Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
1
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
- Follow installation manual instructions carefully. Installer must careful to not cause interference
between Navigator System cabling and active / passive car safety device (Ex: Air bags, seat belts, indica
tors, etc…)
- Before any attempt of component removal, the installer must disconnect the vehicle battery and
isolate the ends of the cable.
- Do not attempt this installation operation if there are missing components. Please check the bill of
materials carefully to ensure the kit is complete.
- Installation requires careful attention. If you have concerns about your abilities to perform delicate
operations, then do not begin the installation.
- The car must be secured to not move during installation. Parking brake must be engaged at all times.
- Operation should be made in a clean, safe and well ventilated environment without trip hazards and
slippery floors
- Do not install by yourself if you do not have qualifications and/or tools to perform the retrofit. You
may damage the car’s components and/or the Navigator if not professionally installed.
- Poor installation can result in poor performance, personal injuries and will immediately void the
factory warranty.
- Do not install the Navigator in a position that blocks the driver's view or hinders safe vehicle operation.
2
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Caution
Installation Time is around 2 hours with additional
time required for options installation
Do NOT RUSH and if issues occur contact technical support
3
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Table of contents:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Tools Required –
Bill of Materials –
Cables interconnection identification –
Touchscreen Connections identification –
TRIP Module connection identification –
Vehicle Preparation –
Radio Preparation –
Touchscreen Fascia Installation –
Fascia Trim Preparation –
Lower Console Preparation –
Electrical Connections –
Installation in Vehicle –
Appendix 1 – TRIP Module
Dip Switches
Appendix 2 – Backup Camera Installation
Appendix 3 – Parking Assist
Appendix 4 – RDS Traffic Tuner
Tips & Tricks
Page 5
Page 6
Page 9
Page 15
Page 19
Page 23
Page 31
Page 42
Page 46
Page 50
Page 55
Page 62
Page 73
Page 75
Page 78
Page 81
Page 83
4
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Tools required for successful install -#1 = Patience!!!
Shop Towels & Alcohol
Double Sided tape industrial (RED)
Lighter or heat gun(for heat shrink)
Gloves
Electrical tape
Hacksaw
Philips #2 screwdriver magnetic
Wide flat blade screwdriver
Masking Tape
Side cutters
Knife
Jeweler screw driver set
10mm socket
Ratchet
5
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Bill of materials
Keypad Cable
(Pre-installed)
Aux
cable
Audio Patch
cable
Main I/O 1
Cable
Main I/O 2
Cable
TRIP Serial cable
6
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Bill of materials
Flat ribbon
rubber block
Radio face
plate
LCD Screen
Brackets & screws
(Pre-installed)
Mini Speaker
GPS
antenna
Radio
securing
Brackets
XM radio Antenna
adapter
7
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Bill of materials
Main Touchscreen
(Pre-Installed)
TRIP
Module
Bluetooth antenna
(pre-installed for
MY 2011-Mid
2013 only)
Fascia
Molding
SD Card adapter
External USB & SD
Card Box (Map SD
Card inserted)
8
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 3
System Cable
Connections and
Identification
9
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Rear Backup Camera Cable
- Main I/O 1
Backup lamp +12V
from Camera RED wire
Ground to radio body
GPS Antenna Connection
– Main I/O 1
10
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
External Speaker
Connection – Main I/O 1
TRIP Serial Cable connection:
- 5 Pin to TRIP Module
- 3 Pin(Yellow, Red and Black) to
MAIN I/O 1 Trip Serial cable
- 2 Pin(Blue and Green) to Audio
Patch Cord
11
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Aux Cable connection
– Main I/O 1
AUX in – Connect to AUX input jack of
Audio Patch cable circuit.
AV In connection –
Main I/O 1 (Optional)
Composite & stereo jacks
DVD, Game console etc…
12
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
AV Out Connection –
Main I/O 2 (Optional)
Rear seats Composite stereo jacks
IR Sensor and Remote –
Main I/O 2 (Optional)
13
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
CN-M5 Touchscreen power cable
This is the CompassNAV Audio Patch cord.
This adapter goes in
between the 24 pins
radio connector and
the car harness.
Steering Wheel Control
BLUE & GREEN 2 pins conn.
See page 11
AUX In from MAIN I/O 1
See page 12
14
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 4
Touchscreen Connection
identification
15
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Reserved for
future use
Main I/O 1 Main I/O 2
SD/USB connect
Power Connection
16
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
SD/USB connection
box to SD EXT
connection
SD/USB
Interface
Main I/O Connection #1
17
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Main I/O Connection #2
Not required to plug if:
-
No Remote control
No Rear Seat Screen
No Traffic Tuner
CN-M5 Main Power
Connection for
Touchscreen
18
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 5
Trip Module Connections
and ports identity
19
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Applies ONLY to Elantra 2011- mid-2012 (single radio knob)
Do not use this picture for DIP switches position
TRIP Module Dip
Switch location –
Switches are factory
preset but please
refer to the Appendix
1 correct position.
TRIP Module interface
connections
20
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Trip Module Connections/Cable identification
TRIP 5 pins Cable
wire connections
Ribbon Connector
Keypad Connection
OBDII Parking
Assist cable
(option)
21
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
TRIP module schematic connections
OBD Parking Assist
connector (option)
CN-M5 Screen
TRIP SERIAL
connector MAIN I/O 1
Flat Ribbon
Cable
I/O Keypad cable
Steering wheel cables
22
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 6
Vehicle Preparation
23
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
1. After protecting the area around the
transmission (use masking tape) use the flat
screw driver (that will not mark the vehicle
plastic) to separate the side trim from the
transmission housing. This trim is secured
using white plastic retaining clips.
2. Carefully pry the molding off all the
way up to the radio. Do not force it,
just ease it and be cautious to avoid
damage.
24
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
3.Continue removing the trim piece
(notice the white plastic clips retaining
the trim) until the piece is completely
separated. Store these trim pieces
carefully to avoid damage. Repeat the
process for the other side.
4.Once both trim pieces are removed ,
the radio securing screws are exposed.
Remove the screws indicated and store
safely.
25
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
5.Gently lift the black plastic piece that
surrounds the radio to expose the silver
mounting screws. This part houses the
clock and has a connector at the top.
Carefully unplug the connector before
removing the part completely.
Carefully remove the connector the
powers clock from rear of the black bezel
6.After removal (and clock power
disconnect), remove the retaining
screws that secure the radio to the
dashboard. Store the screws safely.
26
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
7. Gently lift up the radio unit to allow the 3
connectors on the rear (2 x multiway, 1 x XM
antenna) to be disconnected. These are
unplugged by pressing the tab on the top and
pulling gently. Also disconnect the radio FM
antenna (just carefully pull the cable out of
the receptacle.)
8. Exposed connectors after radio
removal. Notice the tab top on the
connectors is pressed to remove the
plug from the radio.
XM
27
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
9. Remove the retaining screws for the
temperature controls module. Using
your hand, grab the bottom of the A/C
control module and carefully pull the
unit forward enough to disconnect the
cables on the rear of the panel.
Insert your hand, fingers up, above the cubby door and reach
the back of the A/C as shown. Pull forward to unsnap it.
10. All connectors are then
disconnected from the temperature
control module by pressing the tab
and pulling the connectors.
28
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
11. The red circles identify the areas
that need to be trimmed to
accommodate the new touchscreen
and bezel mount. Notice the “triangle”
pieces of the securing socket.
12. Using a small saw (or any
appropriate tool) trim the area marked
to reflect the next step. This is
necessary to allow the new panel to be
installed correctly. Clean the entire
area with a vacuum to remove the
plastic debris.
29
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
14. After
removal of the
excess plastic
the dashboard
should look
similar to this.
Notice the
missing triangle
of material.
30
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 7
Radio Preparation
31
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
15. For radio preparation, removed the
bracket and front panel retaining screws as
shown. Repeat for the other side of the
radio.
16. To detach the front panel completely
from the radio, there are 6 retaining tabs
that retain the radio panel in ( 2 on
bottom, 2 on top and 1 either side) .
GENTLY lift these up a little (DO NOT SNAP
THEM OFF) and pry the radio fascia clear
enough to allow access to the cables on
the rear.
32
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
A little pressure is needed from a
screwdriver to lift up the brown locking tab
to allow the connector to freely be
disconnected. Be gentle to avoid
damaging the brown locking tab
Notice the red circles. The cable needs to
be disengaged from the brown locking tab,
to free it from the beige connector.
Separate the white end from the lock by
lifting gently. DO NOT PULL HARD
33
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
ELANTRA 2011 – MID 2013 ONLY
(1 Knob radio version)
Bluetooth antenna is two handed process.
There is a locking ring very close to the
PCB (Printed Circuit Board) that needs to
be disengaged (pulled up slightly) before
pulling cable off the PCB. The cable and
connector are very fragile.
Gently remove the Bluetooth antenna
cable from the circuit board to allow
complete removal.
34
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
After carefully disconnecting the
DELICATE ribbon cable from the display
panel and disconnecting the Bluetooth
antenna the front of the main radio is
shown. (Bluetooth cable is only for the 1 knob radio
version; pre mid-2013)
The front plate needs to be removed from
the radio to allow connection of the
touchscreen. Remove the retaining
screws indicated and save for later use.
Reserve separately the two screws
holding the CD player tray for later use.
35
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Locate the replacement front plate in the
installation kit, install TRIP unit into frame
Install the TRIP interface module into the
plate in the orientation shown. (White
connector exposed on front of plate
oriented away form CD tray, dip switches
at rear)
36
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Gently feed the radio ribbon cable and Bluetooth
antenna (if applicable) through the plate and locate the
plate into the front of the radio with the locators
(shown). Be cautious to avoid causing any internal
damage as the TRIP interface is pushed into the radio
unit. CAUTION Sometimes the TRIP might snag a little on
connectors, carefully maneuver into position.
After carefully installing the TRIP into the Radio unit,
the completed cable routing should look like this.
Install the bracket retaining screws in the locations
shown. The bottom screw doesn’t need to be tighten
now, it will be used to attach the backup camera ground
(if purchased).
Screw the 2 screws reserved previously at these
locations.
Elantra 2011-2012
Elantra 2013
37
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
1
3
2
2
1- The black locking tab in the TRIP module is
carefully lifted to allow the ribbon cable to be
installed into the TRIP module.
2- The flat ribbon contacts (silver) need to be
facing down (to make contact) and the blue
needs to face up. The ribbon must be
CAREFULLY but firmly pushed into the TRIP
connector, ensuring it is parallel and has no
bends or tears.
3- Then fold down gently the locking tab.
4- Then carefully install the rubber retainer,
inserting the bottom piece first into place to
ensure the locking tab and therefore ribbon
cable does not disengage. Caution: Make sure
to insert the bottom of the rubber block first
otherwise the locking tab may fold back and
brake. If the locking tab is broken; stop the
38
installation immediately and contact support.
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
The protruding curve of the ribbon cable
must be CAREFULLY eased back into the
radio unit (under the TRIP module), use just
enough pressure to push into the radio.
Completed TRIP module ribbon cable
installation.
39
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Attach the dash mounting brackets to the
side of the radio using the three
mounting points. Check the alignment
dimples (GREEN circles) that aid in
correct placement of the brackets. These
are supplied in the installation kit.
Repeat for the other side of the radio.
Note – The brackets are not the same,
ensure the bracket installation matches
the images as depicted by the green
circles.
40
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Attach the XM radio antenna adapter
to the radio as shown
You have successfully retrofitted your
factory radio!
41
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 8
Display Installation into
Fascia
(If the screen has been pre installed into the fascia trim, please skip this section)
42
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Prepare the display for mounting into the
new supplied fascia (if this was not
completed already). Snug the screws up but
do not tighten to allow for display
adjustment once installed into fascia.
Install the display unit into the fascia. Take
time to ensure that the alignment is correct
by viewing the outside. Look to ensure the
display is square and level. Tighten the
fascia mounting screws to fix the display in
that position.
43
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Apply LIGHT pressure to the back of the
display to reduce any gaps between fascia
and the display and then tighten the side
screws. Check alignment and make minor
adjustments as necessary.
The screen is preassembled from factory
Install Bluetooth antenna to the side of the
display using 3M double sided tape.
44
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Front of keypad
On rear of keypad install the control
cable for connection to TRIP
module.
45
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 9
Fascia Trim Preparation
46
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Remove the existing factory
clock module from the original
fascia (undo the 2 screws) and
relocate it to the new
replacement fascia.
Transfer the 4 white (or green)
plastic clips from the old trim to
the new trim.
47
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Transfer the 4 white (or green)
plastic clips from the old trim to the
new trim. Pull side of clip gently and
pull up. Install in new fascia.
48
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Touchscreen panel installed into
replacement fascia. Recheck all screws,
alignments and connections.
Ensure that white retainer clips are
relocated from old fascia panel to new
unit for installation.
49
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 12
Lower Console
Preparation
50
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Remove the 2 screws holding the
lower console in place as shown and
reserve.
Unclip the lower console by pulling
forward gently. No need to remove
the lower console completely, just
hold it in place as shown.
51
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Remove the 2 silver screws
holding the top cover of the cubby
as shown and reserve.
Unsnap the top cover by pulling
gently upwards from the back of
the cubby. (see the 3 holding clips
at the back of the top cubby.
Cut out a rectangle opening
exactly as shown and deburr.
52
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Apply 2 strips of double sided tape
at the back of the external media
box as shown.
Affix the External Media Box on
the side of the power outlet wall
as shown.
53
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Route the External Media Box cable
thru the rectangle opening as shown.
Then re-install the cubby top cover in
reverse order. (snap at the back then
screw the 2 silver screws)
Route the External Media box cable to
the head unit by inserting the cable
connector first thru the dash opening
as shown.
Snap in place the whole console and
screw in place using the 2 screws
previously reserved. Re-Install the A/C
control module; secure with the 2
screws reserved previously ensuring
connectors are installed.
54
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 11
Electrical/Wiring
Connections
55
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
In the following section we will:
- Prepare the radio patch cord and attach to the car & radio connectors.
- Install the mini speaker.
- Video Tutorial about this section:
-
https://dl.dropboxusercontent.com/u/70065767/Manuals/Audio%20Patch%20Cord%20Assy.m2ts
Aux
cable
Audio Patch
Cord
TRIP Serial
cable
56
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Attach the TRIP Serial
cable 2 Pin connector to
this connector to the
Audio Patch cord as
shown.
TRIP Serial cable
57
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Attach the AUX cable male
jack into the female of the
Aux switcher board as
shown. Secure in place
with Electrical tape.
Reserve the White and
RED RCA jack to be
connected into the AUX
cable from the MAIN I/O 1
Aux
cable
58
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Connect the Audio Patch
cord to the car matching
connector as shown.
Connectors improperly
seated.
Connectors properly
seated. You should hear a
CLICK.
59
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Reserve the CN-M5 4
pins square connector
for the final assembly.
Attach the TRIP SERIAL
to the MAIN I/O 1 TRIP
SERIAL. (Ref: P:11)
Reserve the TRIP MOD
cable for the final
assembly. It will be
plugged in front of the
trip module (Ref: P:11)
60
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Mini Speaker
Mini speaker installation
before
Driver side kick near gas
pedal
Bottom plastic
mounting
support
The recommended placement of
the mini-speaker is located on the
driver side. Follow up the side kick
near the gas pedal, locate the
plastic lowest plastic support and
install the mini-speaker as shown
with the provided screw. The
speaker is very light and require
only one screw. Once completed,
bring the wire to the head unit for
final install.
61
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Section 12
Installation into Vehicle
62
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Location of double sided tape onto
bottom of GPS antenna. Ensure GPS logo
is still visible on top side.
Using 3M tape attach the GPS antenna to
the top of the radio unit. Store the
excess cable underneath the radio unit
once installed.
63
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
IMPORTANT
Before proceeding to the final installation if you have
purchased the following options, please proceed to their
installation before completing the final assembly.
- Backup Camera
- Parking Assist System
- RDS Traffic Tuner
Appendix 2 page 75
Appendix 3 page 78
Appendix 4 page 81
64
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
After ensure all cables are correctly
brought through to area beneath radio,
attach:
- Radio antenna
- XM antenna
- GND cable,
- Multi-way connectors
Anti vibration tape
placement
And install radio in dashboard. If the
radio does not fit well in place, make
sure there is no unnecessary cables
behind the radio and ensure they are
well placed under it. The radio is
located a little higher than before and
so will not engage in its location
bracket. To avoid vibration use electrical
tape to cushion unit. Affix using the
screws removed earlier.
65
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Once located fish the required
cables through the square opening.
All other cables should be stored
under the unit and not brought
through the hole.
Required Cables exiting the
opening:
CN-M5 power cable
CN-M5 Main I/O 1
CN-M5 Main I/O 2 (if needed)
External media box
66
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Prior the assembly of the trim to the car, please make sure you have at the following
connected properly .
-
GPS Antenna to GPS Serial of MAIN I/O 1
TRIP cable to TRIP Serial of MAIN I/O 1
Mini Speaker to SPK of MAIN I/O 1
AUX cable to AUX of MAIN I/O 1
-
OPTIONS
CAMERA to CAMERA of MAIN I/O 1
Audio Video Extension cord to AVIN of MAIN I/O 1 for external multimedia player
Audio Video Extension cord to AVOUT of MAIN I/O 2 for read seat screen and sound
IR Receiver for Infrared remote of MAIN I/O 2
TMC cable to TMC Traffic receiver of MAIN I/O 2
67
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Prior handling the fascia, connect the
TRIP cable to the TRIP module as
indicated. (5 wires connector) and
Parking Assist System cable if purchased.
Getting ready to attach the new fascia
trim, connect:
- The Bluetooth antenna cable.
- Keypad green cable to the TRIP
module.
- Main I/O 1
- Main I/O 2 (If needed)
- External Media Box
- Navigator device power.
68
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Connect the car harness for the
clock and temperature module
and place fascia carefully making
sure you’re not pinching or
bending sharply any wires.
Align the plastic clips to their
matching holes. Press firmly the
trim surrounding to snap the
clips. Make sure the CD slot is
properly aligned with the trim
slot and look for apparent gaps.
Once completed, you can
proceed with the final assembly.
Screw in place the new trim (2)
Put back the remaining trims.
69
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Reconnect the wires to the car battery and test run the Navigator.
Prior running the radio interface go into the device Settings / TRIP and make sure
your Car Type is:
Car TYPE 15: for Elantra 2011 – Mid 2013 (Single knob type)
Car TYPE 26: for Elantra Mid-2013 + (2 knobs type)
Test all features as per User Manual.
70
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
YOU DID IT!
71
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Left intentionally blank
72
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 1
TRIP Module DIP
Switches
73
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 1 : Trip module DIP switches
Please refer to the DIP switches selection
guide located at the back of the TRIP
module for proper operation.
IMPORTANT
DIP switches proper position are show by
the black squares boxes NOT by the white
crossed boxes.
ON 1 2 3 4
Elantra DIP switches at their correct
positions are show here.
74
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 2
Backup Camera
Installation
75
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 2: Backup Camera install
Unscrew the bottom middle
radio screw and attach the
BLACK wire from the labeled
MAIN I/O 1 “REAR PWR” to the
front of the radio chassis as
shown.
76
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Attach the RED wire from MAIN
I/O 1 “REAR PWR” to the backup
camera RED wire.
Plug the back up camera RCA
jack into the same Yellow
Camera jack of MAIN 1/O 1
77
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 3
Parking Assist
78
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 3: Parking Assist System
OBD II Adapter
Connection of the Parking Assist System is
very simple.
First: Connect the 3 pin connector to the
CAN position of the trip module as
shown.
Second: Connect the OBD II adapter into
Insert into the “CAN” the car OBD interface.
Once inserted, lock it in place by moving
Position
the yellow tab until you hear a “click”.
The OBD adapter will interfere with the
fuse box panel and the car OBD interface
needs to be relocated. See next page…
79
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Release the OBD interface by
disengaging the latch and relocate
lower to be accessed by service
technicians.
Secure properly for driver’s safety.
It is your responsibility to inform
the service personnel of the new
location of the OBD interface and
how to disengage the parking assist
adapter!!!!
80
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Appendix 4
RDS Traffic Tuner
81
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Connect the female TMC FM adapter to
the car male.
FM RDS TMC
Connect the male TMC FM adapter to
the back of the radio. Reserve the
white connector MAIN I/O 2 for the
final assembly.
82
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
Tips and tricks
To avoid over heating wire and connectors, it is recommended you use soldering acid
Flux. This will greatly improve the quality of the soldering points. Before soldering, dip
Into the acid flux paste the end of the soldering rod and apply a little flux to the wire
section you wish to solder.
83
Hyundai Elantra 2011-up CN-M5
Installation manual
Caution – Documentation is an aid to successful installation. No liability is assumed for incorrect installation.
If unsure of expertise required, please consult a qualified installation tech.
END OF MANUAL
84