Chicago Pneumatic SD25 Specifications

Valve terminals type 34 MPA-L
-V- New
Valve terminals type 34 MPA-L
Key features
Innovative
• Slim high-performance valves
in a sturdy metal housing
• Flow rates up to 360 l/min
• Wide range of electrical connection
options for multi-pin plug: Sub-D,
flat cable or terminal strip
• Connection to the electrical
peripherals CPX with a wide range
of communication options
• Freely configurable push-in
connectors
2
Versatile
• Modular system offering a range of
configuration options
• Freely extendable system with
individual sub-bases and modular
tie rods
• Up to 32 solenoid coils
• Conversions and extensions
possible at a later date
• Air supply can be extended by
additional pressure zones via
supply modules
• Wide range of pressures
–0.9 … 10 bar
• Wide range of valve functions
Internet: www.festo.com/catalog/...
Reliable
• High output reserves thanks to
large pneumatic cross sections and
venting with high flow rates
• Resilient thanks to high mechanical
rigidity
• Lightweight and low-cost polymer
components
• Fast troubleshooting thanks to LEDs
on the valves
• Easy to service thanks to
replaceable valves and electronic
modules
• Manual override either
non-detenting, detenting or secured
against unauthorised activation
(covered)
• Durable thanks to tried-and-tested
piston spool valves
Easy to assemble
• Fast and reliable in-house assembly
using individual components or
delivered as a ready-to-install and
tested unit
• Lower selection, ordering,
installation and commissioning
costs
• Secure mounting on wall or H-rail
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features
Reliable operation:
Non-detenting/detenting or covered manual override
Width 10 mm
Reduced downtimes:
LED switching status display
Adaptable:
Selector in the end plate for defining
the pilot air supply (internal or external)
Pneumatic interface to CPX
CPX diagnostic interface
for handheld devices
Space-saving:
Slim valves and flat plate silencers
Simple electrical connections
– Multi-pin plug, fieldbus connections
– Control block, CPX
Practical:
Pre-assembled QS cartridge fittings
Quick mounting:
Directly using screws or on a H-rail
Flexible:
32 valve positions/32 solenoid coils
Modular:
Pressure zone creation, additional
exhaust and supply ports possible using
supply module
Safe:
Operating voltage connection, outputs
and valves can each be switched off
separately
Equipment options
Valve functions
• 5/2-way valve, single solenoid
• 5/2-way valve, double solenoid
• 2x 3/2-way valve,
normally open
• 2x 3/2-way valve,
normally closed
• 2x 3/2-way valve,
1x normally open,
1x normally closed
• 5/3-way valve,
mid-position pressurised
• 5/3-way valve,
mid-position closed
• 5/3-way valve,
mid-position exhausted
• 2x 2/2-way valve,
1x normally closed,
1x normally closed, reversible
• 2x 2/2-way valve,
normally closed
• 1x 3/2-way valve,
normally closed,
external compressed air supply
• 1x 3/2-way valve,
normally open,
external compressed air supply
All valves have the same compact
dimensions with an overall length of
107 mm and a width of 10.5 mm.
• Any compressed air supply
(max. 8 supply modules)
• Creation of pressure zones
• Modular, individually extendable
tie rods
• Single valves or combinations of
four valves
• Tubing size at each connection
freely selectable
Special features
• Max. 32 valve positions/
max. 32 solenoid coils
• Parallel, modular valve linking
• Electrical interlinking with
integrated holding current
reduction
Online via: www.festo.com/us/engineering
2D/3D CAD data
Valve terminal selection
Valve terminal configurator
The appropriate MPA-L valve terminal
can be chosen quickly and easily
using the online catalogue. This
includes a convenient valve terminal
configurator, which makes it much
simpler to order the right product.
2012/06 – Subject to change
The valve terminals are fully
assembled according to your order
specification and are individually
tested. This reduces assembly and
installation time to a minimum.
You order a valve terminal type 34
using the order code.
Ordering system for type 34
Internet: mpal
Ordering system for CPX
Internet: cpx
Internet: www.festo.com/catalog/...
You can request the CAD data for
a valve terminal you have configured.
To do so, start the product search as
described above. Go to the shopping
basket and click on the CAD icon
(compass). On the next page you can
generate a 3D preview or request
another data format of your choice by
e-mail.
3
-V- New
Valve terminals type 34 MPA-L
Key features
Multi-pin plug connection
The signal flow from the controller
to the valve terminal takes place via
a pre-assembled or self-assembled
multi-wire cable to the multi-pin plug
connection, which substantially
reduces installation time.
The valve terminal can be equipped
with max. 32 solenoid coils. This
corresponds to 2 to 32 valves.
Versions
• Sub-D connection
– Pre-assembled multi-pin cable
– Multi-pin cable for self-assembly
• Flat cable connection
• Terminal strip connection
An integrated fieldbus node manages
communication with a higher-order
PLC. This enables a space-saving
pneumatic and electronic solution.
Valve terminals with fieldbus
interfaces can be configured with up
to 32 sub-bases.
The CPX terminal also enables the
integration of digital and analogue
electrical inputs and outputs,
pressure sensors and controllers for
pneumatic or electric positioning
axes.
A detailed description of the extensive
functionality can be found in the
documentation for the CPX terminal
Internet: cpx
Fieldbus protocols/CPX variants:
• Profibus DP
• ProfiNet
• Interbus
• DeviceNet
• CANopen
• CC-Link
• Ethernet/IP
• Front End Controller
Remote I/O
• Modbus/TCP
• EtherCAT
In the slave operating mode, these
valve terminals can be used for
intelligent preprocessing and are
therefore ideal modules for designing
decentralised intelligence.
In the master operating mode,
terminal groups can be designed with
many options and functions that can
autonomously control a medium-sized
machine/system.
Fieldbus connection via the CPX system
Control block connection via the CPX system
Controllers integrated in the Festo
valve terminals enable the
construction of stand-alone control
units to IP65, without control
cabinets.
4
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Peripherals overview
Modular pneumatic components
The modular design of the MPA-L
facilitates maximum flexibility right
from the planning stage and offers
maximum ease of servicing during
operation.
The system consists of sub-bases and
valves.
The sub-bases form the support
system for the valves.
They contain the connection ducts for
supplying compressed air to and
venting from the valve terminal as
well as the working lines for the
pneumatic drives for each valve.
The sub-bases are joint together via
a tie rod system. This consists of
a threaded rod, threaded sleeve and
screw. The threaded rod/sleeve
combination is selected as
appropriate to the chosen number of
individual sub-bases.
A valve terminal can be easily
extended by adding individual
sub-bases or supply modules. This is
done by inserting suitable tie rod
extenders between the threaded rod
and sleeve.
This ensures that the valve terminal
can be rapidly and reliably extended.
Note
The tie rod system for the valve
terminals MPA-L consists of at least
four sub-bases or two sub-bases
and one supply module.
Shorter valve terminals with two or
more valve positions can be
constructed without a sleeve.
Modular electrical peripherals
The mechanical connection between
the CPX modules is established using
tie rods. Two screws in the end plates
are all that are needed to assemble
the entire unit.
The tie rod ensures that the unit
resists high mechanical loads and is
therefore the mechanical backbone of
the CPX terminal.
The tie rod extension kit allows an
extra module to be added to the CPX
terminal.
The input/output modules,
connection blocks, fieldbus nodes or
control block of the CPX system are
mounted on the interlinking blocks
using four screws and can be almost
infinitely replaced or modified.
The open design allows interlinking
blocks to be replaced in assembled
state.
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
5
-V- New
Valve terminals type 34 MPA-L
Peripherals overview
Valve terminal pneumatic components
• Double solenoid valve positions
can be fitted with any valve or
a blanking plate.
The electrical interlinking modules
are available for:
• 1 or 4 single solenoid valves
• 1 or 4 double solenoid valves
The sub-bases are available
individually with one valve position or
with four valve positions.
9
• Single solenoid valve positions can
only be fitted with single solenoid
valves or a blanking plate.
aA
aJ
8
5
5
6
7
4
3
2
1
aB
aC
aD
aE
aF
bJ
bB
bD
6
bC
aI
aH
aG
bA
3
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Peripherals overview
Valve terminal pneumatic components
Designation
1
2
3
4
5
6
Plate
Plate
Cartridge fitting
Cover cap for manual override
Solenoid valve
Electrical interlinking module, 4-way
7
8
9
aJ
aA
aB
aC
aD
aE
aF
aG
aH
aI
bJ
bA
bB
bC
bD
Mounting bracket
Restrictor
Retainer for fixed restrictor
Right-hand end plate, low
Screw
Right-hand end plate, high
Inscription label
Holder for inscription label
Sub-base
Sleeve
Tie rod extender
Tie rod
Cartridge fitting
Clamp strap for cartridge fitting
Sub-base, individual
Electrical interlinking module
Supply module
Electrical interlinking module
2012/06 – Subject to change
Brief description
Page/Internet
Exhaust plate as flat plate silencer
Exhaust plate for ducted exhaust air
For supply and exhaust ports
Conversion from detenting/non-detenting to non-detenting or covered
Single solenoid
Electrical interlinking module for combination of four sub-bases, single solenoid/double
solenoid
Mounting bracket for wall mounting
Fixed restrictor for installation in duct 3 or 5 of the sub-base
Required to install the fixed restrictor
End plate with pilot air selector, with ports 12/14, 82/84
Tie rod system, connects the sub-bases
End plate with pilot air selector, with ports 1, 3, 5, 12/14, 82/84
6 x 10 mm
–
Four individual sub-bases screwed together to form one unit
Tie rod system, connects the sub-bases
For subsequent modular extension of the valve terminal
Threaded rod, clamps the sub-bases between the end plates
For working lines
–
Sub-base with one valve position
Electrical interlinking module for single sub-base, single solenoid/double solenoid
For compressed air supply/exhaust air
Electrical interlinking module for supply module, signals are passed through
41
41
44
42
38
40
Internet: www.festo.com/catalog/...
40
40
40
42
39
42
46
46
38
39
39
39
44
–
38
40
41
40
7
-V- New
Valve terminals type 34 MPA-L
Peripherals overview
Valve terminal with multi-pin plug connection
Order code:
• 34P-…
MPA-L valve terminals with multi-pin
plug connection can be expanded by
up to 32 solenoid coils/valve
positions.
The multi-pin plug connection is
removable and designed as a 9, 25 or
44-pin Sub-D connection. The
multi-pin plug connection can
alternatively be ordered as a terminal
strip (33-pin) or flat cable connection
(40-pin).
5
4
3
6
The Sub-D multi-pin plug connection,
25 and 44-pin, is available to IP40
and IP67 or with multi-pin plug cover,
without connecting cable, with
a choice of cable outlet to the side
or front.
8
7
2
Sub-D multi-pin plug connection,
25 and 44-pin, with multi-pin plug
cover with pre-assembled cable:
• 2.5 m
• 5m
• 10 m
• Variable, up to 30 m
1
Designation
Brief description
Page/Internet
1
2
3
4
5
6
7
8
Terminal strip, 33-pin, IP40
For flat cable, 40-pin, IP40
Sub-D, 25-pin
Sub-D, 9-pin, IP40
With cover, pre-assembled, connection on side, IP67
For self-assembly, connection on side, IP67
For self-assembly, connection on front, IP67
With cover, pre-assembled, connection on front, IP67
42
42
42
42
43
43
43
43
8
Multi-pin plug connection
Multi-pin plug connection
Multi-pin plug connection
Multi-pin plug connection
Connecting cable
Cover
Cover
Connecting cable
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Peripherals overview
Valve terminal with fieldbus connection, control block (electrical peripherals CPX)
Order code:
• 34P-… for the pneumatic
components
• 50E-… for the electrical
peripherals
Valve terminals with CPX interface can
be expanded by up to 32 solenoid
coils/valve positions.
This enables extensions to be
pre-assigned in a control program and
called up by means of manual
settings.
Each valve position can be equipped
with any valve or a blanking plate. The
rules for CPX apply to the equipment
that can be used in combination with
the electrical peripherals CPX.
Up to 32 valve positions can be
equipped in combination with single
solenoid valves; the maximum
number of valve positions is reduced
to 16 if only double solenoid valves
are used.
The maximum number of addresses is
set in the range 4 … 32 solenoid coils
via a selector switch.
In general:
• Digital inputs/outputs
• Analogue inputs/outputs
• Parameterisation of inputs and
outputs
• Integrated multi-featured
diagnostic system
• Preventive maintenance concepts
3
2
1
4
4
4
Designation
Brief description
Page/Internet
1
2
3
4
Fieldbus node, control block, input and output modules
Pneumatic interface for CPX terminal
Large, for left-hand end plate/pneumatic interface for CPX terminal
–
cpx
42
–
40
CPX modules
Left-hand end plate
Inscription label
H-rail mounting
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
9
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Sub-base valve
MPA-L offers a comprehensive range
of valve functions. All valves are
equipped with piston spool and
patented sealing system that
facilitates efficient sealing, a broad
pressure range and long service life.
They have a pneumatic pilot control
for optimising performance.
Air is supplied by means of pilot air
supply.
Sub-base valves can be quickly
replaced since the tubing connectors
remain on the sub-base.
This design is also particularly slim.
replaced. The mechanical sturdiness
of the sub-base guarantees good
long-term sealing.
Blanking plates can be replaced by
valves at a later date. The dimensions,
mounting points and existing
pneumatic installations remain
unchanged in this case.
Design
Valve replacement
The valves are attached to the
sub-base using two screws, which
means that they can be easily
Valve function
Circuit symbol
10
Irrespective of the valve function there
are sub-base valves with one solenoid
coil (single solenoid) or with two
solenoid coils (double solenoid or
two single solenoid valves in one
housing).
Extension
Code
Description
Position function 1-32: M
5/2-way valve, single solenoid
• Pneumatic spring return
• Reversible
• Suitable for vacuum
Position function 1-32: J
5/2-way valve, double solenoid
• Reversible
• Suitable for vacuum
Position function 1-32: N
2x 3/2-way valve, single solenoid
• Normally open
• Pneumatic spring return
• Operating pressure > 3 bar
Position function 1-32: NS
2x 3/2-way valve, single solenoid
• Normally open
• Mechanical spring return
• Operating pressure –0.9 … +8 bar
Position function 1-32: K
2x 3/2-way valve, single solenoid
• Normally closed
• Pneumatic spring return
• Operating pressure > 3 bar
Position function 1-32: KS
2x 3/2-way valve, single solenoid
• Normally closed
• Mechanical spring return
• Operating pressure –0.9 … +8 bar
Internet: www.festo.com/catalog/...
The valve code (M, J, N, NS, K, KS, H,
HS, B, G, E, X, W, D, DS, I) is located on
the front of the valve beneath the
manual override.
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Valve function
Circuit symbol
Code
Description
Position function 1-32: H
2x 3/2-way valve, single solenoid
• Normally
– 1x closed
– 1x open
• Pneumatic spring return
• Operating pressure > 3 bar
2x 3/2-way valve, single solenoid
• Normally
– 1x closed
– 1x open
• Mechanical spring return
• Operating pressure –0.9 … +8 bar
5/3-way valve
• Mid-position pressurised1)
• Mechanical spring return
• Reversible
• Suitable for vacuum
Position function 1-32: HS
Position function 1-32: B
Position function 1-32: G
5/3-way valve
• Mid-position closed1)
• Mechanical spring return
• Reversible
• Suitable for vacuum
Position function 1-32: E
5/3-way valve
• Mid-position exhausted1)
• Mechanical spring return
• Reversible
• Suitable for vacuum
Position function 1-32: X
1x 3/2-way valve, single solenoid
• Normally closed
• External compressed air supply
• Pneumatic spring return
• Reversible
Compressed air (–0.9 … +10 bar) supplied at working line 4 can be switched
with both internal and external pilot air supply.
1x 3/2-way valve, single solenoid
• Normally open
• External compressed air supply
• Pneumatic spring return
• Reversible
Compressed air (–0.9 … +10 bar) supplied at working line 2 can be switched
with both internal and external pilot air supply.
2x 2/2-way valve
• Normally closed
• Pneumatic spring return
• Operating pressure > 3 bar
Position function 1-32: W
Position function 1-32: D
Position function 1-32: DS
2012/06 – Subject to change
2x 2/2-way valve
• Normally closed
• Mechanical spring return
• Operating pressure –0.9 … +8 bar
Internet: www.festo.com/catalog/...
11
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Valve function
Circuit symbol
1)
Code
Description
Position function 1-32: I
2x 2/2-way valve
• 1x normally closed
• 1x normally closed, reversible
• Pneumatic spring return
• Operating pressure > 3 bar
• Vacuum at port 3/5 only
If neither solenoid coil is energised, the valve moves to its mid-position by means of spring force.
If both coils are energised at the same time, the valve remains in the previously assumed switching position.
Note
A filter must be installed upstream of
valves operated in vacuum mode.
This prevents any foreign matter in
the intake air getting into the valve
(e.g. when operating a suction cup).
Blanking plate
Blanking plate (code L) without valve
function, for reserving valve positions
on a valve terminal.
Valves and blanking plates are
attached to the sub-base using two
screws.
The fixed restrictor can be used to
permanently set the flow rate when
venting in ducts 3 and 5.
The restrictor cuts a thread into the
retainer as it is screwed in. For that
reason, the retainer should also be
changed when a restrictor is
repeatedly replaced.
Fixed restrictor
Mounting:
• Press the retainer as far as it will go
into the exhaust openings on the
sub-base
• Screw the fixed restrictor into the
retainer
• Mount the valve on the sub-base
12
Internet: www.festo.com/catalog/...
The restrictor is available in
seven different nominal sizes
(0.3 … 1.7 mm). The individual sizes
are colour-coded to make them easy
to distinguish.
Fixed restrictors enable, for example,
the cylinder speed to be set to a
predefined limit in response to known
flow rate conditions.
They cannot be accessed during
operation and are therefore protected
against manipulation.
This is beneficial in the production of
standard machines since the required
speed can be determined once and
the installation simply duplicated for
further machines, saving time and
costs for repeated commissioning.
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Compressed air supply and venting
Supply module
Right-hand end plate
Venting (ducts 3 and 5) can
alternatively or additionally take place
via the right-hand end plate.
The ducts 3 and 5 are separate in the
terminal and are only joined together
in the supply module. The exhaust air
from the pilot air (duct 82/84) is
entirely separate from ducts 3 and 5.
The valve terminal MPA-L can be
supplied with compressed air at one
or more points via supply modules
and/or the right-hand end plate. The
generously sized pneumatic system
enables good performance from all
functional components, even with
large-scale expansions.
Venting (ducts 3 and 5) either takes
place via silencers or ports for ducted
exhaust air via the supply modules or
the right-hand end plate.
supply can be selected at the pilot air
selector on the end plate:
• Internal (from duct 1) or
• External (from duct 12/14)
Internal pilot air supply can be
selected if the supply pressure for
the terminal is between 3 and 8 bar.
In this case, the pilot air supply is
branched by means of an internal
connection from duct 1 in the
right-hand end plate.
Port 12/14 on the right-hand end
plate can be sealed using a blanking
plug.
If the supply pressure (at the
right-hand end plate) is less than
3 bar or greater than 8 bar, then the
valve terminal MPA-L must be
operated with an external pilot air
supply. The pilot air supply is then fed
via port 12/14 on the right-hand end
plate. When using several pressure
zones, the supply pressure in the
pressure zone with the right-hand end
plate is decisive.
There are two types of supply module
with venting:
• Exhaust air 3/5 via flat plate
silencer
• Exhaust air 3/5 ducted
Pilot air supply
The valve terminal type 34 MPA-L is
supplied with pilot air exclusively via
the right-hand end plate. The pilot air
Switching position for internal, marked ”Int”
Switching position for external, marked ”Ext”
Note
If a gradual pressure build-up in the
system using a soft-start valve is
chosen, an external pilot air supply
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
should be connected so that the
control pressure applied during
switch-on is already very high.
13
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Compressed air supply and pilot air supply
Pictorial representation
Code
Right-hand end plate, with supply ports
Right-hand end plate: D
Pilot air: –
Right-hand end plate: D
Pilot air: E
Right-hand end plate, without supply ports
Right-hand end plate: –
Pilot air: –
Notes
Internal pilot air supply
• Pilot air is branched internally from port 1 in the right-hand end plate
• Exhaust air 3/5 via right-hand end plate or supply module
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range 3 … 8 bar
External pilot air supply
• Pilot air supply (3 … 8 bar) is connected at the right-hand end plate at port 12/14
• Exhaust air 3/5 via right-hand end plate or supply module
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Internal pilot air supply
• Pilot air is branched internally from port 1 in the right-hand end plate
• Exhaust air 3/5 via supply module
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range 3 … 8 bar
Right-hand end plate: –
Pilot air: E
External pilot air supply
• Pilot air supply (3 … 8 bar) is connected at the right-hand end plate at port 12/14
• Exhaust air 3/5 via supply module
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Type of module block 1-40: U
Exhaust port: –
• Exhaust air 3/5 via flat plate silencer
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Type of module block 1-40: U
Exhaust port:
UD, UE, UF, UM, UN, UP or UG
• Exhaust air 3/5 via supply module
• Pilot exhaust air 82/84 via right-hand end plate
• For operating pressure in the range –0.9 … 10 bar (suitable for vacuum)
Supply module, flat plate silencer
Supply module, ducted exhaust air
14
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Supply module
Pictorial representation
Code
Type
Designation
Notes
Exhaust port:
UD, UE, UF, UM, UN, UP or UG
VMPAL-EG
Exhaust plate for ducted
exhaust air
Exhaust port: –
VMPAL-EU
Flat plate silencer
Type of module block 1-40: U
VMPAL-SP-0
Supply module with
electrical interlinking
module
Additional supply modules can be used
for larger terminals or to create
additional pressure zones.
Supply modules can be configured at
any point upstream or downstream of
the sub-bases.
Supply modules contain the following
ports:
• Compressed air supply (duct 1)
• Exhaust air (duct 3/5)
Depending on your order, the exhaust
ducts are either ducted or vented via
the flat plate silencer.
Pneumatic interface
The electrical power for the valves can
also be supplied via the serial bus of
the CPX terminal. The interlinking in
the pneumatic section of the valve
terminal remains the same as with a
multi-pin plug connection. The
pneumatic interface (left-hand end
plate) serves as an adapter between
the two current feeds.
Pneumatic interface
Pictorial representation
In the pneumatic interface, the serial
signals from the CPX terminal are
converted into parallel signals.
The number of addresses (solenoid
coils that can be connected) is set via
a selector (rotary switch) on the
pneumatic interface.
Code
Type
Electrical connection: CX VMPAL-…-EPL
2012/06 – Subject to change
Advantage:
Switching from a multi-pin plug
connection to fieldbus connection via
the CPX terminal and vice versa is
possible by swapping the left-hand
end plate; the pneumatic interlinking
is left as it is.
Notes
After converting or extending the valve terminal, the number of output
addresses occupied by the pneumatic components must be checked and if
applicable adjusted via the rotary switch on the pneumatic interface.
This is not necessary if a sufficiently large address space was previously
reserved for the extension (the standard setting on delivery provides for
32 valves).
The maximum number of addresses is specified via a selector switch in the
range 4 … 32 solenoid coils. This enables extensions to be pre-assigned in
a control program and called up by means of manual settings.
Internet: www.festo.com/catalog/...
15
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Creating pressure zones and separating exhaust air
MPA-L offers a number of options for
creating pressure zones if different
working pressures are required. Up
to nine pressure zones in total are
possible.
Pressure zones are created by
isolating the internal supply ducts
in a special sub-base. Each pressure
zone must have its own compressed
air supply.
Compressed air can be supplied
and vented via a supply module
and/or the right-hand end plate.
Creating pressure zones
Sub-bases with pressure zone separation
Pictorial examples
16
The position of the supply modules
and the sub-bases with pressure
zone separation can be freely
chosen with the valve terminal
MPA-L.
The sub-bases with pressure zone
separation are integrated in the
terminal ex-works as per your order.
They can be distinguished by their
coding, even when the valve
terminal is assembled. Duct
separation is always takes place to
the right of the sub-base.
Code
Notes
Duct separation to the
right of sub-base 1 - 40: –
• No duct separation
Duct separation to the
right of sub-base 1 - 40: T
• Duct 1 separated
• VMPAL-…-T1
Duct separation to the
right of sub-base 1 - 40:
TR
• Duct 3/5 separated
• VMPAL-…-T35
Duct separation to the
right of sub-base 1 - 40:
TS
• Ducts 1 and 3/5 separated
• VMPAL-…-T135
Coding
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Examples: Compressed air supply and pilot air supply
Internal pilot air supply, right-hand end plate without supply ports
The illustration opposite shows an
example of the configuration and
connection of the air supply with
internal pilot air supply.
The exhaust air (duct 3/5) is
discharged via supply modules.
The pilot exhaust air (duct 82/84) is
discharged via the right-hand end
plate.
Special sub-bases are used to create
pressure zones.
External pilot air supply, right-hand end plate without supply ports
The illustration opposite shows an
example of the configuration and
connection of the compressed air
supply with external pilot air supply.
Port 12/14 on the right-hand end
plate is equipped with a fitting for
this.
The exhaust air (duct 3/5) is
discharged via supply modules.
The pilot exhaust air (duct 82/84) is
discharged via the right-hand end
plate.
Special sub-bases are used to create
pressure zones.
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
17
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Sub-base
MPA-L is based on a modular system
consisting of sub-bases and valves.
The sub-bases are connected together
using tie rods and thus form the
support system for the valves.
They contain the connection ducts for
supplying compressed air to and
venting from the valve terminal as
well as the working lines for the
pneumatic drives for each valve.
Sub-base variants
Pictorial representation
Code
Type
Notes
–
VMPAL-AP-10
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
VMPAL-AP-10-QS
VMPAL-AP-10-…-T1
VMPAL-AP-10-T35
VMPAL-AP-10-T135
Electrical interlinking module
Pictorial representation
18
The sub-bases are joint together via
tie rods. The tie rod consists of
a threaded rod, threaded sleeve
and screw.
In principle, sub-bases have a
modular structure. If this modularity
is not required within a terminal, then
four individual sub-bases can be
combined with a 4-way electrical
interlinking module to save costs.
The threaded rod/sleeve combination
is selected as appropriate to the
number and width of the individual
plates or plate combination.
To add further blocks, simply loosen
the tie rod and adapt with extenders.
There are no restrictions on
extensions; a tie rod could be
constructed almost entirely from
extenders.
Working lines 2, 4 on the sub-base
Without electrical interlinking module
Working lines 2, 4 on the sub-base
With electrical interlinking module
Working lines 2, 4 on the sub-base
With/without electrical interlinking module
Duct separation in duct 1
Working lines 2, 4 on the sub-base
Without electrical interlinking module
Duct separation in ducts 3 and 5
Working lines 2, 4 on the sub-base
Without electrical interlinking module
Duct separation in ducts 1, 3 and 5
Working lines 2, 4 on the sub-base
With/without electrical interlinking module
No duct separation
4-valve unit, not suitable for pressure zone separation
Combination of
4 sub-bases: Z
VMPAL-AP-4x10
Code
Type
No. of solenoid coils
(valve positions)
Notes
Type of module
block 1-40: A
VMPA1-EVAP-10-2
2 (1), double solenoid
Type of module
block 1-40: C
VMPA1-EVAP-10-1
1 (1), single solenoid
Type of module
block 1-40: A
VMPA1-EVAP-10-2-4
8 (4), double solenoid
Each solenoid coil must be assigned to a specific pin
of the multi-pin plug in order for the valve to be
actuated. Regardless of whether blanking plates or
valves are used, valve positions occupy
• one coil/address (single solenoid valves)
• two coils/addresses (double solenoid valves)
Type of module
block 1-40: C
VMPA1-EVAP-10-1-4
4 (4), single solenoid
The electrical interlinking modules are colour-coded:
• Single solenoid – grey
• Double solenoid – black
Type of module
block 1-40: U
VMPA1-EVAP-20-SP
–
Electrical interlinking module for supply module
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Pneumatic components
Ports for supply and venting
Code
Right-hand end plate with supply ports 1, 3, 5
Right-hand end
plate: D
Port
QS fitting/cartridge fitting
1
Air/vacuum supply
Thread G¼
QS-G¼, straight,
for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, y†,
½†
3
Exhaust air
Thread G¼
5
Exhaust air
Thread G¼
12/14
Pilot air supply
Thread M7
82/84
Pilot exhaust air
Thread M7
1
Air/vacuum supply
Cartridge fitting
3/5
Exhaust air
Flat plate silencer –
QSM-M7, straight or angled,
for tubing O.D. 4 mm, 6 mm, ¼†
Supply module
Type of module
block 1-40: U
Right-hand end plate without supply ports
Right-hand end
plate: –
2012/06 – Subject to change
QSPKG20, straight,
for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, y†,
½†, adapter to thread G¼
Cartridge fitting
QSPKG20, straight,
for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, y†,
½†, adapter to thread G¼
12/14
Pilot air supply
–
–
82/84
Pilot exhaust air
–
–
1
Air/vacuum supply
–
–
3
Exhaust air
–
–
5
Exhaust air
–
–
12/14
Pilot air supply
Thread M7
82/84
Pilot exhaust air
Thread M7
QSM-M7, straight or angled,
for tubing O.D. 4 mm, 6 mm, ¼†
Internet: www.festo.com/catalog/...
19
-V- New
Valve terminals type 34 MPA-L
Key features – Assembly
Valve terminal assembly
Sturdy terminal assembly thanks to:
• Four through-holes for wall
mounting
• Additional mounting brackets
• H-rail mounting
Note
If the terminal is subject to strong
vibrations or shock loads, use
additional mounting brackets of the
type VMPAL-BD for wall mounting.
These should be attached to the valve
terminal every 13 cm (one mounting
bracket every 10 valve positions).
The MPA-L valve terminal is screwed
onto the mounting surface using four
M4 or M6 screws. The mounting holes
are on the multi-pin plug connection
and on the right-hand end plate.
Optional mounting brackets are also
available.
The MPA-L valve terminal is screwed
onto the mounting surface using four
M4 and two M6 screws or using six
M6 screws. The mounting holes are
on the left-hand and right-hand end
plate and on the pneumatic interface.
Optional mounting brackets are also
available.
The MPA-L valve terminal is
attached to the H-rail (see arrow A).
The terminal is then swivelled onto
the H-rail and secured in place with
the clamping component
(see arrow B).
The following MPA-L mounting kit is
required for H-rail mounting of the
valve terminal:
• With multi-pin plug connection:
CPX-CPA-BG-NRH
• With fieldbus connection
(CPX terminal):
VMPAF-FB-BG-NRH
This enables mounting of the valve
terminal on a H-rail to EN 60715.
Wall mounting – Multi-pin plug connection
Wall mounting – Fieldbus connection (CPX terminal)
H-rail mounting
A
B
Note
The mounting kits (see above) only
lock the valve terminal in horizontal
mounting position.
20
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Assembly
Tie rod
Design
1
2
3
4
1
2
3
4
Threaded rod
Tie rod extender
Sleeve
Screw
Mode of operation
The tie rod for MPA-L consists of four
parts:
• Threaded rod
• Tie rod extender
• Sleeve
• Screw
This enables valve terminals of any
length to be constructed.
The tie rod and valve terminal are
assembled in just four steps:
2012/06 – Subject to change
• Screw the threaded rods to the
left-hand end plate
• Screw the sleeves to the threaded
rods
• Push the sub-bases and supply
modules onto the rod/sleeve
combination
• Push on the right-hand end plate
and secure with screws that engage
into the sleeves
The tie rod enables subsequent
extension of the valve terminal. This is
done by loosening the tie rod screws
and disassembling the relevant
components. The additional sub-base
or supply module is inserted at the
required location. The previously
disassembled components are then
re-assembled.
Internet: www.festo.com/catalog/...
To compensate for the change in
length, the tie rod must be extended
by the increase in length. This is done
by screwing in extenders between the
threaded rod and sleeve. There are
suitable extenders for each sub-base,
combination of four sub-bases and
supply module.
21
-V- New
Valve terminals type 34 MPA-L
Key features – Assembly
Tie rod – Components and design
Tie rod (threaded rod)
The threaded rod is used to construct
a cost-optimised fixed-grid tie rod.
The threaded rod is required with
valve terminal lengths exceeding
42.45 mm, for example at least four
sub-bases (10.7 mm each) or two
sub-bases (10.7 mm each) and one
supply module (21.2 mm), since only
the combination of a threaded rod
and sleeve offers the optimum
compensation of tolerances (by
compressing the seals between the
sub-bases).
Tie rod extender
The valve terminal can be extended
almost infinitely using tie rod
extenders.
The tie rod extenders are inserted
between the threaded rod and sleeve
and are available in appropriate
lengths for sub-bases and supply
modules.
Sleeve
Screw
The primary purpose of the sleeve is
to compensate tolerances that occur,
for example, when the seals are
compressed between the sub-bases
during assembly.
The sleeves come in different lengths,
tailored to the use of a tie rod in
a fixed grid as well as generally for the
modular tie rods.
The entire valve terminal is clamped
via the tie rod using the screw.
Tolerances that occur, for example,
when the seals are compressed
between the sub-bases during
assembly are compensated by the
interaction of the screw and sleeve.
Tie rods can be constructed entirely
using tie rod extenders. The threaded
rod and sleeve are required to
compensate tolerances that occur, for
example, when the seals are
compressed between the sub-bases
during assembly.
The tie rod extenders are inserted
between the threaded rod and sleeve.
They are available in suitable lengths
for sub-bases and supply modules.
The fixed-grid tie rod minimises
assembly costs when assembling
previously defined valve terminals.
These valve terminals can be
extended at any time.
The threaded rod (and if applicable
also the sleeve) must be replaced if
the valve terminal length is reduced.
• Valve terminals with two valve
positions and without a supply
module are connected solely using
screws
• Valve terminals with three valve
positions and without a supply
module (or with one valve position
and one supply module) are
connected using a 10 mm tie rod
extender and screw
Individual modular tie rod
Fixed-grid tie rod with extension
Fixed-grid tie rod
Short valve terminal
Valve terminals with a small number
of valve positions are created by
means of the following combinations:
22
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Assembly
Ordering data – Fixed-grid tie rod
Reference length
Part No.
L = 10.65 x V + 21.15 x S
42.45 … 62.65
62.66 … 72.30
72.31 … 81.95
81.96 … 91.60
91.61 … 101.25
101.26 … 110.90
110.91 … 120.55
120.56 … 130.20
130.21 … 139.85
139.86 … 149.50
149.51 … 159.50
159.51 … 169.15
169.16 … 178.80
178.81 … 188.45
188.46 … 198.10
198.11 … 207.75
207.76 … 217.40
217.41 … 227.05
227.06 … 236.70
236.71 … 246.35
246.36 … 256.00
256.01 … 266.00
266.01 … 275.65
275.66 … 285.30
285.31 … 294.95
294.96 … 304.60
304.61 … 314.25
314.26 … 323.90
323.91 … 333.55
333.56 … 343.20
343.21 … 352.85
352.86 … 362.50
362.51 … 372.50
372.51 … 382.50
382.51 … 392.50
392.51 … 402.50
402.51 … 412.50
412.51 … 422.50
422.51 … 432.50
432.51 … 442.50
442.51 … 452.50
452.51 … 462.50
462.51 … 472.50
472.51 … 482.50
482.51 … 492.50
492.51 … 502.50
502.51 … 512.50
512.51 … 522.50
Tie rod
561116
561116
561116
561116
561117
561117
561117
561117
561118
561118
561118
561118
561119
561119
561119
561119
561120
561120
561120
561120
561121
561121
561121
561121
561122
561122
561122
561122
561123
561123
561123
561123
561124
561124
561124
561124
561125
561125
561125
561125
561126
561126
561126
561126
561127
561127
561127
561127
V
S
Type
Part No.
Type
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-5
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-45
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-85
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-125
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-165
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-205
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-245
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-285
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-325
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-365
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-405
VMPAL-ZAS-445
VMPAL-ZAS-445
VMPAL-ZAS-445
VMPAL-ZAS-445
Sleeve
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
561135
561136
561137
561138
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
Number of valve positions
Number of supply modules
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
23
-V- New
Valve terminals type 34 MPA-L
Key features – Display and operation
Display and operation
Signal status display
Manual override
Each solenoid coil is allocated an LED
that indicates its signal status.
• Indicator 12 shows the switching
status of the coil for duct 2
• Indicator 14 shows the switching
status of the coil for duct 4
The manual override (MO) enables
the valve to be actuated when not
electrically activated or energised.
The valve is activated by pushing the
manual override.
Alternatives:
• A cover (code: N or as accessory)
enables the manual override to be
actuated by pressing it using an
appropriate tool.
• A cover (code V) can be fitted over
the manual override to prevent it
from being accidentally actuated.
Pneumatic connection and control elements
2
1
3
4
5
6
5
Manual override (MO)
MO with automatic return (non-detenting)
1
24
2
1 Flat plate silencer, duct 3/5
2 Manual override
(for each pilot solenoid coil,
non-detenting or
non-detenting/detenting)
3 Ducted exhaust air, duct 3/5
4 Ports 12/14 for external pilot air
supply and 82/84 for pilot
exhaust air in the right-hand end
plate (depending on version also
ducts 1, 3 and 5)
5 Supply port, duct 1
6 Working lines, ducts 2 and 4,
for each valve position
Note
A valve actuated manually
(by means of the manual override)
cannot be reset electrically.
Conversely, an electrically actuated
valve cannot be reset using the
manual override.
MO set via turning (detenting)
1 Press in the stem of the MO with
a pointed object or screwdriver.
Pilot valve switches and actuates
the main valve.
2 Remove the pointed object or
screwdriver.
Spring force pushes the stem of
the MO back.
Pilot valve returns to its initial
position and so too the single
solenoid main valve (not with
double solenoid valve code J).
Internet: www.festo.com/catalog/...
1
2
1 Press in the stem of the MO with
a pointed object or screwdriver
until the valve switches and then
turn the stem clockwise by 90°
until the stop is reached.
Valve remains switched.
2 Turn the stem anti-clockwise by
90° until the stop is reached and
then remove the pointed object
or screwdriver. Spring force
pushes the stem of the MO back.
Valve returns to its initial
position (not with double
solenoid valve code J).
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Electrical components
Inscription system
Inscription area
approx. 20 x 45 mm
A holder VMPAL-ST-AP-10
(Part No. 561109) with inscription
labels (Part No. 18576, IBS-6x10) can
be mounted on each sub-base for
labelling the valves.
Large inscription labels can be
attached to the pneumatic interface as
an alternative or in addition to the
smaller labels.
Each solenoid coil is protected with
a spark arresting protective circuit as
well as against polarity reversal.
All valve types are additionally
equipped with integrated current
reduction.
MPA-L valves are supplied with
operating voltage in the range
21.6 … 26.4 V (24 V +/–10%).
IBS-6x10
VMPAL-ST-AP-10
Electrical power as a result of current reduction
Power management
Electrical multi-pin plug connection
The following multi-pin plug
connections are offered for the valve
terminal MPA-L:
• Sub-D (9-pin), 8 addresses
• Sub-D (25-pin), 24 addresses
• Sub-D (44-pin), 32 addresses
• Flat cable connection (40-pin),
32 addresses
• Terminal strip connection (33-pin),
32 addresses
Pins 1 … 32 are used for addresses
0 … 31 in order.
If fewer addresses are used for the
valve terminal, the remaining pins
(up to 32) are left free.
The valves are switched by means of
positive or negative logic (PNP or
NPN). Mixed operation is not
permitted.
Each pin on the multi-pin plug can
actuate exactly one solenoid coil. If
the maximum configurable number
of valve positions is 32, this means
that 32 valves, each with a single
solenoid coil, can be addressed.
Note
If a single solenoid valve is
assembled on a double solenoid
valve position, the second address
is also occupied and cannot be
used.
Guidelines on addressing for valves/solenoid coils
• The maximum possible number of
addresses is 32.
• The numbering of the addresses
goes from left to right in ascending
consecutive order. The following
applies to the individual valve
positions: address x for coil 14 and
address x+1 for coil 12.
• If single solenoid valves are
mounted on sub-bases for double
solenoid valves, the address of
coil 12 and the assigned pin will
remain unused.
• Each sub-base/electrical
interlinking module occupies a
defined number of addresses/pins:
– For single solenoid valve: 1
– For double solenoid valve: 2
This means:
• The valves and outputs are supplied
via the system supply for the CPX
terminal
• The valves can optionally be
actuated or switched off separately
from the outputs
– For combination of four
sub-bases for single solenoid
valves: 4
– For combination of four
sub-bases for double solenoid
valves: 8
Fieldbus connection CPX
All functions and features of the
electrical peripherals CPX are
permitted in connection with the CPX
interface.
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
Note
Further information can be found at:
Internet: cpx
25
-V- New
Valve terminals type 34 MPA-L
Key features – Electrical components
Pin allocation – Sub-D plug, 9-pin
1)
Pin Address/coil
Pin Address/coil
1
0
6
5
2
1
7
6
3
2
8
7
4
3
9
0 V1)
5
4
0
WH
14
13
BN YE
2
1
GN
15
14
GY WH
3
2
YE
16
15
BN GY
4
3
GY
17
16
WH PK
5
4
PK
18
17
BN PK
6
5
BU
19
18
BU WH
7
6
RD
20
19
BN BU
8
7
VT
21
20
RD WH
9
8
GY PK
22
21
BN RD
10
9
RD BU
23
22
BK WH
11
10
GN WH
24
23
BN
12
11
BN GN
25
0 V1)
BK
13
12
YE WH
Note
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
To IEC 757
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
26
Pin Address/co Connecting cable
il
wire colour2)
1
Pin allocation – Sub-D plug, 44-pin, connecting cable VMPAL-KM
Pin Address/co Connecting cable
il
wire colour2)
1)
2)
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Pin allocation – Sub-D plug, 25-pin, connecting cable VMPAL-KM
Pin Address/co Connecting cable
il
wire colour2)
1)
2)
Note
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
WH
GN
YE
GY
PK
BU
RD
VT
GY PK
RD BU
GN WH
BN GN
YE WH
BN YE
GY WH
BN GY
WH PK
Pin Address/co Connecting cable
il
wire colour2)
Pin Address/co Connecting cable
il
wire colour2)
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
n.c.
n.c.
BN PK
BU WH
BN BU
RD WH
BN RD
BK WH
BN
BK BN
GN GY
YE GY
GN PK
YE PK
GN BU
YE BU
RN GN
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
0 V1)
0 V1)
0 V1)
0 V1)
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
RD YE
BK GN
BK YE
BK
Note
The drawing shows the view onto the
pins of the Sub-D plug.
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
To IEC 757
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Electrical components
Ordering data
Designation
Code
Description
Connection Cable length
Connecting cable for multi-pin plug connection with Sub-D plug socket
Connecting cable: CA
Cable outlet to front
25-pin
(only with electrical connection
Connecting cable: CB
code: MS6)
Connecting cable: CC
Connecting cable: –
Connecting cable: CQ
Cable outlet to front
25-pin
(only with electrical connection
Connecting cable: CR
code: MS6)
Connecting cable: CS
Suitable for use with energy chains
Connecting cable: –
Connecting cable: CJ
Connecting cable: CK
Connecting cable: CL
Connecting cable: –
Connecting cable: CD
Connecting cable: CE
Connecting cable: CH
Connecting cable: –
Connecting cable: CT
Connecting cable: CU
Connecting cable: CV
Connecting cable: –
Connecting cable: CM
Connecting cable: CN
Connecting cable: CP
Connecting cable: –
Cable outlet to front
(only with electrical connection
code: MS8)
44-pin
Cable outlet to side
(only with electrical connection
code: MS6)
25-pin
Cable outlet to side
25-pin
(only with electrical connection
code: MS6)
Suitable for use with energy chains
Cable outlet to side
(only with electrical connection
code: MS8)
44-pin
Cover for multi-pin plug connection without connecting cable with Sub-D plug socket
Connecting cable: EZ
Cable outlet to side or front
25-pin
(only with electrical connection
code: MS6)
Connecting cable: EY
Cable outlet to side or front
44-pin
(only with electrical connection
code: MS8)
2012/06 – Subject to change
Part No.
Type
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
2.5 m
5m
10 m
Any
560416
560417
560418
562389
560410
560411
560412
562391
560422
560423
560424
562390
560419
560420
560421
562392
560413
560414
560415
562394
560425
560426
560427
562393
VMPAL-KM-V-SD25-IP67-2,5
VMPAL-KM-V-SD25-IP67-5
VMPAL-KM-V-SD25-IP67-10
VMPAL-KM-V-SD25-IP67-X
VMPAL-KMSK-V-SD25-IP67-2,5
VMPAL-KMSK-V-SD25-IP67-5
VMPAL-KMSK-V-SD25-IP67-10
VMPAL-KMSK-V-SD25-IP67-X
VMPAL-KM-V-SD44-IP67-2,5
VMPAL-KM-V-SD44-IP67-5
VMPAL-KM-V-SD44-IP67-10
VMPAL-KM-V-SD44-IP67-X
VMPAL-KM-S-SD25-IP67-2,5
VMPAL-KM-S-SD25-IP67-5
VMPAL-KM-S-SD25-IP67-10
VMPAL-KM-S-SD25-IP67-X
VMPAL-KMSK-S-SD25-IP67-2,5
VMPAL-KMSK-S-SD25-IP67-5
VMPAL-KMSK-S-SD25-IP67-10
VMPAL-KMSK-S-SD25-IP67-X
VMPAL-KM-S-SD44-IP67-2,5
VMPAL-KM-S-SD44-IP67-5
VMPAL-KM-S-SD44-IP67-10
VMPAL-KM-S-SD44-IP67-X
–
560428
VMPAL-KM-SD25-IP67-0
–
560429
VMPAL-KM-SD44-IP67-0
Internet: www.festo.com/catalog/...
27
-V- New
Valve terminals type 34 MPA-L
Key features – Electrical components
Pin allocation – Flat cable, 40-pin
1)
Pin Address/coil
Pin Address/coil
Pin Address/coil
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
28
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
0 V1)
Note
The drawing shows the view onto the
pins of the flat cable plug.
The flat cable connection is
established using plug connectors, in
accordance with
DIN EN 60603-13:1998-09
(NECU-FCG40-K).
Internet: necu
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Pin allocation – Terminal strip, 33-pin
Pin Address/coil
1)
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0 V1)
0 V1)
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Pin Address/coil
Pin Address/coil
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
0 V1)
Note
The drawing shows the view onto the
pins of the terminal strip.
Cables with the following
specifications can be connected:
• Cable cross section
0.08 … 0.5 mm2
• Insulation 5 … 6 mm
0 V for positive switching control signals; connect 24 V for negative switching control signals; mixed operation is not permitted.
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Key features – Electrical components
Instructions for use
Equipment
Operate system equipment with
unlubricated compressed air if
possible. Festo valves and cylinders
are designed so that, if used as
intended, they will not require
additional lubrication and will still
achieve a long service life.
The quality of compressed air
downstream of the compressor must
correspond to that of unlubricated
compressed air. If possible, do not
operate all of your system equipment
with lubricated compressed air. The
lubricators should, where possible,
always be installed directly upstream
of the actuator used.
2012/06 – Subject to change
Bio-oils
Unsuitable additional oil and too high
an oil content in the compressed air
reduce the service life of the valve
terminal.
Use Festo special oil OFSW-32 or the
alternatives listed in the Festo
catalogue (as specified in DIN 51524
HLP32; basic oil viscosity 32 CST
at 40 °C).
When using bio-oils (oils which are
based on synthetic or native ester,
e.g. rapeseed oil methyl ester), the
maximum residual oil content of
0.1 mg/m3 must not be exceeded
(see ISO 8573-1 Class 2).
Internet: www.festo.com/catalog/...
Mineral oils
When using mineral oils (e.g. HLP oils
to DIN 51524, parts 1 to 3) or similar
oils based on poly-alpha-olefins
(PAO), the maximum residual oil
content of 5 mg/m3 must not be
exceeded (see ISO 8573-1 Class 4).
A higher residual oil content
irrespective of the compressor oil
cannot be permitted, as the basic
lubricant would be flushed out over
time.
29
-V- New
Valve terminals type 34 MPA-L
Technical data
Flow rate
Up to 360 l/min
Width
10 mm
Voltage
24 V DC
General technical data
Design
Lubrication
Type of mounting
Mounting position
Manual override
Width
[mm]
Electromagnetically actuated piston spool valve
Lubricated for life, PWIS-free (free of paint-wetting impairment substances)
Wall mounting
On H-rail to EN 60715
Any (wall mounting)
Horizontal only (H-rail)
Non-detenting, detenting, blocked
10
Pneumatic connections, right-hand end plate
Supply
1
Thread G¼ (QS-G¼, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, ņ, ½†)
Exhaust port
3
Thread G¼ (QS-G¼, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, ņ, ½†)
5
Thread G¼ (QS-G¼, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, ņ, ½†)
Pilot air supply
12/14
Thread M7 (QSM-M7, straight or angled, for tubing O.D. 4 mm, 6 mm, ¼†)
Pilot exhaust air
82/84
Thread M7 (QSM-M7, straight or angled, for tubing O.D. 4 mm, 6 mm, ¼†)
Pneumatic connections, supply module
Supply
1
Exhaust port
3/5
Pneumatic connections, sub-base
Working lines
2
4
30
Cartridge fitting 20 mm (QSPKG20, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, ņ, ½†,
adapter for thread G¼), flat plate silencer
Cartridge fitting 20 mm (QSPKG20, straight, for tubing O.D. 8 mm, 10 mm, 12 mm, Ć, ņ, ½†,
adapter for thread G¼), flat plate silencer
Cartridge fitting 10 mm (QSPKG10, straight or angled, for tubing O.D. 4 mm, 6 mm, Á†, †, Æ, ¼†,
adapter for thread M7)
Cartridge fitting 10 mm (QSPKG10, straight or angled, for tubing O.D. 4 mm, 6 mm, Á†, †, Æ, ¼†,
adapter for thread M7)
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Technical data
Operating and environmental conditions
Code for position function 1-32
M
Operating medium
Note on operating/pilot medium
Operating pressure
[bar]
Operating pressure for valve [bar]
terminal with internal
pilot air supply
Pilot pressure
[bar]
Ambient temperature
[°C]
Temperature of medium
[°C]
Storage temperature1)
[°C]
1)
J
B
G
E
X
W
N
K
H
D
I
NS
KS
HS
DS
Compressed air in accordance with ISO 8573-1:2010 [7:4:4] 29
Operation with lubricated medium possible (in which case lubricated operation will always be required)
–0.9 … +10
3 … 10
–0.9 … +8
3…8
3…8
–5 … +50
–5 … +50
–20 … +40
Long-term storage
p2 [bar]
Pilot pressure p2 as a function of working pressure p1 with external pilot air supply
For valves with code M, J, B, G, E, X, W
p1 [bar]
1 Operating range for valves with
external pilot air supply
p2 [bar]
For valves with code N, K, H, D, I
p1 [bar]
2012/06 – Subject to change
1 Operating range for valves with
external pilot air supply
Internet: www.festo.com/catalog/...
31
-V- New
Valve terminals type 34 MPA-L
Technical data
Pilot pressure p2 as a function of working pressure p1 for valves with mechanical spring return
For valves with code NS, KS, HS, DS
Nominal flow rate [l/min]
Valve function
5/2-way valve, single solenoid
1x 3/2-way valve
5/2-way valve, double solenoid
5/3-way valve, mid-position pressurised
5/3-way valve, mid-position closed
2x 2/2-way valve
5/3-way valve, mid-position exhausted
2x 3/2-way valve, normally closed
2x 3/2-way valve, normally open
2x 3/2-way valve, 1x normally open, 1x normally closed
2x 2/2-way valve
1x 3/2-way valve
2x 3/2-way valve, normally closed, mechanical spring return
2x 3/2-way valve, normally open, mechanical spring return
2x 3/2-way valve, 1x normally open and 1x normally closed, mechanical spring
return
2x 2/2-way valve, mechanical spring return
1)
With fitting QS-6
From port
1 to 2, or 1 to 4
From port
2 to 3, or 4 to 5
M
X
J
B
G
I
E
K
N
H
D
W
KS
NS
HS
360
255
360
300 (220)1)
320
260
240
230
300
300
230
255 (2 to 4)
230
300
300
360
295
360
270
350
260
240 (200)1)
310
300
300
–
295 (4 to 5)
310
300
300
DS
230
–
Value for mid-position
Valve switching times [ms]
Code for position function 1-32
Switching times
32
Code
Position function
1-32
On
Off
Changeo
ver
M
J
N
K
H
B
G
E
X
W
D
I
NS
KS
HS
DS
10
20
–
10
–
15
10
20
–
10
20
–
10
20
–
10
35
–
10
35
–
10
35
–
10
20
–
10
20
–
10
20
–
10
20
–
14
16
–
14
16
–
14
16
–
14
16
–
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Technical data
Electrical data
Nominal voltage
Operating voltage range
Protection class to EN 60529
[V DC]
[V DC]
24
21.6 … 26.4
IP65 (for all types of signal transmission in assembled state)
Current consumption per solenoid coil at nominal voltage
Nominal pick-up current
[mA]
50
Nominal current with current
[mA]
10
reduction
Time until current reduction
[ms]
20
Electrical data – MPA-L with electrical interface for CPX terminal
Intrinsic current consumption of valve terminal (internal electronics, without valves)
At 24 V UEL/SEN 1)
[mA]
Typically 13
At 24 V Uval 2)
[mA]
Typically 35
Diagnostic message
Undervoltage UOFF 3)
1)
2)
3)
[V]
17.7 … 17.8
Power supply for electronics and sensors
Load voltage supply for valves
Load voltage outside of function range
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
33
-V- New
Valve terminals type 34 MPA-L
Technical data
Materials
Sub-base
Valve
Supply module
End plate
Seals
Exhaust plate
Flat plate silencer
Electrical interlinking module
PA
Die-cast aluminium
PPA
Die-cast aluminium, PA, PBT
NBR
PA
PE
PBT, PA, copper alloy
Product weight
Approx. weight [g]
CPX module (complete)
Left-hand end plate, multi-pin plug,
Sub-D, 44-pin
Black sub-base
(with seal, fibre-optic cable)
Electrical interlinking module for one
sub-base
Electrical interlinking module for
combination of four sub-bases
Supply module with seal, electrical
interlinking module
Per valve VMPA1-M1H-M, X, W
Per valve VMPA1-M1H-J, N, K, H, B, G,
E, D
Per vacant position L
Right-hand end plate
without supply ports
Right-hand end plate
with supply ports
Screw for tie rod
Threaded rods for tie rod,
5/45/85/205/285 mm
Sleeve for tie rod, 36/46/56/66 mm
Plate for ducted exhaust air/flat plate
silencer
QSM-M7-4-I
QSM-M7-6-I
QS-G¼-8-I
QS-G¼-10-I
Approx. 210
130
QSPKG10-3
QSPKG10-4
QSPKG10-6
QSPKG20-8
QSPKG20-10
QSPKG20-12
1
1
2
6
9
12
34
21
9
29
51
49
56
24
105
160
3
2/11/20/47/65
6/8/9/11
36/40
4
5
22
23
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Technical data
Download CAD Data www.festo.com/us/cad
Dimensions
Valve terminal with multi-pin plug connection
1 Solenoid valve
2 Manual override
3 Supply module
Type
4 Working lines
5 H-rail
L11)
L21)
L3
6 H-rail mounting
7 Mounting holes
8 Earthing screw
9 Multi-pin plug connection
L4
L5
L6
L7
L8
L9
L10
L11
L12
21.2
24.9
10.7
8.5
6.8
6.5
5.6
1.5
1
,
MPA-L
89.10 + n x 10.70
Type
B1
B2
MPA-L
107.3
66.3
n x 10.70
B3
64.3
B4
B5
B6
B7
B8
H1
33.5
23.5
18.9
7.5
7.5
69.6
,
1)
65
H2
H3
H4
H5
H6
D1
D2
28.5
27.9
8.5
10.9
6.6
4.4
,
36.4
n = number of sub-bases/valve positions
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
35
-V- New
Valve terminals type 34 MPA-L
Technical data
Download CAD Data www.festo.com/us/cad
Dimensions
Valve terminal with fieldbus connection
1 Solenoid valve
2 Manual override
3 Supply module
4 Working lines
5 H-rail
6 H-rail mounting
Type
L11)
L21)
MPA-L
170.9 + n x 10.70
n x 10.70
Type
B1
B2
MPA-L
124
107.3 66.3
L3
L4
7 Mounting holes
8 Pneumatic interface for CPX
terminal
9 CPX module
aJ Earthing screw
L5
L6
L7
L8
L9
L10
L11
L12
L13
L14
D1
D2
D3
40.1
21.2
28.8
24
30
10.7
8.5
6.8
5.6
6.5
6.6
4.4
7
,
B3
142.1 50
B4
B5
B6
B7
B8
B9
B10
B11
H1
H2
65
33.5
23.5
15
13
7.5
5.3
5.5
69.6
65.7
,
1)
36
H3
H4
H5
H6
H7
39.8
28.5
25.8
8.5
,
52
n = number of sub-bases/valve positions
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Technical data
Download CAD Data www.festo.com/us/cad
Dimensions – Cover for multi-pin plug connection
Cable outlet to front
Type
L1
Cable outlet to side
L2
H1
H2
B1
B2
B3
14
26
34.5
34.5
–
27
–
29
,
Cable outlet to front
Cable outlet to side
2012/06 – Subject to change
108.3
114.5
27
–
44.4
32.4
Internet: www.festo.com/catalog/...
37
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Valve function
Part No.
Type
533342
533343
533348
556839
VMPA1-M1H-M-PI
VMPA1-M1H-J-PI
VMPA1-M1H-N-PI
VMPA1-M1H-NS-PI
540050
VMPA1-M1H-W-PI
533347
556838
VMPA1-M1H-K-PI
VMPA1-M1H-KS-PI
533349
VMPA1-M1H-H-PI
556840
VMPA1-M1H-HS-PI
533344
533345
533346
534415
VMPA1-M1H-B-PI
VMPA1-M1H-G-PI
VMPA1-M1H-E-PI
VMPA1-M1H-X-PI
533350
556841
VMPA1-M1H-D-PI
VMPA1-M1H-DS-PI
543605
VMPA1-M1H-I-PI
Sub-base valve
Position function 1-32: M
Position function 1-32: J
Position function 1-32: N
Position function 1-32: NS
5/2-way valve, single solenoid
5/2-way valve, double solenoid
2x 3/2-way valve, normally open
2x 3/2-way valve, normally open,
mechanical spring return
Position function 1-32: W 1x 3/2-way valve, normally open,
external compressed air supply
Position function 1-32: K 2x 3/2-way valve, normally closed
Position function 1-32: KS 2x 3/2-way valve, normally closed,
mechanical spring return
Position function 1-32: H 2x 3/2-way valve,
1x normally open, 1x normally closed
Position function 1-32: HS 2x 3/2-way valve,
1x normally open, 1x normally closed,
mechanical spring return
Position function 1-32: B 5/3-way valve, mid-position pressurised
Position function 1-32: G 5/3-way valve, mid-position closed
Position function 1-32: E
5/3-way valve, mid-position exhausted
Position function 1-32: X
1x 3/2-way valve, normally closed,
external compressed air supply
Position function 1-32: D 2x 2/2-way valve, normally closed
Position function 1-32: DS 2x 2/2-way valve, normally closed,
mechanical spring return
Position function 1-32: I
2x 2/2-way valve,
1x normally closed
1x normally closed, reversible
Sub-base
Duct separation to the
right of sub-base 1-40: –
Duct separation to the
right of sub-base 1-40: T
Duct separation to the
right of sub-base 1-40: TR
Duct separation to the
right of sub-base 1-40: TS
–
Single,
without electrical
interlinking module,
without cartridge fitting
Single,
with electrical
interlinking module,
with cartridge fitting,
no duct separation
Single,
with electrical
interlinking module,
with cartridge fitting,
duct 1 separated
38
No duct separation
–
554311
VMPAL-AP-10
Duct 1 separated
–
554312
VMPAL-AP-10-T1
Ducts 3, 5 separated
–
554313
VMPAL-AP-10-T35
Ducts 1 and 3,
5 separated
Single solenoid
(for 1 solenoid coil)
–
554315
VMPAL-AP-10-T135
6 mm
4 mm
¼†
†
6 mm
4 mm
¼†
†
6 mm
560987
560994
560999
561005
560993
560988
561000
561006
561011
VMPAL-AP-10-QS6-1
VMPAL-AP-10-QS4-1
VMPAL-AP-10-QS¼†-1
VMPAL-AP-10-QS†-1
VMPAL-AP-10-QS6-2
VMPAL-AP-10-QS4-2
VMPAL-AP-10-QS¼†-2
VMPAL-AP-10-QS†-2
VMPAL-AP-10-QS6-1-T1
Double solenoid
(for 2 solenoid coils)
Single solenoid
(for 1 solenoid coil)
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
–
Single,
with electrical
interlinking module,
with cartridge fitting,
duct 1 separated
Single solenoid
(for 1 solenoid coil)
4 mm
¼†
†
6 mm
4 mm
¼†
†
561017
561023
561029
561012
561018
561024
561030
VMPAL-AP-10-QS4-1-T1
VMPAL-AP-10-QS¼†-1-T1
VMPAL-AP-10-QS†-1-T1
VMPAL-AP-10-QS6-2-T1
VMPAL-AP-10-QS4-2-T1
VMPAL-AP-10-QS¼†-2-T1
VMPAL-AP-10-QS†-2-T1
Without electrical
interlinking module,
without cartridge fitting
–
–
560981
VMPAL-AP-4x10
With electrical
interlinking module,
with cartridge fitting,
no duct separation,
single solenoid (for 1
solenoid coil)
Tubing O.D.
6 mm
561083
VMPAL-AP-4x10QS6-1
4 mm
561089
VMPAL-AP-4x10QS4-1
¼†
561095
VMPAL-AP-4x10QS¼†-1
†
561101
VMPAL-AP-4x10QS†-1
With electrical
interlinking module,
with cartridge fitting,
no duct separation,
double solenoid (for 2
solenoid coils)
Tubing O.D.
6 mm
561084
VMPAL-AP-4x10QS6-2
4 mm
561090
VMPAL-AP-4x10QS4-2
¼†
561096
VMPAL-AP-4x10QS¼†-2
†
561102
VMPAL-AP-4x10QS†-2
5 mm
45 mm
85 mm
125 mm
165 mm
205 mm
245 mm
285 mm
325 mm
365 mm
405 mm
445 mm
36 mm
46 mm
56 mm
66 mm
561116
561117
561118
561119
561120
561121
561122
561123
561124
561125
561126
561127
561135
561136
561137
561138
561139
561141
570779
571924
VMPAL-ZAS-5
VMPAL-ZAS-45
VMPAL-ZAS-85
VMPAL-ZAS-125
VMPAL-ZAS-165
VMPAL-ZAS-205
VMPAL-ZAS-245
VMPAL-ZAS-285
VMPAL-ZAS-325
VMPAL-ZAS-365
VMPAL-ZAS-405
VMPAL-ZAS-445
VMPAL-ZAH-36
VMPAL-ZAH-46
VMPAL-ZAH-56
VMPAL-ZAH-66
VMPAL-ZAE-10
VMPAL-ZAE-20
VMPAL-ZAE-10-4
VMPAL-M-4x30
561142
VMPAL-MS-4x10
Sub-base
Combination of four sub-bases
Combination manifold
block: Z
–
Double solenoid
(for 2 solenoid coils)
Tie rod
Tie rod: –
Threaded rod for tie rod, width across flats 5 mm
The threaded rod/sleeve combination is selected
based on the number and width of the individual
sub-base
–
Sleeve, internal hex 4 mm
–
Tie rod extender for
For one sub-base
subsequently extending For one supply module
the valve terminal
For four sub-bases
Screw M4x30 mm with internal hex 2.5 mm,
3 pieces
for tie rod
–
Screw
–
2012/06 – Subject to change
Screw M4x10 mm and nut with internal hex
2.5 mm, for linking four sub-bases
10 pieces
Internet: www.festo.com/catalog/...
39
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
–
Mounting bracket
Wall brackets should be mounted max. every
13 cm on the valve terminal.
560949
VMPAL-BD
Mounting accessories: H
MPA-L with multi-pin plug connection
526032
CPX-CPA-BG-NRH
Mounting accessories: H
MPA-L with fieldbus connection
560798
VMPAF-FB-BG-NRH
For one sub-base
Grey – single solenoid
(for 1 solenoid coil)
Black – double solenoid
(for 2 solenoid coils)
Grey – single solenoid
(for 4 solenoid coils, 4 valve positions)
Black – double solenoid
(for 8 solenoid coils, 4 valve positions)
560961
VMPAL-EVAP-10-1
560962
VMPAL-EVAP-10-2
560967
VMPAL-EVAP-10-1-4
560968
VMPAL-EVAP-10-2-4
Black
571011
VMPAL-EVAP-20-SP
Mounting
10 pieces
H-rail mounting
Electrical interlinking module
Type of module block
1-40: C
Type of module block
1-40: A
Type of module block
1-40: C
Type of module block
1-40: A
For one sub-base
For combination of
four sub-bases
For combination of
four sub-bases
Type of module block
1-40: U
For supply module
(signals are passed
through)
–
For releasing the electrical interlinking module from the
sub-base
572017
VMPAL-LW
–
Fixed restrictor, two of each size,
two retainers and assembly tool
572543
VMPA1-FT-NW0.3-1.7
Fixed restrictor – Hollow bolt, for restricting the exhaust air in ducts 3 and 5, 10 pieces
–
qnN 3.5 … 5.5 l/min, orange, nominal size 0.3 mm
qnN 9 … 12 l/min, green, nominal size 0.5 mm
qnN 18 … 22 l/min, purple, nominal size 0.7 mm
qnN 36 … 41 l/min, black, nominal size 1.0 mm
qnN 52 … 58 l/min, red, nominal size 1.2 mm
qnN 81 … 89 l/min, blue, nominal size 1.5 mm
qnN 105 … 115 l/min, clear, nominal size 1.7 mm
572544
572545
572546
572547
572548
572549
572550
VMPA1-FT-NW0.3-10
VMPA1-FT-NW0.5-10
VMPA1-FT-NW0.7-10
VMPA1-FT-NW1.0-10
VMPA1-FT-NW1.2-10
VMPA1-FT-NW1.5-10
VMPA1-FT-NW1.7-10
Retainer for fixed restrictor
–
572542
VMPA1-FTI-10
Releasing tool
Restrictor set
40
Retainer for exhaust opening in the sub-base
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
Type of module block
1-40: U
With electrical interlinking module, without cartridge fitting
560950
VMPAL-SP-0
Type of module block
1-40: U
With electrical interlinking module,
with cartridge fitting for tubing O.D.
8 mm
10 mm
12 mm
Ć
y†
½†
Without electrical interlinking module, without cartridge fitting
573645
560951
560952
573646
560953
560954
570774
VMPAL-SP-QS8
VMPAL-SP-QS10
VMPAL-SP-QS12
VMPAL-SP-QSĆ
VMPAL-SP-QSy†
VMPAL-SP-QS½†
VMPAL-SP
Exhaust port:
UD, UE, UF, UM, UN, UP or
UG
Exhaust plate for ducted exhaust air
560956
VMPAL-EG
Exhaust port:
UE
Exhaust port:
UN
Exhaust port:
–
Exhaust plate for ducted exhaust air, with cartridge fitting for
tubing O.D. 10 mm
Exhaust plate for ducted exhaust air, with cartridge fitting for
tubing O.D. y†
Flat plate silencer
560957
VMPAL-EG-QS10
560959
VMPAL-EG-QSy†
560955
VMPAL-EU
Supply module
Type of module block
1-40: U
Plate
2012/06 – Subject to change
Internet: www.festo.com/catalog/...
41
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
Position function 1-32: L
Blanking plate for vacant valve position1)
533351
VMPA1-RP
Manual override: N
Cover for manual override, non-detenting (10 pieces)
540897
VMPA-HBT-B
Manual override: V
Cover for manual override, covered (10 pieces)
540898
VMPA-HBV-B
Right-hand end plate: –
Low,
with ports 12/14, 82/84,
with pilot air selector for choosing the pilot air supply
(internal or external)
560945
VMPAL-EPR
Right-hand end plate: D
High,
with ports 1, 3, 5, 12/14, 82/84,
with pilot air selector for choosing the pilot air supply
(internal or external), reversible operation possible
560947
VMPAL-EPR-SP
570777
VMPAL-EPL-SD9-IP40
560940
VMPAL-EPL-SD25-IP40
560941
VMPAL-EPL-SD44-IP40
560942
VMPAL-EPL-FL40-IP40
560943
VMPAL-EPL-KL33-IP40
560938
VMPAL-EPL-SD25
560939
VMPAL-EPL-SD44
570783
VMPAL-EPL-CPX
Cover
Right-hand end plate
Left-hand end plate
Electrical connection: MS2 Electrical interface for multi-pin
plug connection, IP40
Electrical connection: MS1
Electrical connection: MS3
Electrical connection: MF1
Electrical connection: MC
Electrical connection: MS6 Electrical interface for multi-pin
plug connection
Electrical connection: MS8
Electrical connection: CX
1)
42
Pneumatic interface for CPX
terminal
Sub-D, 9-pin,
8 addresses
Sub-D, 25-pin,
24 addresses
Sub-D, 44-pin,
32 addresses
Flat cable, 40-pin,
32 addresses
Terminal strip, 33-pin,
32 addresses
Sub-D, 25-pin,
24 addresses
Sub-D, 44-pin,
32 addresses
32 addresses
A self-adhesive label is supplied.
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
2.5 m
5m
10 m
2.5 m
5m
10 m
2.5 m
5m
10 m
2.5 m
5m
10 m
Up to 30 m
2.5 m
5m
10 m
Up to 30 m
2.5 m
5m
10 m
Up to 30 m
2.5 m
5m
10 m
Up to 30 m
2.5 m
5m
10 m
Up to 30 m
2.5 m
5m
10 m
Up to 30 m
531184
531185
531186
530049
530050
530051
530046
530047
530048
560416
560417
560418
562389
560410
560411
560412
562391
560422
560423
560424
562390
560419
560420
560421
562392
560413
560414
560415
562394
560425
560426
560427
562393
KMP6-09P-08-2,5
KMP6-09P-08-5
KMP6-09P-08-10
KMP6-25P-12-2,5
KMP6-25P-12-5
KMP6-25P-12-10
KMP6-25P-20-2,5
KMP6-25P-20-5
KMP6-25P-20-10
VMPAL-KM-V-SD25-IP67-2,5
VMPAL-KM-V-SD25-IP67-5
VMPAL-KM-V-SD25-IP67-10
VMPAL-KM-V-SD25-IP67-X
VMPAL-KMSK-V-SD25-IP67-2,5
VMPAL-KMSK-V-SD25-IP67-5
VMPAL-KMSK-V-SD25-IP67-10
VMPAL-KMSK-V-SD25-IP67-X
VMPAL-KM-V-SD44-IP67-2,5
VMPAL-KM-V-SD44-IP67-5
VMPAL-KM-V-SD44-IP67-10
VMPAL-KM-V-SD44-IP67-X
VMPAL-KM-S-SD25-IP67-2,5
VMPAL-KM-S-SD25-IP67-5
VMPAL-KM-S-SD25-IP67-10
VMPAL-KM-S-SD25-IP67-X
VMPAL-KMSK-S-SD25-IP67-2,5
VMPAL-KMSK-S-SD25-IP67-5
VMPAL-KMSK-S-SD25-IP67-10
VMPAL-KMSK-S-SD25-IP67-X
VMPAL-KM-S-SD44-IP67-2,5
VMPAL-KM-S-SD44-IP67-5
VMPAL-KM-S-SD44-IP67-10
VMPAL-KM-S-SD44-IP67-X
25-pin
–
560428
VMPAL-KM-SD25-IP67-0
44-pin
–
560429
VMPAL-KM-SD44-IP67-0
570895
NECU-FCG40-K
Connecting cable for multi-pin plug connection with Sub-D plug socket
Connecting cable: DA
Socket 9-pin, Sub-D, open cable end 9-pin
Connecting cable: DB
Connecting cable: DC
–
Socket 25-pin, Sub-D, open cable end 15-pin
–
–
Connecting cable: DD
Socket 25-pin, Sub-D, open cable end 25-pin
Connecting cable: DK
Connecting cable: DJ
Connecting cable: CA
Cable outlet to front
25-pin
(only with left-hand end plate MS6)
Connecting cable: CB
Connecting cable: CC
–
Connecting cable: CQ
Cable outlet to front
25-pin
(only with left-hand end plate MS6)
Connecting cable: CR
Suitable for use with energy chains
Connecting cable: CS
–
Connecting cable: CJ
Cable outlet to front
44-pin
(only with left-hand end plate MS8)
Connecting cable: CK
Connecting cable: CL
–
Connecting cable: CD
Cable outlet to side
25-pin
(only with left-hand end plate MS6)
Connecting cable: CE
Connecting cable: CH
–
Connecting cable: CT
Cable outlet to side
25-pin
(only with left-hand end plate MS6)
Connecting cable: CU
Suitable for use with energy chains
Connecting cable: CV
–
Connecting cable: CM
Cable outlet to side
44-pin
(only with left-hand end plate MS8)
Connecting cable: CN
Connecting cable: CP
–
Cover for multi-pin plug connection without connecting cable with Sub-D plug socket
Electrical multi-pin plug
Cable outlet to side or front
cover: EZ
(only with left-hand end plate MS6)
Electrical multi-pin plug
Outlet either to the side or front
cover: EY
(only with left-hand end plate MS8)
Plug connector
–
2012/06 – Subject to change
Pre-assembled plug connector for flat cable, 40-pin, for flat
cable cross section 0.08 … 0.13 mm2
Internet: www.festo.com/catalog/...
43
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
3 mm
4 mm
6 mm
x†
†
Æ
¼†
3 mm
4 mm
6 mm
x†
†
Æ
¼†
3 mm
4 mm
6 mm
x†
†
Æ
¼†
8 mm
10 mm
12 mm
Ć
y†
½†
8 mm
10 mm
12 mm
Ć
y†
½†
8 mm
132621
132622
132623
132852
132624
132625
132626
132853
132920
132921
132854
132922
132923
132924
132861
132925
132926
132862
132927
132928
132929
132633
132634
132635
132636
132637
132638
132855
132856
132857
132858
132859
132860
132863
QSPKG10-3
QSPKG10-4
QSPKG10-6
QSPKG10-x-U
QSPKG10-Â-U
QSPKG10-Ã-U
QSPKG10-¼-U
QSPLKG10-3
QSPLKG10-4
QSPLKG10-6
QSPLKG10-x-U
QSPLKG10-Â-U
QSPLKG10-Ã-U
QSPLKG10-¼-U
QSPLLKG10-3
QSPLLKG10-4
QSPLLKG10-6
QSPLLKG10-x-U
QSPLLKG10-Â-U
QSPLLKG10-Ã-U
QSPLLKG10-¼-U
QSPKG20-8
QSPKG20-10
QSPKG20-12
QSPKG20-Ä-U
QSPKG20-y-U
QSPKG20-½-U
QSPLKG20-8
QSPLKG20-10
QSPLKG20-12
QSPLKG20-Ä-U
QSPLKG20-y-U
QSPLKG20-½-U
QSPLLKG20-8
10 mm
132864
QSPLLKG20-10
12 mm
132865
QSPLLKG20-12
Ć
132866
QSPLLKG20-Ä-U
y†
132867
QSPLLKG20-y-U
½†
132868
QSPLLKG20-½-U
Cartridge fitting
Standard connection
for valve size 10 mm:
AA
AB
–
AJ
AQ
AK
AL
10 mm cartridge fitting, plastic,
for working lines,
connection for tubing O.D.
–
10 mm cartridge fitting, plastic,
L-shape,
for working lines,
connection for tubing O.D.
–
10 mm cartridge fitting, plastic,
long L-shape,
for working lines,
connection for tubing O.D.
–
20 mm cartridge fitting, plastic,
for supply ports,
connection for tubing O.D.
–
20 mm cartridge fitting, plastic,
L-shape,
for supply ports,
connection for tubing O.D.
–
20 mm cartridge fitting, plastic,
long L-shape,
for supply ports,
connection for tubing O.D.
Adapter
44
Standard connection for
valve size 10 mm: AG
Adapter for 10 mm cartridge fitting connection to
thread M7
10 pieces 572380
VMPAL-F10-M7
–
Adapter for 20 mm cartridge fitting connection to
thread G¼
10 pieces 572381
VMPAL-FSP-G¼
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Part No.
Type
–
Connecting thread G¼ with sealing ring,
with internal hex,
for tubing O.D.
Connecting thread G¼ with sealing ring,
with external hex,
for tubing O.D.
Connecting thread G¼, metal,
with external hex,
for tubing O.D.
6 mm
186108
QS-G¼-6-I
6 mm
8 mm
10 mm
6 mm
8 mm
10 mm
12 mm
8 mm
186097
186099
186101
193411
193412
193413
533848
533930
QS-G¼-6
QS-G¼-8
QS-G¼-10
QS-F-G¼-6
QS-F-G¼-8
QS-F-G¼-10
QS-F-G¼-12
QS-F-G¼-8-I
10 mm
533931
QS-F-G¼-10-I
6 mm
8 mm
10 mm
12 mm
6 mm
533881
533882
533883
533884
186316
QS-F-G¼-6H
QS-F-G¼-8H
QS-F-G¼-10H
QS-F-G¼-12H
QS-VO-G¼-6
8 mm
186317
QS-VO-G¼-8
10 mm
186318
QS-VO-G¼-10
6 mm
153057
QSL-6H
8 mm
153058
QSL-8H
Long push-in sleeve ∅
6 mm
153066
QSL-6HL
Push-in fitting with sealing ring,
connecting thread G¼,
with external hex,
for tubing O.D.
6 mm
186118
QSL-G¼-6
8 mm
186120
QSL-G¼-8
10 mm
186122
QSL-G¼-10
Push-in fitting, metal,
with sealing ring,
connecting thread G¼,
with external hex,
for tubing O.D.
6 mm
193421
QSL-F-G¼-6
8 mm
193422
QSL-F-G¼-8
10 mm
193423
QSL-F-G¼-10
12 mm
533853
QSL-F-G¼-12
Long push-in fitting, metal,
connecting thread G¼,
with external hex,
for tubing O.D.
6 mm
8 mm
10 mm
12 mm
6 mm
556846
556847
556848
556849
186149
QSLL-F-G¼-6
QSLL-F-G¼-8
QSLL-F-G¼-10
QSLL-F-G¼-12
QSLV-F-G¼-6
8 mm
186151
QSLV-F-G¼-8
Push-in fitting
–
–
–
–
Connecting thread G¼, metal,
with internal hex,
for tubing O.D.
Connecting thread G¼, metal,
with push-in sleeve ∅
Connecting thread G¼,
with external hex,
flame-retardant,
for tubing O.D.
Push-in L-connector
–
–
–
2012/06 – Subject to change
Push-in sleeve ∅
Push-in fitting,
connecting thread G¼,
with internal hex,
for tubing O.D.
Internet: www.festo.com/catalog/...
45
-V- New
Valve terminals type 34 MPA-L
Accessories
Ordering data
Code
Description
Push-in fitting, self-sealing
–
Part No.
Type
With sealing ring, with external hex,
connecting thread G¼,
for tubing O.D.
With sealing ring, with external hex,
L shape, connecting thread G¼,
for tubing O.D.
6 mm
8 mm
10 mm
6 mm
8 mm
10 mm
1 piece
1 piece
1 piece
1 piece
1 piece
1 piece
186296
186298
186300
186306
186308
186310
QSK-G¼-6
QSK-G¼-8
QSK-G¼-10
QSKL-G¼-6
QSKL-G¼-8
QSKL-G¼-10
With external hex,
connecting thread G¼,
for tubing O.D.
With external hex, L-shape,
connecting thread G¼,
for tubing O.D.
6 mm
1 piece
186278
QSR-G¼-6
8 mm
1 piece
186280
QSR-G¼-6
6 mm
1 piece
186287
QSRL-G¼-6
8 mm
1 piece
186289
QSRL-G¼-6
1 piece
50 pieces
1 piece
20 pieces
161418
534218
165004
534220
UC-M7
UC-M7-50
UC-¼
UC-¼-20
Thread M7
10 pieces
174309
B-M7
Thread GÅ
10 pieces
3570
B-Å
Rotary push-in fitting
–
Silencer
–
Connecting thread M7
Connecting thread G¼
Blanking plug
–
Inscription label holder/inscription labels
Inscription label holder
for sub-bases: TM
Holder for inscription label IBS-6x10
10 pieces
561109
VMPAL-ST-AP-10
–
Inscription label, 6x10 mm
64 pieces in frame
18576
IBS-6x10
Documentation: DE
Documentation: EN
Documentation: FR
Documentation: ES
Documentation: IT
Documentation: SV
MPA-L Pneumatic Components
German
English
French
Spanish
Italian
Swedish
556353
556354
556356
556355
556357
556358
P.BE-MPAL-DE
P.BE-MPAL-EN
P.BE-MPAL-FR
P.BE-MPAL-ES
P.BE-MPAL-IT
P.BE-MPAL-SV
Manual
46
Internet: www.festo.com/catalog/...
Subject to change – 2012/06
Product Range and Company Overview
A Complete Suite of Automation Services
Our experienced engineers provide complete support at every stage of your development process, including: conceptualization,
analysis, engineering, design, assembly, documentation, validation, and production.
Custom Automation Components
Complete custom engineered solutions
Custom Control Cabinets
Comprehensive engineering support
and on-site services
Complete Systems
Shipment, stocking and storage services
The Broadest Range of Automation Components
With a comprehensive line of more than 30,000 automation components, Festo is capable of solving the most complex
automation requirements.
Electromechanical
Electromechanical actuators, motors,
controllers & drives
Pneumatics
Pneumatic linear and rotary actuators,
valves, and air supply
PLCs and I/O Devices
PLC's, operator interfaces, sensors
and I/O devices
Supporting Advanced Automation… As No One Else Can!
Festo is a leading global manufacturer of pneumatic and electromechanical systems, components and controls for industrial automation,
with more than 12,000 employees in 56 national headquarters serving more than 180 countries. For more than 80 years, Festo has
continuously elevated the state of manufacturing with innovations and optimized motion control solutions that deliver higher performing,
more profitable automated manufacturing and processing equipment. Our dedication to the advancement of automation extends beyond
technology to the education and development of current and future automation and robotics designers with simulation tools, teaching
programs, and on-site services.
Quality Assurance, ISO 9001 and ISO 14001 Certifications
Festo Corporation is committed to supply all Festo products and services that will meet or exceed
our customers’ requirements in product quality, delivery, customer service and satisfaction.
To meet this commitment, we strive to ensure a consistent, integrated, and systematic approach
to management that will meet or exceed the requirements of the ISO 9001 standard for Quality
Management and the ISO 14001 standard for Environmental Management.
© Copyright 2008, Festo Corporation. While every effort is made to ensure that all dimensions and specifications are correct, Festo cannot guarantee that
publications are completely free of any error, in particular typing or printing errors. Accordingly, Festo cannot be held responsible for the same. For Liability and
Warranty conditions, refer to our “Terms and Conditions of Sale”, available from your local Festo office. All rights reserved. No part of this publication may be
reproduced, distributed, or transmitted in any form or by any means, electronic, mechanical, photocopying or otherwise, without the prior written permission of
Festo. All technical data subject to change according to technical update.
Printed on recycled paper at New Horizon Graphic, Inc., FSC certified as an environmentally friendly printing plant.
Festo North America
Festo Regional Contact Center
United States
5300 Explorer Drive
Mississauga, Ontario L4W 5G4
Canada
USA Customers:
For ordering assistance,
Call: 1.800.99.FESTO (1.800.993.3786)
Fax: 1.800.96.FESTO (1.800.963.3786)
Email: customer.service@us.festo.com
For technical support,
Call: 1.866.GO.FESTO (1.866.463.3786)
Fax:
1.800.96.FESTO (1.800.963.3786)
Email: product.support@us.festo.com
USA Headquarters, East: Festo Corp., 395 Moreland Road, Hauppauge, NY 11788
Phone: 1.631.435.0800; Fax: 1.631.435.8026;
Email: info@festo-usa.com
www.festo.com/us
Canadian Customers:
Call: 1.877.GO.FESTO (1.877.463.3786)
Fax:
1.877.FX.FESTO (1.877.393.3786)
Email: festo.canada@ca.festo.com
Canada
USA Headquarters
Festo Corporation
395 Moreland Road
P.O. Box 18023
Hauppauge, NY 11788, USA
www.festo.com/us
USA Sales Offices
Appleton
North 922 Tower View Drive, Suite N
Greenville, WI 54942, USA
Headquarters: Festo Inc., 5300 Explorer Drive, Mississauga, Ontario L4W 5G4
Phone: 1.905.624.9000; Fax: 1.905.624.9001;
Email: festo.canada@ca.festo.com
www.festo.ca
Boston
120 Presidential Way, Suite 330
Woburn, MA 01801, USA
Mexico
Chicago
1441 East Business Center Drive
Mt. Prospect, IL 60056, USA
Dallas
1825 Lakeway Drive, Suite 600
Lewisville, TX 75057, USA
Detroit – Automotive Engineering Center
2601 Cambridge Court, Suite 320
Auburn Hills, MI 48326, USA
New York
395 Moreland Road
Hauppauge, NY 11788, USA
Silicon Valley
4935 Southfront Road, Suite F
Livermore, CA 94550, USA
Headquarters: Festo Pneumatic, S.A., Av. Ceylán 3, Col. Tequesquinahuac,
54020 Tlalnepantla, Edo. de México
Phone:011 52 [55] 53 21 66 00; Fax: 011 52 [55] 53 21 66 65;
Email: festo.mexico@mx.festo.com
www.festo.com/mx
Central USA
Western USA
Festo Corporation
1441 East Business
Center Drive
Mt. Prospect, IL 60056, USA
Phone:1.847.759.2600
Fax: 1.847.768.9480
Festo Corporation
4935 Southfront Road,
Suite F
Livermore, CA 94550, USA
Phone: 1.925.371.1099
Fax:
1.925.245.1286
Festo Worldwide
Argentina
Estonia
Lithuania
Slovakia
Australia
Finland
Malaysia
Slovenia
www.festo.com
Austria
France
Belarus
Germany
Mexico
South Africa
Belgium
Great Britain
Netherlands
South Korea
Brazil
Greece
New Zealand
Spain
Bulgaria
Canada
Chile
Hong Kong
Hungary
India
Norway
Sweden
Peru
Switzerland
Philippines
Taiwan
China
Colombia
Indonesia
Poland
Thailand
Iran
Croatia
Ireland
Romania
Turkey
Czech Republic
Israel
Russia
Ukraine
Italy
Denmark
Japan
Serbia
United States
Latvia
Singapore
Venezuela