Zanussi ZSF 6280 Operating instructions

Dishwasher
ZSF 6280
User information
g
Dear Customer,
Please read these user instructions carefully and
keep them to refer to later.
Please pass the user instructions on to any future
owner of the appliance.
The following symbols are used in the
text:
1 Safety instructions
Warning! Notes that concern your personal
safety.
Important! Notes that show how to avoid
damage to the appliance.
3 Useful tips and hints
2 Environmental information
2
Contents
Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
Diagram of Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Control Panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
Switching on for the first time – setting the language. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Basic operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting an option/setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
10
Prior to Using for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Water Softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding dishwasher Salt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Filling Up with Rinse Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the acoustic signal:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
10
12
13
14
In daily use. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loading cutlery and dishes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Height of the Upper Basket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adding Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using 3in1 detergents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the dishwashing cycle (Cycle Table) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Starting a Dishwashing Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Delay Timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Switching Off the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Button lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
19
20
22
23
25
25
26
26
Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
What to do if … . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remedying small malfunctions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
If the Dishwashing Results are not Satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
30
30
30
32
Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
33
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34
Notes for Test Institutes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35
Installation and connection instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Safety Information for the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
Installing the Dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
37
Connecting the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
39
41
Service and Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
43
3
Operating Instructions
1 Safety
Prior to using for the first time
• Follow the ”Instructions for installation and connection”.
Correct Use
• The dishwasher is only intended for washing domestic dishes.
• Additions or modifications to the dishwasher are
not permitted.
• Use only special salt, detergent and rinse aid suitable for domestic dishwashers.
• Do not put any solvents in the dishwasher. This
could cause an explosion.
Child Safety
• Keep packaging away from children. There is a risk
of suffocation.
• Children often do not recognise the hazards associated with electrical appliances. Don’t allow children to use the dishwasher unsupervised.
• Make sure that children and pets don’t climb into
the dishwasher. Could endanger life!
• Dishwasher detergents can cause chemical burns
to the eyes, mouth and throat. Could endanger life!
Comply with the safety instructions of the dishwasher detergent manufacturer.
• The water in the dishwasher is not for drinking.
Risk of chemical burns.
General Safety
• Repairs to the dishwasher are only to be carried
out by qualified/authorised service engineers.
• When the dishwasher is not being used, switch it
off and shut off the water tap.
• Never unplug the appliance by pulling on the cable. Always pull the plug.
• Ensure that the door of the dishwasher is always
closed when it is not being loaded or unloaded. In
this way you will avoid anybody tripping over the
open door and hurting themselves.
• Never sit or stand on the open door.
• If the dishwasher is located in a room where there
may be a frost, remove the connection hose from
the tap after each use of the dishwasher.
4
Dishwasher door safety catch
The dishwasher door has a safety catch which prevents children opening the dishwasher door by mistake.
The door safety catch is set as follows:
1. There is a plate (1) on the lefthand side of the door
handle. You can secure the dishwasher against accidental opening by turning this plate clockwise
(for example, with the handle of a spoon).
2. If the safety catch is engaged, to open the dishwasher you must
– first move the door handle to the left (2) until a
slight resistance is felt.
– then press the door handle upwards (3) / forwards.
3. You can disengage the dishwasher’s door safety
catch by pressing the plate all the way to the left
with your finger.
5
Diagram of Appliance
Top Spray Nozzle
Upper basket spray arm
and lower spray arm
Water softener
unit.
Salt Container
Detergent
Dispenser
Rinse aid
dispenser
Rating plate
Filters
Interior lighting
Control Panel
Display
Program button
ON/OFF button
Options button
Delay Start button
6
Button
Ok/Start
Button
Cancel
Switching on for the first time – setting the
language
1. Press the ON/OFF button.
In the display HELLO appears first.
As soon as the dishwasher is ready for use, this is replaced by LANGUAGE ENGLISH; the word ENGLISH
flashes.
2. Using the Options button, select the desired language.
3. Press the Ok/Start button.
You have changed the display to the desired language. In the display SELECT PROGRAMME is displayed.
3 If you want to change the language at a later
date, please see the section “Resetting the
language”.
7
Display
Info status bar
Text line
Symbol line
The info status bar consists of a row of individual
lamps that is divided into two sections: the left section refers to the Programmes menu, the right section to the Options menu.
• In the Programmes and Options menus you can
see at what stage within a cycle you currently are
(the relevant lamp flashes).
• While a dishwashing cycle is running, the info status bar functions as a programme progress display. You can then see at any time how many
programme stages are still to take place (including
the current programme stage).
The text line indicates in the Programmes menu the
name of the programme selected and the estimated
length of the cycle in minutes.
• In the Options menu the name of the selected option or setting is displayed and the current value
set.
• While a dishwashing cycle is running, in the text
line you can see the name of the current programme stage and the estimated time remaining
for the whole dishwashing cycle.
Using the Options button you can briefly display
the name of the dishwashing cycle.
• If there is a fault, a message is displayed.
The symbols in the symbol line have the following
meanings:
– Permanently lit: Button lock is activated, no operation possible
– Flashing: Button lock is temporarily cancelled; see section “Button lock”
– option active
– Programme selected for hygienic cleaning e.g. of babies’ bottles
– 3 IN 1 option active
– Loudspeaker is switched off; no acoustic signals (BUZZER setting)
8
Basic operation
This section contains basic information regarding the
use of your dishwasher. Please read this section very
carefully.
Programme menu
Options menu
AUTOMATIC
Programbutton
button
Options
EAT-LOAD-RUN
3 IN 1
KEY LOCK
70° INTENSIVE
SETTINGS…
ENERGY
button
Ok/Start
45° GLASS
PREWASH
button
Options
LANGUAGE
WATER HARDNESS
RINSE AID
BUZZER
The Programmes menu
• After switching on the dishwasher, you will find
yourself in the Programmes menu.
• Select your dishwashing cycle here using the Program button. In the Info status bar your current position within the menu is shown.
The Options menu
• Using the Options button, go to the desired option.
In the Info status bar your current position within
the menu is displayed.
• For more detail about the options, refer to the respective sections; for more about the 3 IN 1 option, see the section “Before using the appliance
for the first time”.
• Use the Ok/Start button to switch from the menu
item SETTINGS… to the Settings sub-menu.
• WATER HARDNESS
Set the value for water hardness electronically (value range 1 to 10).
• RINSE AID
If 3 IN 1 option is active: Activate or deactivate
rinse aid inflow
If 3 IN 1 option is not active: Rinse aid inflow is always switched on, even if with RINSE AID the value OFF is selected.
• BUZZER
Activate or deactivate audible beep
3 Using the Cancel button you can get back
from any setting to the 3 IN 1 option.
The Settings sub-menu
Go to the desired setting here using the Options button. In the Info status bar your current position within
the sub-menu is shown.
• LANGUAGE
Set the language of the text line in the display; see
also section “Resetting the language”.
9
Adjusting an option/setting
1. To go to the option or setting that you want to adjust.
2. Press the Ok/Start button. Currently set value
flashes.
3. Using the Options button, set the desired value.
4. Press the Ok/Start button. Newly set value is permanently lit.
5. Using the Options button, you can select another
option or setting.
3 Using the Cancel button, you can cancel a
setting procedure.
Prior to Using for the First Time
wish to use 3 in 1 detergent:
3 If– you
First read the section “Using 3in1 detergents”.
– Do not fill up with special salt or rinse aid.
If you do not use 3in1 detergent, before using for the
first time
1. Set the water softener
2. Fill up with dishwasher salt
3. Fill up with rinse aid
Setting the Water Softener
The water softener must be set manually and electronically:
3 To avoid scale deposits on the dishes and in
the dishwasher, the dishes must be washed
with soft water, i.e. water with a low lime content. The water softener must be set according
to the table to the water hardness in the area
where you live. Your local water company will
be able to give you information about the water hardness in your area.
The dishwasher must be switched off.
Setting manually:
1. Open the dishwasher door.
2. Remove the lower basket from the dishwasher.
3. Turn water hardness dial on the left wall of the
dishwasher interior to O or 1 (see table).
10
Setting electronically:
1. Press the ON/OFF button.
3 If the name of a programme stage is displayed
in the display, a dishwashing cycle is active.
First of all you must cancel the dishwashing
cycle:
– Press the Cancel button. CONFIRM CANCEL?
appears in the display.
– Press the Ok/Start button. This cancels the dishwashing cycle.
2. Go to the WATER HARDNESS setting; see section
“Adapting an option/setting”.
3. Set WATER HARDNESS to the right setting.
If the water softener is set electronically to “1” this
switches off the display of the REFILL SALT message.
Water hardness
Adjusting the hardness setting
in °d1)
in mmol/l2)
51 - 70
43 - 50
37 - 42
29 - 36
23 - 28
9,0 - 12,5
7,6 - 8,9
6,5 - 7,5
5,1 - 6,4
4,0 - 5,0
IV
19 - 22
15 - 18
3,3 - 3,9
2,6 - 3,2
III
11 - 14
1,9 - 2,5
II
4 - 10
0,7 - 1,8
I/II
2
below 4
below 0.7
I
1
no salt necessary
Range
Manual
Electronic
1
103)
9
8
7
6
5
4*
0*
3
1) (°d) German degree, measure of the hardness of water
2) [mmol/l] millimol per litre, international unit for water hardness
3) On this setting the length of the dishwashing cycle may be slightly longer.
*) factory setting
11
Adding dishwasher Salt
To decalcify the water softener, it must be filled up
with dishwasher salt. Use only special salt suitable
for domestic dishwashers.
If you do not use 3 in1 detergent, fill up with dishwasher salt:
– Before using the dishwasher for the first time.
– If when starting a cycle the message REFILL SALT
is displayed.
1. Open the door and remove the lower basket.
2. Unscrew the lid on the salt dispenser by turning it
anti-clockwise.
3. Only when using the dishwasher for the first
time:
Fill the salt dispenser with water.
4. Place the funnel (supplied) over the dispenser
opening.
Fill the dispenser with dishwasher salt; the capacity of the dispenser is approx. 1.0-1.5 kg, depending on the size of the grains. Do not overfill the
dispenser.
3 If water overflows when filling up with dish-
washer salt, this is completely harmless.
5. Clean away any salt remnants from the dispenser
opening.
6. Screw the lid back on in a clockwise direction.
7. Run a dishwashing cycle after filling the salt
dispenser with dishwasher salt. This will wash
away salt water and salt crystals that have been
spilt.
3 Depending on the size of the grains, it can
take several hours for the salt to dissolve in
the water and for the message REFILL SALT
not to be displayed when starting a dishwashing cycle.
12
Filling Up with Rinse Aid
Rinse aid causes the rinse water to flow easily from
the crockery leaving gleaming dishes and glassware.
If you do not use 3in1 detergent, fill up with rinse aid:
– Before using the dishwasher for the first time.
– If when starting a dishwashing cycle the message
REFILL RINSE AID is displayed.
Use only special rinse aid for dishwashers.
1. Open the door.
The rinse aid compartment is located on the inside
of the dishwasher door.
2. Press the release button on the rinse aid compartment.
3. Open the cover.
4. Pour rinse aid in slowly right up to the broken
“max” line;
this corresponds to a volume of approx. 140 ml
when full.
5. Press the lid shut until it clicks into place.
6. Wipe up any spilt rinse aid with a cloth. Otherwise
there will be too much foam when rinsing.
13
Setting the Amount of Rinse Aid
Required
3 Only change the amount dispensed, if smears,
milky spots (reduce the amount) or dried on
water spots (increase the amount) can be seen
on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The
dosage can be set from 1-6. The dosage is
pre-set to “4” in the factory.
1. Open the dishwasher door.
2. Press the release button on the rinse aid compartment.
3. Open the cover.
4. Set the dosage level.
5. Press the lid shut until it clicks into place.
6. If rinse aid has leaked out, wipe it away with a
cloth.
Setting the acoustic signal:
In addition to the optical display (e.g. indicating the
end of the cycle, errors) you can also choose to set
an acoustic signal.
1. Press the ON/OFF button.
3 If the name of a programme stage is displayed
in the display, a dishwashing cycle is active.
First of all you must cancel the dishwashing
cycle:
– Press the Cancel button. CONFIRM CANCEL?
appears in the display.
– Press the Ok/Start button. This cancels the dishwashing cycle.
2. To go the BUZZER setting; see section “Adjusting
an option/setting”.
3. To switch audible beep (BUZZER) on or off.
When the audible beep is switched off, the symbol
is lit in the display.
14
In daily use
Loading cutlery and dishes
1 Sponges,
cleaning cloths and any other objects that can absorb water must not be
washed in the dishwasher. Plastic and Tefloncoated dishes and pans tend to retain water
droplets. These dishes and pans therefore do
not dry as well as those made of china and
stainless steel.
For washing in the dishwasher, the following cutlery/dishes/pots and pans
are not suitable:
are of limited suitability:
• Cutlery with wooden, horn, china or mother of pearl handles
• Plastic items that are not heat resistant
• Older cutlery with cement
that is sensitive to temperature
• Dishes or cutlery with glued parts
• Pewter or copper items
• Lead crystal glass
• Steel items that rust
• Wooden boards/platters
• Items made from synthetic materials
• Only wash stoneware in the dishwasher if it is specifically
marked by the manufacturer as being dishwasher-safe.
• Glazed patterns may fade if washed very frequently in the
dishwasher.
• Silver and aluminium parts have a tendency to discolour during washing. Food remains, e.g. egg white, egg yolk and
mustard often cause discoloration and staining on silver.
Therefore always clean food residues from silver immediately,
if it is not to be washed straight after use.
• Glass can become dull after a large number of washes.
• Before loading the dishes, you should:
– Remove the worst of the food residues.
– Soak pans with burnt-on food residues.
• When loading the dishes and cutlery, please note:
– Dishes and cutlery must not impede the rotation
of the spray arms.
– Load bowls, cups, glasses, pans, etc. with the
opening downwards so that water cannot collect
in them
– Dishes and items of cutlery must not lie inside
one another or cover one another
– To avoid damage to glasses, they must not touch
one another
– Don’t put small items (e.g. lids) in the baskets for
the dishes, but in the cutlery basket, so that they
can’t fall through the holes.
15
Loading cutlery
1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket because of the
risk of injury.
To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should:
1. Place the grid insert on the cutlery basket
16
2. Place forks and spoons in the cutlery basket's grid
insert with their handles pointing downwards.
Pots, Pans, Large Plates
Load larger and heavily soiled dishes and pans in the
lower basket.
(Max. diameter for plates 29 cm).
To make it easier to load larger dishes, the two rear
plate rests in the lower basket can be folded down
and the cutlery basket in the lower basket can be
moved to the side.
Cups, Glasses, Coffee Service
Load smaller, fragile crockery and long, sharp cutlery
in the knife drawer.
• Arrange items of crockery on and under the folding
cup racks so that they are offset from each other
and water can reach all items.
17
• The cup racks can be folded up out of the way for
tall crockery items.
• Lay or hang wine and brandy glasses in the slots in
the cup racks.
• For glasses with long stems, fold the glass rack to
the right, otherwise fold it away to the left.
• The row of spikes on the left of the upper basket is
also in two parts and can be folded away.
Spikes not folded away: place glasses, mugs etc.
in the upper basket.
Spikes folded away: More room for serving
dishes.
18
Adjusting the Height of the Upper Basket
Maximum height of dishes in the
Upper basket
Lower basket
with upper basket raised
22 cm
30 cm
with upper basket lowered
24 cm
29 cm
3 The
height of the baskets can also be adjusted
when they are loaded.
Raising / Lowering the upper basket
1. Pull out the upper basket completely.
2. Holding the upper basket by the handle, raise it as
far as it will go and then lower it vertically.
The upper basket will latch into the lower or the
upper position.
19
Adding Detergent
Detergents remove the dirt from dishes and cutlery.
The detergent must be added before the cycle starts.
1 Only
use detergent intended for domestic
dishwashers.
The detergent compartment is located on the inside
of the door.
1. If the lid is closed:
Press the release button.
The lid will spring open.
2. Place the detergent in the detergent dispenser. The
markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx.
20/30 ml of detergent.
Follow the manufacturer’s instructions with regard
to dosing and storage.
3. Close the lid and press until it locks into place.
3 In the case of very heavily soiled dishes, fill the
adjoining compartment (1) with additional detergent. This detergent comes into use during
the pre-wash cycle.
20
Concentrated detergents
Today’s detergents for dishwashers are almost exclusively low-alkaline concentrated detergents with
natural enzymes in tablet or powder form.
2
Using 50°C dishwashing cycles in conjunction
with these concentrated detergents reduces
pollution and is good for your dishes, as these
dishwashing cycles are specially matched to
the dirt-dissolving properties of the enzymes
in concentrated detergents. It is for this reason
that using 50 °C dishwashing cycles in conjunction with concentrated detergents can
achieve the same cleaning results that can
otherwise only be achieved using 65 °C cycles.
Detergent tablets
3 Detergent tablets from different manufactur-
ers dissolve at different rates. For this reason,
some detergent tablets do not attain their full
cleaning power during short cycles. Therefore
please use dishwashing cycles with pre-wash
when using detergent tablets.
21
Using 3in1 detergents
These products are detergents with a combined
cleaning, rinsing and salt function.
When the 3in1 function is activated,
– the addition of special salt and rinse aid from the
respective dispenser is prevented.
– If the salt and rinse aid dispensers are empty, this
is not indicated.
– The dishwashing cycles can be up to 30 minutes
longer.
3 If you want to use 3in1 detergents, check
whether these detergents are suitable for your
water hardness. (Follow the manufacturer’s instructions.)
If you want to use 3in1 products
1. Press the ON/OFF button.
2. Go to the 3 IN 1 option.
3. Set the value to ON (see section “Adjusting an option/setting”
symbol lights up in the symbol
line.
Before the start of the dishwashing cycle put 3in1
detergent in the detergent dispenser.
3 As
the rinse aid inflow is automatically
switched off when the 3in1 function is activated, it may come about because of the different
quality standards in the 3in1 detergent, that
the dishes do not dry sufficiently.
If this happens, proceed as follows (see section “Adding rinse aid”):
• Fill up the dispenser (if this is empty) with rinse aid.
• Set rinse aid dosage to “2” mechanically.
• Activate rinse aid inflow.
If you do not want to use 3in1 products
any more
If you want to stop using 3in1 products, please do
the following:
• Deactivate the 3in1 function.
• Fill up the dispensers for salt and rinse aid again.
• Switch the water softener to the highest setting
and perform up to three normal cycles without
loading any dishes.
• Then set the water softener to the water hardness
in your area.
If you want to use 4in1 products
When using "4 in 1" detergents that integrate also
anti- glass corrosion agent into "3 in 1" formula,
please follow the same indication as given for "3 in
1" detergents.
22
Selecting the dishwashing cycle (Cycle Table)
ENERGY
(50°)5)
Dinner service
and cookware,
temperaturesensitive crockery
normally soiled
45° GLASS
Dessert dishes
and coffee service, delicate
glassware
lightly soiled
PREWASH
(cold)6)
Used dishes that are being
All types of dish- stored in the dishwasher
es
and are to be washed later.
Water (litres)
•
•
•
•
•
•
•
•
-
•
•
•
•
-
-
-
-
9
22 - 24
12 - 14
0,8
1,85 - 2,05
0,95 - 1,05
30
120 - 130
130 - 160
12 - 24
•
1,10 - 1,60
-
100 - 120
•
14
heavily soiled,
dried-on food remains, in
particular protein and
starch
-
4
70° INTENSIVE*
Dinner service
and cookware
Energy (kWh)
•
0,9
-
< 0,1
just used, lightly to normally soiled
•
73
Dishes, excluding saucepans
•
12
EAT-LOAD-RUN
(60°)4)
Drying
•
Final rinse
•
1 to 2x
normally soiled,
dried-on food remains
2x
Dinner service
and cookware
2x
AUTOMATIC
(50° - 65°)*3)
Consumption
values2)
Length (minutes)
Type of
soiling
Main wash
Suitable
for:
Pre-wash
Dishwashing
cycle1)
Intermediate rinse
Programme
sequence
1) In all dishwasher programmes with a *, during the final rinse the temperture is raised to 68° for 10 minutes to hygienically clean
e.g. plastic chopping boards or jam jars.
2) The consumption values were obtained under standardised conditions. They depend on how full the baskets for the dishes are.
Variations are therefore possible in practice.
3) When using this cycle the degree of water clouding determines the amount of soiling on the dishes. The length of the cycle and
water and energy consumption can vary greatly – depending upon the load and how dirty the dishes are. Depending upon the
soiling, the temperature of the water will be automatically adjusted to between 50°C and 65°C.
4) When using this cycle, only load the dishwasher half full.
5) Test programme for Test Institutes
6) This cycle does not need any detergent.
23
Selecting a programme
When your dishes look like this, select:
an intensive programme.
a normal or energy-saving programme.
a short programme (e.g. 30 minute programme).
24
Starting a Dishwashing Cycle
1. Check that the spray arms can turn freely.
2. Turn the water tap on fully.
3. Close the door.
4. Press the ON/OFF button.
5. Using the Program button, select the desired programme.
The name of the dishwashing cycle that is currently
selected flashes.
To the right of the name the estimated duration of the
cycle is displayed.
6. Press the Ok/Start button.
The selected dishwashing cycle will begin. In the text
line of the display you will see the name of the current programme stage. Next to this you will see the
estimated remaining duration in minutes.
Using the Options button you can briefly display the
name of the dishwashing cycle in the display.
3 A dishwashing cycle can only be started from
the Programmes menu.
3 During the dishwashing cycle, the remaining
time shown in the display may be adjusted according to the size of the load, degree of soiling, etc.
If the dishwashing cycle does not start:
If after pressing the Ok/Start button, the programme
does not start and a message appears in the display
(REFILL RINSE AID, REFILL SALT or PLEASE
CLOSE DOOR):
• Follow the instructions in the message.
After the problem has been remedied, the cycle
starts automatically.
3 With the messages REFILL RINSE AID or REFILL SALT you can however start the cycle, by
pressing the Ok/Start button again.
3 While
a dishwashing cycle is running, you cannot change the options or settings.
Interrupting or Cancelling a dishwashing cycle
Interrupt a dishwashing cycle that is in progress if it
is absolutely necessary.
Interrupting the dishwashing programme by opening the dishwasher door
1 Hot steam may escape when the door is
opened. There is a risk of scalding.
1.Open the door carefully. The dishwashing cycle will
stop, in the display: PLEASE CLOSE DOOR
2.Close the door. The cycle will continue.
Cancelling the dishwashing cycle
1.Press the Cancel button.
In the display: CONFIRM CANCEL ?
2.Press the Ok/Start button.
The programme is cancelled. In the display:
CHOOSE PROGRAMME
3.If you want to start a new dishwashing cycle,
check whether there is any detergent in the dispenser.
3 Turning off the dishwasher will only interrupt a
selected dishwashing cycle, not cancel it. The
cycle will recommence after turning the dishwasher back on again.
Setting the Delay Timer
3 With
the delay timer you can delay the start of
a dishwashing cycle for between 1 and 19
hours. First set the Delay Start and then the
desired dishwashing cycle.
1.Press the Delay Start button repeatedly until the
desired period by which you want to delay the start
is displayed in the display.
lights up in the symbol line of the display.
2.Select and start dishwashing cycle.
First the pre-set time delay counts down. In the display you will see START IN and the time remaining
until the start of the dishwashing cycle. After the time
delay the dishwashing cycle begins automatically,
the symbol goes out.
Cancelling a delay start:
You can cancel a delay start that is counting down at
any time.
1.Press the Cancel button.
In the display: CONFIRM CANCEL ?
2.Press the Ok/Start button.
The delay start is cancelled. The dishwasher cycle
that is set begins.
25
Switching Off the dishwasher
Switch off the dishwasher if the messages PROGRAMME END and PLEASE SWITCH OFF are being
displayed alternately.
With some dishwashing cycles, the drying fan continues to run even after the end of the cycle.
If the acoustic signal has been enabled, a continuous
tone will sound for 15 seconds at the end of the dishwashing cycle.
If the dishwasher is not switched off, then the acoustic signal is repeated after 3 minutes and after 6 minutes.
1. Press the ON/OFF button. Display goes out.
2. Turn off the water tap.
1 Carefully open the door. Hot steam may escape.
Button lock
Using the KEY LOCK option, you can prevent unintentional use of your dishwasher – perhaps by children. You can temporarily cancel the button lock
(and then operate your dishwasher) or switch off the
button lock again.
Switching the button lock on
1.Switch on the appliance.
2.Go to KEY LOCK option; see section “Adjusting an
option/setting”.
3.Switch on KEY LOCK option.
In the display the
symbol flashes. While the symbol flashes, you can operate the dishwasher.
15 seconds after the last button activation, the
symbol is permanently lit. This locks the buttons.
The button lock remains active even when the dishwasher is switched off and then switched on again.
Cancelling the button lock temporarily
• Hot dishes are sensitive to knocks. Therefore leave
the dishes to cool for about 15 minutes before removing them. You also get a better drying result.
• Dishes dry more quickly if you open the door for a
moment after the cycle has ended and then leave it
slightly open.
1.Press and hold any button (except the ON/OFF
button) for five secoinds.
Symbol
begins to flash, button lock is temporarily
cancelled, you can operate the dishwasher.
If you do not press any buttons for 15 seconds, the
button lock automatically switches itself on
(symbol
is then lit permanently).
Removing the Dishes
Switching the button lock off
3 It is normal for the inner door and the dispens-
1.Cancel the button lock temporarily.
In the display the symbol
flashes.
2.Go to the KEY LOCK option; see section “Adjusting an option/setting”.
3.Switch off the button lock.
Symbol
goes out, you can operate your dishwasher again normally.
ers to be damp.
• Empty the lower basket first, then the upper basket. This way you avoid dripping water from the
upper basket onto dishes in the lower basket.
• The dishwasher's interior light will always be on
when the door of the appliance is open. Therefore,
in order to save energy, you should always close
the door of the dishwasher after having loaded or
removed dishes.
26
Care and cleaning
1 Do
not use furniture care products or aggressive cleaners.
• When necessary, clean the dishwasher’s controls
with a soft cloth.
• Occasionally check the internal dispensers, door
seal and water inlet filter (if fitted) for dirt and clean
them, if necessary.
Cleaning the filters
3 The
filters must be regularly checked and
cleaned. Dirty filters will spoil the wash
results.
1. Open the door and remove the lower basket.
2. Turn the handle about ¼ of a turn anticlockwise (A)
and remove the filter system (B).
3. Grasp the grip hole on the fine filter (1) and remove
it from the micro-filter (2).
4. Clean all filters thoroughly under running water.
5. Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly.
6. Re-insert the flat filter.
7. Place the fine filter in the micro-filter and fit the two
together.
8. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure
that the flat filter does not protrude above the base
of the washing compartment.
1 Under no circumstances may the dishwasher
be used without its filters.
27
Cleaning the spray arm jets
Regularly check the jets in the spray arms for
blockages. When cleaning is necessary, remove spray arm from the fixture and clean jets
with a pointed object (wire or needle). Then
rinse out the spray arm using a strong jet of
water.
3 Do not damage the jet opening.
Upper basket spray arm
1. To remove upper basket spray arm, tilt it down
hard.
2. Clean spray arms jets.
3. Place cleaned upper basket spray arm back in position against the connecting piece: press the two
together firmly, until you feel them snap into place.
28
Bottom spray arm
1. To remove bottom spray arm, pull it upwards out of
its catch.
2. Clean spray arm jets.
3. Place bottom spray arm back in position against
connecting piece and press down firmly, until you
feel it snap into place.
29
What to do if …
Resetting the language
You can reset the language of the display to the factory setting at any time.
1. Press the Cancel button repeatedly until what is
shown in the display no longer changes.
2. Press and hold the Cancel button for six seconds.
LANGUAGE ENGLISH appears in the text line. The
word ENGLISH flashes.
3. Using the Options button, select the desired language.
4. Press the Ok/Start button.
Remedying small malfunctions
If one of the following fault messages is displayed in
the display during operation:
– OPEN THE TAP
– DRAIN BLOCKED
Remedy the fault, then re-start the dishwashing cycle. The cycle will continue.
In the case of other fault messages:
– Cancel the dishwashing cycle.
– Switch the appliance off and on again.
– Select dishwashing cycle.
– Press the Ok/Start button.
If the fault is displayed again, please contact the
Service Force Centre and inform them of the fault
message.
Malfunction
Possible cause
Tap is blocked with limescale or is
faulty.
Check the tap and have it repaired, if
necessary.
The tap is turned off.
Turn on the tap.
The filter (where present) in the
threaded hose fitting on the tap is
1 short warning tone, continu- blocked.
ously repeated, can be heard,
in the display: OPEN THE TAP
Filters in the base of the washing
compartment are blocked.
Water inlet hose has not been correctly positioned.
30
Remedy
Clean the filter in the threaded hose
fitting.
Cancel the dishwashing cycle (see
chapter: Starting a dishwashing cycle);
clean filters (see chapter: Cleaning
the filters).
Check the position of the hose.
Malfunction
Possible cause
2 short warning tones, contin- The spigot is blocked.
uously repeated, can be heard,
in the display: DRAIN
BLOCKED
Water drain hose has not been cor(Rinse water has collected in
rectly positioned.
the dishwasher's interior container).
Remedy
Clean the spigot.
Check the position of the hose.
3 short warning tones, continFirst turn off the water tap, then
The anti-flood system has been triguously repeated, can be heard,
switch off the appliance and contact
gered.
in the display: SERVICE CODE
the Customer Care department.
1 long warning tone can be
heard,
in the display: SPRAYARM
BLOCKED
The upper basket spray arm is
jammed
Open the door carefully .
Hot steam may escape when the
door is opened. There is a risk of
scalding. Arrange the dishes and cutlery in the baskets so that the spray
arm above them can rotate freely.
Close the dishwasher door.
Appliance is switched on, but
does not react to the buttons
being pressed.
Button lock is activated.
Deactivate button lock; see section
“Button lock”.
in the display: PLEASE CLOSE
DOOR
The door of the dishwasher is open. Close the dishwasher door.
The cycle is not starting.
The mains plug is not plugged in.
Connect the plug to a mains socket.
A fuse in the house’s wiring system
is defective.
Replace fuse.
For dishwasher models with a delay
start timer:
A start time has been selected.
If the dishes are to be washed immediately, cancel the delay start.
Rust spots are visible in the
dishwashing compartment.
The dishwashing compartment is
made from stainless steel. Rust
spots in the washing compartment
are due to rust particles from exterOnly wash cutlery, dishes and pans
nal sources (rust particles from water
that are suitable for dishwasher use.
pipes, pans, cutlery, etc.). Remove
such spots with a commercially
available cleaning product for stainless steel.
A whistling noise can be heard
when washing dishes.
Decalcify appliance with commercially available agents for cleaning dishThe whistling is not a cause for con- washers. If the noises can still be
heard after decalcifying the machine,
cern.
use a different brand of detergent for
washing cutlery and dishes.
The dishwasher interior light
does not come on.
The mains plug is not
plugged in.
Connect the plug to a mains socket.
The bulb in the interior light is faulty.
Contact the Customer Care Department.
31
If the Dishwashing Results
are not Satisfactory
The dishes are still dirty.
• The wrong dishwashing cycle was selected.
• The dishes were loaded is such a way that the
dishwashing water did not reach all items. The
baskets for the dishes must not be overloaded.
• The filters in the base of the washing compartment
are dirty or incorrectly positioned.
• Good quality detergent was not used, or too little
was used.
• In the case of scale deposits on the dishes: The
dishwasher salt dispenser is empty or the water
softening system has been incorrectly set.
• The drain hose is incorrectly positioned.
• Pollutants from the water in the dishwasher can
block the jets in the spray arms. You have the option of removing the spray arms from their fixture
for cleaning (see section “Care and Cleaning”).
The dishes do not dry and are not shining.
• Poor quality rinse aid was used.
• The rinse aid dispenser is empty.
There are smears, streaks, milky spots or
a shiny bluish coating on glasses and
dishes.
• Lower rinse aid dosage.
There are dried water drops on the glasses and dishes.
• Increase rinse aid dosage.
• The detergent may be the cause. Contact the detergent manufacturer's customer advice centre.
Glass corrosion
• Contact the detergent manufacturer's customer
advice centre.
32
Disposal
2
Packaging material
2
Old appliance
The packaging materials are environmentally
friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<,
>PS<, etc. Please dispose of the packaging
materials in the appropriate container at your
local waste disposal facilities.
W
The symbol
on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it shall be
handed over to the applicable collection point
for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
1 Warning! When your appliance has finished
its working life, remove the plug from the
socket. Cut off the cable and plug and dispose
of them.
Break the door lock so that the door no longer
shuts. This prevents children from trapping
themselves inside and endangering their lives.
33
Technical data
Capacity:
12 place settings including serving dishes
Permitted water pressure:
1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa)
Electrical connection:
230 V, 13 A, also see the rating plate on the right-hand side of the dishwasher’s interior door
Total output
2250 W
Dishwasher: Free-standing appliances
Dimensions:
850 x 598 x 598 (H x W x D in mm)
Max. weight:
54 kg
5 This appliance conforms with the following EU
Directives:
– 73/23/EEC dated 19.02.1973 Low Voltage Directive
– 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC
– 93/68/EEC dated 22.07.1993 CE Marking Directive
34
Notes for Test Institutes
Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the
test cycle (see “Cycle Table”).
Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener
and the rinse aid dispenser have been filled with salt
and rinse aid respectively, and using the test cycle
(see “Cycle Table”).
Full load:
12 place settings
including serving dishes
Half load:
6 place settings including serving dishes, leaving alternate positions in the
rack free
Amount of detergent required:
5g + 25g (Type B)
20g (Type B)
Rinse aid setting:
4 (Type III)
4 (Type III)
Sample loading arrangements:
Upper basket *)
*) If necessary, move the cup rack from right to left. When doing this, ensure that the cup rack is at the same height.
Lower basket with cutlery basket *)
Cutlery basket
*) If there are cup racks in place on the lefthand side or if beer glass holders are in place, remove them.
35
Installation and connection instructions
1 Safety Information for the Installation
• Only transport the dishwasher in an upright position, otherwise salt water may run out.
• Before using the dishwasher for the first time,
check for any damage caused in transport. Do not
under any circumstances connect an appliance
that is damaged. In the case of damage, please
contact your supplier.
• Never use the dishwasher if the mains cable, water
inlet or drain hose are damaged; or if the control
panel, work top or plinth area are damaged such
that the inside of the appliance is freely accessible.
• Always plug the mains plug into a correctly installed shockproof socket.
• Permanent connection: a permanent connection
must only be installed by a trained electrician.
• Prior to using the appliance for the first time, ensure that the rated voltage and type of supply on
the rating plate match that of the supply where the
appliance is to be installed. The fuse rating is also
to be found on the rating plate.
• Multi-way plugs / connectors and extension cables
must not be used. This could constitute a fire hazard through overheating.
• The dishwasher’s cable must only be replaced by a
Service Force Engineer.
• A water inlet hose with safety valve must only be
replaced by a Service Force Engineer.
36
Installing the Dishwasher
• The dishwasher must be installed on a firm floor
and adjusted to ensure that it is stable and level in
all directions.
• To compensate for unevenness in the floor and to
match the height of the appliance to that of surrounding units, extend the threaded feet using a
screwdriver.
• The drain hose, inlet hose and mains cable must
be laid so that they are able to move freely within
the plinth area, and so that they are not kinked or
crushed when the dishwasher is in position.
• The dishwasher must also be screwed tightly to
the work surface or to the adjoining units. This is
essential to ensure the dishwasher does not tip up.
37
Free-standing appliances
1 If the dishwasher is installed directly next to a
cooker, a heat-insulating, non-flammable panel (laminated with aluminium foil on the side
next to the cooker) must be fitted flush with
the top edge of the work surface (depth 57.5
cm).
If the appliance is built-in under a kitchen work surface, the worktop supplied with the dishwasher can
be removed in the following way:
1. Unscrew the screws from the elbows at the rear
(1).
2. Push the appliance’s worktop backwards about 1
cm (2).
3. Lift the worktop at the front (3) and remove it.
1 If the dishwasher is later used as a free-standing appliance, the work surface supplied with
it must be re-mounted.
3 The plinth on free-standing appliances is not
adjustable.
38
Connecting the dishwasher
Connecting to the water
supply
• The dishwasher can be connected to cold and hot
water supplies up to max. 60°C.
• The dishwasher must not be connected to open
hot water appliances or instantaneous water heaters.
Permitted water pressure
Lowest permitted water pressure:
1 bar (=10 N/cm2 =100 kPa)
Consult your plumber if the water pressure is less than
1 bar.
Highest permitted water pressure:
10 bar (=100 N/cm2 =1 MPa)
If the water pressure is greater than 10 bar, a pressure
reduction valve must be used (available from your
dealer).
Connecting the inlet hose
1 The water inlet hose must not be kinked,
crushed or entangled when it is being connected.
Connect the threaded hose fitting (ISO 228-1:2000)
on the water inlet hose to a tap with an external
thread (¾ inch). The inlet hose is fitted with either a
plastic or a metal nut:
– Only tighten the nut hand tight.
Then do a visual check for water tightness. (Make
sure that the tap is not dripping.)
3 So
that access to the tap in the kitchen is not
restricted by the use of the dishwasher, we
recommend installing an additional tap, or fitting a T-branch to the existing tap.
If you need a longer water inlet hose than that supplied, the following VDE-approved complete hose
sets are to be used. These are available from your local service centre.
Water drainage
Drain hose
1 The drain hose must not be kinked, crushed or
entangled.
Connecting the drain hose:
– Maximum permitted height: 1 metre.
– Minimum required height: 40 cm above the bottom edge of the appliance.
39
Extension hoses
• Extension hoses are available from your local Service Force Centre. To ensure that the function of the
appliance is not impeded, the internal diameter of
extension hoses must be 19 mm.
• Extension hoses must not be laid more than a
maximum distance of 4 metres horizontally; the
maximum permitted height for the connection for
the drain hose is then 85 cm.
Sink outlet connection
• The outlet of the drain hose (ø 19 mm) fits all commonly available sink outlet types. The outer diameter of the sink outlet connection must be at least
15 mm.
• The drain hose must be fixed to the sink outlet
connection using the hose clamp supplied.
Water drainage if the dishwasher is builtin at high level
If the dishwasher is installed at a high level, and the
drain hose connection is less than 30 cm from the
lower edge of the appliance, adapter kit
ET 111099520 must be fitted by your local Service
Force Centre.
Water drainage into sink (only possible
with free-standing appliances)
If you wish to hang the drain hose over the edge of a
sink, use a detachable hose elbow. You can obtain
this from Service Force by referring to spare part
number ET 646 069 190.
1. Fit the elbow to the drain hose.
2. Secure the drain hose so that it cannot slide off the
edge of the sink.
Pass a piece of cord through the hose elbow and
fix it to the wall or the tap.
Anti-flood system
For protection from water damage, the dishwasher is
equipped with a anti-flood system.
In the event of a fault, the safety valve in the water inlet hose immediately interrupts the supply of water to
the appliance and the drain pump is activated. In this
way water can neither escape nor overflow. The remaining water in the appliance is automatically
pumped out.
Should a fault occur when the appliance is switched
on, a buzzing tone can also be heard.
40
Electrical Connection
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person.
1 WARNING
- This appliance must be
earthed.
The manufacturer declines any responsibility should these safety measures not be observed.
Before switching on make sure the electricity supply
voltage is the same as that indicated on the appliance rating plate.
To isolate the dishwasher from the mains, remove
the mains plug.
Important: The plug must still be accessible after
the appliance has been installed.
Changing a fuse
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS 1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The wires on the mains lead are coloured in accordance with the following code.
Green and Yellow:
Blue:
Brown:
Green & Yellow
Earth
Neutral
Live
Blue
• The wire coloured green and yellow must be connected to the terminal marked with the letter “E“ or
by the earth symbol E or coloured green and yellow.
• The wire coloured blue must be connected to the
terminal “N“ or coloured black.
• The wire coloured brown must be connected to the
terminal marked “L“ or coloured red.
• Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must
be secure over the outer sheath.
Brown
Cord Clamp
1 WARNING! A cut off plug inserted into a 13
amp socket is a serious safety (shock) hazard. Ensure that, if it is necessary to cut off
the plug, it is disposed of safely and not retained.
41
Connecting systems
The water inlet hose, drain hose and the mains cable
must all be connected to the side of the dishwasher
as there is no space for them behind the appliance.
2 connection pieces 45° or straight,
outer ø 19 mm, length 30 mm
waterinlet
42
mains
cable
waterdrainage
double valve
mains socket
waterdrainage
mains cable
water inlet
Service and Spare Parts
If the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact
Service Force by telephoning:
0870 5 929 929
Your telephone call will be automatically routed to
the Service Force Centre covering your post code area.
For the address of your local Service Force Centre
and further information about Service Force, please
visit the website at
www. serviceforce.co.uk
Before calling out an engineer, please ensure you
have read the details under the heading „What to do
if...“
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code.
2. Your telephone number.
3. Clear and concise details of the fault.
4. The model and serial number of the appliance
(found on the rating plate)
5. The purchase date.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee service calls.
Customer Care Department
For general enquiries concerning your Zanussi Electrolux appliance, or for further information on Zanussi Electrolux products, please contact our Customer
Care Department by letter or telephone at the address below or visit our website at www.zanussi.co.uk.
Customer Care Department
Major Appliances
Zanussi Electrolux
Addington Way
Luton
Bedfordshire, LU4 9QQ
Tel: 08705 727727 (*)
(*) calls to this number may be recorded for training
purposes.
43
822 612 196-00-300605-03
Subject to change without notice
The Electrolux Group. The world´s No.1 choice.
The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products
(such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in
more than 150 countries around the world.