Electrolux CM 600 BLK Service manual

ELECTROLUX SERVICE MANUAL
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
* REVISION 1
S54M238V169DE
MODELS
OVER THE RANGE
MICROWAVE OVENS
PLMV169DC
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
* Serial # 44513937 ~ and above
* Serial # 44513257 ~ and above
* Serial # 44812717 ~ and above
* Serial # 44514859 ~ and above
In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should
be used.
WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage and
current. Contact with the following parts may result in a severe, possibly fatal, electrical shock. (High Voltage
Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..)
TABLE OF CONTENTS
Page
PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE EXPOSURE TO EXCESSIVE MICROWAVE ENERGY .................. INSIDE FRONT COVER
BEFORE SERVICING ..................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL .............................................................................................................. 1
MICROWAVE MEASUREMENT PROCEDURE .................................................................................................. 2
FOREWORD AND WARNING ................................................................................................................................3
PRODUCT SPECIFICATIONS ...............................................................................................................................4
GENERAL INFORMATION ...................................................................................................................................4
OPERATION .........................................................................................................................................................7
TROUBLESHOOTING GUIDE ............................................................................................................................. 12
TEST PROCEDURE ............................................................................................................................................ 14
TOUCH CONTROL PANEL ASSEMBLY ............................................................................................................. 26
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE .................................................................. 32
PICTORIAL DIAGRAM ........................................................................................................................................ 40
POWER UNIT CIRCUIT ....................................................................................................................................... 41
LSI UNIT CIRCUIT ............................................................................................................................................... 42
PRINTED WIRING BOARD ................................................................................................................................. 43
PARTS LIST .............................................................................................................................(revised)... .44
PACKING AND ACCESSORIES...................................................................................................................48
*NOTE:
Units with serial number range above, employ new Chassis supports. This manual is for units using these
components as stated.
This document has been published to be used for after sales service only. The contents are subject to change without notice.
ELECTROLUX HOME PRODUCTS, INC.
P. O. Box 212378, Augusta, GA, 30917
800•944•9044
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE
ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs as necessary: (1) interlock operation, (2) proper door closing, (3)
seal and sealing surfaces (arcing, wear, and other damage), (4) damage to or loosening of hinges and
latches, (5) evidence of dropping or abuse.
(c) Before turning on microwave power for any service test or inspection within the microwave generating
compartments, check the magnetron, wave guide or transmission line, and cavity for proper alignment,
integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal, and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
(e) A microwave leakage check to verify compliance with the Federal Performance Standard should be
performed on each oven prior to release to the owner.
(RD2110U)
BEFORE SERVICING
Before servicing an operative unit, perform a microwave emission check as per the Microwave
Measurement Procedure outlined in this service manual.
If microwave emissions level is in excess of the specified limit, contact ELECTROLUX HOME
PRODUCTS, INC. immediately.
If the unit operates with the door open, service person should 1) tell the user not to operate the oven
and 2) contact ELECTROLUX HOME PRODUCTS, INC. and Food and Drug Administration's
Center for Devices and Radiological Health immediately.
Service personnel should inform ELECTROLUX HOME PRODUCTS, INC. of any certified unit
found with emissions in excess of 4mW/cm2. The owner of the unit should be instructed not to use
the unit until the oven has been brought into compliance.
(RD8100U)
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
WARNING TO SERVICE PERSONNEL
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with
following parts may result in a severe, possibly
fatal, electrical shock.
(Example)
High Voltage Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
Read the Service Manual carefully and follow all
instructions.
Don't Touch !
Danger High Voltage
When the testing is completed,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power
transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is
installed.
7. Run the oven and check all functions.
Before Servicing
1. Disconnect the power supply cord
remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
, and then
WARNING:RISK OF ELECTRIC SHOCK.
DISCHARGE THE HIGH-VOLTAGE
CAPACITOR BEFORE SERVICING.
The high-voltage capacitor remains charged about 60
seconds after the oven has been switched off. Wait for 60
seconds and then short-circuit the connection of the highvoltage capacitor (that is the connecting lead of the highvoltage rectifier) against the chassis with the use of an
insulated screwdriver.
After repairing
1. Reconnect all leads removed from components during
testing.
2. Reinstall the outer case (cabinet).
3. Reconnect the power supply cord after the outer case is
installed.
4. Run the oven and check all functions.
Whenever troubleshooting is performed the power supply
must be disconnected. It may in, some cases, be necessary
to connect the power supply after the outer case has been
removed, in this event,
1. Disconnect the power supply cord, and then remove
outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power
transformer.
5. Ensure that these leads remain isolated from other
components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
Microwave ovens should not be run empty. To test for the
presence of microwave energy within a cavity, place a cup
of cold water on the oven turntable, close the door and set
the power to HIGH and set the microwave timer for two (2)
minutes. When the two minutes has elapsed (timer at zero)
carefully check that the water is now hot. If the water
remains cold carry out Before Servicing procedure and reexamine the connections to the component being tested.
When all service work is completed and the oven is fully
assembled, the microwave power output should be checked
and microwave leakage test should be carried out.
1
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
MICROWAVE MEASUREMENT PROCEDURE
A. Requirements:
1) Microwave leakage limit (Power density limit): The power density of microwave radiation emitted by a microwave oven
should not exceed 1mW/cm2 at any point 5cm or more from the external surface of the oven, measured prior to acquisition
by a purchaser, and thereafter (through the useful life of the oven), 5 mW/cm2 at any point 5cm or more from the external
surface of the oven.
2) Safety interlock switches:
Primary interlock relay switch shall prevent microwave radiation emission in excess of the requirement as above
mentioned. Secondary interlock relay and door sensing switch shall prevent microwave radiation emission in excess of
5 mW/cm2 at any point 5cm or more from the external surface of the oven.
B. Preparation for testing:
Before beginning the actual measurement of leakage, proceed as follows:
1) Make sure that the actual instrument is operating normally as specified in its instruction booklet.
Important:
Survey instruments that comply with the requirement for instrumentation as prescribed by the performance standard for
microwave ovens, 21 CFR 1030.10(c)(3)(i), must be used for testing.
2) Place the oven tray in the oven cavity.
3) Place the load of 275±15 ml (9.8 oz) of tap water initially at 20±5O C (68OF) in the center of the oven cavity.
The water container shall be a low form of 600 ml (20 oz) beaker with an inside diameter of approx. 8.5 cm (3-1/2 in.) and
made of an electrically nonconductive material such as glass or plastic.
The placing of this standard load in the oven is important not only to protect the oven, but also to insure that any leakage
is measured accurately.
4) Set the cooking control on Full Power Cooking Mode.
5) Close the door and select a cook cycle of several minutes. If the water begins to boil before the survey is completed, replace
it with 275 ml of cool water.
C. Leakage test:
Closed-door leakage test (microwave measurement):
1) Grasp the probe of the survey instrument and hold it perpendicular to the gap between the door and the body of the oven.
2) Move the probe slowly, not faster than 1 in./sec. (2.5 cm/sec.) along the gap, watching for the maximum indication on the
meter.
3) Check for leakage at the door screen, sheet metal seams and other accessible positions where the continuity of the metal
has been breached (eg., around the switches, indicator, and vents).
While testing for leakage around the door, pull the door away from the front of the oven as far as is permitted by the closed
latch assembly.
4) Measure carefully at the point of highest leakage and make sure that the highest leakage is no greater than 4mW/cm2, and
that the primary interlock switch/secondary interlock relay does turn the oven OFF before any door movement.
NOTE: After servicing, record data on service invoice and microwave leakage report.
2
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
SERVICE MANUAL
ELECTROLUX
PRODUCT DESCRIPTION
OVER THE RANGE
MICROWAVE OVEN
GENERAL INFORMATION
GLMV169DB / GLMV169DQ
GLMV169DS / PLMV169DC
FOREWORD
OPERATION
This Manual has been prepared to provide Electrolux Home Products
Service Personnel with Operation and Service Information for the
ELECTROLUX OVER THE RANGE MICROWAVE OVENS,
GLMV169DB, GLMV169DQ, GLMV169DS, PLMV169DC.
It is recommended that service personnel carefully study the entire text
of this manual so that they will be qualified to render satisfactory
customer service.
Check the interlock switches and the door seal carefully. Special
attention should be given to avoid electrical shock and microwave
radiation hazard.
WARNING
Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is not any other visible damage with the oven.
Servicing and repair work must be carried out only by trained service
personnel.
DANGER
Certain initial parts are intentionally not grounded and
present a risk of electrical shock only during servicing.
Service personnel - Do not contact the following parts while
the appliance is energized;
High Voltage Capacitor, Power Transformer, Magnetron,
High Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.
All the parts marked “*” on parts list are used at voltages more
than 250V.
Removal of the outer wrap gives access to voltage above 250V.
All the parts marked “ ∆” on parts list may cause undue microwave
exposure, by themselves, or when they are damaged, loosened
or removed.
ELECTROLUX HOME PRODUCTS, INC.
3
TROUBLESHOOTING GUIDE AND
TEST PROCEDURE
TOUCH CONTROL PANEL
COMPONENT REPLACEMENT
AND ADJUSTMENT PROCEDURE
WIRING DIAGRAM
PARTS LIST
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
PRODUCT SPECIFICATION
ITEM
DESCRIPTION
Power Requirements
120 Volts / 13.3 Amperes
60 Hertz
Single phase, 3 wire grounded
Power Output
1000 watts (IEC-705 TEST PROCEDURE)
Operating frequency of 2450MHz
Case Dimensions
Width 29-15/16"
Height 16-3/8"
Depth 15- 1/16" (Not including the door handle)
Cooking Cavity Dimensions
1.6 Cubic Feet
Width 21"
Height 8-7/8"
Depth 14-7/16"
Hood lamp
2 bulbs, 20W x 2, Incandescent light bulbs
Hood fan
Approx. 300 C.F.M.
Control Complement
Touch Control System
Clock ( 1:00 - 12:59 )
Timer (0 - 99 min. 99 seconds)
Microwave Power for Variable Cooking
Repetition Rate;
P-HI .................................................. Full power throughout the cooking time
P-90 .................................................................... approx. 90% of Full Power
P-80 .................................................................... approx. 80% of Full Power
P-70 .................................................................... approx. 70% of Full Power
P-60 .................................................................... approx. 60% of Full Power
P-50 .................................................................... approx. 50% of Full Power
P-40 .................................................................... approx. 40% of Full Power
P-30 .................................................................... approx. 30% of Full Power
P-20 .................................................................... approx. 20% of Full Power
P-10 .................................................................... approx. 10% of Full Power
P-0 ...................................................... No power throughout the cooking time
SENSOR COOKING pads, DEFROST pads, ONE-TOUCH COOKING pads,
Memory Cook pad, Number selection pads, Power Level pad, Timer / Pause pad,
Clock pad, Auto Fan, Plus 1 Miute pad, Turntable On / Off pad, START pad
Work Light pad, Night Light pad, FAN HI / LO pad, Clear/Off pad
Oven Cavity Light
20W x 1 Incandescent light bulb
Safety Standard
UL Listed
FCC Authorized
DHHS Rules, CFR, Title 21, Chapter 1, Subchapter J
Weight
Approx. 56 lbs.
GENERAL INFORMATION
GROUNDING INSTRUCTIONS
This oven is equipped with a three prong grounding plug. It must be plugged into a wall receptacle that is properly installed and
grounded in accordance with the National Electrical Code and local codes and ordinances.
In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric
current.
WARNING:
Improper use of the grounding plug can result in a risk of electric shock.
4
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
Electrical Requirements
The oven is equipped with a 3-prong grounding plug. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE
GROUNDING PIN FROM THE PLUG.
The power supply cord and plug must be connected to a separate 120 Volt AC, 60 Hz, 15 Amp. or more dedicated line, using
a grounded receptacle. The receptacle should be located inside the cabinet directly above the Microwave Oven/Hood system
mounting location.
3-Pronged Plug
Grounded
Receptacle Box
Grounding Pin
3-Pronged Receptacle
OVEN DIAGRAM
9
9
1
8
3
5
7
14
2
6
4
12
13
10
11
1.
2.
3.
4.
5.
Oven door with see-through window.
Door hinges.
Stirrer cover.
Turntable motor shaft.
Oven lamp.
It will light when oven is operating or door is open.
6. Door latches.
The oven will not operate unless the door is securely closed.
7. Auto-Touch control panel.
5
8. Time display: Digital display, 99 minutes 99 seconds.
9. Ventilation openings.
10. Light Cover.
11. Grease filters.
12. Removable turntable.
The turntable will rotate clockwise or counterclockwise.
Only remove for cleaning.
13. Removable turntable support.
14. Power supply cord
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
CONTROL PANEL
GLMV169DB / GLMV169DQ
GLMV169DS / PLMV169DC
(Colors will vary)
6
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
OPERATION
DESCRIPTION OF OPERATING SEQUENCE
The following is a description of component functions during
oven operation.
of the primary interlock switch, and door sensing switch
is mechanically associated with the door so that it will
function in the following sequence.
(1) When the door opens from a closed position, the
secondary interlock relay, door sensing switch, and
primary interlock switch open their contacts, and then
the monitor switch contacts close.
(2) When the door is closed from the open position, the
monitor switch contacts first open, and then the
contacts of the primary interlock switch close.
If the primary interlock switch fail with their contacts closed
when the door is opened, the closing of the monitor switch
contacts will form a short circuit through the C/T fuse, primary
interlock switch and causing the C/T fuse to blow.
OFF CONDITION
Closing the door activates the door sensing switch and
secondary interlock switch. (In this condition, the monitor
switch contacts are opened.)
When oven is plugged in, 120 volts A.C. is supplied to the
control unit. (Figure O-1).
1. The display will show "WELCOME, PRESS CLEAR AND
PRESS CLOCK".
To set any program or set the clock, you must first touch
the STOP/CLEAR pad. The display will clear, and " : "
will appear .
POWER LEVEL P-0 TO P-90 COOKING
COOKING CONDITION
When Variable Cooking Power is programmed, the 120 volts
A.C. is supplied to the power transformer intermittently
through the contacts of relay (RY2) which is operated by the
control unit within an interval second time base. Microwave
power operation is as follows:
Program desired cooking time touching the NUMBER pads.
When the START pad is touched, the following operations
occur:
1. The contacts of relays are closed and components
connected to the relays are turned on as follows.
(For details, refer to Figure O-2)
RELAY
RY1
RY2
RY3
RY4
VARI-MODE
ON TIME
Power 10(P-HI)
32 sec.
(100% power)
Power 9(P-90)
30 sec.
(approx. 90% power)
Power 8(P-80)
26 sec.
(approx. 80% power)
Power 7(P-70)
24 sec.
(approx. 70% power)
Power 6(P-60)
22 sec.
(approx. 60% power)
Power 5(P-50)
18 sec.
(approx. 50% power)
Power 4(P-40)
16 sec.
(approx. 40% power)
Power 3(P-30)
12 sec.
(approx. 30% power)
Power 2(P-20)
8 sec.
(approx. 20% power)
Power 1(P-10)
6 sec.
(approx. 10% power)
Power 0(P-0)
0 sec.
(0% power)
CONNECTED COMPONENTS
Oven lamp / Fan motor / Stirrer motor
Power transformer
Turntable motor
Hood fan motor
2. 120 volts A.C. is supplied to the primary winding of the
power transformer and is converted to about 3.3 volts
A.C. output on the filament winding, and approximately
2000 volts A.C. on the high voltage winding.
3. The filament winding voltage heats the magnetron filament
and the H.V. winding voltage is sent to a voltage doubler
circuit.
4. The microwave energy produced by the magnetron is
channelled through the waveguide into the cavity feedbox, and then into the cavity where the food is placed to
be cooked.
5. Upon completion of the cooking time, the power
transformer, oven lamp, etc. are turned off, and the
generation of microwave energy is stopped. The oven
will revert to the OFF condition.
6. When the door is opened during a cook cycle, monitor
switch, door sensing switch, primary interlock switch, and
secondary interlock relay are activated with the following
results. The circuits to the stirrer motor, the cooling fan
motor, the turntable motor, and the high voltage
components are de-energized, and the digital read-out
displays the time still remaining in the cook cycle when
the door was opened.
7. The monitor switch is electrically monitoring the operation
OFF TIME
0 sec.
2 sec.
6 sec.
8 sec.
10 sec.
14 sec.
16 sec.
20 sec.
24 sec.
26 sec.
32 sec.
Note: The ON/OFF time ratio does not correspond with the
percentage of microwave power, because approx.
2 seconds are needed for heating of the magnetron
filament.
BREAKFARST, LUNCH, DINNER
BREAKFAST, LUNCH, DINNER will automatically compute
the microwave power and cooking time. Set the desired
7
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
program by touching one of the BREAKFAST, LUNCH,
DINNER pads, and number pad to select menu. Enter the
weight or quantity by touching the Number pads. When the
START pad is touched, the following operations occur:
1. The COOK indicator will light.
2. The cooking time will appear on the display and start
counting down to zero. The cooking time is adjusted
automatically according to the weight of the food.
3. The shut-off relays (RY1, RY2 and RY3) are energized,
turning on the oven lamp, turntable motor, cooling fan
motor and convection motor. The power supply voltage
is applied to the heating element.
4. Now, the oven is in the microwave cooking mode.
3. RE-CIRCULATION (INSIDE VENTING)
The air handing is the same as VERTICAL VENTING
except that the final air discharge is directed horizontally
through the upper front of the oven into the kitchen. IN
this case, the accessory charcoal filter RK-230 must be
provided to filter the air before it leaves the oven.
AIR FLOW
HOOD FAN MOTOR
HOOD EXHAUST
LOUVER
HOOD
INTAKE
DUCT
COMPU DEFROST COOKING
The COMPU DEFROST key is a special function key to
defrost meats and poultry faster and better. COMPU
DEFROST automatically defrosts roast beef, etc.. Touch
the COMPU COOK pad and number pad to select menu and
enter the food weight by touching the number pads. When
the START pad is touched, the oven will cook according to
the special cooking sequence.
VENTILATION METHODS HOT AIR EXHAUST
1. VERTICAL VENTING
For this venting method, hot air rising from the
conventional range below is drawn in by the hood fan
motor through the grease filters at the right and left sides
of the base cover, up through the right and left sides of
the oven cavity, then discharged vertically at rear center
top of the oven, into the customer's vent system.
AIR FLOW
TO DUCT
TO DUCT
HOOD FAN MOTOR
HOOD
INTAKE
DUCT
GREASE
FILTER
2. HORIZONTAL VENTING
The air handing is the same as VERTICAL VENTING
except that the final air discharge is directed horizontally
out from the top rear of the oven into the customer's vent
system.
AIR FLOW
HOOD FAN MOTOR
TO DUCT
HOOD
INTAKE
DUCT
GREASE
FILTER
8
CHARCOAL
FILTER
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
any vapor from the oven cavity and sensor.
NOTE: During this first stage, do not open the door or
touch STOP/CLEAR pad.
4. When the sensor detects the vapor emitted from the
food, the display switches over to the remaining
cooking time and the timer counts down to zero.
At this time, the door may be opened to stir food, turn
it or season, etc.
5. When the timer reaches zero, an audible signal
sounds.The shut-off relay and cook relay are deenergized and the power transformer, oven lamp, etc.
are turned off.
6. Opening the door or touching the STOP/CLEAR pad,
the time of day will reappear on the display and the
oven will revert to an OFF condition.
SENSOR COOKING CONDITION
Using the SENSOR function, food is cooked without figuring
time, power level or quantity. When the oven senses enough
steam from the food, it relays the information to its
microprocessor which will calculate the remaining cooking
time and power level needed for best results. When the food
is cooked, water vapor is developed. the sensor "senses" the
vapor and its resistance increase gradually. When the
resistance reaches the value set according to the menu,
supplementary cooking is started.
The time of supplementary cooking is determined by experiment with each food category and inputted into the LSI. An
example of how sensor works: (Potatoes)
1. Potatoes at room temperature. Vapor is emitted very
slowly.
MIC
RO
WA
VE
2.Heat Potatoes. Moisture and humidity is emitted very
rapidly. You can smell the aroma as it cooks.
AH SENSOR
MIC
RO
WA
VE
Cooking Sequence.
1. Touch one of the Sensor Cooking pads. And then touch
START/TOUCH ON pad.
NOTE: The oven should not be operated on Sensor Cooking
immediately after plugging in the unit. Wait two
minutes before cooking on Sensor Cooking.
2. The coil of shut-off relays (RY1 and RY3) are energized,
the oven lamp, turntable motor and cooling fan motor are
turned on, but the power transformer is not turned on.
3. After about 32 seconds, the cook relay (RY2) is energized.
The power transformer is turned on, microwave energy
is produced and first stage is started.
9
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED
2. CLOCK APPEARS ON DISPLAY
FUSE
ORG
BLK
BLK
BLK
ORG
OVEN THERMAL
CUT OUT
RED
CONTROL UNIT
ORG
RED
BLK
ORG
C/T
RED
BLK
N.O.
C3
COM
A5
BLK
RED
BLK
SECONDARY
INTERLOCK
RELAY
RY4
B1
YLW
RY2
E2
BLK
HOOD FAN
THERMAL
CUT OUT
POWER
TRANSFORMER
GRN
MAGNETRON
STOP
SWITCH
RY5
High
B3
Low
WHT
WHT
A1
E1
RY6
RY7
A9
A7
COM
MONITOR
SWITCH
HUMIDITY
SENSOR
F2
F1
C1
COM.
COM.
N.O.
HIGH
VOLTAGE
CAPACITOR
N.C.
BLK
RED
RED
RED
BLK
WHT
COM
WHT
WHT
WHT
WHT
WHT
WHT
WHT
WHT
BLU
BLU
BLU
GRY
WHT
HIGH
VOLTAGE
RECTIFIER
FM
FAN
MOTOR
STM
OVEN
LAMP
TURNTABLE
MOTOR
WHT
WHT
BLU
YLW
RED
BLU
STIRRER
MOTOR
OL
TTM
HL
WHT
HOOD
LAMP
HL
RED
BLK
WHT
WHT
ORG
PPL
RED
HOOD
MOTOR
YLW
GRY
WHT
BLU
A3
BLK
F3
TURN-TABLE
MOTOR
RELAY
RY1
HOOD
CAPACITOR
GND
BLK
OVEN
LAMP
RELAY
RED
BLK
GRN
120VAC
60Hz
RY3
ORG
NC
C5
N.O.
PRIMARY
INTERLOCK
SWITCH
Figure O-1. Oven Schematic-Off Condition
SCHEMATIC
NOTE: CONDITION OF OVEN
1. DOOR CLOSED
2. COOKING TIME PROGRAMMED
3. VARIABLE COOKING CONTROL "HIGH"
4. "START" PAD TOUCHED
FUSE
ORG
BLK
BLK
BLK
ORG
OVEN THERMAL
CUT OUT
RED
CONTROL UNIT
ORG
RED
BLK
ORG
C/T
RED
BLK
N.O.
C3
COM
A5
BLK
RED
BLK
YLW
SECONDARY
INTERLOCK
RELAY
RY4
B1
RY2
E2
BLK
HOOD FAN
THERMAL
CUT OUT
POWER
TRANSFORMER
GRN
MAGNETRON
STOP
SWITCH
RY5
High
B3
WHT
GND
BLK
OVEN
LAMP
RELAY
Low
HOOD
CAPACITOR
A1
E1
RY6
A9
RY7
A7
COM
MONITOR
SWITCH
HUMIDITY
SENSOR
F2
F1
C1
COM.
COM.
N.O.
N.C.
BLK
RED
RED
RED
BLK
GRY
WHT
WHT
WHT
WHT
COM
HIGH
VOLTAGE
RECTIFIER
FM
FAN
MOTOR
N.O.
PRIMARY
INTERLOCK
SWITCH
Figure O-2. Oven Schematic-Cooking Condition
10
WHT
WHT
STM
OVEN
LAMP
TURNTABLE
MOTOR
WHT
WHT
OL
WHT
WHT
HIGH
VOLTAGE
CAPACITOR
STIRRER
MOTOR
TTM
WHT
WHT
WHT
BLU
RED
YLW
HL
BLU
BLU
BLU
BLU
HL
WHT
HOOD
LAMP
WHT
ORG
PPL
YLW
HOOD
MOTOR
RED
GRY
WHT
BLU
A3
BLK
F3
TURN-TABLE
MOTOR
RELAY
RY1
RED
BLK
120VAC
60Hz
WHT
RED
BLK
GRN
RY3
ORG
NC
C5
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
DESCRIPTION AND FUNCTION OF COMPONENTS
CAUTION: BEFORE REPLACING A BLOWN C/T FUSE
TEST THE DOOR SENSING SWITCH,
SECONDARY INTERLOCK RELAY (RY2),
PRIMARY INTERLOCK SWITCH AND MONITOR SWITCH FOR PROPER OPERATION.
(REFER TO CHAPTER "TEST PROCEDURE").
NOTE: C/T FUSE, MONITOR SWITCH AND PRIMARY
INTERLOCK SWITCH ARE REPLACED AS AN
ASSEMBLY
DOOR OPEN MECHANISM
The door is opened by pulling the door handle, refer to the
Figure D-1.
Latch
Hook
Latch
Heads
Door
Sensing
Switch
THERMAL CUT-OUT (HOOD )
Door
This thermal cut-out located on the right base plate. It is
designed to automatically turn on the hood fan motor
whenever the hot air rising from the conventional range
below causes the temperature at the thermal cut-out to rise
to 140OF (60OC) or higher, thus removing this hot air from
around microwave oven. When the temperature around the
thermal cut-out drops to 113OF (45OC) or lower, the thermal
cut-out shuts off the hood fan motor.
Monitor
Switch
Primary
Interlock
Switch
Figure D-1. Door Open Mechanism
DOOR SENSING SWITCH, PRIMARY INTERLOCK
SWITCH
THERMAL CUT-OUT (CAVITY )
The primary interlock switch is mounted in the lower position
of the latch hook, the door sensing switch in the primary
interlock system is mounted in the upper position of the latch
hook is mounted on upper position of the latch hook. They are
activated by the latch heads on the door. When the door is
opened, the switches interrupt the circuit to all components.
A cook cycle cannot take place until the door is firmly closed
thereby activating both interlock switches. The primary
interlock system consists of the door sensing switch and
secondary interlock relay located on the control circuit board.
This thermal cut-out is located on the top of the oven cavity.
It is designed to prevent damage to the oven unit if the food
in the oven catches fire due to overheating produced by
improper setting of cooking time or failure of control unit.
Under normal operation, the thermal cut-out remains
closed. However, the thermal cut-out will open at 293OF
(145OC) causing the oven to shut down.
TURNTABLE MOTOR
The turntable motor rotates the turntable located on the
bottom of the oven cavity, so that the foods on the turntable
cook evenly during cooking. Turntable will turn in either
direction. The turntable motor can be turned off by touching
TURNTABLE ON/OFF pad.
MONITOR SWITCH
The monitor switch is activated (the contacts opened) by the
latch head on the door while the door is closed. The switch
is intended to render the oven inoperative by means of
blowing the C/T fuse when the contacts of the secondary
interlock relay (RY2) and primary interlock switch fail to open
when the door is opened.
COOLING FAN MOTOR
The cooling fan motor drives a blade which draws external
cool air. This cool air is directed through the air vanes
surrounding the magnetron and cools the magnetron. This
air is channelled through the oven cavity to remove steam
and vapors given off from the heating foods. It is then
exhausted through the exhausting air vents at the oven
cavity.
Functions:
1. When the door is opened, the monitor switch contact
close (to the ON condition) due to their being normally
closed. At this time the secondary interlock relay (RY2),
primary interlock switch are in the OFF condition (contacts
open) due to their being normally open contact switches.
And the contacts of relay (RY1) are in the ON condition
(contacts close).
2. As the door goes to a closed position, the monitor switch
contacts are first opened and then the door sensing
switch and the primary interlock switch contacts close.
(On opening the door, each of these switches operate
inversely.)
3. If the door is opened, and the secondary interlock relay
(RY2) and primary interlock switch contacts fail to open,
the C/T fuse blows simultaneously with closing of the
monitor switch contacts.
HOOD FAN MOTOR
The hood fan motor is a two-speed, single-phase, double
pole induction type, requiring a hood fan capacitor. It is
located outside the upper rear part of the oven cavity, is to
remove, from around the oven, hot air rising from the
conventional electric or gas range over which it is installed.
This air is then expelled either vertically or horizontally
through the customer supplied duct system, or discharged
back into the kitchen.
STIRRER MOTOR
11
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
The stirrer motor drives the stirrer fan to stir the microwave
radiation from the waveguide.
touching the WORK LIGHT pad or the NIGHT LIGHT pad.
And also the brightness can be varied to high or low by
touching the WORK LIGHT pad or the NIGHT LIGHT pad.
HOOD LAMP
The hood lamps are mounted at the hood lamp angle on the
base cover. The hood lamps can be turned off and on by
TROUBLESHOOTING GUIDE
Never touch any part in the circuit with your hand or an uninsulated tool while the power supply is
connected.
When troubleshooting the microwave oven, it is helpful to follow the Sequence of Operation in performing the checks. Many
of the possible causes of trouble will require that a specific test be performed. These tests are given a procedure letter
which will be found in the "Test Procedure "section.
IMPORTANT: If the oven becomes inoperative because of a blown C/T fuse, check the monitor switch, relay (RY1) secondary
interlock relay (RY2), door sensing switch , primary interlock switch before replacing the C/T fuse. If C/T fuse
is replaced, the monitor switch and primary interlock switch must also be replaced. Use part FFS-BA019/KiT
as an assembly.
IMPORTANT: Whenever troubleshooting is performed with the power supply cord disconnected. It may in, some cases,
be necessary to connect the power supply cord after the outer case has been removed, in this event,
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the leads to the primary of the power transformer.
5. Ensure that the leads remain isolated from other components and oven chassis by using insulation tape.
6. After that procedure, reconnect the power supply cord.
When the testing is completed
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Reconnect the leads to the primary of the power transformer.
5. Reinstall the outer case (cabinet).
6. Reconnect the power supply cord after the outer case is installed.
7. Run the oven and check all functions.
12
13
SENSOR
COOKING
CONDITION
MICROWAVE
COOKING
CONDITION
IDLE
CONDITION
OFF
CONDITION
POSSIBLE CASE AND
DEFECTIVE PARTS
Oven stops at 32 seconds after starting.
The oven stops and "ERROR" is displayed or does not end during
Sensor Cooking condition. (Oven does not shut off after a cup of water
is boiling by Sensor Cooking.)
Home fuse blows when power cord is plugged into wall receptacle.
Monitor fuse blows when power cord is plugged into wall receptacle.
Display does not illuminate when power cord is first plugged into wall
receptacle.
Display does not operate properly when STOP/CLEAR key is touched.
(The time of day should appear on the display with beep sound during
normal condition.)
Oven lamp does not light with door is opened.
Hood fan motor operates when power cord is first plugged into wall
receptacle.
Temperature of oven base seems more than 140ûF (60ûC) because of
operation of the range below. But hood fan motor does not turn on
automatically. (Normally, food fan motor should be operating at low
speed.)
Hood lights do not turn on when WORK LIGHT pad or NIGHT LIGHT pad
is pressed.
Hood fan motor does not rotate at all with touched FAN HI/LO pad.
Speed of the hood fan motor does not change when the FAN HI/LO pad is
touched for this function.
Oven lamp does not light in cook cycle. (But it does light when door is
opened.)
Fan motor does not operate. (Oven lamp and turntable motor operate.)
Turntable motor does not operate (Oven lamp lights and fan motor
operate.)
Oven does not go into cook cycle when START pad is touched
Oven seems to be operating but little or no heat is produced in oven load.
(Food incompletely cooked or not cooked at all at end of cook cycle.)
Oven goes into a cook cycle but extremely uneven heating is produced in
oven load (food).
Variable cooking does not operate properly except Cooking Power 10 (PHI) mode.
Function of COMPU DEFROST does not operate properly.
Stirrer motor does not operate. (Other parts operate.)
Oven goes into COMPU DEFROST but food is not defrosted well.
PROBLEM
Q
CK
CK
RE
CK
CK
RE
CK
RE
RE
RE
RE
P
O
N
N
N
N
N
M
L
K
J
I
H
G
F
E
D
C
B
A
CONDITION
TEST PROCEDURE
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
CK = Check / RE = Replace
R AH SENSOR
NOISE FILTER
LOW VOLTAGE
NO POWER AT OUTLET
SHORTED IN POWER CORD
OPENED OR SHORTED WIRING
HOOD MOTOR CAPACITOR
HOOD LAMP OR SOCKET
TURNTABLE OFF CONDITION
STIRRER MOTOR
TURNTABLE MOTOR
FAN MOTOR
OVEN LAMP OR SOCKET
FOIL PATERN ON P.W.B.
COMPU DEFROST
RELAY (RY-5)
RELAY (RY-4)
RELAY (RY-3)
RELAY (RY-2)
RELAY (RY-1)
KEY UNIT
CONTROL UNIT
HOOD FAN MOTOR
HOOD HERMAL CUT-OUT
C/T FUSE
MONITOR SWITCH
SECONDARY INTERLOCK SYSTEM
PRIMARY INTERLOCK SWITCH
TEMPERATURE FUSE OR THERMAL CUT-OUT
HIGH VOLTAGE CAPACITOR
H.V. RECTIFIER
POWER TRANSFORMER
MAGNETRON
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
A
COMPONENT TEST
MAGNETRON ASSEMBLY TEST
1.
2.
3.
4.
5.
6.
7.
8.
9.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
To test for an open filament, isolate the magnetron from the high voltage circuit. A continuity check
across the magnetron filament leads should indicate less than 1 ohm.
To test for a shorted magnetron, connect the ohmmeter leads between the magnetron filament leads
and chassis ground. This test should indicate an infinite resistance. If there is little or no resistance
the magnetron is grounded and must be replaced.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
MICROWAVE OUTPUT POWER
The following test procedure should be carried out with the microwave oven in a fully assembled condition
(outer case fitted).
HIGH VOLTAGES ARE PRESENT DURING THE COOK CYCLE, SO EXTREME CAUTION SHOULD
BE OBSERVED.
Power output of the magnetron can be measured by performing a water temperature rise test. This test
should only be used if above tests do not indicate a faulty magnetron and there is no defect in the following
components or wiring: silicon rectifier, high voltage capacitor and power transformer. This test will
require a 16 ounce (453cc) measuring cup and an accurate mercury thermometer or thermocouple type
temperature tester. For accurate results, the following procedure must be followed carefully:
1. Fill the measuring cup with 16 oz. (453cc) of tap water and measure the temperature of the water
with a thermometer or thermocouple temperature tester. Stir the thermometer or thermocouple
through the water until the temperature stabilizes. Record the temperature of the water.
2. Place the cup of water in the oven. Operate oven at POWER 10(HIGH) selecting more than 60
seconds cook time. Allow the water to heat for 60 seconds, measuring with a stop watch, second
hand of a watch or the digital read-out countdown.
3. Remove the cup from the oven and again measure the temperature, making sure to stir the
thermometer or thermocouple through the water until the maximum temperature is recorded.
4. Subtract the cold water temperature from the hot water temperature. The normal result should be
29.2 to 54.2OF(16.2 to 30.1OC) rise in temperature. If the water temperatures are accurately
measured and tested for the required time period the test results will indicate if the magnetron tube
has low power output (low rise in water temperature) which would extend cooking time or high power
output (high rise in water temperature) which would reduce cooking time. Because cooking time can
be adjusted to compensate for power output, the magnetron tube assembly should be replaced only
if the water temperature rise test indicates a power output well beyond the normal limits. The test
is only accurate if the power supply line voltage is 120 volts and the oven cavity is clean.
B
POWER TRANSFORMER TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the primary input terminals and measure the resistance of the transformer with an
ohmmeter. Check for continuity of the coils with an ohmmeter. On the R x 1 scale, the resistance
of the primary coil should be less than 1 ohm and the resistance of the high voltage coil should be
approximately 83.2 ohms; the resistance of the filament coil should be less than 1 ohm.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
14
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
(HIGH VOLTAGES ARE PRESENT AT THE HIGH VOLTAGE TERMINAL, SO DO NOT ATTEMPT TO
MEASURE THE FILAMENT AND HIGH VOLTAGE.)
C
HIGH VOLTAGE RECTIFIER TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the rectifier from the circuit. Using the highest ohm scale of the meter, read the resistance
across the terminals and observe, reverse the leads to the rectifier terminals and observe meter
reading. If a short is indicated in both directions, or if an infinite resistance is read in both directions,
the rectifier is probably defective and should be replaced.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: Be sure to use an ohmmeter that will supply a forward bias voltage of more than 6.3 volts.
D
HIGH VOLTAGE CAPACITOR TEST
1.
2.
3.
4.
5.
6.
7.
8.
E
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the capacitor is open, no high voltage will be available to the magnetron. isconnect input leads and
check for short or open between the terminals using an ohmmeter.
Checking with a high ohm scale, if the high voltage capacitor is normal, the meter will indicate
continuity for a short time and should indicate an open circuit once the capacitor is charged. If the
above is not the case, check the capacitor with an ohmmeter to see if it is shorted between either
of the terminals and case. If it is shorted, replace the capacitor.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
CAVITY THERMAL CUT-OUT TEST
1.
2.
3.
4.
5.
6.
7.
8.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the thermal cut-out terminals should indicate a closed circuit unless the
temperature of the thermal cut-out reaches approximately 293OF(145OC).
An open thermal cut-out indicates overheating of the oven, exchange the oven thermal cut-out and
check inside of oven cavity and for improper setting of cooking time or operation of control unit. Check
for restricted air flow through the vent holes of the oven cavity, especially the cooling fan and air
guide.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
C/T FUSE TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the C/T fuse terminals should indicate a closed circuit unless the temperature
of the C/T fuse reaches approximately 302OF(150OC). An open C/T fuse indicates overheating of the
magnetron. Check for restricted air flow to the magnetron, especially the cooling fan air guide.
15
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
CAUTION: IF THE TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM
TEMPERATURE, REPLACE TEMPERATURE FUSE.
5. If the C/T fuse is blown when the door is opened, check the secondary interlock relay, primary interlock
switch and monitor switch according to the "TEST PROCEDURE" for those switches before replacing
the blown monitor fuse.
CAUTION: BEFORE REPLACING A BLOWN C/T FUSE, TEST THE SECONDARY INTERLOCK
RELAY, PRIMARY INTERLOCK SWITCH, DOOR SENSING SWITCH AND MONITOR
SWITCH FOR PROPER OPERATION.
If the C/T fuse is blown by improper switch operation, the C/T fuse and monitor switch must be replaced
with "C/T fuse and monitor switch assembly" part number FFS-BA019/KIT, even if the monitor switch
operates normally. The C/T fuse and monitor switch assembly is comprised of a 20 ampere fuse and
switch.
6. Reconnect all leads removed from components during testing.
7. Reinstall the outer case (cabinet).
8. Reconnect the power supply cord after the outer case is installed.
9. Run the oven and check all functions.
F
PRIMARY INTERLOCK SWITCH TEST
1.
2.
3.
4.
5.
6.
7.
8.
G
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the secondary interlock switch.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
PRIMARY INTERLOCK SYSTEM TEST
DOOR SENSING SWITCH
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal
of the switch. The meter should indicate an open circuit with the door open and a closed circuit with
the door closed. If improper operation is indicated, replace the door sensing switch.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling
fan motor, stirrer motor and oven light will be activated by RY1.
SECONDARY INTERLOCK RELAY (RY2)
1. Disconnect the power supply cord, and then remove outer case.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check the
state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts
are closed, replace the circuit board entirely or the relay itself.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
16
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
H
COMPONENT TEST
MONITOR SWITCH TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Before performing this test, make sure that the secondary interlock switch and the primary interlock
relay are operating properly, according to the above Switch Test Procedure. Disconnect the wire
lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the
ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the
monitor switch actuator is pushed by a screw driver through the lower latch hole on the front plate of
the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in),
the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM) terminal
and check the continuity of the monitor circuit.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
of the oven cavity with the door opened (in this condition the plunger of the monitor switch is pushed in),
the meter should indicate an open circuit. If improper operation is indicated, the switch may be
defective. After testing the monitor switch, reconnect the wire lead to the monitor switch (COM)
terminal and check the continuity of the monitor circuit.
5. Reconnect all leads removed from components during testing.
6. Reinstall the outer case (cabinet).
7. Reconnect the power supply cord after the outer case is installed.
8. Run the oven and check all functions.
Black
White /White
Screw Driver
Primary
Interlock
Switch
Monitor
Switch
17
Ohmmeter
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
I
COMPONENT TEST
HOOD THERMAL CUT-OUT TEST
1.
2.
3.
4.
5.
6.
7.
8.
J
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
A continuity check across the thermal cut-out terminals should indicate an open circuit unless the
temperature of the thermal cut-out reaches approximately 140OF(60OC) or more. At that temperature,
the contacts will close. The thermal cut-out opens automatically at approximately 113OF(45OC).
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
HOOD FAN MOTOR TEST
1.
2.
3.
4.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the motor does not turn, touch the FAN HI / LO pad once (set hood fan motor power "HIGH") and
check voltage between pins "1" and "2" (Blue and Black wires) of the 6 pin connector. If 120 Volts
appear and the hood capacitor is good, replace the hood fan assembly. If 120 Volts does not appear,
check the motor circuit. The resistance values of motor terminals are as follows:
YLW
4
1
HOOD FAN
CAPACITOR
32 ⏐
5
Resistance between;
BLU
45 ⏐
20 ⏐
BLU (1)
BLK (2)
BLU (1)
BLK (2)
WHT (3)
AND
AND
AND
AND
AND
YLW (4)
YLW (4)
BLK (2)
WHT (3)
RED (5)
BLK
3
0Ω (Shorted)
32Ω
32Ω
20Ω
45Ω
BLU BLK WHT
1
2
3
2
RED
=
=
=
=
=
6-PIN CONNECTOR
OF HOOD FAN MOTOR
WHT
5.
6.
7.
8.
Reconnect all leads removed from components during testing.
Reinstall the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
18
4
5
YLW RED
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
K
COMPONENT TEST
TOUCH CONTROL PANEL ASSEMBLY TEST
The touch control panel consists of circuits including semiconductors such as LSI, ICs, etc. Therefore,
unlike conventional microwave ovens, proper maintenance cannot be performed with only a voltmeter and
ohmmeter.
In this service manual, the touch control panel assembly is divided into two units, Control Unit and Key
Unit, and also the Control Unit is divided into two units, LSI Unit and Power Unit, and troubleshooting by
unit replacement is described according to the symptoms indicated.
Before testing,
1) Disconnect the power supply cord, and then remove outer case. Refer to procedure of "HOOD
EXHAUST LOUVER REMOVAL", "REMOVAL OF OVEN FROM WALL" and "OUTER CASE
REMOVAL".
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
1. Key Unit.
NOTE ;
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Check key unit ribbon connection before replacement.
5) Reconnect all leads removed from components during testing.
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
The following symptoms indicate a defective key unit.
a) When touching the pads, a certain pad produces no signal at all.
b) When touching a number pad, two figures or more are displayed.
c) When touching the pads, sometimes a pad produces no signal.
If the key unit is defective.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Replace the key unit.
5) Reconnect all leads removed from components during testing.
19
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
6) Re-install the outer case (cabinet).
7) Reconnect the power supply cord after the outer case is installed.
8) Run the oven and check all functions.
2. Control Unit.
The following symptoms indicate a defective control unit. Before replacing the control unit, perform
the Key unit test (Procedure M) to determine if control unit is faulty.
2-1 In connection with pads.
a) When touching the pads, a certain group of pads do not produce a signal.
b) When touching the pads, no pads produce a signal.
2-2 In connection with indicators
a) At a certain digit, all or some segments do not light up.
b) At a certain digit, brightness is low.
c) Only one indicator does not light.
d) The corresponding segments of all digits do not light up; or they continue to light up.
e) Wrong figure appears.
f) A certain group of indicators do not light up.
g) The figure of all digits flicker.
2-3 Other possible problems caused by defective control unit.
a) Buzzer does not sound or continues to sound.
b) Clock does not operate properly.
c) Cooking is not possible.
When testing is completed,
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Reconnect all leads removed from components during testing.
5) Re-install the outer case (cabinet).
6) Reconnect the power supply cord after the outer case is installed.
7) Run the oven and check all functions.
KEY UNIT TEST
1.
2.
3.
4.
G2
8.
G3
G4
5.
6.
7.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
If the display fails to clear when the STOP/CLEAR pad is depressed, first verify the flat ribbon cable
is making good contact, verify that the door sensing switch (stop switch) operates properly; that is the
contacts are closed when the door is closed and open when the door is open. If the door sensing switch
(stop switch) is good, disconnect the flat ribbon cable that connects the key unit to the control unit and
make sure the door sensing switch is closed (either close the door or short the door sensing switch
connecter). Use the Key unit matrix indicated on the control panel schematic and place a jumper wire
between the pins that correspond to the STOP/CLEAR pad making momentary contact. If the control
unit responds by clearing with a beep the key unit is faulty and must be replaced. If the control unit does
not respond, it is faulty and must be replaced. If a specific pad does not respond, the above method
may be used (after clearing the control unit) to determine if the control unit or key pad is at fault.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
G5
G6
G7
G8
G9
G10
G11
G12
Reconnect the power supply cord
Sensor
Baked
Beverage
0
9
8
7
6
after the outer case is installed.
Reheat
Potato
Run the oven and check all
Auto
Memory
Fan
Poultry
Clock
Fish
Rice
Help
Fan
Cook
HI / LO
functions.
Night
Light
Dinner
Items
Lunch
Items
Breakfast
Items
Auto
Defrost
Work
Light
Turntable
On / Off
Timer /
Pause
G13 G1
L
Clear
Off
START
Frozen
Snacks
Frozen
Entrees
Frozen
Veggie
Power
Level
Ground
Meats
Plus
1 Min
3
2
Speed
Defrost
1
Fresh
Veggie
Popcorn
5
20
4
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
M
COMPONENT TEST
RELAY TEST
1.
2.
3.
4.
5.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
6. After that procedure, re-connect the power supply cord.
7. Remove the outer case and check voltage between Pin No. 7 of the 4 pin connector (A) and the
common terminal of the relay RY1 on the control unit with an A.C. voltmeter.
The meter should indicate 120 volts, if not check oven circuit.
RY1 and RY2 Relay Test
These relays are operated by D.C. voltage
Check voltage at the relay coil with a D.C. voltmeter during the microwave cooking operation.
DC. voltage indicated .................... Defective relay.
DC. voltage not indicated .............. Check diode which is connected to the relay coil. If diode is good,
control unit is defective.
RELAY SYMBOL
OPERATIONAL VOLTAGE
RY1
RY2(COOK)
RY3
RY4
RY5
Approx.
Approx.
Approx.
Approx.
Approx.
24.0V
24.0V
24.0V
24.0V
24.0V
D.C.
D.C.
D.C.
D.C.
D.C.
CONNECTED COMPONENTS
Oven lamp / Fan motor / Stirrer motor
Power transformer
Turntable motor
Hood motor
Hood motor (HIGH /LOW selection)
8. Disconnect the power supply cord, and then remove outer case.
9. Open the door and block it open.
10.Discharge high voltage capacitor.
11.Reconnect all leads removed from components during testing.
12.Re-install the outer case (cabinet).
13.Reconnect the power supply cord after the outer case is installed.
14.Run the oven and check all functions.
N
COMPU DEFROST TEST
(1) Place one cup of water in the center of the turntable tray in the oven cavity.
(2) Close the door, touch the " Auto Defrost " pad twice and touch the Number pad "5". And then touch the
"START" pad.
(3) The oven is in Compu Defrost cooking condition.
(4) The oven will operate as follows
WEIGHT
0.5lbs
1ST STAGE
LEVEL
TIME
70%
30sec.
2ND STAGE
LEVEL
TIME
50%
30sec.
3RD STAGE
LEVEL
TIME
40%
30sec.
4TH STAGE
LEVEL
TIME
30%
30sec.
(5) If improper operation is indicated, the control unit is probably defective and should be checked.
O
FOIL PATTERN ON THE PRINTED WIRING BOARD TEST
To protect the electronic circuits, this model is provided with a fine foil pattern added to the primary on the
PWB, this foil pattern acts as a fuse.
1. Foil pattern check and repairs.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Follow the troubleshooting guide given below for repair.
21
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
COMPONENT TEST
STEPS
OCCURRENCE
CAUSE OR CORRECTION
1
Only pattern at "a" is broken.
*Insert jumper wire J1 and solder.
2
Pattern at "a" and "b" are broken.
*Insert the coil RCILF2003YAZZ between "c" and "d".
c
7
RY3
(J1)
b
a d
P
5) Make a visual inspection of the varistor.
Check for burned damage and examine
the transformer with a tester for the
presence of layer short-circuit (check
the primary coil resistance which is
approximately 780ý ± 10%). If any
abnormal condition is detected, replace
the defective parts.
T1
VRS1
CN - A
6) Reconnect all leads removed from components during testing.
7) Re-install the outer case (cabinet).
8) Reconnect the power supply cord after the outer case is installed.
9) Run the oven and check all functions.
2. Follow the troubleshooting guide given below, if indicator does not light up after above check and
repairs are finished.
1) Disconnect the power supply cord, and then remove outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power transformer.
5) Ensure that these leads remain isolated from other components and oven chassis by using
insulation tape.
6) After that procedure, re-connect the power supply cord.
7) Follow the troubleshooting guide given below for repair.
STEPS
1
2
8)
9)
10)
11)
12)
13)
14)
OCCURRENCE
CAUSE OR CORRECTION
The rated AC voltage is not present between
Pin No. 7 of the 4-pin connector (A) and the
common terminal of the relay RY1.
The rated AC voltage is present at primary
side of low voltage transformer.
Check supply voltage and oven power cord.
Low voltage transformer or secondary circuit defective.
Check and repair.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
22
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
P
COMPONENT TEST
AH SENSOR TEST
Checking the initial sensor cooking condition
WARNING :The oven should be fully assembled before following procedure.
(1) The oven should be plugged in at least two minutes before sensor cooking.
(2) Room temperature should not exceed 95°F (35°C).
(3) The unit should not be installed in any area where heat and steam are generated. The unit should
not be installed, for example, next to a conventional surface unit. Refer to the “INSTALLATION
INSTRUCTIONS” of the operation manual.
(4) Exhaust vents are provided on the back of the unit for proper cooling and air flow in the cavity. To
permit adequate ventilation, be sure to install so as not to block these vents. There should be some
space for air circulation.
(5) Be sure the exterior of the cooking container and the interior of the oven are dry. Wipe off any moisture
with a dry cloth or paper towel.
(6) The Sensor works with food at normal storage temperature. For example, chicken pieces would be
at refrigerator temperature and canned soup at room temperature.
(7) Avoid using aerosol sprays or cleaning solvents near the oven while using Sensor settings. The
sensor will detect the vapour given of by the spray and turn off before food is properly cooked.
(8) If the sensor has not detected the vapour of the food, ERROR will appear and the oven will shut off.
Water load cooking test
WARNING :The oven should be fully assembled before following procedure.
Make sure the oven has been plugged in at least two minutes before checking sensor cook operation.
The cabinet should be installed and screws tightened.
(1) Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
(2) Place the container on the center of tray in the oven cavity.
(3) Close the door.
(4) Touch Sensor reheat pad once and touch the Start pad, Now, the oven is in the sensor cooking
condition and “SENSOR REHEAT” and “COOK” will appear in the display.
(5) The oven will operate for the first 16 seconds, without generating microwave energy.
NOTE: ERROR will appear if the door is opened or Clear/Off pad is touched during first stage of
sensor cooking.
(6) After approximately 32 seconds, microwave energy is produced, and the display should start to count
down the remaining cooking time and oven should turn off after water is boiling (bubbling).
If the oven does not turn off, replace the AH sensor or check the control unit, refer to explanation below.
TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT
To determine if the sensor is defective, the simplest method is to replace it with a new replacement
sensor.
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Remove the AH sensor.
(5) Install the new AH sensor.
(6) Reconnect all leads removed from components during replacing.
(7) Re-install the outer case (cabinet).
(8) Reconnect the power supply cord after the outer case is installed.
(9) Reconnect the oven to the power supply cord and check the sensor cook operation proceed as
follows:
9-1. Fill approximately 200 milliliters (7.2 oz) of tap water in a 1000 milliliter measuring cup.
9-2. Place the container on the center of tray in the oven cavity.
9-3. Close the door.
9-4. Touch Sensor reheat pad once and touch the Start pad.
9-5. The control panel is in automatic Sensor operation.
9-6. The display will start to count down the remaining cooking time, and the oven will turn off
automatically after the water is boiling (bubbling).
If new sensor dose not operate properly, the problem is with the control unit, and refer to explanation below.
23
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
CHECKING CONTROL UNIT
(1) Disconnect the power supply cord, and then remove outer case.
(2) Open the door and block it open.
(3) Discharge high voltage capacitor.
(4) Disconnect the sensor connector that is mounted to control panel.
(5) Then connect the dummy resistor circuit (see fig.) to the sensor connector of control panel.
(6) Disconnect the leads to the primary of the power transformer.
(7) Ensure that these leads remain isolated from other components and oven chassis by using insulation
tape.
(8) After that procedure, re-connect the supply.
(9) Check the sensor cook operation proceed as follows:
9-1. Touch Sensor reheat pad once and touch the Start pad.
9-2. The control panel is in the sensor cooking operation.
9-3. After approximately 32 seconds, push plunger of select switch for more than 3 seconds. This
condition is same as judgement by AH sensor.
9-4. After approximately 3 seconds, the display shows “ X X . X X “ which is the remaining cooking
time, and the display count down.
If the above is not the case, the control unit is probably defective.
If the above is proper, the AH sensor is probably defective.
(10) Disconnect the power supply cord, and then remove outer case.
(11) Open the door and block it open.
(12) Discharge high voltage capacitor.
(13) Disconnect the dummy resistor circuit from the sensor connector of control panel.
(14) Carry out necessary repair.
(15) Reconnect all leads removed from components during testing and repairing.
(16) Re-install the outer case (cabinet).
(17) Reconnect the power supply cord after the outer case installed. Run the oven and check all function.
(18) Carry out “Water load cooking test” again and ensure that the oven works properly.
Plunger
R1, R2 : 22Ω ± 1% 1/2W
R3 : 4.3kΩ ± 5% 1/4W
R4 : 1MΩ ± 5% 1/4W
F-1
F-2
To connector (F)
on Control Unit.
1
2
3
NO
COM
COM NO
R1
F-3
CONNECTOR
NC
R2
R3
R4
Sensor Dummy Resistor Circuit
24
NC
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TEST PROCEDURES
PROCEDURE
LETTER
P
COMPONENT TEST
NOISE FILTER TEST
1.
2.
3.
4.
5.
Disconnect the power supply cord, and then remove outer case.
Open the door and block it open.
Discharge high voltage capacitor.
Disconnect the leads to the primary of the power transformer.
Using an ohm-meter, check between the terminals as described in the following table:
NOISE FILTER UNIT
MONITOR
FUSE
NOISE SUPPRESSION COIL
LINE CROSS CAPACITOR
LINE BYPASS CAPACITOR
0.22uF/ AC 250V
LINE BYPASS CAPACITOR
0.0033uF/ AC
0.0033uF/ AC
125V
125V
GRY
MEASURING POINT
RED
INDICATION OF OHM-METER
Between N and H
Open Circuit
Between terminal N and GRY
Short Circuit
Between terminal H and RED
Short Circuit
If incorrect readings are obtained, replace the noise filter.
6.
7.
8.
9.
Reconnect all leads removed from components during testing.
Re-install the outer case (cabinet).
Reconnect the power supply cord after the outer case is installed.
Run the oven and check all functions.
25
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
TOUCH CONTROL PANEL ASSEMBLY
OUTLINE OF TOUCH CONTROL PANEL
The touch control section consists of the following units
as shown in the touch control panel circuit.
7) Relay Circuit
To drive the magnetron, fan motor, stirrer motor, turntable
motor, hood motor, and light the oven lamp and hood lamp.
(1) Key Unit
(2) Control Unit (The Control unit consists of LSI Unit and
Power U nit)
8) Indicator Circuit
This circuit consists of 40 segments and 16 common
electrodes using a Light Crystal Display.
The Light Crystal Display (LCD) is drived by LCD driver
IC3.
The principal functions of these units and the signals communicated among them are explained below.
Key Unit
The key unit is composed of a matrix, signals generated in
the LSI are sent to the key unit through P10-P17.
When a key pad is touched, a signal is completed through
the key unit and passed back to the LSI through P41, P42,
AN8, AN9, AN10 and AN11 to perform the function that was
requested.
9) Back Light Circuit
A circuit to drive the back light (Light emitting diodes LD1LD10).
10) Absolute Humidity Sensor Circuit
This circuit detects moisture of the cooking food to allow
its automatic cooking.
Control Unit
Control unit consists of LSI, power source circuit, synchronizing signal circuit, ACL circuit, buzzer circuit, relay circuit
indicator circuit and back light circuit.
1) LSI
This LSI controls the key strobe signal, relay driving signal
for oven function and indicator signal.
2) Power Source Circuit
This circuit generates voltages necessary for the control
unit from the AC line voltage.
In addition, the synchronizing signal is available in order to
compose a basic standard time in the clock circuit.
Symbol
Voltage
Application
VC
-5.1V
LSI(IC1)
3) Synchronizing Signal Circuit
The power source synchronizing signal is available in order
to compose a basic standard time in the clock circuit. It
incorporates a very small error because it works on
commercial frequency.
4) ACL Circuit
A circuit to generate a signals which resetting the LSI to the
initial state when power is applied.
5) Buzzer Circuit
The buzzer is responds to signals from the LSI to emit
audible sounds (key touch sound and completion sound).
6) Door Sensing Switch
A switch to inform the LSI if the door is open or closed.
26
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
DESCRIPTION OF LSI
LSI(IZA958DR)
The I/O signal of the LSI(IZA958DR) is detailed in the following table.
Pin No.
Signal
I/O
Description
1
AN10
IN
Signal coming from touch key.
When either G10 line on key matrix is touched, a corresponding signal out of P10, P11,
P12, P13, P14 and P17 will be input into AN10. When no key is touched, the signal is held
at "H" level.
2
AN11
IN
3
AVSS
IN
Signal similar to AN10.
When either G9 line on key matrix is touched, a corresponding signal will be input into
AN11.
Connected to VC.
4
P10
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G8 line keys on key matrix is touched.
5
P11
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G7 line keys on key matrix is touched.
6
P12
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G6 line keys on key matrix is touched.
7
P13
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G5 line keys on key matrix is touched.
8
P14
OUT
9
P15
OUT
10
P16
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G4 line keys on key matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G3 line keys on key matrix is touched.
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN9, AN10, AN11, P41 and
P42 terminal while one of G2 line keys on key matrix is touched.
11
P17
OUT
12
13
X1
X2
IN
OUT
14
VSS
IN
15
OSC2
OUT
16
OSC1
IN
17
TEST
IN
18
RES
IN
19
P20
OUT
Key strobe signal.
Signal applied to touch-key section. A pulse signal is input to AN8, AN9, AN10, AN11,
P41 and P42 terminal while one of G1 line keys on key matrix is touched.
Connected to GND.
Terminal not used.
Power source voltage:-5V.
VC voltage of power source circuit input.
Internal clock oscillation frequency control output.
Output to control oscillation input of OSC2.
Internal clock oscillation frequency input setting.
The internal clock frequency is set by inserting the ceramic filter oscillation circuit with
respect to OSC1 terminal.
Connected to VC.
Auto clear terminal.
Signal is input to reset the LSI to the initial state when power is applied. Temporarily set
to "L" level the moment power is applied, at this time the LSI is reset. Thereafter set at
"H" level.
Signal to sound buzzer (2.0kHz).
A: key touch sound.
0.1 sec
A
B: Completion sound.
2.0 sec
B
27
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
Pin No.
20-22
23
Signal
I/O
Description
P21-P23
OUT
Terminal not used.
P24
OUT
Oven lamp and Fan motor driving signal.
To turn on and off the shut off relay(RY1). The square waveform voltage is delivered to
the RY1 driving circuit and RY2 control circuit.
16.7 msec.
H : GND
L : -5V
During cooking
24
P25
OUT
Magnetron high-voltage circuit driving signal.
To turn on and off the cook
relay(RY2). In P-HI operation, the
signals holds "L" level during microwave cooking and "H" level
while not cooking. In other cooking modes (P-90,P-80,P-70,P60,P-50,P-40,P-30,P-20,P-10,P0) the signal turns to "H" level and
"L" level in repetition according to
the power level.
25
26
27
P26
P27
P30
OUT
OUT
OUT
VARI-MODE
P-HI (100% power)
P-90 (approx. 90% power)
P-80 (approx. 80% power)
P-70 (approx. 70% power)
P-60 (approx. 60% power)
P-50 (approx. 50% power)
P-40 (approx. 40% power)
P-30 (approx. 30% power)
P-20 (approx. 20% power)
P-10 (approx. 10% power)
P-0 (0% power)
Hood motor driving signal.
To turn on and off relay(RY4). "L" level: During
Hood motor ON. "H" level: During Hood motor
OFF.
OFF TIME
0 sec.
2 sec.
6 sec.
8 sec.
10 sec.
14 sec.
16 sec.
20 sec.
24 sec.
26 sec.
32 sec.
H : GND
OFF
L
ON
Hood motor high / low driving signal.
To turn on and off relay(RY5). "L" level: During
Hood motor high. "H" level: During Hood motor
low.
Hood lamp driving signal.
To turn on and off solid state relay(SSR1). " 1 "
level: During Hood lamp ON (WORK LIGHT level).
" 2
" level: During Hood lamp ON (NIGHT
LIGHT level). "H" level: During Hood lamp OFF.
ON TIME
32 sec.
30 sec.
26 sec.
24 sec.
22 sec.
18 sec.
16 sec.
12 sec.
8 sec.
6 sec.
0 sec.
H : GND
OFF
L
ON
AC
CURRENT
WORK
LIGHT
H
1
L
NIGHT
LIGHT
H
2
L
28
29
30-34
35
P31
OUT
Turntable motor driving signal.
To turn on and off relay(RY3). "L" level: During
Turntable ON. "H" level: During Turntable OFF or
ON
during the oven is off condition.
Terminal not used.
Used for initial balancing of the bridge circuit (absolute humidity sensor)
Connected to GND.
P32-P37
P33-P37
CVCC
OUT
OUT
IN
VSS
IN
37-38
V3-V2
IN
39-40
V1-V0
IN
Power source voltage input terminal.
Standard voltage for LCD. Connected to GND.
VCC
IN
COM4-COM1
OUT
OUT
OUT
OUT
OUT
Power source voltage: GND (0V).
The power source voltage to drive the LSI is input to VCC terminal.
Terminal not used.
Terminal not used.
Data output terminal to LCD driver IC3.
Terminal not used.
Terminal not used.
36
41
42-45
46-65
66-79
80-85
86
SEG1-SEG20
P74-P91
SEG35-SEG40
P40
H : GND
OFF
L
Power source voltage:-5V.
The power source voltage to the LSI is input to VSS terminal. Connected to VC.
Terminal not used.
28
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
Pin No.
Signal
I/O
Description
87
P41
IN
Signal similar to AN10.
When either G13 line on key matrix is touched, acorresponding signal will be input into
P41.
88
P42
IN
Signal similar to AN10.
When either G12 line on key matrix is touched, acorresponding signal will be input into
P42.
89
IRQ0
IN
Signal synchronized with commercial power source frequency.
H : GND
This is the basic timing for time processing of LSI.
L : -5V
16.7 msec.
90
AVCC
IN
A/D converter power source voltage.
The power source voltage to drive the A/D converter in the LSI. Connected to GND.
91
AN0
IN
Used for initial balancing of the bridge circuit (absolute humidity sensor). This input is an
analog input terminal from the AH sensor circuit, and connected to the A/D converter built
into the LSI.
92
AN0-AN1
IN
AH sensor input.
This input is an analog input terminal from the AH sensor circuit, and connected to the
A/D converter built into the LSI.
IN
To input signal which communicates the door open/close information to LSI.
AN3
IN
Door closed; "H" level signal(0V).
Door opened; "L" level signal(-5V).
Terminal not used.
AN4-AN7
IN
Terminal to change cooking input according to the Model.
By using the A/D converter contained in the LSI, DC voltage in accordance with the Model
in operation is applied to set up its cooking constant.
99
AN8
IN
Input terminal to judge the model.
The signal out of P16 will be input into AN8 through G2 line on key matrix. The LSI will
judge the model by this signal.
100
AN9
IN
Signal similar to AN10.
93
94
95-98
AN2
When either G11 line on key matrix is touched, a corresponding signal will be input into
AN9.
29
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
ABSOLUTE HUMIDITY SENSOR CIRCUIT
(1) Structure of Absolute Humidity Sensor
The absolute humidity sensor includes two thermistors
as shown in the illustration. One thermistor is housed in
the closed vessel filled with dry air while another in the
open vessel. Each sensor is provided with the protective
cover made of metal mesh to be protected from the
external airflow.
balance the bridge circuit is deviated to increase the
voltage available at AN1 terminal of the LSI.
Then the LSI observes that voltage at AN1 terminal and
compares it with its initial value, and when the comparison
rate reaches the preset value (fixed for each menu to be
cooked), the LSI causes the unit to stop sensor cooking;
thereafter, the unit goes in the next operation
automatically.
When the LSI starts to detect the initial voltage at AN1
terminal 16 seconds after the unit has been put in the
Sensor Cooking mode, if it is not possible to balance, of
the bridge circuit due to disconnection of the absolute
humidity sensor, ERROR will appear on the display and
the cooking is stopped.
Thermistors
Sensing part
(Closed vessel)
1) Absolute humidity sensor circuit
R3
R1
S
R2
Operational
amplifier
Output
voltage
+
S : Thermistor
open vessel
C : Thermistor
closed vessel
C. Thermistor in
closed vessel
S. Thermistor in
open vessel
30
R99
300k
31
R100
150k
32
R101
75k
33
R102
37.4k
34
R97
S
Absolute humidity vs,
output voltage characteristic
VA : -15V
Absolute humidity (g/m 2 )
(3) Detector Circuit of Absolute Humidity Sensor Circuit
This detector circuit is used to detect the output voltage of
the absolute humidity circuit to allow the LSI to control
sensor cooking of the unit. When the unit is set in the
sensor cooking mode, 16 seconds clearing cycle occurs
than the detector circuit starts to function and the LSI
observes the initial voltage available at its AN1 terminal.
With this voltage given, the switches SW1 to SW5 in the
LSI are turned on in such a way as to change the
resistance values in parallel with R98 ~ R102 of IC2.
Changing the resistance values results in that there is the
same potential at both F-3 terminal of the absolute humidity
sensor and AN0 terminal of the LSI. The voltage of AN1
terminal will indicate about -2.5V. This initial balancing is
set up about 16 seconds after the unit is put in the Sensor
Cooking mode. As the sensor cooking proceeds, the food
is heated to generate moisture by which the resistance
30
VA : -15V
SW1
P33
P34
P35
P36
P37
0.01uF
R95
47k
D90
VC : -5V
SW2
SW3
SW4
SW5
AN0
LSI
(IC1)
C92
0.01uF
R93
360k
R94
10k
R90
F-2
R91
3.32k R92
1.8k
+
IC2
0.015uF
F-1
C
R96
F-3
3.57k
91
C93
47k
Output voltage
C
620k
R98
C91
(2) Operational Principle of Absolute Humidity Sensor
The figure below shows the basic structure of an absolute
humidity sensor. A bridge circuit is formed by two
thermistors and two resistors (R1 and R2).
The output of the bridge circuit is to be amplified by the
operational amplifier.
Each thermistor is supplied with a current to keep it
o
o
heated at about 150 C (302 F), the resultant heat is
dissipated in the air and if the two thermistors are placed
in different humidity conditions they show different
degrees of heat conductivity leading to a potential
difference between them causing an output voltage from
the bridge circuit, the intensity of which is increased as
the absolute humidity of the air increases. Since the
output is very minute, it is amplified by the operational
amplifier.
0.1
uF
Sensing part
(Open vessel)
C90
ventilation opening for sensing
92
AN1
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
SERVICING
1. Precautions for Handling Electronic Components
This unit uses CMOS LSI in the integral part of the
circuits. When handling these parts, the following
precautions should be strictly followed. CMOS LSI have
extremely high impedance at its input and output
terminals. For this reason, it is easily influenced by the
surrounding high voltage power source, static electricity
charge in clothes, etc. and sometimes it is not fully
protected by the built-in protection circuit.
In order to protect CMOS LSI.
1) When storing and transporting, thoroughly wrap them in
aluminium foil. Also wrap all PW boards containing them
in aluminium foil.
2) When soldering, ground the technician as shown in the
figure and use grounded soldering iron and work table.
4) Re-install the outer case (cabinet).
5) Re-connect the power supply cord after the outer
case is installed.
6) Run the oven and check all functions.
A. On some models, the power supply cord between the
touch control panel and the oven itself is so short that the
two can’t be separated. For those models, check and
repair all the controls (sensor-related ones included) of
the touch control panel while keeping it connected to the
oven.
B. On some models, the power supply cord between the
touch control panel and the oven proper is long enough
that they may be separated from each other. For those
models, it is possible to check and repair the controls of
the touch control panel while keeping it apart from the
oven proper; in this case you must short both ends of the
door sensing switch (on PWB) of the touch control panel
with a jumper, which activates an operational state that
is equivalent to the oven door being closed. As for the
sensor-related controls of the touch control panel,
checking them is possible if dummy resistor(s) with
resistance equal to that of the controls are used.
(2) Servicing the touch control panel with power supply
from an external power source:
Disconnect the touch control panel completely from the
oven proper, and short both ends of the door sensing
switch (on PWB) of the touch control panel, which
activates an operational state that is equivalent to the
oven door being closed. Connect an external power
source to the power input terminal of the touch control
panel, then it is possible to check and repair the controls
of the touch control panel it is also possible to check the
sensor-related controls of the touch control panel by
using the dummy resistor(s).
approx. 1M ohm
2. Shapes of Electronic Components
E
C
B
Transistor
2SB1238
Transistor
KRC243M
E
CB
3. Servicing of Touch Control Panel
We describe the procedures to permit servicing of the
touch control panel of the microwave oven and the
precautions you must take when doing so. To perform
the servicing, power to the touch control panel is available
either from the power line of the oven itself or from an
external power source.
(1) Servicing the touch control panel with power supply
of the oven:
CAUTION:
THE HIGH VOLTAGE TRANSFORMER OF THE
MICROWAVE OVEN IS STILL LIVE DURING
SERVICING AND PRESENTS A HAZARD.
Therefore, before checking the performance of the touch
control panel,
1) Disconnect the power supply cord, and then remove
outer case.
2) Open the door and block it open.
3) Discharge high voltage capacitor.
4) Disconnect the leads to the primary of the power
transformer.
5) Ensure that these leads remain isolated from other
components and oven chassis by using insulation
tape.
6) After that procedure, re-connect the power supply
cord.
After checking the performance of the touch control
panel,
1) Disconnect the power supply cord.
2) Open the door and block it open.
3) Re-connect the leads to the primary of the power
transformer.
4. Servicing Tools
Tools required to service the touch control panel
assembly.
1) Soldering iron: 30W
(It is recommended to use a soldering iron with a grounding
terminal.)
2) Oscilloscope: Single beam, frequency range: DC-10MHz
type or more advanced model.
3) Others: Hand tools
5. Other Precautions
1) Before turning on the power source of the control unit,
remove the aluminium foil applied for preventing static
electricity.
2) Connect the connectors of the key unit to the control unit
being sure that the lead wires are not twisted.
3) After aluminium foil is removed, be careful that abnormal
voltage due to static electricity etc. is not applied to the
input or output terminals.
4) Attach connectors, electrolytic capacitors, etc. to PWB,
making sure that all connections are tight.
5) Be sure to use specified components where high precision
is required.
31
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE
WARNING AGAINST HIGH VOLTAGE:
Microwave ovens contain circuitry capable of producing very high voltage and current, contact with following parts may
result in severe, possibly fatal, electric shock.
(Example)
High Voltage Capacitor, Power Transformer, Magnetron, High Voltage Rectifier Assembly, High Voltage Harness etc..
WARNING:
Avoid possible exposure to microwave energy. Please follow the instructions below before
operating the oven.
1. Disconnect the power supply cord.
2. Visually check the door and cavity face plate for damage
(dents, cracks, signs of arcing etc.).
4. The door is bent or warped.
5. There are defective parts in the door interlock system.
6. There are defective parts in the microwave generating
and transmission assembly.
7. There is visible damage to the oven.
Carry out any remedial work that is necessary before
operating the oven.
Do not operate the oven if any of the following conditions
exist;
1. Door does not close firmly.
2. Door hinge, support or latch hook is damaged.
3. The door gasket or seal is damaged.
Do not operate the oven:
1. Without the RF gasket (Magnetron).
2. If the wave guide or oven cavity are not intact.
3. If the door is not closed.
4. If the outer case (cabinet) is not fitted.
WARNING FOR WIRING
To prevent an electric shock, take the following precautions.
1. Before wiring,
1) Disconnect the power supply cord.
2) Open the door block it open.
3) Discharge the high voltage capacitor and wait for 60
seconds.
2. Don’t let the wire leads touch to the followiong parts;
1) High voltage parts:
Magnetron, High voltage transformer, High voltage
capacitor and High voltage rectifier assembly.
2) Hot parts:
Oven lamp, Magnetron, High voltage transformer
and Oven cavity.
3) Sharp edge:
Bottom plate, Oven cavity, Waveguide flange,
Chassis support and other metallic plate.
4) Movable parts (to prevent a fault)
Fan blade, Fan motor, Switch, Switch lever, Open
button.
3. Do not catch the wire leads in the outer case cabinet.
4. Insert the positive lock connector until its pin is locked
and make sure that the wire leads do not come off even
if the wire leads are pulled.
5. To prevent an error function, connect the wire leads
correctly, referring to the Pictorial Diagram.
Please refer to ‘OVEN PARTS, CABINET PARTS, CONTROL PANAL PARTS, DOOR PARTS’, when carrying out any of
the following removal procedures:
THE FOLLOWING ADJUSTMENTS OR COMPONENT REPLACEMENT CAN BE PERFORMED
WITHOUT REMOVING THE OVEN FROM THE WALL
1. Hood lamps, sockets and grease filter.
2. Oven lamp, base cover and hood lamp glass assembly.
3. Turntable motor.
4. Hood exhaust louver.
5. Control panel assembly or components
6. Stirrer cover and stirrer fan.
HOOD EXHAUST LOUVER REMOVAL
Push
Hood exhaust
louver
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screw holding the hood exhaust
louver to the oven cavity.
4. Pull the hood exhaust louver from the oven cavity by
pushing the right and left tabs of the hood exhaust louver
Tab (left )
Push
Tab (right)
32
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
to remove.
5. Remove the louver covers A, B, and C from the hood
exhaust louver
6. Now, the hood exhaust louver is free.
REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven)
1. Disconnect the power supply cord, and uncoil the power
supply cord.
2. Remove the turntable tray and support from the oven
cavity.
3. Remove the one (1) screw holding the exhaust damper
assembly to the rear stay, and remove the exhaust
damper assembly by sliding it backward.
4. Remove the two (2) screws holding the oven (outer case
cabinet) to the top cabinet.
5. Remove the hood exhaust louver referring to "HOOD
EXHAUST LOUVER REMOVAL".
6. While supporting the front of the oven, unfasten the two (2)
unit mounting screws holding the oven to the unit mounting
plate.
7. Remove the oven by sliding it into the arms of the unit
mounting plate and pull the power cord out of the wall
cabinet.
8. The oven is now free and can be placed on the work
surface selected for servicing the oven.
9. Installation is the reverse of this procedure.
OUTER CASE REMOVAL
Remove the oven from the wall and proceed as follows;
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove three (3) screws holding the hood exhaust louver
to the oven, and pull it forward to remove by pushing the
right and left tabs of the hood exhaust louver. (Refer to
procedure of "HOOD EXHAUST LOUVER REMOVAL".)
4. Remove four (4) screws holding the rear stay to the hood
fan motor or the oven, and remove it.
5. Remove the four (4) screws from the rear of the outer case
cabinet.
6. Slide the outer case cabinet back about 1 inch (3 cm) to
free it from retaining clips on the cavity face plate.
7. Disconnect the three (3) pin connector of the power supply
cord from the wiring harness and remove the power supply
cord together with the outer case.
8. Discharge high voltage capacitor.
CAUTION: 1. DISCONNECT OVEN FROM POWER
SUPPLY BEFORE REMOVING OUTER
CASE.
2. DISCHARGE THE HIGH VOLTAGE
CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.
POWER TRANSFORMER REMOVAL
1. Disconnect the power supply cord, remove the oven from
wall, and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer Case Removal".)
And proceed as follows.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove one (1) screw holding the hood duct to the oven
cavity front flange.
5. Disconnect the stop switch harness from the chassis
support and disconnect the wire leads from the fan motor.
6. Lift up the fan motor side of the hood duct.
7. Disconnect filament leads of transformer from the
magnetron and capacitor.
8. Disconnect high voltage leads of capacitor from the
transformer.
9. Disconnect wire leads from transformer.
10.Remove two (2) screws holding the transformer to right
base plate.
Re-install
1. Install by sliding the transformer on the right base plate
with its primary terminals toward the outer case.
2. Secure the transformer with two (2) screws to right base
plate.
3. Re-connect wire leads (primary and high voltage) to the
transformer and filament leads of transformer to magnetron
and high voltage capacitor. Refer to "PICTORIAL
DIAGRAM".
4. Re-install the hood duct holding the fan motor to the oven
cavity front flange with one (1) screw.
5. Re-connect the wire leads to the chassis support and the
fan motor, referring to "PICTORIAL DIAGRAM".
6. Re-install the outer case and check that oven is operating
properly.
CAUTION: MAKE SURE THE WIRE LEADS NEVER TOUCH
THE FAN BLADE.
HOOD FAN MOTOR, HOOD DUCT, OVEN LAMP SOCKET REMOVAL AND AH SENSOR REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
“Removal of Oven from Wall” and “Outer case Removal”
of the base model Service Manual)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the 6-pin connector of the hood fan motor
from the main wire harness located at the right edge of the
hood duct and release the snap band from the hood duct.
5. Remove the hood fan motor from the hood duct by lifting
it up.
6. Now, the hood fan motor is free.
33
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
7. Disconnect the connector CN-F from the control unit.
8. Remove one (1) screw holding the hood duct to the oven
cavity front plate.
9. Release the 6-pin connector and the 3-pin connector of
the main harness A from the hood duct.
10.Disconnect the wire leads from the fan motor and chassis
support, and release the wire leads from holes of the
hood duct.
11.Remove the two (2) unit mounting screws from the
chassis support (right side) and the hood duct (left side).
12.Remove the one (1) screw holding the chassis support.
13.Remove the chassis support.
14.Remove the hood duct from the oven cavity by lifting it up.
15.Screw the oven lamp off from the lamp socket.
16.Remove the lamp socket from the lamp angle.
17.Pull the wire leads from the oven lamp socket by pushing
the terminal hole of the oven lamp socket with a small flat
type screw driver.
18.Now, the oven lamp socket is free.
19.Release the harness of the AH sensor assembly from
three (3) wire holders of the hood duct.
20.Remove two (2) screws holding the AH sensor assembly
to the hood duct.
21.Now, the AH sensor assembly is free.
Oven lamp
socket
Terminal
Wire lead
Terminal hole
MAGNETRON REMOVAL
1. Disconnect the power supply cord , remove the oven from
wall and remove outer case (Refer to procedure of "Removal
of Oven from Wall" and "Outer case Removal".)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor and the
chassis support, and release them from the holes of hood
duct.
5. Remove the one (1) screw holding the hood duct to the oven
cavity front plate, and lift up the fan motor side of the hood
duct.
6. Remove the one (1) screw holding the capacitor holder to
the hood intake duct.
7. Disconnect the high voltage wire leads of the high voltage
rectifier assembly from the magnetron.
8. Disconnect the filament lead of the transformer from the
magnetron.
Flate type small
screw driver
9. Remove the power transformer from the right base plate,
referring to "POWER TRANSFORMER REMOVAL".
10.Carefully remove four (4) mounting screws holding the
magnetron to waveguide. When removing the screws hold
the magnetron to prevent it from falling.
11.Remove the magnetron from the unit with care so the
magnetron tube should not be hit by any metal object
around the tube.
12.Remove the one (1) screw holding the magnetron air guide
to the magnetron.
13.Remove the magnetron air guide
CAUTION: WHEN REPLACING THE MAGNETRON, BE
SURE THE R.F. GASKET IS IN PLACE AND
MOUNTING SCREWS ARE TIGHTENED SECURELY.
HIGH VOLTAGE RECTIFIER AND HIGH VOLTAGE CAPACITOR REMOVAL
voltage capacitor.
8. Disconnect high voltage wire from capacitor.
9. Remove one (1) screw holding capacitor holder and high
voltage rectifier to the hood intake duct.
10.Disconnect the high voltage rectifier assembly from the
high voltage capacitor.
11.Now, the high voltage rectifier assembly is free.
12.Remove capacitor from the holder.
13.Now, the high voltage capacitor is free.
CAUTION: WHEN REPLACING THE HIGH VOLTAGE RECTIFIER ASSEMBLY, THE GROUND SIDE TERMINAL MUST BE SECURED FIRMLY WITH A
GROUNDING SCREW.
1. Disconnect the power supply cord , remove the oven from
wall and remove outer case (Refer to procedure of "Removal
of Oven from Wall" and "Outer case Removal".)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor and the
chassis support, and release them from the holes of hood
duct.
5. Remove the one (1) screw holding the hood duct to the oven
cavity front flange, and lift up the fan motor side of the
hood duct.
6. Disconnect the high voltage wire leads with high voltage
rectifier from the magnetron.
7. Disconnect filament lead of the transformer from high
HOOD FAN THERMAL CUT-OUT REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the hood fan thermal
cut-out.
5. Remove one (1) screw holding the thermal cut-out to the
right base plate.
6. Remove the hood fan thermal cut-out from the right base
plate.
7. Now, the hood fan thermal cut-out is free.
34
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
THERMAL CUT-OUT (CAVITY) REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove two (2) unit mounting screws.
5. Remove the hood duct. (Refer to the procedure of " HOOD
FAN MOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL".
6. Straighten the tab holding the thermal cut-out to the top
plate of the oven cavity.
7 . Release the thermal cut-out (cavity) from the one slit of
the oven cavity top plate.
8. Disconnect the wire leads from the thermal cut-out (cavity).
9. Now, the thermal cut-out (cavity) is free.
NOTE: When the tab is broken or turned off, use the another
tab which is fixed near the slit when the new thermal
cut-out is replaced.
Top of Oven Cavity
Tab
Thermal
Cut-Out
Waveguide
Slit
Thermal
Cut-Out
(Cavity)
Thermal
Cut-Out
Tab
COOLING FAN MOTOR REMOVAL
1. Disconnect the power supply cord, remove the oven from
wall and remove outer case (Refer to procedure of "Removal
of Oven from Wall" and "Outer case Removal".)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Disconnect the wire leads from the fan motor and the
chassis support.
5. Remove one (1) screw holding the hood duct to oven
cavity.
6. Release the wire leads from the hole of the hood duct.
7. Lift up the fan motor side of the hood duct.
8. Remove the two (2) screws holding the fan motor to the
hood duct.
9. Remove the fan blade from the fan motor shaft according
the following procedure.
10.Hold the edge of the rotor of the fan motor by using a pair
of groove joint pliers.
CAUTION:
* Make sure that any pieces do not enter the gap
between the rotor and the stator of the fan motor
because the rotor is easily shaven by pliers and metal
pieces may be produced.
* Do not touch the pliers to the coil of the fan motor
because the coil may be cut or injured.
* Do not disfigure the bracket by touching with the
pliers.
11.Remove the fan blade from the shaft of the fan motor by
pulling and rotating the fan blade with your hand.
12. Now, the fan blade will be free.
CAUTION:
* Do not reuse the removed fan blade because the hole
(for shaft) may be larger than normal.
13.Now, the fan motor is free.
Coil
Groove joint pliers
Stator
Gap
Bracket
Rotor
Rear View
Shaft
Axis
Stator
These are the positions
that should be pinched
with pliers
Rotor
Side View
INSTALLATION
1. Install the fan blade to the fan motor shaft according to the
following procedure.
35
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
2. Hold the center of the bracket which supports the shaft of
the fan motor on the flat table.
3. Apply the screw lock tight into the hole (for shaft) of the
fan blade.
4. Install the fan blade to the shaft of fan motor by pushing
the fan blade with a small, light weight, ball peen hammer
or rubber mallet.
5. Install the fan motor to the hood duct with the two (2)
screws.
CAUTION:
* Do not hit the fan blade strongly when installing
because the bracket may be disfigured.
* Make sure that the fan blade rotates smooth after
installation.
* Make sure that the axis of the shaft is not slanted.
6. Install the hood duct to the oven cavity with the one (1)
screw.
7. Re-install the wire leads to the hole of the hood duct.
8. Connect the wire leads to the fan motor and chassis
support, referring to the pictorial diagram.
9. Refer to procedure of "OUTER CASE REMOVAL". And
reverse their procedure. And re-install the outer case.
Shaft
Table
Center of
bracket
TURNTABLE MOTOR REMOVAL
down and moving to the left slightly.
5. Disconnect the wire leads from the turntable motor.
6. Remove one (1) screw holding turntable motor to the oven
cavity.
7. Now the turntable motor is free.
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove the three (3) screws holding the base cover to the
oven cavity
4. Remove the base cover from the oven cavity by pulling
STIRRER MOTOR REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood fan motor and the hood duct from the
oven cavity, referring to the procedure of " HOOD FAN
MOTOR, HOOD DUCT AND OVEN LAMP SOCKET
REMOVAL".
5. Disconnect the wire leads from the stirrer motor.
6. Remove the two (2) screws holding the stirrer motor to the
waveguide of the oven cavity.
7. Remove the stirrer motor from the waveguide.
8. Now, the stirrer motor is free.
9. When installing the stirrer motor, the shaft of stirrer motor
must be inserted to the stirrer fan shaft. Refer to the
procedure of "STIRRER COVER AND STIRRER FAN
INSTALLATION".
STIRRER COVER AND STIRRER FAN INSTALLATION
Shaft
1. Put the stirrer fan on the stirrer cover to match the stirrer
fan shaft to the center of the stirrer support.
2. Insert the shaft of stirrer fan to the shaft of stirrer motor.
3. Insert the cutout of stirrer cover to the tabs on the ceiling.
4. Install the stirrer cover to the oven cavity, and secure it by
one canoe clip.
Stirrer Fan
Stirrer Cover
Canoe Clip
OVEN LAMP REMOVAL
1. Disconnect the power supply cord.
2. Remove three (3) screws holding the hood exhaust louver
to oven cavity front flange.
3. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
4.
5.
6.
7.
36
REMOVAL")
Lift the oven lamp cover up.
Now, the oven lamp and the socket are found.
Screw the oven lamp off from the lamp socket.
Now, the oven lamp is free.
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
CONTROL PANEL ASSEMBLY, CONTROL UNIT AND KEY UNIT REMOVAL
fixing plate.
16.Release the one (1) tab holding the LCD to the LCD holder.
17.Release the four (4) tabs holding the LSI unit to the LCD
holder.
18.Remove the LCD holder and the LED sheet.
19.Now, the control unit is free.
20.Remove the one (1) screw holding the key fixing plate to
the control panel.
21.Release the six (6) tabs holding the key fixing plate to the
control panel.
22.Remove the key fixing plate from the control panel.
23.Tear the key unit from the key fixing plate.
24.Now, the key unit is free
1. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove one (1) screw holding the hood exhaust louver to
oven cavity front flange.
4. Remove the hood exhaust louver from the oven by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL")
5. Remove one (1) screw holding the control panel to the
oven cavity front face plate.
6. Release the control panel from the oven cavity front face
plate by lifting it up.
7. Disconnect the wire leads from the relays RY1 and RY2.
8. Disconnect the connectors CN-A, CN-B and CN-E from
the control unit.
9. Remove the control panel assembly from the oven.
10.Now, the control panel assembly is free.
11.Disconnect the connector CN-G from the control unit.
12.Release the two (2) tabs of LCD holder from the two (2)
holes of the key fixing plate.
13.Release the four (4) tabs holding the LCD holder to the
tcontrol panel.
14.Remove two (2) screws holding the power unit to the key
fixing plate.
15.Release the two (2) tabs holding the power unit to the key
NOTES FOR KEY UNIT REPLACEMENT
1. Do not reuse the torn key unit because the performance
of the adhesive becomes weak.
2. Before attaching a new key unit, wipe off remaining
adhesive on the key fixing plate surfaces completely with
a soft cloth soaked in alcohol.
3. When attaching the key unit to the key fixing plate, adjust
the upper edge and right edge of the key unit to the correct
position of key fixing plate.
4. Stick the key unit firmly to the key fixing plate by rubbing
with soft cloth not to scratch.
POSITIVE LOCK® CONNECTOR (NO-CASE TYPE) REMOVAL
Terminal
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Push the lever of positive lock® connector.
5. Pull down on the positive lock® connector.
Positive lock¨
connector
4
Push
Lever
5
Pull down
®
CAUTION: WHEN CONNECTING THE POSITIVE LOCK
CONNECTORS TO THE TERMINALS, INSTALL
THE POSITIVE LOCK® SO THAT THE LEVER
FACES YOU.
Positive lock® connector
DOOR SENSING SWITCH, SECONDARY INTERLOCK SWITCH AND MONITOR SWITCH REMOVAL
9. Now, each switch is free.
Re-install
1. Re-install each switch in its place. The secondary
interlock switch is in the lower position, door sensing
switch is in the upper position, is in the upper vertical
position and the monitor switch is in the middle position.
2. Re-connect wire leads to each switch. Refer to pictorial
diagram.
3. Secure the latch hook (with two (2) mounting screws) to
oven cavity front flange.
4. Make sure that the monitor switch is operating properly
and check continuity of the monitor circuit. Refer to
chapter "Test Procedure" and "Adjustment procedure".
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to the
procedure of "CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL".
5. Remove the two (2) screws holding the latch hook to the
oven cavity front flange.
6. Remove the latch hook from the oven cavity front flange.
7. Disconnect the wire leads of each switch.
8. Remove each switch from the latch hook by pushing the
one (1) stopper tub holding each switch.
37
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
DOOR SENSING SWITCH, PRIMARY INTERLOCK SWITCH, AND MONITOR SWITCH ADJUSTMENT
the latched position. First check upper position of latch
hook, pushing and pulling upper portion of door toward
the oven face. Then check lower portion of the latch
hook, pushing and pulling lower portion of the door
toward the oven face. Both results (play in the door)
should be less than 0.5mm.
2. The door sensing switch, and primary interlock switch
interrupt the circuit before the door can be opened.
3. Monitor switch contacts close when door is opened.
4. The contact of door sensing switch and primary interlock
switch open within 1.2mm gap between right side of cavity
face plate and door when door is open.
5. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the control panel assembly, referring to the
procedure of "CONTROL PANEL ASSEMBLY ,
CONTROL UNIT AND KEY UNIT REMOVAL".
If the door sensing switch, primary interlock switch and
monitor switch do not operate properly due to a
misadjustment, the following adjustment should be made.
5. Loosen the two (2) screws holding latch hook to the oven
cavity front flange.
6. With door closed, adjust latch hook by moving it back
and forth, and up and down. In and out play of the door
allowed by the upper and lower position of the latch hook
should be less than 0.5mm. The vertical position of the
latch hook should be adjusted so that the door sensing
switch, secondary interlock switch are activated with the
door closed. The horizontal position of the latch hook
should be adjusted so that the monitor switch is activated
with the door closed.
7. Secure the screws with washers firmly.
8. Check all of the switches operation. If any switch has not
activated with the door closed, loosen screw and adjust
the latch hook position.
Latch
Hook
Latch
Heads
Door
Sensing
Switch
Door
Monitor
Switch
Primary
Interlock
Switch
After adjustment, check the following.
1. In and out play of door remains less than 0.5mm when in
Figure C-1. Latch Switch Adjustments
DOOR REPLACEMENT
DOOR ASSEMBLY REMOVAL
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity
by pushing the right and left tabs of the hood exhaust
louver. (Refer to the procedure of "HOOD EXHAUST
LOUVER REMOVAL".)
5. Insert a putty knife (thickness of about 0.5mm) into the
gap A between the door stopper and the choke cover
as shown in Figure C-3 to free engaging parts.
6. Lift up the door stopper.
7. Now, the door stopper is free from the door assembly.
8. Lift up the door assembly to release the upper and lower
door hinge pins from the upper and lower oven hinges.
9. Now, the door assembly is free.
4. Make sure upper and lower oven hinges are inserted into
the upper an lower door hinge pins.
5. Make sure the door is parallel with oven face lines (left
and upper side lines) and door latch heads pass through
latch holes correctly.
6. Re-install the door stopper to the door assembly.
7. Re-install the hood exhaust louver to the oven cavity
front face plate.
Note: After any service to the door;
(A) Make sure that door sensing switch and secondary
interlock switch are operating properly. (Refer to
chapter "Test Procedures".)
(B) An approved microwave survey meter should be
used to assure compliance with proper microwave
radiation emission limitation standards.
After any servicing, make sure of the following :
1. Door latch heads smoothly catch latch hook through
latch holes and that latch head goes through center of
latch hole.
2. Deviation of door alignment from horizontal line of cavity
face plate is to be less than 1.0mm.
3. Door is positioned with its face pressed toward cavity
face plate.
4. Re-install outer case and check for microwave leakage
around door with an approved microwave survey meter.
(Refer to Microwave Measurement Procedure.)
Note: When the individual parts are replaced, refer to
"Door Disassembly".
DOOR ASSEMBLY RE-INSTALL
1. On re-installing door, insert the lower oven hinge to lower
door hinge pin.
2. Insert the upper oven hinge to the upper door hinge pin.
3. Shut the door (close the contacts of interlock switches).
38
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
Note: The door on a microwave oven is designed to act
as an electronic seal preventing the leakage of
microwave energy from oven cavity during cook
cycle. This function does not require that door
be air-tight, moisture (condensation)-tight or
light-tight. Therefore, occasional appearance of
moisture, light or sensing of gentle warm air
movement around oven door is not abnormal
and do not of themselves indicate a leakage of
microwave energy from oven cavity.
Tab
Hood Exhaust Louver
Upper Door
Hige Pin
RE-INSTALL
Tab
Upper
Oven
Hige
Door assembly
Lower
Oven Hige
Latch
Heads
Lower Door
Hige Pin
Door Stopper
RE-INSTALL
Figure C-2. Door Replacement and adjustment
DOOR DISASSEMBLY
LATCH SPRING, LATCH HEAD AND DOOR PANEL
13.Release the latch spring from the tab of the latch head
and tab of the door frame.
14.Release the latch head from the door frame.
15.Now, the latch spring, latch head and door frame are free.
1. Disconnect the power supply cord and remove the oven
from wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal")
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove the hood exhaust louver from the oven cavity
by pushing the right and left tabs of the hood exhaust
louver. (Refer to the procedure of "HOOD EXHAUST
LOUVER REMOVAL".)
5. Remove door assembly, refer to "Door Replacement".
Replacement of door components are as follows:
6. Place door assembly on a soft cloth with latches facing
up.
Note: As the engaging part of choke cover and door frame
are provided at 15 places, do not force any particular
part.
A
Door Stopper
Choke Cover
Putty Knife
Door Frame
CHOKE COVER
7. Insert a putty knife (thickness of about 0.5mm) into the
gap A between the choke cover and door stopper and
between the choke cover and the door frame as shown
Figure C-3 to free engaging parts.
8. Pry the choke cover by inserting a putty knife in order
shown in Figure C-3.
9. Now choke cover is free from door panel and door frame.
Figure C-3. Door Disassembly
DOOR GLASS
16.Remove the glass stopper from the door frame by
releasing the tab of door frame.
17.At first, slide the door glass toward the glass stopper
side, and then slide it up. And release it from the right and
lower long tabs of the door frame.
18.Release the door glass from the upper long tab of the
door frame.
19.Release the door glass from the long tabs of the door
frame.
20.Now, the door glass is free.
DOOR FRAME
10.Remove six (6) screws holding the door panel and the
door handle to the door frame assembly.
11.Release the door frame assembly from the door panel.
NOTE: It is easier to release the engaging parts of the upper
or lower door hinge pin side at first.
12.Now, door frame assembly is free.
39
1
G
2
COM.
N.O.
3
40
RY1
4
CN-B
CN-C
CN-A
T1
YLW
BLK
ORG
RED
N.C.
5
PRIMARY
INTERLOCK
SWITCH
COM.
MONITOR
SWITCH
ORG
WHT
GRY
WHT
TURNTABLE
MOTOR
WHT
RED
BLK
WHT
WHT
BLK
RED
PPL
WHT
FAN
MOTOR
BLU
2 BLU
OVEN LAMP & SOCKET
WHT
RED
BLK
Power Supply
cord 120V 60Hz
Blue Marking
HOOD LAMPS
& SOCKETS
ORG
BLU
WHT
W W
H H
T T
MAGNETRON
R
E
D
YLW
BLK
RED
HIGH
VOLTAGE
RECTIFIER
HOOD FAN
THERMAL
CUT-OUT
POWER
TRANSFORMER
HIGH VOLTAGE
WIRE A
HIGH VOLTAGE
CAPACITOR
HIGH VOLTAGE COMPONENTS
WHT
RED
STIRRER MOTOR
Blue
Marking
GRN 1 GRN
5
Figure S-1. Pictorial Diagram
N.O.
COM.
WHT
WHT
RED
BLK
CT FUSE
BLK
ORG
CAVITY
THERMAL
CUT-OUT
RED
3 BLK
4
to Right Base Plate
RY2
COM.
BLK
ORG
GRY
RY1
COM.
RY2
N.O.
WHT
1 RED
2
5
4
3
6
ORG
PPL
RY1
N.O.
CN-A
7
8
9
1 WHT
3 YLW
2
BLK
1 BLU
BLK
WHT 2 WHT
3
N.O.
COM.
RY2
(POWER UNIT)
CN-B
1 WHT
BLU
RED 5 RED
YLW 4 YLW
WHT 3 WHT
BLK 2 BLK
HOOD FAN MOTOR
C
CN-E
CONTROL UNIT
CN-C
GRN
RED
DOOR SENSING SWITCH
COM.
E
N.O.
6
B
5 BLK
4
3 RED
2
F
1 RED
GRN
GRN
D
2 GRN
CN-E
2
2
1
1
to Chassis Support
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
6
A
A
B
C
H
6
D
E
F
G
H
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
1
2
4
3
5
6
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
Figure S-2. Power Unit Circuit
1
2
4
3
41
5
6
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
1
2
4
3
5
6
A
B
B
C
C
Figure S-3. LSI Unit Circuit
A
D
E
D
E
F
F
G
G
H
H
1
2
4
3
42
5
6
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
1
2
4
3
5
6
A
A
B
B
C
C
D
D
E
E
F
F
G
G
H
H
Figure S-5. Printed Wiring Board
1
2
4
3
43
5
6
PARTS LIST
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
Note: The parts marked “∆” may cause undue microwave exposure.
The parts marked “*” are used in voltage more than 250V.
REF. NO.
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
FH-DZB015MRY0
RC-QZA234WRE0
RMOTDA252WRZZ
RMOTDA258WRZZ
RTHM-A136WRZZ
RTRN-B081MRE0
RV-MZA324WRZZ
QSW-MA085WRE0
FFS-BA019/KIT
FACCDB011MRE0
QSOCLB006MRE0
FMOTEA402WRK0
RMOTEA346WRE0
RLMPTA086WRZZ
RTHM-A135WRZZ
FDTCTA201WRK0
High voltage rectifier assembly
High voltage capacitor
Turntable motor
Stirrer motor
Thermal cut-out N.O. 60oC (Hood Fan)
Power transformer
Magnetron
Pri. interlock and door sensing switches
Monitor switch (V-16G-2C25)/CT fuse (20A 250V AC) & Inst.
Power supply cord
Oven lamp socket
Hood fan motor
Fan motor
Oven lamp
Thermal cut-out 145oC (Cavity)
AH Sensor
17
18
18
18
18
19
20
21
21
21
22
23
24
25
26
27
28
29
LSTY-B021MRP0
PDIF-B052MRF0
PDIF-B045MRF0A
PDIF-B046MRF0A
FDIF-B016MRK0
GDAI-B064MRP0A
PCUSUB045MRP0
GCABUB142MRP0
GCABUB143MRP0
GCABUB144MRP0
TMAPCB081MRR0
FANGKB020MRY0
LANGQB062MRP0
PGLSPB004MRE0
PCOVPB115MRT0
PCUSUB040MRP0
PCUSGB028MRP0
PCUSUB047MRP0
Rear stay
Hood exhaust louver [GLMV169DB]
Hood exhaust louver [GLMV169DS]
Hood exhaust louver [GLMV169DQ]
Hood exhaust louver [PLMV169DC]
Right base plate
Cabinet cushion
Outer case cabinet [GLMV169DB/PLMV169DC]
Outer case cabinet [GLMV169DS]
Outer case cabinet [GLMV169DQ]
Schematic diagram
Hood lamp glass assembly
Hood lamp glass angle
Hood lamp glass
Base cover
Base cover cushion
Cushion
Mag cushion
30
31
31
31
31
32
32
32
33
34
35
CPWBFB099MRU0
HPNLCB194MRR0
HPNLCB196MRR0
HPNLCB195MRR0
FPNLCB484MRK0
FUNTKB415/KIT
FUNTKB417/KIT
FUNTKB416/KIT
LANGQB061MRP0
XEPSD30P10XS0
XEPSD30P08XS0
Control unit
Control panel sub. assembly [GLMV169DB]
Control panel sub, assembly [GLMV169DQ]
Control panel sub, assembly [GLMV169DS]
Control panel sub. assembly [PLMV169DC]
Key unit [GLMV169DB/PLMV169DC]
Key unit [GLMV169DQ]
Key unit [GLMV169DS]
Key fixing plate
Screw; 3mm x 10mm
Screw; 3mm x 10mm
Q'TY
ELECTRIC PARTS
*
*
∆
1
1
1
1
1
1
1
2
1
1
3
1
1
3
1
1
AL
AQ
AG
BF
BC
AE
AF
AP
AE
BE
AR
AE
AG
AU
CABINET PARTS
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
AF
AT
AT
AT
AT
AM
AA
BA
BC
BC
AB
AN
AG
AH
AY
AY
AY
1
1
1
1
1
1
1
1
1
1
3
BL
AZ
AZ
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
AH
AN
AN
BB
AN
AH
-AA
AG
AP
AC
AB
AD
AM
AA
AB
AD
AE
AL
CONTROL PANEL PARTS
AZ
AX
AX
AK
AB
AB
OVEN PARTS
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
FFTA-B005MRK0
FROLPB025MRK0
NTNT-A090WRE0
LANGKB010MRP0
FCOVPB016MRK0
FFAN-B010MRK0
*************
PPACGB014MRF0
PHOK-B024MRF0
LANGTB036MRP0
NFANPB001MRE0
LBSHC0037WRE0
PCOVPB065MRP0
PDUC-B095MRP0
PCUSUB039MRP0
PFILWB005MRP0
LANGTB046MRP0
LANGTB040MRP0
PDUC-B094MRF0
Exhaust damper assembly
Turntable support assembly
Turntable tray
Capacitor holder
Stirrer cover assembly
Stirrer fan assembly
Oven cavity (Not replaceable part)
Turntable motor packing
Latch hook
Unit mounting plate
Fan blade
Cord bushing
Oven lamp cover
Hood intake duct R
Hood intake duct cushion
Lamp filter
Chassis support left
Chassis support right
Hood duct
44
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
REF. NO.
55
56
57
58
59
60
61
62
PART NO.
LHLD-B012MRF0
LSTPPB031MRF0
PCOVPB076MRF0
PCOVPB077MRF0
PCOVPB078MRF0
PDUC-B098MRP0
LHLD-B016MRF0
LHLD-B017MRF0
Rack holder
Door stopper
Louver cover A
Louver cover B
Louver cover C
Magnetron air guide
Left rear holder
Right rear holder
DESCRIPTION
63
63
63
63
64
64
64
65
65
65
66
66
66
67
68
69
70
70
70
71
72
73
73
73
73
74
75
CDORFB366MRK0A
CDORFB361MRK0A
CDORFB362MRK0A
CDORFB363MRK0A
FDORFB083MRT0
FDORFB084MRT0
FDORFB085MRT0
FCOV-B267MRK0
FCOV-B268MRK0
FCOV-B269MRK0
PGLSPB072MRE0
PGLSPB073MRR0
PGLSPB074MRR0
LSTPPB030MRF0
LSTPPB032MRF0
MSPRTA046WRE0
GWAKPB187MRR0
GWAKPB188MRR0
GWAKPB189MRR0
FCOVHB005MRK0
PSHEPB024MRE0
FHNDPB015MRK0
JHNDPB049MRF0
JHNDPB050MRF0
JHNDPB051MRF0
XCPSD40P08000
XCPSD40P10000
Door assembly [PLMV169DC]
Door assembly [GLMV169DB]
Door assembly [GLMV169DS]
Door assembly [GLMV169DQ]
Door panel assembly [GLMV169DB/PLMV169DC]
Door panel assembly [GLMV169DS]
Door panel assembly [GLMV169DQ]
Door frame assembly [GLMV169DB] (not available in S/S)
Door frame assembly [GLMV169DS]
Door frame assembly [GLMV169DQ]
Front door glass [GLMV169DB/PLMV169DC]
Front door glass [GLMV169DS]
Front door glass [GLMV169DQ]
Latch head
Glass stopper
Latch spring
Door frame [GLMV169DB] (not available in S/S)
Door frame [GLMV169DS]
Door frame [GLMV169DQ]
Choke cover assembly
Sealer film
Door handle [PLMV169DC]
Door handle [GLMV169DB]
Door handle [GLMV169DS]
Door handle [GLMV169DQ]
Screw : 4mm x 8mm
Screw : 4mm x 12mm
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
CFZK-B131MRK0
LBSHC0040MRE0
LX-BZ0195WRE0
LX-MZB001MRE0
XBRSD50P60000
XOTSD40P12000
XTSSD50P35000
XWHSD50-16300
TINSEB385MRR0
TINSEB380MRR0
TINSKB047MRR0
TINSKB048MRR0
QW-QZB023MRE0
FW-VZB234MRE0
TCAUAB048MRR0
TCAUAB050MRR0
PFIL-B011MRE0
PFIL-B010MRE0
PCLICB003MRE0
UAMI-B009MRM0
QW-VZB010MRE0
Installation material assembly
Grommet
Toggle screw
Cord holder
Screw : 5mm x 60mm
Screw : 4mm x 12mm
Screw : 5mm x 35mm
Washer
Installation instruction
Operation manual
Top template
Wall template
High voltage wire A
Main harness
A
DHHS/GRD/caution label
Monitor caution label
Charcoal filter
Grease filter
Canoe clip
Rack
Sensor gnd wire
97
98
99
100
101
102
103
104
104
105
106
XOTSE40P12000
XBTSD40P08000
LX-CZA038WRE0
LX-CZ0052WRE0
LX-BZB012MRE0
XCBSD30P08000
LX-BZA041WRE0
LX-CZB024MRE0
LX-CZB025MRE0
LANGTB055MRP0
LANGTB100MRP0
Screw : 4mm x 12mm
Screw : 4mm x 8mm
Special screw
Special screw
Unit mounting screw
Screw : 3mm x 8mm
Special screw
Louver screw [GLMV169DS/GLMV169DQ]
Louver screw [PLMV169DC/GLMV169DB]
Chassis support
Chassis support gusset
Q'TY
2
1
1
1
1
1
1
1
AF
AC
AG
AG
AG
AC
AF
AF
DOOR PARTS
∆
∆
∆
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
4
2
AX
AX
AX
AX
AX
BD
BD
AQ
AQ
AC
AC
AB
AZ
AZ
AH
AF
AL
AL
AA
AA
MISCELLANEOUS
1
1
4
1
2
1
6
2
1
1
1
1
1
1
1
1
1
2
1
1
1
AM
AC
AC
AB
AC
AA
AA
AA
AB
AD
AC
AB
AD
AU
AA
AA
AH
AF
AA
AR
10
2
4
2
2
6
9
3
3
2
4
AA
AA
AA
AA
AD
AA
SCREWS,NUTS, WASHERS AND MISC.
45
AA
AA
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
2
1
4
3
6
5
OVEN AND CABINET PARTS
102
97
36
A
A
96
97
12
48
16
17
99
54
97
45
B
B
21
97
47
46
98
20
13
C
10
99
50
28
103
C
14
11
97
52
97
90
22
102
4
15
103
9
105
97
106
D
D
101
105
42
106
59
103
55
58
E
53
60
61
E
103
92
97
62
57
55
91
100
104
8
7
18
9
104
41
29
101
49
44
2
8
F
7-8
51
104
103
43
40
6
3
93
102
102
38
94
F
39
1
5
50
19
26
G
G
97
27
37
97
11
93
25
14
H
23
H
97
24
97
1
2
4
3
46
5
6
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
2
1
4
3
6
5
CONTROL PANEL PARTS
31
A
A
32
33
97
30
35
B
B
34
56
DOOR PARTS
72
C
C
74
64
63
71
74
68
66
70
D
D
75
65
E
E
67
MISCELLANEOUS
69
73
F
F
88
89
G
G
76
77
80
95
81
78
H
79
1
82
83
H
2
4
3
47
5
6
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
PACKING AND ACCESSORIES
TOP PAD
DOOR PROTECTOR
WRAP COVER
38
TURNTABLE TRAY
DOOR PAD
76
INSTALL MATERIAL ASSEMBLY
85
OPERATION MANUAL
87
WALL TEMPLATE
84
INSTALLATION INSTRUCTION
86
TOP TEMPLATE
93
95
RACK
RACK HOLDER
GREASE FILTER (x 2)
36
DAMPER ASSEMBLY
BOTTOM PAD
ACCESSORY HOLDER
Non-replaceable items
PACKING CASE
48
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
NOTES
49
GLMV169DB
GLMV169DQ
GLMV169DS
PLMV169DC
ELECTROLUX
COPYRIGHT © 2004 BY ELECTROLUX HOME PRODUCTS, INC.
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in retrieval systems, or transmitted in
any form or by any means, electronic,
mechanical, photocopying, recording, or
otherwise, without prior written permission of
the publisher.
50