WarmlyYours TW-E3CP Operating instructions

Hardwired Model Shown
Installation & Operation Manual for
WarmlyYours Infinity Towel Warmers
Thank you for choosing your finely crafted WarmlyYours Towel Warmer.
Now you can add luxury and comfort to your bathroom with the soothing
embrace of a warm towel or bathrobe upon stepping from the bath or
shower. The radiant heat from the Towel Warmer warms your towel. Included
in this document are all necessary installation and operating instructions.
For model number, reference the location of the product label as shown in
Diagram D on page 7. If you encounter any difficulties while installing your
Towel Warmer, installation support is available by phone between the hours
of 8:00am - 5:30pm CST, Monday through Friday by calling (800) 875-5285.
If a return is necessary, please use original packaging.
Safety Information
• Towel Warmers are designed to warm towels and bathrobes only and should not
be used for any other purpose.
• Never stand, sit on or hang on the Towel Warmer unit.
• Never allow children to play on or with the Towel Warmer.
• Make sure that the electrical circuit breaker is shut off at the main panel before
wiring or servicing your Towel Warmer.
• The Towel Warmer must be properly grounded.
• All wiring must be in accordance with the National Electrical Code (NEC)
and Canadian Electrical Code (CEC) and should be performed by a licensed
professional who is certified to do electrical wiring.
• Never place your Towel Warmer inside a shower, sauna or steam room.
• Never attempt to warm more than two (2) towels on the Towel Warmer at a time.
Overloading the Towel Warmer will cause the unit to become extremely hot and
may result in a burn if touched. (See page 10 for additional information.)
• Infinity Towel Warmers are cULus listed for use in US and Canadian markets.
• Never use an extension cord (for Plug-in model).
Cleaning Information
Clean the Towel Warmer with a soft, non-abrasive, damp cloth while warm.
Once the Towel Warmer has cooled, lightly polish with a soft dry cloth. Do
not use abrasive cleaning powders, metal polish or chlorine based cleaners
on any part of the Towel Warmer.
Installation
This appliance must be installed in accordance with the instructions in the
manual and the NEC and CEC guidelines relating to electrical fixtures in
bathrooms. The Towel Warmer must be on a GFCI protected circuit and be
wired by a professional who is certified to do electrical wiring. If the Towel
Warmer does not heat upon initial installation, PLEASE VERIFY THAT THE
“POWER” SWITCH, LOCATED AT THE BOTTOM OF THE LEFT, VERTICAL
POST, IS IN THE “ON” POSITION.
1
Affixing the Towel Warmer to the Wall
Step 1
Draw a diagram of the preferred location of the brackets and the electrical
connection on the Towel Warmer box to create a template (see Step 2 for
template instructions). At least two of the four brackets must be attached
directly to a stud.
The Infinity Plug-In model must be installed less than 6’ (183cm) from
a properly grounded outlet to ensure the plug can reach. Make sure to
measure the distance from where to plug is attached to the Towel Warmer to
the electrical outlet. Do NOT use an extension cord to make the connection
between the Towel Warmer plug and outlet.
Step 2
A. Attach tubing into desired positions on the Towel Warmer (see pages 5-6
for bracket assembly).
B. Place Towel Warmer on the box (or a large sheet of paper) and lay on a
flat surface with brackets facing downwards.
C. Mark the location of the following:
• The electrical collar (Hardwired model only).
• The location of the brackets.
D. Use the template as a guide to mark the wall with the correct locations
of the four brackets, ensuring the following:
• The electrical collar is lined up with the center of the electrical
box (Hardwired model only). Plug-in model must be installed less
than 6’ (183cm) from properly grounded outlet. Do NOT use an
extension cord.
• At least two of the brackets are lined up with a wall stud.
• The Towel Warmer is level.
Step 3
Install the brackets onto the wall. Use the drywall anchors that are supplied
for the brackets that are not being installed into a stud. Refer to Diagram
A and B.
2
Affixing the Towel Warmer to the Wall - cont’d
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING:
Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
Diagram A: Anchor Points and Electric Box Location
stud
16” (406mm)
stud
223/8” (568mm)
8”
(203mm)
anchor point*
anchor point
anchor point*
anchor point
151/4”
(388mm)
8 1/8” (206mm)
electrical collar
electrical box†
†
Note: H
ardwired model only Electrical box must be securely attached to a stud.
Plug-in model only must be installed less than 6’ (183cm) from properly
grounded outlet. Do NOT use an extension cord.
* Note: Anchor points must be attached to a stud.
3
Diagram B: Rough-In Diagram
Note: Dimensions shown are distances between the center of anchor
points. This example shows 16” on center construction. Your situation
may vary depending on your stud spacing.
WARNING:
Locations of electrical box and anchor points may vary.
Measure all dimensions prior to rough-in and installation.
2” X 4” STUD
(51mm x 102mm)
2” X 4” STUD
(51mm x 102mm)
PERMANENT 120V ac
FROM HOUSE POWER
16” (406mm)
Hardwired Model Only
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX
FOR TIMER
15 1/4”
(388mm)
1/2” (13mm) CONDUIT
8 1/8”
(206mm)
22 3/8”
(568mm)
Hardwired Model Only
2” x 4”
(51mm x 102mm)
ELECTRICAL BOX FOR TOWEL
WARMER CONNECTION†
MOUNT CENTER OFJUNCTION BOX
22 3/8” (568mm) TO THE RIGHT OF CENTER OF STUD
†
Note: H
ardwired model only Electrical box must be securely attached to a stud.
Plug-in model only must be installed less than 6’ (183cm) from properly
grounded outlet. Do NOT use an extension cord.
* Note: Anchor points must be attached to a stud.
4
Diagram C: Bracket Assembly Diagrams - Infinity
A
A
A
A
B
A
A
A
g
g
B
B
B
C
C
B
B
C
C
C
C
A
g g
g
g
C
C
C C
C
C
h
h
d
d
h
hh
B
B
d
ed
e
e
fedd
f
f
g
h
g fee h g ff
g
h
h
B
B
B
B
A
A
A
5
A
A
A B
B
B
B
B
B
h gg
hh
Infinity TW-F10BS-HW Parts List
B
B
B B
B
C
B
A
A
C
C C
C
C
B
B
B
A
C
C
C
A
g
g
g
d
de
d
C
C
h
B
e
egd
f e hgfe f h g f g h gh
f
g
d
C
C
h h
def d
de
h
h
i
ef d
fg e hg
fh
g
h
h
B
h
PART #
B B
Infinity Brushed Nickel TW-F10BS-HW
B
h
h
QTY
A. 0005-57110-0001
DESCRIPTION
4
Bracket, mounting, stainless steel
4
Tube Assy., mounting, stainless steel
4
Screw, Tube mounting, 8mm x 70mm
d. 0005-57900-0001
1
Wrench, hex key, 8mm
e. 0005-57900-0002
1
Wrench, hex key, 6mm
f. 0005-57500-0001
4
Anchor, drywall, #8, white
g. 0005-57200-0001
4
Screw, #8 x 3”, flat
h. 0005-57200-0002
4
Screw, set, 6mm, hex
B. 0005-57110-0002
C. 0005-57300-0001
i. 0005-57810-0000
A
A
B
A A BA
AK05-57820-0001
B
B
B
1
Collar
N/A
A
B B
PartsB Kit Assy, Infinity, TW-F10BS-HW
AB
A
6
B
B
Bracket Assembly Instructions
Step 4
Measure for bracket positions using the template if desired. At least two brackets
must be attached to a stud.
Step 5
Affix brackets A to the wall using screw g and drywall anchor f where necessary.
Repeat Step 5 for the three remaining brackets.
Step 6
Place and orient the curved end of tubing B with the threaded inserts located
at four points on the back of the Towel Warmer. Affix tubing B to the threaded
inserts with bolt C and tighten using the large Allen wrench d provided.
Repeat Step 6 for the three remaining sections of tubing.
Step 7
Loosen the hex-head screws h at the base of each section of tubing B using the
smaller Allen wrench e provided. Hang Towel Warmer by aligning and sliding all
four sections of tubing B over bracket A. Partially tighten hex-head screws h at
the base of each section of tubing B to hold the Towel Warmer in place but do
NOT fully secure the fasteners at this time.
Step 8
Plug-In model Skip Steps 8-11.
Hardwired Model only
Slide the brushed stainless collar over the end of the stainless steel tubing where
the wires come out of the unit. Make sure to slide the collar over the tubing
so that the larger diameter opening is facing away from the Towel Warmer and
toward the electrical cover plate that will be placed on the Towel Warmer next.
Remove the blue plastic coating from the cover plate. Slide the cover plate over
the same section of stainless steel tubing. Refer to Diagram E. Do not remove
rubber o-ring from electrical plate under any circumstances. Make sure the
cover plate is slid on the tubing so that the back of the cover faces away from the
Towel Warmer and toward the electrical outlet.
Step 9
Have a certified professional wire the Towel Warmer to the electrical circuit according
to code, referring to the detailed wiring diagram provided in Diagram F.
Step 10
Push the wires into the electrical box and screw the cover plate to the outside of
the box with the screws provided.
7
Bracket Assembly Instructions - cont’d
Step 11
Hardwired model only continued.
Ensure the rubber seal is in position and sealed correctly inside the collar.
Refer to Diagram E. Slide the brushed stainless collar over the tube until
it is touching the face of the O-Ring on the cover plate.
Plug-In Model
Plug the cord into a properly grounded outlet. Do NOT use an extension
cord to make the connection between the Towel Warmer plug and
outlet.
Step 12
Hold the Towel Warmer in place while tightening the hex-head screws h
at the base of each section of tubing B using the smaller Allen wrench e
provided to secure the Towel Warmer in place.
Step 13
Make sure the unit is turned on using the ON/OFF switch located at the
bottom rail on the left-side (when facing the Towel Warmer). A red light
will illuminate the switch when the switch is turned to the “ON” position.
Refer to Diagram D for switch location.
Diagram E
Diagram D
Hardwired model only
O-ring
Label
Towel Warmer
Collar
Cover Plate
Switch
8
Appendix F: Wiring Diagram (Hardwired models only)
2” x 4” ELECTRICAL
BOX FOR TIMER
120 Volt TIMER
TOWEL WARMER
LINE
(black)
120 a.c. HOT
NEUTRAL
(white)
NEUTRAL
LOAD
(blue)
GROUND
BLACK or BLUE (Hot)
GREEN/YELLOW (Ground)
WHITE or BROWN
(Neutral)
HOT LOAD
(black or blue)
NEUTRAL LOAD
(white or brown)
GROUND
(green/yellow)
2” x 4” ELECTRICAL BOX
9
Operation
Your WarmlyYours Towel Warmer is designed to warm towels, it is not
recommended for any other use.
Plug-In Model
With your Infinity Plug-In model secured to the wall and plugged into a
grounded outlet, you are now ready to enjoy your Towel Warmer. Use the ON/
OFF switch located on the bottom left-side (when facing the Towel Warmer)
to control when you want the unit to warm. Refer to Diagram D for switch for
location.
Hardwired Model
WarmlyYours Towel Warmers include our programmable timer for
luxurious and economical use of the Towel Warmer.
On
Towel Warmer runs at 100% power and will reach temperatures
between 100° F and 140° F depending on the following: running
time, number of towels, type of towels and ambient room
temperature. For optimal use we recommend Automatic Mode.
Automatic Mode
Diagram G.
Programmable Timer allows up to 14 events or Two ON-OFF
cycles per day. Easy programming allows you to set intervals
of operation for each day of the week. To access programming
controls flip the switch panel up. Reference Diagram G for
switch location.
Manual Mode
Timer can be set to operate in manual mode to function as a
simple ON-OFF switch.
Warning
For optimum operation of your new towel warmer, we recommend placing
no more than two (2) towels at a time on the warmer. Place the towels in a
way to maximize the contact area between the towel and the towel warmer.
The towel will be its warmest when it is placed over the top bar. This allows
a greater portion of the towel to make the most contact with the warmer.
We also suggest not operating the warmer for extended periods of time.
Most customers find that setting the timer to operate the warmer 30 minutes
before and 30 minutes after the towel’s use is sufficient. Your results may vary
depending on the materials and construction of your towels.
10
SPECIFICATIONS
Item #
Model
Dimensions
Volts
Watts
Ohms
Amps
TW-F10BS-HW
Hardwired
23 5/8” (600mm)W
32” (811mm)H
4 ¾” (121mm)D
120
150
95
1.25
TW-F10BS-PL
Plug-In
23 5/8” (600mm)W
32” (811mm)H
4 ¾” (121mm)D
120
150
95
1.25
Product Construction - Towel Warmer
The Infinity Towel Warmers are constructed from Type 304 stainless steel
and have a brushed finish. The stainless steel tubing is pre-assembled
and tack welded together for rigidity. The Towel Warmer is heated by
a cULus listed wire. The tubing used to hang the Towel Warmer is also
made of Type 304 stainless steel polished to a brushed finish. The Plug-in
model is equipped with a UL-Listed plug with grounding pin that is 6 feet
(1.8m) long.
Connection Method
Infinity Plug-In models is fed electricity into the Towel Warmer through
a cULus listed cord with grounded plug. The unit must be plugged into
an outlet that is properly grounded. The Infinity Hardwired model is fed
electricity into the Towel Warmer via a section of stainless steel tubing. The
tubing can rotate to facilitate wiring. The tubing has an outside diameter
suitable to secure the rubber O-ring on the electrical cover plate. The
stainless steel tubing projects through the O-ring and into the front of the
2”x4” (51mm x 102mm) electrical junction box that is properly grounded.
This box is secured in the wall and a water resistant seal is made with the
use of the rubber O-ring. Power can then be fed to the control unit which
may be located anywhere in the room.
Safety Ratings
Infinity Towel Warmers are cULus listed and are suitable for use in US
and Canadian markets. The timer is UL listed and CSA certified. The
Timer is humidity sealed to IEC standards for zone 1 (areas where it may
be splashed by water) and zone 2 (areas which are occasionally subject
to high humidity) and therefore suitable for installation in damp locations
such as bathrooms. The main electrical line feeding the Towel Warmer
must incorporate an Appliance Leakage Current Interrupter (ALCI) for
North America.
11
WarmlyYours Towel Warmer Warranty
WarmlyYours.com Inc. warrants the WarmlyYours Towel Warmers (“the Product”)
to be free from defects in materials and workmanship for two years from the date of
sale, provided that the Product is installed in accordance with the accompanying
Installation and Operation Manual, and any special written design or installation
guidelines provided by WarmlyYours.com Inc. for this product, the National Electric
Code (NEC) and Canadian Electrical Code (CEC), and all applicable local building
and electrical codes. Controls sold under the WarmlyYours.com Inc. name are
warranted for one year from the date of sale.
Any suspected defect must be reported by registered letter immediately upon
discovery. The determination of such a defect must be made by WarmlyYours.
com Inc., or its authorized representative only. This warranty is null and void if the
product is improperly installed, improperly operated, or abused. WarmlyYours.
com Inc. assumes no responsibility under this warranty for any damage to the
product caused by any trades person, or visitor on the job site, or damage caused
as a result of post installation work.
Under this Limited Warranty, WarmlyYours.com Inc. will provide the following
remedy:
If the Product is determined to be defective in materials and workmanship, and
has not been damaged as a result of misuse or misapplication, WarmlyYours.
com Inc. will refund the original purchase price or replace the Towel Warmer, at
WarmlyYours.com Inc. expense. WarmlyYours.com Inc. will not be liable for the
labor required to replace the Towel Warmer.
The Limited Warranty is null and void if the project owner or his representative
attempts to repair the Product without receiving authorization. Upon notification
of a real or possible problem, WarmlyYours.com Inc., will issue an Authorization
to Proceed under the terms of the Limited Warranty.
WARMLYYOURS.COM INC. DISCLAIMS ANY WARRANTY NOT PROVIDED
HEREIN, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.
WARMLYYOURS.COM INC. FURTHER DISCLAIMS ANY RESPONSIBILITY
FOR SPECIAL, INDIRECT, SECONDARY, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES ARISING FROM OWNERSHIP OR USE OF THIS PRODUCT,
INCLUDING INCONVENIENCE OR LOSS OF USE. THERE ARE NO WARRANTIES
WHICH EXTEND BEYOND THE FACE OF THIS DOCUMENT. NO AGENT OR
REPRESENTATIVE OF WARMLYYOURS.COM INC. HAS ANY AUTHORITY
TO EXTEND OR MODIFY THIS WARRANTY UNLESS SUCH EXTENSION OR
MODIFICATION IS MADE IN WRITING BY A CORPORATE OFFICER.
Please fill in warranty card info at
www.warmlyyours.com/h/cp-warranty-registration
or call (800) 875-5285 to register via phone.
12
10062 9/2012