MX4X-6XXX Series MX4X-7XXX Series - iPortal

MX4X-6XXX Series
MX4X-7XXX Series
SmartX Actuators
and Accessories
Selection Guide
Applications
Direct-coupled SmartX Actuators are designed to
accept two-position, floating, or proportional control
from a DDC system or from a thermostat, for control of
HVAC applications. The actuators are designed to be
used in both damper and valve control applications.
Typical applications include air handling units, unit
ventilators, fan coil units, VAV terminals, control
dampers, inlet guide vanes, and linked valve
assemblies.
Use the following guide to select actuators for damper
applications. Refer to the Applicable Literature table for
valve literature.
MX41-6043
MX41-6083
MX40-704X
MX41-707X
MX41-715X
MX41-634X
MX40-717X
MX41-6153
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Applicable Literature
F-Number
Description
Audience
Purpose
F-27211
MF41-6043/MS41-6043 Series,
MF41-6083/ MS41-6083 Series Non-Spring Return
Direct Coupled Actuator Installation Instructions
F-27212
MF41-6153, MS41-6153 Non-Spring Return Direct
Coupled Actuator Installation Instructions
F-27213
MF41-6043/MF41-6083 Series Non-Spring Return
Rotary 24 Vac Three-Position Control Electronic Damper
Actuators General Instructions
F-27214
MS41-6043/MS41-6083 Series Non-Spring Return
Rotary 24 Vac Modulating Control 0 to 10 Vdc Electronic
Damper Actuators General Instructions
F-27215
MF41-6153/MS41-6153 Series Non-Spring Return
Rotary Electronic Damper Actuators General Instructions
F‑26744
MF41-6343 SmartX Series Non-Spring Return Direct
Coupled Actuator General Instructions
F‑26745
MS41-634X SmartX Series Non-Spring Return Direct
Coupled Actuator General Instructions
F‑26742
MA40-717X SmartX Series Spring Return Direct
Coupled Actuator General Instructions
F‑26748
MS40-717X SmartX Series Spring Return Direct
Coupled Actuator General Instructions
F‑26749
MF40-7173 SmartX Series Spring Return Direct Coupled
Actuator General instructions
F‑26644
MF4X-7XX3, MF4X-7XX3-50X Schneider Electric
SmartX Series Spring Return Direct Coupled Actuator
General Instructions
F‑26642
MA4X-7XX3, MA4X-7XX3-50X, MA4X-7XXX, MA4X7XXX-50X SmartX Series Spring Return Direct Coupled
Actuator General Instructions
F‑26645
MS4X-7XX3, MS4X-7XX3-50X SmartX Series Spring
Return Direct Coupled Actuator General Instructions
F-27160
MX4X-6XXX-220/-230 and MX4X-7XXX-220 Actuator/
Linkage Assemblies for 2-1/2” to 6” Globe Valves
General Instructions
Describes the valve assemblies’ features,
specifications, and possible applications.
Provides step-by-step mounting,
installation, and checkout instructions.
F-26750
MA4X-XXXX-2XX, MF4X-XXXX-2XX, MS4X-XXXX-2XX
Series Actuator/Linkage Assemblies for 1/2” to 2” Globe
Valves General Instructions
Describes the globe valve actuator/linkage
assembly’s features, specifications, and
possible applications. Provides step-bystep mounting instructions.
F-27087
VX-2X13-5XX-9-XX Series, VB-2X13-500-9-XX Series
Ball Valve Assemblies and Ball Valve Body/Linkage
Assemblies Installation Instructions
Describes the actuator/linkage/ball valve
assemblies’ features, specifications, and
possible applications. Provides step-bystep mounting instructions.
F-26752
VX-7000 and VX-9000 Series, MX4X-6XXX and
MX4X-7XXX Series, Linked Globe Valve Assemblies and
Actuator/Linkage Assemblies with SmartX Actuators
Selection Guide
Provides features, specifications,
mounting dimensions, and other criteria
useful to the selection of linked globe valve
assemblies and actuator/linkage
assemblies with SmartX actuators.
F-27086
VX-2X13-5XX-9-XX Series Ball Valve Assemblies and
VB-2X13-500-9-XX Series Ball Valve Body/Linkage
Assemblies Selection Guide.
Provides features, specifications,
mounting dimensions, and other criteria
useful to the selection of linked ball valve
assemblies with SmartX actuators.
F-27216
MF41/MS41-6043 Series 24 Vac, 35 lb‑in. Non-Spring
Return, Direct-Coupled Electronic Damper Actuators
Submittal Sheet
Schneider Electric F-26646-9
Describes the actuator’s features,
specifications, and possible applications.
Provides step-by-step mounting
instructions.
– Sales Personnel
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
– Sales Personnel
– Application Engineers
Describes features and specifications of
the MX41-6043 series actuators.
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
F-Number
Description
Audience
Purpose
F-27217
MF41/MS41-6083 Series 24 Vac, 70 lb-in., Non-Spring
Return Direct-Coupled Electronic Damper Actuators
Submittal Sheet
– Sales Personnel
– Application Engineers
Describes features and specifications of
the MX41-6083 series actuators.
F-27218
MF41/MS41-6153 Series, 24 Vac, 133 lb‑in., Non-Spring
– Sales Personnel
Return, Direct-Coupled Electronic Damper Actuators
– Application Engineers
Submittal Sheet
Describes features and specifications of
the MX41-6153 series actuators.
F-26785
VX-2000, VX-7000, VB-2000, MX4X-7XXX, and
MX40-6XXX Series Ball and Globe Linked Valve
Assemblies, Valve/Linkage Assemblies, and Actuator/
Linkage Assemblies Cross-Reference Guide
Provides part number cross referencing of
phased-out devices with the new Actuator/
Linkage Assemblies, and Ball and Globe
LInked Valve Assemblies.
F-11080
Valve Selection Chart Water
F-11366
Valve Selection Chart Steam (two-way valves only)
F-13755
CA-28 Control Valve Sizing
F-26080
EN-205 Water System Guidelines
– Sales Personnel
– Application Engineers
– Application Engineers
– Installers
– Service Personnel
– Start-up Technicians
Provides charts, equations, and diagrams
to assist in the configuration of valve
system applications. TOOL-150, valve
sizing slide rule may be purchased
separately.
Describes Schneider Electric approved
water treatment practices.
Product Warranty
SmartX actuators are covered by a five year warranty.
Using this Selection Guide
This selection guide contains the following sections:
Actuator Part Numbering System
This section explains the SmartX actuator part numbering system.
Actuator Selection Chart
Use this chart as a quick reference guide. Refer to Actuator Selection section for specifications data, as well as
mounting dimensions.
Actuator Accessories Chart
Use this section to choose the appropriate accessories for the selected actuator.
Actuator Specifications and Mounting Dimensions
Use this section to choose the appropriate actuator for the application. This section includes actuator specifications
data, as well as mounting dimensions.
Damper Actuator Cross-Reference
Refer to this section for actuator replacement data.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Part Numbering System
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
SmartX Actuator Selection Chart
Spring-Return Actuators
Table-1 MX40-704X, MX4X-707X, and MX4X-715X Series Spring-Return Actuators.
Power Input
Actuator
Type
Part Numbers
Running
Voltage
MA40-7043
MA40-7043-501
TwoPosition
MA40-7040
MA40-7040-501
MA40-7041
MA40-7041-501
Floating
MF40-7043
MF40-7043-501c
MS40-7043
Proportional
c
MS40-7043-501c
MS40-7043-MP
MS40-7043-MP5
MA41-7073
MA41-7073-502d
TwoPosition
(page 17)
50 Hz
60 Hz
VA
W
VA
W
24 Vac ± 20%
22-30 Vdc
4.4
2.9
4.4
2.9
120 Vac ± 10%
6.4
3.8
4.3
230 Vac ± 10%
5.8
4.1
4.6
Holding
DC Amps
50 Hz 60 Hz
W
W
0.11
0.8
0.8
3.4
—
1.6
1.2
3.9
—
1.5
1.2
24 Vac ± 20%
22-30 Vdc
5.9
4.4
5.9
4.4
0.17
2.9
2.9
24 Vac ± 20%
22-30 Vdc
5.6
4.2
5.6
4.2
0.15
2.4
2.4
6.6 5.0 6.6 5.0
0.17
3.2
3.2
4.8
0.13
0.8
0.8
24 Vac
22-30 Vd
24 Vac ± 20%
22-30 Vdc
4.8
3.2
3.6
—
2.0
<26
<50
<26
35 (4)
150
(17)
60 (7)
250
(28)
Oneb
No
Oneb
<130
<25
<80
<40
No
Oneb
No
8.0
4.0
—
2.7
1.4
Twoe
MA41-7071-502d
MS41-7073-502d
<50
Max.
Stall
Twoe
(page 19) 230 Vac ± 10% 17.0 5.1
Proportional
<26
No
1.2
MA41-7071d
MS41-7073d
No
Oneb
<50
Min.
No
5.6
MA41-7070-502d
MF41-7073-502d
No
Oneb
Spring
Return
Two
120 Vac ± 10% 10.7 4.2
Floating
No
One
Powered
No
3.2
MA41-7070d
MF41-7073d
SPDT
Auxiliary
Switches
Approximate Timing in
Output Torque
Seconds @ 70 °F
Rating
(21 °C)
lb.-in. (N-m)
with No Load
No
24 Vac ± 20%
22-30 Vdc
6.2
24 Vac ± 20%
22-30 Vdc
5.8
4.8
6.2
4.8
0.18
2.8
2.8
<195
<30
<195
<30
Twoe
No
4.6
5.8
4.6
0.17
2.3
2.3
Twoe
a
De-rating required for spring return actuators at low temperatures.
One adjustable from 15 to 95° rotation (MIN to 1 scale).
c
With plenum-rated cable.
d
Equipped with manual override.
e
One adjustable from 25° to 85° rotation and one set to operate @ 5° fixed.
b
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Table-1 MX40-704X, MX4X-707X, and MX4X-715X Series Spring-Return Actuators.
Power Input
Actuator
Type
Part Numbers
Running
50 Hz
Voltage
MA41-7153d
24 Vac ± 20%
22-30 Vdc
MA41-7153-502d
60 Hz
VA
W
VA
W
9.8
7.5
9.7
7.5
SPDT
Auxiliary
Switches
Holding
DC Amps
50 Hz 60 Hz
W
W
2.8
2.8
Powered
Spring
Return
Min.a
Max.
Stall
<190
<30
133 (15)
350
(40)
No
0.29
Twoe
No
MA41-7150d
120 Vac ± 10% 11.7 8.8 10.0 8.4
Two-Position
—
3.6
5.0
Twoe
MA41-7150-502d
No
MA41-7151d
(page 21) 230 Vac ± 10% 15.5 9.5 10.6 8.5
MA41-7151-502
Approximate Timing in
Output Torque
Seconds @ 70 °F
Rating
(21 °C)
lb.-in. (N-m)
with No Load
—
4.6
3.3
Two
d
e
MF41-7153d
Floating
MF41-7153-502d
MS41-7153d
Proportional
MS41-7153-502d
No
24 Vac ± 20%
22-30 Vdc
9.8
24 Vac ± 20%
22-30 Vdc
9.8
7.7
9.7
7.7
0.30
3.3
3.3
Twoe
No
7.4
9.7
7.4
0.28
2.9
2.9
Twoe
De-rating required for spring return actuators at low temperatures.
One adjustable from 15 to 95° rotation (MIN to 1 scale).
c
With plenum-rated cable.
d
Equipped with manual override.
e
One adjustable from 25° to 85° rotation and one set to operate @ 5° fixed.
a
b
Table-2 MX40-717X Series Spring-Return Actuators.
Power Input @ 50/60 Hz
Part Numbers
MA40-7173
SPDT
Auxiliary
Switches
VA
Voltage
Running
Watts
Running
Holding
24 Vac ± 20%
5.3
7.4
5.1
22-30 Vdc
5.0
5.0
3.0
No
120 Vac ± 10%
6.2
8.4
6.6
No
MA40-7171
240 Vac ± 10%
6.5
9.8
8.5
No
24 Vac ± 20%
5.8
8.1
5.3
No
22-30 Vdc
5.7
5.7
3.6
No
(page 23)
24 Vac ± 20%
5.5
7.8
4.7
No
22-30 Vdc
5.0
5.6
2.5
No
MS40-7170
120 Vac ± 10%
6.4
8.5
5.2
No
MS40-7171
240 Vac ± 10%
7.2
10.8
9.0
No
MS40-7173
Powered
Spring
Return
162
72
Output Torque
Rating
lb.-in. (N-m)
Min.a
Max. Stall
150 (17)
545 (61.8)
No
MA40-7170
MF40-7173
Approximate Timing in
Seconds @ 70 °F (21 °C)
with No Load
147
65
De-rating required for spring return actuators at low temperatures.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Non-Spring Return Actuators
Table-3 Non-Spring Return Actuators.
Power Input @ 50/60 Hz
Part Numbers
Voltage
Watts
MF41-6043
Holding
No
2.0
2.3
—
b
2.0
2.3
—
2
MF41-6043-510b
2.0
2.3
—
No
3.0
3.3
1.2
No
MS41-6043-502bc
3.0
3.3
1.2
2
MS41-6043-520b
3.0
3.3
1.2
No
MS41-6043-522
3.0
3.3
1.2
2
2.0
2.3
—
No
2.0
2.3
—
2
2.0
2.3
—
No
3.0
3.3
1.2
No
bc
3.0
3.3
1.2
No
MS41-6083-520be
3.0
3.3
1.2
No
MS41-6083-522bf
3.0
3.3
1.2
2
MF41-6043-502
MS41-6043b
24 Vac +20/-15%
b
MF41-6083b
MF41-6083-502bc
MF41-6083-510
b
MS41-6083b
24 Vac +20/-15%
MS41-6083-502
MF41-6153
3.0
3.0
—
No
4.0
5.0
1.2
No
24 Vac ± 20%
3.9
5.7
4.1
22-30 Vdc
4.1
4.1
3.0
24 Vac ± 20%
3.6
5.6
4.0
22-30 Vdc
3.4
3.4
2.2
MS41-6340
120 Vac ±10%
4.7
7.5
6.2
MS41-6341
240 Vac ±10%
5.0
9.0
8.1
MS41-6153
MF41-6343
MS41-6343
a
Running
SPDT
Auxiliary
Switchesa
VA
24 Vac +20/-15%
Approximate Timing
in Seconds
@ 70 °F (21 °C)
with No Load
90 @ 60 Hz
108 @ 50 Hz
125 @ 60 Hz
Actuator Output
Torque Rating
(Minimum)
lb.-in. (N-m)
35 (4)
70 (8)g
150 @ 50 Hz
133 (15)h
No
162
No
148
300 (34)
Auxiliary switch ratings are as follows:
Auxiliary Switch Ratings
AC Rating
DC Rating
MX41-6043, MX41-6083
MX41-6153
24 Vac, 4 A resistive, 2 A inductive
24 Vac, 6 A resistive, 2 A inductive
12 to 30 Vdc, DC 2 A
Equipped with plenum-rated cable.
Equipped with two built-in auxiliary switches.
d
Equipped with 1k W feedback potentiometer.
e
Equipped with adjustable start/span.
f
Equipped with adjustable start/span and two auxiliary switches.
g
Minimum voltage at high temperatures: 24 Vac, +20%, -10% at 90 to 130 °F ambient.
h
Minimum voltage at high temperatures: 24 Vac, +20%, -5% (MF models) and 24 Vac, +20%, -10%
(MS models) at 85 to 130 °F ambient.
b
c
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Accessories Chart
AM-672
AM-671
AM-673
AM-620
AM-621
AM-676
AM-686
AM-674
AM-675
AM-690
AM-691
AM-692
AM-689
MF41-6153
MS41-6153
MF41-6343
MS41-634X Series
X
X
X
X
X
-
AM-621
Round Shaft
Extension
X
X
X
X
X
X
X
X
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
AM-675
Weather
Shield &
Base
X
X
X
X
X
X
AM-676
Shaft Extension
X
X
X
X
X
X
AM-686
Position Indicator
X
X
X
X
AM-687
V-clamp
X
X
X
X
AM-688
Replacement
Universal Clamp
X
X
X
X
AM-689
Rotation Limiter
X
X
X
X
X
abcd
AM-672
AM-673c
AM-674
e
AM-690
AM-691
Mounting
Bracket
Crank Arm
X
X
X
X
X
X
X
AM-692f
V-bolt
X
X
X
X
AM-693gh
Crank Arm
Kit
X
X
X
X
MS41-6083
MS40-717x Series
X
MF41-6083
MA40-717X Series
MF40-7173
X
MF41-6043
MS41-6043
MS4X-7153
X
MS4X-7073 Series
Actuator Remote
Mount
MS40-7043
AM-620
MA40-704X Series
MF40-7043
Description
MA4X-715X Series
MF4X-7153 Series
Non-Spring Return Actuators
Part
Numbers
AM-671abcd
MA4X-707X Series
MF4X-7073 Series
Spring Return Actuators
AM-693
General Instructions
Document
AM-687
AM-688
F-25096
X
X
X
X
X
X
X
X
F-25097
F-25098
AM-693 crank arm kit required.
Cannot be used with MX41-634X or MX40-717X series actuators.
c
Drill appropriate mounting holes where needed.
d
The large “C”-shaped clamps included in AM-693 crank arm kit are required for mounting the actuator. Drill appropriate mounting holes where needed.
e
For shafts to 1.05” diameter or 5/8” square.
f
For shafts to 3/4” and 1.05” diameter (with AM-690 and AM-691, respectively).
g
Use the self-tapping screws and flat washers provided in kit to mount actuator.
h
AM-692 V-bolt kit required.
a
b
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
AM-708
AM-703
AM-706
AM-704
AM-712
AM-710, AM-717
AM-705
AM-709
AM-711
AM-713
AM-715
AM-714
AM-751
AM-728
MS41-634X Series
MF41-6343
MS41-6153
MF41-6153
MS41-6083
MS41-6043
MF41-6043
MS40-7173
MA40-717X Series
MF40-7173
MS4X-7153 Series
MA4X-715X Series
MF4X-7153 Series
MS4X-7073 Series
MA4X-707X Series
MF4X-7073 Series
AM-703
Span Adjustment
X
X
X
X
X
X
X
Modulation Interface
X
X
X
X
X
X
X
AM-705
Positioner
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
AM-708
500 W Resistor
AM-709
Position Indicator
& Stroke Limiter
X
X
AM-710
F-26895
F-26895
V-clamp
X
X
X
X
AM-712
Crank Arm
Adaptor Kit
X
X
AM-713
Bracket
X
X
AM-714
Weather Shield
X
X
AM-715
Crank Arm
Adaptor Kit
X
X
F-26896
AM-717
Replacement
Universal Clamp
X
X
F-26896
a
AM-711
AM-726
AM-727
AM-728b
AM-751
AM-752
b
Non-Spring Return Actuators
AM-704
AM-706
a
Description
MS40-7043
Part
Numbers
MA40-704X Series
MF40-7043
Spring Return Actuators
AM-752
General Instructions
Document
AM-727
MF41-6083
AM-726
F-26896
X
X
X
X
F-25097
Crank Arm Adaptor
Conduit Adaptor
Anti-rotation Bracket
X
X
X
X
X
X
X
X
X
X
X
X
F-26802
X
X
X
X
X
X
X
X
F-26898
For shafts up to 3/4” diameter round or up to 1/2” square.
Cannot be used when creating a linked valve/actuator assembly.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
AM-735
AM-737
AM-740
AM-736
AM-741
AM-753
AM-754
AM-761
AM-762
AM-756
MS41-634X Series
MS41-6153
Crank Arm Kit
X
X
F-27246
AM-736
Crank Arm Kit
with Bracket
X
X
F-27247
AM-737
Universal
Crank Arma
X
X
F-27248
AM-740
Replacement Kit
X
X
F-27249
AM-741
Weather Shield
X
X
X
Mounting Clamp
AM-755
Manual Override
Crank
AM-756
Metric Conduit
Adaptor
AM-758
X
X
X
X
Short “U” Mounting
Bracket
X
X
X
X
AM-759
Tall “U” Mounting
Bracket
X
X
X
X
AM-760
Slotted “L” Mounting
Bracket
X
X
X
X
AM-761
7-inch Anti-Rotation
Bracket
X
X
AM-762
9-inch Anti-Rotation
Bracket
X
X
AM-763
Manual Override
Crank
TF-711-02
X
X
X
X
MF41-6343
MF41-6153
AM-735
MF41-6083
Description
AM-754c
MF41-6043
MS41-6043
Part
Numbers
AM-753b
MS40-7173
Non-Spring Return Actuators
MA40-717X Series
MF40-7173
MS4X-7153 Series
MA4X-715X Series
MF4X-7153 Series
MS4X-7073 Series
MA4X-707X Series
MF4X-7073 Series
MS40-7043
MA40-704X Series
MF40-7043
Spring Return Actuators
General Instructions
Document
AM-760
AM-759
AM-758
MS41-6083
AM-755
AM-763
F-27250
X
X
X
X
X
X
X
X
X
X
X
X
X
X
F-26898
F-26899
F-25096
F-26986
X
X
X
X
Xd
Xd
Xd
Xd
X
X
X
X
F-25098
F-25098
Sealtight Conduit
Connector
X
X
X
X
—
TF-713-02
X
X
X
X
—
TF-5521
Pipe Plug
X
X
X
X
—
For Honeywell Floor Mount Mod Motor.
b
For shafts 3/4” round and 5/8” square.
c
For shafts 3/8” to 1/2” round and square.
d
Only used on MX41-707X-XXX, MX41-715X-XXX.
a
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications and Mounting Dimensions
MF41-6043 and MS41-6043 Actuators
For non-spring return applications requiring floating or proportional
modulation control of dampers and valves in HVAC systems.
Features:
•
•
•
•
•
•
•
Direct mount to round, square, or hexagonal damper shaft
Rated at 44 lb-in. (5 N-m) torque, minimum
Does not require any limit switches
Manual override allows positioning for installation and manual operation
MF41-6043 provides floating point control (3-position)
MS41-6043 provides proportional control compatible with 0 to 10 Vdc
5-year warranty
Actuator Specifications
Inputs
Control Signal
MF41-6043 — Floating three-position control, 24 Vac.
MS41-6043 — Proportional, 0 to 10 Vdc; input resistance 100 kW.
Power Requirements
All 24 Vac circuits are Class 2.
Part Numbers
Connections
Motor Type
Power Input @ 50/60 Hz
Voltage
Running VA
Holding VA
Watts
MF41-6043
24 Vac +20/-15%
2.3
—
2.0
MS41-6043
24 Vac +20/-15%
3.3
1.2
3.0
3 ft. (0.9 m) long, 18 AWG leads, plenum-rated.
Synchronous
Outputs
Electrical
AC Rating: 24 Vac, 4 A resistive, 2 A inductive
DC Rating: 12 to 30 Vdc, DC 2 A
Timing: 90 sec. at 60 Hz, 108 sec. at 50 Hz
Mechanical
Output torque rating: 44 lb‑in. (5 N‑m).
Stroke: Normal angle of rotation is 90°, limited to a maximum of 95°. Field adjustable to limit
travel on either end of stroke. Set for 5° preload at the factory.
Position indicator: Adjustable pointer is provided for position indication. See the Note in
“Switch Range.”
Output shaft setscrew: tightening torque 55 to 60 lb-in. (6.3 to 6.8 N-m).
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications
Environment
Temperature Limits
Shipping and storage: ‑40 to 158 °F (‑40 to 70 °C) ambient.
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA Type 2.
Operating: -25 to 130 °F (‑32 to 55 °C) ambient.
Agency Listings
UL
UL‑873, Underwriters Laboratories.
European Community
EMC Directive (89/336/EEC). Emissions (EN50081-1). Immunity (EN50081-2).
cUL
Canadian Standards C22.2 No. 24-93.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Accessories
AM-726
Rotary-to-Linear Bracket
AM-727
Rotary-to-Linear Crank Arm
AM-728
Conduit Adapter
AM-741
Weather Shield Kit
Figure-1 MF41-6043 and MS41-6043 Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MF41-6083 and MS41-6083 Actuators
For non-spring return applications requiring floating or proportional
modulation control of dampers and valves in HVAC systems.
Features:
•
•
•
•
•
•
•
Direct mount to round, square, or hexagonal damper shaft
Rated at 88 lb-in. (10 N-m) torque, minimum
Does not require any limit switches
Manual override allows positioning for installation and manual operation
MF41-6083 provides floating point control (3-position)
MS41-6083 provides proportional control compatible with 0 to 10 Vdc
Models available with: independently adjustable dual auxiliary switches;
adjustable start point (offset) and span
• 5-year warranty
Actuator Specifications
Inputs
Control Signal
MF41-6083 — Floating three-position control, 24 Vac.
MS41-6083 — Proportional, 0 to 10 Vdc; input resistance 100 kW.
Control signal adjustment available with MS41-6083-520 and MS41-6083-522:
Start point (offset) — Between 0 and 5 Vdc (factory setting = 0 Vdc)
Span — 2 to 30 Vdc
Power Requirements
All 24 Vac circuits are Class 2.
Power Input @ 50/60 Hz
Part Numbers
Connections
Motor Type
Voltage
Running VA
Holding VA
Watts
MF41-6083
24 Vac +20/-15%
2.3
—
2.0
MS41-6083
24 Vac +20/-15%
3.3
1.2
3.0
3 ft. (0.9 m) long, 18 AWG leads, plenum-rated.
Synchronous
Outputs
Electrical
Position output signal — Feedback potentiometer available with MF41-6083-510:
0 to 1000W < 10 mA
Output voltage: 0 to 10 Vdc
Maximum output current: 1 mA
Dual auxiliary switches available with MF41-6083-502, MS41-6083-502, MF41-6083-522,
and MS41-6083-522.
AC Rating: 24 Vac, 4 A resistive, 2 A inductive
DC Rating: 12 to 30 Vdc, DC 2 A
Switching hysteresis: 2°
Switch Range:Switch A — 0 to 90° range in 5° intervals
Recommended range usage — 0 to 45°
Factory setting — 5°
Switch B — 0 to 90° range in 5° intervals
Recommended range usage — 45 to 90°
Factory setting — 85°
Timing: 125 sec. at 60 Hz, 150 sec. at 50 Hz
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Mechanical
Output torque rating: 88 lb‑in. (10 N‑m).
Stroke: Normal angle of rotation is 90°, limited to a maximum of 95°. Field adjustable to limit
travel on either end of stroke. Set for 5° preload at the factory.
Position indicator: Adjustable pointer is provided for position indication. See the Note in
“Switch Range.”
Output shaft setscrew: tightening torque 55 to 60 lb-in. (6.3 to 6.8 N-m).
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications
Environment
Temperature Limits
Shipping and storage: ‑40 to 158 °F (‑40 to 70 °C) ambient.
Operating: -25 to 130 °F (‑32 to 55 °C) ambient.
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA Type 2.
Agency Listings
UL
UL‑873, Underwriters Laboratories.
European Community
EMC Directive (89/336/EEC). Emissions (EN50081-1). Immunity (EN50081-2).
cUL
Canadian Standards C22.2 No. 24-93.
Accessories
AM-726
Rotary-to-Linear Bracket
AM-727
Rotary-to-Linear Crank Arm
AM-728
Conduit Adapter
AM-741
Weather Shield Kit
Figure-2 MF41-6083 and MS41-6083 Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MF41-6153 and MS41-6153 Actuators
For non-spring return applications requiring floating or proportional
modulation control of dampers and valves in HVAC systems.
Features:
•
•
•
•
•
•
Direct mount to round or square damper shaft
133 lb-in (15 N-m) torque rating
Does not require any limit switches
Manual override to allow positioning for installation and manual operation
MF41-6153 provides floating point control (drive open-hold-drive closed)
MS41-6153 provides proportional control compatible with 0 to 10 Vdc or 0
to 20 mAdc
• 5-year warranty
Actuator Specifications
Inputs
Control Signal
MF41-6153 — Three position.
MS41-6153 — Proportional, 0 to 10 Vdc, input resistance 100 kW.
Power Requirements
All 24 Vac circuits are Class 2.
Part Numbers
Connections
Motor Type
Power Input @ 50/60 Hz
Voltage
Running VA
Holding VA
Watts
MF41-6153
24 Vac +20/-15%
3.0
—
3.0
MS41-6153
24 Vac +20/-15%
5.0
1.2
4.0
3 ft. (91 cm) long plenum-rated cables, 18 AWG color coded leads.
Synchronous.
Outputs
Electrical
Timing: Approx. 125 sec. at 60 Hz; 150 sec. at 50 Hz.
Dual Auxiliary Switch Ratings
AC Rating 24 Vac, AC 6A resistive, AC 2A inductive.
DC Rating 12 to 30 Vdc, DC 2A.
Switch Ranges
Switch A 0° to 90° with 5° intervals.
Recommended Range Usage 0° to 45°.
Factory Setting 5°.
Switch B 0° to 90° with 5° intervals.
Recommended Range Usage 45° to 90°.
Factory Setting 85°.
Switch Hysteresis 2°.
Mechanical
Output torque rating: 133 lb-in (15 N-m).
Stroke: Angle of rotation is limited to a nominal 90° (maximum 95°), field
adjustable to limit travel on either end of stroke. Set for 5° preload at the factory.
Position indicator: Adjustable pointer is provided for position indication.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Shaft Sizes:1/4” to 3/4” (6.4 mm to 20.5 mm) diameter round
1/4” to 1/2” (6.4 mm to 13 mm) square
Minimum Shaft Length: 3/4” (20 mm)
Nominal Damper Area: Actuator sizing should be done in accordance with
damper manufacturer’s specifications.
Weight: 2.2 lb (1 kg)
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Environment
Temperature Limits
Shipping and storage: ‑40 to 158 °F (‑40 to 70 °C) ambient.
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 1 (IEC IP54).
Operating: -25 to 130 °F (32 to 55 °C)
Agency Listings (Actuator)
UL
UL-873, Underwriters Laboratories.
European Community
EMC Directive (89/336/EEC). Immunity (EN61000-6-2). Emission (EN 50081-1).
cUL
Canadian Standards C22.2 No. 24-93.
Accessories
AM-735
Crank Arm Kit
AM-736
Crank Arm Kit with Bracket
AM-737
Universal Crank Arm for Honeywell Floor Mount Mod Motor
AM-740
Replacement Kit
AM-741
Weather Shield Kit
Figure-3 MF41-6153 and MS41-6153 Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MA40-704X, MF40-7043, and MS40-7043 Series Actuators
For spring return applications requiring floating, two-position, or
proportional modulation control of dampers and valves in HVAC systems.
Features:
•
•
•
•
•
Direct mount to round or square damper shaft
35 lb-in (4 N-m) torque rating
Overload protection throughout rotation
Optional built-in auxiliary switches
True mechanical clockwise or counterclockwise spring return operation for
reliable, positive close-off in airtight applications
• Visual position indicator
• Direct acting or reverse acting control mode available on proportional
models
• Rotation limiting available
• Rugged die-cast housing for NEMA 2/IP54 rating
• 5-year warranty
Actuator Specifications
Inputs
Control Signal
MA40‑704X and MA40‑704X‑501 — On‑off. SPST control contacts or Triacs (500 mA
rated).
MF40-7043 and MF40-7043-501 — Floating point control, 24Vac.
MS40-7043 and MS40-7043-501 — Spring return, proportional, 2 to 10 Vdc or 4 to
20 mAdc with a 500 W resistor.
Power Requirements
All 24 Vac circuits are Class 2. All circuits 30 Vac and above are Class 1.
Part Numbers
Connections
Voltage
50/60 Hz
Running
50 Hz
Holding
60 Hz
50 Hz
60 Hz
W
W
VA
W
VA
W
DC
Amps
MA40-7043 and
MA40-7043‑501
24 Vac ± 20%
22-30 Vdc
4.4
2.9
4.4
2.9
0.11
0.8
0.8
MS40-7043 and
MS40-7043‑501
24 Vac ± 20%
22-30 Vdc
5.6
4.2
5.6
4.2
0.15
2.4
2.4
MS40-7043-MP
MS40-7043-MP5
24 Vac ± 20%
22-30 Vdc
6.6
5.0
6.6
5.0
0.17
3.2
3.2
MF40-7043 and
MF40-7043‑501
24 Vac ± 20%
22-30 Vdc
5.9
4.4
5.9
4.4
0.17
2.9
2.9
MA40-7040 and
MA40-7040‑501
120 Vac ± 10%
6.4
3.8
4.3
3.4
—
1.6
1.2
MA40-7041 and
MA40-7041-501
230 Vac ± 10%
5.8
4.1
4.6
3.9
—
1.5
1.2
MA40‑704X and MA40‑704X‑501 — 3 ft. (91 cm) long, appliance cables, 1/2 in.
conduit connector. For M20 Metric conduit, use AM-756 adaptor.
MF40-7043 and MF40-7043-501, MS40-7043 and MS40-7043-501 — 3 ft. (91 cm)
long, plenum-rated cables, 1/2 in. conduit connector. For M20 Metric conduit, use
AM-756 adaptor.
Motor Type
Brush—MA40-704X.
Brushless DC—MF40-7043, MS40-7043.
Outputs
Electrical
Control Mode: Switch provided for selection of direct acting or reverse acting control
mode on proportional models.
Timing: Approximate timing for MA40-704X series is 50 seconds. Approximate timing
for MF40-7043 series or M40-7043 series is 130 seconds.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Electrical (continued)
One auxiliary switch available with MX40-7043-501 and MS40-7043-MP5, SPDT 6A
resistive @ 24 Vac, adjustable 0 to 95° (0 to 1 scale). Switch meets VDE requirements
for 6 (1.5)A, 24 Vac.
One auxiliary switch available with MA40-7040-501 or MA40-7041-501, SPDT 6A
resistive @ 250 Vac, adjustable 15 to 95° (MIN to 1 scale). Switch meets VDE
requirements for 6 (1.5)A, 250 Vac.
Position Feedback Voltage “AO”: 2 to 10 Vdc (maximum 0.5 mA) output signal for
position feedback or operation of up to four slave actuators.
Mechanical
Output Torque Rating: 35 lb‑in. (4 N‑m) minimum, 150 lb-in. (17 N-m) maximum.
Stroke: Rotation is limited to 95° ± 5° maximum, adjustable from 40 to 95 ° with a
mechanical stop.
Position Indicator: Visual indicator, 0 to 1 (0 is the spring‑return position).
Direction of Rotation: CW or CCW rotation is available through reversible mounting.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Damper Shaft Size: Up to 5/8” in diameter and 1/2” square. With AM‑710, up to 3/4” in
diameter and 1/2” square.
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications.
Environment
Temperature Limits
Shipping and storage: ‑40 to 160 °F (‑40 to 71 °C) ambient.
Operating: -22 to 140 °F (-30 to 60 °C).
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 2 (IEC IP54).
Agency Listings
UL
UL 873, Underwriters Laboratories (File #9429 Category Temperature-Indicating and
Regulating Equipment). cUL
Canadian Standards C22.2 No. 24.
European Community
EMC Directive (89/336/EEC). Low Voltage Directive (72/23/EEC).
Australia
This product meets requirements to bear the C-Tick Mark according to the terms
specified by the Communications Authority under the Radiocommunications Act 1992.
Figure-4 MX40-704X Series Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MA41‑707X, MF41‑7073, and MS41‑7073 Series Actuators
For spring return applications requiring floating, twoposition, or proportional modulation control of dampers and
valves in HVAC systems.
Features:
•
•
•
•
•
Direct mount to round or square damper shaft
60 lb-in (7 N-m) torque rating
Overload protection throughout rotation
Optional built-in auxiliary switches
Provides true mechanical clockwise or counterclockwise
spring return operation for reliable positive close-off in airtight
applications
• Visual position indication
• Direct acting or reverse acting control mode available on
proportional models
•
•
•
•
Rotation limiting available
Rugged die-cast housing for NEMA 2/IP54 rating
Manual override
5-year warranty
Actuator Specifications
Inputs
Control Signal
MA41‑707X and MA41‑707X‑502 — On‑off. SPST control contacts or Triacs (500 mA rated).
MF41-7073 and MF41-7073-502 — Floating point control, 24Vac.
MS41-7073 and MS41-7073-502 — Spring return, proportional, 2 to 10 Vdc or
4 to 20 mAdc with a 500 W resistor.
Power Requirements
All 24 Vac circuits are Class 2. All circuits 30 Vac and above are Class 1.
Part Numbers
Connections
Motor Type
Voltage
50/60 Hz
Running
50 Hz
Holding
60 Hz
W
VA
W
DC
Amps
50 Hz
VA
60 Hz
W
W
MA41‑7073 and
MA41‑7073‑502
24 Vac ± 20%
22-30 Vdc
4.8
3.2
4.8
3.2
0.13
0.8
0.8
MS41-7073 and
MS41-7073-502
24 Vac ± 20%
22-30 Vdc
5.8
4.6
5.8
4.6
0.17
2.3
2.3
MF41-7073 and
MF41-7073-502
24 Vac ± 20%
22-30 Vdc
6.2
4.8
6.2
4.8
0.18
2.8
2.8
MA41‑7070 and
MA41‑7070‑502
120 Vac ± 10%
10.7
4.2
5.6
3.6
—
2.0
1.2
MA41‑7071 and
MA41‑7071‑502
230 Vac ± 10%
17.0
5.1
8.0
4.0
—
2.7
1.4
3 ft. (91 cm) long, appliance cables, 1/2 in. conduit connectors. For M20 Metric conduit, use
AM-756 adaptor.
Brush—MA41-707X.
Brushless DC—MF41-7073, MS41-7073.
Outputs
Electrical
Control Mode: Switch provided for selection of direct acting or reverse acting control mode on
proportional models.
Timing: Approximate timing for MA41-707X series is 80 seconds. Approximate timing for
MF41-7073 series or MS41-7073 series is 195 seconds.
Two auxiliary switches available with MX41-7071-502 or MX41-7070-502, SPDT 7A resistive
@ 250 Vac, one fixed @ 5° and one adjustable 25 to 85°. Switch meets VDE requirements for
7 (2.5)A, 250 Vac.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Electrical (continued)
Two auxiliary switches available with MX41-7073-502, SPDT 7A resistive @ 24 Vac, one fixed
@ 5° and one adjustable 25 to 85°. Switches meet VDE requirements for 6 (1.5)A, 24 Vac.
Position Feedback Voltage “AO”, 2 to 10 Vdc (maximum 0.5 mA) output signal for position
feedback or operation of up to four slave actuators.
Mechanical
Output Torque Rating: 60 lb‑in. (7 N‑m) minimum, 250 lb-in. (28 N-m) maximum.
Stroke: Rotation is limited to 95° ± 5° maximum, adjustable from 30 to 95° with AM‑689
rotation limiter.
Position Indicator: Pointer and (-5 to 90°) scale are provided for position indication (-5° is the
normal, or spring‑return, position).
Direction of Rotation: CW or CCW rotation is available through reversible mounting.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Damper Shaft Size: Up to 3/4” in diameter and 1/2” square. With AM‑687, up to 1.05” in
diameter and 5/8” square.
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications.
Manual Override: For MX41-707X manual override rotation is adjustable from -5° to 85° by
using manual override crank.
Environment
Temperature Limits
Shipping and storage: ‑40 to 160 °F (‑40 to 71 °C) ambient.
Operating: -22 to 140 °F (-30 to 60 °C).
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 1. NEMA 2 (IEC IP54) with conduit connector in the down position.
Agency Listings
UL
UL 873, Underwriters Laboratories (File #9429 Category Temperature-Indicating and
Regulating Equipment).
cUL
Canadian Standards C22.2 No. 24.
European
Community
EMC Directive (89/336/EEC). Low Voltage Directive (72/23/EEC).
Australia
This product meets requirements to bear the C-Tick Mark according to the terms specified by
the Communications Authority under the Radiocommunications Act 1992.
Figure-5 MX41-707X Series Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MA41‑715X, MF41-7153, and MS41-7153 Series Actuators
For spring return applications requiring floating, twoposition, or proportional modulation control of dampers and
valves in HVAC systems.
Features:
•
•
•
•
•
Direct mount to round or square damper shaft
133 lb-in (15 N-m) torque rating
Overload protection throughout rotation
Optional built-in auxiliary switches
True mechanical clockwise or counterclockwise spring return
operation for reliable positive close-off in airtight applications
• Visual position indicator
• Direct acting or reverse acting control mode available on
proportional models
•
•
•
•
Rotation limiting available
Rugged die-cast housings for NEMA 2/IP54
Manual override
5-year warranty
Actuator Specifications
Inputs
Control Signal
MA41-715X and MA41-715X-502 — On‑off. SPST control contacts or Triacs (500 mA
rated).
MF41-7153 and MF41-7153-502 — Floating point control 24 Vac.
MS41‑7153 and MS41‑7153-502 — Proportional, 2 to 10 Vdc or 4 to 20 mAdc with a 500 W
resistor.
Power Requirements
All 24 Vac circuits are Class 2. All circuits 30 Vac and above are Class 1.
Part Numbers
Connections
Motor Type
Voltage
50/60 Hz
Running
50 Hz
Holding
60 Hz
W
VA
W
DC
Amps
50 Hz
VA
60 Hz
W
W
MA41-7153 and
MA41-7153-502
24 Vac ± 20%
22-30 Vdc
9.8
7.5
9.7
7.5
0.29
2.8
2.8
MS41‑7153 and
MS41‑7153-502
24 Vac ± 20%
22-30 Vdc
9.8
7.4
9.7
7.4
0.28
2.9
2.9
MF41-7153 and
MF41-7153-502
24 Vac ± 20%
22-30 Vdc
9.8
7.7
9.7
7.7
0.30
3.3
3.3
MA41-7150 and
MA41-7150-502
120 Vac ± 10%
11.7
8.8
10.0
8.4
—
3.6
5.0
MA41-7151 and
MA41-7151-502
230 Vac ± 10%
15.5
9.5
10.6
8.5
—
4.6
3.3
3 ft. (91 cm) long, appliance cable, 1/2 in. conduit connectors. For M20 Metric conduit, use
AM-756 adaptor.
Brushless DC—MA41-715X, MF41-7153, MS41-7153.
Outputs
Electrical
Control Mode: Switch provided for selection of direct acting or reverse acting control mode
on proportional models.
Timing: Approximate timing is 190 seconds.
Two auxiliary switches available with MA41-7151-502 or MF41-7150-502, SPDT 7A
resistive @ 250 Vac, one fixed @ 5° and one adjustable 25 to 85°. Switch meets VDE
requirements for 7 (2.5)A, 250 Vac.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Electrical (continued)
Two auxiliary switches available with MX41-7153-502, SPDT 7A resistive @ 24 Vac, one
fixed @ 5° and one adjustable 25 to 85°. Switches meet VDE requirements for
6 (1.5)A, 24 Vac.
Position Feedback Voltage, 2 to 10 Vdc (maximum 0.5 mA) output signal for position
feedback or operation of up to four slave actuators.
Mechanical
Output Torque Rating: 133 lb‑in. (15 N‑m) minimum, 350 lb-in. (40 N-m) maximum.
Stroke: Rotation is limited to 95° ± 5° maximum, adjustable from 30 to 95° with AM‑689
rotation limiter.
Position Indicator: Pointer and (-5 to 90°) scale are provided for position indication (-5° is
the normal, or spring‑return, position).
Direction of Rotation: CW or CCW rotation is available through reversible mounting.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Damper Shaft Size: Up to 3/4” in diameter and 1/2” square. With AM‑687, up to 1.05” in
diameter and 5/8” square.
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications.
Manual Override: For MX41-715X rotation is adjustable from -5° to 85° by using manual
override crank.
Environment
Temperature Limits
Shipping and storage: ‑40 to 160 °F (‑40 to 71 °C) ambient.
Operating: -22 to 140 °F (-30 to 60 °C).
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 1. NEMA 2 (IEC IP54) with conduit connector in the down position.
Agency Listings
UL
UL 873, Underwriters Laboratories (File #9429 Category Temperature-Indicating and
Regulating Equipment).
cUL
Canadian Standards C22.2 No. 24.
European Community
EMC Directive (89/336/EEC). Low Voltage Directive (72/23/EEC).
Australia
This product meets requirements to bear the C-Tick Mark according to the terms specified
by the Communications Authority under the Radiocommunications Act 1992.
Figure-6 MX41-715X Series Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MA40-717X, MF40-7173, and MS40-717X Series Actuators
For spring return applications requiring floating, two-position, or
proportional modulation control of dampers and valves in HVAC
systems.
Features:
•
•
•
•
•
•
Direct mount to round or square damper shaft
150 lb-in (17 N-m) torque rating
Overload protection throughout rotation
Oil immersed gear train provides continuous lubrication
NEMA 4 housing (IEC IP56)
Automatic current sensing motor control provides extended
reliability and repeatable timing
• Provides true mechanical clockwise or counterclockwise spring
return operation for reliable positive close-off in airtight
applications
• MA40-717X models provide on-off control
• MF40-7173 models provide floating point control (drive open-holddrive closed)
• MS40-717X models provide proportional control compatible with 2
to 10 Vdc or 4 to 20 mAdc with the addition of a 500 ohm resistor
(not included)
• 5-year warranty
• Can be double mounted (gang mounting) to accommodate high
torque application requirements (2 to 4 actuators)
• MS40-717x models provide position feedback signal
Actuator Specifications
Inputs
Control Signal
MA40-717X — Two wire, SPST or Triacs.
MF40-7173 — SPDT floating control output, Triacs (500 mA rated), or 2 SPST contacts.
MS40-717X — proportional, 2 to 10 Vdc or 4 to 20 mAdc with the addition of a 500 ohm
resistor (not included).
Power Requirements
All 24 Vac and 22-30 Vdc circuits are Class 2. All circuits 30 Vac and above are Class 1.
Part Numbers
MA40-7173
MS40-7173
MF40-7173
MA40-7170
Impedance
Power Input @ 50/60 Hz
Voltage
Running VA
Holding VA
Watts
24 Vac ±20%
7.4
5.1
5.3
22-30 Vdc
5.0
3.0
5.0
24 Vac ±20%
7.8
4.7
5.5
22-30 Vdc
5.6
2.5
5.0
24 Vac ±20%
8.1
5.3
5.8
22-30 Vdc
5.7
3.6
5.7
120 Vac ±10%
8.4
6.6
6.2
MS40-7170
120 Vac ±10%
8.5
5.2
6.4
MA40-7171
240 Vac ±10%
9.8
8.5
6.5
MS40-7171
240 Vac ±10%
10.8
9.0
7.2
2 to 10 Vdc, 121KW. 4 to 20 mAdc, 500W (user supplied) (MS40-717X models only).
Connections
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Class 1:
Class 2 Power and
Control:
Motor Type
24 inch (61 cm) long appliance cables, 18 AWG color coded leads. 1/2 in. conduit
connector. For M20 Metric conduit, use AM-756 adaptor.
36 inch (91 cm) Long, 22 AWG color coded appliance cable pigtail leads. 1/2 in. conduit
connector. For M20 Metric conduit, use AM-756 adaptor.
Brushless DC
Outputs
Electrical
Stroke: Electronically limited to 92° ±1° (MS). MF-MA Mechanically limited To 101° ±1°.
Timing: Approximate timing is 147 sec. (MS); 162 sec. for MF and MA models.
Mechanical
Output Torque Rating: 150 lb‑in. (17 N‑m) minimum, 545 lb‑in. (61.8 N‑m) maximum.
Position Indicator: Pointer and scale are provided for position indication (0° is the
normal, or spring‑return, position).
Direction of Rotation: CW or CCW rotation is available through reversible mounting.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Damper Shaft Size: Up to 3/4” in diameter, 1/2” square. With AM‑687, up to 1.05” in
diameter and 5/8” square.
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications.
Environment
Temperature Limits
Shipping and storage: ‑40 to 160 °F (‑40 to 71 °C) ambient.
Operating: ‑25 to 140 °F (‑32 to 60 °C).
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 1 (IEC IP10). NEMA 4 (IEC IP 56) with customer supplied water tight conduit
connectors.
Agency Listings
UL
UL 873, Underwriters Laboratories (File #9429 Category Temperature-Indicating and
Regulating Equipment).
European Community
EMC Directive (2004/108/EC). Low Voltage Directive (72/23/EEC).
cUL
Canadian Standards C22.2 No. 24-93.
Australia
This product meets requirements to bear the C-Tick Mark according to the terms
specified by the Communications Authority under the Radiocommunications Act 1992.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Figure-7 MX40-717X Series Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
MF41-6343 and MS41-634X Series Actuators
For non-spring return applications requiring floating or
proportional modulation control of dampers and valves in
HVAC systems.
Features:
•
•
•
•
•
•
Direct mount to round or square damper shaft
300 lb-in (34 N-m) torque rating
Overload protection throughout rotation
Oil immersed gear train provides continuous lubrication
NEMA 4 housing (IEC IP56)
Manual override to allow positioning for installation and
manual operation
• Automatic current sensing motor control provides extended
reliability and repeatable timing
• MF41-6343 models provide floating point control (drive
open-hold-drive closed)
• MS41-634X models provide proportional control compatible
with 2 to 10 Vdc or 4 to 20 mAdc with the addition of a 500
ohm resistor (not included)
• 5-year warranty
• Can be double-mounted (gang mounted) to accomodate high
torque application requirements ( 2 to 4 actuators)
• MS41-634x models provide position feedback signal
Actuator Specifications
Inputs
Control Signal
MF41-6343 — SPDT floating control output, Triacs (500 mA rated), or 2 SPST contacts.
MS41-634X — proportional, 2 to 10 Vdc or 4 to 20 mAdc with the addition of a 500 ohm
resistor (not included).
Power Requirements
All 24 Vac and 22-30 Vdc circuits are Class 2. All circuits 30 Vac and above are Class 1.
Part Numbers
Power Input @ 50/60 Hz
Voltage
Running VA
Holding VA
Watts
24 Vac ±20%
5.6
4.0
3.6
22-30 Vdc
3.4
2.2
3.4
MS41-6340
120 Vac ±10%
7.5
6.2
4.7
MS41-6341
240 Vac ±10%
9.0
8.1
5.0
24 Vac ±20%
5.7
4.1
3.9
22-30 Vdc
4.1
3.0
4.1
MS41-6343
MF41-6343
Connections
Class 1:
Class 2 Power and
Control:
Motor Type
24 inch (61 cm) long appliance cables, 1/2 in. conduit connector. For M20 Metric conduit,
use AM-756 adaptor.
36 inch (91 cm) long, 22 AWG color coded appliance cable pigtail leads. 1/2 in. conduit
connector. For M20 Metric conduit, use AM-756 adaptor.
Brushless DC
Outputs
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Actuator Specifications
Electrical
Stroke: Electronically limited to 92° ±1° (MS). MF Mechanically limited To 101° ±1°.
Mechanical
Output torque rating: 300 lb‑in. (34 N‑m) minimum, 650 lb‑in. (73.7 N‑m) maximum.
Timing: Approximate timing is 148 sec. (MS) and 162 sec. for MF models.
Position indicator: Pointer and scale are provided for position indication).
Direction of rotation: CW or CCW rotation is available through reversible mounting.
Damper Shaft Clamp: Direct coupled using a through hole output hub.
Damper Shaft Size: 3/8” to 1/2” round and 3/8” to 1/2” square. With AM‑754, up to 1.05”
in diameter and 5/8” square.
Nominal Damper Area: Actuator sizing should be done in accordance with damper
manufacturer’s specifications.
Manual Override: Activated by the manual override crank.
Environment
Temperature Limits
Shipping and storage: ‑40 to 160 °F (‑40 to 71 °C) ambient.
Operating: ‑25 to 140 °F (‑32 to 60 °C).
Humidity
5 to 95% RH, non‑condensing.
Locations
NEMA 1 (IEC IP10). NEMA 4 (IEC IP56) with customer supplied water tight conduit
connectors.
Agency Listings
UL
UL 873, Underwriters Laboratories (File #9429 Category Temperature-Indicating and
Regulating Equipment).
European Community
EMC Directive (2004/108/EC). Low Voltage Directive (72/23/EEC).
cUL
Canadian Standards C22.2 No. 24-93.
Australia
This product meets requirements to bear the C-Tick Mark according to the terms
specified by the Communications Authority under the Radiocommunications Act 1992.
Figure-8 MX41-634X Series Mounting Dimensions.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Damper Actuator Cross Reference
Schneider Electric assumes no responsibility for guaranteeing the acceptability of any suggested replacement in this section.
The emphasis has been placed on providing a replacement actuator of the same specifications wherever possible. The user
must determine the acceptability of the substitution by reviewing the actuator specifications.
The cross reference tables list Direct-Coupled Actuators which may replace obsolete SEC and Belimo devices, as well as older
TAC devices. The tables list two-position, floating, and proportional actuators. The devices to be replaced are listed
alphanumerically in the left-hand column, with the suggested replacement in the center column. The replacement actuators in
this list represent what we believe are equivalent units.
SEC to Current Actuators
SEC P/N
Current P/N
Description
—
MA40-7041
230 Vac 35 lb-in. (4 N-m) (2-position)
—
MA40-7041-501
230 Vac 35 lb-in. (4 N-m) w/aux switch (2-position)
—
MA41-7071
230 Vac 60 lb-in. (7 N-m) (2-position) w/manual override
—
MA41-7071-502
230 Vac 60 lb-in. (7 N-m) w/aux switch (2-position) w/manual override
—
MA40-7170
120 Vac 150 lb-in. (17 N-m) (17 N-m) (2-position)
—
MA40-7171
240 Vac 150 lb-in. (17 N-m) (2-position)
—
MA40-7173
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (2-position)
—
MF41-7073
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (floating) w/manual override
—
MF41-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (floating) w/manual override
—
MF41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (floating) w/manual override
—
MF41-7153-502
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) w/aux switch (floating) w/manual override
—
MF40-7173
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (floating)
—
MS41-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (proportional) w/manual override
—
MS41-7153-502
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) w/aux switch (proportional) w/manual override
—
MS40-7170
120 Vac 150 lb-in. (17 N-m) (proportional)
—
MS40-7171
240 Vac 150 lb-in. (17 N-m) (proportional)
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (proportional)
—
MS40-7173
—
MS41-6340
120 Vac 300 lb-in. (34 N-m) NSR (proportional)
—
MS41-6341
240 Vac 300 lb-in. (34 N-m) NSR (proportional)
MA-7101
MA40-7040
120 Vac 35 lb-in. (4 N-m) (2-position)
MA-7101-500
MA40-7040-501
120 Vac 35 lb-in. (4 N-m) w/aux switch (2-position)
MA-7103
MA40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (2-position)
MA-7103-500
MA40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (2-position)
MA-7201
MA41-7070
120 Vac 60 lb-in. (7 N-m) (2-position) w/manual override
MA-7201-500
MA41-7070-502
120 Vac 60 lb-in. (7 N-m) w/aux switch (2-position) w/manual override
MA-7203
MA41-7073
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (2-position) w/manual override
MA-7203-500
MA41-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (2-position) w/manual override
MA-7501
MA41-7150
120 Vac 133 lb-in. (15 N-m) (2-position) w/manual override
MA-7501-502
MA41-7150-502
120 Vac 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
MA-7503
MA41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (2-position) w/manual override
MA-7503-502
MA41-7153-502
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
MA-7505
MA41-7151
230 Vac 133 lb-in. (15 N-m) (2-position) w/manual override
MA-7505-502
MA41-7151-502
230 Vac 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
MF41-6043
24 Vac 35 lb-in. (4 N-m) NSR (floating)
MF41-6043-502
24 Vac 35 lb-in. (4 N-m) NSR (floating), w/two aux switches
MF41-6043-510
24 Vac 35 lb-in. (4 N-m) NSR (floating), feedback potentiometer
MF41-6083
24 Vac 70 lb-in. (8 N-m) spdt NSR (floating)
MF41-6083-502
24 Vac 70 lb-in. (8 N-m) NSR (floating), w/two aux switches
MF41-6083-510
24 Vac 70 lb-in. (8 N-m) NSR (floating), feedback potentiometer
MF-6633
MF41-6153
24 Vac 133 lb-in. (15 N-m) spdt NSR (floating)
MF-6733
MF41-6343
24 Vac or 33-30 Vdc 300 lb-in. (34 N-m) spdt NSR (floating)
MF-7103
MF40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (floating)
MF-7103-500
MF40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (floating)
MF-6103
MF-6203
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
SEC P/N
Current P/N
Description
MS41-6043
24 Vac 35 lb-in. (4 N-m) NSR (proportional)
MS41-6043-502
24 Vac 35 lb-in. (4 N-m) NSR (proportional), w/two aux switches
MS41-6043-520
24 Vac 35 lb-in. (4 N-m) NSR (proportional), adjustable start point (offset) and span
MS41-6043-522
24 Vac 35 lb-in. (4 N-m) NSR (proportional), w/two aux switches, adjustable start point (offset) and
span
MS41-6083
24 Vac 70 lb-in. (8 N-m) 2-10 Vdc/4-20 mAdc NSR (proportional)
MS41-6083-502
24 Vac 70 lb-in. (8 N-m) NSR (proportional), w/two aux switches
MS41-6083-520
24 Vac 70 lb-in. (8 N-m) NSR (proportional), adjustable start point (offset) and span
MS41-6083-522
24 Vac 70 lb-in. (8 N-m) NSR (proportional), w/two aux switches, adjustable start point (offset) and
span
MS41-6153
24 Vac 133 lb-in. (15 N-m) 2-10 Vdc/4-20 mAdc NSR (proportional)
MS41-6153-502
24 Vac 133 lb-in. (15 N-m) NSR (proportional), w/two aux switches
MS-6733
MS41-6343
24 Vac or 22-30 Vdc 300 lb-in. (34 N-m) 2-10 Vdc/4-20 mAdc NSR (proportional)
MS-7103
MS40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (proportional)
MS-7103-500
MS40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (proportional)
MS-7203
MS41-7073
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (proportional) w/manual override
MS-7433
MS41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (proportional) w/manual override
MS-6103
MS-6233
MS-6633
TAC Old to Current
TAC Old
Current
Description
MF40-6043
MF41-6043
24 Vac 35 lb-in. (4 N-m) NSR (floating)
MF40-6043-510
MF41-6043-510
24 Vac 35 lb-in. (4 N-m) NSR (floating), feedback potentiometer
MF40-6043-520
MF41-6043-520
24 Vac 35 lb-in. (4 N-m) NSR (floating), adjustable start point (offset) and span
MF40-6043-522
MF41-6043-522
24 Vac 35 lb-in. (4 N-m) NSR (floating), w/ two aux. switches, adjustable start point (offset) & span
MF40-6083
MF41-6083
24 Vac 70 lb-in. (8 N-m) NSR (floating)
MF40-6153
MF41-6153
24 Vac 133 lb-in. (15 N-m) NSR (floating)
MF40-6343
MF41-6343
24 Vac or 22-30 Vdc 300 lb-in. (34 N-m) NSR (floating)
MS40-6043
MS41-6043
24 Vac 35 lb-in. (4 N-m) NSR (proportional)
MS40-6043-510
MS41-6043-510
24 Vac 35 lb-in. (4 N-m) NSR (proportional), feedback potentiometer
MS40-6043-520
MS41-6043-520
24 Vac 35 lb-in. (4 N-m) NSR (proportional), adjustable start point (offset) and span
MS40-6043-522
MS41-6043-522
24 Vac 35 lb-in. (4 N-m) NSR (proportional), w/ two aux. switches, adjustable start point (offset) &
span
MS40-6083
MS41-6083
24 Vac 70 lb-in. (8 N-m) NSR (proportional)
MS40-6153
MS41-6153
24 Vac 133 lb-in. (15 N-m) NSR (proportional)
MS40-6343
MS41-6343
24 Vac or 22-30 Vdc 300 lb-in. (34 N-m) NSR (proportional)
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Belimo to Current Actuators
Belimo P/N
Current P/N
Description
—
MA40-7170
120 Vac 150 lb-in. (17 N-m) (2-position)
—
MA40-7171
240 Vac 150 lb-in. (17 N-m) (2-position)
—
MA40-7173
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (2-position)
—
MF40-7073
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (floating)
—
MF41-7073
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (floating) w/manual override
—
MF40-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (floating)
—
MF41-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (floating) w/manual override
—
MF40-7173
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (floating)
—
MS41-7073-502
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (proportional) w/manual override
—
MS40-7170
120 Vac 150 lb-in. (17 N-m) (proportional)
—
MS40-7171
240 Vac 150 lb-in. (17 N-m) (proportional)
—
MS40-7173
24 Vac or 22-30 Vdc 150 lb-in. (17 N-m) (proportional)
—
MS41-6340
120 Vac 300 lb-in. (34 N-m) NSR (proportional)
—
MS41-6341
240 Vac 300 lb-in. (34 N-m) NSR (proportional)
AF120
MA41-7150
120 Vac 133 lb-in. (15 N-m) (2-position) w/manual override
AF120-S
MA41-7150-502
120 Vac 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
AF230
MA41-7151
230 Vac 133 lb-in. (15 N-m) (2-position) w/manual override
AF230-S
MA41-7151-502
230 Vac 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
AF24
MA41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (2-position) w/manual override
AF24-3
MF41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (floating) w/manual override
AF24-S
MA41-7153-502
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) w/aux switch (2-position) w/manual override
AF24-3-S
MF41-7153-502
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) w/aux switch (floating) w/manual override
AF24-SR
MS41-7153
24 Vac or 22-30 Vdc 133 lb-in. (15 N-m) (proportional) w/manual override
AF24-SR-S
MS41-7153-502
24 Vac or 22-30 Vdc, 133 lb-in. (15 N-m) w/aux switch (proportional) w/manual override
AFR24-SR
—
24 Vdc or 22-30 Vdc, 133 lb-in. (15 N-m) (proportional)
AFR24-3
—
24 Vdc or 22-30 Vdc, 133 lb-in. (15 N-m) (floating)
AFR24-3-S
—
24 Vdc or 22-30 Vdc, 133 lb-in. (15 N-m) (floating)
AFR120
—
120 Vac, 133 lb-in. (15 N-m) (2-position)
AFR120-S
—
120 Vac, 133 lb-in. (15 N-m) (2-position), w/aux switch
AFR24
—
24 Vac or 22-30 Vdc, 133 lb-in. (15 N-m) (2-position)
AFR24-S
—
24 Vac or 22-30 Vdc, 133 lb-in. (15 N-m) (2-position), w/aux switch
GM24
MF41-6343
24 Vac or 22-30 Vdc 300 lb-in. (34 N-m) spdt NSR (floating)
GM24-SR
MS41-6343
24 Vac or 22-30 Vdc300 lb-in. (34 N-m) 2 to 10 Vdc/4 to 20 mAdc NSR (proportional)
LF120
MA40-7040
120 Vac 35 lb-in. (4 N-m) (2-position)
LF120-S
MA40-7040-501
120 Vac 35 lb-in. (4 N-m) w/aux switch (2-position)
LF230
MA40-7041
230 Vac 35 lb-in. (4 N-m) (2-position)
LF230-S
MA40-7041-501
230 Vac 35 lb-in. (4 N-m) w/aux switch (2-position)
LF24
MA40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (2-position)
LF24-3
MF40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (floating)
LF24-S
MA40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (2-position)
LF24-3-S
MF40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (floating)
LF24-SR
MS40-7043
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) (proportional)
LF24-SR-S
MS40-7043-501
24 Vac or 22-30 Vdc 35 lb-in. (4 N-m) w/aux switch (proportional)
LM24
MF41-6043
24 Vac 35 lb-in. (4 N-m) NSR (floating)
LM24-10P
MF41-6043-510
24 Vac 35 lb-in. (4 N-m) NSR (floating), feedback potentiometer
LM24-S
MF41-6043-502
24 Vac 35 lb-in. (4 N-m) NSR (floating), w/two aux switches
LM24-SR
MS41-6043
24 Vac 35 lb-in. (4 N-m) NSR (proportional)
—
MS41-6043-520
24 Vac 35 lb-in. (4 N-m) NSR (proportional), adjustable start point (offset) and span
—
MS41-6043-522
24 Vac 35 lb-in. (4 N-m) NSR (proportional), w/two aux switches, adjustable start point (offset) and span
—
MS41-6043-502
24 Vac 35 lb-in. (4 N-m) NSR (proportional), w/two aux switches
NF120
—
120 Vac 60 lb-in. (7 N-m) (2-position)
NF120-S
—
120 Vac 60 lb-in. (7 N-m) w/aux switch (2-position)
NF230
—
230 Vac 60 lb-in. (7 N-m) (2-position)
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
Belimo P/N
Current P/N
Description
NF230-S
—
230 Vac 60 lb-in. (7 N-m) w/aux switch (2-position)
NF24
—
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (2-position)
NF24-S
—
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) w/aux switch (2-position)
NF24-SR
—
24 Vac or 22-30 Vdc 60 lb-in. (7 N-m) (proportional)
NM24
NM24-SR
SM24
SM24-SR
MF41-6083
24 Vac 70 lb-in. (8 N-m) spdt NSR (floating)
MF41-6083-502
24 Vac 70 lb-in. (8 N-m) NSR (floating), w/two aux switches
MF41-6083-510
24 Vac 70 lb-in. (8 N-m) NSR (floating), feedback potentiometer
MS41-6083
24 Vac 70 lb-in. (8 N-m) 2 to 10 Vdc/4 to 20 mAdc NSR (proportional)
MS41-6083-502
24 Vac 70 lb-in. (8 N-m) NSR (proportional), w/two aux switches
MS41-6083-520
24 Vac 70 lb-in. (8 N-m) NSR (proportional), adjustable start point (offset) and span
MS41-6083-522
24 Vac 70 lb-in. (8 N-m) NSR (proportional), w/two aux switches, adjustable start point (offset) and span
MF41-6153
24 Vac 133 lb-in. (15 N-m) spdt NSR (floating)
MS41-6153
24 Vac 133 lb-in. (15 N-m) 2 to 10 Vdc/4 to 20 mAdc NSR (proportional)
MS41-6153-502
24 Vac 133 lb-in. (15 N-m) NSR (proportional), w/two aux switches
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014
© 2014 Schneider Electric. All rights reserved.
Schneider Electric F-26646-9
1-888-444-1311 Product Support Services www.schneider-electric.com
August 2014