CSLUX-300
Multi-Format to HDMI Scaler
Operation Manual
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. Cypress Technology assumes no
responsibility for any infringements of patents or other rights of third
parties which may result from its use.
Cypress Technology assumes no responsibility for any inaccuracies
that may be contained in this document. Cypress also makes no
commitment to update or to keep current the information contained
in this document.
Cypress Technology reserves the right to make improvements to this
document and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means—
electronic, mechanical, magnetic, optical, chemical, manual, or
otherwise—without express written permission and consent from
Cypress Technology.
© Copyright 2011 by Cypress Technology.
All Rights Reserved.
Version 1.1 August 2011
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may be
trademarks of the companies with which they are associated.
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
•
To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
•
Never spill liquid of any kind on or into this product.
•
Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
•
Do not attach the power supply cabling to building surfaces.
•
Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
•
Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
•
To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO.
DATE DD/MM/YY SUMMARY OF CHANGE
RDV1
02/04/14
Preliminary Release
CONTENTS
1. Introduction�������������������������������������������� 1
2. Applications������������������������������������������� 1
3. Package Contents�������������������������������� 1
4. System Requirements���������������������������� 1
5. Features�������������������������������������������������� 2
6. Operation Controls and Functions������� 3
6.1 Front Panel�����������������������������������������3
6.2 Rear Panel�����������������������������������������4
6.3 Remote Control���������������������������������6
6.4 RS-232 Pin Assignment����������������������7
6.5 RS-232 Commands���������������������������8
6.6 OSD Menu����������������������������������������10
6.7 Input Resolution Support����������������14
6.8 Output Resolution Support�������������15
7. Connection Diagram�������������������������� 16
8. Specifications�������������������������������������� 17
9. Acronyms��������������������������������������������� 18
1. INTRODUCTION
​​
This
Multi-Format to HDMI Scaler is an advanced HDMI, PC, Composite,
S-Video and Component switcher/scaler. This device can scale and
switch input sources and display them to its HDMI and VGA/HD
outputs simultaneously, with their associated audio signals, at a wide
range of output resolutions (up to 1080p or WUXGA(RB)). Control is via
IR remote, or via front panel buttons and includes an on-screen menu
providing settings and system information.
2. APPLICATIONS
• Digital and analog signal convergence
• Convert analog video/audio signals for use with digital displays
• Integrate multiple sources and signal types to a single display in a
meeting room or conference hall environment
3. PACKAGE CONTENTS
• Multi-Format to HDMI Scaler
• Remote Control (CR-143)
• 5 V/3 A DC Power Adaptor
• D-sub 15-pin to 3 RCA Adaptor Cable
• Operation Manual
4. SYSTEM REQUIREMENTS
Source equipment such as Blu-ray/DVD players, VGA or HDMI display
and amplifier/active speakers with connection cables.
1
5. FEATURES
• Supports HDMI, Composite Video, S-Video, and PC (VGA)/HD
(Component) inputs
• Supports HDMI and VGA/Component (with adaptor) outputs
• Supports analog stereo, optical and coaxial digital inputs and
optical digital output, analog stereo output or embedding to HDMI
output
• Supports conversion of multiple video formats and audio input to
HDMI or PC/HD and analog stereo outputs
• Supports EDID and HDCP
• Supports 3D de-interlacing, noise reduction and 3D comb filter
• Supports frame rate conversion
• Supports RS-232, remote handset, and front panel control
2
6. OPERATION CONTROLS AND FUNCTIONS
6.1 Front Panel
CSLUX-300 DIGITAL VIDEO SCALER
XGA
POWER
IR
INPUT
CV
SV
PC
COMP
HDMI 1
HDMI 2
MENU
-
+
ENTER
720P
1
2
3
4
5
6
1 POWER and LED
Press this button to switch the device ON or to put the device
into STANDBY mode. When the device is connected to an active
power supply, the LED will illuminate and the device will switch ON
automatically.
2 IR Window
Receives only the IR signal from the supplied remote control.
3 INPUT Button and LEDs
Press to repeatedly select the required input. An LED will illuminate
to indicate the currently selected source.
4 MENU
Press this button to enter into the on-screen menu (OSD).
5 −/+ (Minus/Plus)
Use these buttons to navigate down and up in the on-screen
menu.
6 ENTER
Press this button to confirm the selection.
Note: Pressing '−' (MINUS) and ENTER simultaneously will
immediately switch the output resolution of the device to 720p60.
Pressing '+' (PLUS) and ENTER simultaneously will immediately switch
the output resolution of the device to XGA.
3
6.2 Rear Panel
2
OUTPUT
OPTICAL
L/R
3
5
RS232
SERVICE
R
L/R
PC/HD
HDMI
INPUT
OPTICAL
L
CV
R
L
DC 5V
PC
HDMI 1
HDMI 2
Cr/Pr
1
Cb/Pb
Y
SV
R
L
4
1 OUTPUTS
HDMI: Connect to an HDMI display or amplifier for video and/or
audio output.
PC/HD: Connect to a monitor/display for video output. For HD
(Component) output, use the supplied D-sub 15-pin to 3 RCA
adaptor cable for HD resolutions from 480p~1080p.
OPTICAL: Connect to an amplifier or active speakers for audio
output in digital format.
L/R: Connect to an amplifier or active speakers for audio output in
stereo format.
2 RS-232
Connect to a PC/Laptop to use RS-232 commands to control the
device (See Section 6.5 for details on RS-232 commands).
3 SERVICE
4
Reserved for manufacturer use only.
4 INPUTS
HDMI 1: Connect to an HDMI source such as Blu-ray/DVD player for
both video and audio signal conversion.
HDMI 2: Connect to an HDMI source such as Blu-ray/DVD player
for both video and audio signal conversion.
PC: Connect to a PC/Laptop source for video signal input with a
D-sub 15-pin cable.
YCbCr/YPbPr and L/R: Connect to source equipment such as a
DVD player for both video and audio signal conversion.
SV and L/R: Connect to an S-Video source such as a video/DVD
player for both video and audio signal conversion.
CV and L/R: Connect to a composite video source such as video/
DVD player for both video and audio signal conversion.
OPTICAL: Connect to a source's optical output for audio signal
conversion.
L/R: Connect to source's L/R output with 3.5mm Mini-jack for audio
signal conversion.
5 DC 5V
Plug the 5 V DC power supply into the unit and connect the
adaptor to an AC outlet.
5
6.3 Remote Control
1 POWER
Press this button to switch the device ON
or to put the device into STANDBY mode.
2
3
INPUT
POWER
CV
SV
COMP
PC
HDMI 1
HDMI 2
1
2 INPUT
Press to repeatedly select the required
input. An LED will illuminate to indicate
the currently selected source.
3 CV/SV/COMP/PC/HDMI 1/HDMI 2
Press to directly select the required input.
4
EXIT
MENU
6
AUTO
ADJUST
RESET
7
8
4 EXIT
5
OK
Press this button to exit the menu or the
current selection in the on-screen menu.
5 MENU
Press this button to enter the on-screen
menu.
CR-143
6 RESET
Press this button to return the device to the factory default settings.
7 AUTO ADJUST
Press the button to optimize the positioning of the picture (picture
centering) on the screen.
8 ▲▼◄► and OK
6
Press OK to confirm the selection or use the directional buttons to
navigate the on-screen menus.
6.4 RS-232 Pin Assignment
MULTI-FORMAT TO
HDMI SCALER
REMOTE CONTROL
PIN
Assignment
PIN
Assignment
1
NC
1
NC
2
Tx
2
Rx
3
Rx
3
Tx
4
NC
4
NC
5
GND
5
GND
6
NC
6
NC
7
NC
7
NC
8
NC
8
NC
9
NC
9
NC
►
◄
Baud Rate: 9600bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
7
6.5 RS-232 Commands
COMMAND
DESCRIPTION
S SOURCE 1~6
1=HDMI1
2=HDMI2
3=YPbPr
R SOURCE
Reports the numerical equivalent for
SOURCE setting (as above)
S OUTPUT 0~25
0=Native
1=640×480
2=800×600
3=1024×768
4=1280×768
5=1360×768
6=1280×720
7=1280×800
8=1280×1024
9=1440×900
10=1400×1050
11=1680×1050
R OUTPUT
Reports the numerical equivalent for OUTPUT
setting (as above)
S SIZE 0~6
0=OVERSCAN
1=FULL
2=BEST FIT
3=PAN SCAN
R SIZE
Reports the numerical equivalent for SIZE
setting (as above)
S CONTRAST 0~60
Setups the numerical equivalent for
CONTRAST setting (as left)
R CONTRAST
Reports the numerical equivalent for
CONTRAST setting
S BRIGHTNESS 0~60
Setups the numerical equivalent for
BRIGHTNESS setting (as left)
R BRIGHTNESS
Reports the numerical equivalent for
BRIGHTNESS setting
8
4=VIDEO
5=S-VIDEO
6=PC
12=1600×1200
13=1920×1080
16=1920×1200
17=480p
18=720p@60
19=1080p@60
20=1080i@60
22=576p
23=720p@50
24=1080p@50
25=1080i@50
4=LETTER BOX
5=UNDER 2
6=UNDER 1
COMMAND
DESCRIPTION
S HUE 0~60
Setups the numerical equivalent for HUE
setting (as left)
R HUE
Reports the numerical equivalent for HUE
setting
S SATURATION 0~60
Setups the numerical equivalent for
SATURATION setting (as left)
R SATURATION
Reports the numerical equivalent for
SATURATION setting
S SHARPNESS 0~30
Setups the numerical equivalent for
SHARPNESS setting (as left)
R SHARPNESS
Reports the numerical equivalent for
SHARPNESS setting
S NR 0~3
0=OFF
1=LOW
R NR
Reports the numerical equivalent for the
NOISE REDUCTION setting (as above)
S AUDIO DELAY 0~3
0=OFF
1=40ms
R AUDIO DELAY
Reports the numeric equivalent for AUDIO
DELAY setting (as above)
S AUDIO MUTE 0/1
0=ON
R AUDIO MUTE
Reports the numeric equivalent for AUDIO
MUTE setting (as above)
S KEY LOCK 0/1
0=ENABLE
R KEY LOCK
Reports the numeric equivalent for KEY
LOCK setting (as above)
FW
Checks the FIRMWARE version
S RESET 1
Setups the numerical equivalent for RESET
setting (as left)
S POWER 0/1
0=OFF
R POWER
Reports the numeric equivalent for POWER
setting (as above)
2=MIDDLE
3=HIGH
2=110ms
3=150ms
1=MUTE
1=DISABLE
1=ON
Note:
1. Audio Delay is only supported on Analog Stereo output.
2. When the HDMI input is encoded with HDCP, no image will be
output from the PC/HD output.
9
3. Only LPCM 2 channel digital audio is supported, please ensure
that the source audio is set to LPCM 2 channel audio in order to
avoid unnecessary audio noise.
4. RS-232 commands will be not executed unless followed with a
carriage return and LF. Commands are case-insensitive.
6.6 OSD Menu
MAIN MENU
SUBMENU
3RD MENU
DISPLAY
OUTPUT
640×480 60
800×600 60
1024×768 60
1280×768 60
1360×768 60
1280×720 60
1280×800 60
1280×1024 60
1440×900 60
1400×1050 60
1680×1050 60
1600×1200 60
1920×1080 60
1920×1200 60
720×480P 60
1280×720P 60*
1920×1080I 60
1920×1080P 60
720×576P 50
1280×720P 50
1920×1080I 50
1920×1080P 50
10
4TH MENU
MAIN MENU
SUBMENU
3RD MENU
DISPLAY
SIZE
OVER SCAN
(For VIDEO input)
FULL*
4TH MENU
BEST FIT
PAN SCAN
LETTER BOX
UNDER 2
UNDER 1
MODE INFO
OFF
INFO*
ON
PC
AUTO SETUP
(For PC input)
H_POSITION
V_POSITION
PHASE
CLOCK
WXGA/XGA
XGA*
WXGA
RESET
11
MAIN MENU
SUBMENU
3RD MENU
COLOR
COLOR
R
G
B
R OFFSET
G OFFSET
B OFFSET
CONTRAST
0~60
BRIGHTNESS
0~60
HUE
0~60
SATURATION
0~60
SHARPNESS
0~30
NR
OFF*
LOW
MIDDLE
HIGH
AUDIO
VOLUME
0~100
DELAY
OFF*
40 ms
110 ms
150 ms
SOUND
ON*
MUTE
AUDIO SELECT
ANALOG*
(For AV/SV/YPbPr/
S/PDIF
VGA input)
12
4TH MENU
MAIN MENU
SUBMENU
SETUP
FACTORY RESET
KEY LOCK
3RD MENU
4TH MENU
OFF*
ON
POWER SAVE
OFF*
ON
INFORMATION
INPUT
OUTPUT
REVISION
Note: Items with Asterisk (*) are the Factory default settings.
13
6.7 Input Resolution Support
INPUT RESOLUTION
CV/SV
COMP
PC
HDMI
NTSC/PAL

-
-
-
480i/576i
-

-

480p/576p
-

-

720p@50/60 Hz
-

-

1080i@50/60 Hz
-

-

1080p@50/60 Hz
-

-

VGA@60/72/75 Hz
-
-


SVGA@56/60/72/75 Hz
-
-


XGA@60/70/75 Hz
-
-


SXGA@60/75 Hz
-
-


UXGA@60 Hz
-
-


1280×800@60 Hz
-
-


1680×1050RB@60 Hz
-
-


1920×1080@60 Hz
-
-


14
6.8 Output Resolution Support
OUTPUT RESOLUTION
PC/HD
HDMI
480p/576p
HD

720p@50/60 Hz
HD

1080i@50/60 Hz
HD

1080p@50/60 Hz
HD

VGA@60 Hz


SVGA@60 Hz


XGA@60 Hz


SXGA@60 Hz


UXGA@60 Hz


1280×768@60 Hz


1280×800@60 Hz


1360×768@60 Hz


1400×1050@60 Hz


1440×900@60 Hz


1680×1050@60 Hz


1920×1200@60 Hz


15
7. CONNECTION DIAGRAM
HD Satellite Receiver
HDMI, Optical Digital and
Analog Audio Inputs
Blu-ray/DVD Player
PC or RS-232
Control System
HDMI, Composite Video and
Analog Audio Inputs
RS-232
OUTPUT
L/R
OPTICAL
Set-top Box
RS232
SERVICE 1
R
L/R
L
CV
R
L
DC 5V
PC
HDMI 1
Power
Supply
INPUT
OPTICAL
SERVICE 2
PC/HD
HDMI
HDMI 2
Cr/Pr
Cb/Pb
Y
SV
R
L
PC
S-Video and
Analog Audio Inputs
VGA and Analog Audio Inputs
Analog
Audio
Output
Optical
Digital
Output
AV Receiver
16
HDMI
Output
TV or Monitor
OR
VGA
Output
Component
Output
TV or Monitor with
3.5mm audio input
8. SPECIFICATIONS
Input Ports
2×HDMI, 1×VGA,
1×Composite Video,
1×S-Video, 1×Component Video,
3×Analog Stereo (L/R),
1×Optical,
1×3.5mm Mini-jack,
1×RS-232,
1×USB (Service Only),
1×3.5mm Mini-jack (Service Only)
Output Ports
1×HDMI,
1×VGA,
1×Optical,
1×3.5mm
Mini-jack
Input Resolutions Support
Up to 1080p & UXGA
Output Resolutions
Up to 1080p & WUXGA (RB)
Support
Power Supply
5 V/3 A DC (US/EU standards, CE/FCC/UL
certified)
Dimensions
320 mm (W)×182 mm (D)×44 mm (H)
Weight
1,600 g
Chassis Material
Metal
Color
Black
Operating Temperature
0 ˚C~40 ˚C/32 ˚F~104 ˚F
Storage Temperature
−20 ˚C~60 ˚C/−4 ˚F~140 ˚F
Relative Humidity
20~90 % RH (non-condensing)
Power Consumption
10.5 W
17
9. ACRONYMS
ACRONYM
COMPLETE TERM
COMP
Component Video
CV
Composite Video
DVI
Digital Visual Interface
EDID
Extended Display Identification Data
HDCP
High-Bandwidth Digital Content Protection
HDMI
High-Definition Multimedia Interface
IR
Infrared
NR
Noise Reduction
NTSC
National Television System Committee
OSD
On-screen Display (Menu)
PAL
Phase Alternating Line
RGB
Red Green Blue
SV
S-Video
USB
Universal Serial Bus
UXGA
Ultra Extended Graphics Array
VGA
Video Graphics Array
XGA
Extended Graphics Array
WUXGA
Wide Ultra Extended Graphics Array
18
CYPRESS TECHNOLOGY CO., LTD
Home page: http://www.cypress.com.tw
20130625 MPM-CSLUX300I