Allied Telesis AT-FS201ST/FS3 Installation guide

AT-MC104XL
AT-MC104LH
AT-MC104SC/FS3, FS4
AT-MC104ST/FS3, FS4
Version 3 Fast Ethernet Media Converters
Installation Guide
PN 613-10781-00 Rev D
Copyright  2000 Allied Telesyn International, Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94086 USA
All rights reserved. No part of this publication may be reproduced without prior written
permission from Allied Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names,
company names, logos or other designations mentioned herein are trademarks or
registered trademarks of their respective owners.
Allied Telesyn International Corp. reserves the right to make changes in specifications
and other information contained in this document without prior written notice. The
information provided herein is subject to change without notice. In no event shall Allied
Telesyn be liable for any incidental, special, indirect, or consequential damages
whatsoever, including but not limited to lost profits, arising out of or related to this
manual or the information contained herein, even if Allied Telesyn International Corp.
has been advised of, known, or should have known, the possibility of such damages.
Safety Warnings
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Allied Telesyn International, Corp.
Manufacture Address:
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the Product:
Fast Ethernet Media Converters
Model Numbers:
AT-MC104XL, AT-MC104LH, AT-MC104SC/FS3,
AT-MC104ST/FS3, AT-MC104SC/FS4,
AT-MC104ST/FS4
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device must not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with instructions, may cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on; the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or registrant
of this equipment can void your authority to operate this equipment under Federal
Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
RFI Emission
EN55022 Class B ! 1
Immunity
EN50082-1 1997 ! 2
Electrical Safety
TUV-EN60950, UL1950, CSA 950
Laser
EN60825 ! 4
Power to the hub must be sourced only from the adapter.
!3
!9
USA/CANADA
Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA.
iii
EUROPE - EU
Use TÜV licensed AC adapter of DC 12V, 500mA.
UK
Use a UK Safety Approved AC adapter of DC 12V, minimum 500mA.
Important: Appendix A contains translated safety statements for installing this
equipment. When you see the !, go to Appendix A for the translated safety statement in
your language.
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses
Geräts. Wenn Sie ! sehen, schlagen Sie in Anhang A den übersetzten
Sicherheitshinweis in Ihrer Sprache nach.
Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af
dette udstyr. Når De ser symbolet !, skal De slå op i tillæg A og finde de oversatte
sikkerhedsadvarsler i Deres eget sprog.
Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van
deze apparatuur. Wanneer u de ! ziet, raadpleeg Appendix A voor vertaalde
veiligheidsinstructies in uw taal.
Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet
équipement. Lorsque vous voyez le symbole !, reportez-vous à l'annexe A pour consulter
la traduction de ces instructions dans votre langue.
Tärkeää: Liite A sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet.
Kun näe !-symbolin, katso käännettyä turvaohjetta liitteestä A.
Importante: l’Appendice A contiene avvisi di sicurezza tradotti per l’installazione di
questa apparecchiatura. Il simbolo !, indica di consultare l’Appendice A per l’avviso di
sicurezza nella propria lingua.
Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon for installering av dette
utstyret. Når du ser !, åpner du til Tillegg A for å finne den oversatte
sikkerhetsinformasjonen på ønsket språk.
Importante: O Anexo A contém advertências de segurança traduzidas para instalar este
equipamento. Quando vir o símbolo !, leia a advertência de segurança traduzida no seu
idioma no Anexo A.
Importante: El Apéndice A contiene mensajes de seguridad traducidos para la
instalación de este equipo. Cuando vea el símbolo !, vaya al Apéndice A para ver el
mensaje de seguridad traducido a su idioma.
Obs! Bilaga A innehåller översatta säkerhetsmeddelanden avseende installationen av
denna utrustning. När du ser !, skall du gå till Bilaga A för att läsa det översatta
säkerhetsmeddelandet på ditt språk.
iv
Table of Contents
Safety Warnings ............................................................................................ iii
Welcome to Allied Telesyn ......................................................................... vii
Where to Find Web-based Guides ................................................................... vii
Document Conventions .................................................................................... vii
Contacting Allied Telesyn Technical Support................................................ viii
Online Support ......................................................................................... viii
Telephone and Fax Support..................................................................... viii
E-mail Support ......................................................................................... viii
Returning Products ........................................................................................... ix
FTP Server ......................................................................................................... ix
For Sales or Corporate Information .................................................................. x
Tell Us What You Think .................................................................................... x
AT-MC104 Series Fast Ethernet Media Converters ............................... 1
Key Features....................................................................................................... 2
Status LEDs ................................................................................................ 3
Link Test/MissingLink Button ................................................................... 3
External AC/DC Power Adapter................................................................. 4
Network Topologies ............................................................................................ 5
Installing the Media Converter ......................................................................... 6
Planning the Installation............................................................................ 6
Cable Specifications .................................................................................... 7
Verifying the Package Contents ................................................................. 9
Reviewing Safety Precautions .................................................................... 9
Installing the Media Converter ................................................................ 10
Testing the Installation ............................................................................ 11
Warranty Registration ..................................................................................... 13
Technical Specifications ................................................................................... 13
Physical Specifications.............................................................................. 13
Agency Certifications ................................................................................ 13
Power Requirements ................................................................................. 13
Single-mode Port Specifications ............................................................... 14
Multimode Port Specifications (All Models) ............................................ 16
v
Appendix A
Translated Safety Statements ................................................................... 19
Appendix B
AT-MC104 Series Installation Guide Feedback .................................... 29
Appendix C
Technical Support Fax Order ................................................................... 31
vi
Welcome to Allied Telesyn
This guide contains instructions on how to install an AT-MC104 Series Fast
Ethernet Media Converter.
Where to Find Web-based Guides
The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation and technical information
for all of our products. For product guides, you can go directly to the following
web page: www.alliedtelesyn.com/support/prd_libs.htm.
Document Conventions
This guide uses several conventions that you should become familiar with first
before you begin to install the product.
Note
A note provides additional information.
Caution
A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.
Warning
A warning indicates that performing or omitting a specific action may
result in bodily injury.
vii
Contacting Allied Telesyn Technical Support
There are several ways to contact Allied Telesyn technical support: online,
telephone, fax or e-mail.
Online Support
You can request technical support online by filling out the Technical Support
Form at www.alliedtelesyn.com/forms/support.htm.
Telephone and Fax Support
Americas
United States, Canada, Mexico,
Central America, South America
Tel: 1 (800) 428-4835, option 4
Fax: 1 (503) 639-317 6
Germany
Germany, Switzerland, Austria, Eastern
Europe
Tel: (+49) 0130/83-56-66
Fax: (+49) 30-435-900-115
Asia
Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: (+65) 381-5612
Fax: (+65) 383-3830
Italy
Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: (+39) 02-416047
Fax: (+39) 02-419282
Australia
Tel: 1 (800) 000-880
Fax: (+61) 2-9438-4966
Japan
Tel: (+81) 3-3443-5640
Fax: (+81) 3-3443-2443
France
France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: (+33) 0-1-60-92-15-25
Fax: (+33) 0-1-69-28-37-49
United Kingdom
United Kingdom, Denmark, Norway,
Sweden, Finland
Tel: (+0044) 1235-442500
Fax: (+44) 1-235-442680
E-mail Support
United States and Canada
TS1@alliedtelesyn.com
Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands
latin_america@alliedtelesyn.com
United Kingdom, Sweden, Norway, Denmark, and Finland
support_europe@alliedtelesyn.com
viii
AT-MC104 Series Installation Guide
Returning Products
Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.
To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:
North America
2205 Ringwood Ave
San Jose, CA 95131
Tel: 1-800-428-4835, option 4
Fax: 1-503-639-3716
European Customer Support Centre
10/11 Bridgemead Close
Westmead Industrial Estate
Swindon, Wiltshire SN5 7YT
England
Tel: +44-1793-501401
Fax: +44-1793-431099
Latin America, the Caribbean,
Virgin Islands
Tel: international code + 425-481-3852
Fax: international code + 425-483-9458
Mexico and Puerto Rico
Tel: 1-800-424-5012, ext 3852 or
1-800-424-4284, ext 3852
Mexico only: 95-800-424-5012, ext 3852
Fax: international code + 425-489-9191
FTP Server
If you know the name of a specific driver that you need for an Allied Telesyn
device, you can download the software by connecting directly to our FTP
server at: ftp://gateway.centre.com.
At login, enter ‘anonymous’. Enter your e-mail address for the password as
requested by the server at login.
ix
For Sales or Corporate Information
Allied Telesyn International, Corp.
19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: 1 (425) 487-8880
Fax: 1 (425) 489-9191
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: 1 (800) 424-4284 (USA and Canada)
Fax: 1 (408) 736-0100
Tell Us What You Think
If you have comments or suggestions to improve this or other Allied Telesyn
documents, please fill out the “AT-MC104 Series Installation Guide Feedback”
on page 29 and return the form to us at the address or fax number provided.
You can also provide feedback online by filling out the Send Us Feedback
Form at www.alliedtelesyn.com/forms/feedback.htm.
x
AT-MC104 Series Fast Ethernet Media
Converters
The AT-MC104 Series Media Converters include the following models:
❑ AT-MC104XL
❑ AT-MC104ST/FS3
❑ AT-MC104LH
❑ AT-MC104SC/FS4
❑ AT-MC104SC/FS3
❑ AT-MC104ST/FS4
AT-MC104 Series Fast Ethernet Media Converters are designed to extend the
distance of your network by interconnecting multimode fiber optic cabling and
single-mode fiber optic cabling. The media converters allow you to
interconnect LAN devices that are physically separated by large distances.
Each media converter features two 100Base-FX ports with either SC or ST
connectors. One port uses multimode fiber optic cabling and has a maximum
distance of 2 kilometers (1.2 miles). The second port uses single-mode fiber
optic cabling and has a maximum distance of 15 kilometers (9.3 miles) to 100
kilometers (62 miles), depending on the model. These units operate at 100
Mbps and feature half-duplex and full-duplex operation.
The media converters can be installed either as standalone units, such as on a
table, or in an AT-MCR12 Rackmount Chassis or AT-TRAY4 Rackmount Tray.
AT-MC104 Series Media Converters are easy to install and do not require any
software configuration or management. Figure 1 shows an AT-MC104 Series
Media Converter.
CLASS 1
LASER LIGHT
DO NOT STARE
INTO BEAM
TX
RX
M/L
ON
100Base-FX
TX
RX
100Base-FX
LNK
LNK
PWR
ACT
LNK TST
ACT
SINGLE MODE
M/L ON
MULTI MODE
MC104XL SINGLE MODE / MULTI MODE FIBER FAST ETHERNET MEDIA CONVERTER
Figure 1 AT-MC104 Series Media Converter (AT-MC104XL model)
1
Table 1 list the maximum cabling distances for each model.
Table 1 Maximum Operating Distances
Type of Connector
Model
Maximum Distance1
Port 1
(Single-mode)
Port 2
(Multimode)
Port 1
(Single-mode)
Port 2
(Multimode)
AT-MC104XL
SC
SC
15 km (9.3 mi)
2 km (1.2 mi)
AT-MC104LH
SC
SC
40 km (24.8 mi)
2 km (1.2 mi)
AT-MC104SC/FS3 SC
SC
75 km (46.5 mi)
2 km (1.2 mi)
AT-MC104ST/FS3 ST
ST
75 km (46.5 mi)
2 km (1.2 mi)
AT-MC104SC/FS4 SC
SC
100 km (62 mi)
2 km (1.2 mi)
AT-MC104ST/FS4 ST
ST
100 km (62 mi)
2 km (1.2 mi)
1. Maximum distance may be less depending on the duplex mode of the end stations and the type of fiber optic
cabling used with the port.
Key Features
The media converters have the following key features:
2
❑
LEDs for unit and port status
❑
Two 100Base-FX fiber optic ports
❑
Link Test/MissingLink button for performing a link test on the fiber
ports and notifies node of connection failures
❑
Half- or full-duplex operation
❑
External AC/DC power adapter
❑
Standard size for use with an AT-MCR12 chassis or AT-TRAY4 tray
AT-MC104 Series Installation Guide
Status LEDs
Table 2 defines the system LEDs.
Table 2 Status LEDs
LED
State
Color
Description
LNK
ON
Green
Link is established on the port.
ACT
ON
Green
Data is being received on the port.
PWR
ON
Green
Power is applied.
M/L ON
ON
Green
The MissingLink feature is activated on the media
converter.
OFF
The MissingLink feature is disabled and the unit is
operating in the link test mode.
Link Test/MissingLink Button
The Link Test/MissingLink button allows you to perform a link test on the
ports on the media converter. This button also allows you to activate the
MissingLink feature on the unit. Both features are describe in the following
section.
Link Test. The link test is a fast and easy way for you to test the connections
between the ports on the media converter and the nodes that are connected to
the ports. If a network problem occurs, you can perform a link test to determine
which port is experiencing a problem, and be able to focus on the fiber optic
cable and node where the problem resides.
A link test is performed when the button is in the LNK TST (OUT) position. For
instructions on performing a link test, refer to “Testing the Installation” on
page 11.
Note
Performing a link test does not interfere with a media converter’s ability
to pass network traffic.
3
MissingLink. The MissingLink feature activates the fiber optic ports on the
media converter to pass the “Link” status of their connections to each other.
When the media converter detects a problem with one of the ports, such as the
loss of connection to a node, the media converter shuts down the connection to
the other port, thus notifying the node that the connection has been lost.
For example, if the fiber optic cable connected to the multimode port on the
media converter were to fail, the unit would respond by dropping the link on
the single-mode port. In this way, the media converter notifies the end node
connected to the single-mode port that the connection on the other port has
been lost. If the failure had started on the single-mode port, the unit would drop
the connection to the multimode port.
The value to this type of network monitoring and fault notification is that some
hubs and switches can be configured to take a specific action in the event of the
loss of connection on a port. In some cases, the unit can be configured to seek a
redundant path to a disconnected node or send out a trap to a network
management station, and so alert the network administrator of the problem.
Note
The MissingLink feature is disabled when you perform a link test.
Consequently, to ensure that the MissingLink feature is enabled on the
media converter, always set the Link Test/MissingLink button to the
M/L ON (IN) position during normal network operations.
External AC/DC Power Adapter
The power adapter supplies 12 volts DC to the media converter. Allied Telesyn
supplies an approved safety compliant AC power adapter for the 120 and 240
V AC versions with an unregulated output of 12 VDC at 1A.
Figure 2 External AC/DC Power Adapter (North American version)
4
AT-MC104 Series Installation Guide
Network Topologies
Figure 3 shows two typical network configurations of the media converter.
10/100Base-TX Switch
AT-MC103XL
AT-MC104XL
100 meters
CLASS 1
LASER PRODUCT
DO NOT STARE
INTO BEAM
TX
M/L
ON
RX
15 kilometers/
49,213 ft (9.3 mi)
100Base-FX 100Base-TX
FDX
LNK
A/N ON
MDI
ACT
A/N OFF
MDI-X
CLASS 1
LASER LIGHT
DO NOT STARE
INTO BEAM
TX
RX
M/L
ON
100Base-FX
TX
RX
100Base-FX
LNK
LNK
LNK
PWR
PWR
ACT
LNK TST
ACT
M/L ON
ACT
LNK TST
SINGLE MODE
MC103XL SINGLE MODE FIBER FAST ETHERNET MEDIA CONVERTER
SINGLE MODE
M/L ON
MULTI MODE
MC104XL SINGLE MODE / MULTI MODE FIBER FAST ETHERNET MEDIA CONVERTER
2 kilometers/
6,562 ft
10/100Base-TX/FX Switch
10/100Base-TX/FX Switch
AT-MC104XL
2 kilometers/
6,562 ft
CLASS 1
LASER LIGHT
DO NOT STARE
INTO BEAM
TX
RX
M/L
ON
100Base-FX
TX
RX
AT-MC104XL
15 kilometers/
49,213 ft (9.3 mi)
100Base-FX
LNK
LNK
CLASS 1
LASER LIGHT
DO NOT STARE
INTO BEAM
TX
RX
M/L
ON
TX
RX
100Base-FX
LNK
PWR
ACT
ACT
SINGLE MODE
100Base-FX
LNK
PWR
ACT
LNK TST
M/L ON
MULTI MODE
MC104XL SINGLE MODE / MULTI MODE FIBER FAST ETHERNET MEDIA CONVERTER
LNK TST
ACT
SINGLE MODE
M/L ON
MULTI MODE
MC104XL SINGLE MODE / MULTI MODE FIBER FAST ETHERNET MEDIA CONVERTER
2 kilometers/
6,562 ft
Cable Legend
Twisted Pair
Single-mode Fiber
10/100Base-TX/FX Switch
Multimode Fiber
Figure 3 Typical Configurations
5
Installing the Media Converter
The following sections explain how to install the media converter. The media
converter can be installed either as a standalone unit (such as on a table) or in
an AT-MCR12 chassis or an AT-TRAY4 tray.
Planning the Installation
Be sure to observe the following guidelines when planning the installation of
your media converter.
6
❑
The nodes connected to the media converter must operate at 100
Mbps.
❑
The two nodes connected to the ports of the media converter must
operate with the same duplex mode, either half- or full-duplex. The
media converter itself can operate in either mode.
❑
The devices connected to the two ports on the media converter can be
network adapter cards, repeaters, switches, or routers.
❑
Be sure to observe the appropriate cabling specifications. Refer to
“Cable Specifications” on page 7.
AT-MC104 Series Installation Guide
Cable Specifications
Table 3, Table 4, and Table 5 list the IEEE 802.3u cabling specifications for the
AT-MC104 Series Media Converter.
Table 3 Multimode Port Specifications
Cable Type
50/125 or 62.5/125 micron multimode fiber
Maximum Distance
2 km (1.2 mi)
Table 4 Single-mode Port Specifications (Full-duplex)
Media Converter
Type of Fiber Optic Cable
AT-MC104XL
50/125 or 62.5/125
micron multimode
AT-MC104LH
Maximum
Distance
Maximum
Allowable Loss
Budget
2 km (1.2 mi)
20 dB at 1310 nm
9/125 micron single-mode 15 km (9.3 mi)
13 dB at 1310 nm
50/125 or 62.5/125
micron multimode
20 dB at 1310 nm
2 km (1.2 mi)
9/125 micron single-mode 40 km (24.8 mi)
18 dB at 1310 nm
AT-MC104SC/FS3
9/125 micron single-mode 75 km (46.5 mi)1
33 dB at 1310 nm
AT-MC104ST/FS3
9/125 micron single-mode 75 km (46.5 mi)1
33 dB at 1310 nm
AT-MC104SC/FS4
9/125 micron single-mode 100 km (62 mi)2
34 dB at 1550 nm
AT-MC104ST/FS4
9/125 micron single-mode 100 km (62 mi)2
34 dB at 1550 nm
1. The port has a minimum operating distance of 15 km (9.4 mi). This is to prevent blinding or burning out the
optical receiver on the far-end node.
2. The port has a minimum operating distance of 40 km (24.8 mi). This is to prevent blinding or burning out
the optical receiver on the far-end node.
7
Table 5 Single-mode Port Specifications (Half-duplex)1
Number of Media Converters
One Media Converter Inline
Two Media Converters Inline
Connected Devices
Maximum Distance
Switch to switch
372 m (1,221 ft)
Workstation to switch
372 m (1,221 ft)
Switch to Class I repeater
137 m (450 ft)
Switch to Class II repeater
185 m (607 ft)
Switch to switch
332 m (1,089 ft)
Workstation to switch
322 m (1, 089 ft)
Switch to Class I repeater
97 m (318 ft)
Switch to Class II repeater
145 m (476 ft)
1. The total distance of the fiber optic lengths cannot exceed the limits stated in the table. Each media converter
used inline within a single collision domain reduces the overall segment length by 40 m (131 ft).
Note
For additional technical information on the media converter’s fiber optic
ports, refer to “Technical Specifications” on page 13.
8
AT-MC104 Series Installation Guide
Verifying the Package Contents
Make sure the following items are included in your media converter package.
If any of the following items are missing or damaged, contact your sales
representative.
❑
One AT-MC104 Series Fast Ethernet Media Converter
❑
Four protective feet (for standalone use only)
❑
External AC/DC power adapter
❑
This installation guide
❑
Warranty card
Reviewing Safety Precautions
Please review the following safety precautions before you begin to install the
media converter.
Warning
Class 1 laser product. ! 5
Warning
Do not stare into the laser beam. ! 6
Warning
Lightning Danger: Do not work on equipment or cables during periods
of lightening activity. ! 7
Caution
Do not block air vents. ! 8
Caution
Power to the hub must be sourced only from the adapter. ! 9
Caution
Operating Temperature
This product is designed for a maximum ambient temperature of 40
degrees C. ! 10
Caution
All Countries: Install product in accordance with local and National
Electrical Codes. ! 11
9
Installing the Media Converter
The following procedure explains how to install the media converter.
If you are building a back-to-back installation, please review the following. See
Figure 3 for an illustration of a back-to-back-media converter configuration.
❑
During installation, setup, and testing of back-to-back media
converters, make sure each media converters Link Test/MissingLink
button is in the LNK TST (OUT) position.
❑
When two media converters are connected back-to-back with no UTP/
STP cables connected and when the LNK TST button is in the OUT
position (link test mode), the ACT LEDs on each converter may flash.
This is normal and will not affect the normal operation of the
converters.
To install the unit, perform the following procedure:
1.
Remove all equipment from the package and store the packaging material
in a safe place.
2.
If you are installing the unit on a desktop, attach the four rubber feet to
the base of the unit, placing one rubber foot in each corner. If you are
installing the unit in an AT-MCR12 chassis or AT-TRAY4 tray, do not
attach the rubber feet.
3.
Set the Link Test/MissingLink button to LNK TST (OUT) position.
4.
If you are installing the unit in an AT-MCR12 chassis or AT-TRAY4 tray,
refer to the appropriate installation guide for instructions on how to
install the media converter into the unit.
5.
Plug the AC/DC power adapter into an appropriate AC power outlet and
inset the power plug into the DC receptacle located on the rear panel.
(This step does not apply if you installed the unit in an AT-MCR12
chassis.)
12 V D C
Figure 4 12V DC Connector on Rear Panel with External Power Adapter
6.
10
Verify that the Power LED is green.
AT-MC104 Series Installation Guide
7.
Remove the dust covers from the fiber optic connectors.
8.
Connect the fiber optic cables to their respective ports on the media
converter.
9.
Connect the other end of the fiber cable to the desired end station.
Note
End stations used with the media converter must operate with the same
duplex mode (either both full-duplex or both half-duplex).
Go to “Testing the Installation” on page 11 for instructions on how to test the
unit.
Testing the Installation
This procedure explains how to test the media converter by performing a link
test. A link test will determine whether each port on the media converter is
successfully receiving a signal from the node connected to it. You should
perform this test immediately after you have installed the media converter or
whenever you are experiencing a problem with the unit. To perform a link test,
perform these steps:
1.
Verify that the Power LED on the media converter is green. If the LED is
OFF, check the following:
— If installed as a standalone unit, check to be sure that the adapter cable
is securely connected to the back of the media converter and that the
power adapter is securely connected to a power outlet.
— If installed in an AT-MCR12 chassis, check that the unit is fully seated
in the slot.
— Verify that the power outlet has power by connecting another device to
it.
— Try using another power adapter.
2.
Turn ON the nodes (such as the hubs or switches) that are connected to
the ports on the media converter.
3.
Set the Link Test/MissingLink button on the media converter to the LNK
TST (OUT) position.
11
4.
Check the two LNK LEDs. They should be green, indicating that the
media converter is receiving a signal from the nodes connected to the
ports. If a LNK LED is not green, check the following:
— The node connected to the port is powered ON.
— The fiber optic cable is securely connected to the fiber optic port.
— The appropriate type of fiber optic cable for the port is being used. Refer
to Table 3 through Table 5 for cable specifications.
— The maximum allowable loss budget for the fiber optic cable has not
been exceeded.
5.
If the two LNK LEDs are green but there is a communication problem
between the nodes connected to the media converter (and you are not
running a link test), check the following:
— The nodes connected to the ports are operating at 100 Mbps.
— The nodes connected to the media converter are operating in the same
duplex mode. The media converter is transparent to the duplex mode.
— The Link Test/MissingLink button on the media converter is in the
M/L ON (IN) position.
— Check that the maximum allowable loss budget for the fiber optic cable
has not been exceeded.
6.
Set the Link Test/MissingLink button on the media converter to M/L ON
(IN) position. The M/L ON position activates the MissingLink feature on
the media converter.
Note
When operating two media converters in a back-to-back configuration, it
is recommended that the MissingLink feature on one or both of the
converters be disabled. The MissingLink feature can be disabled by
placing the LNK TST to the OUT position. Disabling the MissingLink
feature does not interfere with the converter’s ability to pass network
traffic.
If you are still experiencing problems after testing the installation, contact
Allied Telesyn Technical Support. Technical support is offered online,
telephone, fax or e-mail.
Refer to “Contacting Allied Telesyn Technical Support” on page viii or visit our
web site at www.alliedtelesyn.com for support information.
12
AT-MC104 Series Installation Guide
Warranty Registration
When you finish the installation, register your product by completing the
enclosed warranty card and sending it in. You can also visit our web site at
www.alliedtelesyn.com/forms/warranty.htm and fill out the registration
online.
Technical Specifications
Physical Specifications
Dimensions:
WxDxH
10.5 cm x 9.5 cm x 2.5 cm
(4.125 in x 3.75 in x 1.0 in)
Maximum Operating
Temperature:
0o C to 40o C (32o F to 104o F)
Maximum Storage
Temperature:
-20o C to 60o C (-4o F to 140o F)
Operating Altitude:
Up to 3,048 meters (10,000 feet)
Humidity:
5% to 95% (non-condensing)
Agency Certifications
EMI/RFI:
FCC Class B, EN55022 Class B,
VCCI Class B
Safety:
UL 1950, CSA 22.2 No. 950,
TUV (EN60950), CE Compliant
Immunity:
EN50082-1 1997 Immunity Standard
Power Requirements
Input Supply Voltage:
12 V DC ± 5%
Maximum Current:
500 mA
Power Consumption:
6W
13
Single-mode Port Specifications
Table 6 Fiber Optic Transmitter
Launch Power (dBm)2
Fiber
Type1
Fiber Optic
Diameter
(microns)
AT-MC104XL
SMF
9/125
1310 nm
-8.0
-11.5
-15.0
AT-MC104LH
SMF
9/125
1310 nm
0.0
-3.0
-5.0
AT-MC104SC/FS3
and
AT-MC104ST/FS3
SMF
9/125
1310 nm
0.0
-2.0
-4.0
AT-MC104SC/FS4
and
AT-MC104ST/FS4
SMF
9/125
1550 nm
0.0
-1.5
-3.0
Model
Optical
Frequency
Max.
Avg.
Min.
1. SMF = Single-mode Fiber
2. The launch power measured at one meter from the transmitter
Table 7 Fiber Optic Receiver
Receive Power (dBm)
Fiber
Type1
Fiber
Optic
Diameter
(microns)
Optical
Frequency
AT-MC104XL
SMF
9/125
1310 nm
AT-MC104LH
SMF
9/125
AT-MC104SC/FS3
and
AT-MC104ST/FS3
SMF
AT-MC104SC/FS4
and
AT-MC104ST/FS4
SMF
Model
1. SMF = Single-mode Fiber
14
Min.
Typical
Saturation
-31.0
-31.0
-8.0
1310 nm
-35.0
-38.0
0.0
9/125
1310 nm
-37.0
-37.0
-3.0
9/125
1550 nm
-37.0
-37.0
-3.0
AT-MC104 Series Installation Guide
Table 8 Fiber Optic Datalink
Model
Fiber
Optic
Diameter
(microns)
Optical
Freq.
Min.
Power/
Link
Budget
(dB)
Avg.
Signal
Loss
(dB)
Min.
Distance
Spec.1
Max.
Distance
Spec.
(Full-duplex
only)
AT-MC104XL
9/125
1310 nm
16.0
19.50
0
15 km
(9.3 mi)
AT-MC104LH
9/125
1310 nm
30.0
35.00
0
40 km
(24.8 mi)
AT-MC104SC/FS3 9/125
and
AT-MC104ST/FS3
1310 nm
33.0
35.00
15 km
(9.3 mi)
75 km
(46.5 mi)
AT-MC104SC/FS4 9/125
and
AT-MC104ST/FS4
1550 nm
34.0
35.50
40 km
(24.8 mi)
100 km
(62 mi)
1. The launch power measured at one meter from the transmitter
Table 9 Fiber Optic Loss Specifications (Benchmarks)
Fiber Type1
SMF
Fiber Optic
Diameter
(microns)
Optical
Frequency
Typical Loss
Factor
(dB/km)
Worst Case
Loss Factor
(dB/km)
9/125
1310 nm
0.40
1.00
9/125
1550 nm
0.30
0.75
1. SMF = Single-mode Fiber
15
Multimode Port Specifications (All Models)
Table 10 Fiber Optic Transmitter
Fiber Optic
Diameter
(microns)
Fiber Type1
Optical
Frequency
Launch Power (dBm)2
Maximum
Average
Minimum
MMF
50/125
1310 nm
-14.0
-20.3
-22.5
MMF
62.5/125
1310 nm
-14.0
-16.8
-19.0
1. MMF = Multimode Fiber
2. Launch power measured at one meter from the transmitter.
Table 11 Fiber Optic Receiver
Fiber Optic
Diameter
(microns)
Fiber Type1
Optical
Frequency
Receive Power (dBm)
Minimum
Typical
Saturation
MMF
50/125
1310 nm
-31.8
-34.5
-14.0
MMF
62.5/125
1310 nm
-31.8
-34.5
-14.0
1. MMF = Multimode Fiber
Table 12 Fiber Optic Datalink
Maximum
Distance
Specs
(Full-duplex
only)
Optical
Frequency
Minimum
Power/
Link
Budget
(dB)
Average
Signal
Loss (dB)
Minimum
Distance
Specs2
50/125
1310 nm
13.00
18.70
0
2 km (1.2 mi)
62.5/125
1310 nm
16.80
22.50
0
2 km (1.2 mi)
Fiber
Type1
Fiber
Optic
Diameter
(microns)
MMF
MMF
1. MMF = Multimode Fiber
2. In all cases where the maximum transmitter output power exceeds the receivers sensitivity, a recommended
minimum ranges is stated. This is to prevent blinding or burning out the optical receiver on the far-end
node.
16
AT-MC104 Series Installation Guide
Table 13 Fiber Optic Loss Specifications (Benchmarks)
Fiber
Type1
MMF
Fiber Optic
Diameter
(microns)
Optical
Frequency
Typical Loss
Factor (dB/km)
50/125
850 nm
3.00
3.50
400
62.5/125
850 nm
3.00
3.75
200
100/140
850 nm
4.00
4.00
100
50/125
1310 nm
1.00
1.50
400
62.5/125
1310 nm
1.00
1.50
500
Worst Case
Loss Factor
(dB/km)
Bandwidth
(Mhz/km)
17
Appendix A
Translated Safety Statements
Important: This appendix contains multiple-language translations for the
safety statements in this guide.
Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.
Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.
Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.
Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.
Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.
Importante: questa appendice contiene traduzioni in più lingue degli avvisi
di sicurezza di questa guida.
Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.
Importante: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.
Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.
Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.
19
Standards: This product meets the following standards.
U.S. Federal Communications Commission
DECLARATION OF CONFORMITY
Manufacture Name:
Manufacture Address:
Allied Telesyn International, Corp.
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
Manufacture Telephone:
408-730-0950
Declares that the Product:
Fast Ethernet Media Converters
Model Numbers:
AT-MC104XL, AT-MC104LH, AT-MC104SC/FS3,
AT-MC104ST/FS3, AT-MC104SC/FS4,
AT-MC104ST/FS4
This product complies with FCC Part 15B, Class B Limits:
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device must not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with instructions,
may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on; the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes and modifications not expressly approved by the manufacturer or
registrant of this equipment can void your authority to operate this equipment
under Federal Communications Commission rules.
Industry Canada
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.
!1
RFI Emission
EN55022 Class B
!2
Immunity
EN50082-1 1997
!3
Electrical Safety
EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Warning Class 1 Laser product.
!6
Warning Do not stare into the Laser beam.
20
AT-MC104 Series Installation Guide
At time of installation, the Fiber Optic Lasers comply with FDA Radiation
Performance Standard 21CFR Subchapter J, applicable at date of manufacture. Use
of controls or adjustments of performance or procedures other than those specified
herein may result in hazardous radiation exposure.
SAFETY
!7
LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during periods of
LIGHTNING ACTIVITY.
!8
DO NOT BLOCK AIR VENTS
!9
Power to the hub must be sourced only from the adapter.
USA/CANADA
Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA.
EUROPE - EU
Use TÜV licensed AC adapter of DC 12V, 500mA.
UK
Use a UK Safety Approved AC adapter of DC 12V, minimum 500mA.
! 10
OPERATING TEMPERATURE
This product is designed for a maximum ambient temperature of 40 degrees C.
! 11
ALL COUNTRIES: Install product in accordance with local and National Electrical
Codes.
Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.
!1
Hochfrequenzstörung
EN55022 Klasse B
!2
Störsicherheit
EN50082-1 1997
!3
Elektrische Sicherheit
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Warnung Laserprodukt der Klasse 1.
!6
Warnung Nicht direkt in den Strahl blicken.
SICHERHEIT
!7
GEFAHR DURCH BLITZSCHLAG
GEFAHR: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen
!8
ENTLÜFTUNGSÖFFNUNGEN NICHT VERSPERREN
!9
Der Buchse darf nur aus dem Adapter Strom zugeführt werden.
EUROPE - EU
Gebrauchen Sie einen von TÜV zugelassenen Wechselstromadapter für Gleichstrom
12 V, 500 mA.
21
! 10
BETRIEBSTEMPERATUR
Dieses Produkt wurde für den Betrieb in einer Umgebungstemperatur von nicht
mehr als 40° C entworfen.
! 11
ALLE LÄNDER: Installation muß örtlichen und nationalen elektrischen
Vorschriften entsprechen.
Standarder: Dette produkt tilfredsstiller de følgende standarder.
!1
Radiofrekvens forstyrrelsesemission
EN55022 Klasse B
!2
Immunitet
EN50082-1 1997
!3
Elektrisk sikkerhed
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Advarsel Laserprodukt av klasse 1.
!6
Advarsel Stirr ikke på strålen.
SIKKERHED
!7
FARE UNDER UVEJR
FARE: UNDLAD at arbejde på udstyr eller KABLER i perioder med
LYNAKTIVITET.
!8
VENTILATIONSÅBNINGERNE MÅ IKKE BLOKERES
!9
Strømforsyningen til apparatet må udelukkende tages fra
tilpasningstransformatoren.
EUROPE - EU
Brug kun TÜV godkendt vekselstrømstransformator på 12 V jævnstrøm, 500 mA.
! 10
BETJENINGSTEMPERATUR
Dette apparat er konstrueret til en omgivende temperatur på maksimum 40 grader
C.
! 11
ALLE LANDE: Installation af produktet skal ske i overensstemmelse med lokal og
national lovgivning for elektriske installationer.
Eisen: Dit product voldoet aan de volgende eisen.
!1
RFI Emissie
EN55022 Klasse B
!2
Immuniteit
EN50082-1 1997
!3
Electrische Veiligheid
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Waarshuwing Klasse-1 laser produkt.
!6
Waarchuwing Neit in de straal staren.
VEILIGHEID
22
AT-MC104 Series Installation Guide
!7
GEVAAR VOOR BLIKSEMINSLAG
GEVAAR: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.
!8
VENTILATIEGATEN NIET BLOKKEREN
!9
Stroom mag alleen via de adapter naar het apparaat toegevoerd worden.
EUROPE - EU
Gebruik een door TÜV gekeurde wisselstroomadapter van 12 Volt gelijkstroom, 500
milliampères.
! 10
BEDRIJFSTEMPERATUUR
De omgevingstemperatuur voor dit produkt mag niet meer bedragen dan 40 graden
Celsius.
! 11
ALLE LANDEN: het toestel installeren overeenkomstig de lokale en nationale
elektrische voorschriften.
Normes: ce produit est conforme aux normes de suivantes :
!1
Emission d'interférences
radioélectriques
EN55022 Classe B
!2
Immunité
EN50082 - 1 1997
!3
Sécurité électrique
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Attention Producit laser di classe 1.
!6
Attention Ne pas fixer le faisceau des yeux.
SÉCURITÉ
!7
DANGER DE FOUDRE
DANGER: NE PAS MANIER le matériel ou les CÂBLES lors d'activité orageuse.
!8
NE PAS BLOQUER LES FENTES D'AÉRATION
!9
L'alimentation du concentrateur doit être uniquement fournie par l'adaptateur.
EUROPE - EU
Utiliser un adaptateur secteur conforme TÜV de 12 V, 500 mA en courant continu.
! 10
TEMPÉRATURE DE FONCTIONNEMENT
Ce matériel est capable de tolérer une température ambiante maximum de 40 degrés
Celsius.
! 11
POUR TOUS PAYS: Installer le matériel conformément aux normes électriques
nationales et locales.
23
Standardit: Tämä tuote on seuraavien standardien mukainen.
!1
Radioaaltojen häirintä
EN55022 Luokka B
!2
Kestävyys
EN50082-1 1997
!3
Sähköturvallisuus
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Varoitus Luokan 1 Lasertuote.
!6
Variotus Älä katso säteeseen.
TURVALLISUUS
!7
SALAMANISKUVAARA
ENGENVAARA: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.
!8
ÄLÄ TUKI ILMAREIKIÄ
!9
Tähtipisteeseen (hub) syötettävän virran pitää tulla ainoastaan sovittimesta.
EUROPE - EU
Käytä TÜV-lisenssillä valmistettua verkkosovitinta, jonka tasajännitteen
nimellisarvot ovat DC 12 V, 500 mA (milliampeeria).
! 10
KÄYTTÖLÄMPÖTILA
Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle 40° C.
! 11
KAIKKI MAAT: Asenna tuote paikallisten ja kansallisten
sähköturvallisuusmääräysten mukaisesti.
Standard: Questo prodotto è conforme ai seguenti standard.
!1
Emissione RFI (interferenza di
radiofrequenza)
EN55022 Classe B
!2
Immunità
EN50082-1 1997
!3
Sicurezza elettrica
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Avvertenza Prodotto laser di Classe 1.
!6
Avertenza Non fissare il raggio con gli occhi.
NORME DI SICUREZZA
!7
PERICOLO DI FULMINI
PERICOLO: NON LAVORARE sul dispositivo o sui CAVI durante
PRECIPITAZIONI TEMPORALESCHE.
!8
NON OSTRUIRE LE PRESE D'ARIA
24
AT-MC104 Series Installation Guide
!9
Questo dispositivo deve essere alimentato solo mediante l’adattatore.
EUROPE - EU
Utilizzare l’adattatore per c.a. da 12 V c.c. e 500 mA conforme alla normativa TÜV.
! 10
TEMPERATURA DI FUNZIONAMENTO
Questo prodotto è concepito per una temperatura ambientale massima di 40 gradi
centigradi.
! 11
TUTTI I PAESI: installare il prodotto in conformità delle vigenti normative
elettriche nazionali.
Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.
!1
RFI stråling
EN55022 Klasse B
!2
Immunitet
EN50082-1 1997
!3
Elektrisk sikkerhet
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
ADVARSEL Laserprodukt av klasse 1.
!6
ADVARSAL Stirr ikke på strålen.
SIKKERHET
!7
FARE FOR LYNNEDSLAG
FARE: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.
!8
BLOKKER IKKE LUFTVENTILENE
!9
All strømtilførsel må komme fra adapteren.
EUROPE - EU
Benytt TÜV-godkjent AC-adapter på 12V DC, 500mA (millismpere)
! 10
DRIFTSTEMPERATUR
Dette produktet er konstruert for bruk i maksimum romtemperatur på 40 grader
celsius.
! 11
ALLE LAND: Produktet må installeres i samsvar med de lokale og nasjonale
elektriske koder.
25
Padrões: Este produto atende aos seguintes padrões.
!1
Emissão De Interferência De
Radiofrequência
EN55022 Classe B
!2
Imunidade
EN50082-1 1997
!3
Segurança Eléctrica
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
Aviso Produto laser de classe 1.
!6
Aviso Não olhe fixamente para o raio.
SEGURANÇA
!7
PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.
!8
NÃO BLOQUEIE AS ABERTURAS DE VENTILAÇÃO
!9
Use somente o adaptador fornecido para alimentação elétrica do hub.
EUROPE - EU
Use um adaptador de corrente alternada com saída DC de 12V e 500mA em
conformidade com as especificações da TÜV.
! 10
TEMPERATURA DE FUNCIONAMENTO
Este produto foi projetado para uma temperatura ambiente máxima de 40 graus
centígrados.
! 11
TODOS OS PAÍSES: Instale o produto de acordo com as normas nacionais e locais
para instalações elétricas.
Estándares: Este producto cumple con los siguientes estándares.
!1
Emisión RFI
EN55022 Clase B
!2
Inmunidad
EN50082-1 1997
!3
Seguridad eléctrica
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
¡ADVERTENCIA! Producto láser Clase 1.
!6
¡ADVERTENCIA! No mirat fijamente el haz.
SEGURIDAD
!7
PELIGRO DE RAYOS
ELIGRO: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los
equipos o en LOS CABLES durante TORMENTAS ELECTRICAS.
!8
NO BLOQUEE LAS ABERTURAS PARA VENTILACION
26
AT-MC104 Series Installation Guide
!9
La energía para el dispositivo central o "hub" debe provenir únicamente del
adaptador.
EUROPE - EU
Utilizar un adaptador de corriente alterna autorizado TÜV de 12 voltios de corriente
continua y 500 miliamperios.
! 10
TEMPERATURA REQUERIDA PARA LA OPERACIÓN
Este producto está diseñado para una temperatura ambiental máxima de 40 grados
C.
! 11
PARA TODOS LOS PAÍSES: Monte el producto de acuerdo con los Códigos
Eléctricos locales y nacionales.
Standarder: Denna produkt uppfyller följande standarder.
!1
Radiostörning
EN55022 Klass B
!2
Immunitet
EN50082-1 1997
!3
Elsäkerhet
TUV-EN60950, UL1950, CSA 950
!4
Laser
EN60825
!5
VARNING! Laserprodukt av klass 1.
!6
VARNING! Laserstrålning när enheten är öppen.
SÄKERHET
!7
FARA FÖR BLIXTNEDSLAG
FARA: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.
!8
BLOCKERA INTE LUFTVENTILERN
!9
Endast anslutningsenheten får vara kraftkälla till centralen.
EUROPE - EU
Använd en växelströmsanslutningsenhet licensierad av TÜV. Likström 12V, 500mA.
! 10
DRIFTSTEMPERATUR
Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader
Celsius.
! 11
ALLA LÄNDER: Installera produkten i enlighet med lokala och statliga
bestämmelser för elektrisk utrustning.
27
Appendix B
AT-MC104 Series Installation Guide
Feedback
Please tell us what additional information you would like to see discussed in
this guide. If there are topics you would like information on that were not
covered in this guide, please photocopy this page, answer the questions and
fax or mail this form back to Allied Telesyn. The mailing address and fax
number are at the bottom of the page. Your comments are valuable when we
plan future revisions of this guide.
I found the following the most valuable __________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
I would like the following more developed ________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
I would find this guide more useful if ____________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Please fax or mail your feedback. Fax to 1-408-736-0100. Or mail to:
Allied Telesyn International, Corp.
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA
PN 613-10781-00 Rev D
29
Appendix C
Technical Support Fax Order
Name _________________________________________________________________
Company ______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province_______________________________
Zip/Postal Code ________________ Country_______________________________
Phone ______________________________ Fax_______________________________
Incident Summary
Model number of Allied Telesyn product I am using________________________
Firmware release number of Allied Telesyn product________________________
Other network software products I am using (e.g., network managers)
______________________________________________________________________
______________________________________________________________________
Brief summary of problem ______________________________________________
______________________________________________________________________
Conditions (List the steps that led up to the problem.)______________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as batch files and configuration
files. When completed, fax this sheet to the appropriate Allied Telesyn office.
Fax numbers can be found on page viii.
31