DSTV DECODER SETUP MANUAL July 2013

DSTV DECODER SETUP MANUAL
July 2013
www.jemic.co.za
DSTV SINGLE VIEW AND SD PVR
DECODER SETUP
How to program your Single View and SD PVR DSTV Decoders
STEP 1 Ensure that the DSTV decoder is connected correctly to the outlet
socket, as well as to the Television set.
Once the connecting of decoder and television has been completed
switch on decoder. The decoder will go through setup procedures.
Once the decoder has completed scanning, you should receive a picture
and audio on Decoder Channel 100 (See example on the left).
STEP 2 Push the MENU button on the DSTV Remote Control.
The “Main Menu” screen will appear on the Television Screen.
(See example on the left)
STEP 3 Use the Arrow Keys on the DSTV Remote Control to scroll down to the
“Advances Options” tab on the Menu.
Push the OK button on the DSTV Remote Control
2 www.jemic.co.za
STEP 4 The “Advanced Options” Menu will now be displayed (See example on
the left).
Ensure that the “Dish Installation” tab is highlighted in yellow.
Push the OK button on the DSTV Remote Control.
STEP 5 The “Security Check” Menu will now be displayed. (See example on the
left).
Enter the Pin Code using the numeric (0 to 9) buttons on the DSTV
Remote Control.
PIN Code: 9949
STEP 6 The “Dish Installation” Menu will now be displayed. (See example on
left).
The “Home Network” tab will be highlighted in yellow.
Ensure that the option in the tab is set to DStv IS7. (If not, use the left
and right arrow keys on the DSTV Remote Control to change to the
correct option).
Push the OK button on the DSTV Remote Control.
To Change any of the parameters in the various Network Setups, The following procedures
should be followed:
 Use the Up/Down arrow keys on the DSTV Remote Control to move the yellow bar to the parameter
to be changed.
 Push the OK button - ½ of the yellow bar will turn white allowing the parameter to be edited.
 Use Left/Right arrow keys to delete or modify parameters. Use the numeric keys (0 to 9) to enter
values.
 Once parameters have been changed, push the OK button - The bar will change back to yellow.
Repeat these steps until all parameters have been changed to the correct values.
3 www.jemic.co.za
STEP 7 The “Home Network” Menu will now be displayed. (See example on the
left).
Check all parameters. Ensure that the parameters displayed are identical
to the parameters shown in the example on the left.
Once parameters have been checked move the yellow bar down to the
“Accept all displayed values and leave screen” tab.
Push the OK Button on the DSTV Remote Control.
Parameters for the Home Network are now saved. The Decoder will
return to the “Dish Installation” Menu.
STEP 8 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 2 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control.
STEP 9 Change all parameters for Network 2 as shown on the left.
Frequency
Symbol Rate
FEC
Polarisation
Use NIT
10730
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 2 are now saved. The Decoder will return to
the “Dish Installation” Menu.
STEP 10 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 3 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control.
4 www.jemic.co.za
STEP 11 Change all parameters for Network 3 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
10810
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 3 are now saved. The Decoder will return to
the “Dish Installation” Menu.
STEP 12 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 4 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control.
STEP 13 Change all parameters for Network 4 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
10930
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 4 are now saved. The Decoder will return to
the “Dish Installation” Menu
STEP 14 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 5 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control.
5 www.jemic.co.za
STEP 15 Change all parameters for Network 5 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11210
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 5 are now saved. The Decoder will return to
the “Dish Installation” Menu
STEP 16 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 6 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control
STEP 17 Change all parameters for Network 6 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11250
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 6 are now saved. The Decoder will return to
the “Dish Installation” Menu
STEP 18 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to More Networks (See example on the left).
Push the OK Button on the DSTV Remote Control
6 www.jemic.co.za
STEP 19 Ensure that Network 7 is highlighted by the yellow bar (See example on
the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control
STEP 20 Change all parameters for Network 7 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11290
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 7 are now saved. The Decoder will return to
the “Dish Installation” Menu
STEP 21 STEP 22 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to More Networks (See example on the left).
Push the OK Button on the DSTV Remote Control
Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 8 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control
7 www.jemic.co.za
STEP 23 Change all parameters for Network 8 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11330
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 8 are now saved. The Decoder will return to
the “Dish Installation” Menu
STEP 24 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to More Networks (See example on the left).
Push the OK Button on the DSTV Remote Control
STEP 25 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 9 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control
STEP 26 Change all parameters for Network 9 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11370
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 9 are now saved. The Decoder will return to
the “Dish Installation” Menu
8 www.jemic.co.za
STEP 27 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to More Networks (See example on the left).
Push the OK Button on the DSTV Remote Control
STEP 28 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Network 10 (See example on the left).
Use the Right Arrow Button on the DSTV Remote Control to change the
network to “DStv IS7”.
Push the OK Button on the DSTV Remote Control
STEP 29 Change all parameters for Network 10 as shown on the left.
Frequency
Symbol Rate
FEC
Polarization
Use NIT
11410
30000
5/6
Vertical
SMATV
Once all the correct parameters have been entered move the yellow bar
to the “Accept all displayed values and leave screen” tab and push the
OK Button on the DSTV Remote Control.
Parameters for the Network 10 are now saved. The Decoder will return
to the “Dish Installation” Menu
STEP 30 Use the Down Arrow Button on the DSTV Remote Control to move the
yellow bar to Scan All Networks (See example on the left).
Push the OK Button on the DSTV Remote Control.
9 www.jemic.co.za
STEP 31 The DSTV Decoder will proceed to scan all networks (See example on
the left)
Once the scan process is complete and all information has been saved,
the DSTV Decoder will return to normal operation automatically.
STEP 32 The DSTV Decoder should now function normally and have access to all
DSTV Television and Audio services.
10 www.jemic.co.za
DSTV 4P HD PVR and 2P HD
DECODER SETUP
How to Connect your DSTV HD PVR Decoder (4 Input): PVR
Equipment Required* 1 x 4 Way IF‐Splitter (5‐2150MHz) 5 x Cable or Flylead (F to F) *Available at your local TV parts/service shop or contact Tect for a quotation. Please complete for the following steps: 1. Connect and F‐Connector flylead to the satellite output on the wall outlet plate. 2. The other side of the flylead gets connected to the input of the 4 way IF‐Splitter. 3. The 4 Outputs of the 4 Way Splitter gets connected to the 4 LNB Inputs on the back of the HD Decoder. 4. Connect the yellow, white and red AV leads to the corresponding colours on the back of the HD Decoder and into the corresponding coloured inputs on the TV (AV1), or preferably with the HDMI cable supplied with the HD Decoder. 5. To watch TV select the AV1 or the HDMI input selection on the TV remote control. How to Connect your DSTV 2P HD PVR Decoder (2 Input): Equipment Required* 1 x 2 Way IF‐Splitter (5‐2150MHz) 3 x Cable or Flylead (F to F) *Available at your local TV parts/service shop or contact Tect for a quotation. Please complete for the following steps: 1. Connect and F‐Connector flylead to the satellite output on the wall outlet plate. 2. The other side of the flylead gets connected to the input of the 2 way IF‐Splitter. 3. The 2 Outputs of the 2 Way Splitter gets connected to the 2 LNB Inputs on the back of the 2P HD Decoder. 4. Connect the yellow, white and red AV leads to the corresponding colours on the back of the 2P HD Decoder and into the corresponding coloured inputs on the TV (AV1), or preferably with the HDMI cable supplied with the HD Decoder. 5. To watch TV select the AV1 or the HDMI input selection on the TV remote control. 11 www.jemic.co.za
Before entering the various network setups into the HD PVR it is very important to do a factory reset of the decoder via the Engineering Screen (Green Screen Reboot): This reset is required to ensure your decoder functions correctly. As the factory reset will affect personal settings such as aspect ratio, RF output and Extra View Setup. It is important to make a note of these settings in your decoder before doing the factory reset so that the personal settings can be restored once the factory reset has been completed. PACE (Black) 4P HD PVR UEC (Silver) 4P HD PVR 2P HD PVR Follow these steps on the Push and hold the “GUIDE” Push and hold the “GUIDE” Push and hold the Decoder front panel and button for at least 10 button for at least 10 “TV/AUDIO” button for at seconds. least 10 seconds. not by using the remote seconds. Push the “EXIT” button Push the “SHIFT”, “GUIDE” Push the “UHF” and control. followed by the “OK” button and the “OK” buttons in “PLAY/PAUSE” buttons in in quick succession. quick succession. quick succession. The Engineering Screen login will appear (See example on the left) Enter the PIN CODE 1649 by using the decoder remote control. Click on the “ACCEPT” TAB The Engineering Screen Installations Menu will appear (See example on the left) Select the “Factory Settings” option by using the decoder remote control. Use the decoder remote control to select the “Restore Factory Settings” option in the following menu (See example on the left) Push “OK” on the remote The Engineering Screen login will appear (See example on the left) Enter the PIN CODE 1649 by using the decoder remote control. Click on the “ACCEPT” TAB The Engineering Screen Installations Menu will appear (See example on the left) Select the “Factory Settings” option by using the decoder remote control. Use the decoder remote control to select the “Restore Factory Settings” option in the following menu (See example on the left) Push “OK” on the remote The Engineering Screen login will appear (See example on the left) Enter the PIN CODE 1649 by using the decoder remote control. Click on the “ACCEPT” TAB The Engineering Screen Installations Menu will appear (See example on the left) Select the “Factory Settings” option by using the decoder remote control. Use the decoder remote control to select the “Restore Factory Settings” option in the following menu (See example on the left) Push “OK” on the remote Use the decoder remote control to select the “Accept” tap (See example on the left) Push “OK” on the remote Use the decoder remote control to select the “Accept” tap (See example on the left) Push “OK” on the remote Use the decoder remote control to select the “Accept” tap (See example on the left) Push “OK” on the remote The HD PVR Decoder will now restore factory defaults. Once completed wait until the decoder has rebooted before starting decoder setup. The HD PVR Decoder will now restore factory defaults. Once completed wait until the decoder has rebooted before starting decoder setup. The HD PVR Decoder will now restore factory defaults. Once completed wait until the decoder has rebooted before starting decoder setup. 12 www.jemic.co.za
STEP 1 Ensure that the HD-PVR decoder is connected correctly to the outlet socket in the
apartment, as well as to the Television set.
Once the connecting of decoder as television has been completed switch
on decoder. The decoder will go through setup procedures.
Once the decoder has completed scanning, you should receive a picture
and audio on Decoder Channel 100 (See example on the left).
STEP 2 Push the MENU button on the HD-PVR Remote Control.
The “Decoder Menu” screen will appear on the Television Screen.
(See example on the left)
STEP 3 Use the Arrow Keys on the HD-PVR Remote Control to scroll to the
“Advances Options” tab on the Menu.
Push the OK button on the HD-PVR Remote Control
STEP 4 The “Enter Installation PIN” Menu will now be displayed (See example
on the left).
Enter the Pin Code using the numeric (0 to 9) buttons on the DSTV
Remote Control.
PIN Code: 9949
13 www.jemic.co.za
STEP 5 The “Advanced Options” Menu will now be displayed. (See example on
the left).
Ensure that the “Network Set-up” tab is highlighted in yellow.
Push the OK button on the HD-PVR Remote Control
STEP 6 The “Home Network” Menu will now be displayed. (See example on the
left).
Check all parameters. Ensure that the parameters displayed are identical
to the parameters shown in the example on the left.
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 1” menu.
STEP 7 The “Additional Network 1” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 1
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 8 Enabled
SMATV
10730
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 2” menu.
The “Additional Network 2” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 2
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
Enabled
SMATV
10770
30000
2/3
Vertical
8PSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 3” menu.
14 www.jemic.co.za
STEP 9 The “Additional Network 3” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 3
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 10 Enabled
SMATV
10810
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 4” menu.
The “Additional Network 4” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 4
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 11 Enabled
SMATV
10850
30000
2/3
Vertical
8PSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 5” menu.
The “Additional Network 5” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 5
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 12 Enabled
SMATV
10890
30000
2/3
Vertical
8PSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 6” menu.
The “Additional Network 6” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 6
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
Enabled
SMATV
10930
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 7” menu.
15 www.jemic.co.za
STEP 13 The “Additional Network 7” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 7
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 14 Enabled
SMATV
11210
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 8” menu.
The “Additional Network 8” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 8
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 15 Enabled
SMATV
11250
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 9” menu.
The “Additional Network 9” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 9
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 16 Enabled
SMATV
11290
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 10” menu.
The “Additional Network 10” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 10
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
Enabled
SMATV
11330
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 11” menu.
16 www.jemic.co.za
STEP 17 The “Additional Network 11” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 11
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
STEP 18 Enabled
SMATV
11370
30000
5/6
Vertical
QPSK
Push the P+ Button on the HD-PVR Remote Control to move to
“Additional Network 12” menu.
The “Additional Network 12” Menu will now be displayed. (See example
on the left).
Use the Right Arrow Button to “Enable” Additional Network 11
Use the Arrow Buttons on the HD-PVR Remote Control to change
parameters as shown in example on the left.
Signal Set-up
Use NIT
Network Frequency
Symbol Rate
FEC
Polarization
Modulation
Enabled
SMATV
11410
30000
5/6
Vertical
QPSK
Push the (Yellow) Button on the HD-PVR Remote Control to Scan all
enabled networks
STEP 19 The HD-PVR will now automatically scan all enabled networks. (See
example on the left)
Once the scan process is complete and all information has been saved,
the HD-PVR Decoder will return to normal operation automatically.
The HD-PVR Decoder should now function normally and have access to
all DSTV Television and Audio services.
STEP 19 The HD-PVR Decoder should now function normally and have access to
all DSTV Television and Audio services.
17 www.jemic.co.za