DeLonghi DEDW97FI Operating instructions

DeLonghi
DW97AU
Dear Customer,
Please read this User Information carefully and keep it
to refer to at a later date.
Pass it on to any subsequent owner of the appliance.
This manual contains sections of safety instructions,
operating instructions,installation instructions
and trouble shooting tips .
Carefully reading it before using the dishwasher will help
you to use and maintain the dishwasher properly.
Control Panel......................................................3
Dishwasher Features............................................3
Water Softener....................................................4
Rinse Aid.........................................................5, 6
Detergent........................................................7, 8
Not suitable for the dishwasher............................11
At the end of the wash cycle ................................12
Wash Cycle Table...............................................13
Setting the programme.......................................14
Forget to add a Dish................. ........ ...................15
Filtering System..................................................16
Caring for the Dishwasher..............................16, 17
To review the section on Troubleshooting Tips
will help you to solve some common problems
by yourself and not need to ask for the help of
professional technicians.
Please carefully read the installation instruction ....18
Aesthetic panel's dimensions and installation ........18
Tension adjustment of the door spring ................20
Connection of drain hoses...........................................21
Dishwasher installation steps..............................22
Installation the plinth .............................. . 23
Water Connection...............................................25
The manufacturer, following a policy of constant
development and up-dating of the product, may
make modifications without giving prior notice.
Before calling for service...............................27, 28
Error codes..................................................29,30
Under certain conditions, Hydrogen gas may be produced in a hot-water system that has not been used for two
weeks or more. HYDROGEN GAS IS EXPLOSIVE.If the hot-water system has not been used for such a period,
before using the dishwasher turn on all hot-water faucets and let the water flow from each for several minutes.
This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame
during this time.
• Do not abuse, sit on, or stand on the door or dish rack of the dishwasher
• Do not operate your dishwasher unless all enclosure panels are properly in place. Open the door very
carefully if the dishwasher is operating. There is a risk of water squirting out.
• Do not place any heavy objects or stand on the door when it is open.
• When loading items to be washed:
o Locate sharp items so that they are not likely to damage the door seal;
o Load sharp knives with the handles up to reduce the risk of injury ;
o Warning knives and other utensils with sharp points must be loaded in the basket with their points down
or placed in a horizontal position.
• Check that the detergent receptacle is empty after completion of the wash cycle.
• Do not wash plastic items unless they are marked dishwasher safe or the equivalent. For plastic items not
so marked, check the manufacturer's recommendations.
• Use only detergent and rinse additives designed for an automatic dishwasher. Never use soap, laundry
detergent, or hand washing detergent in your dishwasher.
• Other means for disconnection from the supply must be incorporated in the fixed wiring with at least 3mm
contact separation in all poles.
• Keep children away from detergent and rinse aid, keep children away from the open door of the dishwasher,
there could still be some detergent left inside.
• Young children should be supervised to ensure that they do not play with the appliance.
• The appliance is not intended for use by young children or infirm persons without supervision.
• Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact
with skin and eyes and keep children away from the dishwasher when the door is open.
• The door should not be left in the open position since this could present a tripping hazard.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service representative or a
similarly qualified person in order to avoid a hazard.
• Please dispose of packing materials properly.
• Use the dishwasher only for its intended function.
• During installation, the power supply must not be excessively or dangerously bent or flattened.
• Do not tamper with controls.
• The appliance is to be connected to the water mains using new hose sets and the old hose-sets should not
be reused.
1
Dispose of the dishwasher packaging material correctly.
All packaging materials can be recycled.
Plastic parts are marked with the standard international abbreviations:
¾PE
for polyethylene, e.g. sheet wrapping material
¾PS
for polystyrene, e.g. padding material
¾POM
¾PP
¾ABS
polyoxymethylene, e.g. plastic clips
polypropylene, e.g. Salt filler
Acrylonitrile Butadiene Styrene, e.g. Control Panel .
Warning!
Packaging material could be dangerous for children!
For disposing of package and the appliance please go to a recycling centre.
Cardboard packaging is manufactured from recycled paper and should be dis posed in the
waste paper collection for recycling.When disposing of any dishwasher please remove the
door or make the door closing device unusable.
By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product.
For more detailed information about recycling of this product, please contact your local
city office and your household waste disposal service.
2
To get the best performance from your dishwasher,read all operating instructions before using it for the
first time.
O FF
ON
1
2
3
2
ON/OFF Button: To turn on/off the power supply.
2
Power on light: To come on when Power ON/OFF
button is pressed down.
3
Half Wash Key: Button to select Half Wash.
(It means that the lower spray arm does not run,
so you should load the upper basket only)
4
Delayed Start Button: Press this button to set the
delayed hours for washing. You can delay the start
of washi ng up to 24 hours. One press on this
button delays the start of washing by one hour.
DE LAY
4
6
5
5
Display Window: delay time, running indicator,
faut codes and etc.
6
Program Key-press:To select washing program
when press the Key-p ress.
Back View
Front view
6
1
2
3
7
4
8
5
9
10
11
12
13
on
OFF
O ff
ON
1
1
2
3
4
Upper Basket
Spray Arms
Lower Basket
Main Filter
2
P RO G.
DE LA Y
5
6
7
8
Detergent Dispenser
Cup Shelf
Silverware Basket
Coarse Filter
3
9 Turbo dry
13
10 Rinse Aid Dispenser
11 Drain pipe connector
12 Inlet pipe connector
Tray assembly.
Before usi ng your dishwasher for the first time:
A. Set the water softener
B. Pour 1/2 litre of water inside the salt container and then fill with dishwasher salt
C. Fill the rinse aid dispenser
D. Function of detergent
The water softener must be set manually, using the water hardness dial .
The water softener is designed to remove minerals and salts from the water, which would have
a detrimental or adverse effect on the operation of the appliance. The hi gher the
content of these minerals and salts, the harder your water is. The softener should be
adjusted according to the hardness of the water in your area. Your local Water Authority
can advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjusting the amount of salt consumed based on
the hardness of the water used. This is intended to optimize and customize the level of
salt consumpti on so that the salt consumption could be set proceed as follows:
1. Unscrew the cap from the salt container
2. There is aring on the container w ith anarrow on it (see
figure to the side), if necessary, rotate the ring in the
anticlockwise direction from the “-”Setting toward the
+
“ ”sign, based on the hardness of the water being used.
It i s recommended that adjustments should be made in
accordance with the following schema:
WATER HARDNESS
dH
fH
Clark
mmol/l
0~8
0~14
0~10
0~1.4
Selector Position
Salt consumption
(gram/cycle)
Auto nomy
(cycles/1.2kgs)
/
0
/
8~22
14~39
10~28
1.4~3.9
-
20
60
22~45
39~80
28~56
3.9~8
Mid
40
30
>45
>80
>56
>8
+
60
20
Note:1 ° dH=1.25 ° Cl ark=1.78
° fH=0.178mmol/l
° dH : German degree
° fH : French degree
° Clark: British degree
Contact your local water board for information on the hardness of your water supply.
4
Always use salt intended for use with dishwasher.
The sal t container is locat ed beneath the lower rack and should be filled as foll ows:
Atte ntion!
Only use salt specifically designed for use in dishwa shers! All other t ypes of
salt not spe ci fically designed for use in a dishwasher, e specially table salt, will
damage the water softener. In case of dam ages caused by the use of unsui table
salt the m anuf acturer does not give any warranty nor is liable for a ny cause d
damages.
Only fill with salt just before starting one of the complet e washi ng programmes.
This wi ll prevent a ny grains of salt or salty wa ter, which may have been spli t,
rem ai ni ng of the bottom of the machi ne for a ny period of tim e, which ma y ca use
corrosion.
Afte r the first wash cycle the control panel light expires.
A Remove the lower basket and then unscrew and remove the cap from the salt container.
B If you are filling the container for the first time, fill 2/3 of its volume with water (around 500ml).
C Place the end of the funnel (supplied) into the hole and introduce about 1,2kg of salt. It is
Normal for a small amount of water to come out of the salt container.
D Carefully screw the cap back on.
E Usually, the salt warning light will be off in 2-6 days after the salt container be filled with salt.
NOTE:
1. The salt container must be refilled when the salt warning light in the control panel comes on.
Though the salt container is filled enough, the indicator light may not black out
before the salt fully dissolve.
If there is no salt warning light in the control panel (for some models) , you can judge when to load
the salt into the softener by the cycles that the dishwasher had run .
2. If there are spills of the salt, a soak program could be run to wipe them out.
Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot
and streak free drying.
Only use branded rinse aid for dishwasher. Never fill the rinse aid dispenser with any
other substances (e.g. dishwasher cleaning agent, liquid detergent). This would damage
the appliance.
5
You can judge the amount of rinse-aid by the color of the optical level indicator "D" located next to the cap. When the rinse-aid
container is full, the whole indicator will be dark .As the rinse-aid diminishes, the size of the dark dot decreases. You should never
let the rinse aid get below 1 / 4 full.
D (Rinse-Aid indicator)
As the rinse aid diminishes, the size of the black dot
on the rinse aid level indicator changes, as illustrated below.
Full
3 / 4 full
1 / 2 full
1 / 4 full - Should refill to eliminate spotting
Empty
1
2
3
To open the dispenser, turn the cap to the "open" (left) arrow and lift it out.
Pour the rinse aid into the dispenser, being careful not to overfill.
Replace the cap by inserting it aligned with "open" arrow and turning it to the closed (right) arrow.
The rinse aid is released during the final rinse to prevent water from forming droplets on your dishes
that can leave spots and streaks. It also improves drying by allowing water to sheet off the dishes.
Your dishwashers are designed to use liquid rinse aids. The rinse aid dispenser is located inside the
door next to the detergent dispenser. To fill the dispenser, open the cap and pour the rinse aid into
the dispenser until the level indicator turns completely black. The volume of the rinse aid container
is about 140ml.
Be careful not to overfill the dispenser, because this could cause over sudsing. Wipe away any spills
with a damp cloth. Don't forget to replace the cap before you close dishwasher door.
Attention!
Clean up any rinse aid split during filling with an absorbent cloth to avoid excess foaming
during the next wash.
Adjust lever
(Rinse)
The rinse aid dispenser has 6 settings. Always start with the dispenser set on
“2”. If spots and poor drying are problems, increase the amount of rinse aid dispensed
by removing the dispenser lid and rotating the dial to “3”. If the dishes still are not
drying properly or are spotted, adjust the dial to the next higher number until your dishes
are spot-free. We suggest you to set on “2”(Factory value is “2”)
NOTE:
Increase the dose if there are drops of water or lime spots on the dishes after washing.
Reduce it if there are sticky whitish streaks on the dishes or a bluish film on glassware or
knife blades.
6
Detergents with its chemical ingredients are necessary to remove dirt, dissolved dirt and
transport it out of the dishwasher. Most of commercial quality detergents are suitable
for this purpose.
Concentrated Detergent
Based on their chemical composition, dishwasher detergent can be:
conventional, alkaline detergents wi th caustic components
low alkaline concentrated detergents with natural enzymes
The use of “normal” washing programmes in conjunction with concentrated detergents
reduces pollution and is good for your dishes; these wash programmes are specially matched
to the dirt-dissolving properties of the enzymes of the concentrated detergent. For this reason
“normal”wash programmes in which concentrated detergents are used can ac hieve the
same results that can otherwise only be achieved using “intensive” programmes.
Detergent Tablets
Detergent tablets of different brands dissolve at different speeds. For this reason some
detergent tablets cannot dissolve and develop their full cleaning power during short
programmes. Therefore please use long programmes when using detergent tablets, to
unsure the complete removal of detergent residuals.
Detergent Dispenser
The dispenser must be refilled before the start of each wash cycle following the instructions
provided in the Wash Cycle Table. Generally, only one tablespoon of detergent is needed for
a normal wash load. Also, more heavily soiled items need more detergent. Always add the
detergent just before starting dishwasher, otherwise it could get damp and will not di ssolve
properly.
Amount of Detergent to Use
Please refer to the 'WASH CYCLE TABLE' on page 15 for the correct amount of detergent to use for each cycle
1
2
If the lid is closed: press release button. The lid springs open.
Always add the detergent just before starting each wash cycle.
Only use branded detergent aid for dishwasher.
Dishwasher detergent is corrosive! Take care to keep it out of reach of children.
Proper Use of Detergent
Use only detergent specifically made for use in dishwashers. Keep your detergent fresh
and dry. Don't put powder detergent into the dispenser until you're ready to wash dishes.
7
Filling the detergent container
1
Fill the detergent dispenser with detergent.
The marki ng indicates the dosing levels , as
illustrated on right:
1 Place the detergent for the main wash cycle here.
2
Place the detergent for the pre-wash cycle here.
Please observe the manufacturers dosing and storage
recommendations as stated on the detergent packaging.
Close the lid and press until it locks in place.
If the dishes are heavily soiled, place an additional detergent dose in the pre-wash detergent
chamber. This detergent will take effect during the pre-wash phase.
NOTE:
You find information about the amount of detergent for the single programm es on the
last page. Please aware, that according to the level soiling and the specific hardness of
water differences are possible.
Please observe the manufacturer's recommendations on the detergent packaging.
Turbo drying is a very effective drying system.
The moist, warm air is expelled quickly by a fan
to provide optimum drying results.
8
2
For best performance of the dishwasher, follow these loading guidelines. Features and
appearance of racks and silverware baskets may vary from your model.
Attention before or after Loading the Dishwasher Racks
Scrape off any large amounts of leftover food. It is not necessary to rinse the dishes under
running water. Place objects in the dishwasher in following way:
1.Items such as cups, glasses, pots/pans, etc. are stood upside down.
2.Items with recesses or curves should be placed at a slant to allow the wate r to run off where possible, to avoid water pooling on the dish.
3.They are stacked securely and can not tip over.
4.They do not prevent the spray arms from rotating while washing takes place.
Very small items should not be washed in the dishwasher as they could easily fall out of the racks.
Removing the Dishes
To prevent water dripping from the upper back into the lower back, we recommend that you
empty the lower basket first and then the upper back.
Loading the Upper Rack
The upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cup and saucers, as well as plates, small bowls and shallow pans (as long as they are
not too dirty).
Position the dishes and cookware so that they do not get moved by the spray of water.
2
11
3
14
2
4
2
1
4
2
1
4
9
1
2
3
4
Cups
Glasses
Saucers
Dessert dishes
The upper rack is for more delicate and lighter dishware
such as glasses, coffee & tea cups, saucers, plates, bowls,
and shallow pans (provided these are not too dirty).
Position the dishes and cookware so that they do not get
moved by the spray of water. Always place glasses, cups &
bowls upside down.
NOTE:
POSITION 1
Your dishwasher comes with an adjustable top rack (basket)
pictured at right. Its height can be adjusted by lifting the
handle in a downward or upward direction. (Pls see the
figures on the right: position 1 & positon 2.)
NOTICE:
Ensure the metal rod is located in its correct position.
POSITION 2
*** NOTE ***: The upper rack has side flaps (pictured at left
above basket). There are 4 (2 on each side). These can be
adjusted into 2 positions = position 1 (high) and position 2 (low).
To move the flaps between these positions, locate the large hinges
clip each flap to the upper rack. There are two of these at
either end of each flap. Gently pull both clips off the wire rack
and move the flap to the desired position. be careful if you have
long fingernails!
POSITION 1
The upper position will accommodate items such as glass tumblers (placed beneath flap) and wine
glasses. Wine glasses can be placed upside down so that the neck rests in the grooves at side of flap
with the base of the glass facing upward.
POSITION 2
When the flaps are moved to the lower position, they can be used to hold additional tumblers, cups
and mugs. Always check that you are only placing items on the flaps that will clear the ceiling height
of your dishwasher when you push the rack back in. Be careful with long-stemmed glassware such as
champagne glasses and ensure that these are clear of the top of the dishwasher.
10
We recommend that you place large items which are most difficult to clean into the low er rack:
pots, pans, lids, serving dishes and bowls, as shown in the figure blow.
It is preferable to place serving dishes and lids on the side of the racks in order to avoi d blocking
the rotation of the top spray arm.
Pots, serving bowls, etc. must always be placed top down.
Deep pots should be slanted to allow w ater to flow out.
The bottom rack feature fold down tine row s so that larger or more pots and pans can be loaded.
6
5
4
7
4
3
4
Dessert dishes
5
6
7
Soup plates
Dinner plates
Silverware basket
To improve stacking of pots and pans, the spikes can be folded down.This can be done by initially lifting up the wire rack then folding
down. This should be done when the dishwasher is empty
11
Silverware Basket
Silverware should be placed in the silverware basket with handles at the bottom: If the rack
has side baskets, the spoon should be loaded individually into the appropriate slots,
especially long utensils should be placed in the horizontal position at th e front of the
upper rack.
2
1
1
2
4
4
4
4
2 2 4 2
1 1 4 1
1 1 4 1
2 2 4 3
1 4 1 1 4 1
2 4 2 2 4 2
2
1
5
3
4
4
5
3
1
2
3
4
5
2 33
1 5 5 3
5 5 5 5
3 33 3
5 5 5 5 5 5
2 3 3 3 3
Forks
Soup spoons
Dessert spoons
Teaspoons
Knife
Do not let any item extend through bottom.
Are of limited suitability
Are not suitable
Some types of glasses can become
dull after a large number of washes
Cutlery with wooden, horn china or
mother-of-pearl handles
Plastic items that are not heat resistant
Older cutlery with glued parts that is not
temperature resistant
Bonded cutlery items or dishes
Pewter or cooper items
Lead crystal glass
Steel items subject to rusting
Wooden platters
Items made from synthetic fibres
Silver and aluminium parts have a
tendency to discolour during washing
Glazed patterns may fade if machine
washed frequently
NOTE:
Do not put in items that are dirty of
cigarette ash, candle wax, lacquer or
paint. To avoid damage to your dishes
please only put dishwasher safe products
in your dishwasher.
NOTE:
Please do not overload your dishwasher. There is only space for 14 standard dishes.
Loading cutlery and dishes
Before loading the dishes, please rinse soiled cutlery and dishes before loading to remove large left-over
remnants.
12
When loading the dishes and cutlery, please note:
Dishes and cutlery must not impede the rotation of the spray arms
Load hollow items such as cups, glasses, pans etc. with the opening downwards so that
water cannot collect in the container or a deep base
Di shes and items of cutlery must not lie inside one another, or cover each othe r
To avoid damage to glasses, they must not touch
Load large items which are most difficult to clean into the lower rack
T he upper rack is designed to hold more delicate and lighter dishware such as glasses, coffee
and tea cups
Attention!
Long bladed knives stored in an upright position are a potential hazard and may cause damage to
other dishes. Long and/or sharp items of cutlery such as carving knives must be positioned horizontally
in the upper basket
Possible causes:
Type of glass or manufacturing process. Chemical composition of detergent.
Water temperature and duration of dishwasher programme.
Suggested remedy:
Use glassware or porcelain dishes that have been marked di shwasher-proof by the
manufacturer
Use a mild detergent that is described as kind of dishes If necessary, seek further
information from detergent manufacturers.
Select a programme with as low a temperature.
To prevent damage, take glass and cutlery out of the di shwasher as soon as possible
after the programme has ended.
At the end of a wash cycle, the time display will flash for 8
seconds while the buzzer sound. However, when the delay
start funtion is activated, the time display will flash for
8 seconds, but the buzzer wil l not sound.
13
For normally soiled loads,
such as pots , plates,glasses
and lightly soiled pans.
standard daily cycle.
Pre-wash
pre-wash
wash45 ℃
rinse
rinse68
drying
For the heaviest soiled loads,
such as pots,pans,casserole
dishes and dishes that have
been sitting with dried food
on them for a while.
Pre-wash (45℃)
wash(50℃/ 70℃ )
Rinse
Rinse
Rinse (70℃)
Drying.
5/30 g.
Pre-wash
Pre-wash
Wash (50℃)
Rinse
Rinse (70℃)
Drying.
5/30 g.
For normal soiled loads,such
as plates,glasses,bowls and
lightly soiled pans.
Pre-wash
Pre- Wash
Wash(50℃)
Rinse 60℃
Drying.
2.5/30 g.
Rinse
For dishes that need to be
rinsed and dried only.
Rinse
Rinse (70℃)
Drying.
Rapid
A shorter wash for lightly
soiled loads that do not
need drying.
Wash (40℃)
Rinse(50℃)
Rinse
Soak
To rinse dishes that you
plan to wash later that day.
Rinse
Intensive
For heavy soiled loads,
such as pots , plates,glasses
and li ghtly soiled pans.
standard daily cycle.
(A S/NZS 2007. 1 )
14
3in1
20 g.
Turning on the Appliance
Sta rting a wash cycl e...
1 Draw out the lower basket load the dishes and push back. Repeat for the
up per basket. It is recommended that you load the lower basket first than the
up per one (see the sectio n entitled “L oadi ng the Di sh wash er”) .
2 Po ur in the detergent (see the section entitled “Salt, Det erge nt and Rinse Ai d”).
3 Insert the plug into the socket. The power supply is 220-240
VAC 50 HZ, the specification of the socket is 10 A 2 20-240 VAC.
4 Make sure that the water supply is turn ed on to full pressure.
5 Open the door,press the ON/OFF button,the ON/OFF light will turn o n .
6 Press the "prog." button to select the desired wash cycle (see Wash Cycle table on page14)
7 With a little force to ensure the door is properly closed.
8 When the washing is over, yo u can shu t off the s witch by pres sing ON /OFF b ut ton
NOTE: A click could be heard when the door is closed perfectly. .
PROG.
Premise: A cycle that is underway can only be modified if it
has only been running for a short time. Otherwise, the detergent
may have already been released, and the appliance may have
already drained the wash water. If this is the case, the detergent
dispenser must be refilled (see the section entitled " Loading the
Detergent " ).
Open the door,Press current prog. Button more than three
seconds to cancel the program ,then you can change the
program to the desired cycle setting (see the section entitled
" Starting a wash cycle. . . " ). Then, close the door.
NOTE: If you open the door when washing, the machine
will pause. When you close the door , the machine will
keep on working after 10 seconds.
The 7 program lights shows the state of the dishwasher:
15
A forgotten dish can be added any time before the detergent cup opens.Please be careful when opening the door while the dishwasher is in
operation as hot water may scald you
1
2
Open the door a little to stop the washing.
3
Add forgotten dishes.
After the spray arms stop working,you can open the door
completely.
4
Close the door, the dishwasher will work after ten second.
Filtering System
For your convenience, we have placed the drain pump and filtering system within easy reach inside the tub. There are three
components of the filtering system: the main filter, the coarse filter, and the fine filter.
1
1
Main filter
Food and soil particles trapped by this filter are pulverized by a special jet on the lower spray
arm and washed down the drain.
2
2
Coarse filter
Larger items, such as pieces of bone or glass, that could clog the drain are trapped in the
coarse filter. To remove an item caught in this filter, gently squeeze the tabs on top of this
filter and lift it out.
3
3
Fine filter
This filter holds soil and food residue in the sump area and prevents it from being
redeposited on the dishes during a cycle.
ATTENTION: Do not put the fine filter upside down.
Cleaning the Filters
16
Filter assembly
For best performance and results, the filter assembly must be cleaned. The filter efficiently
removes food particles from the wash water, allowing it to be reci rculated during the cycle. For
this reason, it is a good idea to remove the larger food particles trapped in the filter after each
wash cycle by rinsing the semicircular filter and cup under running water. To remove the filter
assembly, pull on the cup handle in the upward direction. The entire filter assembly should be
cleaned once a week.
To clean the coarse filter and the fine filter, use a cleaning brush. Then, reassemble the filter
parts as shown in the figures left and reinsert the entire assembly in the dishwasher, positioning
in its seat and pressing downward.
The dishwasher must never be used without the filters. Improper replacement of the filter may
reduce the performance level of the appliance and damage dishes and utensils.
Never run the dishwasher without the filters in place. When cleaning the filters do not 'knock' or
use excessive force to clean the filters as if the filters are bent in anyway the performance of the
dishwasher may be effected
Cleaning the Spray Arms
It is necessary to clean the spray arms regularly for hard water chemicals will clog the spray
arm jets and bearings. To remove the spray arms, screw off the nut clockwise to take out the
washer on top of the spray arm and remove the arm. Wash the arms in soapy and warm water
and use a soft brush to clean the jets. Replace them after rinsing them thoroughly.
2
1
1
2
Caring for the Dishwasher
To clean the control panel use a lightly dampened cloth then dry thoroughly. To clean the exterior
use a good appliance polish wax.
Never use sharp objects, scouring pads or harsh cleaners on any part of the dishwasher.
Protect Against Freezing
If your dishwasher is left in an unheated place during the winter, you should:
1.Cut off electrical power to the dishwasher.
2.Turn off the water supply and disconnect the water inlet pipe from the water valve.
3.Drain water from the inlet pipe and water valve. (Use a pan to catch the water)
4.Reconnect the w ater inlet pipe to the water valve.
5.Remove the filter in the tub the bottom and use a sponge to use up w ater in sump.
17
To clean the edge around the door, you should use only a soft warm, damp rag. To prevent
penetration of water into the door lock and electrical components, do not use a spray cleaner
of any kind.
Also, never use abrasive cleaners or scouring pads on the outer surfaces because they will
scratch the fini sh. Some papers towels can also scratch or leave marks on the surface.
OFF
ON
1
2
DE LA Y
PRO G .
Never use a spray cleaner to clean the door panel for it could damage the door lock and electrical components.
After every wash, leave the door slightly ajar so that
moisture and odors are not trapped inside.
When you go on holiday, it is recommened that you run a
wash cycle with the dishwasher empty and then remove
the plug from the socket, turn off the water supply and
leave the door of the appliance slightly ajar. This will help
the seals last longer and prevent odors from forming
within the appliance.
Before cleaning or performing maintenance, always
remove the plug from the socket.
If the appliance must be moved, try to keep it in the vertical
position.If absolutely necessary, it can be positioned on
its back.
To clean the exterior and rubber parts of the dishwasher,
do not use solvents or abrasive cleaning products.
Use only a cloth and warm soapy water.
To remove spots or stains from the surface of the
interior, use a cloth dampened with water and a little
white vinegar, or a cleaning product made specifically
for dishwashers.
One of the factors that cause odors to form in the
dishwasher is food that remains trapped in the seals.
Periodic cleaning w ith a damp sponge will prevent this
from occurring.
The installation of the pipes
and electrical equipments
should be done by professionals.
●
Installation preparation
The installation position of dishwasher should be near the existing inlet and drain hoses and
power cord.
One side of the cabinet sink should be chosen to facilitate the connection of drain hoses of
the dishwasher.
Note: please check the accompanying installation accessories(hook for aesthetic panel and
screw)
18
【Figure1】
90 °
Cabinet dimensions
Less than 5mm
between the top
of dishwasher and
cabinet and the
outer door aligned
to cabinet.
90 °
820mm
580mm
Electrical, drain and
water supply line
entrances
80
100
Space between cabinet
bottom and floor
600 mm
【Figure2】
Dishwasher
Minimum space when
the door is opened
Cabinet
Door of
dishwasher
Minimum space of 50mm
●
1
Aesthetic panel's dimensions and installation
The aesthetic wooden panel could be processed according to the Figure 3.A template has been
included with the dishwasher.
540 ± 0.2
15
40
3.5
8
568 ± 0.2
【Figure3】
The aesthetic panel should
be processed in accordance
with the illustrated dimensions
38
19
254 ± 0.2
(Unit: mm)
250 ± 0.2
594
19
2 Install the hook on the aesthetic wooden panel and put the hook into the slot of the outer door
dishwasher(see figure 4a). After positioning of the panel , fix the panel onto the outer door by
screws and bolts(See figure 4b) .
Hop hook
【Figure4a】
Installation of aesthetic panel
St4 countersunk
head screw
Lower hook
4X18 screw
【Figure4b】
Cover
Installation of aesthetic
wooden panel
Spacer for aesthetic panel
1. take away the cover
2. pin up the screw
3. get back the cover
Hook for aesthetic panel
Outer door of
dishwasher
20
Aesthetic panel
of
●
Tension adjustment of the door spring
The door springs are set at the factory to the proper tension for the outer door. If aesthetic
wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting
screw to drive the adjustor to strain or relax the steel cable(see figure 5).
Door spring tension is correct when
the door remains horizontal in the
fully opened position,yet rises
to a close with the slight lift of a
finger.
rel ax
【Figure5】
Tension adjustment
of the door spring
●
Connection of drain hoses
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
run into the sink, making sure to avoid bending or crimping it. Use the speical
plastic support that comes with the appliance (figure 6). The free and of the hose
must be at a height between 400 and 1000mm and must not be immersed in water
to avoid the back flow of it.ATTENTION: The special plastic hose support must be
solidly fastened to the wall to prevent the drain hose from moving and allowing water
to spill outside the drain.
【Figure6】
SINK
DISHWASHER
POWER OUTLET
Inlet pipe connector Drain pipe connector
FRONT VIEW
Min 100mm
21
●
Dishwasher installation steps
1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer
to the template for positioning of the brackets.
2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to your dishwasher
(Illustration 2) .
3 Connect the inlet hose to the cold water supply .
4 Connect the drain hose. Refer to diagram . (Figure 6)
5 Connect the power cord.
6 Put the dishwasher to slide rails(Illustration4) .
7 Add the condensation strip following instructions on the reverse side of the condensation strip .
8 Place the dishwasher into position.
9 Level the dishwasher. The rear feet can be adjusted from the front of the dishwasher by turning
the screws on the left and right hand side of the cabinet (Illustration 6A). To adjust the front feet,
use a wrench and turn the front feet until the dishwasher is level (Illustration 6B).
10 The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface-secure to the work surface by using two woodscrews ensuring the
dishwasher weight is not being hit by the surface (Illustration 7).
B. Marble or granite work top-secure the bracket to the side panel of the dishwasher and secure
the dishwasher to the furniture housing. Put the rubber cap over the screw (Illustration 8).
2
7
1
5
4
SCREW
CONE GEAR
6A
6B
RUBBER COVER
6
8
SCREW
【Figure 7】
22
●
Installation the plinth
1 Unscrew the tw o screws and remove the plinth from the dishwasher. [Figure 8a]
plinth
[Figure 8a]
screw
2 Unscrew the two screws and adjust the distance of left and right plinth tab to your need.
The adjustable range is from 39mm to 134mm. [Figure 8b]
screw
[Figure 8b]
3 Fix the plinth on the plinth tab. According to your need to adjust the plinth height, the
adjustable range is from 56mm to 122mm. [Figure 8c]
plinth tab
[Figure 8c]
【Figure 8】
23
plinth
Dishwasher must be level for proper dish rack operation and wash performance.
1 Place level on door and rack track inside the tub as shown to check that the
dishwasher is level.
2 level the dishwasher by adjusting the four leveling legs individually.
3 When level the dishwasher, pl ea s e pay attention not to let the dishwasher tip forward .
【Figure 9】
Illustration of feet adjustment
Check
Level
Front
to Back
NOTE:
The maximum adjustment
height of the feet is 20 mm.
Check level
side to side
Please see the rating label to know the rating voltage and connect the dishwasher to the appropriate power supply, a 10 amp fused
circuit is required with copper wire only. A sperate circuit with a circuit breaker serving only this appliance is recommended.
The power outlet should be placed in an adjacent cabinet.
After making sure that the voltage and the frequency values for the current in the home correspond to those
on the rating plate and that the electrical system is sized tor the maximum voltage on the rating plate, insert
the plug into an electrical socket which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate tor the plug, replace the socket, rather than using a adaptors or the
like as they could cause overheating and burns.
Insure proper ground exists before use
„ This appliance must be grounded. In the event
of a malfunction or breakdown, grounding will
reduce the risk of electric shock by providing a
path of least resistance of electric current. This
appliance is equipped with a cord having an
equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate
outlet that is installed and grounded in accordance
with all local codes and ordinances.
24
„ Improper connection of the equipment-
grounding conductor can result in a risk
of electric shock. Check with a qualified
electrician or service representative if you
are in doubt whether the appliance is
properly grounded. Do not modify the plug
provided with the appliance; If it is not fit
for the outlet. Have a proper outlet installed
by a qualified electrician.
The appliance must be connected to the water mains using new hose-sets.
The old hose-sets should not be reused.
Water pressure must be between 0.04 MPa and 1 Mpa.
1
2
3
Pull The safety supply hoses completely out from storage compartment located at rear of dishwasher.
Tighter the screws of the safety supply hose to the faucet.
Turn water fully on before starting the dishwasher.
The Aquasafe is a safety valve system, protecting you from water leaks. If the water inlet hose starts to leak during a wash cycle,
the safety valve cuts off the running water. Do not immerse the water inlet hose or the safety valve in water, because the electrical
cable for the safety valve is in the double-walled water inlet hose.
If the water inlet hose or the safety valve is damaged, remove the main plug immediately.
Do not enlarge or shorten the inlet hose because it contains electrical parts
A hose that attaches to a sink spray can burst if it is installed on the same water line as the dishwasher. If your sink has one, it is
recommended thet the hose be disconnected and the hole plugged.
1 Turn off the water.
the water pressure by depressing the pressure release button. This relieves water pressure and protects you, and the
2 Release
room, from severe splashing.
3 Unscrew the safety supply hose from the tap.
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the
water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and
damage the appliance.
The water supply to the appliance can also be connected to the house hot water line (centralized system, heating system),
as long as it does not exceed a temperature of 60 C. In this case, the wash cycle time will be shortened by about 15 minutes
and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as those for the connection to the
cold water line.
25
●
Start of dishwasher
The followings should be checked before starting the dishwasher.
1
2
3
4
5
6
7
●
The dishwasher is level and fixed
The inlet valve is opened
There are no leaks
The electrical plug and lead is undamaged and connected to the socket correctly
The inlet and drain hoses are not knotted or twisted in any way that will effect the water supply
The inlet and drain hoses are knotted
All packing materials and printings should be taken out from the dishwasher
Attention
After installation please retain this instruction manual for future reference and trouble shooting.
26
Before Calling for Service
Review the charts on the following pages may make you be free of calling for service.
'
'
Fuse blown, or the
circuit breaker acted
Replace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not
turned on
Make sure the dishwasher is turned on and the door is
closed securely.
Make sure the power cord is properly plugged into the
wall socket.
Water pressure is low
Check that the water supply is connected properly and
the water is turned on.
Overflow
The system is designed to detect an overflow. When it
does, it shuts off the circulation pump and turns on the
drain pump.
Some audible sounds are
normal
Sound from soft food shredding action and detergent cup
opening.
Utensils are not secure
in the baskets or something
small has dropped into
the basket
To ensure everything is secured in the dishwasher.
Motor hums
Dishwasher has not been used regularly. If you do not use it
often, remember to set it to fill and pump out every week,
which will help keep the seal moist.
Improper detergent
Use only the special dishwasher detergent to avoid suds.
If this occurs, open the dishwasher and let suds evaporate.
Add 4 litres of cold water to the tub. Close and latch the
dishwasher, then Start the "soak" wash cycle to drain out the
water .. Repeat if necessary.
Spilled rinse agent
Always wipe up rinse agent spills immediately.
Detergent with
colorant was used
Make sure that the detergent is the one without colorant.
Rinse agent dispenser
is empty
Make sure that the rinse agent dispense is filled.
Improper program
Select stronger program
Improper rack loading
Make sure that the action of the detergent dispenser and
spray arms are not blocked by large dishware.
Extremely hard water
Low inlet
temperature
Overloading the
dishwasher
Improper loading
Old or damp powder
detergent
Empty rinse agent
dispenser
Incorrect dosage of
detergent
To remove spots from glassware:
Take out all metal utensils out of the dishwasher.
Do not add detergent.
Choose the longest cycle.
Start the dishwasher and allow it to run for about
18 to 22 minutes, then it will be in the main wash.
Open the door to pour 2 cups of white vinegar
into the bottom of the dishwasher.
Close the door and let the dishwasher complete
the cycle. If the vinegar does not work: Repeat
as above, except use 1/4 cup (60 ml)of citric acid
crystals instead of vinegar.
27
Combination of soft
water and too much
detergent
Use less detergent if you have soft water and select a
shortest cycle to wash the glassware and to get them clean.
Tea or coffee stains
using a solution of 1/2 cup of bleach and 3 cups warm water
to remove the stains by hand.
You have to wait for 20 minutes after a cycle to let the heating
elements cool down before cleaning interior; otherwise, burns
will happen.
Iron deposits in water
can cause an overall film
You have to call a water softener company for a special filter.
Hard water minerals
To clean the interior, use a damp sponge with dishwasher
detergent and wear rubber gloves. Never use any other cleaner
than dishwasher detergent for the risk of foaming or suds.
Dishes block detergent
cups
Re-loading the dishes properly.
Normal phenomenon
There is some steam coming through the vent by the door
latch during drying and water draining.
Aluminum utensils have
rubbed against dishes
Use a mild abrasive cleaner to eliminate those marks.
This is normal
A small amount of clean water around the outlet on
the tub bottom keeps the water seal lubricated.
Overfill dispenser or rinse
aid spills
Be careful not to overfill the rinse aid dispenser.
Spilled rinse aid could cause oversudsing and lead
to overflowing. Wipe away any spills with a damp cloth.
Dishwasher isn' t level
Make sure the dishwasher is level.
Longer inlet time.
The tap is not opened, or water intake is restricted,or water pressure
is too low.
Longer heating time,
but not reaching required temperature
Malfunction of temperature sensor or of heating element.
Overfilled.
Too much inlet water. .
Failure of temperature sensor
Short circuit or break of temperature sensor
Failure of temperature sensor
Open circuit or break of temperature sensor
If overflow occurs, turn off the main water supply before calling a service. If there is water in the base pan because of an overfil l
or small leak, the water should be removed before restarting the dishwashe r.
28
595
820
Height :
Width :
Depth :
Voltage connected Load :
Water pressure:
Hot water connection :
Power supply:
Capacity:
820mm(adjustable+10mm)
595mm
560mm
see rating label
0.04-1.0MPa
max 60 ℃
see rating label
14 Place settings
29