Audison measurement standards
(Power measures taken according to audison standard, 1998 edition)
- 12VDC and 13.8VDC;
- 1 kHz or crossover cut-off frequency;
- 0.3% THD @ nominal power; 1% THD @ continuous power;
- Tolerance: +10%; -5%;
- Continous power given by RMS Voltage measured on resistive load;
- The nominal power of the amplifier is measured upon a battery voltage of 12 Volts with
a 4 Ohm load and with all channels in function.
OWNER’S MANUAL
PRINTED IN ITALY - Code 10125770
CAR POWER AMPLIFIER
is a division of
62018 Potenza Picena (MC) Italy
Tel. 0733.870870 • Fax 0733.870880 • http://www.audison.com • e-mail: com@audison.com
INTRODUCTION
INTRODUCTION
Audison thanks you for preferring this product and compliments you on your choice since it was
designed in order to insure outstanding musical and instrumental performances.
Before use instructions, please carefully read the safety norms you have to respect in order to avoid
unpleasant inconveniences and to enjoy this product at best.
PRECAUTIONS
- Avoid to install the amplifier where temperature is below 0°C or above 55°C and in non ventilated
places.
- The amplifier needs 12VDC power supply voltage with negative to ground. Be sure that your car electric
system is compatible with the amplifier ordinary functioning.
- For safer driving, we recommend to adjust volume not to drown external traffic sounds.
WARNING!:
While installing the amplifier, make sure that the cable coming from the battery positive pole (+)
doesn’t touch the amplifier heat sink.
The heat sink is directly connected to the battery negative pole (-) through the screws which fix it to the
vehicle chassis. Its contact with the positive pole cable would cause short circuit and, thus, possible fires
and battery damages.
Please connect power supply cables to the amplifier terminal blocks (POWER + and -) before and
to battery AFTER, to get maximum safety.
CAUTIONS
INPUTS: If the source output signal ground (PRE OUT) is not connected to the source chassis and the
system sound is not powerful enough or is distorted, try to solve the problem by connecting the output
signal cable braided shield (PRE OUT) to a point of the source chassis.
OUTPUTS: Don’t connect –L and –R power outputs to each other or to ground (car chassis). In case you
use an external crossover, make sure that channels grounds are not connected one to the other.
2
INSTALLATION
CONTENTS
audison cable PRODUCTS FOR ELECTRIC CONNECTIONS
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p.
4
In-Out panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
Power supply panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
Controls panel
Functions and controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Setting panel
Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Amplifier configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Subsonic filter cut-off frequency modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCA-VCA1D modules insertion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
11
11
Technical features
Size for fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
LRx 4.300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Accessories
VCR01K, VCRAK and VCRDK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
CLK2 - LRx Cooling Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Configurations
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Configurations table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Controls panel diagram and configuration switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Configuration examples
Front+Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Front+Rear+Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Front+Rear+Sub . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Installation
Logo rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Amplifier fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
audison cable products for electric connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20
21
21
22
audison measurement standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
22
3
DESCRIPTION
Audison LRx 4.300:
Four channel car power amplifier characterised by excellent musical performances, small size and
outstanding energy reserve.
Its PWM power supply stage is made with two pairs of 70A MOSFETs; it is stabilised and oversize.
Input stage is provided with a special circuit (LNS) which permits the system disturbances rejection,
reducing noise that is usually due to the vehicle electric parts (alternator, electronic injection, etc.),
without altering musical signal quality.
Driver stages are characterised by a very linear circuitry. They have coupled differential transistors and an
A Class complementary voltage amplifier. Power sections have Darlington configuration with high gain
and SOA (Safety Operation Area) BJT TO247. Thanks to its great capacity to supply current, this amplifier
can easily drive even the hardest loads and satisfy whatever power needs. It can give 65W per channel
on 4 Ohm load and 105W per channel at 2 Ohms in continuous mode. Power increases up to 210Wx2 at
4 Ohms in mono (bridged); it is 65Wx2 and 220Wx1 at 4 Ohms in three channel configuration (3-Ch).
Differently from what occurs with other amplifiers, LRx 4.300 is not blocked by protection systems
immediately below 2 Ohms. Its exclusive “Overload Limiter” circuit allows it to go on working, limiting
output power and pointing out how hard the applied load is by the “Limit” LED blinking.
Its big power reserve, its constant control at low frequencies and its exquisite timbre qualities make it an
ideal amplifier to realise systems designed to attain outstanding musical features and very high sound
pressures (SPL).
LRx 4.300 has a bypass subsonic filter (24dB/Oct.) with adjustable frequency, pre-set at 20Hz. It also has a
HI-PASS (12dB/Oct.) and a LO-PASS (12-24dB/Oct.) Butterworth crossover with independent frequencies;
they can be bypassed through a switch under the setting panel, in the amplifier bottom. Another switch
under the setting panel permits to configure the preamplified output (OUT) as additional input (IN B), in
order to accept the source second output for Rear system.
INSTALLATION
AMPLIFIER FIXING
ELECTRIC CONNECTIONS
CAUTION!
For the system safer protection, we
recommend the use of a strip fuse
on the cable that connects the
battery positive pole to the
amplifier POWER (+) terminal block.
This fuse has to be installed about
10 cm far from the battery; its value
will have to be equal or slightly
higher (+10% approx.) than
consumption @13.8 VDC, according
to the different configurations (see
“Technical features”).
It will have to be equal to the sum of
the values of all fuses in case system
consists of several amplifiers or in
case amplifiers have several fuses.
In case LRx amplifiers are used in extremely difficult conditions (very low loads) or in installations where
space is too narrow and their heat sink cooling is not enough, they can be employed together with CLK2
cooling system (optional). It is a system made of two units to apply onto the amplifier sides; each of
them is provided with an electronically controlled fan that allows the amplifier thermal stabilisation (see
“CLK2 – LRx Cooling Kit”).
Protection includes:
• RGP (Resettable Ground Protection) circuit; in case a short circuit occurs between loudspeakers outputs
and car chassis, it detects a high current flow in the pre-input ground and acts by putting the amplifier in
stand-by, protecting its circuitry;
• a device against short circuits and against DC in the outputs, to protect loudspeakers;
• a device that detects the amplifier temperature excessive increase and stops its functioning until
optimal conditions occur again.
Once the causes which implied protection circuits intervention have been checked and solved, the
amplifier is reset by switching it off and on again.
The amplifier is also provided with another general protection which is insured by an internal strip fuse,
very easy to reach.
Optional:
The following devices are available upon request:
1 – Three kits for subwoofer volume remote control:
• VCR01 and VCRAK (analogue and specific for subwoofer);
• VCRDK (digital; it can be used for master volume control or for level control of any ways in a
multichannel system).
2 - CLK2 cooling system.
4
LRx 4.300 FUSE: 30A
21
IN-OUT PANEL
INSTALLATION
FUNCTIONS
LOGO ROTATION
1 - Remove the transparent
cover which protects
controls and then the 4
screws which block the
metal plate by using
multispanner.
2 - Remove the plate without damaging the
silkscreen printed panel which will have to
stay on. We suggest that you seize both plate
grips with your hands and pull them by
blocking the silkscreen printed panel with
your fingers against the amplifier chassis at
the same time. This will permit to remove the
plate from the panel without damages.
POWER
IN OUT
REMOTE
1
CH A/HI-PASS, CH B/LO-PASS
Power outputs of the amplifier left and right channels.
Connect the speakers cables to these outputs according
to polarity. Terminal blocks accept cables up to 9 A.W.G.
max (see “audison cable products for electronic
connections” as far as their size is concerned). We
recommend the use of audison cable products.
Please use +L and –R terminal blocks called mono in
order to connect every channels pair in bridge and
exploit the maximum power insured by this
configuration.
2
FUSE
PPS (Phantom Power Supply)
Power supply socket for audison
external audio accessories.
2
3 - Remove the strip with
audison logo.
3
1
4 - Put the strip back again after turning it, so
that audison logo is upside down.
3
1
4
IN A
Left (L) and right (R) inputs of the amplifier A channels. The preamplified outputs
(PRE OUT) of a source (head unit, CD player, DAT, etc.) or of an external electronic
crossover must be connected to them.
Connect only the right (R) channel input in order to use the amplifier in mono.
5 - Mount the plate
back by fixing it
through the screws;
then, re-assemble the
transparent cover
which protects
controls.
20
4
IN B/OUT
Left (L) and right (R) inputs of the amplifier B channels or amplifier HI/BYPASS preamplified
outputs (see “Configurations table”). Connect only the right (R) channel input in order to use the
amplifier in mono.
5
POWER SUPPLY PANEL
CONFIGURATION EXAMPLES
FUNCTIONS
FRONT+REAR+SUB
1
REMOTE IN
Terminal to connect Remote cable, which comes from the
source and which controls the amplifier switching on. Applied
voltage must be between 7 and 15VDC.
Pre Out
Front
2
Rear
POWER
IN OUT
REMOTE
1
LRx 4.300
Config. 1
LRx 1.400
Config. 4
3
FUSE
2
4
+
+
5
REMOTE OUT
Terminal to repeat the switching on control (Remote IN) coming from the source. It is used to
switch on another amplifier or device in the system simultaneously. Available voltage is the same
as the one applied on Remote IN.
+
+
+
Subwoofer
+
Subwoofer
Woofer
3
Woofer
Midrange
Tweeter
Midrange
VCR (optional kit)
Terminals to connect VCR01/VCRA/VCRD adjuster included in VCR01K/VCRAK/VCRDK volume
remote control kits.
Tweeter
Rear
4
LRx 4.300
FUSE (30A)
Strip fuse. It insures the amplifier general protection. In case the fuse breaks down, please replace
it by respecting its original value.
CAUTION: If you want to protect the system even more, please put a strip fuse onto the cable
which connects the battery positive pole to the amplifier POWER (+) terminal block (see “Electric
connections”).
Config. 1
+
+
+
+
5
Woofer
POWER
Terminal blocks for the amplifier power supply cable connection. Connect positive and negative
poles according to indicated polarities. Holes have 8mm diameter and accept cables up to 3 A.W.G.
max. In order to get the best current transfer, please use power supply cables with as big a section
as possible. audison cable catalogue offers you a complete range of such products which can
satisfy whatever demands; you can also find Maincrimp terminals in it. We strongly recommend
their use because they contain the cable non protected end and allow the terminal block to fasten
all its useful section.
6
Woofer
Midrange
Tweeter
Midrange
Tweeter
Front
19
POWER SUPPLY PANEL
CONFIGURATION EXAMPLES
FRONT+SUB
FUSE REPLACEMENT
Pre Out
LRx 4.300
Config. 1
B Ch: mono (
1 - Open the transparent cover by pushing the two teeth in
its lowest corners to the direction indicated by the arrows.
)
+
+
+
Subwoofer
Tweeter
Woofer
Woofer
Tweeter
2 - Remove the screws which fasten the fuse to eliminate
pieces of the broken one; prevent them from going into the
device.
Front R
Front L
FRONT + REAR + SUB
Pre Out
Rear
Sub
LRx 4.300
LRx 2
Config. 3
+
Config. 2
B Ch: mono (
+
)
+
+
Tweeter
Tweeter
3 - Check the value of the new fuse to assemble, then fix it by
gradually and alternately fastening the two screws. This will
avoid voltage drops along the line and will make the device
perfect functioning easier.
Front
+
Subwoofer
Woofer
Woofer
Rear
Tweeter
Woofer
Tweeter
Front L
18
Woofer
4 - Close the transparent cover.
Front R
7
CONTROLS PANEL
CONFIGURATIONS
FUNCTIONS AND CONTROLS
CONFIGURATIONS TABLE
LRx 4.300 can be configured as follows:
Config. 1 = Front (Hi 12 dB) + Sub: (Lo 12/24 dB); IN A (1 IN) – Pre Out (Hi 12 dB)
Config. 2 = Front (Hi 12 dB) + Sub: (Lo 12/24 dB) ; IN A-B (2 IN) – Ch. B mono (Lo 12/24 dB)
Config. 3 = Ch. A (Full Range) + Ch. B (Full Range); IN A (1 IN); Pre Out (Full Range)
Config. 4 = Ch. A (Full Range) + Ch. B (Full Range); IN A+B (2 IN); Pre Out (Full Range)
1
LIMIT (orange LED)
It indicates the Overload Limiter circuit is on.
Caution:
When this led is on (although sporadically), it means the applied load is a hard one. The activation
of Overload Limiter circuit (output power limiter) will anyway allow the amplifier to function
without distortions. In case Overload Limiter gets on too frequently (at every power peak), you will
need to check if there are any failures or a too hard load (that’s to say impedance is about 50%
lower than the minimum recommended one). The amplifier can go on functioning in these
conditions but power will inevitably decrease.
CONFIG.
1
2
1
3
2
11
4
2
ON (green LED)
It indicates the
amplifier is on.
3
10
4
9
5
8
6
7
CH B-LO
CH A-HI
F1
F2
12dB
12dB
IN B/ PRE OUT
12dB
PRE
OUT
1IN
2IN
IN B
OFF
ON
1IN
2IN
PRE
OUT
OFF
ON
1IN
2IN
IN B
OFF
ON
1IN
2IN
12dB
12dB
F1 Slope
CONTROLS PANEL DIAGRAM AND CONFIGURATION SWITCHES
3
A CHANNELS (Level)
It adjusts the amplifier A channels input sensitivity and sets its output level.
8
IN-SELECT
ON
F2
24dB
X-OVER
OFF
F1 Slope
F1
F2
24dB
17
CONTROLS PANEL
CONFIGURATIONS
BLOCK DIAGRAM
4
8
B CHANNELS (Level)
It adjusts the amplifier B channels input
sensitivity and sets its output level.
F1 SLOPE
It permits to choose LO-PASS filter slope
between 12dB/Oct. (stereo) and 24dB/Oct.
(mono, L+R).
5
9
A CHANNELS (Stereo/Mono)
It permits to configure A channels outputs
signal as stereo or mono.
F1
It permits to adjust LO-PASS filter cut-off
frequency between 40 Hz and 5 kHz.
6
10
B CHANNELS (Stereo/Mono)
It permits to configure B channels outputs
signal as stereo or mono.
F2
It permits to adjust 12dB/Oct. HI-PASS
filter cut-off frequency between 40 Hz and
5 kHz.
7
SUBSONIC
It permits to eliminate subsonic
frequencies; these sounds cannot be heard
by human ears but cause useless and
damaging stress to amplifier and speakers.
Subsonic filter can be bypassed (BYPASS)
and it is pre-set at 20 Hz. Its cut-off
frequency can be adjusted between 16
and 32 Hz through 4 Hz steps; this occurs
by replacing the special resistors located
into a socket which can be reached
through the setting panel in the amplifier
bottom.
16
11
SAFETY (red LED)
It indicates that the amplifier protection
circuits are on. In order for the amplifier to
work again, you need to switch the
system off and then on after 10 seconds
at least. We recommend to check all
connections before switching the
amplifier on again.
If LED stays on, please contact Audison
authorised after sale centres.
9
SETTING PANEL
ACCESSORIES
Installation:
FUNCTIONS
It permits to reach the switches for the amplifier configuration, the resistors to set subsonic filter cut-off
frequency and to insert VCA modules for the subwoofer volume remote control.
Setting panel
Remote
First fan
Second fan
1 - Remove the setting panel in the
amplifier bottom in order to carry out
operations.
2 - Once operations have
been carried out, please
close the setting panel.
Remote
IN
Remote
OUT
+
POWER
AMPLIFIER CONFIGURATION
LRx 4.300 configuration occurs through two switches, IN SELECT and X-OVER, located under the setting
panel.
•IN SELECT switch (1 IN - 2 IN) permits to use the preamplified output (OUT) as additional input (IN B). In
this case, you will be able to realise a Front + Sub system, where IN A input drives Front, while IN B input
accepts the possible subwoofer output, to be filtered at 24dB through F1 Slope switch in the controls
panel and to be adjusted through the head unit Fader. IN B input can also
be used to make a full range, Front-Rear system, which will be driven by
two full range signals by bypassing crossovers (X-OVER on OFF). These
signals will have to be suitably filtered through external crossovers.
+
Battery
12 V
•X-OVER switch activates (ON) the two Lo-Pass and Hi-Pass filters,
indicated by F1 and F2 respectively in the controls panel. When F1 and F2
crossovers are off (X-OVER on OFF), you have full range signals on the
amplifier power outputs.
10
15
Ground
SETTING PANEL
ACCESSORIES
CLK2 – LRx Cooling Kit
SUBSONIC FILTER CUT-OFF FREQUENCY MODIFICATION
This cooling system is specially designed to provide LRx amplifiers with the right working
temperature.
CLK2 should be used when LRx amplifiers work in extremely hard conditions (very low loads) or in
installations where space is too narrow and heat sink cooling is not enough. It consists of two units to
apply onto the amplifier sides; each of them is provided with an electronically controlled fan. Its
intervention depends on a thermal sensor that starts the system as soon as LRx heat sink reaches
45°C. The same sensor is connected to a special circuit which controls the two fans speed progressive
increase when temperature increases, too.
Air flux constant control allows the amplifier very good thermal stabilization and limits noise.
Subsonic filter is pre-adjusted at 20 Hz. In order to modify this value, please act according to what
follows.
Procedure:
5 mm
Replace FS1, FS2, FS3, FS4 resistors
according to the values in the setting
panel table.
10 mm
Remark: Cut the new resistors
rheophores according to the
size in the picture.
VCA-VCA1D MODULES INSERTION
LRx 4.300 can accept one of the three optional kits which allow the subwoofer volume remote
control: VCR01K, VCRAK or VCRDK.
These kits have a specific module, VCA or VCA1D, to insert into the amplifier through the setting
panel.
REMARK: Sub volume remote control function is on only when X-OVER switch, in the setting panel, is ON.
Installation:
1 - Remove BYP12 bridge.
2 - Insert VCA/VCA1D module.
- Insertion key. It prevents the module
from being inserted in the wrong way.
14
11
ACCESSORIES
TECHNICAL FEATURES
VCR01K,VCRAK and VCRDK
SIZE FOR FIXING
375 mm
119 mm
176 mm
342 mm
LRx 4.300 can accept one of the optional kits that allow the subwoofer volume remote control.
VCR01K and VCRAK are analogue and special for sub; VCRDK is digital and can be used for master
volume control or for level control of any ways in a multichannel system.
These kits are available as accessories and consist of three elements:
1) Volume adjuster (VCR01/VCRA/VCRD);
2) VCA/VCA1D module to put inside the amplifiers;
3) Wire to connect VCR01/VCRA/VCRD adjusters to the proper sockets in the amplifier rear panel and
to the car lights switch, in order to light it up.
Install VCR01/VCRA/VCRD adjusters in a place you can easily and comfortably reach, according to
the following connection diagram.
POWER
IN OUT
REMOTE
* Drilling dimensions for fixing
FUSE
Remote Out
LRx 4.300
Yellow/White
Output power (RMS) @ 13.8 VDC; THD 1%
- A config.: . . . . . . . . . . . . . . . . . . . . 65W x 4 (4 Ohms)
- B config.: . . . . . . . . . . . . . . . . . . . 105W x 4 (2 Ohms)
- C config.: . . . . . . . . . . . . . . . . . . . 210W x 2 (4 Ohms)
- D config. (3Ch.): . . . . . 65Wx2 (4 Ohms) + 220Wx1
(4 Ohms)
POWER SUPPLY
Voltage: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 ÷ 15 VDC
Idling current: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.7 A
Idling current when off: . . . . . . . . . . . . . . . . 0.02 mA
Consumption @ 13.8 VDC
(Max Musical Power):
- A config. (see Output Power): . . . . . . . . . . . 16.5 A
- B config. (see Output Power): . . . . . . . . . . . . 32.5 A
- C/D config. (see Output Power): . . . . . . . . . . . 28 A
FILTERS/INPUTS
IN A (Front):
Bypass/ 12dB/Oct. Hi-Pass
(40 ÷ 5000 Hz)
IN B (Sub):
Bypass/ 12-24dB/Oct. Lo-Pass
(40 ÷ 5000 Hz)
Subsonic:
Bypass/ 24dB/Oct. Hi-Pass, 16÷32 Hz
(pre-set at 20 Hz)
Pre Out (IN A):
12dB/Oct. Hi-Pass (40 ÷ 5000 Hz)
Inputs: . . . . . . . . . . IN A (Front) - IN B (Sub/Pre Out)
AMPLIFIER STAGE
Distortion – THD (1kHz): . . . . . . . . . . . . . . . . 0.009 %
Bandwidth (-3dB): . . . . . . . . . . . . . . . . . 4 Hz ÷ 85 kHz
S/N ratio(A weighed @ 1V): . . . . . . . . . . . . . . 105 dB
Damping factor (1 kHz, 4 Ohms): . . . . . . . . . . . . 240
Input sensitivity: . . . . . . . . . . . . . . . . . . . 0.2 ÷ 5 VRMS
Input impedance: . . . . . . . . . . . . . . . . . . . . . 15kOhms
Load impedance:
- 4 Ch. stereo: . . . . . . . . . . . . . . . . . . . . . . . 4 – 2 Ohms
- 2 Ch. mono in bridge: . . . . . . . . . . . . . . . . . 4 Ohms
OTHER FUNCTIONS
Remote IN: . . . . . . . . . . . . . . . . . . . 7 ÷ 15 VDC – 1 mA
Remote OUT: . . . . . . . . . . . . . . . . . . . 12 VDC – 10 mA
Auxiliary power supply (PPS): . ±12 VDC – 300 mA
IN VCR (SUB volume)
VCA/VCA1D attenuation: . . . . . . . . . . . . . . . . 100 dB
Fuse: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 A
Nominal output power (RMS)
NP@ 12VDC; THD 0.3%: . . . . . . . . 60W x 4 (4 Ohms)
MAX SIZE (L x H x D): . . . . . . . . . 176 x 56 x 375 mm
WEIGHT: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.6 kg
12
Yellow/White
Blue
VCR 01
0
Control
min
max
VCR01
VCRD/VCRA
Black
Black
Red
FUSE
(250mA)
Ground
Red
FUSE
(250mA)
Orange
Lights
switch
Ground
-
+
Battery
13