PSC LINEAR IMAGER 7000 Technical data

PowerScan® 7000BT SRI
Linear Imager
Quick Reference Guide
Datalogic Scanning, Inc.
959 Terry Street
Eugene, Oregon 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures
described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Owners of Datalogic products are hereby granted a non-exclusive, revocable license to reproduce and
transmit this documentation for the purchaser's own internal business purposes. Purchaser shall not
remove or alter any proprietary notices, including copyright notices, contained in this documentation and
shall ensure that all notices appear on any reproductions of the documentation.
Should future revisions of this manual be published, you can acquire printed versions by contacting your
Datalogic representative. Electronic versions may either be downloadable from the Datalogic website
(www.scanning.datalogic.com) or provided on appropriate media. If you visit our website and would like to
make comments or suggestions about this or other Datalogic publications, please let us know via the "Contact Datalogic" page.
Disclaimer
Datalogic has taken reasonable measures to provide information in this manual that is complete and accurate, however, Datalogic reserves the right to change any specification at any time without prior notice.
Datalogic is a registered trademark of Datalogic S.p.A. and the Datalogic logo is a trademark of Datalogic
S.p.A. all licensed to Datalogic Scanning, Inc. All other trademarks and trade names referred to herein are
property of their respective owners.
Patents
This product may be covered by one or more of the following patents: 4603262 • 4639606 • 4652750 • 4672215 • 4699447
• 4709369 • 4749879 • 4786798 • 4792666 • 4794240 • 4798943 • 4799164 • 4820911 • 4845349 • 4861972 • 4861973 •
4866257 • 4868836 • 4879456 • 4939355 • 4939356 • 4943127 • 4963719 • 4971176 • 4971177 • 4991692 • 5001406 •
5015831 • 5019697 • 5019698 • 5086879 • 5115120 • 5144118 • 5146463 • 5179270 • 5198649 • 5200597 • 5202784 •
5208449 • 5210397 • 5212371 • 5212372 • 5214270 • 5229590 • 5231293 • 5232185 • 5233169 • 5235168 • 5237161 •
5237162 • 5239165 • 5247161 • 5256864 • 5258604 • 5258699 • 5260554 • 5274219 • 5296689 • 5298728 • 5311000 •
5327451 • 5329103 • 5330370 • 5347113 • 5347121 • 5371361 • 5382783 • 5386105 • 5389917 • 5410108 • 5420410 •
5422472 • 5426507 • 5438187 • 5440110 • 5440111 • 5446271 • 5446749 • 5448050 • 5463211 • 5475206 • 5475207 •
5479011 • 5481098 • 5491328 • 5493108 • 5504350 • 5508505 • 5512740 • 5541397 • 5552593 • 5557095 • 5563402 •
5565668 • 5576531 • 5581707 • 5594231 • 5594441 • 5598070 • 5602376 • 5608201 • 5608399 • 5612529 • 5629510 •
5635699 • 5641958 • 5646391 • 5661435 • 5664231 • 5666045 • 5671374 • 5675138 • 5682028 • 5686716 • 5696370 •
5703347 • 5705802 • 5714750 • 5717194 • 5723852 • 5750976 • 5767502 • 5770847 • 5786581 • 5786585 • 5787103 •
5789732 • 5796222 • 5804809 • 5814803 • 5814804 • 5821721 • 5822343 • 5825009 • 5834708 • 5834750 • 5837983 •
5837988 • 5852286 • 5864129 • 5869827 • 5874722 • 5883370 • 5905249 • 5907147 • 5923023 • 5925868 • 5929421 •
5945670 • 5959284 • 5962838 • 5979769 • 6000619 • 6006991 • 6012639 • 6016135 • 6024284 • 6041374 • 6042012 •
6045044 • 6047889 • 6047894 • 6056198 • 6065676 • 6069696 • 6073849 • 6073851 • 6094288 • 6112993 • 6129279 •
6129282 • 6134039 • 6142376 • 6152368 • 6152372 • 6155488 • 6166375 • 6169614 • 6173894 • 6176429 • 6188500 •
6189784 • 6213397 • 6223986 • 6230975 • 6230976 • 6237852 • 6244510 • 6259545 • 6260763 • 6266175 • 6273336 •
6276605 • 6279829 • 6290134 • 6290135 • 6293467 • 6303927 • 6311895 • 6318634 • 6328216 • 6332576 • 6332577 •
6343741 • 6454168 • 6478224 • 6568598 • 6578765 • 6705527 • 6974084 • 6991169 •7051940 • AU703547 • D312631 •
D313590 • D320011 • D320012 • D323492 • D330707 • D330708 • D349109 • D350127 • D350735 • D351149 • D351150
• D352936 • D352937 • D352938 • D352939 • D358588 • D361565 • D372234 • D374630 • D374869 • D375493 •
D376357 • D377345 • D377346 • D377347 • D377348 • D388075 • D446524 • EP0256296 • EP0260155 • EP0260156 •
EP0295936 • EP0325469 • EP0349770 • EP0368254 • EP0442215 • EP0498366 • EP0531645 • EP0663643 •
EP0698251 • GB2252333 • GB2284086 • GB2301691 • GB2304954 • GB2307093 • GB2308267 • GB2308678 •
GB2319103 • GB2333163 • GB2343079 • GB2344486 • GB2345568 • GB2354340 • ISR107546 • ISR118507 •
ISR118508 • JP1962823 • JP1971216 • JP2513442 • JP2732459 • JP2829331 • JP2953593 • JP2964278 • MEX185552 •
MEX187245 • RE37166 • Other Patents Pending
Statement of Agency Compliance
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
FCC Class B Compliance Statement
The user is cautioned that changes or modifications not expressly approved by the part responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio or television technician for help.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits under Specific Absorption Rate
(SAR) tests for portable devices operating closer than 20 cm to nearby persons, set forth in an
uncontrolled environment. The PowerScan 7000BT handheld scanner has been demonstrated to
meet these RF emissions safety limits.
Canadian Notice
This equipment does not exceed the Class B limits for radio noise emissions as described in the
Radio Interference Regulations of the Canadian Department of Communications.
Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables
aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique
edicte par le ministere des Communications du Canada.
Power Supply
Models require either a Listed class II or class III with a Limited Power Source (LPS).
For the safety certification to be valid, class III input power sources must be IEC/EN60950-1
(EN 60335-series, EN 60065 or relevant) approved.
Input: 100 - 240 VAC
Output: 9 - 10 VDC
Max. Current: 2.0 A
Max. Power: 20 W
For4-slot battery charger:
Input: 100 - 240 VAC
Output: 12 VDC
Max. Current: 2.5 A
Max. Power: 30 W
Quick Reference Guide
i
Solids and Water Protection
The Imager is rated as IEC 529-IP65. This nomenclature designates the degree of water and dust
resistance, indicating the imager is totally protected against dust and is protected against low pressure jets of water from all directions - limited ingression permitted.
The Base Station is rated as IEC 529-IP54, indicating the unit is protected against dust, limited
ingress (no harmful deposit) and is protected against water sprayed from all directions - with limited
ingression permitted.
Datalogic Scanning, Inc.
POWERSCAN® END USER LICENSE AGREEMENT
Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to the product’s operation. This Software is being provided to you under license, subject to the terms
and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted
the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or the
Software, and you must contact the party from whom you acquired the Datalogic Product for instructions.
This End User Software License Agreement (“Agreement”) is a legally binding agreement governing the licensing of
the Software and Documentation by Datalogic, Scanning Holdings, Inc. and its wholly owned subsidiaries and affiliates (“Datalogic”) to the entity or person who has purchased or otherwise acquired a Datalogic Product (“End User”).
For purposes of this Agreement, any software that is associated with a separate end-user license agreement is
licensed to you under the terms of that license agreement. Datalogic and End User hereby agree as follows:
1. Definitions.
1.1
1.2
1.3
1.4
"Documentation" means materials such as user’s guides, program reference guides, quick reference guides,
manuals, or similar materials associated with or related to the Datalogic Product, whether in printed, “online”,
or other form.
"Proprietary Information" means: (a) source code, object code, software, documentation, and any related
internal design, system design, data base design, algorithms, technology, technical data or information, implementation techniques, and trade secrets related to the Software, (b) any other trade secrets marked appropriately or identified as proprietary or confidential, and (c) any information that End User, under the
circumstances, should recognize as confidential. Proprietary Information does not include any information that
the receiving party can establish was (1) in the public domain, (2) already in the receiving party’s possession
or rightfully known prior to receipt, (3) rightfully learned from a third party not in violation of any other's proprietary rights, or (4) independently developed without access to Proprietary Information.
“Datalogic Product” means the Datalogic Powerscan® series, Powerscan® Imager series, Powerscan® EP
series, Powerscan® LR series, Powerscan® HD series, and/or Powerscan RF® series scanner and/or scanner/scale product, including all embedded Software in and all Documentation related to such product, which
has been purchased or otherwise acquired by End User, whether obtained directly or indirectly from Datalogic.
"Software" means any software or computer programs of Datalogic or its third party licensors in machine readable form which is embedded in the Datalogic Product, whether obtained directly or indirectly from Datalogic,
including any replacement, update, upgrade, enhancement or modification.
2. Scope Of License Granted.
2.1
2.2
Datalogic grants to End User a non-exclusive, non-transferable, perpetual license to use the Software, solely
on the Datalogic Product in which it is embedded (“designated Datalogic Product”), in machine-readable form
only, solely for End User's internal business purposes. This Agreement does not convey ownership of the
Software to End User. Title to the Software shall be and remain with Datalogic or the third party from whom
Datalogic has obtained a licensed right. As used in this Agreement, the term “purchase” or its equivalents
when applied to the Software shall mean “acquire under license.” End User is not entitled to receipt or use of
the source code to any Software.
End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give,
or otherwise transfer the Software to any other person or organization, for purposes other than as expressly
provided in this Agreement, without Datalogic’s prior written consent.
3. Transfers, Support.
3.1
3.2
3.3
ii
Any copying, installing, reproduction, remanufacture, reverse engineering, electronic transfer, or other use of
the Software on other than the designated Datalogic Product will be a material breach of this Agreement.
However, Datalogic may elect not to terminate this Agreement or the granted licenses, but instead may elect
to notify End User that End User is deemed to have ordered and accepted a license for each breaching use.
End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach.
End User shall not sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Datalogic
Product to any third party unless such third party agrees with Datalogic in writing to be bound by the terms
and conditions of this Agreement. Any such transfer of the Datalogic Product absent such agreement shall be
null and void.
End User may obtain support for Software from Datalogic at Datalogic’s standard support fees and under Datalogic’s standard support terms and conditions in effect at the time the support is requested.
PowerScan® 7000BT SRI
4. Intellectual Property.
End User acknowledges that the Software constitutes valuable trade secrets of Datalogic or Datalogic’s third party
licensors and that the Software is protected by intellectual property laws and treaties. The license set forth in this
Agreement does not transfer to End User any ownership of Datalogic’s or its third party licensors' copyrights, patents,
trademarks, service marks, trade secrets, or other intellectual property rights and End User shall have no right to
commence any legal actions to obtain such rights. End User shall not remove, modify, or take any other action that
would obscure any copyright, trademark, patent marking, or other intellectual property notices contained in or on the
Datalogic Product.
5. Proprietary Information.
5.1
5.2
5.3
End User acknowledges that Proprietary Information is the confidential, proprietary, and trade secret property
of Datalogic and Datalogic’s third party licensors and End User acquires no right or interest in any Proprietary
Information.
End User shall not disclose, provide, or otherwise make available the Proprietary Information of Datalogic or
its third party licensors to any person other than End User’s authorized employees or agents who are under
confidentiality agreement, and End User shall not use the Proprietary Information other than in conjunction
with use of the Datalogic Product exclusively for End User’s internal business purposes. End User shall take
steps to protect the Proprietary Information no less securely than if it were End User's own intellectual property.
The provisions of this Proprietary Information Section shall survive and continue for five (5) years after the termination of this Agreement.
6. Limited Warranty.
6.1
6.2
Datalogic warrants that, under normal use and operation, the Datalogic Product will conform substantially to
the applicable Documentation for the period specified in the Documentation. During this period, for all reproducible nonconformities for which Datalogic has been given written notice, Datalogic will use commercially
reasonable efforts to remedy nonconformities verified by Datalogic. End User agrees to supply Datalogic with
all reasonably requested information and assistance necessary to help Datalogic in remedying such nonconformities. For all defects reported to Datalogic within the warranty period, Datalogic’s liability is limited to providing End User with one copy of corrections or responding to End User's problem reports according to
Datalogic's standard assistance practices. Datalogic does not warrant that the product will meet End User's
requirements or that use of the product will be uninterrupted or error free, or that Datalogic's remedial efforts
will correct any nonconformance. This limited warranty does not cover any product that have been subjected
to damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in any manner other
than as established in the Documentation, or if End User breaches any of the provisions of this Agreement.
EXCEPT AS PROVIDED IN THIS AGREEMENT, THE DATALOGIC PRODUCT IS PROVIDED “AS IS” AND
DATALOGIC MAKES NO WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, WRITTEN OR ORAL,
WITH RESPECT TO THE PRODUCT, AND SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
7. Infringement.
7.1
7.2
7.3
7.4
Datalogic will defend End User against any claim in a lawsuit that the Datalogic Product furnished hereunder
infringe a United States patent or copyright of a third party and Datalogic will pay any damages finally
awarded against End User by a court of competent jurisdiction that are attributable to such claim or will pay
End User’s part of any settlement that is attributable to such claim, provided, that 1) End User notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End
User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent to
Datalogic Scanning, Inc., Legal Department, 111 SW Fifth Ave. Suite 4100, Portland, OR 97204-3644.
In the defense or settlement of any such claim, Datalogic may, at its option, 1) procure for End User the right
to continue using the Datalogic Product, 2) modify the Datalogic Product so that it becomes non-infringing,
3) replace the Datalogic Product with an equivalent product not subject to such claim, or 4) provide End User
an opportunity to return the Datalogic Product and receive a refund of the purchase price paid, less a reasonable allowance for use.
Datalogic shall have no liability to End User for claims of infringement based upon 1) the use of any Datalogic
Product in combination with any product which Datalogic has not either furnished or authorized for use with
such Datalogic Product 2) the use of any Datalogic Product designed, manufactured, or modified to the specifications of End User, or 3) End User’s modification of the Datalogic Product without written authorization
from Datalogic.
THE FOREGOING STATES DATALOGIC’S COMPLETE AND ENTIRE OBLIGATION CONCERNING
CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS
AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER
ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES.
8. Limitation Of Liability.
EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END
USER BY ANY OTHER PARTY. IN NO EVENT SHALL DATALOGIC'S LIABILITY FOR DAMAGES, IF ANY,
WHETHER BASED UPON CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, STRICT LIABILITY, WARRANTY, OR ANY OTHER BASIS, EXCEED THE PRICE OR FEE PAID BY END USER FOR THE DATALOGIC PRODUCT. UNDER NO CIRCUMSTANCES SHALL DATALOGIC BE LIABLE TO END USER OR ANY
THIRD PARTY FOR LOST PROFITS, LOST DATA, INTERRUPTION OF BUSINESS OR SERVICE, OR FOR ANY
OTHER SPECIAL, CONSEQUENTIAL, CONTINGENT, INDIRECT, INCIDENTAL, PUNITIVE, EXEMPLARY, OR
OTHER SIMILAR DAMAGES, EVEN IF DATALOGIC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
9. Government Restricted Rights; International Use.
9.1
Use, duplication, or disclosure of the Software by the U.S. Government is subject to the restrictions for com-
Quick Reference Guide
iii
9.2
puter software developed at private expense as set forth in the U.S. Federal Acquisition Regulations at FAR
52.227-14(g), or 52.227-19 or in the Rights in Technical Data and Computer Software clause at DFARS
252.227-7013(c)(1)(ii), whichever is applicable.
If End User is using the Datalogic Product outside of the United States, End User must comply with the applicable local laws of the country in which the Datalogic Product is used, with U.S. export control laws, and with
the English language version of this Agreement. The provisions of the “United Nations Convention on International Sale of Goods” shall not apply to this Agreement.
10. Termination.
10.1
10.2
Either party may terminate this Agreement or any license granted under this Agreement at any time upon written notice if the other party breaches any provision of this Agreement.
Upon termination of this Agreement, End User immediately shall cease using any non-embedded software
and shall return to Datalogic or destroy all non-embedded software covered by this Agreement, and shall furnish Datalogic with a certificate of compliance with this provision signed by an officer or authorized representative of End User. For embedded software, End User agrees to sign a waiver prepared by Datalogic
concerning further use of the embedded Software. End User’s resumed or continued use of the embedded
Software after termination shall constitute End User’s agreement to be bound by the terms and conditions of
this Agreement for such use.
11. General Provisions.
11.1
11.2
11.3
11.4
11.5
Entire Agreement; Amendment. This document contains the entire agreement between the parties relating to
the licensing of the Software and supersedes all prior or contemporaneous agreements, written or oral,
between the parties concerning the licensing of the Software. This Agreement may not be changed,
amended, or modified except by written document signed by Datalogic.
Notice. All notices required or authorized under this Agreement shall be given in writing, and shall be effective
when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Administration, Datalogic Scanning Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be
specified by Datalogic in writing.
Waiver. A party’s failure to enforce any of the terms and conditions of this Agreement shall not prevent the
party’s later enforcement of such terms and conditions.
Governing Law; Venue:This Agreement and the rights of the parties hereunder shall be governed by and construed in accordance with the laws of the State of Oregon U.S.A, without regard to the rules governing conflicts of law. The state or federal courts of the State of Oregon located in either Multnomah or Lane counties
shall have exclusive jurisdiction over all matters regarding this Agreement, except that Datalogic shall have
the right, at its absolute discretion, to initiate proceedings in the courts of any other state, country, or territory
in which End User resides, or in which any of End User's assets are located.
Attorneys’ Fees. In the event an action is brought to enforce the terms and conditions of this Agreement, the
prevailing party shall be entitled to reasonable attorneys’ fees, both at trial and on appeal.
- END -
Software Product Policy
Datalogic reserves the right to ship its products with the latest version of software/firmware available. This provides our customers with the very latest in Datalogic software technology.
The only exception to this policy is when the buyer has a signed contract with Datalogic that clearly
defines the terms and conditions for making software/firmware changes in products shipped to the
buyer.
Laser Cautions
The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S.
to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC
60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous. Laser
pointer models of the imager contain a Visible Laser Diode (VLD) at a wavelength of 655 nanometers and is designed so that there can be no human access to harmful levels of laser light during normal operation, user maintenance, or during prescribed service operations. See the User Manual for
laser pointer configuration information and bar codes.
Do not attempt to open or otherwise service any components in the
optics cavity. Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations.
CAUTION
iv
PowerScan® 7000BT SRI
Table of Contents
Statement of Agency Compliance ............................................................ i
FCC Class B Compliance Statement ................................................... i
FCC RF Radiation Exposure Statement ......................................... i
Canadian Notice ............................................................................. i
Power Supply ................................................................................. i
Solids and Water Protection ............................................................ ii
Software Product Policy ....................................................................... iv
Laser Cautions ............................................................................. iv
Getting Started ................................................................................... 1
Installing the Battery Pack .............................................................. 1
Verifying Scanner Operation Before Linking to the Base Station ........... 3
Connection ................................................................................... 4
Linking the Scanner to a Base Station .............................................. 5
Linking the Scanner to a Bluetooth Device ........................................ 7
Battery Pack Charging and Maintenance ........................................... 7
Programming ................................................................................ 8
Interface Selection ................................................................... 9
Resetting the Standard Product Defaults ......................................... 13
How to Scan ..................................................................................... 14
Troubleshooting ................................................................................ 15
Troubleshooting the RF System ..................................................... 15
Troubleshooting the Scanner ......................................................... 16
Quick Reference Guide
v
NOTES
vi
PowerScan® 7000BT SRI
Getting Started
Installing the Battery Pack
To charge the Battery Pack, See “Battery Pack
Charging and Maintenance” on page 7.
NOTE
WARNING
Datalogic recommends annual replacement of
rechargeable battery packs to ensure maximum
performance.
Do not discharge the battery using any device except for the scanner. When the battery is used in devices other than the linear imager,
it may damage the battery or reduce its life expectancy. If the device
causes an abnormal current to flow, it may cause the battery to
become hot, explode or ignite and cause serious injury.
Lithium-ion battery packs may get hot, explode or ignite and cause
serious injury if exposed to abusive conditions. Be sure to follow the
safety warnings listed below:
• Do not place the battery pack in fire or heat.
• Do not connect the positive terminal and negative terminal of
the battery pack to each other with any metal object (such as
wire).
• Do not carry or store the battery pack together with metal
objects.
• Do not pierce the battery pack with nails, strike it with a hammer, step on it or otherwise subject it to strong impacts or
shocks.
• Do not solder directly onto the battery pack.
• Do not expose the battery pack to liquids, or allow the battery
to get wet.
In the event the battery pack leaks and the fluid gets into your eye,
do not rub the eye. Rinse well with water and immediately seek medical care. If left untreated, the battery fluid could cause damage to
the eye.
Quick Reference Guide
1
Always charge the battery at 32° – 113°F (0° - 45°C) temperature
range.
CAUTION
Use only the authorized power supplies, battery pack, chargers, and
docks supplied by your Datalogic reseller. The use of any other
power supplies can damage the linear imager and void your warranty.
Do not disassemble or modify the battery. The battery contains
safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.
Do not place the battery in or near fire, on stoves or other high temperature locations.
Do not place the battery in direct sunlight, or use or store the battery
inside cars in hot weather. Doing so may cause the battery to generate heat, explode or ignite. Using the battery in this manner may also
result in a loss of performance and a shortened life expectancy.
Do not place the battery in microwave ovens, high-pressure containers or on induction cookware.
Immediately discontinue use of the battery if, while using, charging
or storing the battery, the battery emits an unusual smell, feels hot,
changes color or shape, or appears abnormal in any other way.
Orient the Battery Pack as shown in Figure 1, then push it into the scanner until the alignment pins engage and the unit snaps into place (the
pins will not engage if the Battery Pack is incorrectly oriented). To
remove the Battery Pack, push in on the release latches on either side of
its base and pull it straight out of the scanner.
2
PowerScan® 7000BT SRI
Getting Started
Figure 1. Battery Pack Installation & Removal
Scanner
Alignment Pins
Battery
Pack
Release Latch
Release Latch
Verifying Scanner Operation Before Linking
to the Base Station
Once a charged Battery Pack has been installed in the scanner, scan a
good sample bar code of the symbology1 type your scanner is programmed to read. If unsure how to do this, see the section on How to
Scan in this manual. Tip: The part number bar code on the back cover
of this manual is a Code 39 symbology sample.
The system may signal with one or a combination of indicators depending upon how the scanner and Base Station are programmed to respond
(see LED and Beeper Indications for details). If your scanner fails to read
a sample bar code of a symbology it is programmed to read, turn to the
section titled, Troubleshooting.
1. To enable more bar code symbology types, reference the Product Reference Guide
(PRG).
Quick Reference Guide
3
Connection
shows how to connect the Base Station to a terminal, PC or
other host device. Turn off the host before connection and consult the
manual for that equipment (if necessary) before proceeding.
Figure 2
Base Station Connection and Routing — Fully insert the Power
Cable and Interface (I/F) Cable connectors into their respective ports in
the underside of the Base Station (see Figure 2). Alternatively, you can
either loop the cables around the routing clips and back through the
routing channel to the front of the Base Station as shown, or the cables
can be fed directly out the back of the Base Station via the routing clips.
Optional Power Connection — Plug the AC Adapter into an
approved AC wall socket with the cable facing downwards (as shown in
to prevent undue strain on the socket.
Figure 2)
CAUTION
This Base Station MUST be used with a Datalogic approved power
supply. It is not designed to obtain its power off of the terminal
(POT). Connection to a host terminal without first connecting the
external power supply may result in damage to the terminal.
Figure 2. Connecting the Base Station
Power Cable
I/F
Cable
Routing
Channel
Routing
Clips
Bottom of Base Station
I/F Cable
Optional
AC Adapter
Base
Station
4
Power Cable
PowerScan® 7000BT SRI
Getting Started
Host Connection — The interface type was specified at the time your
scanner was ordered, however you should verify before connection that
the scanner’s cable type is compatible with your host equipment. Most
connections plug directly into the host device as shown in Figure 3. Keyboard Wedge interface cables have a ‘Y’ connection where its female end
mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.
B
Figure 3. Connecting to the Host
23
2
or...
or...
b
ed oar
ge d
or...
M
R
S-
K ey
W
US
IB
Linking the Scanner to a Base Station
To link a scanner to a Base Station, press the Link Button on the Base
Station (see Figure 4) for at least one second to place the base in "Link
Mode"then scan the “Link to a Base Station” bar code below or the link
bar code located on the Base Station itself using the scanner to be linked.
Allow the system several seconds to create the association between the
two units and exit Link Mode. A successful link is indicated by three
Quick Reference Guide
5
ascending tones from the scanner. A “high-low-high-low” tone indicates
the link attempt was unsuccessful. A single LED flash during this tone
indicates no Base Station was discovered. Two green LED flashes during
this tone indicates that more than one Base Station was discovered and
the scanner did not link.
Link to a Base Station
Figure 4. Labeling and Nomenclature
This illustration shows label placement ONLY.
For actual regulatory, patent and other applicable
information, view the labels on the product intself,
or call your nearest sales or service office.
Antenna
Link Bar Code
Scanner
Link
Button
Scan
Window
Amber LED
Trigger
Green
LED
S/N and Laser Safety Label
Indicator
LEDs
Speaker
Port
Battery Pack
Battery Latch
6
Scanner
Latch
Regulatory
Label
Base Station
PowerScan® 7000BT SRI
Getting Started
Linking the Scanner to a Bluetooth Device
A scanner can optionally be linked to a PC with a Bluetooth radio
installed.
1. Ensure that the Bluetooth device and its driver are installed on the
PC.
2. On the PC, open the control window for the Bluetooth device
(usually called “My Bluetooth Places”). Follow the instructions for
the Bluetooth device to disable the security setting for the Bluetooth serial port.
3. Scan the “Link to a PC” bar code below.
Link to a PC
4. On the PC, search for Bluetooth devices that are in range and
select the “Datalogic PS7000 Scanner.”
5. Connect with the serial port for the Datalogic PS7000 Scanner.
Note which serial port number is assigned to the scanner.
6. Open your serial port application and connect to the scanner using
the serial port that was assigned in the previous step.
Battery Pack Charging and Maintenance
The Amber LED will blink twice when a bar code is
decoded when the battery is getting low.
NOTE
Seat the scanner (with installed Battery Pack) in a powered Base Station
as shown in Figure 5, ensuring the Battery Pack is fully seated and
engages the station’s metal contacts. The scanner will sound a short
“chirp” when good contact is made and the green LED on the Base Station should flash, indicating the battery is charging. Alternatively, multiple Battery Packs can be charged external to the scanner using an
accessory charging unit available from your Datalogic dealer.
Quick Reference Guide
7
There presently are no US, North America or World disposal requirements for Lithium-Ion batteries such as the Battery Pack, so when they
won't hold a charge anymore they can be disposed of; preferably through
a recycling center. Contact your local government for disposal or recycling practices in your area.
Figure 5. Charging the Battery Pack in a Docked Scanner
Programming
The scanner is typically factory-configured with a set of default features
standard to the interface type you ordered. You can select other options
and customize your scanner through use of the instructions and programming bar codes available in the Product Reference Guide (PRG).
You can view and download this and other manuals from the website
listed on the back cover of this manual.
8
PowerScan® 7000BT SRI
Getting Started
Interface Selection
Select the desired interface by scanning the associated bar code below.
For Keyboard Wedge interfaces, see Table 1-1 for a listing of associated
keyboard types.
INTERFACE
SELECTION BARCODE
RS-232
Standard
RS-232
Wincor-Nixdorf
Wand
Emulation
IBM 4683
Port 5B
IBM 4683
Port 9B
IBM 4683
Port 17
Quick Reference Guide
9
INTERFACE
SELECTION BARCODE
IBM USB
USB HID
Keyboard
USB HID POS
Table 1-1. Keyboard Wedge Interface Reference
I/F Type
PCs Supported
A
PC/XT w/Alternate Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key
B
Encoding
C
PS/2 25 and 30 w/Alternate Key Encoding
D
PC/XT w/Standard Key Encoding
AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key
E
Encoding
F
PS/2 25 and 30 w/Standard Key Encoding
G
IBM 3xxx w/122 keyboard
H
IBM 3xxx w/102 keyboard
I
PS/55 5530T w/104 keyboard
J
NEC 9801
K
WYSE 30/30+ WY-30 Keyboard 83 Keys
WYSE 60/85/99 GT/150/160/285 Style IBM Enhanced PC, 520/520ES
L
Style IBM Enhanced PC FR
WYSE 55/65/65 ES/120/185/325 Style IBM Enhanced PC
WYSE 60/85/99 GT/150/160/285 ANSI Keyboard 105 Keys, 520/520 ES
M
ANSI Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI Keyboard 105 Keys
WYSE 60/85/99 GT/150/160/285 ASCII Kbd, 520/520 ES ASCII Kbd
N
WYSE 55/65/65 ES/120/185/325 ASCII Keyboard
WYSE 60/85/99 GT/150/160/285 ANSI W285 Keyboard 105 Keys, 520/
O
520 ES ANSI W285 Keyboard 105 Keys
WYSE 55/65/65 ES/120/185/325 ANSI W285 Keyboard 105 Keys
P
WYSE WINTERM 3320 SE
10
PowerScan® 7000BT SRI
Getting Started
Q
R
S
T
U
V
W
X
IBM 3153
IBM 316X, 3179/3180/319X/3270
IBM 3151/3152-010, 347X/348X
DIGITAL VT 220/320/330/340/350/382
DIGITAL VT420
DIGITAL VT 510/520 IBM ANSI Style Keyboard
DIGITAL VT 510/520 IBM PC Style Keyboard
SUN SPARC 5/10
SUN 420/440, ITX
Reference the Product Reference Guide (PRG) for
more information about keyboard support.
NOTE
Keyboard
Wedge A
Keyboard
Wedge B
Keyboard
Wedge C
Keyboard
Wedge D
Keyboard
Wedge E
Keyboard
Wedge F
Keyboard
Wedge G
Quick Reference Guide
11
Keyboard
Wedge H
Keyboard
Wedge I
Keyboard
Wedge J
Keyboard
Wedge K
Keyboard
Wedge L
Keyboard
Wedge M
Keyboard
Wedge N
Keyboard
Wedge O
Keyboard
Wedge P
Keyboard
Wedge Q
Keyboard
Wedge R
12
PowerScan® 7000BT SRI
Getting Started
Keyboard
Wedge S
Keyboard
Wedge T
Keyboard
Wedge U
Keyboard
Wedge V
Keyboard
Wedge W
Keyboard
Wedge X
Resetting the Standard Product Defaults
If programming settings for your scanner are in an unknown condition,
factory settings can be restored by scanning the “Standard Product
Default Settings” bar code below. A listing of factory default settings is
available in the PRG. Settings can vary, depending upon the interface
type.
Standard Product Default Settings
Quick Reference Guide
13
How to Scan
When the trigger is pressed, the scanner projects a red, horizontal illuminating beam. This beam will remain on until the trigger is released, a bar
code is read, or until a time-out1 period expires.
NOTE
If the surface being scanned is highly reflective
(e.g., laminated), it may be necessary to tilt the item
or the scanner slightly (15° to 18°) to prevent
unwanted reflection.
Linear Bar Codes — To scan a linear bar code, center the illumination
beam over the bar code as shown in Figure 6a. The scanner must “see”
across the width of all of the bars. Move the scanner further away from
the bar code to increase the scanning coverage area.
Stacked Bar Codes — Stacked bar codes are read by holding in on the
trigger and moving the illumination beam in a smooth motion over the
bar code from top to bottom as shown in Figure 6b. That motion should
be slow as well, since moving very fast will cause individual rows of the
stacked code to be overlooked, and will require extra sweeps to capture.
You will hear a series of ticks, followed by a final beep when the bar
code’s content has been completely decoded. You may need to sweep the
bar code several times in order to complete the read. Sweeps may be
made either from top-to-bottom or bottom-to-top.
1. Reference the Product Reference Guide (PRG) for more information about the aiming
beam time-out period.
14
PowerScan® 7000BT SRI
Troubleshooting
Figure 6. Scanning Bar Codes
a
Decrease...
...or Increase distance
from bar code to adjust
aiming beam width to
cross all bars.
b
Stacked
Sweep stacked bar codes
slowly and smoothly from
top to bottom (or bottom to top).
Troubleshooting
Troubleshoot your scanning system by performing the following checks:
Troubleshooting the RF System
For the RF system, ensure...
•
the battery is charged. See "Battery Pack Charging and
Maintenance" on page 7.
•
the battery is properly installed. See "Installing the Battery Pack" on
page 1.
Quick Reference Guide
15
•
the scanner is linked to the desired Base Station. See "Linking the
Scanner to a Base Station" on page 5.
•
the scanner is within reasonable operating range of the Base Station, with no major obstructions between the radio units such as
thick walls or heavy machinery. (At the time of this writing, maximum scanner-to-Base Station range is specified at 100 meters.)
•
the Base Station is powered-on. When the Base Station powers up,
both LEDs briefly flash. If both lights are bright and crisp, this is a
good indication of adequate power input from the AC Adapter.
•
the Base Station interface cable is securely attached to the host.
Consult your technical support manager or refer to your host system manual to identify the proper cable connection for the scanner. If necessary, verify interface cable function by using a knowngood interface cable.
Troubleshooting the Scanner
If the problem is specific to scanning, verify that...
•
The scanner will automatically perform a set of self-tests whenever
you turn it on. Observe and note any special indications made by
the scanner (an unexpected pattern of flashes or beeps) during
power-up. If technical support is contacted regarding a problem,
they may request this information.
•
Does the scanner power on? Does the illumination beam come on?
If no illumination beam, check that...
• the battery has been adequately charged.
• the battery is fully seated and its latch engaged.
• the trigger works.
•
Is the scanner having trouble reading your symbols?
If the scanner isn’t reading symbols well, check that the symbols...
• aren’t smeared, rough, scratched, or exhibiting voids.
• aren’t coated with frost or water droplets on the surface.
16
PowerScan® 7000BT SRI
Troubleshooting
• are enabled in the scanner. See the Product Reference Guide
(PRG) for more about configuring the scanner to read symbologies).
•
Is the bar code displayed but not entered?
The bar code is displayed on the host device correctly, but you still
have to press a key to enter it (the Enter/Return or Tab key, for
example).
You need to program a suffix which enables the scanner to output
the bar code data plus the key you need (such as a carriage return
“CR”) to enter the data into your application. Refer to the PRG
for further information.
•
Does the scanner read the bar code incorrectly?
If the scanner reads a bar code, but the data is not displayed correctly on the host screen:
• The scanner may not be programmed for the appropriate terminal interface. For example, you scan “12345” and the host displays “@es%.” Reprogram the scanner with the correct interface
selection bar code. See the Product Reference Guide (PRG).
• The scanner may not be programmed to output your bar code
data properly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the scanner with the proper Data
Editing selections. Reference the PRG.
•
The scanner won’t read your bar code at all.
• Scan the part number bar code on the back of this manual or
other known-good bar code samples. If the scanner reads sample
bar codes, check that your target bar code is readable.
• Verify that your bar code symbology is enabled. See the PRG.
•
If you aren’t sure what programming options have been set in the
scanner, or if you want the factory default settings restored, go to
the Resetting the Standard Product Defaults section of this manual
and scan the standard factory default settings bar code.
Quick Reference Guide
17
•
The scanner sounds other than a standard “Good Read” beep followed by an “Acknowledge1” beep when reading a bar code (indicating the bar code has been read and properly transmitted).
• Verify the scanner is linked to and within range of its Base Station.
1. Typically, both of these beep indications are active in the scanner. To enable/disable these
indications, reference the PRG.
18
PowerScan® 7000BT SRI
DECLARATION OF CONFORMITY
Datalogic hereby declares that the Equipment specified below has been
tested and found compliant to the following Directives and Standards:
Directives: EMC 89/336/EEC
Low Voltage 73/23/EEC
R&TTE 1999/5/EC
Standards: EN 55022-B:A2/2003 - Generic Emissions
CISPR 22-B:2005 - Generic Emissions
EN 55024/A2:2003 - Generic Immunity – ITE
EN 301 489-17:2002 – Radio Immunity
EN 300 328: 2004 - Radio
EN 60950-1:2001 - ITE Safety
EN 60825-1/A2:2002 - Laser Safety
UL 1642, UL 2054, UN 38.3 – Li-ion Battery Pack
Equipment Type: Barcode Scanning Equipment
Products: PowerScan 7000BT family with Dock
Placed into EU Service: April 2007 under the Datalogic trademark. October 2006 under the PSC trademark.
Responsible
Datalogic Scanning, Inc. 959 Terry St. Eugene, OR USA
Manufacturer:
Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC
English: This equipment is in compliance with the essential requirements & other relevant provisions
Directive 1999/5/EC.
Nederlands: Deze apparatuur voldoet aan de essentiële vereisten en andere relevante voorzieningen va
EU-richtlijn 1999/5/EC.
Suomalainen: Tämä laite noudattaa direktiivin 1999/5/EC keskeisiä vaatimuksia ja sen muita olennaisia
määräyksiä.
Français: Cet équipement répond aux exigences et provisions de la Directive 1999/5/EC.
Deutsch: Diese Geräte entsprechen den Anforderungen und anderen relevanten Bestimmungen der
Richtlinie 1999/5/EC.
Italiano: Questa apparecchiatura rispetta i requisiti essenziali e le altre clausole rilevanti della Dirett
1999/5/CE.
Dansk: Dette utstyret er i samsvar med de grunnleggende kravene og andre relevante forskrifter i
1999/5/EC-direktivet.
Português: Este equipamento está de acordo com os requisitos essenciais e outras provisões relevant
da Diretiva 1999/5/EC.
Español: Este equipo cumple con los requisitos esenciales y otras provisiones relevantes de la Dire
tiva 1999/5/EC.
Svenska: Denna utrustning uppfyller de väsentliga kraven och andra relevanta förordningar i Direktiv
1999/5/EC.
Norsk: Dette utstyret er i samsvar med de grunnleggende krav og andre relevante bestemmelser
EU-direktiv 1999/5/EF
lslenska: Þetta taeki er samkvaemnt grunnkröfum og öðrum viðeigandi ákvaðum Tilskipunar 1999/5
CE.
Australia
Japan
Datalogic Scanning Pty Ltd
North Ryde, Australia
Telephone: [61] (2) 9870 3200
Fax: [61] (2) 9878 8688
Datalogic Scanning KK
Shinagawa, Tokyo, Japan
Telephone: 81 (0)3 3491 6761
Fax: 81 (0)3 3491 6656
France and Benelux
Latin America
Datalogic Scanning Sarl
LES ULIS Cedex, France
Telephone: [33].01.64.86.71.00
Fax: [33].01.64 46.72.44
Datalogic Scanning, Inc
Miami, Florida, USA
Telephone: (305) 591-3222
Fax: (305) 591-3007
Germany
Spain and Portugal
Datalogic Scanning GmbH
Darmstadt, Germany
Telephone: 49 (0) 61 51/93 58-0
Fax: 49 (0) 61 51/93 58 58
Datalogic Scanning Sarl Sucursal en España
Madrid, Spain
Telephone: 34 91 746 28 60
Fax: 34 91 742 35 33
Italy
United Kingdom
Datalogic Scanning SpA
Vimercate (MI), Italy
Telephone: [39] (0) 39/62903.1
Fax: [39] (0) 39/6859496
Datalogic Scanning LTD
Watford, England
Telephone: 44 (0) 1923 809500
Fax: 44 (0) 1923 809 505
www.scanning.datalogic.com
Datalogic Scanning, Inc.
959 Terry Street
Eugene, OR 97402
Telephone: (541) 683-5700
Fax: (541) 345-7140
©2007 Datalogic Scanning, Inc.
R44-2708 (Rev. B)
5/07