Westinghouse WSF6605 User manual

user manual
Dishwasher
WSF6605
2 westinghouse
Electrolux. Thinking of you.
Westinghouse. We are part of the Electrolux family.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety instructions
Product description
Control panel
Use of the appliance
Use of detergent and rinse aid
Loading cutlery and dishes
Setting and starting a washing program
Washing programs
2
4
5
6
6
7
11
13
Care and cleaning
What to do if…
Technical data
Installation
Water connection
Electrical connection
Environment concerns
Warranty
14
15
17
17
18
20
20
21
Subject to change without notice.
SAFETY INSTRUCTIONS
For your safety and correct operation
of the appliance, read this manual
carefully before installation and use. Always keep these instructions with the
appliance even if you move or sell it.
Users must fully know the operation
and safety features of the appliance.
CORRECT USE
• Only use the appliance to clean household utensils that are suitable for dishwashers.
• Do not put solvents in the appliance. Risk
of explosion.
• Put knives and all items with sharp points
in the cutlery basket with their points
down. If not, put them in a horizontal position in the upper basket.
• Use only products specified for dishwashers (e.g. detergent, rinse aid).
• If you open the door while the appliance
is in operation, hot steam can escape.
Risk of skin burns.
• Do not remove dishes from the appliance
before the end of the washing program.
• When the washing program is completed, disconnect the mains plug from the
mains socket and close the water tap.
• Only an authorised service engineer can
repair this appliance. Use only original
spare parts.
• Do not do repairs yourself to prevent injury and damage to the appliance. Always contact the Customer Care Centre.
GENERAL SAFETY
• This appliance is intended to be used in
household and similar applications such
as:
– Staff kitchen areas in shops, offices
and other working environments
– Farm houses
– By clients in hotels, motels and other
residential type environments
– Bed and breakfast type environments.
• Some dishwasher detergents are strongly
alkaline. They can be extremely dangerous if swallowed. Avoid contact with skin
and eyes. Keep the children away from
the appliance when the door is open.
Check that the detergent dispenser is
empty after completion of the washing
program.
• Obey the safety instructions from the
manufacturer of the dishwasher detergent to prevent burns to eyes, mouth and
throat.
• Only put detergent in the dispenser before you start a washing program.
• Do not drink the water from the appliance. Detergent residue can stay in your
appliance.
westinghouse 3
• Always close the door when you do not
use the appliance to prevent injury and
not to stumble over the open door.
• Do not sit or stand on the open door.
CHILD SAFETY
• Do not let persons, children included,
with reduced physical sensory, reduced
mental functions or lack of experience
and knowledge use the appliance. They
must have supervision or instruction for
the operation by a person who is responsible for their safety.
• Children should be supervised to ensure
that they do not play with the appliance.
• Keep all the packaging away from children. There is a risk of suffocation.
• Keep all detergents in a safe area. Do not
let children touch the detergents.
• Keep children and pets away from the
appliance when the door is open.
INSTALLATION
• Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary,
contact the supplier.
• Remove all packaging before first use.
• A qualified and competent person must
do the electrical installation.
• A qualified and competent person must
do the plumbing installation.
• Do not change the specifications or modify this product. Risk of injury and damage to the appliance.
• Do not use the appliance:
– If the mains cable or the water hoses
are damaged.
– If the control panel, worktop or plinth
area are damaged so that you can get
access to the inner side of the appliance.
Contact your local Customer Care Centre.
• Do not drill into the sides of the appliance
otherwise damage to hydraulic and electrical components may occur.
Warning! Follow carefully the
instructions for electrical and water
connections.
4 westinghouse
PRODUCT DESCRIPTION
9
1
8
2
7
6
3
4
1
2
3
4
5
Upper basket
Air vent
Detergent dispenser
Rinse aid dispenser
Rating plate
5
6
7
8
9
Filters
Lower spray arm
Upper spray arm
Worktop
westinghouse 5
CONTROL PANEL
1
2
8
1
2
3
4
5
6
7
8
3
7
6
4
5
On/off button
Program indicators
Display
Indicators
START indicator
START button
DELAY button
PROGRAM button
Indicators
Button LOCK indicator. It comes on when the 'Button LOCK' function is activated.
Rinse Aid indicator. It comes on when it is necessary to fill the rinse aid dispenser.
1)
1) When the rinse aid dispenser is empty, the related indicator does not come on while a washing program operates.
ON/OFF BUTTON
Press this button to switch on or off the appliance.
After 10 minutes from the end of the washing program, the AUTO OFF function automatically switches off the appliance. This
helps to decrease energy consumption.
THE DISPLAY
The display shows:
• The activation and deactivation of the
rinse aid dispenser (only with the multitab
function on)
• The time of the washing program
• The end of a washing program (the display shows a zero)
• The time of the delay start
• The alarm codes.
START BUTTON
Press this button to:
• Start the washing program.
• Start the countdown of the delay start.
• Activate and deactivate the 'Button
LOCK' function.
BUTTON LOCK FUNCTION
The 'Button LOCK' function locks all buttons on the control panel.
To activate the function, press the START
button for approximately 5 seconds. The
'Button LOCK' indicator comes on.
To deactivate the function, press the
START button for approximately 5 seconds.
The 'Button LOCK' indicator goes off.
At the end of the washing program the
'Button LOCK' function is deactivated by
opening and closing the door or switching
off the appliance.
DELAY BUTTON
Press this button to delay the start of the
washing program from 1 to 24 hours. Refer
6 westinghouse
to 'Setting and starting a washing program'.
• To set and start a delay start.
PROGRAM BUTTON
Press this button repeatedly to set a washing program. Each time you press this button, a symbol that is related to a washing
program comes on. Refer to 'Washing programs' chart.
SETTING MODE
The appliance must be in setting mode
for these operations:
• To set and start a washing program.
Switch on the appliance. The appliance
is in setting mode when:
• All the program indicators come on.
Switch on the appliance. The appliance
is not in setting mode when:
• Only one program indicator comes on.
• The display shows the time of a washing
program or a delay start.
– To go back to the setting mode, it is
necessary to cancel the program or
the delay start. Refer to 'Setting and
starting a washing program'.
USE OF THE APPLIANCE
Refer to the specific instructions for
each step of the procedure.
1. Fill the rinse aid dispenser with rinse aid.
2. Load cutlery and dishes into the appliance.
3. Set the correct washing program for the
type of load and soil.
4. Fill the detergent dispenser with the correct quantity of detergent.
5. Start the washing program.
USE OF DETERGENT AND RINSE AID
1
3
2
30
7
4
MA X
+
3 2
-
1
20
Filling with detergent
1. Press the release button 2 to open the
lid 7 of the detergent dispenser.
2. Put the detergent in the dispenser 1 .
3. If the washing program has a prewash
phase, put a small quantity of detergent
on the inner part of the appliance door.
4. If you use the detergent tablets, put the
tablet in the detergent dispenser 1 .
5. Close the detergent dispenser. Press
the lid until it locks into position.
4
6
5
USE OF DETERGENT
Caution! Only use detergents (powder,
liquid or tablet) that are suitable for
dishwashers.
Follow the recommendations on the
detergent packaging for the use and
storage of the detergent.
To help the environment, do not use
more than the correct quantity of detergent.
Different brands of detergent dissolve
in different times. Some detergent tablets do not have the best cleaning results during short washing programs.
Use long washing programs when you
use detergent tablets to fully remove
the detergent.
USE OF RINSE AID
Caution! Only use rinse aid specified
for dishwashers.
Do not fill the rinse aid dispenser with
other products (e.g. dishwasher cleaning agent, liquid detergent). This can
cause damage to the appliance.
westinghouse 7
Rinse aid makes it possible to dry the
dishes without streaks and stains.
Rinse aid is automatically added during the
last rinsing phase.
Follow these steps to fill the rinse aid dispenser:
Filling with rinse aid
1. Press the release button 6 to open the
lid 5 of the rinse aid dispenser.
2. Fill the rinse aid dispenser 3 with rinse
aid. The mark 'max' shows the maximum level.
3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam
during the washing program.
4. Close the rinse aid dispenser. Press the
lid until it locks into position.
ADJUSTING THE RINSE AID DOSAGE
Factory set: position 3.
You can set the rinse aid dosage between
position 1 (lowest dosage) and position 4
(highest dosage).
Turn the rinse aid selector 4 to increase or
reduce the dosage.
Wash hands to remove any residue of
rinse aid from skin.
USE OF COMBI DETERGENT TABLETS
These products are detergents with combined cleaning and rinsing functions. They
can contain also other cleaning agents.
Refer to the instructions from the manufacturer for the use of these products.
When you use tablets that contain rinse
aid:
• Set the lowest position for the rinse aid
dosage.
• Do not put rinse aid in the rinse aid dispenser. In this condition rinse aid indicator light is always on when you switch on
the appliance.
.
Follow these steps if the drying results
are not satisfactory or you want to use
normal detergents again
1. Fill the rinse aid dispenser with rinse aid.
2. Adjust the rinse aid dosage.
LOADING CUTLERY AND DISHES
HELPFUL HINTS AND TIPS
Caution! Only use the appliance for
household utensils that are suitable for
dishwashers.
Do not use the appliance to clean objects
that can absorb water (sponges, household
cloths, etc.).
• Before you load cutlery and dishes:
– Remove all remains of food and debris.
– Soften burnt remains of food.
• While you load cutlery and dishes:
– Load hollow items (e.g. cups, glasses
and pans) with the opening down.
– Make sure that water does not collect
in the container or in a deep base.
– Make sure that cutlery and dishes do
not lie inside one another.
– Make sure that cutlery and dishes do
not cover other cutlery and dishes.
– Make sure that glasses do not touch
other glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick
coatings can retain water droplets. Plastic items do not dry as well as porcelain
and steel items.
• Put light items in the upper basket. Make
sure that the items do not move.
Caution! Make sure that the spray
arms can move freely before you start
a washing program.
Warning! Always close the door after
you load or unload the appliance. An
open door can be dangerous.
LOADING THE LOWER BASKET
Put saucepans, lids, dishes, salad bowls
and cutlery in the lower basket.
The rows of prongs in the lower basket can
be adjusted flat to load large dishes, pots,
pans and bowls.
8 westinghouse
LOADING THE CUTLERY BASKET
Warning! Do not put long-bladed
knives in a vertical position. Arrange
long and sharp cutlery horizontally in
the upper basket. Be careful with sharp
items.
Forks and spoons should be placed in the
removable cutlery basket with the handles
facing downwards and the knives with their
handles facing upwards
XXL
3 x 34 cm
XXL
3x
34 cm
Mix spoons with other cutlery to prevent
them from nesting together.
For best results we recommend you use
the cutlery grids. If the size and dimensions
of the cutlery do not allow the use of the
grids, they can be easily hidden or removed.
westinghouse 9
LOADING THE UPPER BASKET
The upper basket is for plates, saucers, salad bowls, cups and glasses. Arrange the
items to let water touch all surfaces. Put
glasses with long stems in the cup racks
with the stems up. For longer items, fold
the cup racks up.
25
14
cm
cm
10 westinghouse
ADJUSTING THE HEIGHT OF THE
UPPER BASKET
If you put large plates in the lower basket,
first move the upper basket to the upper
position.
24
28
cm
cm
25
30
cm
28
Follow these steps to move the upper
basket to the upper position:
1. Pull the basket out until it stops.
2. Carefully lift the two sides until the
mechanism is engaged and the basket
is stable.
cm
cm
Follow these steps to move the upper
basket to the lower position:
1. Pull the basket out until it stops.
2. Carefully lift the two sides upwards, the
mechanism disengages.
3. Slowly guide the basket back down.
21
cm
22
34
cm
cm
Caution! Do not lift or lower the basket
on one side only.
westinghouse 11
SETTING AND STARTING A WASHING PROGRAM
STARTING THE WASHING PROGRAM
WITHOUT DELAY START
1. Close the appliance door.
2. Switch on the appliance. Make sure that
the appliance is in setting mode.
3. Set a washing program. Refer to 'Washing programs'.
• The related program indicator comes
on.
• All other program indicators go off.
• The time of the program flashes in the
display.
• The START indicator flashes.
4. Press the START button. The washing
program starts.
• The time of the program is no longer
flashing in the display.
• The START indicator is no longer
flashing.
STARTING THE WASHING PROGRAM
WITH DELAY START
1. Close the appliance door.
2. Switch on the appliance. Make sure that
the appliance is in setting mode.
3. Set a washing program.
4. Press the DELAY button repeatedly until
the display shows the time you want to
set for the delay start.
• The time of the delay start flashes in
the display.
5. Press the START button. The countdown starts.
When the countdown is completed, the
washing program starts automatically.
The opening of the appliance door interrupts the countdown. When you
close the door, the countdown continues from the point of interruption.
CANCELLING THE DELAY START
If you have not yet pressed the START
button
1. Press the DELAY button repeatedly until
the display shows the time of the washing program.
2. Press the START button, the washing
program starts.
If the START button has been pressed
and the countdown operates
• Press the DELAY button repeatedly until
the display shows the time of the washing program. After a few seconds the
washing program starts automatically.
Warning! Only interrupt or cancel a
washing program if necessary.
Attention! Open the door carefully.
Hot steam and water can escape.
INTERRUPTING A WASHING
PROGRAM
• Open the appliance door. The washing
program stops.
• Close the appliance door. The washing
program continues from the point of interruption.
CANCELLING THE WASHING
PROGRAM
If you have not yet pressed the START button, you can change the setting.
To change the setting while the washing
program operates, it is necessary to cancel
the program.
• Press and hold the PROGRAM button
and the DELAY button at the same time
until all the program indicators come on.
Make sure that there is detergent in the
detergent dispenser before you start a
new washing program.
END OF THE WASHING PROGRAM
When the washing program is completed,
the display shows 0.
1. Switch off the appliance.
2. Open the appliance door.
For better drying results, keep the appliance door ajar for some minutes.
REMOVING THE LOAD
• Let the dishes cool down before you remove them from the appliance. Hot
dishes are easily damaged.
• First remove items from the lower basket,
then from the upper basket.
12 westinghouse
• There can be water on the sides and
door of the appliance. Stainless steel becomes cool more quickly than the dishes.
westinghouse 13
WASHING PROGRAMS
Program
Type of soil
Type of load
Program description
RINSE
Use this program to quickly rinse the
dishes. This prevents the remaining food
to bond on the dishes and bad odours to
come out from the appliance.
Do not use detergent with this program.
Rinse
FAST30 60°1)
Fresh soil
Crockery and cutlery
Wash 60 °C
Rinse
NORMAL ECO 2)
Normal soil
Crockery and cutlery
Prewash
Wash 50 °C
Rinses
Dry
HEAVY 70°
Heavy soil
Crockery, cutlery,
pots and pans
Prewash
Wash 70 °C
Rinses
Dry
SENSOR
All
Crockery, cutlery,
pots and pans
Prewash
Wash 45 °C or 70 °C
Rinses
Dry
3)
1) With this program you can wash a load with fresh soil. It gives good washing results in a short time.
2) This is the standard program for test institutes. With this program you have the most efficient use of water and
energy consumption for crockery and cutlery with normal soil. Refer to the supplied leaflet for test information.
3) The appliance senses the type of soil and the quantity of items in the baskets. It automatically adjusts the
temperature and quantity of the water, the energy consumption and the program time.
Consumption values
Program1)
Energy (kWh)
Water (litre)
RINSE
0.05
4
FAST30 60°
0.9
9
NORMAL ECO
0.72 - 0.88
10.2 - 12.5
HEAVY 70°
1.4 - 1.6
15 - 16
SENSOR
0.9 - 1.7
8 - 17
1) The display shows the time of the program.
The water pressure and temperature,
the variations of the mains supply and
the quantity of dishes can change the
consumption values.
14 westinghouse
CARE AND CLEANING
TO REMOVE AND CLEAN THE FILTERS
Warning! Switch the appliance off
before you carry out any cleaning
operation.
Dirty filters decrease the washing results.
Although the maintenance is very low with
these filters, we recommend that you regularly check the filters and clean them if necessary.
1. To remove filter (A), turn it counterclockwise and remove it out from filter (B).
7. Put filter (B) to its initial position. Make
sure that it assembles correctly under
the two guides (C).
C
8. Put filter (A) into position in filter (B) and
turn it clockwise until it locks.
B
A
2. Filter (A) has 2 parts. To disassemble
the filter, pull them apart.
CLEANING THE SPRAY ARMS
Do not remove the spray arms.
If the holes in the spray arms become clogged, remove remaining parts of soil with a
thin pointed object.
EXTERNAL CLEANING
Clean the external surfaces of the appliance
and control panel with a damp soft cloth.
Only use neutral detergents. Do not use
abrasive products, scouring pads or solvents (e.g. acetone).
INTERNAL CLEANING
We recommend, every 3 months to run a
washing program for heavily soiled dishes.
Use detergent, but do not put dishes in the
appliance.
3. Thoroughly clean the parts under running water.
4. Put the 2 parts of the filter (A) together
and push. Make sure that they assemble correctly in each other.
5. Remove filter (B).
6. Thoroughly clean filter (B) under running
water.
WHEN THE APPLIANCE IS NOT TO BE
USED FOR A LONG PERIOD
1. Disconnect the mains plug from the
mains socket.
2. Close the water tap.
3. Leave the door open to prevent unpleasant smells.
4. Keep the inner side of the appliance
clean.
westinghouse 15
FROST PRECAUTIONS
Caution! Do not install the appliance
where the temperature is below 0 °C.
The manufacturer is not responsible for
damage caused by frost.
2. Close the water tap.
3. Remove the appliance and the hoses.
4. Do not tilt the appliance during transport.
MOVING THE APPLIANCE
1. Disconnect the mains plug from the
mains socket.
WHAT TO DO IF…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to
the problem yourself. Refer to following
charts. If you cannot find a solution to the
problem, contact your dealer or the Customer Care Centre.
With some malfunctions, the display
shows an alarm code:
Malfunction
The appliance does
not fill with water
The appliance does
not drain the water
•
- The appliance does not fill with water
•
- The appliance does not drain the
water
•
- The anti-flood device operates.
Possible cause
Possible solution
The water tap is closed.
Open the water tap.
The filter in the water inlet hose is
blocked.
Clean the filter.
The installation of the water inlet
hose is not correct. The hose is bent
or squashed.
Make sure that the installation is correct.
The water tap is blocked or restricted with limescale.
Clean the water tap.
The water pressure is too low.
Contact your local water authority.
There is a blockage in the sink spigot.
Clean the sink spigot.
The installation of the water drain
hose is not correct. The hose is bent
or squashed.
Make sure that the installation is correct.
The anti-flood device
operates
The program does
not start
Warning! Switch the appliance off
before you do the suggested corrective
actions.
Close the water tap and contact
your Customer Care Centre.
The appliance door is not closed.
Close the door.
The START button has not been
pressed.
Press the START button.
Mains plug is not connected.
Plug-in the appliance to the mains.
The delay start is set.
• Cancel the delay start.
• Wait until the countdown of the
delay start is completed.
The fuse has blown out in the
household fuse box
Replace the fuse.
16 westinghouse
After the check, switch on the appliance.
The program continues from the point of interruption. If the malfunction occurs again,
contact your Customer Care Centre.
If the display shows an alarm code, not described in the chart, contact your Customer
Care Centre.
When you contact the Customer Care Centre you will need to give some details of the
appliance that can be found on the rating
plate (e.g. model number, serial number,
product number). We recommend that you
record these details.
THE WASHING RESULTS AND DRYING RESULTS ARE NOT SATISFACTORY
Problem
Possible cause
Possible solution
The selected washing program
was not suitable for the type of
load and soil.
Make sure that the washing
program is suitable for the type
of load and soil.
The baskets were not loaded
correctly, water did not touch
all surfaces.
Load the baskets correctly.
The spray arms could not turn
freely because of incorrect arrangement of the load.
Make sure that an incorrect arrangement of the load does not
cause a blockage of the spray
arms.
The filters are dirty or not assembled and installed correctly.
Make sure that the filters are
clean and correctly assembled
and installed.
The quantity of detergent was
not sufficient or missing.
Make sure that the quantity of
detergent is sufficient.
There are streaks, milky stains,
or a bluish layer on glasses and
dishes.
Rinse aid dosage is too high.
Decrease the rinse aid dosage.
Dry water drop stains on
glasses and dishes.
Rinse aid dosage is too low.
Increase the rinse aid dosage.
The detergent can be the
cause.
Use a different brand of detergent.
The dishes are wet and dull.
The rinse aid dispenser is empty.
Fill the rinse aid dispenser with
rinse aid.
The dishes are wet.
You have set a washing program without drying phase or
with a decreased drying phase.
Leave the door ajar for some
minutes before you remove the
dishes.
The dishes are not clean.
westinghouse 17
TECHNICAL DATA
Dimensions
Width
Height
Depth
Electrical connection
Voltage
Overall power
Fuse
Frequency
Water supply pressure
min.
max.
Capacity
Place settings
596 mm
850 mm
620 mm
220-240 V
2200 W
10 A
50 Hz
50 kPa (7 psi)
800 kPa (116 psi)
13
INSTALLATION
FITTING UNDER A KITCHEN COUNTER
Warning! Make sure that the mains
plug is disconnected from the mains
socket during installation.
Put the appliance adjacent to a water tap
and to a water drain.
The plinth of a freestanding appliance is not
adjustable.
Do not remove the worktop of the appliance if you want to use it as a freestanding
unit.
Remove the worktop of the appliance to install it under a kitchen counter (820 mm).
If a repair is necessary, the appliance must
be easily accessible for the engineer.
Make sure that the dimensions of the recess agree with the dimensions in the picture.
REMOVING THE WORKTOP
1. Remove the rear screws (1).
2. Pull the worktop behind the appliance
(2).
3. Lift the worktop and move it from the
front slots (3).
4. Level the appliance using the adjustable feet.
5. Install the appliance under the kitchen
counter. Be careful not to bend or
squash the water hoses and the mains
cable.
ADJUSTING THE LEVEL OF THE
APPLIANCE
A correct adjustment of the level of the appliance allows the door to close and seal
correctly.
18 westinghouse
If the door does not close correctly, loosen
or tighten the adjustable feet to level the appliance.
WATER CONNECTION
WATER INLET HOSE
Connect the inlet hose to a water tap with
an external BSP thread spout of 3/4”.
For best washing performance it is recommended to connect the appliance to a cold
water supply.
Energy savings can be made by connecting
the appliance to a Solar water system and
using economy options, however the water
temperature must not exceed 60 °C.
Once connected the inlet hose to the water
tap, turn the tap on and check that there
are no leaks.
Inlet water supply
• Water pressure: 800 kPa max - 50 kPa
min.
• Water flow rate 10 L / minute min.
• If water pressure is in excess of 800 kPa,
a pressure reducing valve should be
used. Check for leaks.
• If water temperature is in excess of 60
°C, a tempering valve should be used.
Check for leaks.
The water inlet hose is under pressure only
while the water is running. If there is a leak
in the water inlet hose, , the safety valve interrupts the running water.
Be careful when you install the water inlet
hose.
Warning!
• The mains cable is in the doublewalled inlet hose. Do not immerse
the water inlet hose or the safety
valve in water.
• Do not attempt to shorten the inlet
hose.
• If the water inlet hose or the safety
valve is damaged, immediately turn
off the power and remove the mains
plug from the mains socket.
• Only a qualified Service Engineer can
replace the water inlet hose with
safety valve.
Warning! Dangerous voltage
Caution! Always use new hoses when
you connect the appliance to the water
mains. Old hoses must not be used.
The water inlet hose must be examined
at an interval of twelve months for
deterioration and replaced if necessary.
The water pressure must be in the limits,
refer to 'Technical data'.
Make sure that the local water authority
gives you the average mains pressure in
your area.
Make sure that the water inlet hose is not
bent or squashed.
Fit the hose nut correctly to prevent water
leaks.
Caution! Do not connect the appliance
to new pipes or pipes that have been
not used for a long time. Let the water
run for some minutes, then connect the
inlet hose.
The water inlet hose is double-walled and
has an inner mains cable and a safety valve.
WATER DRAIN HOSE
Use the supplied hose clamp to connect
the water drain hose to the sink.
The highest point of the drain hose must be
no more than 600 mm from the floor and
must have a continuous fall to the plumbing
connection.
The drain hose can be lengthened using
additional lengths and connectors. These
must be purchased from Electrolux Spare
Parts. The extension length must not exceed 2 metres.
The drain hose must be free of obstructions.
westinghouse 19
Remove the sink plug when the appliance
drains the water to prevent that the water
goes back into the appliance.
If you connect the water drain hose to a
trap spigot under the sink, remove the plastic membrane. If you do not remove the
membrane, remaining food can cause a
blockage in the drain hose spigot
The appliance has a security feature to
prevent dirty water going back into the
appliance. If, the spigot of the sink has
a 'non-return valve', this valve can
cause the appliance to drain incorrectly. Remove the non-return valve.
Caution! Make sure that the water
couplings are tight to prevent water
leakage.
Ensure that hoses are not bent or
squashed under or behind the appliance.
Once connected the inlet hose to the
water tap, turn the tap on and check
that there are no leaks.
20 westinghouse
ELECTRICAL CONNECTION
Warning!
• The manufacturer accepts no liability
for failure to observe the below safety precautions.
• Safety standards require the appliance to be earthed.
• Prior to using the appliance for the
first time, ensure that the rated voltage and type of supply on the rating
plate match that of the supply where
the appliance is to be installed.
• The fuse rating can be found on the
rating plate and in 'Technical data'.
• Always plug the mains plug onto a
correctly installed approved socket.
• Do not use multi-ways plugs, connectors and extension cables. This
•
•
•
•
can constitute a fire hazard through
overheating.
If necessary, have the domestic wiring system socket replaced. If the
mains cable has to be replaced, contact your local Customer Care centre.
The mains plug must be accessible
after the appliance has been installed.
Never unplug the appliance by pulling on the cable. Always pull the
plug.
Test the appliance. Run a quick
washing program and ensure that
the appliance fills with water, washes
and drains with no leaks.
ENVIRONMENT CONCERNS
The packaging materials are environmentally friendly and can be recycled. The plastic
components are identified by markings, e.g.
>PE<, >PS<, etc. Discard the packaging
materials in the applicable container at the
community waste disposal facilities.
Warning! Follow these instructions to
discard the appliance:
• Pull the mains plug out of the socket.
• Cut off the mains cable and the
mains plug and discard them.
• Discard the door catch. This prevents children from closing themselves inside the appliance and endangering their lives.
OLD APPLIANCE
Make sure that the appliance goes to the
applicable collection point for recycling.
Make sure that this appliance is discarded
correctly. Inappropriate waste discard of
the appliance causes negative consequences for the environment and human health.
For more information about the recycling of
this appliance, contact your local city office,
your household waste disposal service or
the shop where you purchased the appliance.
westinghouse 21
WARRANTY
FOR SALES IN AUSTRALIA AND NEW
ZEALAND
APPLIANCE: DISHWASHER
This document sets out the terms and
conditions of the product warranties
for Electrolux Appliances. It is an important document. Please keep it with
your proof of purchase documents in a
safe place for future reference should
you require service for your Appliance.
1. In this warranty
a) ‘acceptable quality’ as referred to in
clause 10 of this warranty has the
same meaning referred to in the
ACL;
b) ‘ACL’ means Trade Practices
Amendment (Australian Consumer
Law) Act (No.2) 2010;
c) ‘Appliance’ means any Electrolux
product purchased by you accompanied by this document;
d) ‘ASC’ means Electrolux’ authorised
serviced centres;
e) ‘Electrolux’ means Electrolux Home
Products Pty Ltd of 163 O’Riordan
Street, Mascot, NSW 2020, ABN 51
004 762 341 in respect of Appliances purchased in Australia and
Electrolux (NZ) Limited of 3-5 Niall
Burgess Road, Mount Wellington, in
respect of Appliances purchased in
New Zealand;
f) ‘major failure’ as referred to in
clause 10 of this warranty has the
same meaning referred to in the
ACL and includes a situation when
an Appliance cannot be repaired or
it is uneconomic for Electrolux, at its
discretion, to repair an Appliance
during the Warranty Period;
g) ‘Warranty Period’ means:
– where the Appliance is used for
personal, domestic or household
use (i.e. normal single family use)
as set out in the instruction manual, the Appliance is warranted
against manufacturing defects in
Australia for 24 months and in
2.
3.
4.
5.
New Zealand for 24 months, following the date of original purchase of the Appliance;
– this Appliance is not designed for
commercial use and therefore no
warranty applies in this case;
h) ‘you’ means the purchaser of the
Appliance not having purchased the
Appliance for re-sale, and ‘your’ has
a corresponding meaning.
This warranty only applies to Appliances purchased and used in Australia or
New Zealand and is in addition to (and
does not exclude, restrict, or modify in
any way) any non-excludable statutory
warranties in Australia or New Zealand.
During the Warranty Period Electrolux
or its ASC will, at no extra charge if
your Appliance is readily accessible for
service, without special equipment and
subject to these terms and conditions,
repair or replace any parts which it considers to be defective. Electrolux or its
ASC may use remanufactured parts to
repair your Appliance. You agree that
any replaced Appliances or parts become the property of Electrolux. This
warranty does not apply to light globes,
batteries, filters or similar perishable
parts.
Parts and Appliances not supplied by
Electrolux are not covered by this warranty.
You will bear the cost of transportation,
travel and delivery of the Appliance to
and from Electrolux or its ASC. If you
reside outside of the service area, you
will bear the cost of:
a) travel of an authorised representative;
b) transportation and delivery of the
Appliance to and from Electrolux or
its ASC,
In all instances, unless the Appliance is
transported by Electrolux or an Electrolux authorised representative, the Appliance is transported at the owner’s cost
and risk while in transit to and from
Electrolux or its ASC.
22 westinghouse
6. Proof of purchase is required before
you can make a claim under this warranty.
7. You may not make a claim under this
warranty unless the defect claimed is
due to faulty or defective parts or workmanship. Electrolux is not liable in the
following situations (which are not exhaustive):
a) the Appliance is damaged by:
– accident
– misuse or abuse, including failure
to properly maintain or service
– normal wear and tear
– power surges, electrical storm
damage or incorrect power supply
– incomplete or improper installation
– incorrect, improper or inappropriate operation
– insect or vermin infestation
– failure to comply with any additional instructions supplied with
the Appliance;
b) the Appliance is modified without
authority from Electrolux in writing;
c) the Appliance’s serial number or
warranty seal has been removed or
defaced;
d) the Appliance was serviced or repaired by anyone other than Electrolux, an authorised repairer or
ASC.
8. This warranty, the contract to which it
relates and the relationship between
you and Electrolux are governed by the
law applicable where the Appliance
was purchased. Where the Appliance
was purchased in New Zealand for
business purposes the Consumer
Guarantee Act does not apply.
9. To the extent permitted by law, Electrolux excludes all warranties and liabilities
(other than as contained in this document) including liability for any loss or
damage whether direct or indirect arising from your purchase, use or non use
of the Appliance.
10. For Appliances and services provided
by Electrolux in Australia, the Appliances come with a guarantee by Electrolux that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for
any other reasonably foreseeable loss
or damage. You are also entitled to
have the Appliance repaired or replaced if the Appliance fails to be of acceptable quality and the failure does
not amount to a major failure. The benefits to you given by this warranty are in
addition to your other rights and remedies under a law in relation to the Appliances or services to which the warranty relates.
11. At all times during the Warranty Period,
Electrolux shall, at its discretion, determine whether repair, replacement or refund will apply if an Appliance has a valid warranty claim applicable to it.
12. For Appliances and services provided
by Electrolux in New Zealand, the Appliances come with a guarantee by
Electrolux pursuant to the provisions of
the Consumer Guarantees Act, the
Sale of Goods Act and the Fair Trading
Act.
13. To enquire about claiming under this
warranty, please follow these steps:
a) carefully check the operating instructions, user manual and the
terms of this warranty;
b) have the model and serial number
of the Appliance available;
c) have the proof of purchase (eg an
invoice) available;
d) telephone the numbers shown below.
14. You accept that if you make a warranty
claim, Electrolux and its ASC may exchange information in relation to you to
enable Electrolux to meet its obligations
under this warranty.
Important Notice
Before calling for service, please ensure that the steps listed in point 13 above have been
followed.
westinghouse 23
FOR SERVICE
or to find the address of your
nearest state service centre in
Australia
Please call 13 13 4 9
For the cost of a local call (Australia on-
SERVICE AUSTRALIA
ELECTROLUX HOME
PRODUCTS
www.electrolux.com.au
ly)
FOR SERVICE
or to find the address of your
nearest authorised service centre in New Zealand
Free call 0800 10 66 10
(New Zealand only)
FOR SPARE PARTS
or to find the address of your
nearest state spare parts centre in Australia
Please call 13 13 50
For the cost of a local call (Australia only)
SERVICE NEW ZEALAND
ELECTROLUX HOME
PRODUCTS
www.electrolux.co.nz
FOR SPARE PARTS
or to find the address of your
nearest state spare parts centre in New Zealand
Free call 0800 10 66 20
(New Zealand only)
www.westinghouse.com.au
117914630-A-232012