Philips 32PFL5609D/30 User manual

Register your product and get support at
www.philips.com/welcome
42PFL7409D/30
47PFL7409D/30
32PFL5609D/30
42PFL5609D/30
47PFL5609D/30
*non-contractual image
EN User manual
26
26
27
27
28
28
30
Back connectors
Side connectors
Connect a computer
Assign devices
Use Philips EasyLink
Use a Kensington lock
1 Notice
2
2 Important
3
3 Your product
5
5
5
8 Product information
31
9 Troubleshooting
33
7
7
7
8
8
10 Index
35
Side controls and indicators
Remote control
4 Use your product
Switch your TV on/off or to standby
Switch channels
Watch connected devices
Adjust TV volume
5 Use your product in digital mode
Understand the information banner
Install channels
Test digital reception
Change the order of stored channels
Set your preferences
Control access to digital channels
Set up your favourite channels
Use the Electronic Programme Guide
9
9
9
10
11
11
12
14
14
6 Use your product in analogue mode 15
Access TV menus
15
Change picture and sound settings
16
Create and use lists of favourite channels 18
Use timers
19
Use child control
20
Use subtitles
20
Use the TV clock
21
View photos, play music and watch video
from a USB storage device
21
Use Scenea to display a picture as TV
wallpaper
23
Update the TV software
23
Change TV preferences
24
Start a TV demo
24
Reset the TV to factory settings
25
EN
1
E n glish
7 Connect devices
Contents
1 Notice
2009 © Koninklijke Philips Electronics N.V. All
rights reserved.
Specications are subject to change without
notice. Trademarks are the property of
Koninklijke Philips Electronics N.V. or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other than
those specied herein, conrmation of their
validity and suitability must be obtained. Philips
warrants that the material itself does not
infringe any United States patents. No further
warranty is expressed or implied.
Philips cannot be held responsible either for any
errors in the content of this document or for
any problems as a result of the content in this
document. Errors reported to Philips will be
corrected and published on the Philips support
website as soon as possible.
Pixel characteristics
This LCD product has a high number of
colour pixels. Although it has effective pixels of
99.999% or more, black dots or bright points of
light (red, green or blue) may appear constantly
on the screen. This is a structural property of
the display (within common industry standards)
and is not a malfunction.
Warranty
No components are user serviceable. Do not
open or remove covers to the inside of the
product. Repairs may only be done by Philips
Service Centres and ofcial repair shops. Failure
to do so shall void any warranty, stated or
implied.
Any operation expressly prohibited in
this manual, any adjustments, or assembly
2
EN
procedures not recommended or authorised in
this manual, shall void the warranty.
Compliance with EMF
Koninklijke Philips Electronics N.V. manufactures
and sells many products targeted at consumers
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
One of Philips’ leading Business Principles is to
take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing the products.
Philips is committed to develop, produce and
market products that cause no adverse health
effects. Philips conrms that if its products are
handled properly for their intended use, they
are safe to use according to scientic evidence
available today.
Philips plays an active role in the development
of international EMF and safety standards,
enabling Philips to anticipate further
developments in standardisation for early
integration in its products.
Copyright
All other registered and unregistered
trademarks are the property of their respective
owners.
® Kensington and Micro Saver are registered
US trademarks of ACCO World Corporation
with issued registrations and pending
applications in other countries throughout the
world.
VESA, FDMI and the VESA Mounting Compliant
logo are trademarks of the Video Electronics
Standards Association.
Portions of this software are copyright © The
FreeType Project (www.freetype.org).
•
Read and understand all instructions before you
use your TV. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
•
Risk of electric shock or re!
• Never expose the TV to rain or
water. Never place liquid containers,
such as vases, near the TV. If
liquids are spilt on or into the TV,
disconnect the TV from the power
outlet immediately. Contact Philips
Consumer Care to have the TV
checked before use.
• Never place the TV, remote control
or batteries near naked ames or
other heat sources, including direct
sunlight.
To prevent the spread of re, keep
candles or other ames away from
the TV, remote control and batteries
at all times.
•
•
•
Never insert objects into the
ventilation slots or other openings on
the TV.
• When the TV is swivelled ensure
that no strain is exerted on the
power cord. Strain on the power
cord can loosen connections and
cause arcing.
Risk of short circuit or re!
• Never expose the remote control or
batteries to rain, water or excessive
heat.
•
•
Avoid force coming onto power
plugs. Loose power plugs can cause
arcing or re.
Risk of injury or damage to the TV!
• Two people are required to lift and
carry a TV that weighs more than
25 kg.
• When stand mounting the TV, use
only the supplied stand. Secure the
stand to the TV tightly. Place the
TV on a at, level surface that can
support the combined weight of the
TV and the stand.
• When wall mounting the TV, use
only a wall mount that can support
the weight of the TV. Secure the wall
mount to a wall that can support the
combined weight of the TV and wall
mount. Koninklijke Philips Electronics
N.V. bears no responsibility for
improper wall mounting that result in
accident, injury or damage.
Risk of injury to children! Follow these
precautions to prevent the TV from
toppling over and causing injury to
children:
• Never place the TV on a surface
covered by a cloth or other material
that can be pulled away.
• Ensure that no part of the TV hangs
over the edge of the surface.
• Never place the TV on tall furniture
(such as a bookcase) without
anchoring both the furniture and TV
to the wall or a suitable support.
• Educate children about the dangers
of climbing on furniture to reach the
TV.
Risk of overheating! Never install the TV
in a conned space. Always leave a space
of at least 4 inches or 10 cm around the
TV for ventilation. Ensure curtains or
other objects never cover the ventilation
slots on the TV.
Risk of damage to the TV! Before you
connect the TV to the power outlet,
ensure that the power voltage matches
EN
3
E n glish
•
2 Important
•
•
•
•
•
•
the value printed on the back of the TV.
Never connect the TV to the power
outlet if the voltage is different.
Risk of injury, re or power cord damage!
Never place the TV or any objects on the
power cord.
To easily disconnect the TV power cord
from the power outlet, ensure that you
have full access to the power cord at all
times.
When you disconnect the power cord,
always pull the plug, never the cable.
Disconnect the TV from the power outlet
and aerial before lightning storms. During
lightning storms, never touch any part of
the TV, power cord or aerial cable.
Risk of hearing damage! Avoid using
earphones or headphones at high
volumes or for prolonged periods of time.
If the TV is transported in temperatures
below 5°C, unpack the TV and wait
until the TV temperature matches room
temperature before connecting the TV to
the power outlet.
Screen care
•
•
•
•
•
4
Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
Unplug the TV before cleaning.
Clean the TV and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
Risk of damage to the TV screen! Never
touch, push, rub or strike the screen with
any object.
To avoid deformations and colour fading,
wipe off water drops as soon as possible.
EN
Recycling
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheeled bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences for the
environment and human health.
Remote control
E n glish
3 Your product
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers; register your product
at www.philips.com/welcome.
28
1
2
27
3
26
Side controls and indicators
25
24
4
4
5
6
7
8
9
3
23
2
1
a
POWER: Switches the product on
or off. The product is not powered
off completely unless it is physically
unplugged.
22
16
17
18
b P/CH +/-: Switches to the next or
previous channel.
c
10
11
12
13
14
15
19
SOURCE: Selects connected devices.
d VOLUME +/-: Increases or decreases
volume.
21
a
20
(Standby-On)
• Switches the TV to standby if it is on.
• Switches on the TV if it is in standby.
EN
5
b DIGITAL MENU
Accesses or exits the digital menu.
s 0-9 (Numeric buttons)
Selects a channel or setting.
c
t
PICTURE (Smart picture)
Launches the picture menu.
d SUBTITLE
Enables or disables subtitles.
u
SOUND (Smart Sound)
Launches the sound menu.
e DUAL
Switches Stereo and Nicam Stereo to
Mono. Selects rst language (Dual I)
or second language (Dual II) in bilingual
programmes.
v
+/- ( Volume +/-)
Increases or decreases volume.
w
BACK A/CH
Returns to a previous screen.
Toggles between the current channel and
the last viewed channel.
x
GUIDE
Toggles the Electronic Programme
Guide (EPG) on or off. Enabled on digital
channels only.
f
g
SOURCE
Selects connected devices.
(Home)
Toggles the home menu on or off.
OPTIONS
Accesses options relating to the current
activity or selection.
h OK
Conrms an entry or selection.
y SCENEA ( Wallpaper)
Displays wallpaper on your TV screen.
i
(Navigation buttons)
Navigates through the menus.
j
INFO
Displays programme information, if
available.
z DEMO
Toggles the demonstration menu on or
off.
k
(Backward)
Searches backward.
l
(Forward)
Searches forward.
m
(Play/Pause)
Starts, pauses or resumes disc play.
n
(Record)
Starts or stops video recording.
o
(Stop)
Stops disc play.
p
(Mute)
Mutes or restores audio output.
q CH +/- (Channel +/-)
Switches to the next or previous channel.
r
FORMAT
Selects a picture format.
6
EN
{ TV
Switches back to the antenna source from
EasyLink mode.
| ANALOG/DIGITAL
Selects between analog or digital mode.
Switch channels
E n glish
4 Use your product
This section helps you perform basic operations.
Switch your TV on/off or to
standby
•
To switch on
• If the standby indicator is off, press
POWER at the side of the TV.
• If the standby indicator is red, press
(Standby-On) on the remote control.
To switch to standby
• Press (Standby-On) on the remote
control.
» The standby indicator switches to red.
•
•
•
Press
BACK A/CH on the remote
control to return to the previously
viewed channel.
Press CH +/- on the remote control or
P/CH +/- on the side of the TV.
Press OK to use the channel matrix.
Enter a channel number using the
Numeric buttons.
Note
• When you use a favourite list, you can only
select those channels in the list (see ‘Select a
favourite list’ on page 18).
To switch off
• Press POWER at the side of the TV.
» The standby indicator switches off.
Tip
• Though your TV consumes very little power
when in standby, energy continues to be
consumed. When not in use for an extended
period of time, disconnect the TV power cable
from the power outlet.
EN
7
Watch connected devices
Adjust TV volume
Note
• For easy access, add new devices to the home
menu before selecting them.
Use the source button
1
Press
SOURCE .
» The source list appears.
2
Press or
device.
3
Press OK to watch the connected device.
to select the connected
Use the home menu
Note
• You can add new devices to the home menu
for easy access .
1
Press (Home).
» The home menu appears.
2
3
Press
8
to select the device.
Press OK to watch the connected device
on your TV.
EN
To increase or decrease volume
• Press
+/-.
• Press VOLUME +/- on the side of the TV.
To mute or unmute sound
• Press to mute the sound.
• Press again to restore the sound.
Understand the information
banner
When you select a digital channel, an
information banner is displayed at the top of
the screen. The banner disappears after a few
seconds. The information banner provides
useful information on the current programme
on the screen such as channel name, program
title, start time of programme, and so on.
Install channels
The rst time you set up your TV, you are
prompted to select a menu language and to
install TV and digital radio channels (if available).
Check for TV channels or radio
stations
You can check for the availability of TV
channels or radio stations that have been
launched by the broadcaster after you have
installed the TV.
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1080p
1
000
2
3
CCTV-2 News
4
16:35
5
6
7
16:50
16:48
8
9
a Resolution: Indicates resolution type, for
example: 1080p.
b Favourite list indication: Indicated by a tick
if you have added this programme to your
favourite list setting.
c Channel number : In the format “###”.
d Channel name
e Programme name
1
2
Press DIGITAL MENU.
3
Press or to select [View TV
Channels] or [Listen to Radio Stations].
4
If new services are available, press to
enter into the list of services and press
or to move through the list.
5
Press the to return to the previous
menu or press DIGITAL MENU to exit.
Add new channels or stations to your
list
You can search for new TV channels or radio
stations that have been launched by the
broadcaster after the initial installation.
f Programme start time
g Programme time progress bar : Displays
time left indicator bar.
h Programme end time
i Clock : Current time
Select [Installation] > [Service List] and
press .
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
2
3
Press
.
Select [Installation] > [Service Setup]
and press .
Press to Add new services and press
OK to activate the installation.
EN
9
E n glish
5 Use your product
in digital mode
» A search begins. Any new channels are
added to the channel list menu. The
percentage of the installation that has
been completed and the number of
channels found is displayed.
Note
5
Install digital channels manually
You can manually install digital services by
keying the channel number.
• To cancel installation, press OK .
4
When the search is complete, press OK
to accept the new services.
5
Press to return to the previous menu
or press to exit.
Reinstall all channels
This option lets you reinstall all the digital TV
channels and radio stations.
Note
Press to return to the previous menu
or press DIGITAL MENU to exit.
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
2
Press DIGITAL MENU.
3
Press and
number and
4
5
Press OK to start the search.
Select [Installation] > [Service Setup] >
[Manual install services] and press .
to select the channel
to select [Start Scan].
Press to return to the previous menu
or press the blue button to exit.
• If you are not in the digital mode, press
ANALOG/DIGITAL .
Test digital reception
Caution
• Reinstalling services will overwrite all your
previously stored channels.
1
2
3
Press DIGITAL MENU.
Select [Installation] > [Service Setup] >
[Reinstall] services and press .
Press OK to start the installation.
» A search is for digital services is
started. The services are stored
automatically.
If using digital broadcasts, you can check the
quality and signal strength of digital channels.
This allows you to reposition and test your
antenna or satellite dish.
1
Press the numeric buttons (0-9) or CH
+/- to switch to the digital channel you
wish to test the signal of.
2
3
Press DIGITAL MENU
Note
• To cancel installation, press OK .
When the search is complete, the
menu indicates the number of digital
services found. You should see a list of
stored channels on the left panel.
4
Press OK to store the services.
10
EN
Select [Installation] > [Test Reception] >
[Frequency].
» The frequency of the current channel
is displayed.
4
Press to select [Network Name].
» The name of the broadcast network is
displayed.
5
Press to select [Signal Quality].
» An indicator bar displays the quality
level of the TV signal.
6
Press
to select [Signal Strength].
7
Press to return to the previous menu
or press DIGITAL MENU to exit.
Tip
• If the signal strength is poor, consider adjusting
or checking the connection of your antenna.
Contact a professional antenna installer for
best results.
Set your preferences
E n glish
» An indicator bar displays the strength
level of the TV signal.
Set your language
You can select your preferred language for
system menu and subtitle.
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
Change the order of stored
channels
You can change the order of the digital
channels and radio stations that you have
stored.
Note
1
Press DIGITAL MENU to display the onscreen menu and select [Preferences] >
[Language] and press .
2
Press or to select System or Subtitle
and press .
3
Press or to select the language and
press OK to conrm.
4
Press to return to the previous menu
or press the blue button to exit.
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
2
Menu options for language
Press DIGITAL MENU to display the onscreen menu and select [Installation] >
[Service List] > [Rearrange Services] and
press .
Press to select Uninstall services and
press or to select the services you
wish to uninstall.
3
Press OK to uninstall the service
temporarily.
4
Press to return to the previous menu
and to select [Move services].
5
Press or to highlight the service and
OK to select.
6
Press or to move the service to the
order you want and press OK to conrm.
7
Repeat the above steps to move other
services.
8
Press to return to the previous menu
or press DIGITAL MENU to exit.
System: To select the menu language.
Subtitle: To select your preferred subtitle
language.
Set your subtitle mode
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
Press DIGITAL MENU to display the onscreen menu and select [Preferences] >
[Subtitle Mode] and press .
2
3
Press
to select [On].
Press to return to the previous menu
or press DIGITAL MENU to exit.
EN
11
Set your digital audio output
• If Enable Pin Protection is Off, select On to
Note
proceed.
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
Note
Press DIGITAL MENU to display the onscreen menu and select [Preferences] >
[Digital Audio Output] and press .
2
Press or
output.
3
Press to return to the previous menu
or press DIGITAL MENU to exit.
2
Enter the default PIN code “1234” with
the numeric buttons (0-9).
You can access the menu now using the
default PIN code.
3
Press the or to highlight [On]
and press OK to turn on PIN code
protection.
to select [AC3] or [PCM]
Digital Audio Output
AC3: A compressed digital audio format
that supports 5.1 channel.
PCM: Pulse Code Modulation (PCM) is a
way of transmitting uncompressed digital
audio. PCM is used by Audio CDs.
Tip
• If your DVD or home theatre system supports
AC3 decoding, select AC3. Otherwise, select
PCM.
Control access to digital
channels
You can restrict access to the digital channels by
blocking them with an access PIN code.
Turn on PIN code protection
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
Press DIGITAL MENU to display the
on-screen menu and select [Access
Restrictions] and press .
12
EN
Change your PIN code
1
2
Turn on PIN code protection.
Press the to select Change PIN code
and press OK.
3
Enter your PIN code using the numeric
buttons (0-9) on the remote control.
4
Enter a new code when prompted to
enter your new PIN code.
5
6
Re-enter the new code when prompted
Press to return to the previous menu
or press DIGITAL MENU to exit.
Add all services to a favourite list
1
Press DIGITAL MENU to display the
on-screen menu and select [Favorites] >
list number (List 1 to List 4) > [Add all
services].
2
3
Press
4
Press to return to the previous menu
or press DIGITAL MENU to exit.
You can create a list of up to four of your
favourite TV channels and radio stations.
Note
• If you are not in the digital mode, press
ANALOG/DIGITAL .
1
2
Press DIGITAL MENU to display the onscreen menu and select [Favorites] > list
number (List 1 to List 4) and press OK.
Press the
options.
to enter the Favorites setting
to enter menu.
Select [Yes] and press OK to conrm
adding all the services.
Remove all services from a favourite
list
1
Press DIGITAL MENU to display the onscreen menu and select [Favorites] > list
number (List 1 to List 4) > [Remove all
services].
Press DIGITAL MENU to display the onscreen menu and select [Favorites] > list
number (List 1 to List 4) > [Name].
2
3
Press
2
Press or to move the cursor over the
character of the name list and press
or
to scroll through the character list.
4
Press to return to the previous menu
or press DIGITAL MENU to exit.
3
4
Press OK to conrm.
Change the name of a favourite list
1
to enter menu.
Select [Yes] and press OK to conrm
removing all the services.
Select [Yes] and press OK to conrm
changing the list name.
Select TV channels and radio stations
1
Press DIGITAL MENU to display the onscreen menu and select [Favorites] > list
number (List 1 to List 4)] > [Select TV
channels].
2
Press or to navigate the list of
channels or stations to select.
3
Press OK to select. An ‘X’ marks the
check box to indicate the channel or
station has been selected.
EN
13
E n glish
Set up your favourite
channels
Use the Electronic
Programme Guide
EPG is an on-screen guide available for digital
channels. EPG allows you to:
• View a list of digital programmes being
broadcast
• View upcoming programmes
• Group programmes by genre
• Set reminders when programmes start
• Set up preferred EPG channels
Switch on EPG
1
When watching TV, press GUIDE .
» The EPG planner screen appears
displaying information about the
scheduled programmes.
Tip
• Press
GUIDE to switch between EPG and
channel grid.
Use EPG
1
When watching TV, press GUIDE .
» The EPG planner screen appears.
2
Press or to change channels or
to [Now] or [Next].
3
Press
14
EN
or
GUIDE to exit the EPG menu.
•
3
4
Access TV menus
Menus help you to install channels, change
picture and sound settings and access other
features.
Press OK to conrm your choice.
Press
(Home) to exit.
Remove devices from the home menu
If a device is no longer connected to the TV,
remove it from the home menu.
1
Note
[Setup]Accesses menus to adjust
picture, sound and other TV settings.
[Add new device]Adds new devices
to the home menu for easy access.
Press (Home).
» The home menu appears.
• If you are not in the analogue mode, press
ANALOG/DIGITAL .
Access the home menu
The home menu gives you easy access to
connected devices, picture and sound settings
as well as other useful features.
1
Press (Home).
» The home menu appears.
W t TV
Watch
Watc
2
Add new device
W t TV
Watch
Watc
Add new device
Setup
2
Press OPTIONS .
» The [Remove] menu appears.
3
4
Press
to select an icon.
Press OK to remove the icon.
» The selected icon is removed from the
home menu.
Setup
Press
to select an option.
• [Watch TV]Switches to TV mode.
EN
15
E n glish
•
6 Use your product
in analogue mode
Change picture and sound
settings
Change picture and sound settings to suit your
preferences. You can apply pre-dened settings
or change settings manually.
Use settings assistant
Use the settings assistant to guide you through
the best picture settings.
1
Press (Home).
» The home menu appears.
2
Press
to select [Setup] > [Picture]
> [Settings assistant] > [Start].
3
Press OK .
» The [Settings assistant] menu appears.
Follow the on-screen instructions to
choose your preferred picture settings.
Use smart picture
Use smart picture to apply pre-dened
picture settings.
1
Press PICTURE.
» The [Smart picture] menu appears.
2
Press
to select from the following
smart picture settings:
• [Personal]Lists customised personal
picture settings.
• [Vivid]Maximises picture settings.
• [Standard]Adjusts picture settings
to suit most environments and types
of video.
• [Movie]Applies picture settings
ideally suited for movie viewing.
• [Game]Applies picture settings
maximised for fast-moving games.
• [Energy saving]Applies low-energy
picture settings.
16
EN
Manually adjust picture settings
1
2
3
Press
(Home).
Press
to select [Setup] >
[Picture].
» The [Picture] menu appears.
Press
to select from the following
settings and adjust:
• [Smart picture]Accesses pre-dened
smart picture settings.
• [Contrast]Adjusts the intensity of
bright areas, keeping dark areas
unchanged.
• [Brightness]Adjusts the intensity and
details of dark areas.
• [Colour]Adjusts colour saturation.
• [Hue]Compensates colour variations
in NTSC encoded transmissions.
• [Sharpness]Adjusts the level of
sharpness in image details.
• [Noise reduction]Filters and reduces
noise in an image.
• [Colour temperature]Introduces
more orange tones ([Warm]) or
blue tones ([Cool]) to the picture.
• [Pixel Plus HD]Fine-tunes each pixel
to match surrounding pixels. This
produces a brilliant, high-denition
image.
• [HD Natural Motion]Reduces eld
and line icker to display movement
smoothly. You can switch HDNM on
or off.
• [100Hz LCD]Not available in all
models. Sets the TV refresh rate to
a maximum of 100Hz to provide
superior motion sharpness, better
black level, high contrast with a
icker-free, quiet image and a larger
viewing angle.
• [Advance sharpness]Not available
in all models. Enables superior
sharpness, especially on lines and
contours in the picture.
• [Dynamic contrast]Automatically
enhances contrast in an image.
•
•
•
•
•
•
•
[Dynamic backlight]Adjusts the
brightness of the TV backlight to
match lighting conditions.
[MPEG artifact reduction] Not
available in all models. Smoothes out
transitions on digital pictures. You
can switch this feature on or off.
[Colour enhancement]Makes
colours more vivid and improves the
resolution of details in bright colours.
You can switch this feature on or off.
[PC mode]Adjusts picture settings
when a PC is connected to the TV.
[Light sensor]Dynamically adjusts
picture settings to match lighting
conditions.
[Picture format]Changes the picture
format.
[Horizontal shift]Adjusts the picture
horizontally for PC-VGA or HD
input.
[Vertical shift]Adjusts the picture
vertically for PC-VGA or HD input.
Change picture format
Summary of picture formats
The following picture settings can be
congured.
E n glish
•
Note
• Depending on the format of the picture
source, some picture settings are not available.
[Super zoom](Not for HD
and PC mode.) Removes
the black bars on the side
of 4:3 broadcasts. There is
minimal distortion.
[4:3]Shows the classic 4:3
format.
[Subtitle zoom] (Not
for HD and PC mode.)
Displays 4:3 pictures over
the full area of the screen,
with sub-titles visible. Part
of the top of the picture is
clipped off.
[Movie expand 14:9](Not
for HD and PC mode.)
Scales 4:3 format to 14:9.
1
Press
FORMAT.
» A picture format bar appears.
[Movie expand 16:9](Not
for HD and PC mode.)
Scales 4:3 format to 16:9.
2
Press
to select a picture format.
» The selected picture format is
previewed.
[Wide screen]Stretches
the classic 4:3 format to
16:9.
[Unscaled]For HD and PC
mode only, and in selected
models only. Allows
maximum sharpness.
Some distortion may
be present due to the
broadcaster’s systems.
Set your PC resolution to
wide screen mode for best
results.
EN
17
Use smart sound
•
Use smart sound to apply pre-dened sound
settings.
•
•
1
Press SOUND.
» The [Smart sound] menu appears.
2
Press
to select a smart sound setting:
• [Standard]Adjusts sound settings to
suit most environments and types of
audio.
• [News]Applies sound settings ideally
suited for spoken audio, such as the
news.
• [Movie]Applies sound settings ideally
suited for movies.
• [Personal]Applies the settings that
were customised in the sound menu.
[Headphone volume]Adjusts
headphone volume.
[Auto volume]Automatically
reduces sudden volume changes, for
example, when switching channels.
When enabled, this produces a more
consistent audio volume.
[Delta volume]Corrects volume
differences between TV channels
and connected devices (switch
to your connected device when
adjusting [Delta volume]).
Create and use lists of
favourite channels
You can create lists of your preferred TV
channels and radio stations so that you can nd
those channels easily.
Tip
• You can create and store up to four favourite
lists on your TV.
Adjust sound settings
1
2
3
18
Press
(Home).
Select a favourite list
Press
to select [Setup] > [Sound].
» The [Sound] menu appears.
Press
to select and adjust:
• [Smart sound]Accesses pre-dened
smart sound settings.
• [Bass]Adjusts the bass level.
• [Treble]Adjusts the treble level.
• [Volume]Adjusts the volume.
• [Balance]Adjusts the balance of the
right and left speakers to best suit
your listening position.
• [Dual I-II]Selects between audio
languages if dual sound is broadcast.
• [TV speakers]Sets the TV speakers
on or off, or outputs sound to
an EasyLink-compliant device.
[EasyLink] must be activated in the
[Preferences] menu to make the
[TV speakers] menu available.
• [Surround]Enables spatial sound.
EN
1
When watching TV, press OK .
» The channel grid appears.
2
Press OK .
» The options menu appears.
3
Press
to select [Show favourite
channels].
» The favourite lists appear.
4
5
Press
to select a favourite list or [All].
Press OK .
» If you selected a favourite list, only
channels in the list appear in the
channel grid; if you selected [All],
all installed channels appear in the
channel grid.
6
Press
to exit the options menu.
Tip
• View all channels before adding a channel to a
Use timers
E n glish
Add a channel to a favourite list
You can set timers to switch the TV on or
switch to standby at a specied time.
favourite list.
1
2
3
4
5
6
7
When watching TV, switch to the channel
you want to add to a favourite list (see
‘Switch channels’ on page 7 ).
Press .
» The channel options menu appears.
Press
to select [Mark as favourite].
Press OK .
Set the time
1
2
3
4
5
6
Press
(Home).
Select [Setup] > [Features] > [Clock].
Press OK .
Press
to set the time.
Select [Done].
Press OK .
Select a favourite list to add the channel to.
Press OK .
» The channel is added to the favourite
list.
Press
BACK A/CH to exit the channel
options menu.
» The channel grid appears.
Automatically switch the TV to
standby (sleeptimer)
Sleeptimer switches the TV to standby after a
pre-dened period of time.
Tip
• You can always switch off your TV earlier or
Remove a channel from a favourite
list
Note
• Select the favourite list to edit, before
reset the sleeptimer during the countdown.
1
Press (Home).
» The home menu appears.
2
Press
to select [Setup] >
[Features] > [Sleep timer].
» The [Sleep timer] menu appears.
3
Press
to set the sleep time.
» The sleeptimer can be up to 180
minutes in steps of ve minutes. If
set to zero minutes, the sleeptimer is
switched off.
4
Press OK .
» The TV switches to standby after the
pre-dened period of time.
removing a channel.
1
When watching TV, press OK .
» The channel grid appears.
2
3
Press
4
5
6
to select a channel.
Press OPTIONS .
» The channel options menu appears.
Press
to select [Unmark as favourite].
Press OK .
» The channel is removed from the
favourite list.
Press
BACK A/CH to exit the channel
options menu.
» The updated channel grid appears,
displaying the current channels in the
favourite list.
EN
19
Automatically switch the TV on (on
timer)
You can switch the TV to a specied channel
at a specied time, from standby.
1
2
3
4
Press
(Home).
Lock or unlock the TV
Locking the TV prevents your child from
accessing all channels and connected devices.
1
2
Select [Setup] > [Features] > [On timer]
> [Activate].
Press OK .
Press
to set the frequency, time
and channel.
Tip
• To switch off [On timer], select [OFF] in the
[On timer] menu.
Press
(Home).
Press
to select [Setup] >
[Features] > [TV lock].
» A message appears prompting you to
enter your PIN code.
3
Enter your PIN code with the Numeric
buttons.
» The [TV lock] menu appears.
4
5
Press
to select [Lock] or [Unlock].
Press OK .
» All channels and connected devices are
locked or unlocked.
Set or change your PIN code
1
2
3
4
Press
(Home).
Press
to select [Setup] >
[Features] > [Change code].
» The [Change code] menu appears.
Enter a four-digit PIN using the Numeric
buttons.
• If you have a PIN, enter your current
PIN.
• If you do not have a PIN or if you
have forgotten your PIN, enter
‘0711’.
Enter your PIN again to conrm.
Use child control
You can prevent your children from watching
certain programmes or certain channels by
locking the TV controls.
20
EN
Lock or unlock one or more channels
1
When watching TV, press OK .
» The channel grid appears. The active
channel is highlighted.
2
3
4
Press
Press
OPTIONS .
to select [Lock/Unlock chan.].
Key in your PIN code.
» The channel displays the lock icon.
Use subtitles
You can enable subtitles for each TV channel.
With digital broadcasts, you have the additional
option of selecting a preferred subtitle language.
Enable subtitles on digital TV channels
1
When watching digital channels, press
SUBTITLE .
» The [Subtitle mode] menu appears.
2
Select [On] to display subtitles or [On
during mute] to display subtitles only
when audio is muted.
3
Press OK to enable subtitles.
Note
View photos, play music and
watch video from a USB
storage device
• When you select a subtitle language on
a digital TV channel as described below,
the preferred subtitle language set in the
installation menu is temporarily overruled.
1
2
3
4
5
Press
Caution
• Philips is not responsible if the USB storage
device is not supported nor is it responsible
for damage or loss of data from the device.
(Home).
Press
to select [Setup] >
[Features] > [Subtitle language].
Press OK or to enter the list of
available languages.
Press
E n glish
Select a subtitle language on digital TV
channels
to select a subtitle language.
Press OK to enable your selection.
Your TV is tted with a USB connector that
enables you to view photos, listen to music or
watch movies stored on a USB storage device.
Supported le formats
Pictures
JPEG (non-progressive only)
Music
MP3
Video
H.264, MPEG4
Tip
Note
• You can also access [Subtitle language] menu
while watching TV by pressing
[Subtitle language].
OPTIONS >
Use the TV clock
You can display a clock on the TV screen. The
clock displays the current time using time data
received from your TV service operator.
Display the TV clock
1
When watching TV, press OPTIONS .
» The TV options menu appears.
2
3
Select [Clock].
Press OK .
» The clock is displayed.
• Only FAT or DOS-formatted USB storage
devices are supported. File names must not
exceed 128 characters.
• Your TV only supports USB ash drives in
FAT/FAT32 format. It does not support other
devices that can be connected to the USB
port including but not limited to the following:
portable storage devices such as external
hard drives and mini hard drives, MP3 player,
digital camera, phone, portable video player,
portable multimedia player.
• The capacity of the USB storage device must
not exceed 32 gigabytes.
• The le size of all supported formats must not
exceed 4 gigabytes.
Connect a USB storage device and
enter the content browser
1
2
Note
• The clock is disabled automatically after ten
minutes. To disable the clock before that,
repeat this procedure.
Turn on the TV.
Connect the USB device to the USB port
on the side of the TV.
3
Press (Home).
» The home menu appears.
4
Press
to select [Browse USB].
EN
21
5
Press OK to conrm.
» The USB content browser appears.
2
Note
• If you connect multiple USB storage devices
via USB hub, a message appears prompting
you to select a device. Press
to select the
device, then press OK to conrm.
Press:
•
to pause the slide show.
•
or
to go back or move
forward to the next image.
•
BACK A/CH or to stop the
slide show and return to the USB
content browser.
Change slide show settings
Tip
1
When viewing a slide show, press
OPTIONS .
» The slide show options menu appears.
2
Press
to select from the following
settings and adjust:
• [Start/Stop slide.]Starts or stops a
slide show.
• [Slideshow transitions]Displays a list
of transition styles.
• [Slideshow frequency]Sets the
amount of time that a picture is
shown.
• [Rotate image]Rotates a picture.
• [Show info]Displays the picture
name, date, size and next picture in
the slide show.
3
Press OK to conrm the setting change.
• Press
BROWSE to switch between
thumbnail and le browsing views.
Disconnect a USB storage device
Caution
• Follow this procedure to avoid damage to your
USB storage device.
1
Press
menu.
2
Wait for ve seconds before
disconnecting the USB storage device.
BACK A/CH to exit the [USB]
View photos
1
In the USB content browser, press
enter the [Picture] folder.
2
3
Press
to
to select a photo.
Press OK to view a full screen image of
the photo.
Listen to music
1
Connect a USB storage device to the
USB port on the side of the TV.
2
3
Press
Tip
• When in full screen mode, press
to move
4
between photos.
5
View a slide show of your photos
1
When a full screen image of a photo is
displayed, press
or OK .
» A slide show begins from the selected
image.
22
EN
to enter the menu.
Select [Music], and then press
the [Music] folder.
Press or
album.
to enter
to select a song or a music
Press OK to play the selected song or
album.
Music settings
• [Show info]Displays the le name.
• [Repeat]Repeats a song or an album.
• [Shufe]Plays songs randomly.
1
2
3
In the USB content browser, press
enter the [VIDEO] folder.
Press
to select a video.
to
Press OK to play the video.
Upload a wallpaper picture from a
USB device
Before performing this procedure, be sure to
have available a USB storage device containing
the picture you intend to use as wallpaper.
1
Connect the USB storage device to the
TV.
» The home menu appears with
[Browse USB] already highlighted.
2
3
4
Press OK.
Use Scenea to display a
picture as TV wallpaper
You can use the Scenea feature to display a still
picture as wallpaper on your TV. This feature is
for home mode only.
Press
to select a picture.
Press SCENEA to set the picture as
personalised wallpaper.
Activate Scenea
Update the TV software
Single-picture wallpaper
Press SCENEA on your remote control.
» The default or pre-loaded picture is
displayed.
Note
• To deactivate the wallpaper, press any remote
control button except , SOUND, and
PICTURE .
• The wallpaper is also deactivated when you
connect a USB storage device to the TV or
start an EasyLink-compliant device through
one-touch play.
Wallpaper slide show
Make sure the wallpaper is not yet activated.
1 Connect a USB storage device to the TV.
2 Press SCENEA .
» All pictures in the USB storage device
are displayed.
Note
• The wallpaper display duration is determined
Philips continuously tries to improve its
products and we recommend that you update
the TV software when updates are available.
Check www.philips.com/support for availability.
Update software (analogue
broadcasts)
Before performing this procedure be sure to:
• Set aside some time to complete the
entire update.
• Have available a USB storage device with
at least 64MB of storage space.
• Have access to a computer with a USB
port and internet access.
Step 1 Download the TV identication le
1
2
3
Press
(Home)
Select [Setup] > [Software update] >
[Update assistant] > [Action].
Select [Start].
by the pre-dened sleeptimer settings (see
‘Automatically switch the TV to standby
(sleeptimer)’ on page 19). When sleeptimer is
off, the wallpaper is displayed for a maximum
of 120 minutes.
EN
23
E n glish
Watch video from a USB device
4
Follow the on-screen instructions to
download the TV identication le to the
USB storage device.
Note
• The TV restarts after the software update is
complete.
Step 2 Download the latest software
1
2
3
4
Connect the USB storage device to a
computer with internet connection.
Locate and open the le update.htm on
your USB storage device.
Read the on-screen instructions and click
the Send ID button.
If a new software is available, the update
is downloaded to the USB storage device.
Change TV preferences
The [Preferences] menu allows you to
customise various features and functions.
1
2
Disconnect the USB storage device.
Step 3 Update the TV software
Caution
• Do not disconnect the USB storage device
from the TV during the software update.
• If a power failure occurs during the update, do
not remove the USB storage device from the
TV. The TV will continue the update as soon
as power comes back.
1
Connect the USB storage device to the
TV.
» An on-screen message prompts you to
update your TV software.
2
3
4
Select [Update].
Select [Start].
Follow the on-screen instructions to
update the TV software.
Update using a USB device
Connect your USB device to the USB port at
the side of your TV.
1 If the software update screen does not
appear automatically, select [Setup] >
[Software update] > [Local updates]
> [USB] to update the TV software
manually.
2 Follow the on-screen instructions to
complete the update.
24
EN
Press
(Home).
Select [Setup] > [Installation] >
[Preferences].
• [Location]Optimises TV settings for
your location - home or shop.
• [Volume bar]Displays the volume
bar when adjusting the volume.
• [Channel info.]Displays information
about the TV channel every time you
switch channels.
• [EasyLink]Enables one-touch play
and one-touch standby between
EasyLink-compliant devices.
• [Pixel Plus Link]Overrides the
settings of connected devices and
uses the settings of the TV.
• [E-sticker]For shop mode only. Sets
the location of the e-sticker.
Start a TV demo
You can use demonstrations to better
understand the features of your TV. Some
demos are not available on certain models.
When a demo is available, it is displayed in the
menu list.
1
2
3
Press DEMO.
Press
or
to select a demo.
Press OK to start the demo.
Follow on-screen instructions to view the
demo.
5
Press DEMO to exit.
E n glish
4
Reset the TV to factory
settings
You can restore the default picture and sound
settings of your TV. Channel installation settings
remain the same.
1
2
Press
(Home).
Select [Setup] > [Installation] > [Factory
settings].
3
Press to enter the [Factory settings]
menu.
» [Reset] is highlighted.
4
5
Press OK to reset to default settings.
Press
(Home) to exit.
EN
25
7 Connect devices
This section describes how to connect
various devices with different connectors and
supplements examples provided in the Quick
Start.
b AUDIO IN L/R
Audio input from devices that require
a separate audio connection, such as a
computer.
c VGA
Video input from a computer.
Note
• Different types of connectors may be used to
connect a device to your TV, depending on
availability and your needs.
d SPDIF OUT
Digital audio output to home theatres
and other digital audio systems.
e CVI ( Y Pb Pr and AUDIO L/R)
Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.
Back connectors
f AV OUT ( VIDEO and AUDIO L/R)
Only in analogue mode. Audio and
video output to analogue devices such as
another TV or a recording device.
1
g AV IN ( VIDEO and AUDIO L/R)
Analogue audio and video input from
analogue or digital devices such as DVD
players, satellite receivers and VCRs.
2
h HDMI 1/2
Digital audio and video input from highdenition digital devices such as Blu-ray
players.
3
4
5
26
a TV ANTENNA
Signal input from an antenna, cable or
satellite.
EN
6
7
8
1
2
3
4
Connect a computer
E n glish
Side connectors
Before you connect a computer to the TV
• Set the monitor refresh rate on your
computer to 60Hz.
• Press
FORMAT and change the TV
picture format to [Unscaled].
Connect a computer with one of the
following connectors:
Note
• Connections via DVI or VGA require an
additional audio cable.
5
•
HDMI cable
•
DVI-HDMI cable
6
7
a AUDIO IN L/R
Audio input from analogue devices
connected to VIDEO or S-VIDEO.
b VIDEO
Composite video input from analogue
devices such as VCRs.
c S-VIDEO
Video input from analogue devices such
as satellite receivers. When you use this
connector, do not use connector for
video signals.
d
AUDIO IN:
LEFT / RIGHT
HDMI 1 / DVI
HDMI 2 / DVI
HDMI 3 / DVI
VGA
DVI
Stereo audio output to headphones or
earphones.
e USB
Data input from USB storage devices.
f HDMI
Digital audio and video input from highdenition digital devices such as Blu-ray
players.
g SERV. U
For use by service personnel only.
EN
27
HDMI cable and HDMI-DVI adaptor
•
AUDIO IN:
LEFT / RIGHT
HDMI 1 / DVI
HDMI 2 / DVI
HDMI 3 / DVI
VGA
6
Switch on your device and check for
video and audio output.
7
If there is video and audio output, press
OK .
Repeat the procedure until all devices are
correctly assigned to connectors.
Use Philips EasyLink
DVI
VGA cable
•
AUDIO IN:
LEFT / RIGHT
HDMI 1 / DVI
HDMI 2 / DVI
HDMI 3 / DVI
VGA
Your TV supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
Note
• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
Note
VGA
VGA
• The EasyLink-compliant device must be
switched on and selected as the source.
EasyLink features
Assign devices
After connecting devices, assign the device
attached to each connector. This allows you to
easily identify devices connected to your TV.
1
2
3
Press
4
Press or to select the connector
your device is connected to and press .
5
If available, press or to select the
audio connector your device is connected
to and press .
28
EN
(Home).
Press OK or .
Press
.
or
to select a device and press
One-touch play
When you connect your TV to devices that
support one-touch play, you can control your
TV and the devices with one remote control.
For example, when you press Play on your
DVD remote control, your TV automatically
switches to the correct channel to show the
DVD content.
One-touch standby
When you connect your TV to devices that
support standby, you can use your TV remote
control to put your TV and all connected
HDMI devices in standby mode.
System audio control
When you connect your TV to HDMI
CEC compliant devices, your TV can
switch automatically to play audio from the
connected device.
EasyLink buttons
Tip
• Press TV to switch back to the aerial source
from EasyLink mode.
Enable or disable EasyLink
Note
• Do not enable Philips EasyLink if you do not
intend to use it.
You can control EasyLink-compliant devices
with the following buttons on the remote
control of your TV.
1
2
Press
Button
(Play/
Pause)
3
Select [ON] or [OFF].
EasyLink function
Starts, pauses or resumes
playback on your EasyLink
device.
(Stop)
Stops playback on your EasyLink
device.
(Record) Starts or stops video recording
on your EasyLink device.
(Fast
Searches backward.
Reverse)
(Fast
Searches forward.
Forward)
0-9
When EasyLink is enabled,
(Numeric selects a title, chapter or track.
buttons)
Navigates through the menus of
the EasyLink-compliant device.
OK
Activates a selection or accesses
the menu of the EasyLinkcompliant device.
Displays the menus of the
OPTIONS EasyLink-compliant device. Note
that when (Home) is pressed,
the TV menu is displayed.
(Standby- When EasyLink is enabled,
On)
switches the TV and all EasyLink
devices to standby. Note that
you must press and hold
(Standby-On) for at least 3
seconds for this to occur.
E n glish
To use one-touch audio, you must map the
audio input from the connected device to
your TV.
You can use the remote control from the
connected device to adjust the volume.
Remote control (RC) key forwarding
RC key forwarding allows you to control
EasyLink-compliant devices using your TV
remote control.
(Home).
Select [Installation] > [Preferences] >
[EasyLink].
Enable or disable remote control key
forwarding
1
2
3
4
5
6
7
Press
(Home).
Select a device that is connected to an
HDMI connector.
Press
OPTIONS .
Select [En./Dis. RC pass.].
Press OK .
Press or
connector.
to highlight an HDMI
Press OK to enable RC key forwarding
for the selected HDMI connector.
Set TV speakers to EasyLink mode
When enabled, this feature automatically
turns off TV speakers when content from an
EasyLink-compliant home theatre system is
played. Audio is played only from the home
theatre system’s speakers.
1
2
3
Press
(Home).
Press
to select [Setup] > [Sound].
» The [Sound] menu appears.
Select [TV speakers].
» The [TV speakers] menu appears.
EN
29
4
Select [Auto (EasyLink)].
» TV speakers are set to EasyLink mode.
Use a Kensington lock
There is a Kensington security slot at the back
of the TV. Prevent theft by looping a Kensington
lock between the slot and a permanent object,
such as a heavy table.
30
EN
Product information is subject to change
without notice. For detailed product
information, go to www.philips.com/support.
Tuner/Reception/Transmission
•
•
E n glish
8 Product
information
Aerial input: 75ohm coaxial (IEC75)
TV system: PAL BG, SECAM BG, PAL I,
PAL DK, SECAM DK, NTSC M
Video playback: NTSC, PAL, SECAM
•
Multimedia
Supported display resolutions
•
•
Computer formats
HDMI:
Resolution
Refresh rate (Hz)
640 x 480
720 x 400
800 x 600
1024 x 768
1280 x 1024
1360 x 768
1600 x 1200
1920 x 1080
60, 72, 75
70
60, 72, 75
60, 70, 75
60
60
60
50, 60
VGA:
Resolution
Refresh rate (Hz)
640 x 480
720 x 400
800 x 600
1024 x 768
1280 x 768
1280 x 1024
1360 x 768
60, 72, 75, 85
70, 85
60, 72, 75, 85
60, 70, 75, 85
60
60
60
Connection: USB
Playback formats: H.264, MPEG4, JPEG, MP3
Container
Video
Codec
Audio
Codec
File
extension
AVI
MPEG 4 SP,
MPEG 4 ASP,
MP4S,MP4V
MPEG
Layer 2/3,
AC3
.avi
mpeg
MPEG-1
MPEG 1
Layer 2
.mpg,
.mpe,
.mpeg,
.vob,
.dat
mpeg4
MPEG-4 AVC
(h.264, L2-CIF),
MPEG-4 AVC
(h.264, L4-HD)
AAC-LC
.m4v,
.mp4,
.mov
Remote control
•
Batteries: 2 x AAA (LR03 type)
Connections
Video formats
Resolution
Refresh rate (Hz)
640 x 480p
720 (1440) x 480i
720 (1440) x 576i
720 x 480p
720 x 576p
1280 x 720p
1920 x 1080i
1920 x 1080p
60
60
50
60
50
50, 60
50, 60
24, 25, 30, 50, 60
•
•
•
•
•
•
•
•
•
•
•
•
Headphone out (stereo mini-jack)
TV aerial
S-Video
CVBS in
CVBS out
YPbPr: Component video (CVI in)
VGA in
HDMI
VGA Audio in
SPDIF out
USB
Service connector
EN
31
Power
•
•
•
32
Mains power: AC 220-240V, 50-60Hz
(+/- 10%)
Standby power: < 0.15W
Ambient temperature: 5 to 35 degrees
Celsius
EN
This section describes commonly encountered
issues and accompanying solutions.
General TV issues
The TV does not switch on:
•
Disconnect the power cable from the
power outlet. Wait for one minute then
reconnect it.
•
Check that the power cable is securely
connected.
The remote control is not working properly:
•
Check that the remote control batteries
are correctly inserted according to the
+/- orientation.
•
Replace the remote control batteries if
they are at or weak.
•
Clean the remote control and TV sensor
lens.
The standby light on the TV blinks red:
•
Disconnect the power cable from the
power outlet. Wait until the TV cools
down before reconnecting the power
cable. If the blinking reoccurs, contact
Philips Consumer Care.
You forgot the code to unlock the child lock
feature
•
Enter ‘0711’. This code is only for the
analogue mode.
The TV menu is in the wrong language
•
Change the TV menu to your preferred
language.
When turning the TV on/off/to standby, you
hear a creaking sound from the TV chassis:
No action is required. The creaking sound
•
is normal expansion and contraction of
the TV as it cools and warms up. This
does not impact performance.
TV channel issues
Previously installed channels do not appear in
the channel list:
•
Check that the correct channel list is
selected.
No digital channels were found during the
installation:
•
Ensure that you have a digital TV
subscription. Contact your digital TV
service provider.
Picture issues
The TV is on, but there is no picture:
•
Check that the antenna is properly
connected to the TV.
•
Check that the correct device is selected
as the TV source.
There is sound but no picture:
•
Check that the picture settings are
correctly set.
There is poor TV reception from an antenna
connection:
•
Check that the antenna is properly
connected to the TV.
•
Loudspeakers, unearthed audio devices,
neon lights, high buildings and other large
objects can inuence reception quality.
If possible, try to improve the reception
quality by changing the antenna direction
or moving devices away from the TV.
•
If reception on only one channel is poor,
ne tune this channel.
There is poor picture quality from connected
devices:
•
Check that the devices are connected
properly.
•
Check that the picture settings are
correctly set.
The TV did not save your picture settings:
• Check that the TV location is set to the
home setting. This mode offers you the
exibility to change and save settings.
EN
33
E n glish
9 Troubleshooting
The picture does not t the screen; it is too
big or too small:
Try using a different picture format.
•
The picture position is incorrect:
Picture signals from some devices may
•
not t the screen correctly. Check the
signal output of the device.
Sound issues
There is a picture but no sound from the TV:
Note
• If no audio signal is detected, the TV
automatically switches the audio output off
— this does not indicate malfunction.
Check that all cables are properly
connected.
Check that the volume is not set to 0.
•
Check that the sound is not muted.
•
There is a picture but the sound quality is poor:
Check that the sound settings are
•
correctly set.
There is a picture but sound comes from one
speaker only:
Verify that sound balance is set to the centre.
•
•
HDMI connection issues
There are problems with HDMI devices:
Note that HDCP support can delay the
•
time taken for a TV to display content
from a HDMI device.
If the TV does not recognise the HDMI
•
device and no picture is displayed, try
switching the source from one device to
another and back again.
If there are intermittent sound
•
disruptions, check that output settings
from the HDMI device are correct.
•
If a HDMI-to-DVI adaptor or HDMI to
DVI cable is used, check that an additional
audio cable is connected to AUDIO L/R
or AUDIO IN (mini-jack only).
34
EN
USB connection issues
USB device content is not displayed:
Check that the USB storage device is
•
set to ‘Mass Storage Class’ compliant,
as described in the storage device’s
documentation.
Check that the USB storage device is
•
compatible with the TV.
Check that the audio and picture le
•
formats are supported by the TV.
Audio and picture les do not play or display
smoothly
The transfer performance of the USB
•
storage device may limit the data transfer
rate to the TV, causing poor playback.
Computer connection issues
The computer display on the TV is not stable:
•
Check that a supported resolution and
refresh rate is selected on the computer.
•
Set the TV picture format to unscaled.
Contact us
If you cannot resolve your problem, refer to
the FAQs for this TV at www.philips.com/
support.
If the problem remains unresolved, contact
Philips Consumer Care in your country as
listed in this user manual.
Warning
• Do not attempt to repair the TV yourself. This
may cause severe injury, irreparable damage to
your TV or void your warranty.
Note
• Make a note of your TV model and serial
number before you contact Philips. These
numbers are printed on the back of the TV
and on the packaging.
E
B
Batteries
4, 32
C
Channel list
favourite
troubleshooting
update
Channels
favourite list
install
automatic
manual
rearrange
rename
test reception
Child lock
TV lock
Clock
Computer format
technical specications
Connections
HDMI
troubleshooting
mains cord
technical specications
troubleshooting
USB
troubleshooting
Connectors
assign devices
18
33
19
18
31
31
32
31
10
20
21
31
34
26
31
34
34
28
D
Demo
Devices
assign
watch
Digital channel
test reception
Digital radio
Display
resolution
23
E n glish
screen saver
10 Index
24
28
8
10
14
EasyLink
disable
enable
Environmental care
29
29
4
F
Factory settings
Favourite list
select
set up
25
18
18
H
HDMI cable
troubleshooting
Home mode
34
24
I
Installation
automatic
manual
31
31
L
Language
troubleshooting
Location
Lock
TV
33
24
20
M
Menu
child lock
language
main menu
troubleshooting
Multimedia
technical specications
Music
digital radio
USB
20
33
15
33
31
14
22
31
EN
35
P
Picture format
troubleshooting
Picture settings
PIN code
Power
33
16
33
33
R
Reception
Remote control
technical specications
troubleshooting
33
31
33
S
Screen saver
Settings assistant
Sleep timer
Smart settings
Sound settings
Standby
troubleshooting
Subtitles
language
on analogue channel
on digital channel
23
16
19
16 , 18
18
33
21
20
20
T
Technical specications
Timer
on timer
sleeptimer
standby
Transmission
troubleshooting
Troubleshooting
TV
adjust volume
menu
software
standby
switch channels
switch off
switch on
troubleshooting
tuner technical specications
36
EN
31
20
19
19
33
33
8
15
23
7
7
7
7
33
31
TV lock
lock channels
lock connected devices
PIN code
20
20
33
U
USB
listen to music
upload a picture from
view photos
22
23
22
V
Video format
video format technical specications
Volume
adjust
31
8
W
Wallpaper
23
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: 3139 125 41061