USER GUIDE
Aleratec
1:2 DVD/CD Copy Cruiser Pro HLXTM
Win/Mac
Part No. 260167
Copyright/Model Identification
The content of this manual is for informational purposes only and is subject
to change without notice.
This manual is copyright with all rights reserved. Under copyright laws, this
manual and the software described within may not be copied, except in the
normal use of the product(s) described within or to make a backup copy.
Copyright© 2010
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com
1:2 DVD/CD Copy Cruiser Pro HLX™ is a trademark of Aleratec, Inc.
Please record the following information to help expedite any warranty claim:
Model No. _ _____________________ Serial No._____________________
Date Purchased _________________________________________________
Place of Purchase _______________________________________________
NOTE: Please store and track the included software, registration codes and
parts carefully. Requests for replacement software, registration codes, and/
or parts may incur a fee.
www.aleratec.com
Radio/TV Interference Statement
The equipment described in this guide emits radio frequency energy. If it
is not installed in accordance with the manufacturer’s instructions, it may
cause interference with radio or television reception.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy.
If not installed and used in accordance with the instruction manual, this
equipment may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be verified by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an electrical outlet on a circuit that is different
from the circuit to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
This equipment has been certified to comply with the limits for a Class B
computing device, pursuant to FCC Rules. In order to maintain compliance
with FCC regulations, shielded cables must be used with this equipment.
Operation with non-approved equipment or unshielded cables is likely to
result in interference to radio and TV reception. The user is cautioned that
changes and/or modifications made to this equipment, without the approval
of manufacturer, could void the user’s authority to operate this equipment.
www.aleratec.com
Safety Regulations
WARNING
To prevent fire or shock hazard, do not expose the
unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to authorized personnel
only.
CAUTION
As the laser beam in this DVD/CD Duplicator
is harmful to the eyes, do not attempt to
disassemble the cabinet. Refer servicing to
authorized personnel only.
The use of optical instruments with this product
will increase eye hazard.
This DVD/CD Duplicator is classified as a
CLASS 1 LASER PRODUCT.
The CLASS 1 LASER PRODUCT label is
located on top of the internal drive enclosure.
CLASS 1
LASER PRODUCT
LASER KLASSE 1
PRODUKT
www.aleratec.com
Table of Contents
Introduction........................................................................................1
Check out Aleratec Online!.....................................................................1
Key Items – 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac.................2
Front Panel...............................................................................................3
DVD/CD Copy Cruiser Pro HLX Win/Mac Display Panel.....................4
Precautions........................................................................................5
Installation...............................................................................................5
Operation.................................................................................................5
Transportation..........................................................................................5
Overview.............................................................................................6
Main Menu...............................................................................................6
Subfunctions............................................................................................7
Using the DVD/CD Duplicator.........................................................10
Inserting Discs.......................................................................................10
Ejecting Discs........................................................................................10
Power Up Sequence............................................................................... 11
Quick Operating Sequence Overview................................................... 11
Main Menu.............................................................................................12
Setup...............................................................................................28
Advanced Setup..............................................................................40
Using the Duplicator as a DVD/CD-Recorder......................................50
Specifications..................................................................................52
Troubleshooting..............................................................................53
Technical Support...........................................................................56
Service and Support........................................................................57
Technical Support FAX Back Form................................................60
www.aleratec.com
www.aleratec.com
Introduction
Thank you for purchasing this 1:2 DVD/CD Copy Cruiser Pro HLX Win/
Mac. Please read this User Guide thoroughly before using this product.
• Page 3 shows the front panel of the 1:2 DVD/CD Copy Cruiser Pro HLX
Win/Mac.
• Page 4 shows the Duplicator LCD Display Panel.
Check out Aleratec Online!
• www.aleratec.com
• www.twitter.com/Aleratec
• www.youtube.com/Aleratec
www.aleratec.com
1
Introduction
Key Items – 1:2 DVD/CD Copy Cruiser Pro HLX Win/
Mac
Display
Panel
LightScribe
DVD/CD
Recorders
(2)
Power
Switch
Note: Choose a Good Location
1. Allow adequate clearance for moving parts.
2. Do not place near heat sources such as radiators or air ducts, or in a
place subject to direct sunlight, excessive dust, mechanical vibration or
shock.
3. Good care will help assure maximum product life. Improper operating
environment and misuse may void the warranty.
2
www.aleratec.com
Introduction
Front Panel
1
2
3
4
1 Disc Tray
This tray is for loading the disc. It will accept 120 mm and 80 mm
discs. Please place the disc in the exact center of the tray.
2 Emergency Eject Pinhole
In the event of loss of power or failure to open the tray by pressing the
Eject button, insert the straightened end of a large paper clip or similar
rigid object into the Emergency Eject hole to open the tray.
3 Drive LEDs
This indicator lights up when data is being accessed or when data is
being recorded on a disc.
4 Eject Button
This button is used to open or close the tray.
www.aleratec.com
3
Introduction
DVD/CD Copy Cruiser Pro HLX Win/Mac Display Panel
www.aleratec.com
3
2

1
ENT
ESC

4
5
1 Display shows all functions and messages
2 ENT button is used to execute a selected function
3 ESC button is used to cancel a selected function
4 UP arrow is used to scroll up through functions or menus
5 DOWN arrow is used to scroll down through functions or menus
4
www.aleratec.com
Precautions
Before installing your 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac,
please read the following.
Installation
Avoid placing the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac in a
location subject to:
•
•
•
•
•
•
High humidity
High temperature
Excessive dust
Mechanical vibration
Direct sunlight
Electromagnetic radiation
Operation
Do not move the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac during
operation. This may cause it to malfunction during operations.
Avoid exposing the duplicator to sudden changes in temperature as
condensation may form on the lens inside the duplicator. Operating the
duplicator immediately after a sudden increase in temperature may result in
a malfunction during playback or writing operations.
Note: The 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac must never be
cleaned with a lens cleaning kit!
Transportation
Keep the original packing materials for future moving or shipping of the 1:2
DVD/CD Copy Cruiser Pro HLX Win/Mac.
www.aleratec.com
5
Overview
Main Menu
This section provides a listing of the functions on the 1:2 DVD/CD Copy
Cruiser Pro HLX Win/Mac. Detailed descriptions of each function are given
in the next section. The functions are numbered for easy reference; these
numbers are also used in the next section.
There are 12 main menu items that will display in the 1:2 DVD/CD Copy
Cruiser Pro HLX Win/Mac Display Panel. These are:

ENT

1. Copy
7. Disc Info
ESC
ENT

8. Select Source

ENT

2. Test
ENT
ESC

9. Image
ESC

ENT
ENT


ENT
10. Edit Track
ENT
ESC


ENT
11. Setup
ENT
ESC


ENT
ESC


6. Prescan
ESC


5. Compare
ESC


4. Verify
ESC


3. Test & Copy
ESC

12. Adv Setup
ESC
ENT

ESC

Note: Main Menu items “Select Source” (number 8) and “Image”
(number 9) are not supported.
Note: Main Menu items “Edit Track” (number 10) is for Audio disc only.
6
www.aleratec.com
Overview
Subfunctions
The main menu “Edit Track” (for Audio disc only) function has 4 subfunctions.
These are:
10.1 CD to CD Edit
10.2 (Not supported)

10. Edit Track
ENT
ESC

10.3 Play Audio Track
10.4 Close Session
www.aleratec.com
7
Overview
Subfunctions - continued
The main menu “Setup” function has 18 subfunctions. These are:
11.01 Language
11.02 CD Burn Speed
11.03 DVD Burn Speed
11.04 Read Speed (max.)
11.05 Auto Start Drive
11.06 Startup Menu
11.07 Auto Verify*
11.08 Auto Compare*
11.09 Auto Prescan*

11. Setup
ENT
ESC

11.10 Eject Disc*
11.11 Burn On The Fly*
11.12 Burn Mode*
11.13 Display Time
11.14 Button Sound*
11.15 Device Info (Not supported)
11.16 System Info
11.17 Quick Erase Disc
11.18 Full Erase Disc
Note: Functions with options are indicated with an asterisk (*).
8
www.aleratec.com
Overview
The main menu “Adv Setup” (Advanced Setup) function has 16 subfunctions.
These are:
12.01 UnderRun Protect*
12.02 Overburn*
12.03 Read Error Skip*
12.04 (Not supported)
12.05 (Not supported)
12.06 Burn-in
12.07 Update Firmware

12. Adv Setup
ENT
ESC

12.08 Compare Firmware
12.09 Hardware Diagnostic
12.10 Load Default
12.11 CD+G Format (Not supported)
12.12 ISRC
12.13 CD-Text (Not supported)
12.14 USB Option
12.15 USB Auto-Link
12.16 Use Big Block
Note: Functions with options are indicated with an asterisk (*).
www.aleratec.com
9
Using the DVD/CD Duplicator
Inserting Discs
1. Press the Eject button on the DVD/CD Recorder.
2. Place the disc in the tray. The printed (non-shiny) surface of the disc
should be up.
3. To close the tray, press the Eject button or lightly push the front center
of the tray.
Note:
• Never place two discs in the tray at the same time.
• Do not touch the surface of the disc where it has been recorded.
• When using a 120 mm disc, please place it in the center of the tray
where you are able to see the larger position specifically for the 120
mm disc.
• When using a 80 mm disc or Business Card CD-R, please place it in
the center of the tray where you can see the position for the 80 mm
disc.
Ejecting Discs
Disc copies will Auto Eject upon completion of a successful copy. Discs can
also be manually ejected from the drives.
1. Press the drive’s Eject button.
2. Carefully lift the disc from the tray.
3. To close the tray, press the Eject button or lightly push the front center
of the tray.
Note:
• After the tray has been ejected and the disc has been removed
or placed onto the tray, make sure to close the tray to its original
position to avoid the accumulation of dust or miscellaneous items
inside the tray.
• In case of emergency, insert the straightened end of a large paper
clip or similar rigid object into the Emergency Eject Pinhole to open
the tray. Then gently pull the tray out.
10
www.aleratec.com
Using the DVD/CD Duplicator
Power Up Sequence
During the normal powering up sequence the 1:2 DVD/CD Copy Cruiser
Pro HLX Win/Mac will preform a self-test sequence.
Quick Operating Sequence Overview
• Select Copy function by pressing arrow button. Place the source DVD or
CD in the top drive. Place blank DVD-R/RW, DVD+R/RW, CD-R/RW,
or CD-RW media in the DVD/CD-Recorder. After the recorder detects
the blank DVD/CD disc, press the ENT button to start copying.
• When Copy is completed, a good disc copy will be ejected
automatically. Failed discs will remain in the DVD/CD-Recorder
and can be ejected manually. (Default setting: a good disc will be
ejected. This can be changed; see the Set Up section.) For continuous
duplication, reload blank discs into the DVD/CD-Recorder and repeat
the procedure.
• A failed disc will remain in the DVD/CD-Recorder. (Default setting:
A failed disc is NOT ejected.) To manually eject a disc, press the ENT
button to eject a failed disc or press the eject button on the DVD/CDRecorder to eject the disc.
www.aleratec.com
11
Using the DVD/CD Duplicator
Main Menu
Functions are selected with the arrow keys. The numbers correspond to the
Function listing in the previous section.
Copy
During the duplication process, data will be written to a blank DVD-R/RW,
DVD+R/RW, or CD-R/RW disc loaded in the Duplicator. Before starting
the duplication process, please make sure the source DVD/CD is placed in
the DVD/CD-ROM drive.
1. Place a blank DVD-R/RW, DVD+R/RW, or CD-R/RW disc into the
DVD/CD-Recorder; when the DVD/CD-Recorder detects the disc is
present, press the ENT button, and the duplicator will start copying.

1. Copy
ENT
ESC

2. The LCD will display the status of the copying process.
0%
74:00

Copying
650.0MB
ENT
ESC

3. When Copy is finished, the finished copy will be ejected automatically.
Any failed discs will remain in the DVD/CD-Recorder. Press the ENT
button to eject any failed discs.

1. Copy
OK: 03
ENT
ESC

Note: DVD-RW, DVD+RW, and CD-RW discs which already contain
data can also be used as blanks in the 1:2 DVD/CD Copy Cruiser Pro
HLX Win/Mac. Any data stored on -RW discs will be automatically
erased before copying new data. Be sure you do not want data on DVDRW, DVD+RW, or CD-RW discs inserted as blanks as any DVD/CD-RW
discs inserted in the DVD/CD-Recorder to be used as blank media will
automatically be erased, and then the content from the source disc will
be recorded on them.
12
www.aleratec.com
Using the DVD/CD Duplicator
When copying audio CDs, it is highly recommended to copy at a speed
of 16x or lower to ensure the best possible quality audio reproduction.
Go to “Setup” and then “Burning Speed” to change copy speed before
selecting tracks.
www.aleratec.com
13
Using the DVD/CD Duplicator
Main Menu
Test
This function is a test process that simulates data being written to the DVD/
CD-R/RW disc, without actually burning a disc. When the test process is
complete, the DVD-R/RW or CD-R/RW discs will remain blank. For DVDRW or CD-RW discs that contain data, “Test” will quick erase all old data
before simulation. Therefore, never perform “Test” on DVD/CD-RW discs
that contain important data.
Note: Test is not supported by DVD+R/RW discs.
1. Press the ENT button to start the disc simulation, or press ESC to exit.
Pressing ESC before the simulation is complete will not affect the
DVD-R/CD-R disc and they will still remain blank.

2. Test
ENT
ESC

2. For DVD/CD-RW discs that contain data, Test will perform a Quick
Erase before the actual testing. Thus, never run Test on DVD/CD-RW
discs that contain important data.

Erasing Disc
ENT
ESC

3. The LCD will display the status of the erasing and testing of the DVD/
CD.
0%
74:00

Testing
650.0MB
ENT
ESC

4. When the process is completed, the LCD will display the status.
14

2. Test
OK: 03
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
Main Menu
Test & Copy
This function will run Test described above before automatically starting the
Copy Function.
Note: Test & Copy is not supported by DVD+R/RW discs.
1. Press the ENT button to start the test and copy process. Before starting
the Copy function, the Test function as described above will be
performed.

3. Test & Copy
ENT
ESC

2. When testing is completed, the duplicator will start writing data onto
the DVD/CD-R/RW disc.

Testing
650.0MB
0%
74:00
ENT
Copying
650.0MB
0%
74:00
ENT
ESC


ESC

3. When the process is completed, the LCD will display the status.

3. Test & Copy
OK: 03
ENT
ESC

www.aleratec.com
15
Using the DVD/CD Duplicator
Main Menu
Verify
This function will verify that the disc copies can be read correctly in a
DVD/CD-ROM after duplication. Leave the source disc in the DVD/CDROM, and the duplicate disc in the DVD/CD-Recorder will be verified
simultaneously.
1. Press the ENT button to start disc verifying, or press ESC to exit.

4. Verify
ENT
ESC

2. The LCD will display the status of the verification.
0%
74:00

Verify
650.0MB
ENT
ESC

3. When the process is completed, the LCD will display the result.
16

4. Verify
OK: 03
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
Main Menu
Compare
This function will compare the data on the source disc to the target discs
after disc copy.
1. Press the ENT button to do the disc compare, or press ESC to exit.
Press the ENT button again to show detailed “Compare” information.
The LCD display shows information for the source.

5. Compare
ENT
ESC

0%
74:00

Compare
650.0MB
ENT
ESC

2. When the comparison is completed, the LCD will display the result.
OK: 3
Diff: 0

Compare
Fail: 0
ENT
ESC

3. Press ENT again for the status of each copy.

Src: 01 DVD/CD-ROM
Total:
650.0MB
ENT
ESC

4. If the compare result is identical, the LCD will display the message
shown.

Src: 02 DVD/CD-RW
Identical
ENT
ESC

www.aleratec.com
17
Using the DVD/CD Duplicator
Main Menu
Compare - continued
5. If the comparison fails, the LCD will display the number of discs that
failed and passed.
OK: 2
Diff: 0

Compare
Fail: 1
ENT
ESC

6. Press the ENT button again for the status of each copy.

Src: 01 DVD/CD-ROM
Total: 0 Bytes
ENT
ESC

7. If the comparison fails, the LCD will display the reason for the failure.
18

Src: 02 DVD/CD-RW
TOC not match
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
Main Menu
Prescan
This function will scan the source disc and determine if it can be read
correctly and test the reading speed. The reading speed of the source disc
should be higher than the writing speed for the target disc(s).
1. Press the ENT button to prescan the disc, or press ESC to exit.

6. Prescan
ENT
ESC

2. The LCD will display the status of the prescan.
0%
74:00

Scanning
650.0MB
ENT
ESC

3. If a disc can be read correctly, the LCD will display OK.

Prescan OK!
ENT
ESC

4. If it cannot read the source disc correctly, the LCD will display FAIL. A
FAIL disc cannot be copied.

Prescan Fail!
ENT
ESC

www.aleratec.com
19
Using the DVD/CD Duplicator
Main Menu
Disc Info
This function will show the track information of the source disc.
1. Press the ENT button to show the disc information, or press ESC to exit.

7. Disc Info
ENT
ESC

2. The LCD will display the results of the disc information.

Total 02 Sessions
Total 10 Tracks
ENT
ESC

3. Press the ENT button again and the LCD will display the time and
capacity of the source disc.

Total 74:00
Total 10 Tracks
ENT
ESC

4. Press the ENT button again, and use the arrow keys to display
information on the sessions.

Session 01
Track 01 - 09
ENT
ESC

5. Press the ENT button again, and use the arrow keys to display
information on the tracks.
20

Track 01
AUDIO 03:54
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
Main Menu
Select Source (Not supported)
Image (Not supported)
www.aleratec.com
21
Using the DVD/CD Duplicator
Main Menu
Edit Track
Edit Track is a function that allows you to create your own audio
compilation CDs. Several tracks can be selected from different CDs and
copied to one or more blank CDs. When copying audio CDs, it is highly
recommended to copy at a speed of 16x or lower to ensure good quality
audio reproduction. Go to “Setup” and then “Burning Speed” to change
copy speed before selecting tracks.
This function includes 4 subfunctions. These are:
10.1 CD to CD Edit
10.2 (Not supported)

10. Edit Track
ENT
ESC

10.3 Play Audio Track
10.4 Close Session
22
www.aleratec.com
Using the DVD/CD Duplicator
Main Menu
Edit Track
10.1 CD to CD Edit
1. Insert a Source CD into the DVD/CD-ROM and the blank disc in the
DVD/CD-Recorder.
2. Use UP Arrow or DOWN Arrow to scroll through the menu until “Edit
Track” is displayed on the LCD screen. Press the ENT button to select
or press ESC to go to the next setting.

10. Edit Track
ENT
ESC

3. Select “CD to CD Edit” displayed on the LCD screen.

10. Edit Track
CD to CD Edit
ENT
ESC

4. Press ENT and scroll to “Select Track” to select the track you want to
copy. Press the ENT button to select the track, a “+” will appear by the
track selected. Pressing the ENT button again will cancel the selection.

Select Track:
1/10
03:25
Select Track:
+1/10
03:25
ENT
ESC


ENT
ESC

www.aleratec.com
23
Using the DVD/CD Duplicator
Main Menu
Edit Track
10.1 CD to CD Edit - continued
5. Repeat for all tracks you want to copy. Then use the arrow keys to move
to END, then press the ENT button to finish disc editing. Use the arrow
keys to make YES or NO selection. Select YES by pressing the ENT
button.

Select Track:
End
1Trk03:25
ENT
End edit disc
and burn? Yes
ENT
ESC


ESC

6. The LCD will display the status of the copying process. At the completion
of the copying process, the LCD will display the “Burn Complete!”
message. Press the ENT button to continue to step 7.
ENT
ESC


Burn Complete!
OK: 03
Edit

Copying
1/10 - > 1/1
ENT
ESC

7. The system will display: “Continue Edit”, “Next Disc? Yes”. Use the
arrow keys to make YES or NO selection. To continue, select YES to
select tracks from the next disc. Repeat steps 1 - 7. If YES is selected, the
source disc will be ejected. Insert another audio disc to be edited.
24

Continue edit
next Disc? Yes
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
8. When you have finished and the display shows: “Continue Edit”, Next
Disc? Yes”, use the arrow keys to make YES or NO selection. Select NO.

Continue edit
next Disc? No
ENT
ESC

9. The system will ask to close the disc session. “Close all disc’s session?
Yes”. Use the arrow keys to make YES or NO selection. Select YES.

Close all disc’s
session? Yes
ENT
ESC

10. LCD display will show the process of closing the session: “Closing
Session Please Wait —”.

Closing Session
Please wait - - -
ENT
ESC

Note: You will NOT be able to use the new audio CD until you close the
session.
11. When the session is closed, this message will be displayed.

Closing Complete
OK:03
Fail:0
ENT
ESC

www.aleratec.com
25
Using the DVD/CD Duplicator
Main Menu
Edit Track - continued
10.2 (Not supported)
10.3 Play Audio Track
By selecting “Play Audio” you can play music with your 1:2 DVD/CD
Copy Cruiser Pro HLX Win/Mac. You can connect headphones or speakers
to the headphone jack on the DVD/CD-ROM or the speaker jacks on the
back of the unit.
1. Load the CD you want to play in that drive and press the ENT button to
play music. Press ESC to index to the next setting.
ENT
Select Track
1/10
ENT
ESC


04:25
ESC


Playing Track-1
00:00 / 03:35
26

10-03 Edit Track
Play Audio Track
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
10.4 Close Session
Selecting “Close Session” will finalize the disc; no further data can be
added. This function will make the disc readable on a normal CD player.
1. Press the ENT button to enter the setting, or press ESC to index to the
next setting.

10-04 Edit Track
Close Session
ENT
ESC

2. The system will ask to close the disc session. “Close all disc’s session?
Yes”. Use the arrow keys to make YES or NO selection. Select YES.

Close all disc’s
session? Yes
ENT
ESC

3. LCD display will show the process of closing the session: “Closing
Session Please Wait —”.

Close Session
Please Wait---
ENT
ESC

4. When the session is closed, this message will show the passed and
failed discs.

Close Complete
OK:03
Fail:0
ENT
ESC

www.aleratec.com
27
Using the DVD/CD Duplicator
Main Menu
Setup
You can change the original default settings using this setup menu. There
are different settings to control the duplicator’s operation. In general, using
the original default settings for optimal performance is suggested.
This function includes 18 subfunctions. These are:
11.01 Language
11.02 CD Burn Speed
11.03 DVD Burn Speed
11.04 Read Speed (max.)
11.05 Auto Start Drive
11.06 Startup Menu
11.07 Auto Verify*
11.08 Auto Compare*
11.09 Auto Prescan*
�
11. Setup
ENT
ESC
�
11.10 Eject Disc*
11.11 Burn On The Fly*
11.12 Burn Mode*
11.13 Display Time
11.14 Button Sound*
11.15 Device Info (Not supported)
11.16 System Info
11.17 Quick Erase Disc
11.18 Full Erase Disc
28
www.aleratec.com
Using the DVD/CD Duplicator
11.01 Language (Optional)
This function selects the language shown on the display (English,
Traditional Chinese, Simplified Chinese, and Japanese).
1. To select, press the ENT button, or ESC to exit.

11-01. Setup
Language
ENT
ESC

11.02 CD Burn Speed
This setting controls the maximum CD writing speed of the DVD/CDRecorders. The default setting is “Auto”, which will use the highest writing
speed of the recorders. Sometimes maximum writing speed causes a high
failure rate due to poor CD quality or unstable CD writing due to high
speed. Lowering the writing speed will increase the probability of making
successful copies.
1. Press the ENT button to change the setting, or ESC to exit.

11-02. Setup
CD Burn Speed
ENT
ESC

2. Use the arrow buttons to select the desired speed, then press the ENT
button.

CD Burn Speed
Auto
ENT
ESC

www.aleratec.com
29
Using the DVD/CD Duplicator
Main Menu
Setup - continued
11.03 DVD Burn Speed
This setting controls the maximum DVD writing speed of the DVD/CD
Recorders. The default setting is “Auto”, which will use the highest writing
speed of the recorders. Sometimes maximum writing speed causes a high failure
rate due to poor CD quality or unstable CD writing due to high speed. Lowering
the writing speed will increase the probability of making successful copies.
1. Press the ENT button to change the setting, or ESC to exit.

11-03. Setup
DVD Burn Speed
ENT
ESC

2. Use the arrow buttons to select the desired speed, then press the ENT
button.

DVD Burn Speed
Auto
ENT
ESC

11.04 Read Speed
This function sets the reading speed of the source DVD/CD-ROM.
1. Press the ENT button to change the setting, or ESC to exit.

11-04. Setup
Read Speed
ENT
ESC

2. Use the arrow buttons to select the desired reading speed, then press the
ENT button.
30

Read Speed
Maximum
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
11.05 Auto Start Drive
The function of the Auto Start Drive is to copy or test automatically once blank
discs are loaded into recorders.
1. Default setting is OFF. Press ENT button to change, or ESC to exit.

11-05. Setup
Auto Start Drive
ENT
Auto Start Drive
Off
ENT
ESC


ESC

11.06 Startup Menu
This function selects the menu item that will be the first item shown on the
display when you turn on the duplicator. The default setting is “Copy”.
1. Use the arrow buttons to select the desired item (1 - 11), then press the
ENT button.

11-06. Setup
Startup Menu
ENT
Startup Menu
1.Copy
ENT
ESC


ESC

www.aleratec.com
31
Using the DVD/CD Duplicator
Main Menu
Setup - continued
11.07 Auto Verify
This setting controls auto verify of the target discs.
1. Default setting is OFF; press the ENT button to change, or ESC to exit.

11-07. Setup
Auto Verify
ENT
Auto Verify
Off
ENT
ESC


ESC

11.08 Auto Compare
This setting controls auto compare of data between source and target discs
after copying.
1. Default setting is OFF; press the ENT button to change, or ESC to exit.

ENT
Auto Compare
Off
ENT
ESC


32
11-08. Setup
Auto Compare
ESC

www.aleratec.com
Using the DVD/CD Duplicator
11.09 Auto Prescan
This setting controls auto prescan of the master to verify that it can be read
properly, and also tests the reading speed.
1. Default setting is OFF; press the ENT button to change, or ESC to exit.

11-09. Setup
Auto Prescan
ENT
11-09.Prescan
Setup
Auto
Auto Prescan
Off
ENT
ESC


ESC

www.aleratec.com
33
Using the DVD/CD Duplicator
Main Menu
Setup - continued
11.10 Eject Disc
This setting controls the ejection of discs by the DVD/CD-Recorder. Three
options are available: “Eject Good Only”, “Eject All Disc”, and “Do Not Eject”.
1. “Eject Good Only” will only eject the passed disc automatically and leave
a failed disc in the DVD/CD-Recorder.

11-10. Setup
Eject Disc
ENT
Eject Disc
Eject Good Only
ENT
ESC


ESC

2. “Eject All Disc” will eject the disc, whether it has passed or failed.

Eject Disc
Eject All Disc
ENT
ESC

3. If you select “Do Not Eject”, the disc will remain in the DVD/CDRecorder when the job is done and you will have to eject the disc from the
DVD/CD-Recorder manually. Press the ENT button to change the setting,
or ESC to exit.
34

Eject Disc
Do Not Eject
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
11.11 Burn On The Fly
If a disc that contains data is placed in the source drive it will automatically
become the source and burn directly to the target drive with this setting ON.
This setting should always be ON. Data will copy directly from the source drive
to the target drives.
1. Default setting is ON; press the ENT button to change, or ESC to exit.

11-11. Setup
Burn On The Fly
ENT
Burn On The Fly
On
ENT
ESC


ESC

11.12 Burn Mode
This setting controls the writing modes of the disc, including “Disc At Once”
(DAO) or “Track At Once” (TAO).
1. Default setting is “DAO”. Press the ENT button to change, or ESC to exit.

11-12. Setup
Burn Mode
ENT
Burn Mode
DAO
ENT
ESC


ESC

www.aleratec.com
35
Using the DVD/CD Duplicator
Main Menu
Setup - continued
11.13 Display Time
This setting controls the time display.
1. Default setting is ON; press the ENT button to change, or ESC to exit.

11-13. Setup
Display Time
ENT
Display Time
On
ENT
ESC


ESC

11.14 Button Sound
This setting controls the button sound.
1. Default setting is ON; press the ENT button to change, or ESC to exit.

ENT
Button Sound
On
ENT
ESC


36
11-14. Setup
Button Sound
ESC

www.aleratec.com
Using the DVD/CD Duplicator
11.15 Device Info (Not supported)
11.16 System Info
This function will show the system information on the display.
1. Press the ENT button to see the system information, or ESC to exit.
ENT
ESC


System Info

11-16. Setup
System Info
ENT
ESC

www.aleratec.com
37
Using the DVD/CD Duplicator
Main Menu
Setup - continued
11.17 Quick Erase Disc
This function is used for quickly erasing DVD/CD-RW discs.
Note: The Quick Erase Disc simply deletes the directory track, rather
than deleting all the data from the disc (contrast this with Full Erase
Disc).
1. Press the ENT button to enter Quick Erase Disc, or ESC to exit. Use
the arrow keys to select YES or NO, and then press the ENT button to
execute, ESC to go back.

11-17. Setup
Quick Erase Disc
ENT
All data will be
lost, erase? Yes
ENT
Erasing disc
00:24 (Quick)
ENT
ESC


ESC


ESC

2. When the process is finished the display will show the status.
38

Quick Erase
OK:01
Fail:00
ENT
ESC

www.aleratec.com
Using the DVD/CD Duplicator
11.18 Full Erase Disc
This function is similar to the Quick Erase Disc, except it removes all the
data from the DVD/CD-RW disc. The more data on the DVD/CD-RW disc,
the longer time it takes to erase the disc.
1. Press the ENT button to enter Full Erase Disc, or ESC to exit. Use
the arrow keys to select YES or NO and then press the ENT button to
execute, ESC to go back.

11-18. Setup
Full Erase
ENT
All data will be
lost, erase? Yes
ENT
Erasing Disc
00:24 (Full)
ENT
ESC


ESC


ESC

2. When the process is finished the display will show the status.

Full Erase
OK:01
Fail:00
ENT
ESC

www.aleratec.com
39
Using the DVD/CD Duplicator
Main Menu
Advanced Setup
Some advanced setup functions allows users to change the system
configuration. Modification should only be made when you are fully
familiar with all the functions. To enter this function, press and hold the
ESC button for about 2 seconds.
The main menu “Adv Setup” (Advanced Setup) function has 16
subfunctions. These are:
12.01 UnderRun Protect*
12.02 Overburn*
12.03 Read Error Skip*
12.04 (Not supported)
12.05 (Not supported)
12.06 Burn-in
12.07 Update Firmware
�
12. Adv Setup
ENT
ESC
�
12.08 Compare Firmware
12.09 Hardware Diagnostic
12.10 Load Default
12.11 CD+G Format
(Not supported)
12.12 ISRC
12.13 CD-Text (Not supported)
12.14 USB Option
12.15 USB Auto-Link
12.16 Use Big Block
40
www.aleratec.com
Using the DVD/CD Duplicator
12.01 UnderRun Protect
This setting turns Buffer Under Run Protection (also known as “Burn Proof”,
“SafeBurn”, “JustLink”, “Seamless Link”, etc.) ON or OFF.
1. Default setting is ON; press the ENT button to change, or ESC to exit.

12-01. Adv Setup
UnderRun Protect
ENT
UnderRun Protect
On
ENT
ESC


ESC

12.02 Overburn
This function will allow you to burn a few MB more than the standard
capacity of the target Audio CD (e.g. 75 minutes of recording time vs. 74
minutes).
You can activate the overburn function of the DVD/CD-Recorder through
this setting.
1. Default setting is OFF; press the ENT button to change, or ESC to exit.

12-02. Adv Setup
Overburn
ENT
Overburn
Off
ENT
ESC


ESC

www.aleratec.com
41
Using the DVD/CD Duplicator
Main Menu
Advanced Setup - continued
12.03 Read Error Skip
You can set error skipping function while reading discs with errors. The
default setting is OFF. If an error is detected during source loading, the
duplicator will stop loading and display the error message. If the setting is
ON, there will be no message shown even if there is an error in reading.
You can use this function to copy some DVD/CDs with errors.
1. Press the ENT button to change, or ESC to exit.

12-03. Adv Setup
Read Error Skip
ENT
Read Error Skip
Off
ENT
ESC


ESC

12.04 (Not supported)
12.05 (Not supported)
42
www.aleratec.com
Using the DVD/CD Duplicator
12.06 Burn-in
Burn-in is a test function. You can set up to test continuously or for a
specified number of cycles.
1. Load Blank DVD/CD media in the DVD/CD-Recorder and a source
disc in the DVD/CD-ROM drive. The copy process will be simulated,
but data will not be written to the target discs.
Note: Burn In is not supported by DVD+R/RW discs.
2. Go to Burn-in and press the ENT button to enter. You can select Test
to simulate duplication of DVDs/CDs or Erase and Copy to test DVD/
CD-RW erase and write. Use the arrow key to select Continuous or the
number of test cycles you want to run. Press the ENT button to start the
test, or ESC to go back to manual operation.

12-06. Adv Setup
Burn-in
ENT
Burn-in
Test
ENT
Set Burn-in num:
Run Continuous
ENT
ESC


ESC


ESC

3. Select “Erase&Copy” to test erasing and rewriting to DVD/CD-RW
discs only.

Burn-in
Erase&Copy
ENT
ESC

www.aleratec.com
43
Using the DVD/CD Duplicator
Main Menu
Advanced Setup - continued
12.07 Update Firmware
This function is to update your firmware.
1. Make sure there are no discs in the system. Place the disc that contains
the latest firmware data into the DVD/CD-ROM. During updating, do
not turn off the power to the machine, since the updating will not be
finished until the machine resets itself.
2. Press ENT to update. Display will ask if you want to update. Select
YES, then press the ENT button. Do not turn the power off until the
update finishes and the machine resets to COPY.

12-07. Adv Setup
Update Firmware
ENT
Searching F/W--XXX/XXXXX
ENT
ESC


ESC

Procedure to make the Firmware disc:
a. Get the latest firmware download from the Aleratec website at
www.aleratec.com.
Note: Be careful to download the correct firmware; if incorrect
firmware is used the duplicator will not function
b. Unzip the firmware and write the file “cdxxx.bin” to a blank DVD/
CD-R or DVD/CD-RW disc. The Session of the disc has to be
closed.
44
www.aleratec.com
Using the DVD/CD Duplicator
12.08 Compare Firmware
This function compares the current version firmware with the latest version
when the firmware disc is placed into the DVD/CD-ROM.
1. Place the disc that contains the latest firmware data into the DVD/CDROM.

12-08. Adv Setup
Compare Firmware
ENT
ESC

12.09 Hardware Diagnostic
This function will detect the devices connected to the duplicator’s controller
and display information on the hardware.
1. Move to Hardware Diagnostic with the arrow keys and press the ENT
button to enter.

12-09. Adv Setup
H/W Diagnostic
ENT
ESC

2. The display will prompt you first for the button test. Follow the
instructions on the display to test each button.

 Enter ESC
Hold ESC to Exit
ENT
ESC

3. After the button function test, the system will self test and then display
Test Finished.

Test Finished
ENT
ESC

www.aleratec.com
45
Using the DVD/CD Duplicator
Main Menu
Advanced Setup - continued
12.10 Load Default
This function resets the Duplicator’s settings back to their factory default
values.
1. By pressing the ENT button, the duplicator will be reset to it’s factory
default settings.

12-10. Adv Setup
Load Default
ENT
Load Default
Config? Yes
ENT
Load Default
OK
ENT
ESC


ESC


ESC

12.11 CD+G (Not supported)
12.12 ISRC & MCN
ISRC & MCN mean the information of international standard recording code
such as writer, country, year of publication, etc., can be written into each
track.
1. Default setting is OFF; press the ENT button to change, or ESC to exit.

ENT
ISRC & MCN
Off
ENT
ESC


46
12-12. Adv Setup
ISRC & MCN
ESC

www.aleratec.com
Using the DVD/CD Duplicator
12.13 CD-TEXT (Not supported)
12.14 USB Option
This function lets you connect the Duplicator to a computer. Be sure that
your computer supports USB 2.0.
Note: When the USB option is OFF, “14. USB Mode” will be hidden; that
is, it won’t appear in the first layer of the function menu. Only “12. Adv
Setup” will appear. When the USB option is ON, the original “12. Adv
Setup” will change to “12.14 Adv Setup”.
There are two ways to enter USB Mode: Auto and Manual.
1. Auto: The Duplicator has auto link. It will enter “USB L. H Mode”
simply by connecting the USB cable to the USB port of the Duplicator
and the USB port of your computer. The display will appear as shown
at the left. When you are finished with USB Mode, simply disconnect
the USB cable from the computer, and the Duplicator will switch to
Stand Alone.

12-14. Adv Setup
USB Option
ENT
USB L. H Mode
D1: Mult
D2: Mult
ENT
ESC


ESC

www.aleratec.com
47
Using the DVD/CD Duplicator
Main Menu
Advanced Setup
12.14 USB Option - continued
2. Manual: Press the DOWN Arrow to see the following display. Here
you can switch back to standalone mode (copy mode).

Copy Mode
ENT
ESC

3. Press ENT and the display will change to the following display. Press
the DOWN Arrow to switch to YES. Press ENT and the Duplicator
will switch back to the standalone duplicator mode (copy mode).

Back to SA Mode
No
ENT
ESC

4. To go back to USB Mode, go to menu item “12.14 USB Mode” and
press ENT. Press the DOWN Arrow to switch to YES.

Switch USB Mode
No
ENT
ESC

5. Press ENT and the display be as shown.

USB L. H Mode
D1: Mult
D2: Mult
ENT
ESC

Now you are back in computer connect USB mode. From here, you can
return to the Auto Link mode. Make sure the USB cable is connecting
the Duplicator to your computer, and switch the Duplicator’s power
switch to OFF and then back to ON.
48
www.aleratec.com
Using the DVD/CD Duplicator
12.15 USB Auto-Link Option
1. Press ENT and use the UP and DOWN arrows to toggle between ON
and OFF. With USB Auto-Link ON, the controller will enter “USB L.
H Mode” simply by connecting the USB cable to the USB port of the
Duplicator and the USB port of your computer.

USB L. H Mode
D1: Mult
D2: Mult
ENT
ESC

2. When you are finished with USB Mode, simply disconnect the USB
cable from the computer, and the Duplicator will switch to Stand Alone.
12.16 Use Big Block
1. Press ENT and use the UP and DOWN arrows to toggle between ON
and OFF.When ON, Big Block enables the use 128-byte blocks for
more efficient high speed (12x, 16x, 20x) DVD burning.
www.aleratec.com
49
Using the DVD/CD Duplicator
Using the Duplicator as a DVD/CD-Recorder
The 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac can be used as a DVD/
VD-Recorder. Installation consists of connecting the Duplicator to your
computer, and installing the software on your computer.
1. Connect the Duplicator to your computer.
▪▪ Connect the USB 2.0 Data Cable to the Duplicator.
Align and gently attach the USB 2.0 Data Cable.
USB 2.0 Connector
50
Power Connector
www.aleratec.com
Using the DVD/CD Duplicator
▪▪ Connect the USB 2.0 Data Cable to the Duplicator.
Align and gently insert the USB 2.0 Data Cable into an available
USB 2.0 port on your computer, making sure you do not bend the
connector.
▪▪ For P/N 260147 and 260148 and systems running Windows 98SE
only: Install the USB 2.0 Drivers.
If you are running Windows 98SE: After your computer starts up,
insert the USB 2.0 Driver Software in your computer’s DVD/CDROM drive, and run the driver install program to complete your
installation.
Note: This step is not needed if you are not running Windows 98SE.
2. Go to Adv Setup step 13 and switch to USB Mode. Your computer
should recognize the DVD/CD-Recorder in the 1:2 DVD/CD Copy
Cruiser Pro HLX Win/Mac.
3. Install the software from the included CD.
www.aleratec.com
51
Specifications
Loading Mechanisms
• Tray
Supported Media Types
•
•
•
•
•
•
Supported Formats
• Most Industry Standard DVD and CD Formats
Recording Modes
• Disk-at-Once
• Track-at-Once
• Session-at-Once
Copy Speed
• Selectable
Power Requirements
• 115-230 VAC Auto Switching
Dimensions
(height x width x depth)
• 17cm x 17.8cm x 28.9cm
• (6 5/8” x 7”x 11 3/8”)
Weight
• 4.6 kg (10.1 lbs)
Warranty
• Limited 1 Year Parts and Labor
52
DVD-R/RW
DVD+R/RW
CD-R
CD-RW
120mm, mini CD (8cm/3”)
Business Card CD
www.aleratec.com
Troubleshooting
If the 1:2 DVD/CD Copy Cruiser Pro HLX Win/Mac is not performing
as expected, refer to the symptoms in the following table, and follow the
suggested corrective action.
Symptom
Corrective Action
Fail (an issue was
encountered during the
operation)
• Fail messages are usually caused by a problem
recording onto the blank media.
• Errors are more likely to occur with poor quality
media; store brands, generic or bargain brands
should be avoided.
• Reduce the speed at which the duplicator records
using the CD Burn Speed and/or DVD Burn
Speed option in the Setup menu.
• A firmware update may be available to improve
media compatibility; please contact Aleratec
Technical Support for assistance.
Source Disc Empty (the
source disc does not
contain any data)
• Verify that the disc you wish to copy contains the
appropriate data.
• The tray currently set as “source” ejects, which
by default, should be the top tray. If a different
tray opens, the Select Source setting must be
adjusted.
Source Drive Not Ready
(the duplicator did not
detect a disc to copy)
• Check that the disc you wish to copy is inserted
correctly, with the data (shiny) side facing down.
• Verify that the disc you wish to copy can be
read by another device, for example a personal
computer.
• Change to a different source disc and try the
operation again.
Source Drive Read Disc
Error (the disc you wish to
copy may contain errors or
copy protection)
• Remove the source disc and inspect the data
side for scratches, scrapes, smudges or other
contaminants.
• Most commercially produced DVDs are protected
and cannot be copied.
• Prior to any copy attempt, use Prescan to
determine if a particular disc can be read
correctly by the duplicator.
www.aleratec.com
53
Troubleshooting
Symptom
Corrective Action
Target Overflow (the
amount of data on the disc
you wish to copy exceeds
the capacity of the blank
media)
• Use the Disc Info option to determine the type of
disc the source is, and its capacity (listed in MB).
• To copy CDs that have slightly more information
than the normal empty capacity, the Overburn
option must be enabled from Advanced Setup
menu.
• A dual- (double-) layer disc would be required to
copy a DVD containing more than 4,500 MB of
data. These discs have room for about twice the
amount of a standard recordable DVD, about 8.5
GB.
Target Drive Not Ready
(the duplicator was unable
to detect blank disc(s) of
the correct type)
• The disc(s) you wish to copy onto may already
have some data recorded.
• Press the power switch to turn the duplicator off.
Wait for about ten seconds, then power on and
attempt the operation again.
• Check that the disc(s) you wish to copy onto
are inserted correctly, with the data (shiny) side
facing down.
• A CD cannot be copied onto a DVD, or vice
versa. Use the Disc Info function to determine
the format of the source disc.
Copier F/W Fail, Please
Update F/W (the firmware
has become corrupt and
must be reinstalled)
• Contact your support administrator or Aleratec
Technical Support.
Copy completes
successfully but copies fail
to play back or execute.
• Use the Compare function to verify the copied
disc matches the original. For audio CDs, use
Verify instead to ensure the disc is readable.
• Change to a different drive or playback device
and retry.
• Configure the Burn Speed options to record
at a slower speed. Discs burned at maximum
speed (default setting) may cause difficulties for
playback devices.
• Such issues are more likely to occur with poor
quality media; store brands, generic or bargain
brands should be avoided.
54
www.aleratec.com
Troubleshooting
Symptom
Corrective Action
Buttons do not function
when pressed.
• A momentary pause may occur while scrolling
through menu options, as certain functions
require a refresh of the source disc’s details.
• The duplicator still may be busy with the last
task. Check the display for messages that indicate
an operation in progress.
• Button mechanism may be malfunctioning.
Switch the power off, wait 10 seconds, and then
power on again to check for any improvement.
No message on the display
and/or no indicator lights
when powered on.
• Cycle the power by switching the power off,
waiting 10 seconds, and then powering on again.
• Check that the power cord is fastened securely to
the duplicator, and to the electrical outlet.
• Test the electrical outlet with another appliance.
www.aleratec.com
55
Technical Support
After reading this User Guide, if you need additional assistance with this
product, please contact Aleratec Technical Support. Our technical staff will
be happy to assist you, but they may need your help to better assist you.
Calling Aleratec Technical Support without all the necessary information
can be both time consuming and frustrating. Therefore, please try to have
the following information ready before calling:
1. Serial Number - the serial number is located on the back of the DVD/
CD Copy Cruiser Pro HLX Win/Mac.
2. Troubles - your questions about the DVD/CD Copy Cruiser Pro HLX
Win/Mac. Please provide enough information about your problems so
our technical staff can recreate and diagnose it.
Technical Support Addresses and Phone Numbers
XX By e-mail: support@aleratec.com
XX By Telephone: 1-818-678-0484
Technical Support Group can be reached 8:00 AM to 5:00 PM, Pacific
Time, Monday through Friday, excluding U.S. holidays.
Please try to call from a phone near your computer system.
XX Access is available 24 hours a day, 365 days a year, via:
The World Wide Web at: www.aleratec.com
FAX at: 1-818-678-0483
56
www.aleratec.com
Service and Support
Aleratec, Inc., Limited Warranty
This Limited Warranty covers defects encountered in the course of
normal use of this product and does not apply to damage from improper
use, abuse, accidents, unauthorized service, or inadequate packaging
when shipping the product to Aleratec, Inc.
Aleratec, Inc. provides the following limited warranty for this product
only if the product was originally purchased for use, not re-sale, from
Aleratec, Inc., an Aleratec, Inc. authorized dealer or distributor, or any
other Aleratec, Inc. approved reseller for this product. This product is
warranted to be free from defects in workmanship and material for a
period of one year from the date of your original purchase.
If the product fails during normal and proper use within the warranty
period, Aleratec, Inc. will, at its option, repair or replace the product at
no cost (except shipping and insurance). This limited warranty does not
include service to repair damage from improper installation, accident,
disaster, misuse, abuse, or modifications to the subsystem, or by any
other causes unrelated to defective materials or workmanship.
www.aleratec.com
57
Service and Support
Please Note:
This Warranty is valid only within the United States and Puerto Rico,
and applies only to products that are new and unopened on the date
of purchase. For areas outside the United States and Puerto Rico,
contact the authorized dealer from whom you purchased this product to
determine which warranty, if any, applies.
THIS LIMITED WARRANTY CONSTITUTES YOUR SOLE AND
EXCLUSIVE REMEDY, AND THE SOLE AND EXCLUSIVE
LIABILITY OF ALERATEC, INC., AND IS IN LIEU OF ALL
OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF
MERCHANTABILITY OF ITEMS FOR A PARTICULAR PURPOSE.
Your sole remedy shall be repair or replacement, with new or
refurbished components, as provided in this Limited Warranty.
Aleratec, Inc. shall not be liable for any direct, indirect, special
incidental products or consequential damages, including, but not
limited to, any loss of data or loss of profits or business, regardless of
the form of action or theory of liability resulting from any defect in,
or use of, this product (even if Aleratec, Inc. has been advised of the
possibility of such damages).
In any event, the liability of Aleratec, Inc. under this Limited Warranty,
for damages to you or any third party, regardless of the form of action
or theory of liability, shall not exceed the purchase price you paid for
this product.
Some states do not allow limitations of the disclaimer of implied
warranties, the period an implied warranty lasts, or the exclusion or
limitation of incidental or consequential damages, so the exclusions and
limitations stipulated in this Limited Warranty may not apply to you.
This Limited Warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
58
www.aleratec.com
Service and Support
To Obtain Warranty Service:
You must ship your subsystem to the authorized dealer where your
subsystem was purchased within the one year warranty period and
no later than thirty days after discovery of claimed defect, whichever
occurs first. In either case, you must provide proof of original purchase
before any warranty service can be performed. Products and parts
provided as a result of warranty service may be other than new but
will be in good working order and become your property at the time of
exchange. At the same time, the exchanged products or parts become
the property of Aleratec, Inc.
When shipping the subsystem for service, you agree to insure the
Duplicator, to prepay shipping charges, and to use the original shipping
container or equivalent. Any service outside the scope of this limited
warranty shall be at Aleratec, Inc.’s or its Authorized Service Provider’s
rates and terms then in effect.
This warranty gives you specific legal rights; you may also have other
rights which vary from state to state.
www.aleratec.com
59
Technical Support FAX Back Form
Aleratec, Inc.
Technical Support Fax Back Form
Please record the following information to help expedite any warranty claim:
Model No.:_ _____________ Serial No.: _____________________________
Date Purchased _________________________________________________
Place of Purchase:_______________________________________________
To: Technical Support Group FAX: 1-818-678-0483
FROM:_ _____________________FAX: _____________________________
E-MAIL _________________________
RE:_ ________________________TEL: _____________________________
DATE:________________# OF PAGES: _____________________________
I am experiencing the following problems with my 1:2 DVD/CD Copy
Cruiser Pro HLXTM Win/Mac:
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
_____________________________________________________________
By answering these questions, your problem will be solved more rapidly.
Make copies as necessary. You can reach us electronically at: www.aleratec.
com on the internet.
NOTE: Please store and track the included software, registration codes and
parts carefully. Requests for replacement software, registration codes, and/
or parts may incur a fee.
60
www.aleratec.com
Notes:
www.aleratec.com
Document Number: 9399067_ENG_Rev. A Specifications subject to change without notice.
Copyright © 2010
Aleratec, Inc.
9851 Owensmouth Avenue
Chatsworth, CA 91311 U.S.A.
www.aleratec.com