Compaq 154060-002 Installation guide

64-Bit/66 MHz Single Channel Wide
Ultra3 SCSI Adapter
Installation Guide
Second Edition (July 2000)
Part Number 154060-002
Compaq Computer Corporation
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
Notice
© 2000 Compaq Computer Corporation
Compaq, Compaq Insight Manager, ROMPaq, QVision, SmartStart, registered United States Patent and
Trademark Office.
SoftPaq is a trademark of Compaq Information Technologies Group, L.P.
Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation.
All other product names mentioned herein may be trademarks and/or registered trademarks of their
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions contained herein. The
information in this document is subject to change without notice.
THE INFORMATION IN THIS PUBLICATION IS PROVIDED “AS IS” WITHOUT WARRANTY
OF ANY KIND. THE ENTIRE RISK ARISING OUT OF THE USE OF THIS INFORMATION
REMAINS WITH RECIPIENT. IN NO EVENT SHALL COMPAQ BE LIABLE FOR ANY DIRECT,
CONSEQUENTIAL, INCIDENTAL, SPECIAL, PUNITIVE OR OTHER DAMAGES
WHATSOEVER (INCLUDING WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS
PROFITS, BUSINESS INTERRUPTION OR LOSS OF BUSINESS INFORMATION), EVEN IF
COMPAQ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES AND WHETHER
IN AN ACTION OF CONTRACT OR TORT, INCLUDING NEGLIGENCE.
The limited warranties for Compaq products are exclusively set forth in the documentation
accompanying such products. Nothing herein should be construed as constituting a further or
additional warranty.
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Second Edition (July 2000)
Part Number 154060-002
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
Contents
About This Guide
Text Conventions........................................................................................................vi
Symbols in Text.........................................................................................................vii
Symbols on Equipment..............................................................................................vii
Getting Help ............................................................................................................ viii
Compaq Technical Support .............................................................................. viii
Compaq Website .................................................................................................ix
Compaq Authorized Reseller...............................................................................ix
Chapter 1
Introduction
Features.................................................................................................................... 1-1
Wide Ultra3 SCSI Support ...................................................................................... 1-2
PCI ........................................................................................................................... 1-2
SCSI Connectors...................................................................................................... 1-3
SCSI IDs .................................................................................................................. 1-4
Multiple Adapter Installation................................................................................... 1-4
SCSI Termination .................................................................................................... 1-4
SCSI Cables............................................................................................................. 1-5
SCSI Cable Connectors ........................................................................................... 1-6
Chapter 2
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
Items Needed ........................................................................................................... 2-1
Preparing the Server ................................................................................................ 2-2
Opening the Server .................................................................................................. 2-2
Installing the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter.............. 2-2
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
iv
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI
Adapter
continued
Cabling the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter ................ 2-3
External SCSI Connections............................................................................... 2-3
Internal SCSI Connections................................................................................ 2-4
Completing the Installation...................................................................................... 2-7
Updating the Firmware and Installing the Drivers............................................ 2-7
Chapter 3
Installing the Firmware and Software
Upgrading the System ROM.................................................................................... 3-2
ROMPaq Diskettes ........................................................................................... 3-2
Running System ROMPaq................................................................................ 3-3
Installing the Drivers................................................................................................ 3-4
Windows NT 3.51 or 4.0 .................................................................................. 3-4
Windows 2000 .................................................................................................. 3-5
SCO UnixWare 7.x ........................................................................................... 3-6
SCO OpenServer 5............................................................................................ 3-6
Novell NetWare 5.1 .......................................................................................... 3-9
IBM OS/2........................................................................................................ 3-10
Appendix A
Regulatory Compliance Notices
Federal Communications Commission Notice........................................................ A-1
Class A Equipment ................................................................................................. A-2
Class B Equipment.................................................................................................. A-2
Declaration of Conformity for Products Marked with FCC Logo, United
States Only....................................................................................................... A-3
Modifications................................................................................................... A-3
Cables .............................................................................................................. A-3
Canadian Notice (Avis Canadien)........................................................................... A-4
Class A Equipment .......................................................................................... A-4
Class B Equipment........................................................................................... A-4
European Union Notice........................................................................................... A-4
Japanese Notice....................................................................................................... A-5
Taiwanese Notice.................................................................................................... A-5
Appendix B
Electrostatic Discharge
Grounding Methods ................................................................................................ B-2
Index
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
About This Guide
This guide is designed to be used as step-by-step instructions for installation
and upgrades to the Compaq StorageWorks 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter.
WARNING: To reduce the risk of personal injury from electrical shock and
hazardous energy levels, only authorized service technicians should attempt to
install this equipment. Consult the Safety Information and user documentation
provided with your computer before attempting this installation.
Many servers and workstations are capable of producing energy levels that are
considered hazardous and are only intended to be serviced by qualified
personnel trained in dealing with these hazards. Do not remove enclosures or
attempt to bypass any interlocks that may be provided for the purpose of
removing these hazardous conditions.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
vi
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
Text Conventions
This document uses the following conventions to distinguish elements of text:
Keys
Keys appear in boldface. A plus sign (+) between
two keys indicates that they should be pressed
simultaneously.
USER INPUT
User input appears in a different typeface and in
uppercase.
FILENAMES
File names appear in uppercase italics.
Menu Options,
Command Names,
Dialog Box Names
These elements appear in initial capital letters.
COMMANDS,
DIRECTORY NAMES,
and DRIVE NAMES
These elements appear in uppercase.
Type
When you are instructed to type information, type
the information without pressing the Enter key.
Enter
When you are instructed to enter information, type
the information and then press the Enter key.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
About This Guide
Symbols in Text
These symbols may be found in the text of this guide. They have the following
meanings.
WARNING: Text set off in this manner indicates that failure to follow directions
in the warning could result in bodily harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions
could result in damage to equipment or loss of information.
IMPORTANT: Text set off in this manner presents clarifying information or specific
instructions.
NOTE: Text set off in this manner presents commentary, sidelights, or interesting points
of information.
Symbols on Equipment
These icons may be located on equipment in areas where hazardous conditions
may exist.
Any surface or area of the equipment marked with these symbols
indicates the presence of electrical shock hazards. Enclosed area
contains no operator serviceable parts.
WARNING: To reduce the risk of injury from electrical shock hazards,
do not open this enclosure.
Any RJ-45 receptacle marked with these symbols indicates a Network
Interface Connection.
WARNING: To reduce the risk of electrical shock, fire, or damage to
the equipment, do not plug telephone or telecommunications
connectors into this receptacle.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
vii
viii
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
Any surface or area of the equipment marked with these symbols
indicates the presence of a hot surface or hot component. If this
surface is contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow
the surface to cool before touching.
Power Supplies or Systems marked with these symbols
indicate the equipment is supplied by multiple sources of
power.
WARNING: To reduce the risk of injury from electrical shock,
remove all power cords to completely disconnect power from
the system.
Getting Help
If you have a problem and have exhausted the information in this guide, you
can get further information and other help in the following locations.
Compaq Technical Support
You are entitled to free hardware technical telephone support for your product
for as long you own the product. A technical support specialist will help you
diagnose the problem or guide you to the next step in the warranty process.
In North America, call the Compaq Technical Phone Support Center at
1
1-800-OK-COMPAQ . This service is available 24 hours a day, 7 days a week.
Outside North America, call the nearest Compaq Technical Support Phone
Center. Telephone numbers for world wide Technical Support Centers are
listed on the Compaq website. Access the Compaq website at
http://www.compaq.com.
1
For continuous quality improvement, calls may be recorded or monitored.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
About This Guide
Be sure to have the following information available before you call Compaq:
■
Technical support registration number (if applicable)
■
Product serial number (s)
■
Product model name(s) and numbers(s)
■
Applicable error messages
■
Add-on boards or hardware
■
Third-party hardware or software
■
Operating system type and revision level
■
Detailed, specific questions
Compaq Website
The Compaq website has information on this product as well as the latest
drivers and Flash ROM images. You can access the Compaq website at
http://www.compaq.com.
Compaq Authorized Reseller
For the name of your nearest Compaq Authorized Reseller:
■
In the United States, call 1-800-345-1518.
■
In Canada, call 1-800-263-5868.
■
Elsewhere, see the Compaq website for locations and telephone
numbers.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Comments:
Part Number: 154060-002 File Name: a-frnt.doc Last Saved On: 7/21/00 1:42 PM
ix
Chapter
1
Introduction
TM
The Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
contains one low voltage differential (LVD) SCSI channel that interfaces
directly between the server Peripheral Component Interface (PCI) Local Bus
and up to 15 SCSI devices. The adapter supports industry-standard interfaces
and protocols. The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
can be used with all SCSI devices, including Wide Ultra3 SCSI, Wide Ultra2
SCSI, Wide-Ultra SCSI-3, Fast-Wide SCSI-2, and Fast-SCSI-2 devices.
Features
Standard features of the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI
Adapter:
■
Supports universal 32-bit PCI and universal 64-Bit PCI
■
Supports 33 MHz PCI and 66 MHz PCI
■
Supports Wide Ultra3 SCSI, a 16-bit, 40 MHz bus that provides a 160
MB/s data transfer rate
■
Automatically detects and communicates with Wide Ultra3 SCSI, Wide
Ultra2 SCSI, Wide-Ultra SCSI-3, Fast-Wide SCSI-2, and Fast-SCSI-2
devices
■
Contains one 68-pin Wide LVD SCSI internal connector that supports
Wide Ultra3 SCSI, Wide Ultra2 SCSI, Wide-Ultra SCSI-3, and
Fast-Wide SCSI-2
■
Contains one 68-pin Wide Single-Ended (SE) SCSI internal connector
that supports Wide-Ultra SCSI-3 and Fast-Wide SCSI-2
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
1-2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
■
Contains one 68-pin wide SCSI external connector that supports Wide
Ultra3 SCSI, Wide Ultra2 SCSI, Wide-Ultra SCSI-3, and Fast-Wide
SCSI-2
■
Contains one 50-pin narrow SCSI internal connector to support legacy
devices
Wide Ultra3 SCSI Support
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter provides
64-Bit PCI bus master operation and SCSI data transfer rates of up to 160
MB/s, provided that all components are Wide Ultra3 capable. This
combination allows high throughput in many network application
environments, including resource-sharing, database-servicing, and
high-performance backup solutions.
The adapter also supports tagged command queuing, which allows SCSI hard
drives to queue and sort multiple commands, then execute those commands
simultaneously.
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter complies with
ANSI SCSI-3 standards, supporting Wide Ultra3 SCSI, Wide Ultra2 SCSI,
Wide-Ultra SCSI-3, Fast-Wide SCSI-2, and Fast-SCSI-2 devices. The
64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter can support several
different SCSI devices at one time.
PCI
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter interface to the
server processor is the PCI local bus. The PCI bus is a high-performance,
64-bit bus with multiplexed address and data lines. The PCI bus provides a
high-speed (up to 528 MB/s) path between the system unit and peripherals.
Peripheral devices, such as Wide Ultra3 SCSI adapters, benefit the most from
the high I/O performance of the PCI bus.
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter is
backward- compatible in a 32-bit/33 MHz or 64-bit/33 MHz PCI slot.
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter is a PCI bus
master device and conforms to Rev. 2.1 and 2.2 of the PCI Local Bus
Specification.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
Introduction
SCSI Connectors
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter has the
following connectors:
2
3
1
4
6
5
Figure 1-1. 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
1 Internal 50-pin Narrow SE SCSI legacy connector at J4 (cannot be
used simultaneously with 4)
2 TE (Termination Enable) SEC jumper at J6 (should be jumpered)
3 TE (Termination Enable) PRI jumper at J2 (should be left open)
4 Internal 68-pin Wide SE SCSI legacy connector at J5 (cannot be used
simultaneously with 1)
5 Internal 68-pin Wide LVD/SE SCSI connector at J3
6 External 68-pin Wide LVD/SE SCSI connector at J1
The external connector is a standard wide SCSI connector. It is mounted on
the slot panel and accessible through the back of the server. Screwlocks are
provided for securing external SCSI cables to the standard Wide SCSI
connectors.
IMPORTANT: If an SE SCSI device is connected to this controller, any other connected
devices (including LVD devices) will run at the reduced performance level of an SE device.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
1-3
1-4
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
SCSI IDs
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter contains one
SCSI bus that support up to 15 peripherals. The SCSI bus has internal and
external connectors. Peripherals on the bus must have a unique SCSI ID
ranging from 6 to 0, then 15 to 8, with 6 being the highest priority and 8 being
the lowest priority. SCSI IDs on all peripherals must be either manually set
with switches or jumpers on the device itself, or automatically set on Compaq
products that support hot-pluggable drives. The SCSI IDs determine the
priority of the peripheral device when attempting to access the SCSI bus. The
server assigns the SCSI adapter to the highest priority by setting the ID of the
adapter to 7.
Multiple Adapter Installation
The following considerations apply when you install more than one
64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter:
■
Each adapter has one SCSI bus with isolated LVD and SE connectors.
■
Each adapter supports one set of unique SCSI Ids (from 6 to 0, 15 to 8).
Each peripheral on a bus must be assigned its own unique ID.
SCSI Termination
All SCSI buses require termination on both ends of the bus to prevent signal
degradation. The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
supplies the termination on the adapter end of the SCSI bus. Hot plug drives
do not require terminators on the ribbon cable, because terminators are
included on the drive backplane. Non-hot plug internal drives require
terminators on the ribbon cable. Individual SCSI devices in Compaq servers
should not contain bus termination.
Wide Ultra3 and Wide Ultra2 require multi-mode or LVD-only terminators
(rather than SE only terminators used with Wide-Ultra SCSI-3, Fast-Wide
SCSI-2, and Fast-SCSI-2).
External SCSI buses must also be terminated. This termination is supplied in
Compaq external storage systems. Individual SCSI devices in Compaq storage
systems should not contain bus termination.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
Introduction
CAUTION: To prevent boot error messages, the integrated SCSI controller on
the system board of the server must be terminated at all times. If you are using
the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter to replace the
integrated controller, you should leave a terminated SCSI ribbon cable
connected to the system board, even if there are no SCSI devices attached to
this cable.
SCSI Cables
Cables are provided with most Compaq server products that require cabling. If
you find that you need an additional cable or that one was not provided with
your server product, you can order the necessary cables from your local
Compaq Reseller or authorized Compaq Service Provider. See Table 1-1 for
external cable option kit part numbers.
Table 1-1
Compaq External Cable Option Kit Part Numbers
Cable Option Kit
Part Number
Alternate Part Number
VHDCI to Wide SCSI 6 foot
341176-B21
295644-B21
VHDCI to Wide SCSI 12 foot
341177-B21
295645-B21
Wide SCSI to Wide SCSI 6 foot
313375-001
Wide SCSI to Wide SCSI 12 foot
313375-002
NOTE: An internal 68-pin to 50-pin SCSI adapter (part number 199618-001) is also
available.
If the option kit part number for the cable you need is not listed here, or for
additional ordering information, refer to the Compaq website at
www.compaq.com.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
1-5
1-6
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
SCSI Cable Connectors
To identify the various SCSI cables required 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter installation in the various configurations of
Compaq servers, see Figure 1-2.
Keep these characteristics of SCSI cables in mind:
■
External standard Wide SCSI cables have a round wire with securable
connectors, and the connector heads are smaller than 68-pin external
wide SCSI connector heads.
■
Internal SCSI cables have a flat ribbon cable with push-on connectors.
■
Internal 68-pin wide SCSI ribbon cables (Wide Ultra2 SCSI,
Wide-Ultra SCSI-3, Fast-Wide SCSI-2) are narrower than 50-pin SCSI
(Fast-SCSI-2) cables.
■
Compaq SCSI cables are keyed so they cannot be installed incorrectly.
3
1
2
Figure 1-2. Identifying SCSI cable connectors
1 External 68-pin wide SCSI connector
2 Internal 68-pin wide SCSI connector
3 Internal 50-pin narrow SCSI connector
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments: final
Part Number: 154060-002 File Name: b-ch1 Introduction.doc Last Saved On: 7/21/00 1:21 PM
Chapter
2
Installing the Compaq 64-Bit/66 MHz
Single Channel Wide Ultra3 SCSI
Adapter
This chapter discusses the installation of the Compaq 64-Bit/66 MHz Single
Channel Wide Ultra3 SCSI Adapter in a Compaq server.
WARNING: To reduce the risk of personal injury from electrical shock and
hazardous energy levels, only authorized service technicians should attempt to
install this equipment. Consult the Safety Information and user documentation
provided with your computer before attempting this installation.
Many servers are capable of producing energy levels that are considered
hazardous and are only intended to be serviced by qualified personnel trained in
dealing with these hazards. Do not remove enclosures or attempt to bypass
any interlocks that may be provided for the purpose of removing these
hazardous conditions.
Items Needed
■
Torx T-15 screwdriver
■
Compaq SmartStart and Support Software CD
■
Documentation that came with your Compaq server
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
2-2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Preparing the Server
Use the following general guidelines to prepare the server for installation of
the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter.
WARNING: When working with equipment installed in a rack, be sure that the
equipment/rack is stable before beginning.
To prepare the server:
1. Perform a normal system shutdown.
2. Turn OFF the server.
3. Turn OFF all peripheral devices attached to the server.
4. Unplug the AC power cord from the outlet, then unplug it from the
server.
5. Disconnect all peripheral devices attached to the server.
Opening the Server
Before installing 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter,
you must open the server and gain access to the PCI bus expansion slots. For
instructions on opening the server and accessing the PCI slots, refer to the
documentation that came with your server.
After you have accessed the PCI slots, proceed to the next section, “Installing
the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter.”
Installing the 64-Bit/66 MHz Single
Channel Wide Ultra3 SCSI Adapter
Use the following general guidelines to install 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter in a Compaq server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the
internal system components to cool before touching.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Be
sure you are properly grounded before beginning this procedure. See Appendix
B for ESD information.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
6. Locate the PCI bus expansion slots. Refer to the documentation that
came with your server for the specific location of these slots.
7. Depending on your server model, remove the retaining screw or open
the expansion slot latches that secure the PCI slots.
8. Remove the slot cover from the PCI slot. (You may want to save this
protective cover to use if the slot becomes empty again.)
9. Install the adapter into the PCI slot and press it firmly into place. The
contacts on the adapter edge should be fully seated in the system board
connector.
10. Depending on your server model, secure the adapter by replacing the
retaining screw or by closing the slot latch.
To connect the adapter to other devices, proceed to the next section, “Cabling
the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter.”
Cabling the 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter can be
connected to external SCSI devices (located in outside units) or to internal
SCSI devices (located in the server). The following sections provide cabling
information for both external and internal connections.
IMPORTANT: All SCSI devices (except CD-ROM drives) that are on the same SCSI bus
must be either internal to the server or in an external storage system, but not both. When
using both internal and external SCSI devices, connect each type to a separate port.
External SCSI Connections
To connect the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter to
SCSI devices located outside the server, you will need one external SCSI cable
for each channel to which you are connecting.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
2-3
2-4
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Figure 2-1. External SCSI cabling on a Compaq server
To connect to a wide Ultra3 SCSI peripheral, use a standard Wide SCSI-Wide
SCSI cable.
If this cable is not furnished with your Compaq external SCSI device, it can be
obtained from your local Compaq Reseller. See “SCSI Cables” in Chapter 1
for information on ordering the correct cables.
To attach the cable:
11. Attach the appropriate end of the cable to the external peripheral
according to the instructions that came with the device. Make sure to
secure the thumbscrews.
12. Attach the cable to the adapter and secure the thumbscrews.
After your cabling is complete, proceed to “Completing the Installation,” later
in this chapter.
Internal SCSI Connections
Use the information in this section to connect the 64-Bit/66 MHz Single
Channel Wide Ultra3 SCSI Adapter to internal SCSI devices. The most
common cabling scenarios include:
■
Placing hard drives or other devices on a separate SCSI bus
■
Replacing the integrated SCSI controller with 64-Bit/66 MHz Single
Channel Wide Ultra3 SCSI Adapter
■
Connecting additional internal SCSI devices
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
CAUTION: If your server has an integrated Wide Ultra3 SCSI controller, the
controller must be terminated at all times to prevent boot error messages.
IMPORTANT: In order to run in LVD mode (Wide Ultra3), all components, including the
ribbon cable, must be LVD-capable
Placing Hard Drives or Other Devices on a
Separate SCSI Bus
Use the following guidelines if you are using 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter to provide a separate SCSI bus for one or more
devices in the server.
To add a separate SCSI bus, you may need an internal SCSI cable designed
specifically for your server model. Refer to the documentation that came with
your server to determine if you need an additional cable. If the cable was not
provided with your system, you can obtain it from your local Compaq
Reseller. See “SCSI Cables” in Chapter 1 for information on ordering the
correct cable for your product.
13. Remove any devices from the existing SCSI bus that you want to move
to the new SCSI bus.
14. Install any new SCSI devices.
15. Locate the new SCSI cable. Plug one end of the cable into the
appropriate connector on the 64-Bit/66 MHz Single Channel Wide
Ultra3 SCSI Adapter.
IMPORTANT: Do not connect SCSI cables to both internal and external connectors from
the same port. If you have both SE and LVD devices in your server, use a separate port for
each.
For more information on connecting cables, see “Cabling the 64-Bit/66
MHz Single Channel Wide Ultra3 SCSI Adapter,” earlier in this chapter.
16. Attach one or more device connectors on the cable to the SCSI device(s)
or backplane connector.
Proceed to “Completing the Installation,” later in this chapter.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
2-5
2-6
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Replacing the Integrated SCSI Controller
Use the following guidelines if you are replacing the integrated SCSI
controller with the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter:
17. Unplug the original SCSI cable from the system board.
18. Plug the SCSI cable into the appropriate connector on the 64-Bit/66
MHz Single Channel Wide Ultra3 SCSI Adapter.
IMPORTANT: There are two main restrictions on connecting SCSI devices to this
controller.
■
Connectors J1 and J3 can be used for either LVD or SE SCSI devices. However,
connecting an SE device will cause any LVD devices attached to the same controller
to slow down to SE speeds.
■
Connectors J4 and J5 can only be used for SE devices. These two connectors
cannot be used simultaneously.
For more information on connecting cables, see “Cabling the 64-Bit/66
MHz Single Channel Wide Ultra3 SCSI Adapter,” earlier in this chapter.
19. Depending on your server model, you may need to secure the cable by
clipping it to another component in the server. Refer to your system
documentation for specific instructions on internal cabling.
The 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter now supports
the internal SCSI devices. The integrated controller on the system board can
be used to support other SCSI devices. If you are not using the integrated
controller to support other SCSI devices, it must be terminated.
Proceed to “Completing the Installation,” later in this chapter.
Connecting Additional Internal SCSI Devices
Use the following guidelines to connect new SCSI devices to the 64-Bit/66
MHz Single Channel Wide Ultra3 SCSI Adapter. To perform this procedure,
you will need to order an additional SCSI cable appropriate for each type of
device you are connecting to the 64-Bit/66 MHz Single Channel Wide Ultra3
SCSI Adapter. See “SCSI Cables” in Chapter 1 for information on ordering
the correct cable for your server model.
1. Install the additional SCSI device(s) in the server. Refer to the
documentation provided with your system for specific installation
instructions.
2. Plug the new cable(s) into the appropriate connector(s) on the 64-Bit/66
MHz Single Channel Wide Ultra3 SCSI Adapter.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
Installing the Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter
3. Route the cable(s) according to the instructions in your server
documentation.
4. Attach the cables to the new SCSI devices.
Completing the Installation
After all cabling and connections have been completed, reassemble the server
by following these guidelines:
1. Be sure all cables are routed correctly and are not restricting or being
pinched by other components. Refer to your server documentation for
proper routing of the cables for your server model.
2. Reconnect any peripheral devices to the server.
3. Plug the AC power cord into the server, then into a grounded AC outlet.
4. Turn on any peripheral devices attached to the server.
5. Turn on the server.
6. Run the Compaq System Configuration Utility to enable the system to
recognize the new SCSI adapter configuration. You can run this utility
from the System Configuration diskettes, Compaq SmartStart and
Support Software CD, or from your hard drive (if it was previously
installed in the system partition of your boot hard drive).
Updating the Firmware and Installing the Drivers
Software drivers must be installed in the server to enable communication
between the processor and the new 64-Bit/66 MHz Single Channel Wide
Ultra3 SCSI Adapter.
Some Compaq servers also require updated system ROM firmware before they
can take advantage of the new features of 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter. Compaq recommends running the System
ROMPaq Utility to be sure your server has the latest ROM version. For more
on this, see “Upgrading the System ROM,” in Chapter 3.
Proceed to Chapter 3, “Installing Firmware and Software,” to install the
necessary drivers for your operating system and model.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: c-ch2 Installing the Adapter.doc Last Saved On: 7/21/00 1:30 PM
2-7
Chapter
3
Installing the Firmware and Software
This chapter outlines driver installation steps to set up the Compaq
64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter in a server running
any of the following operating systems:
■
Microsoft Windows NT 3.51 and 4.0
■
Microsoft Windows 2000
■
SCO UnixWare 7.x
■
SCO OpenServer 5
■
Novell NetWare 5.1
■
IBM OS/2
After you install the 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI
Adapter in your server, you must complete the installation by upgrading the
system ROM (if necessary) and installing the new drivers for your operating
system. Follow the procedures outlined in this chapter to guide you through
these important steps.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Upgrading the System ROM
System ROM can be upgraded by flashing the ROM using a special Compaq
utility called System ROMPaq. This utility replaces the existing contents of
the ROM with another version stored in a disk file. Use the information below
to access and run System ROMPaq.
ROMPaq Diskettes
The ROMPaq utilities must be run from diskette. The latest version of the
ROMPaq diskette can be created from the Compaq SmartStart and Support
Software CD that was supplied with your 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter option kit. Use the latest version of ROMPaq
because it most effectively supports your new 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter.
Materials Needed
You will need the following items to create a System ROMPaq utility diskette:
■
Compaq SmartStart and Support Software CD (supplied in
64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter option kit)
■
One blank diskette
■
Access to a server with a bootable CD-ROM drive
Creating Diskettes
To create a ROMPaq diskette:
1. Boot the computer from the Compaq SmartStart and Support Software
CD.
2. From the Compaq System Utilities screen select Create Support
Software.
3. At the Diskette Builder screen, select the appropriate option for your
server model.
4. Follow the instructions on the screen to create the ROMPaq diskette.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
Installing the Firmware and Software
Running System ROMPaq
System ROMPaq is used to update the firmware in Compaq servers. The
64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter has enhanced
capabilities, and many existing servers may not be able to take advantage of
these capabilities without updated firmware. Since it is difficult to determine
when the firmware needs to be updated, Compaq recommends that you run the
latest System ROMPaq on all servers when installing a 64-Bit/66 MHz Single
Channel Wide Ultra3 SCSI Adapter.
To run System ROMPaq, perform the following steps:
1. Place the System ROMPaq diskette in the server diskette drive.
2. Boot the server by turning on the power.
3. Press Enter at the Welcome screen.
4. At the Select A Device screen, select the server from the list of
programmable devices. This may be the only item in the list.
Press Enter.
5. At the Select An Image screen, you will see:
Device to reprogram:
Current ROM revision:
Select Firmware Images:
your server
date of existing ROM version
date of latest ROM version
Press Enter.
6. Review the information on the Caution screen:
Device to reprogram:
Current ROM revision:
Selected ROM revision:
your server
date of existing ROM version
date of ROM version to be installed
Press Enter to reprogram the system ROM or press Esc to discontinue
reprogramming and return to the Select An Image screen.
7. “Reprogramming Firmware” indicates that the system ROM is being
reprogrammed.
IMPORTANT: Do not interrupt this cycle. Interrupting the ROM reprogramming will leave
the firmware in an unknown state. You may not be able to boot the server if this happens.
You will be notified that reprogramming is completed.
8. When ROMPaq is finished reprogramming the system ROM, press Esc
to exit the System ROMPaq utility.
9. Remove the System ROMPaq diskette and reboot the server by cycling
the power (cold boot).
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-3
3-4
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
If you have not yet installed your new 64-Bit/66 MHz Single Channel Wide
Ultra3 SCSI Adapter, you can do so at this time. See Chapter 2 for general
hardware installation and cabling information, then proceed to the next
section, “Installing the Drivers.”
Installing the Drivers
Software drivers must be installed in the server to enable communication
between the processor and the new 64-Bit/66 MHz Single Channel Wide
Ultra3 SCSI Adapter. This installation procedure assumes that you have
already installed your 64-Bit/66-MHz Single Channel Wide Ultra3 SCSI
Adapter and your operating system. The drivers and installation procedures are
unique to the operating system being used. Use the information in this section
to find the location of the driver (or drivers) and necessary installation
information for your operating system. All the drivers and support
documentation can be found on the Compaq SmartStart and Support Software
CD supplied with your new 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI
Adapter.
Windows NT 3.51 or 4.0
Use the following instructions to install the driver on a system already running
Windows NT 3.51 or 4.0. The driver file, named ADPU160M.SYS, is located
on the Compaq SmartStart and Support Software CD supplied with your new
64-Bit/66-MHz Single Channel Wide Ultra3 SCSI Adapter.
1. Start Windows NT 3.51 or 4.0 on the system and log on to an account
with administrative privileges.
2. Insert the Compaq SmartStart and Support Software CD into the CD
drive.
3. Click Start, choose Settings, and click Control Panel.
4. Double-click the SCSI Adapters icon.
5. Choose the Drivers tab and click Add.
6. Click Have Disk and change the drive letter to point to your CD drive.
7. Select the driver file ADPU160M.SYS found in the following directory
root:
\CPQSUPSW\NTSSD\SCSI\160M\ADPU160M.SYS
8. Click OK to add the driver to be installed.
9. Click OK again to copy the driver into your system and exit this setup.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
Installing the Firmware and Software
Windows 2000
Use the following instructions to install the driver on a system already running
Windows 2000. The driver file, named ADPU160M.SYS, is located on the
Compaq SmartStart and Support Software CD supplied with your new
64-Bit/66-MHz Single Channel Wide Ultra3 SCSI Adapter.
1. Start Windows 2000 on the system and log on to an account with
administrative privileges.
2. Insert the Compaq SmartStart and Support Software CD into the CD
drive.
3. Click Start, choose Settings, and click Control Panel.
4. Double-click the System icon.
5. Click the Hardware tab.
6. Click Device Manager to display a list of all the hardware devices
installed, then scroll down to SCSI and RAID Controllers and open the
folder.
You should see the SCSI Controller listed if the SCSI adapter was
properly installed as described in Chapter 2.
7. Double-click the SCSI Controller.
8. Click the Driver tab on the SCSI Controller Properties screen, then click
the Update Driver button.
9. Click Next.
10. Select Display A List Of The Known Drivers For This Device So That I
Can Choose A Specific Driver, then click Next.
11. Click Have Disk and change the drive letter to point to your CD drive.
12. Select the driver file ADPU160M.SYS found in the following directory
root:
\CPQSUPSW\NTSSD\SCSI\160M\ADPU160M.SYS
13. Click OK to add the driver to be installed.
14. Click Next.
You may see an Update Driver Warning screen; click Yes to proceed.
15. The driver you have copied will be listed. Select it and click Next to
install.
16. Click Finish to exit this setup.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-5
3-6
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
SCO UnixWare 7.x
Use the following instructions to install the driver on a system already running
UnixWare 7.xx. The driver file, named ADST70, is located on the UnixWare
7.xx EFS diskette containing HBA drivers.
NOTE: Compaq Extended Feature Supplement (EFS) version 7.xx or later for SCO
UnixWare 7.x is required for operation with the Compaq 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter.
1. Start the system and log in with root privileges.
2. Insert the Compaq SmartStart and Support Software CD into the CD
drive.
3. Select Compaq SCO UnixWare 7.x EFS on the Diskette Builder screen
and create the diskettes for EFS version 7.xx or later.
4. Use the SCO PKGADD utility to install the Compaq EFS from the
diskettes. Online documentation is included on the EFS diskettes. The
driver name is ADST70.
5. Insert the diskette created with EFS drivers labeled HBA into the
diskette drive.
6. At the Unix command line, enter the following command:
pkgadd -d diskette1 –L
A menu will list all drivers on the diskette.
7. Install the driver by entering the driver number associated with file
name ADST70.
8. Remove the diskette, then type q to quit.
9. Reboot your system by typing init 6.
SCO OpenServer 5
To install the driver for the 64-Bit/66-MHz Single Channel Wide Ultra3 SCSI
Adapter on a system already running SCO OpenServer 5, you must first create
a set of Compaq Extended Feature Supplement (EFS) diskettes. These
diskettes are then used to install EFS on the system (after removing older EFS
versions, if necessary).
NOTE: Compaq Extended Feature Supplement (EFS) version 5.36 or later for SCO
OpenServer 5 is required for operation with the Compaq 64-Bit/66 MHz Single Channel
Wide Ultra3 SCSI Adapter.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
Installing the Firmware and Software
Building the EFS Diskettes
EFS diskettes can be built either from the Web or from a Compaq SmartStart
and Support Software CD.
■
To build the diskettes from the Web, download the latest EFS for SCO
OpenServer 5 from the site
www.compaq.com/support/files/server/us/index.html
■
To build the diskettes from the SmartStart and Support Software CD:
1. Insert the Smart Start and Support Software CD (version 4.80 or later)
into the CD drive. This CD launches the application automatically.
2. At the System Utilities screen, click OK.
The Compaq SmartStart Diskette Builder Utility is launched.
3. Expand the Compaq Window and select Compaq SCO OpenServer 5.0
EFS Version 5.36 (or a later version) and continue to the next screen.
4. Chose the option Create Software Diskettes To Floppy Only and follow
the on-screen instructions.
A set of five diskettes will be created.
5. Select Finish when done and then exit from the application.
If your system has an older version of EFS installed, it must be removed
before installing the new EFS version. Follow the instructions in the next
section, Removing an Older Version of EFS.
If your system does not have another version of EFS installed, go directly to
the section Installing the New EFS.
Removing an Older Version of EFS
1. Log in as root.
2. Enter /etc/shutdown -g0 -y to shut down the system.
3. At the Safe to Power Off message, press Enter.
4. When the system reboots, you will see the prompt
Press <Ctrl>+<d> or enter the root password
Enter the root password to begin system maintenance mode.
5. Type /etc/custom and press Enter.
The main custom menu should appear.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-7
3-8
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
6. Press Tab to highlight the software selections, and use the arrow keys to
highlight Compaq Extended Feature Supplement. Press Enter.
7. Press Tab to go back to the menu bar. Choose Software and press
Enter.
8. Choose Remove Software and press Enter.
9. You are prompted to verify the removal of all packages. Choose
Remove and press Enter.
10. When all the EFS packages have been removed, a message will display
that the kernel was relinked. Press Enter to continue.
11. At the message Removal Complete, press Enter to continue.
12. Exit the installation procedure:
a. Choose Host and press Enter.
b. Choose Exit and press Enter.
13. Continue with the step 5 of the procedure described in the next section
to install a new version of EFS.
WARNING: DO NOT reboot the system before installing the new EFS version.
Omit the first four steps of the procedure in the following section.
Installing the New EFS
1. Log in as root.
2. Enter /etc/shutdown -g0 -y to shut down the system.
3. At the Safe to Power Off message, press Enter.
4. When the system reboots, you will see the prompt
Press <Ctrl>+<d> or enter the root password.
Enter the root password to begin system maintenance mode.
5. Type /etc/custom and press Enter.
The main custom menu should appear.
6. Choose Software (on the menu bar) and press Enter.
7. Choose Install New and press Enter.
8. You will be asked what host you want to install from. Select the local
host and press Enter.
NOTE: Only the local host is supported.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
Installing the Firmware and Software
9. Insert diskette Volume 1 of the Compaq EFS for SCO OpenServer
Release 5 into the diskette drive.
10. Choose Continue and press Enter.
The initial EFS screen appears. Each component of the EFS is listed
below the title as it is installed.
11. When prompted, enter the IP address, broadcast address, and network
mask for each installed network controller.
12. When prompted, insert diskette Volume 2 of the Compaq EFS for SCO
OpenServer Release 5 into the drive and press Enter.
13. When installation of the drivers and utilities is complete, the following
message is displayed:
During this installation, the kernel was relinked.
You must reboot your system to make this kernel effective. Press
Return to continue.
14. When the message Installation Complete is displayed, press Return.
EFS should be on the All Software On... list when rebuilding has
finished.
15. Exit the installation procedure:
a. Choose Host and press Enter.
b. Choose Exit and press Enter.
16. At the # prompt, enter reboot.
Novell NetWare 5.1
This section describes how to install the 64-Bit/66-MHz Single Channel Wide
Ultra3 SCSI Adapter driver on a system already running Novell NetWare 5.1.
The driver file, named ADPT160M.HAM, can be found in the following
subdirectory on the SmartStart and Support Software CD:
\CPQSUPSW\NSSD\NWPA
Use the following steps to install the driver ADPT160M.HAM and the file
ADPT160.DDI from the SmartStart and Support Software CD onto a system
running NetWare 5.1.
1. Use the down command to down the server.
2. Power on the system and start NetWare 5.1.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-9
3-10
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
3. Insert the SmartStart and Support Software CD into the CD drive.
4. Copy the following files from the subdirectory
\CPQSUPSW\NSSD\NWPA into your NetWare directory:
ADPT160.HAM
ADPT160.DDI
5. Remove the CD and shutdown the system.
6. Install the Compaq 64-Bit/66-MHz Single Channel Wide Ultra3 SCSI
Adapter.
7. Power on the system and start NetWare 5.1.
NetWare will detect the new adapter and will attempt to load the driver.
8. Follow the screen prompts to load the driver ADPT160.HAM.
9. When presented with a list of drivers, select the driver and press Esc to
load it.
NOTE: Although the Esc option is not shown on this screen, you must use it in order to
load the driver. Pressing Enter will not load the driver.
IBM OS/2
Use the following instructions to install the 64-Bit/66-MHz Single Channel
Wide Ultra3 SCSI Adapter driver on a system already running IBM OS/2. The
driver file, named AICU160.ADD, is located on the SmartStart and Support
Software CD supplied with your new 64-Bit/66-MHz Single Channel Wide
Ultra3 SCSI Adapter.
1. Insert the Smart Start and Support Software CD (version 4.80 or later)
into a system and reboot. This CD launches the application
automatically.
2. At the System Utilities screen, click OK.
3. Choose the option Create Software Diskettes From CD Only and move
to the next screen.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
Installing the Firmware and Software
4. Select Compaq OS/2 Support Software - 4.50A Or Later Version and
move to the next screen.
5. Chose the option Create Software Diskettes To Floppy Only, then click
through the following screens until a screen indicating Please Insert
Diskette 4 Of 5… is displayed.
6. Insert a formatted 1.44 MB diskette into the diskette drive and click OK.
The drivers related to the 64-Bit/66-MHz Single Channel Wide Ultra3
SCSI Adapter Controller will be copied onto the diskette.
7. Click Finish when done.
8. Exit from the application.
9. Insert the floppy diskette 4 into the floppy drive.
10. At the command prompt, type ddinstal.
11. Select A:\ADD as the source directory and select Install.
12. Select Compaq Adaptec SCSI Driver for OS/2 and proceed. This will
install the selected driver.
13. After the driver installation has finished, reboot the system.
14. Reboot the system again to load the AICU160.ADD driver.
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: d-ch3 Installing Firmware and Software.doc Last Saved On: 7/21/00 2:23 PM
3-11
Appendix
A
Regulatory Compliance Notices
Federal Communications Commission
Notice
Part 15 of the Federal Communications Commission (FCC) Rules and
Regulations has established Radio Frequency (RF) emission limits to provide
an interference-free radio frequency spectrum. Many electronic devices,
including computers, generate RF energy incidental to their intended function
and are, therefore, covered by these rules. These rules place computers and
related peripheral devices into two classes, A and B, depending upon their
intended installation. Class A devices are those that may reasonably be
expected to be installed in a business or commercial environment. Class B
devices are those that may reasonably be expected to be installed in a
residential environment (that is, personal computers). The FCC requires
devices in both classes to bear a label indicating the interference potential of
the device as well as additional operating instructions for the user.
The rating label on the device shows which class (A or B) the equipment falls
into. Class B devices have an FCC logo or FCC ID on the label. Class A
devices do not have an FCC logo or ID on the label. Once the class of the
device is determined, refer to the following corresponding statement.
Compaq Confidential – Need to Know Required
Writer: JTurner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: e-appa Regulatory Compliance Notices.doc Last Saved On: 7/21/00 1:10 PM
A-2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Class A Equipment
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to
correct the interference at personal expense.
Class B Equipment
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
■
Reorient or relocate the receiving antenna.
■
Increase the separation between the equipment and receiver.
■
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
■
Consult the dealer or an experienced radio or television technician for
help.
Compaq Confidential – Need to Know Required
Writer: JTurner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: e-appa Regulatory Compliance Notices.doc Last Saved On: 7/21/00 1:10 PM
Regulatory Compliance Notices
Declaration of Conformity for Products Marked
with FCC Logo, United States Only
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. For questions
regarding this declaration, contact:
Compaq Computer Corporation
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
Or call (281) 514-3333
To identify this product, refer to the Series number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications
made to this device that are not expressly approved by Compaq Computer
Corporation may void the user's authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic
RFI/EMI connector hoods in order to maintain compliance with FCC Rules
and Regulations.
Compaq Confidential – Need to Know Required
Writer: JTurner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: e-appa Regulatory Compliance Notices.doc Last Saved On: 7/21/00 1:10 PM
A-3
A-4
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Canadian Notice (Avis Canadien)
Class A Equipment
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
Class B Equipment
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
European Union Notice
Products with the CE Marking comply with both the EMC Directive
(89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the
Commission of the European Community.
Compliance with these directives implies conformity to the following
European Norms (in brackets are the equivalent international standards):
■
EN55022 (CISPR 22) - Electromagnetic Interference
■
EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic
Immunity
■
EN60950 (IEC950) - Product Safety
Compaq Confidential – Need to Know Required
Writer: JTurner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: e-appa Regulatory Compliance Notices.doc Last Saved On: 7/21/00 1:10 PM
Regulatory Compliance Notices
Japanese Notice
Taiwanese Notice
Compaq Confidential – Need to Know Required
Writer: JTurner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: e-appa Regulatory Compliance Notices.doc Last Saved On: 7/21/00 1:10 PM
A-5
Appendix
B
Electrostatic Discharge
To prevent damaging the system, be aware of the precautions you need to
follow when setting up the system or handling parts. A discharge of static
electricity from a finger or other conductor may damage system boards or
other static-sensitive devices. This type of damage may reduce the life
expectancy of the device.
To prevent electrostatic damage, observe the following precautions:
■
Avoid hand contact by transporting and storing products in static-safe
containers.
■
Keep electrostatic-sensitive parts in their containers until they arrive at
static-free workstations.
■
Place parts on a grounded surface before removing them from their
containers.
■
Avoid touching pins, leads, or circuitry.
■
Make sure you are properly grounded when touching a static-sensitive
component or assembly.
Compaq Confidential – Need to Know Required
Writer: Valerie M. Yeary Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: f-appb Electrostatic Discharge.doc Last Saved On: 7/21/00 1:11 PM
B-2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
Grounding Methods
There are several methods for grounding. Use one or more of the following
methods when handling or installing electrostatic-sensitive parts:
■
Use a wrist strap connected by a ground cord to a grounded workstation
or computer chassis. Wrist straps are flexible straps with a minimum of
1 megohm ± 10 percent resistance in the ground cords. To provide
proper ground, wear the strap snug against the skin.
■
Use heel straps, toe straps, or boot straps at standing workstations.
Wear the straps on both feet when standing on conductive floors or
dissipating floor mats.
■
Use conductive field service tools.
■
Use a portable field service kit with a folding static-dissipating work
mat.
If you do not have any of the suggested equipment for proper grounding, have
an Authorized Compaq Reseller install the part.
IMPORTANT: For more information on static electricity, or assistance with product
installation, contact your Authorized Compaq Reseller.
Compaq Confidential – Need to Know Required
Writer: Valerie M. Yeary Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: f-appb Electrostatic Discharge.doc Last Saved On: 7/21/00 1:11 PM
Index
A
adding a separate SCSI bus 2-5
adding internal SCSI devices 2-6
attaching cables 2-4
B
building diskettes
EFS for OpenServer 5 3-6
EFS for UnixWare 7 3-6
C
cables
attaching 2-4
characteristics 1-6
identifying 1-6
option kit part numbers 1-5
ordering 1-5
terminating 1-4
cabling
connectors 2-3
external connections 2-3
internal connections 2-4
Single Channel Wide Ultra3
SCSI Adapter 2-3
illustrated 2-4
cautions
electrostatic discharge 2-2
grounding 2-2
terminating SCSI cables 1-5,
2-5
Compaq authorized reseller ix
Compaq System Configuration
Utility 2-7
Compaq website ix
completing installation 2-7
compliance 1-2
connecting additional internal SCSI
devices 2-6
connectors
cabling 2-3
external 1-2, 1-6
internal 1-1, 1-6
SCSI cable 1-6
standard Wide SCSI 1-6
creating diskettes
EFS for OpenServer 5 3-6
EFS for UnixWare 7 3-6
ROMPaq 3-2
UnixWare 7.x drivers 3-6
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: g-index.doc Last Saved On: 7/21/00 1:40 PM
2
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
D
H
data transfer rates 1-1
defined
Single Channel Wide Ultra3
SCSI Adapter 1-1
diskettes
EFS, for OpenServer 5 3-6
EFS, for UnixWare 7 3-6
diskettes, creating
ROMPaq 3-2
UnixWare 7.x drivers 3-6
driver installation
UnixWare 7.x 3-6
drivers
installing 3-4
help
E
EFS
removing older 3-7
EFS diskettes
creating, for OpenServer 5 3-6
creating, for UnixWare 7 3-6
external connectors 1-2, 1-6
F
features 1-1
figures
external SCSI cabling on a
Compaq server 2-4
firmware, updating 2-7, 3-1
additional sources viii
Compaq website ix
Compq authorized resellers,
telephone numbers ix
technical support telephone
numbers viii
http://www.compaq.com ix
I
IBM OS/2 drivers 3-10
icons
symbols on equipment vii
illustrated
external SCSI cabling on a
Compaq server 2-4
installing
drivers 2-7, 3-4
UnixWare 7.x 3-6
multiple adapters 1-4
Single Channel Wide Ultra3
SCSI Adapter
items needed 2-1
steps 2-3
internal connectors 1-1, 1-6
J
Japanese notice A-5
L
G
getting help viii
grounding methods B-2
low voltage differential
devices See LVD devices
LVD devices 1-3
M
Microsoft Windows 2000
drivers 3-5
Microsoft Windows NT
drivers 3-4
multiple adapters, installing 1-4
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: g-index.doc Last Saved On: 7/21/00 1:40 PM
Index
N
S
NetWare 5.1 drivers 3-9
SCO OpenServer 5 drivers 3-6
SCO UnixWare 7.x drivers 3-6
SCSI bus
adding 2-5
separate 2-5
SCSI cabling guidelines
cabling SCSI devices 2-3
connecting SCSI cables 1-3
port assignments 2-5
SCSI devices
cables See cables
connectors 1-3
Fast-SCSI-2 1-1, 1-2
Fast-Wide SCSI-2 1-1, 1-2
supported 1-1
tagged command queuing 1-2
terminating 1-4
SCSI IDs
adapter 1-4
bus priority 1-4
peripherals 1-4
SE devices 1-3
separate SCSI bus 2-5
servers
opening 2-2
preparing 2-2
Single Channel Wide Ultra3 SCSI
Adapter
cabling 2-3
compliance 1-2
data transfer rates 1-1
defined 1-1
features 1-1
installing 2-1
single-ended devices See SE
devices
standard Wide SCSI
connectors 1-6
storage, external 1-2
symbols in text vii
symbols on equipment vii
System ROMPaq
creating diskettes 3-2
running 3-3
O
opening the server 2-2
OpenServer 5 drivers 3-6
operating system drivers 3-4
operating systems
UnixWare 7.x 3-6
ordering cables 1-5
OS/2 drivers 3-10
P
PCI 1-2
PCI bus master 1-2
PCI local bus 1-2
preparing the server 2-2
R
rates, data transfer 1-1
regulatory compliance
Canadian notice A-4
European Union notice A-4
Federal Communications
Commission notice A-1
removing older EFS 3-7
replacing the adapter 2-6
RJ-45 receptacle vii
ROM
reprogramming 3-3
upgrading 3-2
ROMPaq
creating diskettes 3-2
running 3-3
running System ROMPaq 3-3
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: g-index.doc Last Saved On: 7/21/00 1:40 PM
3
4
Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide
T
U
tagged command queuing 1-2
Taiwanese notice A-5
technical support viii
telephone numbers ix
terminating, SCSI devices 1-4
text conventions vi
UnixWare 7.x drivers 3-6
updating
firmware 2-7
system ROM 2-7
W
warnings
electrical shock viii
installation instructions 2-1
Windows 2000 drivers 3-5
Windows NT drivers 3-4
www.compaq.com. viii
Compaq Confidential – Need to Know Required
Writer: John Turner Project: Compaq 64-Bit/66 MHz Single Channel Wide Ultra3 SCSI Adapter Installation Guide Comments:
Part Number: 154060-002 File Name: g-index.doc Last Saved On: 7/21/00 1:40 PM