Shark Stp-2310 Specifications

Model: STP
operating instruction
and parts manual
■ STP-2015
■ STP-2310
CH
D
AU
■ STP-3520
!
TELTUO RETAW TOH
ETNEILAC AUGA LED ADILAS
EDUAHC UAE'D EITROS
!
CIONE LA
ECT
NN TE
ATEN
CO IEN TES
ING
RN
ECT L
NN ICA E
CO
DIS ELECTR OR
BEF .
M
FRO PLY VICING
SUPSER
WA
OF
N!
NTIOR ON
ATI
ATTECOUPE
ENT E
LIM CTRIQUFAIRE .
ELENT DE ATION
AR
AVA REP
E
UN
L'A
DIS CORR ICA ANVICIO.
CTR SER
ELE DAR
DE
MO
DE
D' EM
PLO
MP
PU
F
ER
RN
BU
T
STA
MO TATO
ER OS AT
TH TERM MOST
ER
TH
I
S
IONE
CC ON
RU RACI
INST OPE
DE
NG
RATI IONS
OPE RUCT
INST
40°
ITE
WH
25° N
EE
GR
15°
OW
YELL
0°
RED
N
TE
IN
ED
D
FO
R
DO
IN
R
O
CO
US
E
LD
ING
WAT
RE
AD SO
ER
MIS DE
SIO L AG INLE
N
D'E UA FR T
AU
IA
FR
OID
For technical assistance or the SHARK dealer nearest you
visit our website at www.shark-pw.com
8.914-341.0 / 97-6153
CONTENTS
Pump Volume At Pump Head:
STP-2015 1.9 GPM
STP-2310 2.1 GPM
STP-3520 3.5 GPM
l Pump Pressure At Pump Head: STP-2015 1500 PSI
STP-2310 1000 PSI
STP-3520 2000 PSI
l Machine Voltage:
STP-2015 120V/1PH
STP-2310 120V/1Ph
STP-3520 230V/1Ph
l
Machine Dimensions: l
STP-2015
STP-2310
STP-3520
l
Total Machine Amperage: STP-2015 20 Amps
STP-2310 15 Amps
STP-3520 22 Amps
Shipping Weight:
STP-2015 330 Lbs.
STP-2310 330 Lbs.
STP-3520 340 Lbs.
l
Length = 39"
Length = 39"
Length = 39"
Width = 27"
Width = 27"
Width = 27"
Height = 44"
Height = 44"
Height = 44"
serial number:
DATE pURCHASED:
for sales and service, please contact:
Shark STP Manual • Form 8.914-341.0 / 97-6153 • Revised 6/07
MACHINE SPECIFICATIONS
Introduction............................................................... 4
STP Exploded View Parts List........................... 14-15
Important Safety Information................................. 4-5
Control Panel Exploded View and Parts List.......... 16
Installation............................................................ 5, 7
Hose & Spray Gun Assembly and Parts List.......... 17
Component Identification.......................................... 6
Downstream Injector Assembly and Parts List....... 18
Starting and Operating Instructions.......................... 7
VBA35 Unloader Exploded View and Parts List..... 19
How To Use The Detergent Injector.......................... 8
GE Pump Exploded View and Parts List........... 20-21
Preventative Maintenance........................................ 9
Troubleshooting................................................. 22-23
Maintenance and Service.................................... 9-11
Maintenance Schedule........................................... 24
STP Exploded View........................................... 12-13
Oil Change Record................................................. 24
Warranty
Shark STP Manual • Form 8.914-341.0 / 97-6153 • Revised 6/07
STP SERIES PRESSURE WASHER
INTRODUCTION
WarNiNg
Thank you for purchasing a STP.
This manual covers the operation and maintenance
of the STP Series pressure washers. All information in
this manual is based on the latest product information
available at the time of printing.
We reserve the right to make changes at any time without
incurring any obligation.
Owner/User Responsibility:
The owner and/or user must have an understanding of
the manufacturer’s operating instructions and warnings
before using this pressure washer. Warning information
should be emphasized and understood. If the operator
is not fluent in English, the manufacturer’s instructions
and warnings shall be read to and discussed with the
operator in the operator’s native language by the purchaser/owner, making sure that the operator comprehends its contents.
Owner and/or user must study and maintain for future
reference the manufacturers’ instructions.
This manual should be considered a permanent
part of the machine and should remain with it
if machine is resold.
When ordering parts, please specify model and serial number.
important safety
information
CAUTION
read operator’s
manual thoroughly
prior to use.
CAUTION: To reduce the risk of
injury, read operating instructions carefully before using.
1.Read the owner's manual
thoroughly. Failure to follow
instructions could cause malfunction of the machine and
result in death, serious bodily
injury and/or property damage.
2.All installations must comply with local codes. Contact your electrician, plumber, utility company or the
selling distributor for specific details.
To comply with National Electrical Code (NGPA 70)
and provide additional protection from risk of electric
shock, this hot water converter is equipped with a
UL approved ground fault circuit interrupter (GFCI)
power cord.
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
risk of fire.
do not use with
flammable liquids.
OPERATOR’S MANUAL
WARNING: Flammable liquids
can create fumes which can ignite causing property damage or
severe injury.
WARNING: Do not use gasoline,
crankcase drainings or oil containing gasoline, solvents or alcohol. Doing so will result in fire
and/or explosion.
WARNING: Do not spray flammable liquids. Operate
only where an open torch is permitted.
3.This fuel burning machine shall be installed only in
locations where combustible dusts and flammable
gases or vapors are not present.
4.In these oil burning models, use only kerosene, No.1
home heating fuel, or diesel fuel.
WARNING: Keep water spray,
wand and high pressure hose
away from electrical wiring or
fatal electric shock may result.
Read warning tag on electrical
cord.
5.To protect the operator from
keep water spray
away from
electrical shock, the machine
electrical wiring.
must be electrically grounded.
It is the responsibility of the
owner to connect this machine
to a UL grounded receptacle of proper voltage and
amperage ratings. Do not spray water on or near
electrical components. Do not touch machine with
wet hands or while standing in water. Always disconnect power before servicing.
WarNiNg
CAUTION: Spray gun kicks back — hold with both
hands.
6.Grip cleaning wand of attached pressure washer
securely with both hands before starting cleaner.
Failure to do this could result in injury from a whipping wand.
WARNING: High pressure stream
of fluid that this equipment can
produce can pierce the skin and
its underlying tissues, leading
to serious injury and possible
amputation.
high pressure
7. High pressure developed by the
spray can pierce
attached pressure washer can
skin and tissues.
cause bodily injury or damage.
Use caution when operating. Do not point the spray
gun at anyone or at any part of the body. This machine is to be used only by qualified operators.
8.Never make adjustments on machine while it is in
operation.
WarNiNg
STP SERIES PRESSURE WASHER
WarNiNg
protective
eyewear and clothing must
be worn.
WarNiNg
risk of
asphyxiation.
use only in a well
ventilated area.
WARNING: High pressure spray
can cause paint chips or other
particles to become airborne and
fly at high speeds.
9. Eye safety devices must be
worn when using this equipment.
WARNING: Risk of asphyxiation
— Use this product only in a well
ventilated area.
10. When the machine is working, do not cover or place in a
closed space where ventilation
is insufficient.
WARNING: Risk of fire. Do not
add fuel when the machine is
operating or still hot.
11. Machines with a spray gun
should not be operated with
the spray gun in the off position
risk of fire.
for extended periods of time
do not add fuel
when operating
as this may cause damage
machine.
to the pump. Check to make
sure burner shuts off when spray gun trigger is
closed.
12.Protect from freezing.
13.To prevent a serious injury, make certain quick
coupler on discharge hose has locked before using
pressure washer.
14.Do not allow acids, caustic or abrasive fluids to pass
through the pump.
15.Inlet water must be cold and clean fresh water.
16.Do not allow CHILDREN to operate the pressure
washer at any time. THIS MACHINE MUST BE
ATTENDED DURING OPERATION.
17.The best insurance against an accident is precaution, and knowledge of the machine.
18.Do not operate this product when fatigued or under
the influence of alcohol or drugs. Keep operating
area clear of all persons.
19. We will not be liable for any changes made to our
standard machines, or any components not purchased from us.
20.Do not overreach or stand on unstable support. Keep
good footing and balance at all times.
21. Follow the maintenance instructions specified in the
manual.
WarNiNg
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
OPERATOR’S MANUAL
22. When making repairs disconnect from electrical
source.
23.Turn burner off and open spray gun to allow water to
flow and cool coil to 100°F before turning machine
off.
24. Before disconnecting high pressure hose from
hot water outlet, turn off burner to allow water to cool
to 100°F, then turn off pump motor and water supply and operate spray gun to relieve back pressure
in hose. This will prevent coil damage from thermal
expansion.
Caution: This machine produces hot water and
must have insulated components attached to protect
the operator.
INSTALLATION
Place machine in a convenient location providing ample
support, draining and room for maintenance.
This machine is intended for indoor use. Machine
must be stored indoors when not in use.
Location:
The location should protect the machine from damaging environmental conditions, such as wind, rain, and
freezing.
1.This machine should be run on a level surface where
it is not readily influenced by outside sources such
as strong winds, freezing temperatures, rain, etc.
It should be located to allow accessibility for refilling of fuel, adjustments and maintenance. Normal
precautions should be taken by the operator of the
machine to prevent moisture from reaching the
electrical controls.
2.It is recommended that a partition be made between
the wash area and the machine to prevent water
spray from coming in contact with the machine. Excess moisture reaching any electric components or
electrical controls will reduce machine life and may
cause electrical shorts.
3.During installation of the machine, beware of poorly
ventilated locations or areas where exhaust fans may
cause an insufficient supply of oxygen. Sufficient
combustion can only be obtained when there is a
sufficient supply of oxygen available for the amount
of fuel being burned. If it is necessary to install a
machine in a poorly ventilated area, outside fresh
air may have to be piped to the burner and a fan
installed to bring air into the machine.
Avoid small locations or areas near exhaust fans.
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
component identification
CAUTION HOT WATER:
Must use insulated
spray gun and wand.
Nozzle
ON-OFF
Switch
Adjustable
Thermostat
Discharge Nipple
Wand Holder
Fresh Water
Faucet
(not included)
Downstream
Detergent Injector
GFCI
Burner Chamber
Unloader
Pump
Burner Motor
Garden Hose
(not included)
Detergent Bucket
(not included)
Nozzle
Coupler
Detergent
Suction Hose
Trigger
Insulated
Spray Gun
Variable Pressure
Insulated Wand
Control
Handle
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
High Pressure
Outlet Hose
STP SERIES PRESSURE WASHER
Electrical:
This machine, when installed, must be electrically
grounded in accordance to local codes. Check for proper
power supply using a volt meter.
Placement:
Do not locate near any combustible material. Keep all
flammable material at least 20 feet away.
Allow enough space for servicing the machine.
Local code will require certain distances from floor and
walls. (Two feet away from walls should be adequate.)
Water Source:
The water source for the pressure washer should be
supplied by a minimum 5/8" I.D. garden hose with a city
water pressure of not less than 30 PSI. If the water supply is inadequate, or if the garden hose is kinked, the
attached pressure washer will run very rough and the
burner will not fire.
Connection:
Connect the wand, nozzle, hose and spray gun (where
applicable). On pipe thread connections, use teflon tape
to avoid water leaks. (See Component Identification).
OPERATOR’S MANUAL
6.Securely attach the desired high pressure nozzle
into wand coupler as described in steps 4 and 5.
7.Connect the power cord into the proper electrical
outlet, then push in the GFCI reset button (Refer to
serial plate for information.)
8.Grip spray gun handle securely and pull trigger. Then
turn variable pressure control handle counterclockwise.
9.Turn switch to pump position. When a steady stream
of water flows from the spray gun and wand, the
machine is ready for cold water cleaning by turning
the variable pressure control handle clockwise to
raise the pressure.
10. For hot water washing, turn the switch to the burner
position. (The burner will light automatically when
the trigger on the spray gun is pulled.)
Brass Soap
Nozzle
Variable Pressure
Wand (VP)
High
Pressure
Nozzle
Variable Pressure
Control Handle
Trigger
Venting:
Adding exhaust vent pipe to your oil fired burner is not
recommended because restricted air flow causes carbon buildup, which affects the operation, and increases
maintenance on the coil. If a stack must be used, refrain
form using 90° bends. If the pipe can not go straight up
then use only 45° bends and go to the next size pipe. The
overall pipe length must not exceed 6 feet in length.
Starting and operating
instructions
To Start:
1.STOP! Read operator's manual
before operating. Failure to read
operation and warning instructions may result in personal
injury or property damage.
2. Connect water supply hose and
turn on water.
read operator’s
manual thoroughly 3.Check fuel tank and pump oil
prior to use.
levels.
4.Connect high pressure hose to discharge nipple by
sliding quick coupler collar back. (If detergent is to
be applied, insert a detergent injector as shown in
Component Identification).
5.Insert quick coupler onto discharge nipple and secure by pushing quick coupler collar forward.
CAUTION
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
Selection of high or low pressure is accompanied by
turning the handle. Note: High pressure nozzle must
be inserted at end of wand to obtain high pressure. To
apply soap read operator's manual.
To Stop:
1. If using the detergent injector, place the suction line
in a bucket of water allowing detergent to be flushed
from system.
2.Turn STP burner switch off and continue spraying
water, allowing the water to cool.
3.After water has cooled to less than 100°F, turn the
attached pressure washer off.
4.Turn garden hose water off. Open the spray gun to
relieve remaining pressure.
5.Protect from freezing.
STP SERIES PRESSURE WASHER
HOW TO USE THE
DETERGENT INJECTOR
WARNING: Some detergents may
be harmful if inhaled or ingested
causing severe nausea, fainting
or poisoning. The harmful elements may cause property damage or severe injury.
some detergents
The machine can siphon and mix
may be harmful
detergents with the use of Shark's
if inhaled or
ingested.
detergent injector kit.
1. Pull injector quick coupler collar back and secure on
discharge nipple. Injector valve body arrow should
point in direction of flow.
2. Connect high pressure hose to injector nipple securing quick coupler.
WarNiNg
OPERATOR’S MANUAL
3.Start machine as outlined in Operating Instructions.
4.Place detergent pick-up tube into container of detergent solution.
5.Turn pressure control handle counterclockwise on
the variable pressure wand. This lowers the pressure
by directing the water flow through the soap nozzle
and allows the detergent injector to siphon soap.
6.Open trigger spray gun. Water detergent ratio is
approximately 15 to 1.
7. When you finish washing, rinse by simply turning the
variable pressure wand control handle clockwise to
increase pressure.
NOTE: The detergent injector will not siphon with
water flowing through the high pressure nozzle at
the end of the wand.
8. For clean up, place detergent pick-up tube into
container of clear water and follow steps 5 and 8
to prevent detergent deposits from damaging the
injector.
Rupture Disk
Discharge Nipple
Detergent Injector
Collar
Detergent
Pickup Tube
Brass Soap
Nozzle
Quick Coupler
Spray Gun
Trigger
Variable Pressure
Wand (VP)
High Pressure
Hose
Nozzle Quick
Coupler
Variable Pressure
Control Handle
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
STP SERIES PRESSURE WASHER
Preventative
maintenance
1.Use clean fuel - kerosene, No. 1 home hearing fuel
or diesel fuel. Clean or replace fuel filter every 100
hours of operation. Avoid water contaminated fuel as
it will seize up the fuel pump. De-soot coils monthly.
Use an additive if diesel is being used.
2.Check to see that the attached pressure washer
water pump is properly lubricated.
3. Follow Winterizing Procedures to prevent freeze
damage to pump coils.
4.Always neutralize and flush detergent from system
after use.
5.If water is known to be high in mineral content, use
a water softener in your water system or de-scale
as needed.
6.Do not allow acidic, caustic or abrasive fluids to be
pumped through system.
7.Always use high grade quality cleaning products.
8.Never run pump dry for extended periods of time.
9.If machine is operated with smoking or eye burning
exhaust, coils will soot up, not letting water reach
maximum operating temperature. (See section on
Air Adjustments.)
10.Never allow water to be sprayed on or near engine
or burner assembly or any electrical component.
11.Periodically delime coils per instructions.
It is advisable, periodically, to visually inspect the burner.
Check air inlet to make sure it is not clogged or blocked.
Wipe off any oil spills and keep this equipment clean
and dry.
The areas around the Shark washer should be kept
clean and free of combustible materials, gasoline and
other flammable vapors and liquids.
The flow of combustion and ventilating air to the burner
must not be blocked or obstructed in any manner.
MAINTENANCE AND SERVICE
Unloader Valves:
Unloader valves are preset and tested at the factory
before shipping. Occasional adjustment of the unloader
may be necessary to maintain correct pressure. Call
your local dealer for assistance.
Winterizing Procedure:
Damage due to freezing is not covered by warranty.
Adhere to the following cold weather procedures
whenever washer must be stored or operated outdoors
under freezing conditions. During winter months, when
temperatures drop below 32°F, protecting your maShark STP • 8.914-341.0 / 97-6153 • REV. 6/07
OPERATOR’S MANUAL
chine against freezing is necessary. Store machine in
a heated room. If this is not possible then mix a 50/50
solution of anti-freeze/water into a 5 gallon bucket. Place
a short section of garden hose into bucket and connect
it to machine. Elevate bucket and turn pump on to siphon
anti-freeze through machine. If compressed air is available, an air fitting can be screwed into the inlet connector
and, by injecting compressed air, all water will be blown
out of system.
High Limit Hot Water Thermostat:
For safety, each machine is equipped with a high limit
control switch. In the event that the temperature of the
water should exceed its operating temperature, the
high limit control will turn the burner off until the water
cools.
Pumps:
Use only SAE 30W non-detergent oil. Change oil after
the first 50 hours of use. Thereafter, change the oil every
three months or at 500 hour intervals. Oil level should be
checked by using the dipstick found on top of the pump
or the red dot visible through the oil gauge window. Oil
should be maintained at that level.
Cleaning of Coils:
In alkaline water areas, lime deposits can accumulate
rapidly inside the coil pipes. This growth is increased by
the extreme heat build up in the coil. The best prevention for liming conditions is to use high quality cleaning
detergents. In areas where alkaline water is an extreme
problem, periodic use of Shark Deliming Powder (part
#9-028008) will remove lime and other deposits before
coil becomes plugged. (See Deliming Instructions for
use of Shark Deliming Powder.)
Deliming Coils:
Periodic flushing of coils is recommended.
1. Fill a container or optional float tank with 4 gallons
of water, then add 1 lb. of deliming powder. Mix
thoroughly.
2.Remove wand assembly from spray gun and put
spray gun into container. Secure the trigger on the
spray gun into the open position.
3.Attach a short section (3-5 ft.) of garden hose to machine to siphon solution from an elevated container.
Turn pump switch on, allowing solution to be pumped
through coils back into the container. Solution should
be allowed to circulate 2-4 hours.
4.After circulating solution flush entire system with
fresh water. Reinstall wand assembly to spray gun.
Removal of Soot in Heating Coil:
In the heating process, fuel residue in the form of soot
deposits may develop between the heating coil pipe
10
STP SERIES PRESSURE WASHER
and block air flow which will affect burner combustion.
When soot has been detected on visual observation, the
soot on the coil must be washed off after coil has been
removed using the following steps:
1.Remove the tank head assembly by lifting the tank
head off.
2.Remove the two pipe nipples and associated fittings.
3.Lift the coil out of the outer wrap.
OPERATOR’S MANUAL
Burner Nozzle:
Keep the tip free of surface deposits by wiping it with a
clean, solvent-saturated cloth, being careful not to plug
or enlarge the nozzle. For maximum efficiency, replace
the nozzle each season.
Fuel Control System:
If pressure from pump or thermal expansion should
exceed safe limits, the rupture disk will burst, allowing
high pressure to be discharged through hose to ground.
When the disk ruptures, it will need to be replaced.
The STP utilizes a fuel solenoid valve located on the fuel
pump to control flow of fuel to the combustion chamber.
This solenoid is activated by a pressure switch located
on the unloader valve. When an operator releases the
trigger on the spray gun, the pressure drops, allowing
the pressure switch to activate the fuel solenoid. The
solenoid then closes, shutting off the supply of fuel to the
combustion chamber. Controlling the flow of fuel in this
way gives an instantaneous burn or no burn situation,
thereby eliminating high and low water temperatures, and
combustion smoke normally associated with machines
incorporating a spray gun. Periodic inspection is recommended to insure that the fuel solenoid valve functions
properly. This can be done by operating the machine and
checking to see that when the trigger on the spray gun is
in the off position, the burner is not firing.
Fuel:
Fuel Pressure Adjustment:
Use clean fuel oil that is not contaminated with water
and debris. Replace fuel filter and drain tank every 100
hours of operation. Use Kerosene No. 1 or No. 2 Heating
Fuel (ASTM D306) or diesel only. NEVER use gasoline
in your burner tank. Gasoline is more combustible than
fuel oil and could result in a serious explosion. NEVER
use crankcase or waste oil in your burner. Fuel unit
malfunction could result from contamination.
To adjust fuel pressure, turn the adjusting screw with a
screwdriver (located on the fuel pump) clockwise to
increase, counterclockwise to decrease. Do not exceed
200 PSI.
CAUTION: the coil weighs about 80 lbs. Use proper
lifting techniques.
4. Clean, repair and replace the coil by reversing the
above steps.
Coil Reinstallation
Reinstall by reversing the above steps 4 through 1.
Rupture Disk
Ignition Circuit:
Periodically inspect wires, spring contact and electrodes for condition, security and proper spacing. For
transformer test (CAUTION 10,000 VOLTS) use defect
free insulated screwdriver and keep fingers off blade!
Lay blade across one contact: OK if arc will span 1/2"
between end of blade and other contact (see following
illustration).
Electrode Setting: Beckett
5/32" Gap
Electrode
7/16"
Nozzle
1/16"
Top View
Side View
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
Air Adjustment
Machines are preset and performance tested at the
factory — elevation 100' above sea level. A one time
correction for your location will pay off in economy,
performance and extended service life. If a smoky or
eye-burning exhaust is being emitted from the stack,
two things should be checked.
First, check the fuel to be certain that kerosene or No.
1 home heating fuel is being used.
Next, check the air adjustment on the burner. An oily,
black, smoky fire indicates a lack of air and the air band
should be moved to allow the air to flow through the
burner. Sharp, eye-burning fumes indicate too much
air flowing through the combustion chamber. The air
band should be moved to allow less air to flow through
the burner.
To adjust: Start the machine and turn burner ON.
Loosen two locking screws found in the air shutter
openings (refer to illustration) and close air shutter until
black smoke appears from burner exhaust vent. Note
air band position. Next slowly open the air shutter until
white smoke just starts to appear. Turn air shutter halfway back to the black smoke position previously noted.
Tighten locking screws.
STP SERIES PRESSURE WASHER
If the desired position cannot be obtained using only the
air shutter, lock the air shutter in as close a position as
can be obtained, then repeat the above procedure on
the air band setting.
FUEL AIR ADJUSTMENT
Air Shutter
Locking Screw
Air Shutter
Air Band
Air Shutter
Locking Screw
Air Band
Locking Screw
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
OPERATOR’S MANUAL
11
12
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
STP SERIES
EXPLODED VIEW left side
42
47
(Reversed View
of Label)
46
43
(Reversed
View of Label)
82
41
36
58
35
16
49
44
40
48
19
45
85
44
84
37
51
39
42
50
86
38
14
54
80
53
31
76
52
56
81
81
55
77
78 79
80
81
61
57
For
Detail See
Control
Panel
Illus.
60
62
62
64
25
65
63
10
32
83
25
11
71
59
72
68
67
To Fuel
Tank
3
83
11
66
74
To Fuel
Tank
2
3
1
1
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
2
69
73
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
STP SERIES
EXPLODED VIEW right side
33
27
28,29
21
26
25
30
20
18
24
23
22
Enlarged
View
Overload
Button
17
To
Burner
To Fuel
Filter
MoT
or
DE Pu
PO SH ov
SIT To er
IVO re lo
DE Se ad
RE T
PO
SIC
ION
70
15
13
11
12
11
9
8
7
6
7
5
75
75
3
2
1
34
4
1
4
3
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
2
13
14
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
STP Series
exploded view parts list
1
90-20041Collar, 5/8" Bore Shaft qty
4
2
4-0307
Wheel & Tire Assy, 6" Steel Rim
w/Tube
4
3
90-4005
Washer, 5/8", Flat, SAE
4
95-07104723Axle, Rod 5/8" x 27.80" L2
52-0115090Tank, Fuel 6 Gallon Blank
1
qty
27
6-0104Cord, Service, SOWA, 12/3
(201507D, 231007D)2.75 ft.
6-0108Cord, Service, SEO, 10/3 (352007D)
3.66 ft.
28
6-05152Strain Relief, Small (201507D,
231007D)
4
itempart no. description
itempart no. description
1
62-01167Cap, Fuel Tank, Plastic H60-AV 1
6-051595Strain Relief, STRT LQ TITE (352007A)
1
72-010061
29
6-05181ALocknut, 1/2" (201507D, 231007D)1
6-05181BLocknut, 3/4" 8465 (352007A)
Bushing, Rubber, Nitrile2
82-10866
Hose Barb, 1/4" Barb x 3/8" Barb,
Double
1
92-30057
Valve, 1/4" Shut-Off
1
102-1085
Hose Barb, 1/4" Barb x 1/4" ML
1
Pipe
112-9040Clamp, Hose, UNI .46 - .54
4
12
4-02100000 Hose, 1/4" Push-On, Fuel Line
11"
13
4-02100000 Hose, 1/4" Push-On, Fuel Line 7"
14
90-20012Nut, Whiz Loc, 5/16" Flange
4
152-10942Swivel, 1/2" MP x 3/4" GHF
w/Strainer (Legacy)
1
162-00681
1
Bushing, 1/2" x 3/8" Steel
1
30
5-3329Unloader, VBA 35
6.6 @ 3500
1
31
9.800-018.0Label, Tipover Hazard
1
32
9.800-049.0Label, Cleaning Solution
1
33
4-02047725 Hose, 3/8" x 25", 2 Wire,
Pressure Loop
1
34
1
10-020110Label, Use Only Kerosene
35
95-07101226Block, Discharge, 1/2" x 1/2",
Brass
1
362-3409Disk, Rupture Assy, 7000 PSI
1
372-1108
Hose Barb, 1/2" Barb x 3/8" MPT, Push-On
1
38
4-02110000 Hose, 1/2" Push-On2.5 ft.
172-0053Elbow, 1/2 JIC 3/8, 90°
P/N - TF 5405-8
1
392-2007Nipple, 3/8" x 3/8" NPT ST Male 1
182-300812Pump Protector, 1/4" 145° 1
402-1019Elbow, 3/8" Female
1
192-000891Nipple, 1/2" x 2-1/2", Galvanized
1
SCH 80
41
10-09004Label, Hot Water Outlet
1
42
11-013Label, Shark Logo Die Cut2
20
90-1016
Bolt, 3/8" x 1", NC HH
4
43
95-07102253Wrap, Outer Coil, Red
21
90-4002
Washer, 3/8" SAE, Flat
4
22
5-1413Pump, Shark SE 2020S (231007D, 201507D)
1
44
90-19710Screw, 1/4" x 3/4" HH NC,
Whiz Loc
4
45
90-2022Nut, Cage, 1/4" x 16 Gauge
4
46
95-07102310Coil, Assembly
1
47
11-1043Label, Warning, Text
1
5-1405Pump, Shark SE 3525F (352007A)1
23
6-021720Switch, Pressure, N/O, 1/4" NPT
SS
1
24
5-1004MMotor, 1.5 HP 115V 1725 RPM
(231007D)
1
5-1073Motor, 2HP 1PH 115V 1725 RPM
(201507D)
1
1
48
10-02025ALabel, Hot/Caliete w/Arrows
Warning
1
49
95-07290029Tank Head Assy,
16" DIA x 8" Stack
1
5-1053Motor, 5HP 1PH 230V 3450 RPM
(352007A)
1
50
7-014862Insulation, Tank Head,
16" OD x 8" ID
1
51
4
25
90-4001
12
522-00601Elbow, 1/2" JIC x 3/8" Fem, 90° 1
26
90-2001Nut, 5/16" ESNA, NC
4
53
95-07290053Retainer, Burner Insulation
1
54
90-19960Screw, 3/8" x 1-1/4" Whiz Loc
4
Washer, 5/16" Flat, SAE Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
90-50045Clip, Retaining U-Type
STP SERIES PRESSURE WASHER
15
OPERATOR’S MANUAL
STP Series
exploded view parts list (continued)
itempart no. description
qty
itempart no. description
55
7-01482Insulation, Tank Bottom,
1" Blanket
79
90-100472
1
80
90-2000Nut, 1/4" ESNA
4
56
1
81
90-4000
12
1
95-07104955Assembly, Frame, MS
572-0006Nipple, 3/8" x 3/8" Hex, Steel
Bolt, Carriage
qty
Washer, 1/4"
4
58
4-05088Thermostat, Adjustable, 302°F 1
82
7-01487Insulation, Blanket, 18" x 52", Fiberglass
1
59
90-2020Nut, Cage, 3/8" x 12 Gauge
83
4
60
7-00028
Burner, Beckett, 230V AFG
352007A)
7-00009
Burner, AFG, 120V, F4 Cone
(201507D, 231007D)
1
61
7-0101Nozzle, Burner, 1.75 B 90°
(352007A)
1
1
7-01244Nozzle, Oil, HOL 1.00 A, 90° (201507D, 231007D)
1
62
90-20040Nut, 3/8" Flange, Whiz Loc, NC 4
63
6-01011Cord, Service, SEO, 16/4,
Coleman
64"
64
6-0516Strain Relief, 1/2" Metal,
Two Screw
1
652-0013451Nipple, 1/4" x 3", Black Pipe
1
662-99050
Filter, Parker Fuel/Oil/H2O
(10 Micron), Generic
1
672-1089
Hose Barb, 1/4" Barb x 1/4" Pipe,
90°
1
68
10-09003Label, Cold Water Inlet
69
10-08017Label, Intended for Outdoor Use1
1
70
10-99078Label, Motor Overload Reset,
Lexan
1
712-01403
1
Bushing, Snap
72
6-01062GFCI, 120V 15A, w/36'
12-3 Cord (231007D)
1
6-01060GFCI, 120V 20A, w/36'
12-3 Cord (201507D)
1
6-01059GFCI, 240V 1PH 30A, w/36'
10-3 Cord (352007A)
1
73
1
10-08018Label, Warning, Service Cord
74
10-9999Label, Clear Lexan,
2-1/4" x 4-1/2"
1
75
6-05134Cable, TY, 48"2
76
95-07104827Lever, Brake
1
77
95-07104828Bracket, Brake Pad
1
78
95-07104829Linkage, Brake 1
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
90-1006
Bolt, 5/16" x 3/4" NC
8
842-00742Adapter, 1/2" x 1/2" Pipe
1
852-00575Elbow, 3/8" 45°
1
86
1
95-07104506Retainer Ring, Insulation
16
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
CONTROL PANEL
2
Exploded View
4
1
5
3
7
2
5
1
17
6
10
20
8
7
9
18
To
Thermostat
11
19
16
14
13
15
To Burner Motor
13
12
To Pressure Switch
To Motor
To Power Source
itempart no. description
qty
1
4-05088Thermostat, Adjustable, 302°F 1
2
6-020201Switch, 3 PS, 115V-230V, 1PH 1
3
95-07104957Cover, Electric Box
1
4
11-0319Label, Electric Box
1
5
90-1991Screw, 10/32" x 1/2" BHSOC
Blk
8
itempart no. description
qty
12
6-05152Strain Relief, STRT, LQ TITE Small (201507D, 231007D)2
6-0522Strain Relief, 12/4 Alum. (352007A)2
13
6-05152Strain Relief, STRT LQ TITE2
14
6-01270Conduit, Corr, Tubing, 1/4"2 ft.
6
6-05181ALocknut, 1/2"2
152-01403
Bushing, Snap, 5/8"
1
7
90-2018Nut, Cage, 10/32" x 16 Gauge 8
16
11-0317Label, Control Panel
1
17
90-017Nut, 10/32" Keps
4
8See Page 17Nozzle
4
92-0103Grommet, Rubber,
Nozzle Holder
18
90-1994Screw, 10/32" x 1-1/4" 1
4
19
11-1042Label, Ground
1
10
1
20
95-07104959Panel, Control
1
95-07104956Box, Electric
11
6-05181ALocknut, 1/2" (201507D,
231007D)2
90-19711
▲ Screw, 1/4" x 1/2" HH, NC, Whiz Loc
4
▲ Nut, 1/4" Flange
6-05181Locknut, 1/2" Conduit (352007A)2
90-200012
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
▲ Not Shown
4
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
17
HOSE AND SPRAY GUN ASSEMBLY
1
8
2
7
3
4
6
5
itempart no. description
12-2002Coupler, 3/8" Female
qty
qty
1
7
4-12804000Nozzle, SAQMEG 0004, Red
(231007D)
2
8.739-148.0 Hose, 3/8" x 50', 1 Wire, Blue,
Tuff-Flex
1
4-12804015Nozzle, SAQMEG 1504, Yellow
(231007D)
1
3
1
2-0121
▲ Quick Coupler O-Ring LG
4-01246Spray Gun, Shutoff, AP 1000
1
itempart no. description
4
4-0111341A Wand, VP Zinc 1/4" w/Coupler, w/Soap Nozzle 1
83-SSVPKIT ▲ AL Wand Repair Kit,
Stainless Seat
1
5
1
4-06540
Brass Soap Nozzle Only, 1/8"
62-2001Coupler, 1/4" Male
2-0119
▲ Quick Coupler O-Ring Sm
7
4-12803000Nozzle SAQMEG 0003, Red
(201507D)
1
4-12804025Nozzle, SAQMEG 2504, Green
(231007D)
1
4-12804040Nozzle, SAQMEG 4004, White
(231007D)
1
4-12805000Nozzle, SAQMEG 0005, Red
(352007A)
1
4-12805015Nozzle, SAQMEG 1505 Yellow
(352007A)
1
1
4-12805025Nozzle, SAQMEG 2505, Green
(352007A)
1
1
4-12805040Nozzle, SAQMEG 4005, White
(352007A)
1
8
4-011184Detergent Injector Assy,
3-5 GPM, 0.83 (352007A)
1
4-12803015Nozzle, SAQMEG 1503, Yellow
(201507D)
1
4-12803025Nozzle SAQMEG 2503, Green
(201507D)
1
4-12803040Nozzle, SAQMEG 4003, White
(201507D)
1
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
1
4-011183Detergent Injector Assy, 2-3 GPM, 0.70" (201507D, 231007D)
1
▲ Not Shown
18
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
DOWNSTREAM INJECTOR ASSEMBLY
1
3
4
2
itempart no. description
qty
1
3-12021Injector, Detergent, Non-Adjust #3 (352007A)
1
3-1202Injector, Detergent, Non-Adjust #2 (201507D, 231007D)
1
22-9040Clamp, Hose, UNI .46 - .542
3
4-02080000Tube, 1/4" x 1/2", Clear Vinyl 6 ft.
42-1904Strainer, 1/4" Hose Barb
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
1
STP SERIES PRESSURE WASHER
19
OPERATOR’S MANUAL
Unloader exploded view and parts list
#5-3329 VBA35
ITEM Part # description
Kit qty
ITEM Part # description Kit qty
1
70-020444 Body Valve
70-020452 Body Valve
1
1
16
70-110207Poppet
17
70-140802Seal Washer 3/82
2
70-060141O-RingA, C
1
18
70-180004 Hollow Bolt, 3/8
1
3
70-150316SeatC
1
19
70-180008 Hollow Bolt 1/2
1
4
70-450401 Ball, Sub-assyC
1
20
70-140803Seal Washer 1/22
5
70-060114O-RingA
1
21
70-120212PlateC
1
6
70-010111Guide Bushing
1
22
70-090037SpringC
1
7
70-000919Teflon RingA
1
23
70-180304Set Screw
1
8
70-060170O-RingA2
24
70-030209Nut
1
9
70-060162O-RingA
1
25
70-090520 Brass Handle
1
10
70-140734Connector
1
11
70-000918Teflon RingA
1
Kit A 70-262813 O-Ring Repair Kit
12
70-120611StemC
1
Kit B 70-262814Outlet Kit
13
70-140702Connector, Female
1
Kit C 70-262815Stem Repair Kit
14
70-060119O-RingA, B
1
15
70-090004Spring
1
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
B
B
1
20
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
GE SEries Pump Exploded View and Parts List
5-1901 GE 2020F, 5-1902 GE 2020S, 5-1903 GE 2825F
5-1904 GE 2825S, 5-1905 GE 3525F
TORQUE SPECS
Item #
Ft. -lbs.
14
65
17
18
25
7.6
36
8
38
7
47
13
item Part no. Description QTY
item Part no. Description QTY
1
70-020292Crankcase 1
16
70-160121
2*
70-000105Plunger Oil Seal
3
17
70-180118Manifold Stud Bolt
8
3*
70-060181O-Ring Ø 1.78 x 28.30
3
18
70-140001
8
4*
70-120131Pressure Ring 15mm
3
19
70-060306Copper Washer 3/8
70-120132Pressure Ring 18mm
3
20
70-160117
Brass Plug G1/4
Washer
1
1
Brass Plug G3/82
5*
70-000207
"V" Seal, dia 15mm
6
25
70-180112Screw
70-000208
"V" Seal, dia 18mm
6
26
70-020318
Bearing Cover 2
12
6*
70-030048Support Ring 15mm
6
27
70-020502
Bearing Seal
70-030050Support Ring 18mm
6
28
70-150003Snap Ring
7*
70-030049Intermed Ring 15mm
3
29
70-021300
1
1
Ball Bearing2
70-030051
intermed Ring 18mm
3
30
70-000600Crankshaft (2020F)
1
8*
70-160120
Brass Plug G1/2
1
70-000601Crankshaft (2020S)
1
9
70-060307Copper Washer 1/2"
1
70-000602Crankshaft (2825F)
1
10
70-160228Manifold Housing
1
70-000603Crankshaft (2825S)
1
11
70-060155O-Ring Ø1.78 x 15.54
6
70-000604Crankshaft (3525F)
1
12*See Kit BelowValve Assembly
6
31
70-160012Oil Dipstick
1
13*
70-060122O-Ring Ø2.62 x 18.77
6
32
70-060183O-Ring Ø3.53 x 55.56
1
14
70-160147
6
33
70-020011Needle Bearing
1
15
70-060308Copper Washer 1/4
1
34
70-050095Motor Flange 56C
1
Valve Plug
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
STP SERIES PRESSURE WASHER
21
OPERATOR’S MANUAL
GE SEries Pump Exploded View and Parts List (Cont)
5-1901 GE 2020F, 5-1902 GE 2020S, 5-1903 GE 2825F
5-1904 GE 2825S, 5-1905 GE 3525F
item Part no. Description QTY
35
70-140002 Washer
4
4
36
70-180126
37
70-000104Crankshaft Seal
Flange Screw
1
38*
70-030211Plunger Nut
3
39* 70-120023Plunger 15mm (2020F, 2825F, 3525F)
3
70-120022Plunger 18mm
(2020S, 2825S)
3
40*
70-140027Copper Spacer
3
41*
70-160130O-Ring Ø1.78 x 5.28
3
42*
70-000913Teflon Ring
3
43
70-000320Plunger Rod
3
44
70-1502.04Connecting Rod Pin
3
45
70-010008Connecting Rod
3
46
70-140102Spring Washer
6
47 70-180132Connecting Rod Screw
6
48 70-060104O-Ring Ø2.62 x 107.62
1
49
70-020352Crankcase Cover
1
50
70-060302Gasket
1
51
70-070005Sight Glass
1
Repair kit
number
Kit
description
item numbers
included
Number of
cylinders Kit
will service
70-261408
70-261410
70-261409
70-261411
70-261404
70-261405
70-260028
70-260826
Plunger Seal
15mm
GE 2020F
GE 2825F
GE 3525F
Plunger
Seal
18mm
GE 2020S
GE 2825S
Complete Seal
Packing 15mm
GE 2020F
GE 2825F
GE 3525F
Complete
Seal Packing
18 mm
GE 2020S
GE 2825S
Plunger
15mm
GE 2020F
GE 2825F
GE 3525F
Plunger
18mm
GE 2020S
GE 2825S
Complete
Valve
Plunger
Oil Seals
3, 5, 6
3, 5, 6
2, 3, 4, 5,
6, 7
3, 4, 5, 6,
7, 8
38, 39, 40,
41, 42
38, 39, 40,
41, 42
11, 12, 13
2
3
3
1
1
1
1
6
3
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
22
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
LOW OPERATING
PRESSURE
Faulty pressure gauge
Install new gauge.
Insufficient water supply
Use larger garden hose; clean filter washer at water
inlet.
Old, worn or incorrect spray nozzle
Match nozzle number to machine and/or replace
with new nozzle.
Plumbing or hose leak
Check plumbing system for leaks. Re-tape leaks with
teflon tape.
Faulty or mis-adjusted unloader valve
(where applicable)
Adjust unloader for proper pressure. Install repair kit
when needed.
Worn packing in pump
Install new packing kit.
Fold or dirty inlet or discharge valves in Clean inlet or discharge valves.
pump
DETERGENT NOT
DRAWING
Worn inlet or discharge valves
Replace with valve kit.
Air leak
Tighten all clamps. Check detergent lines for holes.
Valve in the injector head may be blocked, Clean or replace valve in injector.
dirty, or damaged
Filler screen on detergent suction hose Clean or replace.
plugged
Dried up detergent plugging metering valve
Disassemble and clean thoroughly.
High viscosity of detergent
Dilute detergent to specifications.
Hole in detergent line(s).
Repair hole.
Low detergent level
Add detergent if needed.
Discharge water temperature above 180° F
Lower discharge water temperature.
Pump sucking air
PUMP RUNNING
NORMALLY BUT
Valves sticking
PRESSURE LOW
Unloader valve seat faulty
ON INSTALLATION
FLUCTUATING
PRESSURE
PUMP NOISY
Check water supply and possibility of air
Check and clean or replace if necessary.
Check and replace if necessary
Nozzle incorrectly sized
Check and replace if necessary (see serial plate for
proper size).
Worn piston packing
Check and replace if necessary.
Valves worn
Check and replace if necessary.
Blockage in valve
Check and replace if necessary.
Pump sucking air
Check water supply and air see page at joints in
suction line.
Worn piston packing
Check and replace if necessary.
Air in suction line
Check water supply and connections on suction line.
Broken or weak inlet or discharge valve Check and replace if necessary.
springs
Excessive matter in valves
Check and clean if necessary.
Worn bearings
Check and replace if necessary.
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL 23
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
LOW WATER
TEMPERATURE
Improper fuel or water in fuel
Drain fuel tank and replace with proper fuel.
Low fuel pressure
Increase fuel pressure.
Weak fuel pump
Check fuel pump temperature. Replace pump if
needed.
Fuel filter partially clogged
Replace as needed.
Soot build up on coils
Clean coils with soot remover.
Lime build up on coils
Clean inside of coils using coil cleaner.
Improper burner nozzle
Call technical service for proper size.
Incoming water to machine warm or hot
Lower incoming water temperature.
Fuel pump pressure too high
Lower fuel pressure.
Fuel pump defective
Replace fuel pump.
Detergent line sucking air
Tighten all clamps. Check detergent line for holes.
Defective high limit switch (thermostat)
Replace.
Insufficient water supplied
Check GPM to machine.
Restricted water flow
Check nozzle for obstruction, proper size.
WATER
TEMPERATURE
TOO HOT
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
24
STP SERIES PRESSURE WASHER
OPERATOR’S MANUAL
preventative maintenance
This pressure washer was produced with the best available materials and quality craftsmanship. However, you
as the owner have certain responsibilities for the correct care of the equipment. Attention to regular preventative
maintenance procedures will assist in preserving the performance of your equipment. Contact your Shark Pressure
Washers dealer for maintenance. Regular preventative maintenance will add many hours to the life of your pressure
washer. Perform maintenance more often under severe conditions.
MAINTENANCE SCHEDULE
Replace Fuel Lines
Pump Oil
Annually
Inspect
Daily inspect the oil level
Change
After first 50 hours, then every 500 hours or annually
Clean Burner Filter
Monthly (more often if fuel quality is poor)
Remove Burner Soot
Annually
Burner Adjustment/Cleaning
Annually
Descale Coil
Annually (more often if required)
Replace High Pressure Nozzle
Every 6 months
Replace Quick Connects
Annually
Clean Water Screen/Filter
Weekly
Clean Float/Supply Tank
Every 6 months
Replace HP Hose
Annually if there is any sign of wear
Grease Motor
Every 10,000 hours
Replace Burner Nozzle
Annually
Oil Change Record
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07
Date Oil Changed
Month/Day/Year
Estimated Operating
Hours Since Last
Oil Change
SHARK LIMITED NEW PRODUCT WARRANTY
PRESSURE WASHERS
WHAT THIS WARRANTY COVERS
All SHARK PReSSuRe WASHeRS are warranted by SHARK to the original purchaser to be free from defects in materials
and workmanship under normal use, for the periods specified below. This Limited Warranty is subject to the exclusions shown
below, is calculated from the date of the original purchase, and applies to the original components only. Any parts replaced
under this warranty will assume the remainder of the part’s warranty period. This warranty applies to the original purchaser
and is not transferable.
LIMITED LIFETIME PARTS WARRANTY:
Components manufactured by SHARK, such as frames, handles, and belt guards. Forged brass pump manifold. All heating
coils will have a three year warranty. Internal components (excluding oil seals) on the oil-end of Shark pressure washer pumps
will have a seven year warranty. General, AR, Comet and swash and wobble plate pumps have a one year warranty.
ONE YEAR PARTS AND 90 DAYS LAbOR WARRANTY:
All other components, excluding normal wear items as described below, will be warranted for one year on parts. Warranty on
these parts will be for one year regardless of the duration of the original component manufacturer’s part warranty.
WARRANTY PROVIDED bY OTHER MANUFACTURERS:
Motors, generators, and engines, which are warranted by their respective manufacturers, are serviced through these manufacturers’ local authorized service centers. SHARK cannot provide warranty on these items.
WHAT THIS WARRANTY DOES NOT COVER
This warranty does not cover the following items:
1. Normal wear items, such as nozzles, guns, discharge hoses, wands, quick couplers, seals, filters, gaskets, O-rings,
packings, pistons, pump valve assemblies, strainers, belts, brushes, rupture disks, fuses, pump protectors.
2. Damage or malfunctions resulting from accidents, abuse, modifications, alterations, incorrect installation, improper
servicing, failure to follow manufacturer’s maintenance instructions, or use of the equipment beyond its stated usage
specifications as contained in the operator’s manual.
3. Damage due to freezing, chemical deterioration, scale buildup, rust, corrosion, or thermal expansion.
4. Damage to components from fluctuations in electrical or water supply.
5. Normal maintenance service, including adjustments, fuel system cleaning, and clearing of obstructions.
6. Transportation to service center, shop labor charges, field labor charges, or freight damage.
WHAT YOU MUST DO TO ObTAIN WARRANTY SERVICE
While not required for warranty service, we request that you register your SHARK pressure washer by returning the completed
registration card. In order to obtain warranty service on items, you must return the product to an Authorized SHARK Dealer,
freight prepaid, with proof of purchase, within the applicable warranty period. If the product is permanently installed, you
must notify your Authorized SHARK Dealer of the defect. The Authorized Dealer will file a claim, which must subsequently
verify the defect. In most cases, the part must be returned to SHARK freight prepaid with the claim. For warranty service on
components warranted by other manufacturers, the Authorized Dealer can help you obtain warranty service through these
manufacturers’ local authorized service centers.
LIMITATION OF LIAbILITY
SHARK’S liability for special, incidental, or consequential damages is expressly disclaimed. In no event shall SHARK’S liability
exceed the purchase price of the product in question. SHARK makes every effort to ensure that all illustrations and specifications are correct, however, these do not imply a warranty that the product is merchantable or fit for a particular purpose, or that
the product will actually conform to the illustrations and specifications. THE WARRANTY CONTAINED HEREIN IS IN LIEU
OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE. SHARK does not authorize any other party, including authorized Dealers, to make any representation or promise on behalf of SHARK, or to modify the terms, conditions, or limitations in any way. It is the buyer’s responsibility
to ensure that the installation and use of SHARK products conforms to local codes. While SHARK attempts to assure that its
products meet national codes, it cannot be responsible for how the customer chooses to use or install the product.
SHARK PReSSuRe WASHeRS
www.shark-pw.com
Shark STP • 8.914-341.0 / 97-6153 • REV. 6/07