to side.
All packaging material and tie straps removed, drip pans clean and empty.
Backguard attached if there is less than 12" clearance above the cooking surface to combustibles
behind unit.
Radiant tray placed in grill unit (if equipped). The two grill racks in place.
ELECTRICAL
Receptacle with 50 ampere over-current protection is provided for service cord connection.
Adequate ground connection.
Front kick panel in place and two (2) screws secure.
GAS SUPPLY
Connection: 1/2 NPT with a minimum 5/8" diameter flex line. Site gas supply is compatible with
range model, & sufficient pressure is available (see gas requirements pg. 14).
The pressure regulator which is connected to the manifold is set for 5.0 W.C. for natural gas or
10.0 W.C. for LP.
Manual gas shut-off valve installed in an accessible location.
Unit tested and free of gas leaks.
OPERATION
All internal packing materials removed. Check below grate, pans and drip drawers.
If used on LP gas, verify that pressure regulator, orifice hoods, air shutters, and valve jets have been
set for use with LP gas.
Bezels centered on burner knobs and knobs turn freely.
Each burner lights satisfactorily, both individually and with other burners.
Flame adjustment for 3/8” soft blue cone made on ports of each top burner, low flame adjustment
verified.
Griddle is level and does not rock (not all models).
Drip trays are properly in place and pull out freely (Not all models).
Oven door hinges seated and door opens and closes properly.
Burner grates correctly positioned, level, and do not rock.
17
RDS-48 WIRING DIAGRAM
17468-01.eps Rev.A 08/02
18
RDS-48 SCHEMATIC
17468-02.eps Rev.A 08/02
19
RDS-36 WIRING DIAGRAM
17469-01.eps Rev.A 08/02
20
RDS-36 SCHEMATIC
17469-02.eps Rev.A 08/02
21
RDS-485 WIRING DIAGRAM
17580-01.eps Rev.A 08/02
22
RDS-485 SCHEMATIC
17580-02.eps Rev.A 08/02
23
RDS-305 WIRING DIAGRAM
17470-01.eps Rev.A 08/02
24
RDS-305 SCHEMATIC
17470-02.eps Rev.A 08/02
25
HOW TO OBTAIN SERVICE
For warranty service, contact DCS Customer Service at (888) 281-5698. Before you call, please have
the following information ready:
Model Number
Serial Number
Date of installation
A brief description of the problem
Your satisfaction is of the utmost importance to us. If a problem cannot be resolved to your
satisfaction, please write or fax us at:
Write:
DCS
Attention: Consumer Relations
5800 Skylab Road
Huntington Beach, CA 92647
Fax us at: (714) 372-7004
email: support@dcsappliances.com
BEFORE YOU CALL FOR SERVICE:
1) Is the circuit breaker tipped or the fuse blown?
2) Is there a power outage in the area?
26
WARRANTY
Length of Warranty:
One (1) Year Full parts and Labor Covers the entire product.
Five (5) Year Surface burners, oven burner.
Ten (10) Year Porcelain oven, porcelain inner door panel. Oven racks and grates.
DCS Will Pay For
All repair labor and parts found to be defective due to materials or workmanship for one full year “IN
HOME” warranty during the first year of ownership. This does not apply if the unit was subjected to
other than normal household use. Service must be provided by Authorized Factory Agent during
normal working hours. No charges will be made for repair or replacement at the location of initial
installation or factory for parts returned pre-paid, through the dealer and claimed within the warranty
period, and found by DCS to be defective.
Replacement will be F.O.B. DCS, and DCS will not be liable for any transportation costs, labor costs, or
export duties. This warranty shall not apply, nor can we assume responsibility for damage that might
result from failure to follow manufactures instructions or local codes, where the appliance has been
tampered with or altered in anyway or which, in our judgement, has been subjected to misuse,
negligence, or accident. Implied warranty shall not extend beyond the duration of this written
warranty. This warranty is in lieu of all warranties expressed or implied and all other obligations or
liability in connection with the sale of this appliance.
DCS Will Not Pay For
Installation or start-up.
Shipping damage.
Service by an unauthorized agency.
Damage or repairs due to service by an unauthorized agency or the use of unauthorized parts.
Service during other than normal working hours.
Improper installation, such as improper hook-up, etc.
Service visits to teach you how to use the appliance; correct the installation; reset circuit
breakers or replace home fuses.
Repairs due to other than normal household use.
Damage caused from accident, abuse, alteration, misuse, incorrect installation or installation not
in accordance with local codes.
Units installed in non-residential application such as day care centers, bed and breakfast
centers, churches, nursing homes, restaurants, hotels, schools, etc.
This warranty applies to appliances used in residential applications; it does not cover use in
commercial situations. This warranty is for products purchased and retained in the 50 states of the
U.S.A., the District of Columbia and Canada. This warranty applies even if you should move during the
warranty period. Should the appliance be sold by the original purchaser during the warranty period,
the new owner continues to be protected until the expiration date of the original purchaser’s warranty
period. This warranty gives you specific legal rights. You may also have other rights which vary from
state to state.
27
NOTES
28
5800 Skylab Road, Huntington Beach, CA 92647
Tel: 714.372.7000 • Fax: 714.372.7001
Customer Service: (888) 281-5698
www.dcsappliances.com
As product improvement is an ongoing process at DCS, we
reserve the right to change specifications or design without
notice.
P/N 17435 Rev. B
Litho in USA 10/2002