FD Trinitron Colour Television KV-32LS60U KV

01CoverKV32LS60U.fm Page 1 Tuesday, May 14, 2002 10:52 AM
4-090-586-11(1)
R
FD Trinitron
Colour Television
Instruction Manual
KV-32LS60U
KV-28LS60U
© 2002 by Sony Corporation
GB
02p2KV32LS60U.fm Page 2 Tuesday, May 14, 2002 10:50 AM
NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM
A moulded plug complying with BS1363 is fitted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or
BSI to BS 1362 (i.e. marked with 2 or @) must be used.
When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the
circuit should be protected by a 5 AMP FUSE at the distribution board.
If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse
cover after you change the fuse. Never use the plug without the fuse cover. If you should lose
the fuse cover, please contact your nearest Sony service centre.
How to replace the fuse
Open the fuse compartment with a blade screwdriver, and replace the fuse.
•
IMPORTANT
If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and
an appropriate plug fitted in accordance with the following instructions:
The wires in this mains lead are coloured in accordance with the following code:
Blue
Neutral
Brown
Live
As the colours of the wires in the mains lead of this apparatus may not correspond with the
coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black. The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red. Do not connect either wire to the
earth terminal in the plug which is marked by the letter E or by the safety earth symbol
or coloured green or green and yellow.
WARNING
• To prevent shock hazard, do not insert the plug cut off from the mains lead into a socket
outlet. This plug cannot be used and should be destroyed.
• To prevent fire or shock hazard, do not expose the unit to rain or moisture.
• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing
to qualified personnel only.
2
03GBKV32LS60U.fm Page 3 Tuesday, May 14, 2002 10:48 AM
Introduction
Thank you for choosing this Sony FD Trinitron Colour Television.
Before operating the TV, please read this manual thoroughly and retain it for future
reference.
• Symbols used in the manual:
•
Important information
•
Information on a feature.
•1,2... Sequence of instructions.
•
•
OK
Shaded buttons on the remote control show
you the buttons you have to press to follow
the sequence of the instructions.
Informs you of the result of instructions.
Table of Contents
Notice for Customers in the United Kingdom .................................................................................... 2
Introduction.............................................................................................................................................. 3
Safety Information................................................................................................................................... 4
Overview
Overview of Remote Control Buttons .................................................................................................. 5
Overview of TV Buttons ........................................................................................................................ 6
Installation
GB
Inserting Batteries into the Remote Control ........................................................................................ 6
Connecting the Aerial and VCR ........................................................................................................... 6
First Time Operation
Switching On the TV and Automatically Tuning .............................................................................. 7
Menu system
Introducing and Using the Menu System............................................................................................ 9
Menu Guide:
Picture Adjustment ............................................................................................................................. 9
Sound Adjustment............................................................................................................................. 10
Sleep Timer......................................................................................................................................... 11
Language ............................................................................................................................................ 11
Auto Tuning ....................................................................................................................................... 11
Programme Sorting ........................................................................................................................... 12
Programme Labels............................................................................................................................. 12
AV Preset ............................................................................................................................................ 12
Manual Programme Preset............................................................................................................... 13
Noise Reduction................................................................................................................................. 14
Auto Format ....................................................................................................................................... 14
AV3 Output ........................................................................................................................................ 15
TV Speakers........................................................................................................................................ 15
RGB Centring ..................................................................................................................................... 15
Picture Rotation ................................................................................................................................. 16
Teletext ............................................................................................................................................... 17
Additional Information
Connecting Optional Equipment ........................................................................................................ 18
Using Optional Equipment .................................................................................................................. 19
Remote Control Configuration for VCR/DVD................................................................................. 20
Specifications.......................................................................................................................................... 21
Troubleshooting..................................................................................................................................... 22
Television Channel Guide for United Kingdom............................................................................... 23
Table of Contents
3
03GBKV32LS60U.fm Page 4 Tuesday, May 14, 2002 10:48 AM
Safety Information
For environmental and safety
reasons, it is recommended that
the TV set is not left in standby
mode when not in use. Disconnect
from the mains.
Do not open the cabinet and the rear
cover of the TV. Refer to qualified
service personnel only.
For your own safety, do not touch
any part of the TV, power lead or
aerial lead during lightning
storms.
Do not cover the ventilation
openings of the TV For
ventilation, leave a space of at
least 10cm all around the set.
Never place the TV in hot, humid To prevent fire, keep inflammable
objects or naked lights (eg
or excessively dusty places. Do
not install the TV where it may be candles) away from the TV.
exposed to mechanical vibrations.
Clean the TV with a soft, lightly
dampened cloth. Do not use
benzine, thinner or any other
chemicals to clean the TV. Do not
scratch the TV screen. As a safety
precaution, unplug the TV before
cleaning it.
Pull out the power lead by the
plug. Do not pull on the power
lead itself.
Place the TV on a secure stable
stand. Do not allow children to
climb on to it. Do not place the TV
on its side or face up.
4
Never push objects of any kind into
the set as this could result in a fire
or electric shock. Never spill liquid
of any kind on the set. If any liquid
or solid object does fall through, do
not operate the TV. Have it checked
immediately by qualified
personnel.
This set is to operate on a 220240V AC supply only. Take care
not to connect too many
appliances to the same power
socket as this could result in fire
or electric shock.
Safety Information
Unplug the power lead before
moving the TV. Avoid uneven
surfaces, quick steps or excessive
force. If the set has been dropped
or damaged, have it checked
immediately by qualified service
personnel.
To prevent fire or shock
hazard, do not expose the TV
to rain or moisture.
Take care not to place heavy
objects on the power lead as this
could result in damage.
We recommend you wind any
excess lead around the holders
provided on the rear of the TV.
Do not cover the ventilation
openings of the TV with items
such as curtains or newspapers
etc.
03GBKV32LS60U.fm Page 5 Tuesday, May 14, 2002 10:48 AM
Overview of Remote Control Buttons
!ª
1
2
3
!•
!¶
!§
!∞
4
5
6
7
8
!¢
!£
9
!º
!¡
1 To Temporarily Switch Off TV:
Press this button to temporarily switch off TV (the standby indicator
on
the TV lights up). Press again to switch on TV from standby mode.
To save energy we recommend switching off completely when TV is not in use.
After 15 minutes without a signal and without any button being
pressed, the TV switches automatically into standby mode.
2 Selecting input source: Press this button repeatedly until the desired
input symbol of the source appears on the TV screen.
3 Selecting channels:
If Media Selector is switched to TV or VCR, press this button to select
channels.
For double-digit programme numbers, enter the second digit within 2.5
seconds.
4 a) If Media Selector is switched to TV:
Press this button to watch the last channel selected (the last channel
watched for at least 5 seconds).
b) If Media Selector is switched to VCR:
For Sony’s VCR double-digit programme numbers, e.g. 23, press -/- first and then the buttons 2 and 3.
5 This button only works in Teletext mode.
!™
6 Selecting screen format: Press this button repeatedly to change the
format of the screen. For more details refer to chapter “Auto Format” on
page 14.
7 Selecting Teletext: Press this button to switch on teletext.
8 a) If Media Selector is switched to TV:
• When MENU is switched on, use these buttons to operate the menu
system. For details refer to “Introducing and Using the Menu System”
on page 9.
• When MENU is switched off, press OK to show a channel overview.
Then press
or
to select the channel and then press again the OK
button to watch the selected channel.
GB
b) If Media Selector is switched to VCR or DVD:
Using these buttons you can control the main functions of your VCR or
DVD.
9 Recording button: If Media Selector is switched to VCR, press this button to record programmes.
!º Media Selector:
With this remote control you can operate not only this TV but also the main functions of your VCR or DVD.
Switch on the device you want to operate and next press this button repeatedly to select the VCR, TV or
DVD. A green light will be momentarily lit to indicate the chosen function.
Before the first time you want to control a DVD or VCR by using this remote control, you have to set
it up depending on the brand of the device to be used. For more details, refer to chapter “Remote
Control Configuration for VCR or DVD” on page 20.
!¡ Selecting channels: Press this button to select the next or previous broadcast channel.
!™ Muting the Sound: Press this button to mute TV sound. Press again to restore the sound.
!£ Adjusting TV volume: Press this button to adjust the volume of the TV.
!¢ Displaying the menu system: Press this button to display the menu on the TV screen. Press again to
remove the menu display from the TV screen.
!∞ Selecting TV mode: Press this button to switch off teletext or video input.
!§ Selecting Sound effect: Press this button repeatedly to change the sound effect.
!¶ Selecting Picture mode: Press this button repeatedly to change the picture mode.
!• Displaying on Screen information: Press this button to display all on-screen indications. Press again
to cancel.
!ª VCR or DVD on/off: Press this button to switch your VCR or DVD on or off.
Besides TV functions, all coloured buttons as well as green symbols are also used for
Teletext operation. For more details, please refer to “Teletext” section of this instruction manual.
Overview
5
03GBKV32LS60U.fm Page 6 Tuesday, May 14, 2002 10:48 AM
Overview of TV Buttons
Programme Up or
Down Buttons (Selects
TV channels)
Volume control
buttons
Press on the
mark
on the
door flap to
reveal the
control panel.
Selecting
Input
source
Video
Input jack
Auto Start Up Button
S video Input jack
Audio
Input jacks
Standby
indicator
On/Off
switch
Headphones jack
Inserting Batteries into the Remote Control
Make sure you insert the supplied batteries using the correct polarities.
Always remember to dispose of used batteries in an environmental friendly way.
Connecting the Aerial and VCR
Connecting cables are not supplied.
or
VCR
OUT
IN
Scart lead is optional.
For more details of VCR connection, please refer to the section
“Connecting Optional Equipment” of this instruction manual.
6
Overview-Installation
03GBKV32LS60U.fm Page 7 Tuesday, May 14, 2002 10:48 AM
Switching On the TV and Automatically Tuning
The first time you switch on your TV, a sequence of menu screens appear on the TV
enabling you to: 1) choose the language of the menu screen, 2) adjust the picture slant,
3) search and store all available channels (TV Broadcast) and 4) change the order in which
the channels (TV Broadcast) appear on the screen.
However, if you need to change any of these settings at a later date, you can do that by
selecting the appropriate option in the
(Set Up menu) or by pressing the Auto Start Up
Button
on the TV set.
1 Connect the TV plug to the mains socket (220-240V AC,
50Hz)
The first time that the TV set is connected, it is usually
turned on. If the TV is off, press the
on/off button on
the TV set to turn on the TV.
The first time you switch on the TV, a Language menu
displays automatically on the TV screen.
GB
2 Press the
or
button on the remote control to select
the language, then press the OK button to confirm your
selection. From now on all the menus will appear in the
selected language.
Language
i4
Svenska
Norsk
English
Nederlands
Français
Italiano
i$
OK
Select Language:
3 Because of the earth’s magnetism, the picture might slant.
The Picture Rotation menu allows you to correct the
picture slant if it is necessary.
a)
If it is not necessary, press
necessary and press OK.
or
to select Not
OK
If picture slants, please
adjust picture rotation
Not necessary
Adjust now
OK
OK
b) If it is necessary, press
or
to select Adjust now,
then press OK and correct any slant of the picture
between –5 and +5 by pressing
or
. Finally press
OK to store.
continued...
First Time Operation
7
03GBKV32LS60U.fm Page 8 Tuesday, May 14, 2002 10:48 AM
4 The Auto Tuning menu appears on the screen. Press the
OK button to select Yes.
Do you want to start
automatic tuning?
Yes
No
OK
OK
5 The TV starts to automatically search and store all
available broadcast channels for you.
This procedure could take some minutes. Please be
patient and do not press any buttons, otherwise the
automatic tuning will not be completed.
Auto Tuning
Programme:
Channel:
01
C21
Searching...
In some countries the TV Broadcaster installs the
channels automatically (ACI system). In this case,
the TV Broadcaster sends a menu in which you can
select your city by pressing the
or
button and
OK to store the channels.
If no channels were found during the auto tuning
process then a new menu appears automatically on
the screen asking you to connect the aerial. Please
connect the aerial (see page 6) and press OK. The
auto tuning process will start again.
6
After all available channels are captured and stored,
the Programme Sorting menu appears automatically
on the screen enabling you to change the order in
which the channels appear on the screen.
a)
b)
If you wish to keep the broadcast channels in the
tuned order, go to step 7.
No channel found
Please connect aerial
OK
Confirm
OK
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
OK
Select channel:
Exit: MENU
OK
If you wish to store the channels in a different order:
1 Press the
or
button to select the programme
number with the channel (TV Broadcast) you wish
to rearrange, then press the
button.
2 Press the
or
button to select the new
programme number position for your selected
channel (TV Broadcast), then press
.
Programme Sorting
Programme:
01 TVE
02 TVE2
03 TV3
04 C33
05 C27
06 C58
OK
05
Select new position:
Exit: MENU
C27
OK
3 Repeat steps b)1 and b)2 if you wish to change
the order of the other channels.
7 Press the MENU button to remove the menu from the
screen.
Your TV is now ready for use
8
First Time Operation
MENU
03GBKV32LS60U.fm Page 9 Tuesday, May 14, 2002 10:48 AM
Introducing and Using the Menu System
Your TV uses an on-screen menu system to guide you through the operations. Use the
following buttons on the Remote Control to operate the menu system:
1 Press the MENU button to switch the first level menu on.
2 • To highlight the desired menu or option, press
• To enter to the selected menu or option, press
• To return to the last menu or option, press
MENU
or
.
/
/
.
.
• To alter settings of your selected option, press
OK
or
.
• To confirm and store your selection, press OK.
3 Press the MENU button to remove the menu from the screen.
MENU
GB
Menu Guide
Level 1
Level 2
Picture Adjustment
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Level 3 / Function
PICTURE ADJUSTMENT
The “Picture Adjustment” menu allows you to
alter the picture adjustments.
OK
To do this: after selecting the item you want to
alter press
, then press repeatedly
/
/
or
to adjust it and finally press OK to
store the new adjustment.
This menu also allows you to customise the
picture mode based on the programme you are
watching:
Live (for live broadcast programmes, DVD
and Digital Set Top Box receivers).
Personal (for individual settings).
Movie (for films).
• Brightness, Colour and Sharpness can only be altered if “Personal” mode is selected.
• Hue is only available for NTSC colour signal (e.g: USA video tapes).
• Select Reset and press OK to reset the picture to the factory preset levels.
continued...
Menu System
9
03GBKV32LS60U.fm Page 10 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
SOUND ADJUSTMENT
The “Sound Adjustment” menu allows you to
alter the sound adjustments.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Sound Adjustment
Effect: Natural
Treble
Bass
Balance
Reset
Dual Sound: Mono
Auto volume: On
To do this: after selecting the item you want to
alter, press
. Then press repeatedly
/
/
or
to adjust it and finally press OK
to store the new adjustment.
Sound Adjustment
Effect: Natural
Treble
Bass
Balance
Reset
Dual Sound: Mono
Auto volume: On
OK
OK
Enhances clarity, detail and presence of sound by
using “BBE High Definition Sound system”*.
Dynamic:
“BBE High Definition Sound system”* intensifies
clarity and presence of sound for better intelligibility
and musical realism.
Dolby**Virtual: Simulates the sound effect of “Dolby Surround Pro
Logic”.
Effect
Natural:
Off:
Flat response.
Treble
Less
More
Bass
Less
More
Balance
Left
Right
Reset
K
Dual Sound
Resets the sound to the factory preset levels.
•
•
Auto Volume
For a stereo broadcast:
Mono.
Stereo.
For a bilingual broadcast:
Mono (for mono channel if available).
A (for channel 1).
B (for channel 2).
Off: volume level changes according to the broadcast signal.
On: volume level of the channels will stay the same, independent of
the broadcast signal (e.g. in the case of advertisements).
• If you are listening to the TV through headphones, the “Effect” option will automatically be switched
to “Off”.
• If you select “Dolby Virtual” on the “Effect” option, the “Auto Volume” option will automatically be
switched to “Off” and vice versa.
* The “BBE High Definition Sound system” is manufactured by Sony Corporation under license
from BBE Sound, Inc. It is covered by U.S. Patent No. 4,638,258 and No. 4,482,866. The word
“BBE” and BBE Symbol are trademarks of BBE Sound, Inc.
**This TV has been designed to create the “Dolby Surround” sound effect by simulating the sound
of four speakers with two speakers, when the broadcast audio signal is Dolby Surround encoded.
The sound effect can also be improved by connecting a suitable external amplifier (for details refer
to “Connecting to external audio Equipment” on page 19).
**Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic” and the double-D
symbol
are trademarks of Dolby Laboratories.
continued...
10
Menu System
03GBKV32LS60U.fm Page 11 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
SLEEP TIMER
The “Sleep Timer” option in the “Timer” menu
allows you to select a time period for the TV to
switch itself automatically into the standby
mode.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Timer
Timer
Sleep Timer:
Off
Sleep Timer:
Off
OK
OK
OK
Set Up
• While watching the TV, you can press the
button on the remote control to display the
time remaining.
• One minute before the TV switches itself into
standby mode, the time remaining is displayed on
the TV screen automatically.
LANGUAGE
The “Language” option in the “Set Up” menu
allows you to select the language that the
menus are displayed in.
To do this: after selecting the option, press
and then proceed in the same way as in the step
2 of the section “Switching On the TV and
Automatically Tuning” on page 7.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
To do this: after selecting the option press ,
then press
or
to set the time period delay
(max. of 4 hours).
OK
OK
AUTO TUNING
The “Auto Tuning” option in the “Set Up”
menu allows you to automatically search for
and store all available TV channels.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
To do this: after selecting the option, press
and then proceed in the same way as in the
steps 4 and 5 of the section “Switching On the
TV and Automatically Tuning” on page 8.
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
OK
continued...
Menu System
11
GB
03GBKV32LS60U.fm Page 12 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
PROGRAMME SORTING
The “Programme Sorting” option in the “Set
Up” menu allows you to change the order in
which the channels (TV Broadcast) appear on
the screen.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
To do this: after selecting the option, press
and then proceed in the same way as in step 6 b)
of the section “Switching On the TV and
Automatically Tuning” on page 8.
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
OK
PROGRAMME LABELS
The “Programme Labels” option in the “Set
Up” menu allows you to name a channel using
up to five characters (letters or numbers).
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
OK
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
OK
To do this:
1 After selecting the option, press
, then
press
or
to select the programme
number with the channel you wish to name.
2 Press
. With the first element of the Label
column highlighted, press
or
to select
a letter or number (select “-“ for a blank), then
press
to confirm this character. Select the
other four characters in the same way. Finally
press OK to store.
AV PRESET
The “AV Preset” option in the “Set Up” menu
allows you to designate a name to the external
equipment you have connected to the input
sockets of this TV.
To do this:
1 After selecting the option, press
, then
press
or
to select the input source you
wish to name (AV1, AV2 and AV3 are for the
rear Scarts and AV4 for side connectors).
Then press .
2 A label automatically appears in the label
column:
a) If you want to use one of the 6 predefined
label (CABLE, GAME, CAM, DVD,
VIDEO or SAT), press
or
to select
the desired label and finally press OK to
store.
b) If you want to set a different label, select
Edit and press
. Then with the first
element highlighted, press
or
to
select a letter, number or “-“ for a blank,
then press
to confirm this character.
Select the other four characters in the same
way and finally press OK to store.
continued...
12
Menu System
03GBKV32LS60U.fm Page 13 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
MANUAL PROGRAMME PRESET
The “Manual Programme Preset” option in the
“Set Up” menu allows you to:
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
a) Preset channels or the VCR channel one by
OK
Set Up
one to the programme order of your choice.
To do this:
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
OK
OK
1 After selecting the ”Manual Programme
Preset” option, press
then with
Programme option highlighted press .
Press
or
to select on which
programme number you want to preset the
channel (for VCR, select programme number
“0”). Then press .
2 After selecting the Channel option, press
. Then press the number buttons to enter
directly the channel number of the TV Broadcast or the channel of the VCR signal. If you
do not know the channel number, press
or
to search for it. When you tune the
desired channel, press OK twice to store.
Repeat all the above steps to tune and store more channels.
b)
Label a channel using up to five characters.
To do this: Highlighting the Programme option, press the PROG +/- button to select the
programme number with the channel you wish to name. When the programme you want to
name appears on the screen, select the Label option and press . Next press
or
to
select a letter, number or “-“ for a blank. Press
to confirm this character. Select the other
four characters in the same way. After selecting all the characters, press OK twice to store.
c)
Fine tune the broadcast reception. Normally the automatic fine tuning (AFT) will give the
best possible picture, however you can manually fine tune the TV to obtain a better picture
reception in case the picture is distorted.
To do this: while watching the channel (TV Broadcast) you wish to fine tune, select the AFT
option and press . Next press
or
to adjust the fine tuning between -15 and +15.
Finally press OK twice to store.
d)
Skip any unwanted programme numbers when they are selected with the PROG +/buttons.
To do this: Highlighting the Programme option, press the PROG +/- button to select the
programme number you want to skip. When the programme you want to skip
appears on the screen, select the Skip option and press
. Next press
or
to select
Yes. Finally press OK twice to confirm and store.
To cancel this function afterwards, select “No” instead of “Yes” in the step above.
continued...
Menu System
13
GB
03GBKV32LS60U.fm Page 14 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
AUTO FORMAT
The “Auto Format” option in the “Detail Set
Up” menu allows you to automatically change
the aspect ratio of the screen.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Detail Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
On
Auto
TV
On
0
0
OK
OK
To do this: after selecting the option, press
.
Then press
or
to select On (if you wish
the TV set to automatically switch the screen
format according to the broadcast signal) or Off
(if you wish to keep your preference). Finally
press OK to store.
Even if you have selected “On” or “Off” in the “Auto Format” option,
you can always modify the format of the screen by pressing
repeatedly on the remote control to select one of the following formats:
Smart
Smart: Imitation of wide screen effect for 4:3 broadcast.
4:3:
Conventional 4:3 picture size, full picture information.
14:9:
Compromise between 4:3 and 16:9 picture size.
Zoom: Widescreen format for letterbox movies.
Wide:
4:3
14:9
For 16:9 broadcast. Full picture information.
In “Smart”, “Zoom” and “14:9” modes, parts of the top and bottom of
the screen are cut off. Press
or
to adjust the position of the
image on the screen (e.g. to read subtitles).
Zoom
Wide
NOISE REDUCTION
The “Noise Reduction” option in the “Detail Set
Up” menu allows you to automatically reduce
the picture noise visible in the broadcast signal.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
OK
On
Auto
TV
On
0
0
OK
To do this: after selecting the option, press
Then press
or
to select Auto. Finally
press OK to confirm and store.
.
To cancel this function afterwards, select “Off”
instead of “Auto” in the step above.
continued...
14
Menu System
03GBKV32LS60U.fm Page 15 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
On
Auto
TV
On
0
0
If your VCR supports Smartlink, this
procedure is not necessary.
OK
OK
AV3 OUTPUT
The “AV3 Output” option in the “Detail Set
Up” menu allows you to select the source to be
output from the Scart connector
3/ S 3 so
that you can record from this Scart any signal
coming from the TV or from an external
equipment connected to the Scart connectors
1/
1 or
2/
2 or side connectors
S 4 or
4 and
4.
To do this: after selecting the option, press
Then press
or
to select the desired
output signal: TV, AV1, AV2, AV4, YC4 or
AUTO.
.
If you select “AUTO”, the output signal will always be the same one that is displayed on
the screen.
If you have connected a decoder to the Scart
3/ S 3 or to a VCR connected to this
Scart, please remember to change back the “AV3 Output” to “AUTO” or “TV” for correct
unscrambling.
TV SPEAKERS
The “TV Speakers” option in the “Detail Set
Up” menu allows you to mute the TV speakers
in order to listen to the TV from an external
amplifier connected to the audio outputs on the
rear of the TV set.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Detail Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
On
Auto
TV
On
0
0
OK
OK
To do this: after selecting the option, press
Then press
or
to select Off. Finally
press OK to confirm and store.
.
To cancel this function afterwards, select “On”
instead of “Off” in the step above.
RGB CENTRING
When connecting an RGB source, such as a
“PlayStation”, you may need to readjust the
horizontal position of the picture. If this is the
case, you can readjust it through the “RGB Centring” option in the “Detail Set Up”.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
OK
On
Auto
TV
On
0
0
OK
To do this: while watching an RGB source select
the “RGB Centring” option and press
. Then
press
or
to adjust the centre of the
picture between –10 and +10. Finally press OK
to confirm and store.
continued...
Menu System
15
GB
03GBKV32LS60U.fm Page 16 Tuesday, May 14, 2002 10:48 AM
Level 1
Level 2
Level 3 / Function
PICTURE ROTATION
Because of the earth’s magnetism, the picture
might slant. If this is the case, you can correct
the pictures slant by using the “Picture
Rotation” option in the “Detail Set Up” menu.
Picture Adjustment
Mode: Personal
Contrast
Brightness
Colour
Sharpness
Hue
Reset
OK
Detail Set Up
Set Up
Language
Auto Tuning
Programme Sorting
Progamme Labels
AV Preset
Manual Programme Preset
Detail Set Up
Auto Format:
Noise Reduction:
AV3 Output:
TV Speakers:
RGB Centring:
Picture Rotation:
OK
16
Menu System
On
Auto
TV
On
0
0
OK
To do this: after selecting the option, press
.
Then press
or
to correct any slant of the
picture between -5 and +5.
03GBKV32LS60U.fm Page 17 Tuesday, May 14, 2002 10:48 AM
Teletext
Teletext is an information service transmitted by most TV stations. The index page of the
teletext service (usually page 100) gives you information on how to use the service. To
operate teletext, use the remote control buttons as indicated below.
Teletext errors may occur if you use a channel (TV Broadcast) with a weak signal.
To switch on Teletext :
After selecting the TV channel which carries the teletext service you wish
to view, press
.
TELETEXT
Index
Programme
News
Sport
Weather
25
153
101
98
To select a Teletext page:
Input 3 digits for the page number, using the numbered buttons.
• If you make a mistake, retype the correct page number.
• If the counter on the screen continues searching, it is because the page is not available. If this is the
case, input another page number
To access the next or preceding page:
Press PROG + (
) or PROG - (
).
To superimpose teletext on to the TV:
Whilst you are viewing teletext, press
GB
. Press it again to cancel teletext mode.
To freeze a teletext page:
Press
/
. Press it again to cancel the freeze.
To reveal concealed information (e.g: answer to a quiz):
Press
/
. Press it again to conceal the information.
To select a sub page:
A teletext page may consist of several sub pages. In this case the page number that appears
on the upper left corner will change from white to green and one or more arrows will appear
next to the page number. Repeatedly press the
or
buttons on the remote control to
watch the desired sub page.
To Switch Off Teletext:
Press
.
Fastext
Fastext service lets you access Teletext pages with one button push.
When you are in Teletext mode and Fastext is broadcast, a colour coded menu appears at
the bottom of the teletext page. Press the appropriate coloured button (red, green, yellow
or blue) to access the page corresponding to your menu choice.
Teletext
17
03GBKV32LS60U.fm Page 18 Tuesday, May 14, 2002 10:48 AM
Connecting Optional Equipment
Using the following instructions you can connect a wide range of optional equipment to
your TV set. (Connecting cables are not supplied).
S VHS/Hi8
DVC
camcorder
8mm/Hi8/
DVC
camcorder
G VCR
F
A
B
D
C
Decoder
E
DVD
Hi-fi
1
2
“PlayStation”*
When you connect the headphones,
the TV speakers will automatically
be muted.
* “PlayStation” is a product of Sony
Computer Entertainment, Inc.
* “PlayStation” is a trademark of Sony
Computer Entertainment, Inc.
Decoder
• To avoid picture distortion, do not connect external equipment to connectors A and B
at the same time.
• Do not connect a Decoder to the Scart F.
• Games that use a “gun” attachment to point at the screen do not work correctly due to
100 Hz technology used in this television.
Connecting a VCR:
To connect a VCR, please refer to the section “Connecting the aerial and VCR” of this instruction
manual. We recommend you connect your VCR using a scart lead. If you do not have a scart
lead, tune in the VCR test signal to the TV programme number “0” by using the “Manual
Programme Preset” option. (for details of how to manually programme these presets, see page
13, step a).
Refer to your VCR instruction manual to find out how to find the output channel of your VCR.
Connecting a VCR that supports Smartlink:
Smartlink is a direct link between the TV set and the VCR. For more information on
Smartlink, please refer to the instruction manual of your VCR.
If you use a VCR that supports Smartlink, please connect the VCR to the TV using a Scart
lead to the Scart
3/ S 3 G.
continued...
18
Additional Information
03GBKV32LS60U.fm Page 19 Tuesday, May 14, 2002 10:48 AM
Connecting to external Audio Equipment:
Plug in your Hi-Fi equipment to the audio output sockets D if you wish to amplify the audio
output from TV. Next , using the menu system, select the “Set Up” menu, enter the “Detail Set
Up” menu and set “TV Speakers” to “Off”.
Audio level of the external speakers can be modified by pressing the volume buttons on the
remote control. Also treble and bass settings can be modified through the “Sound
Adjustment” menu.
To enjoy “Dolby Virtual” sound effect through your
Hi-Fi equipment:
Place the speakers of your equipment in front of your
listening position and beside the TV set but keeping a
distance of 50 cm between each speaker and the TV set.
Then by using the menu system, select the menu “Sound
Adjustment”. Next select “Dolby Virtual” on the “Effect”
option.
Left Hi-Fi
speaker
Right Hi-Fi
speaker
~50°
Using Optional Equipment
1
Connect your equipment to the designated TV
socket, as indicated in the previous page.
2
3
Switch on the connected equipment.
To watch the picture of the connected equipment, press the
correct input symbol appears on the screen.
Symbol
S
S
4
Press
Your sitting position
GB
button repeatedly until the
Input Signals
1
1
• Audio / video input signal through the Scart connector E
• RGB input signal through the Scart connector E. This symbol appears only
if an RGB source has been connected.
2
2
• Audio / video input signal through the Scart connector F.
3
3
• Audio/video input signal through the Scart connector G.
4
• Video input signal through the phono socket B and Audio input signal
through C.
4
• S Video Input signal through the front S Video input jack A and Audio
signal through C. This symbol appears only if an S Video source has been
connected.
• RGB input signal through the Scart connector F. This symbol appears only
if an RGB source has been connected.
• S Video Input signal through the Scart connector G. This symbol appears
only if an S Video source has been connected.
button on the remote control to return to the normal TV picture.
For Mono Equipment
Connect the phono plug to the L/G/S/I socket on the front of the TV and select
4 or S 4
input signal using the instructions above. Finally, refer to the “Sound Adjustment” section of
this manual and select “Dual Sound” “A” on the sound menu screen.
Additional Information
19
03GBKV32LS60U.fm Page 20 Tuesday, May 14, 2002 10:48 AM
Remote Control Configuration for VCR/DVD
In it’s default condition this remote control will operate the basic functions of this Sony TV, Sony
DVDs and most Sony VCRs. To control VCRs and DVDs of other manufacturers (and some Sony
VCR models), please complete the following steps:
•Before you start, look up the 3 digit code for your brand of DVD or VCR from the list
below. On those brands that have more than one code, enter the first code number.
•Sony will endeavour to update the software according to market changes.
Therefore, please refer to the code table included with the remote control for
the latest code set.
1
Press the Media Selector button on the remote control repeatedly until the
required green light (VCR or DVD) is lit.
3
If Media Selector is on TV position, code numbers will not be stored.
2
2
Before the green light goes out, press and hold the yellow button for
approximately 6 seconds until the green light starts flashing.
3
Whilst the green light is flashing, enter all three digits of the code for your
brand of VCR or DVD using the number buttons on the remote control.
If your selected code is entered correctly, all three green lights will be lit
momentarily.
4
Turn on your VCR or DVD and check that the main functions work.
• If your device is not working or some of the functions do not work
please check that you entered the correct code set or try the next code
listed against the brand.
• Your brand codes may be lost if weak batteries are not replaced within
a few minutes. To reset your brand of DVD or VCR please repeat the
above steps. A small label is added inside the battery door to allow you
to record your brand codes.
• Not all brands are covered and not all models of every brand may be covered.
VCR Brand List
DVD Brand List
Brand
Code
Brand
Code
SONY (VHS)
SONY (BETA)
SONY (DV)
AIWA
AKAI
DAEWOO
GRUNDIG
HITACHI
JVC
301, 302, 303, 308, 309
303, 307, 310
304, 305, 306
325, 331, 351
326, 329, 330
342, 343
358, 355, 360, 361, 320, 351
327, 333, 334
314, 315, 322, 344, 352, 353,
354, 348, 349
332, 338
358, 355, 360, 361, 320, 351
356, 357
328
321, 323
311, 312, 313, 316, 317, 318,
358, 359
339, 340, 341, 345
335, 336
324
319, 350
337
SONY
AIWA
DENON
GRUNDIG
HITACHI
JVC
KENWOOD
LG
LOEWE
MATSUI
ONKYO
PANASONIC
PHILIPS
PIONEER
SAMSUNG
SANYO
SHARP
THOMSON
TOSHIBA
YAMAHA
001
021
018, 027, 020, 002
009, 028, 023, 024, 016, 003
025, 026, 015, 004
006, 017
008
015, 014
009, 028, 023, 024, 016, 003
013, 016
022
018, 027, 020, 002
009, 028, 023, 024, 016, 003
004
011, 014
007
019, 027
012
003
018, 027, 020, 002
LG
LOEWE
MATSUI
ORION
PANASONIC
PHILIPS
SAMSUNG
SANYO
SHARP
THOMSON
TOSHIBA
20
Additional Information
1
03GBKV32LS60U.fm Page 21 Tuesday, May 14, 2002 10:48 AM
Specifications
TV system:
I
Colour system:
PAL
SECAM, NTSC 3.58, 4.43 (only Video
In)
Channel Coverage:
I: UHF B21-B69
Picture Tube:
Flat Display FD Trinitron WIDE:
•KV-32LS60U: 32” (approx. 82 cm.
measured diagonally)
•KV-28LS60U: 28” (approx. 71 cm.
measured diagonally)
Rear Terminals
1/
1 21-pin scart connector
(CENELEC standard)
including audio/video
input, RGB input, TV
audio/video output.
2/
2 21-pin Scart connector
(CENELEC standard)
including audio / video
input, RGB input,
monitor audio/video
output.
3/
S
3 21-pin Scart connector
(SMARTLINK)
(CENELEC standard)
including audio / video
input, S video input,
selectable audio / video
output and Smartlink
interface.
audio outputs (Left/
Right) - phono jacks
Side Terminals
S 4
S Video input – 4 pin DIN
4 video input – phono jack
4 audio input – phono jacks
headphones jack
Sound Output:
2 x 20 W (music power)
2 x 10 W (RMS)
Woofer:
30 W (music power)
15 W (RMS)
Power Consumption:
KV-32LS60U: 130 W
KV-28LS60U: 125 W
Standby Power Consumption:
0.3 W
GB
Dimensions (w x h x d) :
KV-32LS60U: approx. 892 x 565 x 584 mm.
KV-28LS60U: approx. 806 x 497 x 540 mm.
Weight:
KV-32LS60U: approx. 62.2 Kg.
KV-28LS60U: approx. 45.4 Kg.
Accessories supplied:
1 Remote Control (RM-932)
2 Batteries (IEC designated)
Other features:
• 100 Hz picture
• Teletext, Fastext, TOPtext (250 page TEXT
memory)
• Sleep Timer
• Smartlink (direct link between your TV set
and a compatible VCR. For more
information on Smartlink, please refer to
the Instruction Manual of your VCR).
• Dolby Virtual.
• BBE.
• Auto Format.
• ACI (Auto Channel Installation).
Design and specifications are subject to change without notice.
Ecological Paper - Totally Chlorine Free
Additional Information
21
03GBKV32LS60U.fm Page 22 Tuesday, May 14, 2002 10:48 AM
Troubleshooting
Here are some simple solutions to problems which may affect the picture and sound.
Problem
Solution
No picture (screen is dark) and no
sound.
• Check the aerial connection.
• Plug the TV in and press the
button on the front of
the TV.
• If the standby indicator
is on, press TV
button on
the remote control.
Poor or no picture (screen is dark), but
good sound.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to the
factory settings.
• Check that the optional equipment is on and press the
No picture or no menu information
button repeatedly on the remote control until the
from equipment connected to the Scart
correct input symbol is displayed on the screen.
connector.
Good picture, no sound.
• Press the
+ button on the remote control.
• Check that “TV Speakers” is “On” in the “Detail Set Up”
menu.
• Check that headphones are not connected.
No colour on colour programmes.
• Using the menu system, select the “Picture
Adjustment” menu and select “Reset” to return to
factory settings.
Distorted picture when changing
programmes or selecting teletext.
• Turn off any equipment connected to the Scart
connector on the rear of the TV.
Picture slanted
• Using the menu system, select the “Picture Rotation”
option in the “Detail Set Up” menu to correct the
picture slant.
Noisy picture when viewing a TV
channel.
• Using the menu system, select the “Manual
Programme Preset” menu and adjust Fine Tuning
(AFT) to obtain better picture reception.
• Using the menu system, select the “Noise Reduction”
option in the “Detail Set Up” menu and select
“Auto” to reduce the noise in the picture.
No unscrambling or unstable picture
whilst viewing a scrambled channel
with a decoder connected through the
3/ S 3.
Scart connector
• Using the menu system, select the “Set Up” menu. Then
enter to “Detail Set Up” option and set “AV3 Output” to
“TV”.
Remote control does not function.
• Check that the Media Selector on the remote control is set
to the device you are using (VCR, TV or DVD).
• If the remote control does not operate the VCR or DVD
even when the Media Selector has been set correctly. Enter
the necessary code set as explained on “Remote Control
Configuration for VCR/DVD” chapter of this instruction
manual.
• Replace the batteries.
The standby indicator
flashes.
• Contact your nearest Sony service centre.
on the TV
If you continue to experience problems, have your TV serviced by qualified personnel.
Never open the casing yourself.
22
Additional Information
03GBKV32LS60U.fm Page 23 Tuesday, May 14, 2002 10:48 AM
Television Channel Number Guide for United Kingdom
Only the main transmitters are listed. Information regarding the regional sub-relay
channel numbers can be obtained by contacting The BBC Engineering Information Dept.,
Telephone Number 020 7852 5040.
GB
Additional Information
23
04B.cover.fm Page 1 Tuesday, May 14, 2002 10:48 AM
http://www.world.sony.com/
Printed in UK
Ecological Paper - Totally Chlorine Free