installation operation and maintenance manual heated display cases

INSTALLATION
OPERATION
AND
MAINTENANCE
MANUAL
ED2-48
HEATED
DISPLAY CASES
FULL SERVICE OR
ED2-72
SELF SERVICE
EUROPEAN STYLE
ED2-96
SERIES:
ED2-48
ED2-72
ED2-96
W 1 6 4 N 9 2 2 1 W a t e r S t r e e t • P.O. Box 450 • Menomonee Falls, Wisconsin 53052-0450 USA
PHONE: 262.251.3800
FAX: 262.251.7067 • 800.329.8744 U.S.A. ONLY
WEBSITE:
262.251.1907 INTERNATIONAL
www.alto-shaam.com
800.558-8744 USA/CANADA
PRINTED IN U.S.A.
#868 • 1/2005
HEATED DISPLAY CASES
®
U N PA C K I N G & S E T- U P
The Alto-Shaam Heated Display Case has
been thoroughly tested, checked for
calibration, and inspected to insure only the
highest quality unit is provided. When you
receive your case, check for any possible
shipping damage and report it at once to the
delivering carrier. See Transportation Damage
The BU2 Cart is designed to fit under
the ED2 Display Cases
®
®
and Claims section located in this manual.
EU2SYS-48
Front View
ED2-48 on
BU2-48 Cart
with optional
casters
In order to maintain established National
Sanitation Foundation standards, all stationary floor models
must be sealed to the floor with a R.T.V. or silastic meeting
N.S.F. requirements or have 6" (153mm) unobstructed
clearance beneath the unit.
Counter and table units must be mounted on legs of a
sufficient 4" (102mm) height to provide minimum
unobstructed space beneath the unit. These legs are
supplied with the unit. Warranty will become null and void
if these directions are not followed.
Save all the information and instructions packed inside the
display case. Complete and return the warranty card to the
factory as soon as possible to assure prompt service in the
event of a warranty parts and labor claim.
NOTE:
EU2SYS-48
Rear View
ED2-48 on
BU2-48 Cart
with shelf
Any and all claims for warranty must include the
full model and serial number of the display case.
E L E C T R I C A L I N S TA L L AT I O N
If necessary, permanent wiring or electrical outlets for
this display case must be installed by an licensed electrician
in accordance with local, country or national codes.
PH
PATENT NOS. 3521030
4595247
®
An identification tag is permanently mounted on case.
Plug the case into a properly grounded receptacle ONLY.
Arcing will occur when connecting or disconnecting the
display case unless all controls are in the OFF position.
Always position the appliance so the power supply cord is
easily accessible in case of emergency.
EU2SYS-48
Rear View
ED2-48 on
BU2-48 Cart
with 750-TH
cook/hold oven
ENSURE THE POWER SOURCE
MATCHES THE VOLTAGE STAMPED
ON CABINET NAMEPLATE
REGARDING INTERNATIONAL STANDARD UNITS:
If the unit is not equipped with flexible cord with plug,
an all-pole country approved disconnection device which
has a contact separation of at least 3mm in all poles must
be incorporated in the fixed wiring for disconnection.
When using a cord without a plug, the green/yellow
conductor shall be connected to the terminal which is
marked with the ground symbol. If a plug is used, the
socket outlet must be easily accessible. If the power
cord needs replacement, use a similar one obtained
from the distributor.
For 230V units: To prevent an electrical shock hazard
between the appliance and other appliances or metal parts
in close vicinity, an equalization-bonding stud is provided.
An equalization bonding lead must be connected to this
stud and the other appliances / metal parts to provide
sufficient protection against potential difference. The
terminal is marked with the following symbol.
ED2SYS-48
with standard black panels
#868 • ED2 Series Operation & Care Manual • 1
I N S TA L L AT I O N
OUTSIDE DIMENSIONS - ED2SYS
27-3/16" (691mm)
32-15/16" (837mm)
34-1/4" (870mm)
44-5/16" (1125mm)
47-11/16" (1212mm)
4" (102mm)
26-7/16" (672mm)
26-1/8" (664mm)
ED2SYS
PROFILE VIEW
29-3/4" (756mm)
ED2
PROFILE VIEW
ELECTRICAL PANEL
3" (76mm) ADJUSTABLE
PEGS IN EACH CORNER
ELECTRICAL OUTLET
47-11/16" (1212mm)
20-3/16"
(513mm)
26-1/8" (664mm)
47-1/8" (1196mm)
3" (76mm) ADJUSTABLE
PEGS IN EACH CORNER
ELECTRICAL PANEL
ELECTRICAL OUTLET
26-1/8" (664mm)
47-11/16" (1212mm)
20-3/16"
(513mm)
48" (1219mm)
3" (76mm) ADJUSTABLE
PEGS IN EACH CORNER
96" (2438mm)
#868 • ED2 Series Operation & Care Manual • 2
ELECTRICAL PANEL
ELECTRICAL OUTLET
26-1/8" (664mm)
47-11/16" (1212mm)
20-3/16"
(513mm)
72" (1829mm)
I N S TA L L AT I O N
OUTSIDE DIMENSIONS - EU2SYS
5-1/2"
(140mm)
5-1/2"
(140mm)
Swivel
Caster
Swivel
Caster
48" (1219mm)
ELECTRICAL PANEL
ELECTRICAL
OUTLET
57" (1448mm)
30-1/2" (775mm)
26-1/2" (673mm)
32-1/2" (824mm)
5-1/2"
(140mm)
ELECTRICAL PANEL
ELECTRICAL OUTLET
57" (1448mm)
30-1/2" (775mm)
57" (1448mm)
30-1/2" (775mm)
26-1/2" (673mm)
44-5/16" (1125mm)
Swivel
Caster
Rigid
Caster
Swivel
Caster
5-1/2"
(140mm)
Swivel
Caster
Rigid
Caster
96" (2438mm)
#868 • ED2 Series Operation & Care Manual • 3
Swivel
Caster
ELECTRICAL PANEL
ELECTRICAL
OUTLET
57" (1448mm)
30-1/2" (775mm)
26-1/2" (673mm)
72" (1829mm)
I N S TA L L AT I O N
OPTIONS AND ACCESSORIES
DESCRIPTION
ED2-48
SERIES
ED2-72
SERIES
ED2-96
SERIES
CARVING STATION
ELECTRICAL OUTLET
5001874
5001781
5001874
5001781
5001874
5001781
FRAME TRIM KIT, STAINLESS STEEL, TOP
5001281
5001282
5001283
FRAME TRIM KIT, WHITE, TOP
5000938
5001284
5001285
GAUGE, INTERIOR AMBIENT
ED2-48, ED2-48/P
AVAILABLE
—
—
TEMPERATURE
ED2-72, ED2-72/P
—
5001144
—
ED2-72/PL
—
5001146
—
ED2-72/PR
—
5001145
—
ED2-96
—
—
5001147
ED2-96/PL
—
—
5001149
—
—
5001148
factory quote
factory quote
factory quote
GLASS, SOLAR COOL BRONZE END PANES
5001143
5001143
5001143
PAN, 4" DEEP SELF-SERVICE
1001990
1001991
—
ED2-96/PR
GLASS, TEMPERED END SPACER
FOR BUTTING MULTIPLE CASES
PANEL, CUSTOM COLOR, BASE
ED2SYS
P154
P155
P156
EU2SYS
P111
P112
P113
P148
P152
P153
ED2SYS
5001293
5001295
5001297
EU2SYS
5001287
5001289
5001291
ED2SYS
5001292
5001294
5001296
PANEL, CUSTOM COLOR, TOP
PANEL, STAINLESS STEEL, BASE
PANEL, WHITE, BASE
PLATFORM, SCALE
EU2SYS
5001286
5001288
5001290
CUSTOMER VIEW RIGHT - HAND
5001307
5001307
5001307
CUSTOMER VIEW LEFT - HAND
5001308
5001308
5001308
ED2-48, ED2-48/P
5002802
—
—
ED2-72, ED2-72/P
—
5002803
—
ED2-72/PL/PR
—
5002804
—
ED2-96
—
—
5002805
ED2-96/PL/PR
—
—
5002806
5001430
5001430
5001430
SHEET PAN, DIVIDER BAR PACKAGE
SHELF, STAINLESS STEEL
EU2SYS
ED2-48 Heated Display Case
with optional carving station and
interior temperature gauge
#868 • ED2 Series Operation & Care Manual • 4
O P E R AT I O N
OPERATING PROCEDURES
1. DO NOT ADD WATER TO DISPLAY CASE
Halo Heat display cases maintain a constant but
gentle temperature and eliminate much of the
moisture loss associated with conventional display
cases. Because of this gentle heat, it is not
necessary to add water to the display case. As a
matter of fact, adding water is not
recommended since water will accelerate the
deterioration of the product, and may damage the
unit voiding the warranty.
2. PLACE DIVIDERS AND SERVING PANS IN CASE
Refer to the pan layout diagrams for different
types of pan accommodations. A complete pan
configuration layout is located in this manual. It
is VERY important to note, no matter what
type of pan configuration chosen, pan separator
bars or divider bars must be used to close all gaps
between pans, and all gaps between the pans and
the edges of the display case. If these gaps are
not closed, heat will escape from the bottom of the
case into the display area. As a consequence, heat
distribution will be uneven and uniform
temperature will be difficult to hold. If needed,
additional pan divider bars are available. The
supplied self-serve pan inserts with wire grids are
for use with pre-packaged foods in the self-serve
sections of the units.
3. TURN DISPLAY LIGHTS “ON” AND SET
THE THERMOSTAT(S) AT NUMBER “10”
TO PREHEAT
A indicator light will illuminate when the
thermostat(s) is (are) turned “ON.” The
indicator(s) will remain lit as long as the unit is
preheating or calling for heat. The unit should be
preheated at the 10 setting for a minimum of 3045 minutes before loading the case with hot food.
When preheating is completed, or whenever the
unit reaches any temperature set by the operator
between 1 and 10, the indicator light(s) will go
“OUT”.
4. LOAD HOT FOODS INTO DISPLAY CASE
Be certain only hot food is transferred into the
display case. Before loading food into the case,
use a pocket-type meat thermometer to make
certain all products have reached an internal
temperature of 140° to 160° F (60° to 71°C). If
any food product is not at proper serving
temperature, use a Halo Heat cooking and holding
oven, set at 250° to 275°F (121° to 135°C), or a
Combitherm oven to bring the product within the
correct temperature range.
Use hand protection when handling hot items.
Be certain only hot PREPACKAGED foods in
appropriate heat tested containers are used in
the self-service section of the display case.
Do not stack food containers.
5. RESET THERMOSTAT(S) AS NEEDED
After all products are loaded into the display case
and the doors are closed, it is necessary to reset
the thermostat(s). For fully enclosed sections, reset
the thermostat to the number “8” setting. Cases
with a self-service section should be maintained
between number “9” and number “10” for the selfservice section only. THESE SETTINGS WILL
NOT NECESSARILY BE FINAL. Since proper
temperature range depends on the type of
products and the quantities being held, it is
necessary to periodically use a pocket
thermometer to check each item to make certain
the correct temperatures are being maintained.
Proper temperature range is between a minimum
of 140° and 160° F (60° and 71° C). Normally,
this will require a thermostat setting of between
number “6” and “8” in fully enclosed cases. Selfservice cases or sections will always require a
higher thermostat setting.
6. PLACEMENT OF FOOD PROBE
If the unit is equipped with the probe accessory,
wipe each probe and probe tip with a disposable
alcohol pad to clean and sanitize before using. If
the probe is left in its bracket, the LED
temperature display will indicate the ambient air
temperature inside the case. To place a probe
into food kept in the case, remove the probe from
the bracket and push the probe tip halfway into
the product, positioning the tip at the center of
the food mass. If placing into solid foods such as
meat roast or poultry breasts, push the probe in
from a straight downward position or in from the
side to the center position. If placing into a semiliquid or liquid product, the probe cable will
probably need to be secured to keep the probe
positioned properly. Do not let the probe tip
touch the edges or sides. Tape the probe cable to
the lip or edge of the container. Wipe each probe
tip with a clean paper towel to remove food debris
after each use. Follow by wiping probes with a
disposable alcohol pad, and return each probe to
the proper bracket position.
7. SERVE FRESH HOT FOOD
Keep hot foods looking fresh. Occasionally stir or
rotate food as needed. Serve food products in
appropriate heat tested packages or containers.
Keep display case doors closed after serving.
Wipe spills immediately to assure maximum eye
appeal and to ease end of the day cleanup.
#868 • ED2 Series Operation & Care Manual • 5
O P E R AT I O N
ED2 Series Controls
Indicator Lights
LI-3025 (120V/208-240V)
LI-3951 (230V)
Light Switch
SW-33896
Cutting Board
Bracket
Thermostats
TT-3498
BT-2342
Operator/Control side with cutting board
Electrical Cord
CD-33490 (230V)
CD-3291 (120/208-240V)
Plug
Thermostat
TT-3498
Cutting Board
4016
#868 • ED2 Series Operation & Care Manual • 6
PG-3267
(C OUNTERTOP U NITS ,
120/208-240V O NLY )
O P E R AT I O N
PAN CONFIGURATIONS • HEATED DISPLAY CASES
ED2-72
ED2-96
ED2-48
GN 1/2
FULL-SIZE PAN
12" x 20" x 2-1/2" (325mm x 530mm x 65mm)
GN1/1
ONE-HALF SIZE PAN
12" x 10" x 2-1/2" (325mm x 265mm x 65mm)
GN1/2
TWO-THIRDS SIZE PAN
12" x 14" x 2-1/2" (325mm x 352mm x 65mm)
GN2/3
ONE -THIRD SIZE PAN
12" x 6" x 2-1/2" (325mm x 176mm x 65mm)
GN1/3
— 48 MODELS: Up to 6 One-Half Size Pans with 3 One-Third Size Pans per display case
— 72 MODELS: Up to 5 One-Half Size Pans with 5 One-Third Size Pans per display case
— 96 MODELS: Up to 7 One-Half Size Pans with 7 One-Third Size Pans per display case
One (1) FULL-SIZE PAN and one (1) ONE-THIRD SIZE PAN per pan zone.
— 48 MODELS: Up to 3 Two-Thirds Size Pans with 6 One-Third Size Pans per display case
— 72 MODELS: Up to 5 Two-Thirds Size Pans with 10 One-Third Size Pans per display case
— 96 MODELS: Up to 7 Two-Thirds Size Pans with 14 One-Third Size Pans per display case
One (1) TWO-THIRDS SIZE PAN and two (2) ONE-THIRD SIZE PANS per pan zone.
— 48 MODELS: Up to 12 One-Third Size Pans per display case
— 72 MODELS: Up to 20 One-Third Size Pans per display case
— 96 MODELS: Up to 28 One-Third Size Pans per display case
Four (4) ONE-THIRD SIZE PAN per pan zone.
STANDARD PAN SIZES
One (1) FULL-SIZE PAN and one (1) ONE-THIRD SIZE PAN per pan zone.
—
—
4
—
15
5
—
6
21
7
FULL, HALF AND THIRD SIZE-SHORT
NOTE: ADDITIONAL PAN SEPARATOR
BARS MAY BE REQUIRED TO
ACCOMMODATE MAXIMUM CAPACITIES.
— 48 MODELS: Up to 3 Full-Size Pans with 3 One-Third Size Pans per display case
— 72 MODELS: Up to 5 Full-Size Pans with 5 One-Third Size Pans per display case
— 96 MODELS: Up to 7 Full-Size Pans with 7 One-Third Size Pans per display case
1
4
—
9
3
3-1/4" x 7"
3-11/16" x 28"
3" x 28"
1" x 12-3/4"
2-7/16" x 12-3/4"
ONE-THIRD SIZE PAN
FULL, HALF AND THIRD SIZE-LONG
FULL, HALF AND THIRD SIZE-LONG
FULL, HALF AND THIRD SIZE-SHORT
11318
1002621
#868 • ED2 Series Operation & Care Manual • 7
72
(83mm x 178mm)
(93mm x 711mm)
(76mm x 711mm)
(25mm x 324mm)
(62mm x 324mm)
48
11047
1002584
1002590
ONE-THIRD
SIZE PAN
GN 1/3
ONE-THIRD
SIZE PAN
ONE-THIRD
SIZE PAN
ONE-THIRD
SIZE PAN
ONE-HALF
SIZE PAN
ONE-THIRD
SIZE PAN
GN 2/3
GN 1/1
MODELS
STANDARD PAN DIVIDER and SEPARATOR BARS
96
DIMENSIONS
DESCRIPTION
NO.
GN 1/2
FULL-SIZE
PAN
ONE-THIRD
SIZE PAN
ONE-THIRD
SIZE PAN
TWO-THIRDS
SIZE PAN
ONE-THIRD
SIZE PAN
ONE-HALF
SIZE PAN
7 PAN ZONES
5 PAN ZONES
3 PAN ZONES
O P E R AT I O N
PAN CONFIGURATIONS • SELF-SERVE HOT DISPLAY CASES
ED2SYS-96/PL
ED2SYS-96/PR
➔
ED2SYS-72/PL & ED2SYS-72/PR
➔
PA N LA YOUT
DIA GRA M
5 PAN ZONES
3 PAN ZONES
ONE-THIRD
ONE-HALF
SIZE PAN
TWO-THIRDS
SIZE PAN
SELF-SERVE
PAN ZONE
SIZE PAN
ONE-THIRD
SIZE PAN
FULL-SIZE
PAN
ONE-HALF
SIZE PAN
PAN SIZE: ITEM #1405
16-7/8" x 26-1/2 x 2"
(429 mm x 673 mm x 51 mm)
ONE-THIRD
SIZE PAN
SIZE PAN
ONE-THIRD
SIZE PAN
SIZE PAN
Two (2) ONE-HALF SIZE PANS and
One (1) ONE-THIRD SIZE PAN per pan zone .
— 72 MODELS: Up to 6 One-Half Size Pans with
3 One-Third Size Pans per display case
— 96 MODELS: Up to 10 One-Half Size Pans with
5 One-Third Size Pans per display case
One (1) TWO-THIRDS SIZE PAN and
Two (2) ONE-THIRD SIZE PANS per pan zone .
— 72 MODELS: Up to 3 Two-Thirds Size Pans with
6 One-Third Size Pans per display case
— 96 MODELS: Up to 5 Two-Thirds Size Pans with
10 One-Third Size Pans per display case
Four (4) ONE-THIRD SIZE PANS per pan zone .
— 72 MODELS: Up to 12 One-Third Size Pans
per display case
— 96 MODELS: Up to 20 One-Third Size Pans
per display case
➔
➔
ONE-THIRD
SIZE PAN
➔
ONE-THIRD
SIZE PAN
➔
ONE-THIRD
One (1) FULL-SIZE PAN and
One (1) ONE-THIRD SIZE PAN per pan zone .
— 72 MODELS: Up to 3 Full-Size Pans with
3 One-Third Size Pans per display case
— 96 MODELS: Up to 5 Full-Size Pans with
5 One-Third Size Pans per display case
SHEET PANS
(NOT SHOWN)
STANDARD PAN SIZES
FULL-SIZE PAN
12" x 20" x 2-1/2"
ONE-THIRD
➔
FULL-SIZE SHEET PANS: 18" x 26" x 1"
— 72 MODELS: 2 Sheet Pans per display case
— 96 MODELS: 3 Sheet Pans per display case
STANDARD PAN DIVIDER & SEPARATOR BARS
GN 1/1
325 mm x 530 mm x 65 mm
ONE-HALF SIZE PAN
GN 1/2
12" x 10" x 2-1/2" 325 mm x 265 mm x 65 mm
TWO-THIRDS SIZE PAN
GN 2/3
12" x 14" x 2-1/2" 325 mm x 352 mm x 65 mm
Item No.
Description
Dimensions (W x L)
Models
72
96
––
––
3-1/4" x 7"
(83 mm x 178 mm)
1002584 FULL, HALF & THIRD SIZE-LONG
3-11/16" x 28"
(93 mm x 711 mm)
4
1002590 FULL, HALF & THIRD SIZE-LONG
3" x 28"
(76 mm x 711 mm)
––
6
1002621 FULL, HALF & THIRD SIZE-SHORT
2-7/16" x 12-3/4"
(62 mm x 324 mm)
5
7
1" x 12-3/4"
(25 mm x 324 mm)
15
21
11047 ONE-THIRD SIZE PAN
11318 FULL, HALF & THIRD SIZE-SHORT
ONE-THIRD SIZE PAN
GN 1/3
12" x 6" x 2-1/2"
325 mm x 176 mm x 65 mm
FULL-SIZE SHEET PAN
N/A
457 mm x 660 mm x 25,4 mm
18" x 26" x 1"
#868 • ED2 Series Operation & Care Manual • 8
––
O P E R AT I O N
1002585
1000544
1002619
Part No.
1002585
1002591
1002619
1000544
International pan divider and separator bars
GN 1/1, GN 1/2, GN 1/3 - Long
GN 1/1, GN 1/2, GN 1/3 - Long
GN 1/4
GN 1/1, GN 1/2, GN 1/3 - Short
93 mm x 711 mm
76 mm x 711 mm
50 mm x 283 mm
50 mm x 610 mm
Models
48
72
4
4
6
10
9
15
1002619 (1)
1000544 (5)
1002585 (4)
#868 • ED2 Series Operation & Care Manual • 9
96
6
14
21
O P E R AT I O N
GENERAL HOLDING GUIDELINES
Chefs, cooks and other specialized food service
personnel employ varied methods of cooking.
Proper holding temperatures for a specific food
product must be based on the moisture content of the
product, product density, volume, and proper serving
temperatures. Safe holding temperatures must also
be correlated with palatability in determining the
length of holding time for a specific product.
Halo Heat maintains the maximum amount of
product moisture content without the addition of
water, water vapor, or steam. Maintaining maximum
natural product moisture preserves the natural flavor
of the product and provides a more genuine taste. In
addition to product moisture retention, the gentle
properties of Halo Heat maintain a consistent
temperature throughout the cabinet without the
necessity of a heat distribution fan, thereby
preventing further moisture loss due to evaporation
or dehydration.
In an enclosed holding environment, too much
moisture content is a condition which can be
relieved. A product achieving extremely high
temperatures in preparation must be allowed to
decrease in temperature before being placed in a
controlled holding atmosphere. If the product is not
allowed to decrease in temperature, excessive
condensation will form increasing the moisture
content on the outside of the product.
Most Halo Heat Holding Equipment is provided with
a thermostat control between 60° and 200°F
(16° to 93°C). If the unit is equipped with vents,
close the vents for moist holding and open the vents
for crisp holding.
HOLDING TEMPERATURE RANGE
MEAT
BEEF ROAST — Rare
BEEF ROAST — Med/Well Done
BEEF BRISKET
CORN BEEF
PASTRAMI
PRIME RIB — Rare
STEAKS — Broiled/Fried
RIBS — Beef or Pork
VEAL
HAM
PORK
LAMB
FAHRENHEIT
140°F
160°F
160° — 175°F
160° — 175°F
160° — 175°F
140°F
140° — 160°F
160°F
160° — 175°F
160° — 175°F
160° — 175°F
160° — 175°F
CELSIUS
60°C
71°C
71° — 79°C
71° — 79°C
71° — 79°C
60°C
60° — 71°C
71°C
71° — 79°C
71° — 79°C
71° — 79°C
71° — 79°C
POULTRY
CHICKEN — Fried/Baked
DUCK
TURKEY
GENERAL
160°
160°
160°
160°
FISH/SEAFOOD
FISH — Baked/Fried
LOBSTER
SHRIMP — Fried
160° — 175°F
160° — 175°F
160° — 175°F
71° — 79°C
71° — 79°C
71° — 79°C
BAKED GOODS
BREADS/ROLLS
120° — 140°F
49° — 60°C
MISCELLANEOUS
CASSEROLES
DOUGH — Proofing
EGGS —Fried
FROZEN ENTREES
HORS D'OEUVRES
PASTA
PIZZA
POTATOES
PLATED MEALS
SAUCES
SOUP
VEGETABLES
160° — 175°F
80° — 100°F
150° — 160°F
160° — 175°F
160° — 180°F
160° — 180°F
160° — 180°F
180°F
180°F
140° — 200°F
140° — 200°F
160° — 175°F
71°
27°
66°
71°
71°
71°
71°
—
—
—
—
175°F
175°F
175°F
175°F
71°
71°
71°
71°
—
—
—
—
79°C
79°C
79°C
79°C
— 79°C
— 38°C
— 71°C
— 79°C
— 82°C
— 82°C
— 82°C
82°C
82°C
60° — 93°C
60° — 93°C
71° — 79°C
THE HOLDING TEMPERATURES LISTED ARE SUGGESTED GUIDELINES.
If the unit is equipped with a thermostat indicating a
range of between 1 and 10, use a metal-stemmed
indicating thermometer to measure the internal
temperature of the product(s) being held. Adjust the
thermostat setting to achieve the best overall setting
based on internal product temperature.
#868 • ED2 Series Operation & Care Manual • 10
CARE AND CLEANING
The cleanliness and appearance of
this equipment will contribute
considerably to operating
efficiency and savory, appetizing
food. Good equipment that is kept
clean works better and lasts longer.
1. CLEAN THE PROBES DAILY
If the display case is supplied with
probes, remove all food soil from probes.
Wipe entire probe and cable assembly
with warm detergent solution and a clean
cloth. Remove detergent by wiping each
probe and cable with clean rinse water
and a cloth. Wipe probes with
disposable alcohol pad or sanitizing solution
recommended for food contact surfaces. Allow
probe and cable to air dry in probe holding
bracket.
2. THOROUGHLY CLEAN THE UNIT DAILY
A. Turn lights and adjustable thermostat(s) to the
“OFF” position, and disconnect unit from
power source.
B. Remove, cover or wrap, and store unused
products under refrigeration.
C. Clean the interior metal surfaces of the cabinet
with a damp clean cloth and any good
commercial detergent or grease solvent at the
recommended strength. Use a plastic scouring
pad or oven cleaner for difficult areas. Rinse
well to remove all residue and wipe dry.
SAFETY ALERT
This units performance has been
optimized using the factory provided
bulbs. These bulbs should be
replaced with an exact replacement
or with a factory recommended replacement.
These bulbs have been treated to resist breakage
and must be replaced with similarly treated bulbs
in order to maintain compliance with NSF
standards. Do not over-tighten bulbs in
their receptacles as this can cause
damage to the bulb filament.
NOTE: Avoid the use of abrasive cleaning
compounds, chloride based cleaners, or
cleaners containing quaternary salts. Never
use hydrochloric acid (muriatic acid) on
stainless steel.
D. Clean the glass with a window cleaner. The
sliding glass doors are removable allowing for
easier cleaning.
E. To help maintain the protective film coating on
polished stainless steel, clean the exterior of
the unit with a cleaner recommended for
stainless steel surfaces. Spray the cleaning
agent on a clean cloth and wipe with the grain
of the stainless steel.
Always follow appropriate state or local health
(hygiene) regulations regarding all applicable cleaning
and sanitation requirements for equipment.S
DO NOT USE IF CONTROLS ARE NOT
PROPERLY FUNCTIONING
Refer to the Trouble Shooting Guide located in this
manual or call an authorized service technician.
CHECK OVERALL CONDITION ONCE
A MONTH
Check the case and related cabinets once a month for
physical damage and loose screws. Correct any
problems before they begin to interfere with the
operation of the unit.
AT NO TIME SHOULD THE INSIDE OR
THE OUTSIDE OF THE OVEN BE
WASHED DOWN, FLOODED WITH
WATER, OR LIQUID SOLUTION. DO
NOT USE WATER JET TO CLEAN.
NEVER STEAM CLEAN.
S E V E R E DAMAGE OR ELECTRICAL HAZARD
COULD RESULT.
WARRANTY BECOMES VOID IF
CABINET IS FLOODED.
H o o d g l a s s ex t e n d e d t o t h e f u l l u p r i g h t
position is stabilized through the use
of gas str uts designed for the full
load bearing weight. These struts
C A U T I O N
c o u l d w e a k e n o r f a i l d u e t o w e a r,
e nv i r o n m e n t a l c o n d i t i o n s o r a g i n g .
Operators should be aware of any decrease in effort to lift
the hood and initiate an immediate gas strut safety check.
!
D O N OT L I F T T H E H O O D I N T H I S C O N D I T I O N .
#868 • ED2 Series Operation & Care Manual • 11
S A N I TAT I O N
SANITATION GUIDELINES
Food flavor and aroma are usually so closely related
that it is difficult, if not impossible, to separate them.
There is also an important, inseparable relationship
between cleanliness and food flavor. Cleanliness, top
operating efficiency, and appearance of equipment
contribute considerably to savory, appetizing foods.
Good equipment that is kept clean, works better and
lasts longer.
Most food imparts its own particular aroma and many
foods also absorb existing odors. Unfortunately,
during this absorption, there is no distinction
between GOOD and BAD odors. The majority of
objectionable flavors and odors troubling food service
operations are caused by bacteria growth. Sourness,
rancidity, mustiness, stale or other OFF flavors are
usually the result of germ activity.
The easiest way to insure full, natural food flavor is
through comprehensive cleanliness. This means
good control of both visible soil (dirt) and invisible
soil (germs). A thorough approach to sanitation will
provide essential cleanliness. It will assure an
attractive appearance of equipment, along with
maximum efficiency and utility. More importantly, a
good sanitation program provides one of the key
elements in the prevention of food-borne illnesses.
A controlled holding environment for prepared foods
is just one of the important factors involved in the
prevention of food-borne illnesses. Temperature
monitoring and control during receiving, storage,
preparation, and the service of foods are of equal
importance.
The most accurate method of measuring safe
temperatures of both hot and cold foods is by
internal product temperature. A quality thermometer
is an effective tool for this purpose, and should be
routinely used on all products that require holding at
a specific temperature.
A comprehensive sanitation program should focus on
the training of staff in basic sanitation procedures.
This includes personal hygiene, proper handling of
raw foods, cooking to a safe internal product
temperature, and the routine monitoring of internal
temperatures from receiving through service.
Most food-borne illnesses can be prevented through
proper temperature control and a comprehensive
program of sanitation. Both these factors are
important to build quality service as the foundation of
customer satisfaction. Safe food handling practices
to prevent food-borne illness is of critical importance
to the health and safety of your customers.
HACCP, an acronym for Hazard Analysis (at) Critical
Control Points, is a quality control program of
operating procedures to assure food integrity, quality,
and safety. Taking steps necessary to augment food
safety practices are both cost effective and relatively
simple. While HACCP guidelines go far beyond the
scope of this manual, additional information is
available by contacting:
Center for Food Safety and Applied Nutrition
Food and Drug Administration
1-888-SAFEFOOD.
INTERNAL FOOD PRODUCT TEMPERATURES
HOT FOODS
DANGER ZONE
40° TO 140°F
CRITICAL ZONE 70° TO 120°F
SAFE ZONE 140° TO 165°F
(4° TO 60°C)
(21° TO 49°C)
(60° TO 74°C)
COLD FOODS
DANGER ZONE
SAFE ZONE
ABOVE 40°F
36°F TO 40°F
(ABOVE 4°C)
(2°C TO 4°C)
FROZEN FOODS
DANGER ZONE
CRITICAL ZONE
SAFE ZONE
ABOVE 32°F
0° TO 32°F
0°F OR BELOW
(ABOVE 0°C)
(-18° TO 0°C)
(-18°C OR BELOW)
#868 • ED2 Series Operation & Care Manual • 12
SERVICE
ED2 Series - Service Views
Control Panel Access
Switch
Thermostat
SW-33896
TT-3498
Fuses
Switch
Thermostat
FU-3775
SW-33896
TT-3498
Cutting Board Bracket
Indicator Light
BT-2342
LI-3025 (120V/208-240V)
LI-3951 (230V)
Indicator Light
LI-3025 (120V/208-240V)
LI-3951 (230V)
Control Panel for Model ED2-48
Cable Wrap:
Access by removal
of bottom panel
CB-3045
#868 • ED2 Series Operation & Care Manual • 13
SERVICE
ED2 Series - Service Views
Bulb Receptacles
RP-3955 (230V)
RP-3952 (120/208-240V)
Inside the top - lights
LP-3384 (230V)
LP-33592 (120/208-240V)
Manual Temperature Gauge (O PTION )
5001144 (ED2-72, -72/P)
5001145 (ED2-72/PR)
5001146 (ED2-72/PL)
5001147 (ED2-96)
5001148 (ED2-96/PR)
5001149 (ED2-96/PL)
Glass
GL-25420
(F ULL S ERVICE ) :
ED2-48, -72/PL, -72/PR, -96
GL-25430
(S ELF S ERVICE ) :
ED2-72/PL, -72/PR, -96/PL, -96/PR
GL-25586 (S ELF S ERVICE ) : ED2-48/P
GL-25785 (F ULL S ERVICE ) :
ED2-72, -96/PL, -96/PR
Extrusion
Gasket
GL-25889
GS-22547
(S ELF S ERVICE ) : ED2-72/P
Pivot Hinge
HG-23669
Strut Pack Assembly
Glass Clamp
CM-25421
#868 • ED2 Series Operation & Care Manual • 14
SERVICE
Cable Replacement Kits
ED2-48 Series
Cable Replacement Kit
Cable Heating Service Kit No. 4880
includes:
CB-3045
Cable Heating Element . . . . . . . . . .134 feet
CR-3226
Ring Connector . . . . . . . . . . . . . . . . . . . .4
IN-3488
Insulation Corner
. . . . . . . . . . . . . . .1 foot
BU-3105
Shoulder Bushing
. . . . . . . . . . . . . . . . . .4
BU-3106
Cup Bushing . . . . . . . . . . . . . . . . . . . . . .4
SL-3063
Insulating Sleeve . . . . . . . . . . . . . . . . . . .4
TA-3540
High Temperature Tape . . . . . . . . . . .1 roll
ST-2439
Stud, 10/32 . . . . . . . . . . . . . . . . . . . . . .4
NU-2215
Hex Nut . . . . . . . . . . . . . . . . . . . . . . . . .8
ED2-72 Series
Cable Replacement Kit
Cable Heating Service Kit No. 4881
includes:
CB-3045
Cable Heating Element
CR-3226
Ring Connector
. . . . . . . .210 feet
IN-3488
Insulation Corner . . . . . . . . . . . . . .1 foot
BU-3105
Shoulder Bushing . . . . . . . . . . . . . . . .12
BU-3106
Cup Bushing
SL-3063
Insulating Sleeve . . . . . . . . . . . . . . . . .12
TA-3540
High Temperature Tape
ST-2439
Stud, 10/32 . . . . . . . . . . . . . . . . . . . .12
NU-2215
Hex Nut
. . . . . . . . . . . . . . . . .12
SAFETY ALERT
This units performance has been
optimized using the factory provided
bulbs. These bulbs should be
replaced with an exact
replacement or with a factory
recommended replacement. These bulbs have
been treated to resist breakage and
must be replaced with similarly
treated bulbs in order to maintain
compliance with NSF standards.
. . . . . . . . . . . . . . . . . . .12
. . . . . . . . .1 roll
. . . . . . . . . . . . . . . . . . . . . .24
DISCONNECT UNIT FROM
POWER SOURCE BEFORE
CLEANING OR SERVICING
ED2-96 Series
Cable Replacement Kit
Cable Heating Service Kit No. 14228
includes:
CB-3045
Cable Heating Element . . . . . . . . . .280 feet
CR-3226
Ring Connector . . . . . . . . . . . . . . . . . . . .8
IN-3488
Insulation Corner
. . . . . . . . . . . . . . .1 foot
BU-3105
Shoulder Bushing
. . . . . . . . . . . . . . . . . .8
BU-3106
Cup Bushing . . . . . . . . . . . . . . . . . . . . . .8
SL-3063
Insulating Sleeve . . . . . . . . . . . . . . . . . . .8
TA-3540
High Temperature Tape . . . . . . . . . . .1 roll
ST-2439
Stud, 10/32 . . . . . . . . . . . . . . . . . . . . . .8
NU-2215
Hex Nut . . . . . . . . . . . . . . . . . . . . . . . .16
#868 • ED2 Series Operation & Care Manual • 15
1. CORD, (120/240V), 7' (2133mm)
CORD, (230V), 7' (2133mm)
PLUG (COUNTERTOP UNITS, 120/240V
ED
2S
Y
S48
/P
ED
2S
Y
S48
ED
248
/P
Alto-Shaam
Part No.
Part Description
ED
248
ED2-48 Series
CD-3291
CD-33490
PG-3267
1
1
1
1
1
1
1
1
-
1
1
-
IN-2203
2
2
2
2
3. HEATING CABLE, 132' (40234mm)
CB-3045
X
X
X
X
4. THERMOSTAT
THERMOSTAT KNOB
THERMOSTAT, BEZEL
TT-3498
KN-3473
TT-3713
2
2
2
2
2
2
2
2
2
2
2
2
LI-3025
LI-3951
2
2
2
2
2
2
2
2
SW-33896
SW-3905
2
2
2
2
2
2
2
2
FU-3772
FU-3775
1
2
1
2
-
-
TERMINAL BLOCK, SYS ONLY
CONTACT FACTORY
-
-
X
X
9. TERMINAL BLOCK, MODULAR
BK-25432
1
1
-
-
10. BULBS (120/240V)
BULBS (230V)
LP-33592
LP-3384
6
6
6
6
6
6
6
6
RP-3952
RP-3955
6
6
6
6
6
6
6
6
12. END GLASS GASKET, 7' (2133mm) ED2-48
END GLASS GASKET, 3' (914mm) ED2-48/P
GS-22547
GS-22547
1
-
2
1
-
2
13. DOOR, GLASS, LEFT HAND
DOOR, GLASS, MID or RIGHT HAND
DR-25422
DR-25423
1
1
1
1
1
1
1
1
14. TRACK, TOP
TRACK, BOTTOM
TK-25417
TK-25418
1
1
1
1
1
1
1
1
15. GLASS, FULL SERVE, W / SILK SCREEN , 48" (1219mm)
GLASS, END, CLEAR
GLASS, SELF SERVE (ED2-48/P)
CLAMP, GLASS
LATCH, GLASS, RETAINING
HANDLE, GLASS (ED2-48)
FRAME, GLASS, LEFT HAND
FRAME, GLASS, RIGHT HAND
GL-25420
GL-25762
GL-25586
CM-25421
LT-2195
1001656
5000241
5000242
1
2
1
2
1
1
1
2
1
1
2
1
1
1
2
1
2
1
1
1
2
1
1
2
1
1
16. HINGE, PIVOT
HG-23669
2
2
2
2
4016
11283
BT-2342
1
2
2
1
2
2
1
2
2
1
2
2
18. HEAT GUARD, PASS THRU
GD-25577
-
1
-
1
19. PAN
PAN
PAN
PAN
PN-25752
1000993
-
2
1
-
2
1
SU-24021
PI-23678
PI-23679
BU-2827
PG-2899
2
2
2
4
4
2
4
4
2
2
2
4
4
2
4
4
LG-2044
4
4
4
4
ST-24173
1
1
1
1
ONLY )
2. INSULATION
1/2" x 24" x 48" (13mm x 610mm x 1219mm)
5.
INDICATOR LIGHT (120/240V), RED
INDICATOR LIGHT (230V), WHITE
6. SWITCH, BULB
RUBBER BOOT FOR SWITCH, 230V
ONLY
7. FUSE HOLDER
FUSE, 15 AMP
8.
11. RECEPTACLE, BULB (120/240V)
RECEPTACLE, BULB (230V)
17. CUTTING BOARD ASSEMBLY
CUTTING BOARD BRACKET BASE
CUTTING BOARD BRACKET
GRID, PASS THRU
INSERT, 2" DEEP (51mm)
DIVIDER, LONG SEE PAGES 7, 8, 9
DIVIDER, SHORT SEE PAGES 7, 8, 9
20. GAS STRUT, 95#
PIN, HINGE ANCHOR
PIN, STRUT PIVOT
BUSHING, BEARING, NYLON
PLUG, WEAR
21. LEGS, 4" (102mm)
22. EQUIPOTENTIAL STUD (230V)
#868 • ED2 Series Operation & Care Manual • 16
1. CORD, (120/240V), 7' (2133mm)
CORD, (230V), 7' (2133mm)
PLUG ( COUNTERTOP UNITS , 120/240V
ED
272
/P
R
ED
2S
YS
-7
2
ED
2S
YS
-7
2/
ED
P
2S
YS
-7
2/
PL
ED
2S
YS
-7
2/
PR
ED
272
/P
L
Alto-Shaam
Part No.
ED
272
/P
Part Description
ED
272
ED2-72 Series
CD-3557
CD-33490
PG-3267
1
1
1
1
1
1
1
1
1
1
1
1
1
1
-
1
1
-
1
1
-
1
1
-
IN-2203
2
2
2
2
2
2
2
2
3. HEATING CABLE, 210' (64008mm)
CB-3045
X
X
X
X
X
X
X
X
4. THERMOSTAT
THERMOSTAT KNOB
THERMOSTAT, BEZEL
TT-3498
KN-3473
TT-3713
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
LI-3027
LI-3951
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
SW-33896
SW-3905
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
FU-3772
FU-3775
1
2
1
2
1
2
1
2
-
-
-
-
SYS ONLY
CONTACT FACTORY
-
-
-
-
X
X
X
X
9. TERMINAL BLOCK, MODULAR
TERMINAL BLOCK, 120V ONLY
BK-25432
BK-3021
1
1
1
1
1
1
1
1
-
-
-
-
10. BULBS (120/240V)
BULBS (230V)
LP-33592
LP-3384
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
RP-3952
RP-3955
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
10
12. END GLASS GASKET, 7' (2133mm)
END GLASS GASKET, 3' (914mm) ED2-72/P
GS-22547
GS-22547
7'
-
3'
7'
-
7'
-
7'
-
3'
7'
-
7'
-
13. DOOR, GLASS, LEFT HAND
DOOR, GLASS, MID
DOOR, GLASS, RIGHT HAND
DR-25422
DR-25423
DR-25424
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
14. TRACK, TOP
TRACK, BOTTOM
TK-25569
TK-25792
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
15. GLASS, CENTER, DIVIDER, PL/PR
GL-22049
GLASS, FULL SERVE, W/SILK SCREEN, 72"(1829mm) GL-25785
GLASS, SELF-SERVE, 24" (610mm) (72/PL; 72/PR) GL-25430
GLASS, END, CLEAR
GL-25762
GLASS, FULL SERVE (72 PR/PL), 48" (1219mm) GL-25420
GLASS, SELF SERVE (72/P)
GL-25889
CLAMP, GLASS
CM-25789
LATCH, GLASS, RETAINING
LT-2195
HANDLE, GLASS, EXTRUSION, 72" (1829mm) 1001657
HANDLE, GLASS, EXTRUSION
1001656
FRAME, GLASS, LEFT HAND
5000241
FRAME, GLASS, RIGHT HAND
5000242
1
2
1
2
1
1
1
2
1
1
2
-1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
1
2
1
2
1
1
1
2
1
1
2
1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
16. HINGE, PIVOT
HG-23669
2
2
2
2
2
2
2
2
4017
11283
BT-2342
1
2
2
1
2
2
1
2
2
1
2
2
1
2
2
1
2
2
1
2
2
1
2
2
18. HEAT GUARD, PASS THRU UNITS
GD-25899
GD-24852
-
1
-
1
1
-
1
-
1
1
19. PAN
PAN
PAN
PAN
PAN
PAN
PN-25752
1000735
1000521
1001991
-
3
1
1
1
1
-
1
1
-
-
3
1
1
1
1
-
1
1
-
SU-22431
SU-22702
PI-23678
PI-23679
BU-2827
PG-2899
2
1
2
4
4
2
4
2
4
4
1
1
4
2
4
4
1
1
4
2
4
4
2
1
2
4
4
2
4
2
4
4
1
1
4
2
4
4
1
1
4
2
4
4
ONLY )
2. INSULATION
1/2" x 24" x 48" (13mm x 610mm x 1219mm)
5. INDICATOR LIGHT (120/208-240V),
INDICATOR LIGHT (230V), WHITE
6. SWITCH, BULB
RUBBER BOOT FOR SWITCH, 230V
RED
ONLY
7. FUSE HOLDER
FUSE, 15 AMP
8. TERMINAL BLOCK,
11. RECEPTACLE, BULB (120/240V)
RECEPTACLE, BULB (230V)
17. CUTTING BOARD ASSEMBLY, 6' (1829mm)
CUTTING BOARD BRACKET BASE
CUTTING BOARD BRACKET
GRID, PASS THRU
INSERT, 2" DEEP (51mm)
INSERT
INSERT, 4" DEEP (102mm)
DIVIDER, LONG SEE PAGES 7, 8, 9
DIVIDER, SHORT SEE PAGES 7, 8, 9
20. GAS STRUT, 50# ( SELF - SERVE GLASS )
GAS STRUT, 140#
PIN, HINGE, ANCHOR
PIN, STRUT PIVOT
BUSHING, BEARING, NYLON
PLUG, WEAR
21. LEGS, 4" (102mm)
22. EQUIPOTENTIAL STUD (230V)
LG-2044
4
4
4
4
-
-
-
-
ST-24173
1
1
1
1
1
1
1
1
#868 • ED2 Series Operation & Care Manual • 17
ED
296
ED
296
/P
L
ED
296
/P
R
ED
2S
YS
-9
6
ED
2S
YS
-9
6/
PL
ED
2S
YS
-9
6/
PR
CD-3557
CD-33489
PG-3267
1
1
1
1
1
1
1
1
1
1
1
-
1
1
-
1
1
-
IN-2203
3
3
3
3
3
3
HEATING CABLE, 277.5' (84572mm)
CB-3045
X
X
X
X
X
X
4.
THERMOSTAT
THERMOSTAT KNOB
THERMOSTAT, BEZEL
TT-3498
KN-3473
TT-3713
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
5.
INDICATOR LIGHT, (110V), RED
INDICATOR LIGHT (230V), WHITE
LI-3027
LI-3951
3
3
3
3
3
3
3
3
3
3
3
3
6.
SWITCH, BULB
RUBBER BOOT FOR SWITCH, 230V
SW-33896
SW-3905
3
3
3
3
3
3
3
3
3
3
3
3
FU-3772
FU-3775
1
2
1
2
1
2
-
-
-
BK-25432
BK-3021
1
1
1
1
1
1
-
-
-
CONTACT FACTORY
-
-
-
X
X
X
LP-33592
LP-3384
14
14
14
14
14
14
14
14
14
14
14
14
RP-3952
RP-3955
14
14
14
14
14
14
14
14
14
14
14
14
12. GLASS END, GASKET, 7' (2134 mm)
GS-22547
7'
7'
7'
7'
7'
7'
13. DOOR, GLASS, LEFT HAND
DOOR, GLASS, MID
DOOR, GLASS, RIGHT HAND
DR-25422
DR-25423
DR-25424
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
1
2
1
14. TRACK, TOP
TRACK, BOTTOM
TK-25791
TK-25793
1
1
1
1
1
1
1
1
1
1
1
15. GLASS, CENTER, DIVIDER, PASS THRU UNITS
GL-22049
GLASS, FULL SERVE,W/SILK SCREEN, 48 " (1219mm) GL-25420
GLASS, SELF-SERVE, 24" (610mm)
GL-25430
GLASS, END, CLEAR
GL-25762
GLASS, FULL SERVE (PR/PL)
GL-25785
CLAMP, GLASS
CM-25790
LATCH, GLASS, RETAINING
LT-2195
HANDLE, GLASS, EXTRUSION
1001658
HANDLE, GLASS EXTRUSION (PL/PR)
1001657
FRAME, GLASS, LEFT HAND
5000241
FRAME, GLASS, RIGHT HAND
5000242
2
2
1
2
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
2
2
1
2
1
1
1
1
1
2
1
1
2
1
1
1
1
1
2
1
1
2
1
1
1
16. HINGE, PIVOT
HG-23669
2
2
2
2
2
2
4016
11283
BT-2342
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
2
4
4
18. HEAT GUARD, PASS THRU UNITS
GD-24852
-
1
1
-
1
1
19. PAN
PAN
PAN
PAN
PN-25752
1000521
-
1
1
1
1
-
1
1
1
1
SU-22431
SU-22704
PI-23678
PI-23679
BU-2827
PG-2899
2
4
2
4
4
1
1
4
2
4
4
1
1
4
2
4
4
2
4
2
4
4
1
1
4
2
4
4
1
1
4
2
4
4
LG-2044
6
6
6
-
-
-
ST-24173
1
1
1
1
1
1
ED2-96 Series
Alto-Shaam
Part No.
Part Description
1.
CORD, (120/240V), 7' (2134mm)
CORD, (230V), 7' (2134mm)
PLUG ( COUNTERTOP UNITS (120/240V
2.
INSULATION
1/2" x 24" x 48" (13mm x 610mm x 1219mm)
3.
7.
FUSE HOLDER
FUSE, 15 AMP
8.
TERMINAL BLOCK, MODULAR
TERMINAL BLOCK
9.
TERMINAL BLOCK, SYS ONLY
ONLY )
ONLY
10. BULBS (120/240V)
BULBS (230V)
11. RECEPTACLE, BULB (120/240V)
RECEPTACLE, BULB (230V)
17. CUTTING BOARD ASSEMBLY, 4' (1219mm)
CUTTING BOARD BRACKET BASE
CUTTING BOARD BRACKET
GRID
INSERT, 2" DEEP (51mm) (PL/PR)
DIVIDER, LONG SEE PAGES 7, 8, 9
DIVIDER, SHORT SEE PAGES 7, 8, 9
20. GAS STRUT, 50# ( SELF - SERVE GLASS )
GAS STRUT, 195#
PIN, HINGE, ANCHOR
PIN, STRUT PIVOT
BUSHING, BEARING, NYLON
PLUG, WEAR
21. LEGS, 4" (102mm)
22. EQUIPOTENTIAL STUD (230V)
#868 • ED2 Series Operation & Care Manual • 18
#868 • ED2 Series Operation & Care Manual • 19
#868 • ED2 Series Operation & Care Manual • 20
#868 • ED2 Series Operation & Care Manual • 21
#868 • ED2 Series Operation & Care Manual • 22
#868 • ED2 Series Operation & Care Manual • 23
#868 • ED2 Series Operation & Care Manual • 24
#868 • ED2 Series Operation & Care Manual • 25
#868 • ED2 Series Operation & Care Manual • 26
#868 • ED2 Series Operation & Care Manual • 27
TRANSPORTATION
DAMAGE and CLAIMS
LIMITED
WARRANTY
All Alto-Shaam
equipment is sold
F.O.B. shipping point,
and when accepted by
the carrier, such
shipments become the
property of the consignee.
Should damage occur in shipment, it is a matter between
the carrier and the consignee. In such cases, the carrier is
assumed to be responsible for the safe delivery of the
merchandise, unless negligence can be established on the
part of the shipper.
1. Make an immediate inspection while the equipment is
still in the truck or immediately after it is moved to the
receiving area. Do not wait until after the material is
moved to a storage area.
2. Do not sign a delivery receipt or a freight bill until you
have made a proper count and inspection of all
merchandise received.
Alto-Shaam, Inc. warrants to the original purchaser that
any original part that is found to be defective in material or
workmanship will, at our option, subject to provisions
hereinafter stated, be replaced with a new or rebuilt part.
The labor warranty remains in effect one (1) year from
installation or fifteen (15) months from the shipping date,
whichever occurs first.
The parts warranty remains in effect one (1) year from
installation or fifteen (15) months from the shipping date,
whichever occurs first.
Exceptions to the one year part warranty period are as listed:
A. Halo Heat cook/hold ovens include a five (5) year parts
warranty on the heating element. Labor will be
covered under the terms of the standard warranty
period of one (1) year or fifteen (15) months.
B. Alto-Shaam Quickchillers include a five (5) year parts
warranty on the refrigeration compressor. Labor will
be covered under the terms of the standard warranty
period of one (1) year or fifteen (15) months.
This warranty does not apply to:
1.
Calibration.
3. Note all damage to packages directly on the carrier’s
delivery receipt.
2.
Replacement of light bulbs and/or the replacement of
display case glass due to damage of any kind.
4. Make certain the driver signs this receipt. If he refuses
to sign, make a notation of this refusal on the receipt.
3.
Equipment damage caused by accident, shipping,
improper installation or alteration.
4.
Equipment used under conditions of abuse, misuse,
carelessness or abnormal conditions.
5.
Any losses or damage resulting from malfunction,
including loss of product or consequential or incidental
damages of any kind.
6.
Equipment modified in any manner from original model,
substitution of parts other than factory authorized parts,
removal of any parts including legs, or addition of any parts.
5. If the driver refuses to allow inspection, write the
following on the delivery receipt:
Driver refuses to allow inspection
of containers for visible damage.
6. Telephone the carrier’s office immediately upon finding
damage and request an inspection. Mail a written
confirmation of the time, date, and the person called.
7. Save any packages and packing material for further
inspection by the carrier.
8. Promptly file a written claim with the carrier and attach
copies of all supporting paperwork.
We will continue our policy of assisting our customers in
collecting claims which have been properly filed and
actively pursued. We cannot, however, file any damage
claims for you, assume the responsibility of any claims, nor
accept deductions in payment for such claims.
This warranty is exclusive and is in lieu of all other warranties,
expressed or implied, including the implied warranties of
merchantability and fitness for purpose. In no event shall the
Company be liable for loss of use, loss of revenue, or loss of
product or profit, or for indirect or consequential damages. This
warranty is in lieu of all other warranties expressed or implied
and Alto-Shaam, Inc. neither assumes or authorizes any persons
to assume for it any other obligation or liability in connection
with Alto-Shaam equipment.
ALTO-SHAAM, INC.
Warranty effective January 1, 2000
RECORD THE MODEL AND SERIAL NUMBER OF THE UNIT FOR EASY REFERENCE.
ALWAYS REFER TO BOTH MODEL AND SERIAL NUMBER IN ANY CONTACT WITH ALTO-SHAAM REGARDING THE UNIT.
Model Number: _____________________________________
Voltage: ____________________________________________
Serial Number: ______________________________________
W164 N9221 Water Street
PHONE:
●
P.O. Box 450
262.251.3800
800.558.8744
FAX:
U.S.A./CANADA
●
Date Installed: _____________________________________
Purchased From: ____________________________________
____________________________________________________
Menomonee Falls, Wisconsin 53052-0450
262.251.7067
●
262.251.1907
INTERNATIONAL
800.329.8744
U.S.A./CANADA
●
U.S.A.
WEBSITE:
WWW.alto-shaam.com