BOXLIGHT CP-322i/CP-634i User`s manual

00CP317/327WBasic 03.5.27 3:04 PM ページ 2
BOXLIGHT
Liquid Crystal Projector
CP-322i/CP-634i
ENGLISH
USER'S MANUAL Vol.1 Basic
DEUTSCH
Please read this user's manual thoroughly to ensure correct usage through understanding.
FRANÇAIS
ITALIANO
ESPAÑOL
NEDERLANDS
NORSK
PORTGÊS
中文
STANDBY/ON
REGULATORY
NOTICES
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
CP-S317/327W/最終 03.5.27 2:22 PM ページ 1
LCD Projector CP-322i
USER'S MANUAL
Vol.1 (Basic)
Thank you for purchasing this projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
Page
Page
PROJECTOR FEATURES ................2
PREPARATIONS ..............................2
PART NAMES ...................................4
SETTING UP
THE PROJECTOR ............................6
CONNECTING
YOUR DEVICES................................8
USING THE REMOTE
CONTROL .......................................13
TURNING ON THE POWER ...........14
TURNING OFF THE POWER .........16
ADJUSTING THE VOLUME ...........17
TEMPORARILY MUTING
THE SOUND....................................17
ADJUSTING THE POSITION..........18
USING THE AUTOMATIC
ADJUSTMENT FEATURE ..............19
CORRECTING KEYSTONE
DISTORTIONS ................................20
USING THE MAGNIFY
FEATURE........................................21
FREEZING THE SCREEN ..............21
SIGNAL SEARCHING.....................22
SELECTING THE ASPECT
RATIO..............................................22
TEMPORARILY BLANKING
THE SCREEN..................................22
USING THE MENU
FUNCTIONS....................................23
OPERATING THE PC SCREEN .....24
THE LAMP ......................................25
THE AIR FILTER.............................27
OTHER CARE .................................29
REGULATORY NOTICES...............30
1
CP-S317/327W/最終 03.5.27 2:22 PM ページ 2
PROJECTOR
FEATURES
This liquid crystal projector is used to project
various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space
is required for installation and large images can
easily be realized.
●Ultra High Brightness
●Keystone Distortion Correction
●Partial Magnification Function
●Whisper Mode Equipped
Crisp, ultra-bright presentations is achieved
by using a UHB (ultra high brightness) lamp
and a highly efficient optical system
Interesting parts of images can be magnified
for closer viewing
PREPARATIONS
Quick correction of distorted images electrically
Special mode is available for reducing
projector noise to achieve quieter operation
Your projector should come with the items
shown below. Check to make sure that all the
items are included. Contact your dealer if
anything is missing.
NOTE • Keep the original packing material for future reshipment.
STANDBY/ON
Power cord
(US Type)
Power cord
(UK Type)
Power cord
(Europe Type)
RGB cable
Video/Audio cable
USB mouse
cable
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
Projector
(with Lens Cap)
Liquid Crystal Projector
ENGLISH
CP-S317/CP-X327
(CP-S317W/CP-X327W)
USER'S MANUAL Vol.1 Basic
Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de
uitgebreide mogelijkheden.
BRUKERHÅNDBOK Vol.1 Grunnleggende
Vennligst les denne bruksanvisningen grundig for å være garantert driftssikker bruk.
NSTRUÇÕES DO PROPRIETÁRIO Vol.1 Básico
Para assegurar o uso correto do equipamento, por favor leia atentamente este manual do utilizador.
NEDERLANDS ESPAÑOL
MANUAL DE USUARIO Vol.1 Básico
Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.
GEBRUIKSAANWIJZING Vol.1 Basis
STANDBY/ON
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
PORTGÊS
NORSK
MANUEL D'UTILISATION Vol.1 Fondements
Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.
MANUALE D'ISTRUZIONI Vol.1 Informazioni di base
Vi preghiamo voler leggere attentamente il manuale d'istruzioni in modo tale da poter comprendere quanto riportato
ai fini di un corretto utilizzo del proiettore.
ITALIANO FRANÇAIS DEUTSCH
Please read this user's manual thoroughly to ensure correct usage through understanding.
BEDIENUNGSANLEITUNG Teil 1 Grundlagen
Bitte lessen Sie diese Benutzerhandbuch zugunsten der korrekten Bedienung aufmerksam.
User's Manual
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ON
MUTE
OFF
FREEZE
Two AA batteries
(for the remote
control)
Soft carrying case
2
KEYSTONE
POSITION
MENU
ENTER
ESC
RESET
Remote control
CP-S317/327W/最終 03.5.27 2:22 PM ページ 3
WARNING Precautions to observe in regards to the power cord: Please use extra
caution when connecting the projector's power cord as incorrect or faulty
connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the
following safety guidelines to insure safe operation of the projector:
• Only plug the power cord into outlets rated for use with the power cord's specified voltage range.
• Only use the power cord that came with the projector.
• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREEPRONGED PLUG!
• Make sure that you firmly connect the power cord to the projector and wall outlet.
1
Connect your devices to the projector
2
Insert the batteries into the remote
control
3
Connect the power cord
Connect your computer, VCR and/or other
devices you will be using to the projector.
8
∼ 12
13
(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.
(2) Firmly plug the power cord's plug into the outlet
Power outlet
(1)
AC inlet
(2)
Power cord
3
CP-S317/327W/最終 03.5.27 2:22 PM ページ 4
THE PROJECTOR
PART NAMES
Indicates the corresponding
reference page
24 RESET button
MENU button 23
POWER indicator 14
20 KEYSTONE button
TEMP indicator 27
15 INPUT button
LAMP indicator 26
14 STANDBY/ON button
15 Zoom ring
STANDBY/ON
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
15 Focus ring
27 Air filter
6
Elevator button
Remote sensor 13
Lens cap 14
11 S-VIDEO IN port
10 AUDIO IN R and L ports
10 RGB IN 1 and 2 ports
11 VIDEO IN port
STANDBY/ON
INPUT
3 AC power inlet
KEYSTONE
RESET
LANP
POWERTENP
6
10 CONTROL port
12 RGB OUT port
10 USB port
11 COMPONENT VIDEO port
4
Elevator button
14 Power switch
CP-S317/327W/最終 03.5.27 2:22 PM ページ 5
THE REMOTE CONTROL
22 SEARCH button
14 STANDBY/ON button
RGB button 15
STANDBY/ON
VIDEO button 15
VIDEO
RGB
SEARCH
19 AUTO button
ASPECT
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
22 BLANK button
ASPECT button 22
MAGNIFY
17 VOLUME button
ON
MAGNIFY buttons 21
17 MUTE button
OFF
FREEZE
KEYSTONE
FREEZE button 21
20 KEYSTONE button
KEYBOARD buttons 24
POSITION
MENU
POSITION button 18
23 MENU button
ENTER
,
,
,
23
Cursor buttons
ESC button 23
ESC
RESET
24 RESET button
23 ENTER button
5
CP-S317/327W/最終 03.5.27 2:22 PM ページ 6
SETTING UP THE PROJECTOR
CAUTION • Install the projector in a suitable environment according to instructions
of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.
• If you press the elevator buttons without holding the projector, the projector might
crash down, overturn, smash your fingers and possibly result in malfunction. To
prevent damaging the projector and injuring yourself, ALWAYS HOLD THE
PROJECTOR whenever using the elevator buttons to adjust the elevator feet.
Adjusting the Projector's Elevator Feet
You can use the elevator feet to make adjustments if the surface on which you
need to set the projector is uneven or if you otherwise need to adjust the angle of
projection. The adjustment range of the elevator feet is 0 to 9 degrees.
1
2
Press and hold in the elevator
buttons
Raise or lower the projector to the
desired height and then release the
elevator buttons
When you release the elevator buttons, the elevator
feet will lock into position.
3
6
As necessary, you can also finely
adjust the height of the projector by
twisting the elevator feet by hand
CP-S317/327W/最終 03.5.27 2:22 PM ページ 7
Adjusting the Screen Size and Projection Distance
Refer to the illustrations and tables below to determine the screen size and
projection distance.
The values shown in the table are calculated for a full size screen
(CP-S318: 800x600 pixels/CP-X328: 1024x768 pixels).
a:Distance from the projector to the screen (±10%)
b:Distance from the lens center to the bottom of the screen (±10%)
c:Distance from the lens center to the top of the screen (±10%)
The screen
Top view
If 4:3 aspect ratio
4
3
Screen Size [inch (m)]
c
30 (0.8)
40 (1.0)
50 (1.3)
60 (1.5)
70 (1.8)
80 (2.0)
90 (2.3)
100 (2.5)
120 (3.0)
150 (3.8)
200 (5.0)
250 (6.3)
300 (7.5)
Lens center
Side view
b
a
The screen
Top view
a [inch (m)]
b
Min.
Max. [inch (cm)]
35 (0.9) 42 (1.1) 1 (2)
47 (1.2) 56 (1.4) 1 (3)
59 (1.5) 71 (1.8) 1 (4)
71 (1.8) 85 (2.2) 2 (4)
83 (2.1) 100 (2.5) 2 (5)
95 (2.4) 114 (2.9) 2 (6)
107 (2.7) 129 (3.3) 3 (7)
119 (3.0) 143 (3.6) 3 (7)
143 (3.6) 172 (4.4) 3 (9)
180 (4.6) 216 (5.5) 4 (11)
240 (6.1) 288 (7.3) 6 (15)
300 (7.6) 361 (9.2) 7 (18)
360 (9.2) 433 (11.0) 9 (22)
c
[inch (cm)]
17 (44)
23 (58)
29 (73)
34 (87)
40 (102)
46 (116)
51 (131)
57 (145)
69 (174)
86 (218)
114 (290)
143 (363)
171 (435)
a [inch (m)]
Min.
Max.
38 (1.0) 46 (1.2)
51 (1.3) 61 (1.6)
64 (1.6) 77 (2.0)
77 (2.0) 93 (2.4)
90 (2.3) 109 (2.8)
104 (2.6) 125 (3.2)
117 (3.0) 140 (3.6)
130 (3.3) 156 (4.0)
156 (4.0) 188 (4.8)
196 (5.0) 235 (6.0)
261 (6.6) 314 (8.0)
327 (8.3) 393 (10.0)
393 (10.0) 472 (12.0)
c
[inch (cm)]
16 (41)
22 (55)
27 (69)
32 (82)
38 (96)
43 (110)
49 (124)
54 (137)
65 (165)
81 (206)
108 (275)
135 (343)
162 (412)
If 16:9 aspect ratio
16
9
Screen Size [inch (m)]
c
Lens center
Side view
b
a
30 (0.8)
40 (1.0)
50 (1.3)
60 (1.5)
70 (1.8)
80 (2.0)
90 (2.3)
100 (2.5)
120 (3.0)
150 (3.8)
200 (5.0)
250 (6.3)
300 (7.5)
b
[inch (cm)]
2 (4)
2 (5)
3 (6)
3 (8)
4 (9)
4 (10)
5 (12)
5 (13)
6 (15)
8 (19)
10 (26)
13 (32)
15 (39)
7
CP-S317/327W/最終 03.5.27 2:22 PM ページ 8
CONNECTING YOUR DEVICES
Devices You Can Connect to the Projector
(Refer to this section for planning your device
configuration to use for your presentation.)
CAUTION • Incorrect connecting could result in fire or electrical shock. Please
read this manual and the separate “SAFETY INSTRUCTIONS”.
ATTENTION Precautions to observe when connecting other devices to the projector
• Whenever attempting to connect other devices to the projector, please thoroughly
read the manual of each device to be connected.
• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to
connect a live device to the projector may generate extremely loud noises or other
abnormalities that may result in malfunction and/or damage to the device and/or
projector. Refer to the “TECHNICAL” of the USER’S MANUAL (Vol.2) for the pin
assignment of connectors and RS-232C communication data.
• Make sure that you connect devices to the correct port. Incorrect connection may
result in malfunction and/or damage to the device and/or projector.
• A component cable and some other cables have to be used with core set. Use the
accessory cable or a designated-type cable for the connection. For cables that have
a core only at one end, connect the core to the projector.
• Secure the screws on the connectors and tighten.
Indicates the
corresponding
reference page
12 Display monitors
11 DVD players
10 Laptop computers
11 VCRs
10 Desktop computers
8
CP-S317/327W/最終 03.5.27 2:22 PM ページ 9
Ports and Cables
Refer to the table below to find out which projector port and cable to use for connecting a
given device. Use this table for determining which cables to prepare.
Function
Projector Port
RGB IN 1
RGB input
RGB IN 2
RGB output
RGB OUT
USB mouse control
USB
Connection Cables
Accessory RGB cable or optional RGB
cable with D-sub 15-pin shrink jack and
inch thread screws
Accessory USB cable
PS/2 mouse control
Optional PS/2 mouse cable
ADB mouse control
Optional ADB mouse cable
CONTROL
Serial mouse control
Optional serial mouse cable
RS-232C communication
Optional RS-232C cable
S-video input
S-VIDEO IN
Optional S-video cable with mini DIN 4-pin
jack
Video input
VIDEO IN
Accessory audio/video cable
COMPONENT VIDEO Y
Component video input
COMPONENT VIDEO CB/PB
Optional component video cable
COMPONENT VIDEO CR/PR
AUDIO IN L
Audio input
AUDIO IN R
Accessory audio/video cable or optional
audio cable with RCA jack
NOTE About Plug-and-Play Capability
• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by
connecting this projector to computers that are VESA DDC (display data channel)
compatible. Please take advantage of this function by connecting the accessory RGB
cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.
• Plug-and-Play is a system composed of the computer, its operating system and
peripheral equipment (i.e. display devices).
• Please use the standard drivers as this projector is a Plug-and-Play monitor.
• Plug-and-Play may not function properly with some type of computers. Use the RGB
IN 2 port if Plug-and-Play does not function correctly.
9
CP-S317/327W/最終 03.5.27 2:22 PM ページ 10
CONNECTING YOUR DEVICES (continued)
Connecting to a Computer
ATTENTION Whenever attempting to connect a laptop computer to the projector,
be sure to activate the laptop's RGB external image output (set the laptop to CRT
display or to simultaneous LCD and CRT display). For details on how this is done,
please refer to the instruction manual of the corresponding laptop computer.
1
RGB IN
1
2
R
AUDIO IN
L / (MONO) VIDEO IN
A
S-VIDEO IN
R
CB / PB
CR / RR
Y
COMPONENT VIIDEO
AUDIO IN
L / (MONO) VIDEO IN
USB
RGB OUT
B
Y
D
A
CONTROL
B
10
CONTROL OUT
Analogue
RGB OUT
NOTE
• Some computers may have multiple display screen modes. Use of some of these
modes will not be possible with this projector.
• For some RGB input modes, the optional Mac adapter is necessary.
MOUSE cable
RGB cable
AUDIO OUT
USB OUT
Analogue
RGB OUT
Desktop computer
CONTROL IN
RGB IN
C
AUDIO cable
RGB cable
AUDIO OUT
AUDIO cable
If connecting to a
USB port equipped
computer
D
RGB OUT
USB
AUDIO IN
USB cable
USB IN
RGB IN
AUDIO IN
Laptop computer
CB / PB
COMPONENT VIIDEO
CONTROL
A
B
2
A
S-VIDEO IN
C C
B B
CR / RR
RGB IN
K
K
CP-S317/327W/最終 03.5.27 2:22 PM ページ 11
Connecting to a DVD Player
1
RGB IN
2
K
R
AUDIO IN
L / (MONO) VIDEO IN
S-VIDEO IN
C
B B B
CR / RR
CB / PB
Y
A A A
COMPONENT VIIDEO
RGB OUT
USB
CONTROL
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
COMPONENT VIDEO OUT
COMPONENT cable
S-VIDEO IN
C
AUDIO/VIDEO IN
B
COMPONENT VIDEO IN
A
If using an audio/video
connection
If using a component
video connection
DVD player
Connecting to a VCR
1
RGB IN
2
K
R
AUDIO IN
L / (MONO) VIDEO IN
S-VIDEO IN
B
A A A
CR / RR
CB / PB
Y
COMPONENT VIIDEO
RGB OUT
USB
CONTROL
S-VIDEO IN
B
S-VIDEO cable
If using a S-video
connection
S-VIDEO OUT
AUDIO/VIDEO OUT
AUDIO/VIDEO cable
AUDIO/VIDEO IN
A
VCR
11
CP-S317/327W/最終 03.5.27 2:22 PM ページ 12
CONNECTING YOUR DEVICES (continued)
Connecting to a Display Monitor
1
RGB IN
2
K
AUDIO IN
R
L / (MONO) VIDEO IN
CR / RR
CB / PB
COMPONENT VIIDEO
S-VIDEO IN
A
Y
RGB OUT
USB
CONTROL
A
RGB OUT
RGB IN
RGB cable
Display monitor
12
CP-S317/327W/最終 03.5.27 2:22 PM ページ 13
USING THE REMOTE CONTROL
Putting batteries into the remote control unit
CAUTION Precautions to observe in regards to the batteries
Always handle the batteries with care and use them only as directed. Improper use may result in
battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.
• Keep the battery away from children and pets.
• Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.
• When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).
• When you dispose the battery, you should obey the law in the relative area or country.
1
Remove the battery
cover
Slide back and remove
the battery cover in the
direction of the arrow.
2
Insert the batteries
Align and insert the two AA
batteries (that came with the
projector) according to their plus
and minus terminals (as indicated
in the remote control).
3
Close the battery
cover
Replace the battery cover
in the direction of the arrow
and snap it back into place.
approximately
3 meters
es
gre
de
30 degrees
30
gre
es
de
30
• The remote control works with both the
projector's front and rear remote sensors.
• The range of the remote sensor on the front and
back is 3 meters with a 60-degree range (30
degrees to the left and right of the remote sensor).
• Since the remote control uses infrared light to send
signals to the projector (Class 1 LED), be sure to
use the remote control in an area free from
obstacles that could block the remote control's
output signal to the projector.
30 degrees
Operating the remote control
approximately
3 meters
ATTENTION Precautions to observe when using the remote control
• Do not drop or otherwise expose the remote control to physical impact.
• Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.
• Remove the batteries from the remote control and store them in a safe place if you
won't be using the remote control for an extended period.
• Replace the batteries whenever the remote control starts to malfunction.
• When strong light, such as direct sunlight or light from an extremely close range (such as from an
inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function.
Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.
13
CP-S317/327W/最終 03.5.27 2:22 PM ページ 14
TURNING ON THE POWER
Precautions
Connect all devices to be used to the projector prior to turning on the power.
8
∼ 12
WARNING When the power is ON, a strong light is emitted. Do not look into the
lens.
1
STANDBY/ON
VIDEO
RGB
SEARCH
ASPECT
MAGNIFY
Make sure that the power cord is firmly and
correctly connected to the projector and outlet
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
3
ON
2
OFF
FREEZE
KEYSTONE
Turn on the projector's power
Set the power switch to [ | ] (ON). The projector will go
to STANDBY mode and the POWER indicator will light to
solid orange.
power switch
Control panel
LANP
TENP
POWER
STANDBY/ON INPUT KEYSTONE
POWER indicator
RESET
STANDBY/ON
KEYSTONE
STANDBY/ON
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
NOTE Turn the
power on/off in
right order.
• Power on the
projector before the
computer or video
tape recorder.
• Power off the
projector after the
computer or video
tape recorder.
14
3
RESET
LANP
POWERTENP
INPUT
KEYSTONE
RESET
LANP
POWERTENP
Press the STANDBY/ON button (control
panel or remote control)
• The projector begins warming up and the POWER
indicator blinks green.
STANDBY/ON
• The POWER indicator stops blinking
and lights to solid green once the
projector's power is completely on.
4
Remove the lens cap
The picture is projected.
CP-S317/327W/最終 03.5.27 2:22 PM ページ 15
Selecting an Input Signal
5
Using the remote control
If selecting RGB input
Press the RGB button
Using the projector's control panel
Press the INPUT button
Press this button to toggle between the
devices connected to RGB IN 1 and 2.
As illustrated below, each time you
press the RGB button, the projector
switches between RGB IN 1 and 2.
Select the signal you wish to project.
As illustrated below, each time you
press the INPUT button, the projector
switches between its input signal
ports. Select the signal you wish to
project.
INPUT
RGB
RGB IN 1
RGB IN 2
RGB IN 1
If selecting video input
Press the VIDEO button
Press this button to toggle between the
devices connected to VIDEO IN, SVIDEO IN and COMPONENT VIDEO. As
illustrated below, each time you press
the VIDEO button, the projector
switches between VIDEO IN, S-VIDEO
IN and COMPONENT VIDEO. Select the
signal you wish to project.
VIDEO
VIDEO IN
RGB IN 2
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
S-VIDEO IN
COMPONENT VIDEO
6
Use the zoom ring to adjust the
screen size
7
Use the focus ring to focus the
picture
15
CP-S317/327W/最終 03.5.27 2:22 PM ページ 16
TURNING OFF THE POWER
1
The message "Power off?" will appear on the screen for approximately 5 seconds.
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
Press the STANDBY/ON button (control
panel or remote control)
STANDBY/ON
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
OFF
FREEZE
2
KEYSTONE
POSITION
Press the STANDBY/ON button again while the "Power off?"
message is visible. The projector lamp goes off and starts cooling
down. The POWER indicator blinks orange while the lamp cools
down. (Pressing the STANDBY/ON button while the POWER
indicator is blinking orange has no effect.)
The system goes into the STANDBY mode after cooling
down and the POWER indicator stops blinking orange and
then lights to solid orange.
MENU
ENTER
ESC
Press the STANDBY/ON button again
(control panel or remote control)
RESET
STANDBY/ON
Control panel
LANP
TENP
POWER
STANDBY/ON INPUT KEYSTONE
3
RESET
Check that the POWER indicator stops
blinking and lights to solid
power switch
orange.
Switch the power switch to
[O] (OFF).
POWER indicator
STANDBY/ON
KEYSTONE
LANP
POWERTENP
INPUT
KEYSTONE
RESET
LANP
POWERTENP
STANDBY/ON
INPUT
KEYSTONE
RESET
LANP
TENP
POWER
4
NOTE
• Except in
emergencies, follow
the abovementioned
procedure for
turning power off.
16
RESET
Confirm that the POWER indicator has
gone off and then attach the lens cap.
When the projector has completed powering down, the
POWER indicator will go off.
CP-S317/327W/最終 03.5.27 2:22 PM ページ 17
ADJUSTING THE VOLUME
1
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
Press the VOLUME button
VOLUME
As illustrated on the right, a dialog will
appear on the screen to aid you in adjusting
the volume.
VOLUME
MAGNIFY
ON
16
OFF
FREEZE
KEYSTONE
2
POSITION
MENU
,
buttons to adjust
Press the VOLUME button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
ENTER
ESC
Press the
the volume
RESET
VOLUME
Press this to increase the volume
Press this to decrease the volume
16
TEMPORARILY MUTING THE SOUND
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ON
MUTE
OFF
FREEZE
1
Press the MUTE button
As illustrated on the right, a dialog will appear on the
screen indicating that you have muted the sound. Press
the VOLUME button to close the dialog. (Even if you don't
do anything, the dialog will automatically disappear after
a few seconds.)
Press the MUTE button again to restore the sound.
KEYSTONE
VOLUME
POSITION
MENU
MUTE
ENTER
ESC
RESET
16
17
CP-S317/327W/最終 03.5.27 2:22 PM ページ 18
ADJUSTING THE POSITION
1
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
Press the POSITION button
As illustrated on the right, a dialog will appear on the screen
to aid you in adjusting the position.
ON
POSITION
OFF
FREEZE
KEYSTONE
POSITION
POSITION
MENU
ENTER
ESC
RESET
2
Use the
,
the position
,
,
buttons to adjust
When you want to initialize the position, press the RESET
button during adjustment.
Press the POSITION button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
This function is only available for RGB IN 1/2 input.
18
CP-S317/327W/最終 03.5.27 2:22 PM ページ 19
USING THE AUTOMATIC ADJUSTMENT FEATURE
1
Press the AUTO button
AUTO
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
Automatic Adjustment for RGB Input
ON
OFF
FREEZE
KEYSTONE
POSITION
MENU
ENTER
ESC
Horizontal position (H. POSIT), vertical position (V.
POSIT), clock phase (H. PHASE) and horizontal size (H.
SIZE) are automatically adjusted.
Make sure that the application window is set to its
maximum size prior to attempting to use this feature.
Dark pictures may still be incorrectly adjusted. Use a
bright screen when adjusting.
RESET
Automatic Adjustment for Video Input
The signal type best suited for the respective input
signal is selected automatically.
This feature is available only if VIDEO is set to AUTO in
the INPUT menu.
NOTE
The automatic adjustment operation requires approximately 10 seconds. Also, please
note that it may not function correctly with some input signals.
19
CP-S317/327W/最終 03.5.27 2:22 PM ページ 20
CORRECTING KEYSTONE DISTORTIONS
1
STANDBY/ON
VIDEO
RGB
ASPECT
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
Press the KEYSTONE button
As illustrated on the right, a dialog will appear
on the screen to aid you in correcting the
distortion.
KEYSTONE
KEYSTONE
MAGNIFY
ON
MUTE
16
OFF
FREEZE
KEYSTONE
POSITION
MENU
2
Use the
,
buttons to select the
direction of distortion to correct ( /
3
Use the
distortion
ENTER
ESC
)
RESET
,
buttons to correct the
Press the KEYSTONE button again to close the dialog and
complete this operation. (Even if you don't do anything, the
dialog will automatically disappear after a few seconds.)
NOTE
• This function may not be work well with some types of input signals.
• The adjustable range for correcting keystone distortions will vary with the type of
input signal.
20
CP-S317/327W/最終 03.5.27 2:22 PM ページ 21
USING THE MAGNIFY FEATURE
1
Press the MAGNIFY (ON) button
The projector enters MAGNIFY mode.
MAGNIFY
ON
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
the POSITION button, then use the
, ,
2 ,Pressbuttons
to select the area to enlarge and then
OFF
FREEZE
press the POSITION button again to confirm your
selection
KEYSTONE
POSITION
POSITION
POSITION
MENU
ENTER
ESC
RESET
3
Press the
,
buttons to zoom in and
out of the selected area.
Press the MAGNIFY (OFF) button to exit MAGNIFY mode
and restore the screen to normal. (The projector will also
automatically exit MAGNIFY mode if there is a change in the
input signal's state.)
NOTE
The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,
AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.
FREEZING THE SCREEN
MAGNIFY
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
FREEZE
POSITION
KEYSTONE
Press the FREEZE button
The [II] icon appears and the screen will freeze at
the current image. Press the FREEZE button again
and the [ ] appears as the projector exits FREEZE
mode.
FREEZE
▲
OFF
1
MENU
NOTE
• The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,
BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.
• If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),
the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.
21
CP-S317/327W/最終 03.5.27 2:22 PM ページ 22
SIGNAL SEARCHING
1
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
Press the SEARCH button
When you press the SEARCH button, the projector begins
searching for input signals. If it detects an input signal, the
search will cease and the projector will project the detected
signal. If the projector is unable to find an input signal at any of
its ports, it will return to the state it was in prior to the search.
SEARCH
OFF
FREEZE
KEYSTONE
RGB IN 1
RGB IN 2
COMPONENT VIDEO
VIDEO IN
S-VIDEO IN
SELECTING THE ASPECT RATIO
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
1
SEARCH
Press the ASPECT button
ASPECT
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ON
MUTE
RGB IN 1, RGB IN 2, COMPONENT VIDEO
(HDTV signals : 1125i (1035i/1080i), 750p)
4:3
16:9
VIDEO IN, S-VIDEO IN, COMPONENT VIDEO
(Non-HDTV signals : 525i, 525p,625i)
OFF
FREEZE
KEYSTONE
POSITION
MENU
4:3
ENTER
ESC
16:9
SMALL
RESET
TEMPORARILY BLANKING THE SCREEN
1
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ON
Press the BLANK button
The input signal screen is shut off, and a blank screen
appears. You can set the blank screen using the menu
(from the SCREEN menu, select BLANK). Press the BLANK
button again to remove the blank screen, and return to the
input signal screen.
MUTE
OFF
FREEZE
POSITION
22
KEYSTONE
MENU
BLANK
CP-S317/327W/最終 03.5.27 2:22 PM ページ 23
USING THE MENU FUNCTIONS
1
Press the MENU button
2
/
Select a menu using the
buttons,
then press the
or ENTER button.
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
ON
MUTE
MENU
The menu display appears on the screen. The
projector has the following menus: MAIN,
PICTURE-1, PICTURE-2, INPUT, SCREEN, and
OPTION. Select a menu using the
/
buttons. The
current settings of the items that can be manipulated via the
selected menu appear.
OFF
FREEZE
KEYSTONE
POSITION
MENU
The display of the selected menu appears.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select PICTURE-1, then press
the
or ENTER button.
MENU
ENTER
ESC
RESET
ENTER
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
–1
+1
–1
+1
–1
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
: SELECT
3
Select an item using the
or ENTER button.
/
buttons, then press the
The operation display of the selected item appears. To adjust a numerical value,
press the
or ENTER button again to switch to the single menu (small display
showing only the operation display area).
[ex. Adjusting SHARPNESS]
Use the
/
buttons to select SHARPNESS, then
MENU
press the
or ENTER button.
MAIN
COLOR BAL R
ENTER
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
COLOR BAL B
SHARPNESS
COLOR
TINT
0
: SELECT
4
Press the
/
buttons to adjust the level.
Press the MENU button to hide the menu and finish your operation. Alternatively,
press the
or ESC button to return to the previous display.
[ex. Adjusting SHARPNESS]
Use the
/
buttons to adjust the SHARPNESS.
23
CP-S317/327W/最終 03.5.27 2:22 PM ページ 24
OPERATING THE PC SCREEN
You can use the remote control as a simplified mouse or keyboard.
CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment.
• Only connect to a PC.
• Before connecting, read the manuals of the device you will connect.
• Do not unplug the connector cables while the computer is operating.
PS/2, ADB, Serial Mouse Control
STANDBY/ON
VIDEO
RGB
ASPECT
MAGNIFY
SEARCH
AUTO
BLANK
HOME
PAGE UP
VOLUME
END
PAGE DOWN
MUTE
ON
OFF
FREEZE
KEYSTONE
1. Turn off the projector and PC power, and connect the projector’s
CONTROL terminal to the computer via the mouse cable.
2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control
function is given priority, and mouse control from the CONTROL terminal will not function.
3. Turn on the projector power, then the computer.
The functions in the table below can be controlled. If you have difficulty with control,
restart the computer (either from the software or by pressing the restart button).
Available Functions
POSITION
MENU
Remote Control Operation
Move Pointer
Use
Left click with mouse
Press ENTER button
Right click with mouse
Press RESET button
buttons
ENTER
ESC
RESET
USB Mouse/Keyboard Control
1. Connect the projector’s USB terminal to the computer using a USB cable.
The functions in the table below can be controlled.
Available Functions
Remote Control Operation
Move Pointer
Use
Left click with mouse
Press ENTER button
Right click with mouse
Press RESET button
Press keyboard’s HOME key
Press HOME button
Press keyboard’s END key
Press END button
Press keyboard’s PAGE UP key
Press PAGE UP button
Press keyboard’s PAGE DOWN key
Press PAGE DOWN button
Press keyboard’s ESC key
Press ESC button
buttons
NOTES
• It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.
track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and
select external mouse, and disable the pointing devices. In addition, the mouse may not function if the
computer does not have the needed utility program. See your computer’s hardware manual for details.
• The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to
use the remote control, depending on the computer’s configurations and mouse drivers.
• The USB control can only be used for the functions listed above. You cannot do things like press two buttons
at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).
• This function is not available while the lamp is warming up (the POWER indicator flashes green), while adjusting the volume and
display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.
24
CP-S317/327W/最終 03.5.27 2:22 PM ページ 25
THE LAMP
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately)
then contact your local dealer. Before replacing the lamp, turn off the power, and unplug the power
cord, then wait at least 45 minutes, in order to ensure that the lamp is properly cooled.
Removing the lamp bulb while it is still hot could cause burns, or cause the lamp bulb to burst.
The LCD projector uses a glass lamp bulb. It is a mercury lamp with high
internal pressure. High-pressure mercury lamps can break with a loud
bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a
different lifetime, and some may burst or burn out soon after you start using them. In
addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing,
and for gas containing mercury to escape from the projector’s vent holes.
• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• If the replace lamp indicator (see "Related Messages" (Vol.2 7 ) and "Regarding the
indicator Lamps" (Vol.2 8 )) comes on, replace the lamp as soon as possible. Using the
lamp for long periods of time, or past the replacement date, could cause it to burst. Do
not use old (used) lamps; this is a cause of breakage.
• If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems
elsewhere besides the lamp. If this happens, contact your local dealer.
• If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make
sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.
• If the lamp should break (it will make a loud bang when it does), unplug the power cord from
the outlet, and make sure to request a replacement lamp from your local dealer. Note that
shards of glass could damage the projector’s internals, or cause injury during handling, so
please do not try to clean the projector or replace the lamp yourself.
• Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used
bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.
• Do not use the projector with the lamp cover removed.
WARNING
25
CP-S317/327W/最終 03.5.27 2:22 PM ページ 26
THE LAMP (continued)
Replacing the lamp
All projector lamps will wear out eventually. If used for long periods of time, the image could become
darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps
early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up
the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2 7 ) and "Regarding the
Indicator Lamps" (Vol.2 8 ) for details.)
1
Turn off the projector, and unplug the
power cord. Allow the lamp bulb to cool
for at least 45 minutes, and prepare a
new lamp.
2
After making sure that the projector has
cooled adequately, slowly flip over the
projector, so that the bottom is facing up
3
Unscrew the 2
screws, and
remove the
lamp cover
4
Unscrew the 1 screw, and slowly pull
out the lamp by the handle
• Be careful not to touch the inside of the lamp case.
5
Insert the new lamp, and tighten the 1
screw firmly to lock it in place
• Also steadily push the opposite side of the
screwed side of the
lamp into the unit.
6
Replace the lamp cover, and tighten
the 2 screws firmly to lock it in
place
7
Slowly turn the projector so that
the top is facing up
8
Turn on the projector power, and using
the menu, reset the lamp timer
• To reset the lamp timer, from the OPTION
menu, select LAMP TIME.
ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.
• Do not use with lamp cover removed.
• Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing
the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.
• When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER
WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following
operation within 10 minutes of switching power ON.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature.
Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power
ON again. If the LAMP indicator is still red, replace the lamp.
26
CP-S317/327W/最終 03.5.27 2:22 PM ページ 27
THE AIR FILTER
Caring for the air filter
The air filter should be cleaned about every 100 hours. If the LAMP indicator and
TEMP indicator blink red simultaneously, or a message prompts you to clean the air
filter when you turn on the unit, the filter needs to be cleaned. (See "Related
Messages" (Vol.2 7 ) and "Regarding the Indicator Lamps" (Vol.2 8 ) for details.)
1
Turn off the projector, and unplug the power cord
2
Apply a vacuum cleaner to
the top of the air filter cover
to clean the air filter
Air Filter Cover
3
Turn on the projector, and use the menu to reset the filter
timer
• To reset the air filter timer, from the OPTION menu, select FILTER TIME.
27
CP-S317/327W/最終 03.5.27 2:22 PM ページ 28
THE AIR FILTER (continued)
Replacing the air filter
If the soiling will not come off the air filter, or it becomes damaged, then it needs to be
replaced. Please contact your local dealer, after confirming the model of your
separately sold replacement air filter. (See "Optional Parts" on Vol.2 10 .)
1
Turn off the projector, and unplug the power cord. Prepare a
new air filter (one specified for your projector)
2
Remove the air filter cover and air filter
3
Insert the new filter, and replace the
filter cover
4
Turn on the projector power, and using the menu, reset the
filter timer
• To reset the lamp timer, from the OPTION menu, select FILTER TIME.
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for
the unit. Please carefully read "Safety Instructions", in order to care for your projector correctly.
• Do not use with air filter cover removed.
• If the air filter becomes clogged by dust or the like, internal temperature rises and could cause
malfunction. The power is automatically turned off in order to prevent the unit from overheating
internally.
28
CP-S317/327W/最終 03.5.27 2:22 PM ページ 29
OTHER CARE
Caring for the inside of the projector :
In order to ensure the safe use of your projector, please have it cleaned and inspected by
your local dealer about once every 2 years. Never try to care for the inside of the unit
yourself. Doing so is dangerous.
Caring for the lens :
Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the
lens directly with your hand.
Caring for the cabinet and remote control transmitter :
Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a
neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly
with a soft, dry cloth.
ATTENTION • Make sure to turn off the power and unplug the power cord before caring for
the unit. Please carefully read "Safety Instructions" in this manual, in order to care for your projector
correctly.
• Do not use cleaners or chemicals other than those listed above, including benzene and paint
thinner.
• Do not use aerosols or sprays.
• Do not polish or wipe with hard objects.
29
CP-S317/327W/Vol2-E責了 03.5.27 2:30 PM ページ 1
LCD Projector CP-322i
USER'S MANUAL
Vol.2 (Extended)
Thank you for purchasing this projector.
WARNING • Please read the accompanying manual “SAFETY
INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct
usage through understanding. After reading, store this instruction manual in a
safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without express
written authority.
TRADEMARK ACKNOWLEDGEMENT :
• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.
• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.
• VESA and SVGA are trademarks of the Video Electronics Standard Association.
• Windows is a registered trademark of Microsoft Corporation.
• All other trademarks are the property of their respective owners.
CONTENTS
Page
MULTIFUNCTIONAL SETTINGS ........................................................................2
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED ......7
SPECIFICATIONS .............................................................................................10
WARRANTY AND AFTER-SERVICE................................................................11
.......................................................................................
For "TECHNICAL" see the end of this manual.
1
CP-S317/327W/Vol2-E責了 03.5.27 2:30 PM ページ 2
MULTIFUNCTIONAL SETTINGS
This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT,
SCREEN, OPTION. Each of these menus is operated using the same methods.
The basic operations of these menus are as follows.
Menu screen display : Press the "MENU" button.
Menu selection
: Choose a menu name using the
/
button, and press the
button or the ENTER button.
Item selection
: Choose an item using the
/
button, and press the
button or the ENTER button.
Return menu to last previous screen: Press the
button or the ESC button.
Execution of settings and/or adjustments: Operate by using the
/
button. (For further
details, read the explanation for each separate menu.)
Initialization of settings and/or adjustments: During operation, press the RESET button.
(Note that items whose functions are
performed simultaneously with the operation
of clock phase, language selection, automatic
adjustment, etc., cannot be initialized.)
End menu operations: Press the MENU button, or do not perform any operation for
several seconds.
MAIN Menu
With the MAIN menu, the seven items shown in the Table below can be
performed.
Perform each operation in accordance with the instructions in the Table.
Item
Adjust Brightness: Light
CONTRAST
Adjust Contrast: Strong
2
⇔
Dark
⇔
Weak
Select Aspect Ratio:
At RGB Input or Hi-Vision 1125i(1035i/1080i)/750p of COMPONENT VIDEO
Input:
4:3
⇔
16:9
At VIDEO Input, S-VIDEO Input or 525i/525p/625i of COMPONENT VIDEO Input:
4:3
⇔
16:9
⇔
SMALL
• The SMALL picture may not be displayed correctly with certain input signals.
Select Picture Position (for 16:9/SMALL Picture):
TOP
⇔
CENTER
⇔
BOTTOM
GAMMA
Select Gamma Mode:
NORMAL
⇔
CINEMA
MIRROR
Select Mirror Status:
NORMAL
⇔
H:INVERT
LANGUAGE
12
: SELECT
Description
BRIGHT
PICT.POSIT.
BRIGHT
CONTRAST
ASPECT
PICT. POSIT.
GAMMA
MIRROR
LANGUAGE
Example : MAIN Menu
(BRIGHT)
MAIN Menu
ASPECT
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
⇔
⇔
DYNAMIC
V:INVERT
⇔
H&V:INVERT
Select Menu Language:
ENGLISH
⇔
FRANÇAIS
⇔
DEUTSCH
⇔
ESPAÑOL
⇔
ITALIANO
⇔
NORSK
⇔
NEDERLANDS
⇔
中文
⇔
日本語
⇔
POTUGUÊS
⇔
CP-S317/327W/Vol2-E責了 03.5.27 2:30 PM ページ 3
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
PICTURE 1 Menu
With the PICTURE 1 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
COLOR BAL R
COLOR BAL B
SHARPNESS
COLOR
TINT
12
: SELECT
Example : PICTURE1 Menu
(COLOR BAL R)
PICTURE1 Menu
Item
Description
COLOR BAL R
Adjust Red Color Balance: Dark
⇔
Light
COLOR BAL B
Adjust Blue Color Balance: Dark
⇔
Light
SHARPNESS
COLOR
TINT
⇔
Adjust Sharpness (for VIDEO/S-VIDEO): Clear
Soft
Adjust COLOR (for VIDEO/S-VIDEO/COMPONENT VIDEO):
Dark
⇔
Light
⇔
Adjust Tint (for VIDEO/S-VIDEO): Green
PICTURE 2 Menu
With the PICTURE 2 menu, the five items shown in the Table
below can be performed.
Perform each operation in accordance with the instructions in the
Table.
Red
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
V POSITION
H POSITION
H PHASE
H SIZE
OVER SCAN
12
: SELECT
Example : PICTURE2 Menu
(V POSITION)
PICTURE2 Menu
Item
Description
V POSITION
Adjust Vertical Position (for RGB): Up
H POSITION
Adjust Horizontal Position (for RGB): Left
H PHASE
⇔
Down
⇔
Right
Adjust Horizontal Phase (for RGB/COMPONENT VIDEO):
Right
⇔
Left
• Adjust to eliminate flicker.
H SIZE
Adjust Horizontal Size (for RGB): Large
⇔
Small
• If the horizontal size adjustment is excessive, the image may not be displayed
correctly. In such a case, initialize H SIZE with the RESET button.
OVER SCAN
Select Over-scan Ratio (for VIDEO/S-VIDEO/COMPONENT VIDEO):
LARGE
⇔
MIDDLE
⇔
SMALL
• It is recommended to select SMALL to avoid flicker at the lower part of the
picture.
3
CP-S317/327W/Vol2-E責了 03.5.27 2:30 PM ページ 4
MULTIFUNCTIONAL SETTINGS (continued)
INPUT Menu
With the INPUT menu, the four items shown in the Table below can be
performed. With inputting of RGB IN 1 and RGB IN 2 signals, the
horizontal and vertical frequencies of the signals will be displayed on the
initial screen of the INPUT menu.
Perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
AUTO
VIDEO
HDTV
SYNC ON G
EXECUTE
: SELECT
Example : INPUT Menu
(AUTO)
INPUT Menu
4
Item
Description
AUTO
Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H
PHASE, and H SIZE. Use this function with the maximum window size.
Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO
mode for the current input signal. This function is active only when the AUTO
mode is selected for the item VIDEO. Refer to the description for the item
VIDEO below.
• This function may not be available with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
VIDEO
Select Mode of Signal Type (for VIDEO/S-VIDEO):
AUTO
⇔
NTSC
⇔
PAL
⇔
SECAM
⇔
NTSC4.43
⇔
M-PAL
⇔
N-PAL
Selecting AUTO mode activates and performs the AUTO function for VIDEO/SVIDEO. It automatically selects the proper mode from among those above.
Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g.
The image becomes irregular, or lacks color.)
• AUTO mode may not function correctly with a PAL60 signal and certain other
signals.
• The AUTO mode operation requires approximately 10 seconds.
• For COMPONENT VIDEO, the signal type is identified automatically even if
this function is inactive. For a HDTV signal, refer to the item HDTV below.
HDTV
Select HDTV Signal Mode:
1080i
⇔
1035i
• If the selected HDTV mode is incompatible with the input signal, the picture
may be distorted.
SYNC ON G
On/Off SYNC ON G Mode:
TURN ON
⇔
TURN OFF
Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode
allows reception of SYNC on G.
• In the SYNC ON G mode, the picture may be distorted with certain input
signals. In such a case, remove the signal connector so that no signal is
received and turn SYNC ON G off, and then reconnect the signal.
CP-S317/327W/Vol2-E責了 03.5.27 2:31 PM ページ 5
SCREEN Menu
With the SCREEN menu, the five items shown in the Table below can be performed.
Please perform each operation in accordance with the instructions in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
BLANK
START UP
MyScreen
MyScreen Size
MyScreen Lock
MyScreen
ORIGNAL
: SELECT
Example : SCREEN Menu
(BLANK)
SCREEN Menu
Item
Description
BLANK
Selection of BLANK Screen:
MyScreen
⇔
ORIGINAL
⇔
. .
⇔
.
.
⇔
. .
The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen
has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the
“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).
MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen
(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
Option screens: Various colored non-patterned (plain) screens displayed within the Menus.
• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color
screen several minutes after being displayed.
START UP
Selection of START UP Screen:
MyScreen
⇔
ORIGINAL
⇔
TURN OFF
The START UP Screen may be voluntarily selected. The START UP Screen is displayed when
no signal has been inputted, or when spec signals are being inputted.
MyScreen: Using the MyScreen category (see this Table, below), one can register a
desired screen (or screens). At the time of factory shipment, this is set as a non-patterned
(plain) blue color screen.
ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).
TURN OFF: A non-patterned (plain) blue color screen.
• The MyScreen and the ORIGINAL Screen will each change to the BLANK Screen several
minutes after being displayed.
MyScreen
Registration of MyScreen:
When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen
and the START UP Screen is displayed. When operations are performed in accordance with this Menu,
one can “cut” and register desired screens from among the received images within the display.
1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or
RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the
picture becomes static (no longer moves), and a frame for picture cutting, as well as the message
that follows below, appear. Please press the button when the screen you want to register is
currently being displayed.
2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)
button will eliminate the static state of the picture, and operations can be performed again from operation 1.
The frame can be moved using the
,
,
,
buttons. After designating the screen
you want to register, pressing the ENTER button will initiate screen registration. The registration
process takes approximately 1 minute to complete.
3. When the registration has been completed, the screen of the registered MyScreen, plus the
message, “MyScreen registration is finished,” will be displayed for several seconds, after which
the operation is terminated.
MyScreen Size
Selection of MyScreen display size:
x1
⇔
FULL
MyScreen Lock
Invalidation of MyScreen registration function:
TURN ON
⇔
TURN OFF
When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in
this way, one can prohibit rewrites (“writeovers”) of the MyScreen.
5
CP-S317/327W/Vol2-E責了 03.5.27 2:31 PM ページ 6
MULTIFUNCTIONAL SETTINGS (continued)
OPTION Menu
With the OPTION menu, the five items shown in the Table below
can be performed.
Please perform each operation in accordance with the instructions
in the Table.
MENU
MAIN
PICTURE-1
PICTURE-2
INPUT
SCREEN
OPTION
VOLUME
AUTO OFF
WHISPER
LAMP TIME
FILTER TIME
12
: SELECT
Example : OPTION Menu
(VOLUME)
OPTION Menu
Item
VOLUME
6
Description
Adjust Volume: High
⇔
Low
AUTO OFF
Adjust AUTO OFF Time:
Long (MAX. 99 min.)
⇔
Short (Min. 1 min.)
⇔
(DISABLE: 0 min.)
The system automatically enters the standby mode if no signal is received
within the set time. This function is inactive when DISABLE (0 min.) is selected.
WHISPER
Select WHISPER Mode:
NORMAL
⇔
WHISPER
When WHISPER is selected the WHISPER mode is activated. In the WHISPER
mode, acoustic noise and screen brightness are reduced.
LAMP TIME
Refer to LAMP TIME: When set, this function displays the total time the
projector lamp has been used since new.
Reset LAMP TIME [Use this function only when the lamp has been replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the lamp with a
new lamp, select RESET on the menu with the
button.
• Do not reset the lamp time unless you have replaced the lamp. And, always
reset the lamp time when replacing the lamp. The message functions will not
operate properly if the lamp time is not reset correctly.
• Before replacing the lamp, carefully read the descriptions headed "THE
LAMP".
FILTER TIME
Refer to FILTER TIME: This function displays the total time the air-filter has
been used since new.
Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:
Depress the RESET button for at least 3 seconds while lamp time is being
displayed. The reset menu will then appear. After you replace the filter, select
RESET on the menu with the
button.
DEFAULT
⇔
CANCEL
• Do not reset the filter time unless you have cleaned or replaced the filter. And,
always reset the filter time when cleaning or replacing the filter. The message
functions will not operate properly if the filter time is not reset correctly.
• Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".
CP-S317/327W/Vol2-E責了 03.5.27 2:31 PM ページ 7
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED
Related Messages
When the unit's power is ON, messages such as those shown below may be displayed. When
any such message is displayed on the screen, please respond as described below.
Message
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
(Note 1)
Description
Lamp usage time is approaching 2,000 hours. (Note 2)
Preparation of a new lamp, and an early lamp change, is
recommended. After you have changed the lamp, please be
sure to reset the lamp timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER ** hr.
(Note 1)
Lamp usage time is approaching 2,000 hours. A lamp change
within ** hours is recommended. (Note 2)
When lamp usage reaches 2,000 hours, the power will
automatically be turned OFF. Please change the lamp by
referring to “THE LAMP” in Vol.1 (Basic). After you have
changed the lamp, please be sure to reset the lamp
timer.
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIMER.
THE POWER WILL TURN OFF
AFTER 0 hr.
As lamp use has reached 2,000 hours, the power will soon be
automatically turned OFF. (Note 2)
Please immediately turn the power OFF, and follow the
instructions in the “THE LAMP” section of the separate booklet,
Vol.1 (Basic).
After you have changed the lamp, please be sure to reset the
lamp timer.
CLEAN THE AIR FILTER
AFTER CLEANING AIR FILTER,
RESET THE FILTER TIMER.
NO INPUT IS DETECTED
ON ***
A note of precaution when cleaning the air filter.
After cleaning the filter, operate FILTER TIME of the OPTION
Menu, and perform reset of the filter timer.
There is no input signal.
Please confirm the signal input connection, and the status of the
signal source.
The horizontal or vertical wavelength of the inputted signal is
SYNC IS OUT OF RANGE
outside of the response parameters of this unit. Please confirm
ON *** fH *****kHz fV *****Hz the specs for this unit or the signal source specs.
The internal portion temperature is rising. Please turn the power
OFF, and allow the unit to cool down for approximately 20
minutes. After having confirmed the following items, then please
CHECK THE AIR FLOW
resent the power to ON.
• Is there blockage of the air passage aperture?
• Is the air filter dirty?
• Does the peripheral temperature exceed 35°C?
NOTES
Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be
reappeared every time the power is turned ON.
Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of
usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped
with an automatic shut-down function, such that the power will automatically be turned OFF
when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp
types, there are major differences in product lifetimes; a lamp may thus fail to light even prior
to the functioning of the automatic shut-down function of this unit.
7
CP-S317/327W/Vol2-E責了 03.5.27 2:31 PM ページ 8
Regarding the Indicator Lamps
Lighting and flashing of the POWER indicator, the LAMP indicator, and the
TEMP indicator have the meanings as described in the Table below.
Please respond in accordance with the instructions within the Table.
POWER
indicator
LAMP
indicator
TEMP
indicator
The orange Turned OFF Turned OFF
lamp is lighted (Not lighted) (Not lighted)
Description
The STANDBY mode is set
Flashing of the green lamp
Turned OFF
Turned OFF
The unit is warming up. Please wait.
The green lamp is lighted
Turned OFF
Turned OFF
The unit is in an ON state. Ordinary operations may be performed.
Flashing of the orange lamp
Turned OFF
Turned OFF
Blinking of the
red lamp
-
-
The red lamp
Turned
OFF
The unit is cooling down. Please wait.
The unit is cooling down. Please wait.
A certain error has been detected. Wait until the POWER indicator lamp has finished
flashing, and then perform the proper response measure using the item descriptions
below as reference.
The lamp does not light.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please change the lamp.
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp
is lighted, or
blinks
The red lamp is
lighted, or
blinks
The green lamp
is lighted
The green
lamp is lighted
is lighted
Blinking of the
red lamp
Turned
OFF
Either there is no lamp and/or lamp cover, or either of these has not been properly fixed
(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has
sufficiently cooled down, please make confirmation of the attachment state of the lamp and
lamp cover. After performing any needed maintenance, turn the power ON again; if the same
display is displayed, then please contact a sales store or a service company.
The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the
main unit has cooled down, please make confirmation that no foreign matter has become caught in
the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display
red lamp
is displayed, then please contact a sales store or a service company.
There is a possibility that the interior portion has become heated. Turn the power OFF and wait
approximately 20 minutes. After the main unit has cooled down, please confirm whether or not
Turned The red lamp is there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or
not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,
lighted
OFF
turn the power ON again; if the same display is displayed, then please contact a sales store or a
service company.
There is a possibility that the interior portion has become overcooled. Please use the unit within
Alternative blinking
the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,
turn the power ON again; if the same display is displayed, then please contact a sales store or a
with the red lamp
service company.
Turned
OFF
Blinking of the
Simultaneous blinking
with the red lamp
This is a notification that it is time to clean the filter.
After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform
reset of the FILTER TIME.
NOTE
When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,
and the indicator lamps may also be turned OFF. Press the “ ○” (power OFF) side of the main power switch, and wait
for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently
cooled down.
8
CP-S317/327W/Vol2-E責了 03.5.27 2:31 PM ページ 9
WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)
Phenomena That May Easily Be Mistaken for Machine Defects
Before requesting repair, check in accordance with the following chart.
If the situation cannot be corrected, then contact your dealer.
Phenomenon
Power does not
come ON
No sound or
pictures are
outputted
Pictures are
displayed, but no
sounds are heard
Sounds are
heard, but no
pictures are
displayed
Colors have a fadedout appearance
Color tone is poor
Pictures appear
dark
Pictures appear
blurry
Cases not involving a machine defect
Items to be confirmed
Reference
Page(s)
The main power source is not ON.
Turn on the main power.
The electrical power cord is not plugged in.
The input changeover settings
are mismatched.
Correctly connect the power cord.
Be sure to press the “O” (power OFF) side
of the main power switch, and leave this OFF
for approximately 20 minutes. After the unit Vol.1-14
has sufficiently cooled down, turn ON the
power source.
Select the input signal, and
Vol.1-15
correct the settings.
No signal is being inputted.
Correctly connect the connection cord.
Vol.1-10, 11
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
Vol.1-10, 11
The volume setting has been set at (or
adjusted to) an extremely low level.
Adjust the VOLUME setting to a higher level.
Vol.1-17
The MUTE mode is the current setting.
Press the MUTE button to release
Vol.1-17
(change) the MUTE mode setting.
The electrical wiring to this unit
is not correctly connected.
Correctly connect the connection cord.
Vol.1-10, 11
The brightness setting has been set at
(or adjusted to) an extremely low level.
Adjust the BRIGHT setting to a
brighter level.
Vol.2-2
The lens cap has not been removed.
Remove the lens cap.
Vol.1-14
Color depth setting or color tone setting
Perform picture adjustments by changing the
COLOR BAL R, the COLOR BAL B, and/or the Vol.2-3
TINT settings, etc.
The brightness setting and/or contrast
setting has not been properly adjusted.
Perform picture adjustments by changing the
Vol.2-2
BRIGHT and/or CONTRAST settings, etc.
The WHISPER mode is the current
setting.
Change (by releasing) from the
Vol.2-6
WHISPER mode.
Lamp is approaching the end of its
product lifetime.
Exchange the old lamp with a new
Vol.1-25, 26
lamp.
Either the FOCUS setting or the H
PHASE is not properly adjusted.
Adjust the FOCUS and H PHASE settings.
The main power source has been
interrupted during operation, such as by
a power outage (blackout), etc.
Vol.1-3, 14
Vol.1-15
Vol.2-3
NOTE
Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and
such do not constitute or imply a machine defect.
9
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 1
TECHNICAL
SIGNAL CONNECTOR PIN ASSIGNMENT
RGB IN [1]/[2]
RGB OUT
S-VIDEO
D-sub 15-pin Shrink
Pin No
Signal
Mini Din 4-pin
Pin No
Signal
1
Video input Red
9
-
2
3
4
5
6
7
8
Video input Green
Video input Blue
Ground
Ground Red
Ground Green
Ground Blue
10
11
12
13
14
15
Ground
RGB IN [1]: SDA (DDC)
RGB IN [2]:
RGB OUT :
H. sync./ Composite sync.
Vertical sync
RGB IN [1]: SCL (DDC)
RGB IN [2]:
RGB OUT :
signal
Terminal
RGB signal
input
RGB IN(1、2)
Audio
signal input
Signal output
AUDIO IN(R、L)
RGB OUT
2
3
Ground
4
Ground
-
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
1.0Vp-p, 75Ω terminator, RCA jack
Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.286Vp-p (NTSC, burst signal),75Ω terminator
0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator
Mini DIN 4-pin jack
S-VIDEO IN
COMPONENT
VIDEO
1
Color:
0.286Vp-p (NTSC, burst signal),
75Ω terminator
0.3Vp-p (PAL/SECAM, burst signal),
75Ω terminator
Brightness:
1.0Vp-p, 75Ω terminator
Specification
VIDEO IN
Video signal
input
Mini Din 4-pin
Pin No Signal
Y
1.0 Vp-p, 75 Ω Terminator (Positive)
CB/PB
0.7 Vp-p, 75 Ω Terminator (Positive)
CR/PR
0.7 Vp-p, 75 Ω Terminator (Positive)
200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
1
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 2
EXAMPLE OF COMPUTER SIGNAL
Display mode
Resolution
H×V
fH (kHz)
fV (Hz)
Rating
Signal mode
CP-S318
CP-X328
720 × 400
37.9
85.0
VESA
TEXT
Zoom in
Zoom in
640 × 480
31.5
59.9
VESA
VGA (60Hz)
Zoom in
Zoom in
640 × 480
35.0
66.7
Mac13"mode
Zoom in
Zoom in
640 × 480
37.9
72.8
VESA
VGA (72Hz)
Zoom in
Zoom in
640 × 480
37.5
75.0
VESA
VGA (75Hz)
Zoom in
Zoom in
640 × 480
43.3
85.0
VESA
VGA (85Hz)
Zoom in
Zoom in
800 × 600
35.2
56.3
VESA
SVGA (56Hz)
Zoom in
800 × 600
37.9
60.3
VESA
SVGA (60Hz)
Zoom in
800 × 600
48.1
72.2
VESA
SVGA (72Hz)
Zoom in
800 × 600
46.9
75.0
VESA
SVGA (75Hz)
Zoom in
800 × 600
53.7
85.1
VESA
SVGA (85Hz)
832 × 624
49.7
74.5
1024 × 768
48.4
60.0
1024 × 768
56.5
70.1
1024 × 768
60.0
1024 × 768
1152 × 864
Zoom in
Mac16"mode
Zoom out
Zoom in
VESA
XGA (60Hz)
Zoom out
VESA
XGA (70Hz)
Zoom out
75.0
VESA
XGA (75Hz)
Zoom out
68.7
85.0
VESA
XGA (85Hz)
Zoom out
67.5
75.0
VESA
SXGA (75Hz)
Zoom out
Zoom out
1280 × 960
60.0
60.0
VESA
SXGA (60Hz)
Zoom out
Zoom out
1280 × 1024
64.0
60.0
VESA
SXGA (60Hz)
Zoom out
Zoom out
1280 × 1024
80.0
75.0
VESA
SXGA (75Hz)
Zoom out
Zoom out
1280 × 1024
91.2
85.0
VESA
SXGA (85Hz)
Zoom out
Zoom out
1600 × 1200
75.0
60.0
VESA
UXGA (60Hz)
Zoom out
Zoom out
NOTE • Some computers may have multiple display screen modes. Use of some
of these modes will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this
projector to a computer.
• Depending on the input signal, full-size display may not be possible in some cases.
Refer to the number of display pixels above.
• This projector will display up to UXGA (1600X1200) resolution signals but the image
will be rescaled to the native resolution of the projector. Best display performance is
achieved when the signal input resolution is the same as the native resolution of the
projector.
• The image may not be displayed correctly when the input sync. signal is “Composite
Sync.” or “Sync. on G”.
2
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 3
INITIAL SET SIGNALS
The following signals are used for the initial settings.
The signal timing of some computer models may be different. In such case, refer to
adjust the V.POSIT and H.POSIT of the menu.
Back porch b
Front porch d
Display interval c
Back porch b
Front porch d
Display interval c
DATA
DATA
HSYNC
VSYNC
Sync a
Computer /
Signal
Sync a
Horizontal signal timing (µs)
TEXT
a
2.0
b
3.0
c
20.3
d
1.0
Computer /
Signal
Vertical signal timimg (lines)
TEXT
a
3
b
42
c
400
d
1
VGA (60Hz)
3.8
1.9
25.4
0.6
VGA (60Hz)
2
33
480
10
Mac 13"mode
2.1
3.2
21.2
2.1
Mac 13"mode
3
39
480
3
VGA (72Hz)
1.3
3.8
20.3
1.0
VGA (72Hz)
3
28
480
9
VGA (75Hz)
2.0
3.8
20.3
0.5
VGA (75Hz)
3
16
480
1
VGA (85Hz)
1.6
2.2
17.8
1.6
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2.0
3.6
22.2
0.7
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
3.2
2.2
20.0
1.0
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
2.4
1.3
16.0
1.1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
1.6
3.2
16.2
0.3
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
1.1
2.7
14.2
0.6
SVGA (85Hz)
3
27
600
1
Mac 16"mode
1.1
3.9
14.5
0.6
Mac 16"mode
3
39
624
1
XGA (60Hz)
2.1
2.5
15.8
0.4
XGA (60Hz)
6
29
768
3
XGA (70Hz)
1.8
1.9
13.7
0.3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
1.2
2.2
13.0
0.2
XGA (75Hz)
3
28
768
1
XGA (85Hz)
1.0
2.2
10.8
0.5
XGA (85Hz)
3
36
768
1
1152×864 (75Hz)
1.2
2.4
10.7
0.6
1152×864 (75Hz)
3
32
864
1
1280×960 (60Hz)
1.0
2.9
11.9
0.9
1280×960 (60Hz)
3
36
960
1
1280×1024 (60Hz)
1.0
2.3
11.9
0.4
1280×1024 (60Hz)
3
38
1024
1
1280×1024 (75Hz)
1.1
1.8
9.5
0.2
1280×1024 (75Hz)
3
37
1024
2
1280×1024 (85Hz)
1.0
1.4
8.1
0.4
1280×1024 (85Hz)
3
44
1024
1
1600×1200 (60Hz)
1.2
1.9
9.9
0.4
1600×1200 (60Hz)
3
46
1200
1
3
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 4
CONNECTION TO THE MOUSE CONTROL
Projector
ADB Mouse
DATA
CONTROL Terminal
D-sub 15-pin shrink jack
RTS
2 3 4 5
6 7 8 9 10
11 12 13 14 15
1
+5V
GND
Serial Mouse
1
2
3
4
SEL0
RTS
D-sub 15-pin shrink jack
1 2 3 4 5
7 8 9 10
11 12 13 14 15
GND
TD
ADB
(POWER ON)
+5V
GND
Mouse jack
Mini DIN 4-pin
3
4
1
2
Projector
CONTROL Terminal
6
Computer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
1
2
3
4
5
6
7
8
9
Mouse jack
D-sub 9-pin
1
2
6
3
5
4
8
7
9
USB Mouse
USB jack
(B type)
2
3
Computer
Projector
+5V 1
1
1
—DATA 2
2 —DATA
+DATA 3
3
GND 4
4
+5V
USB jack
(A type)
+DATA
1
4 GND
2
3
4
USB cable
PS/2 Mouse
CONTROL Terminal
CLK
DATA
D-sub 15-pin shrink jack
SEL0
RTS
2 3 4 5
7 8 9 10
11 12 13 14 15
+5V
GND
6
4
Projector
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
DATA
GND
+5V
CLK
Mouse jack
Mini DIN 6-pin
6
5
3
4
2
1
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 5
RS-232C COMMUNICATION
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the
projector power supply.
Projector
Control jack
D-sub 15-pin shrink jack
Computer
1
2
3
4
5
SELO 6
RTS 7
8
9
GND 10
11
12
RD 13
TD 14
15
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
DTS
RI
RS-232C jack
D-sub 9-pin
2
1
6
3
7
4
8
5
9
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0
byte_1
byte_2
Action
low
byte_3
Type
high
low
byte_4
byte_5
Setting code
high
low
high
Action (byte_0 - 1)
Action
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT
Increment setup value by 1.
5
DECREMENT
Decrement setup value by 1.
6
EXECUTE
Run a command.
5
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 6
RS-232C COMMUNICATION (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +
setting code (2 bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+
type (2 bytes) +‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+
type (2 bytes) +‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during
other works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
When the command sent by the projector cannot be practiced, the the error code ‘1cH’
+‘xxxxH’ is returned.
When the data length is greater than indicated by the data length code, the projector will
ignore the excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an
error code will be returned to the projector.
NOTE • Operation cannot be guaranteed when the projector receives an
undefined command or data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the
lamp is lit. Ignore this data.
• Commands are not accepted during warm-up.
6
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 7
Command data chart
Names
Blank Color
Mirror
Operation type
Set
Set
Type
Setting code
Blue
BE EF
03
06 00
CB D3
01 00
00 30
03 00
White
BE EF
03
06 00
6B D0
01 00
00 30
05 00
Black
BE EF
03
06 00
9B D0
01 00
00 30
06 00
MyScreen
BE EF
03
06 00
FB CA
01 00
00 30
20 00
ORIGNAL
BE EF
03
06 00
FB E2
01 00
00 30
40 00
Get
BE EF
03
06 00
08 D3
02 00
00 30
00 00
Normal
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
H Inverse
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V lnverse
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V Inverse
BE EF
03
06 00
37 D2
01 00
01 30
03 00
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Normal
BE EF
03
06 00
83 D2
01 00
02 30
00 00
Freeze
BE EF
03
06 00
13 D3
01 00
02 30
01 00
Get
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
ORIGNAL
BE EF
03
06 00
0B D2
01 00
04 30
00 00
OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
MyScreen
BE EF
03
06 00
CB CB
01 00
04 30
20 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
English
BE EF
03
06 00
F7 D3
01 00
05 30
00 00
Français
BE EF
03
06 00
67 D2
01 00
05 30
01 00
Deutsch
BE EF
03
06 00
97 D2
01 00
05 30
02 00
Español
BE EF
03
06 00
07 D3
01 00
05 30
03 00
Italiano
BE EF
03
06 00
37 D1
01 00
05 30
04 00
Norsk
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
Nederlands
BE EF
03
06 00
57 D0
01 00
05 30
06 00
Português
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
日本語
BE EF
03
06 00
37 D4
01 00
05 30
08 00
中文
BE EF
03
06 00
A7 D5
01 00
05 30
09 00
Get
Freeze
Startup
Language
Magnify
Set
Set
Set
Command data
Header
CRC
Action
BE EF
03
06 00
57 D5
01 00
05 30
0A 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
BE EF
03
06 00
CB D3
05 00
07 30
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Brightness
Reset
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
Contrast Reset
Execute
BE EF
03
06 00
A4 D2
06 00
01 70
00 00
V.Position
Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
Auto off
7
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 8
Command data chart (continued)
Names
Operation type
H.Position Reset
Execute
BE EF
03
H.Size Reset
Execute
BE EF
Color Balance
R Reset
Execute
Color Balance
B Reset
Command data
Header
CRC
Action
Type
Setting code
06 00
IC D3
06 00
03 70
00 00
03
06 00
68 D2
06 00
04 70
00 00
BE EF
03
06 00
94 D3
06 00
05 70
00 00
Execute
BE EF
03
06 00
D0 D3
06 00
06 70
00 00
Sharpness Reset
Execute
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
Color Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
Tint Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
Keystone_V Reset
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
Keystone_H Reset
Execute
BE EF
03
06 00
98 D8
06 00
20 70
00 00
Auto Adjust
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
Lamp Time Reset
Execute
BE EF
03
06 00
58 DC
06 00
30 70
00 00
Filter Time Reset
Execute
BE EF
03
06 00
98 C6
06 00
40 70
00 00
off
BE EF
03
06 00
FB D8
01 00
20 30
00 00
on
BE EF
03
06 00
6B D9
01 00
20 30
01 00
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
Blank on/off
Set
Get
Error Status
Get
(Example of Return)
00 00
01 00
(Normal) (Cover-error)
04 00
05 00
(Temp-error) (Air flow-error)
Power
Set
Input Source
06 00
(Lamp-Time-over)
03 00
(Lamp-error)
07 00
(Cool-error)
0800
(Filter-Error)
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
2A D3
BA D2
19 D3
01 00
01 00
02 00
00 60
00 60
00 60
00 00
01 00
00 00
RGB1
BE EF
03
06 00
FE D2
01 00
00 20
00 00
RGB2
BE EF
03
06 00
3E D0
01 00
00 20
04 00
Video
BE EF
03
06 00
6E D3
01 00
00 20
01 00
SVideo
BE EF
03
06 00
9E D3
01 00
00 20
02 00
Component
BE EF
03
06 00
AE D1
01 00
00 20
05 00
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
OFF
ON
Get
Set
02 00
(Fan-error)
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
Normal
BE EF
03
06 00
46 D3
01 00
02 20
00 00
Mute
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
Volume
Set
Mute
Brightness
8
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 9
Names
Operation type
Command data
Header
CRC
BE EF
03
06 00
FD D3
02 00
04 20
00 00
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
Get
BE EF
03
06 00
01 D2
02 00
05 20
00 00
Increment
BE EF
03
06 00
67 D2
04 00
05 20
00 00
Decrement
BE EF
03
06 00
B6 D3
05 00
05 20
00 00
Get
BE EF
03
06 00
45 D2
02 00
06 20
00 00
Increment
BE EF
03
06 00
23 D2
04 00
06 20
00 00
Decrement
BE EF
03
06 00
F2 D3
05 00
06 20
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
Color Balance B
Keystone_V
Get
BE EF
03
06 00
E9 D0
02 00
0B 20
00 00
Increment
BE EF
03
06 00
8F D0
04 00
0B 20
00 00
Decrement
BE EF
03
06 00
5E D1
05 00
0B 20
00 00
4:3
BE EF
03
06 00
9E D0
01 00
08 20
00 00
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
Small
BE EF
03
06 00
FE D1
01 00
08 20
02 00
BE EF
03
06 00
AD D0
02 00
08 20
00 00
Default
BE EF
03
06 00
62 D1
01 00
09 20
00 00
Bottom
BE EF
03
06 00
F2 D0
01 00
09 20
01 00
Top
BE EF
03
06 00
02 D0
01 00
09 20
02 00
Get
BE EF
03
06 00
51 D1
02 00
09 20
00 00
Keystone_H
Set
Get
V.Position
H.Position
H.Size
H.Phase
Sharpness
Color
Setting code
Get
Color Balance R
Picture
Position at
16 : 9 or Small
Type
Increment
Contrast
Aspect
Action
Set
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
00 00
Get
Increment
Decrement
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
49 83
2F 83
FE 82
02 00
04 00
05 00
03 21
03 21
03 21
00 00
00 00
00 00
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
9
CP-S318/328W/TECHNICAl責了 03.5.27 2:39 PM ページ 10
Command data chart (continued)
Names
Operation type
Command data
Header
Type
Setting code
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
Auto
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
Tint
Set
CRC
Action
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC 4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
BE EF
03
06 00
0D 73
02 00
00 22
00 00
1080i
BE EF
03
06 00
F2 73
01 00
05 22
00 00
1035i
BE EF
03
06 00
62 72
01 00
05 22
01 00
BE EF
03
06 00
C1 73
02 00
05 22
00 00
off
BE EF
03
06 00
CB D0
01 00
08 30
01 00
on
BE EF
03
06 00
5B D1
01 00
08 30
00 00
Get
BE EF
03
06 00
68 D1
02 00
08 30
00 00
NORMAL
BE EF
03
06 00
3B 23
01 00
00 33
00 00
WHISPER
BE EF
03
06 00
AB 22
01 00
00 33
01 00
Get
BE EF
03
06 00
08 23
02 00
00 33
00 00
NORMAL
BE EF
03
06 00
C7 F0
01 00
A1 30
00 00
CINEMA
BE EF
03
06 00
57 F1
01 00
A1 30
01 00
DYNAMIC
BE EF
03
06 00
A7 F1
01 00
A1 30
02 00
Get
Video Format
Get
Set
HDTV
Get
Set
Sync on G
Set
WHISPER
Set
GAMMA
Set
BE EF
03
06 00
F4 F0
02 00
A1 30
00 00
Large
BE EF
03
06 00
C2 71
01 00
09 22
02 00
Middle
BE EF
03
06 00
32 71
01 00
09 22
01 00
Small
BE EF
03
06 00
A2 70
01 00
09 22
00 00
Over Scan
Get
BE EF
03
06 00
91 70
02 00
09 22
00 00
Full
BE EF
03
06 00
43 D6
01 00
12 30
00 00
X1
BE EF
03
06 00
D3 D7
01 00
12 30
01 00
BE EF
03
06 00
70 D6
02 00
12 30
03 00
off
BE EF
03
06 00
3B EF
01 00
C0 30
00 00
on
Set
MyScreen Size
Get
Set
MyScreen Lock
10
BE EF
03
06 00
AB EE
01 00
C0 30
01 00
Get
BE EF
03
06 00
08 EF
02 00
C0 30
00 00
Lamp Time
Get
BE EF
03
06 00
C2 FF
02 00
90 10
00 00
Filter Time
Get
BE EF
03
06 00
C2 F0
02 00
A0 10
00 00
REGULATORY- NOTICES 03.5.27 2:23 PM ページ 1
REGULATORY NOTICES
FCC Statement Warning
WARNING: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements
of FCC (Federal Communication Commission) equipment provided that the
following conditions are met.
The cables may have to be used with the core set to the projector side. Use
the cables which are included with the projector or specified.
STANDBY/ON
INPUT
KEYSTONE
RESET
LANP
POWERTENP
Core
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.
Pour les utilisateurs au Canada
AVIS: Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du
Canada.
LIMITED WARRANTY
Boxlight (“Boxlight”) warrants that each Boxlight CP-322i & CP-634i (“the Product”) sold hereunder will conform to and
function in accordance with the written specifications of Boxlight. Said limited warranty shall apply only to the first person or entity that purchases the Product for personal or business use and not for the purpose of distribution or resale. Said
warranty shall continue for a period of two (2) years from the date of such purchase. The standard limited warranty
excludes the lamps in projectors after 120 days or 500 hours (whichever comes first) and the accessories after one year.
Boxlight does not warrant that the Product will meet the specific requirements of the first person or entity that purchases
the Product for personal or business use. Boxlight’s liability for the breach of the foregoing limited warranty is limited to
the repair or replacement of the Product or refund of the purchase price of the Product, at Boxlight’s sole option.
Replacement Product may be re-furbished in “like-new” condition, at Boxlight’s sole discretion. To exercise the
Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost and expense, to
Boxlight or to any authorized Boxlight service center, and the Product must be accompanied by a written letter explaining
the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and (iii) the model and serial number
of the Product. When sending your unit in for repair, please ship your unit in its original packing material or a Boxlight
approved ATA Shipping Case, or have a professional packaging company pack the unit. Please insure your shipment for
its full value. A return authorization number, issued by the Boxlight Customer Service department, must also be
clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
Boxlight shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress (unusual physical and electrical stress includes
unusually long operation, exposure to smoke and other airborne contaminants), unauthorized modifications, tampering,
alterations, or service other than by Boxlight or its authorized agents, causes other than from ordinary use or failure to
properly use the Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING
WARRANTY SHALL NOT BE EXTENDED, ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT
SIGNED BY BOXLIGHT. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY MAY LAST, SO SUCH LIMITATIONS MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT BOXLIGHT’S LIABILITY WHETHER IN CONTRACT, IN TORT,
UNDER ANY WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE
AMOUNT OF THE PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL
BOXLIGHT BE LIABLE
FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST
REVENUES OR LOST SAVINGS. THE PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN
LIMITING BOXLIGHT’S LIABILITY. NO ACTION, REGARDLESS OF FORM, ARISING OUT OF THE
AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT BY PURCHASER MORE THAN ONE YEAR
AFTER THE CAUSE OF ACTION HAS ACCRUED. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR
EXCLUSION MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
Boxlight Corporation
19332 Powder Hill Place
Poulsbo, WA 98370-7407 USA
USA and Canada 800.762.5757
International +1.360.779.7901
www.boxlight.com