Denon AVR-2105 Operating instructions

AV SURROUND RECEIVER
RÉCEPTEUR AUDIO-VIDÉO
AVR-2105/885
OPERATING INSTRUCTIONS
MODE D’EMPLOI
MASTER VOLUME
FUNCTION
VOLUME LEVEL
SIGNAL
DIGITAL
INPUT MODE
MAIN
SOURCE
ANALOG
EXT. IN
BAND
INPUT
PCM
AUTO
SHIFT
ª
PRESET
STANDARD
5CH / 7CH
STEREO
•
DTS
ª
OUTPUT
SURROUND
ZONE 2
BACK
TUNING
VIDEO SELECT
•
DIMMER
STATUS
ZONE 2 /
REC SELECT
PHONES
ON / STANDBY
ON
SPEAKER
A
OFF
B
SURROUND
BACK
SURROUND
MODE
DIRECT /
STEREO
SELECT
TONE
CONTROL
V.AUX INPUT
SURROUND
PARAMETER
S-VIDEO
VIDEO
L
AUDIO
R
OPTICAL
TONE
DEFEAT
SETUP MIC
AV SURROUND RECEIVER
FOR ENGLISH READERS
PAGE
2 ~ PAGE
73, 144 ~ 148
AVR-2105
POUR LES LECTEURS FRANCAIS
PAGE 2, 74 ~ PAGE 148
2 We greatly appreciate your purchase of this unit.
2 To be sure you take maximum advantage of all the
2 Nous vous remercions pour l’achat de cet appareil.
2 Pour être sûr de profiter au maximum de toutes les
features this unit has to offer, read these instructions
carefully and use the set properly. Be sure to keep this
manual for future reference should any questions or
problems arise.
caractéristiques qu’offre cet appareil, lire avec soin ces
instructions et bien utiliser l’appareil. Toujours
conserver ce mode d’emploi pour s’y référer
ultérieurement en cas de question ou de problème.
“SERIAL NO.
PLEASE RECORD UNIT SERIAL NUMBER ATTACHED TO
THE REAR OF THE CABINET FOR FUTURE REFERENCE”
“NO. DE SERIE
PRIERE DE NOTER LE NUMERO DE SERIE DE L’APPAREIL
INSCRIT A L’ARRIERE DU COFFRET DE FAÇON A POUVOIR
LE CONSULTER EN CAS DE PROBLEME.”
ENGLISH
FRANCAIS
2 SAFETY PRECAUTIONS
FCC INFORMATION (For US customers)
1. PRODUCT
CAUTION
This product complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this product may not cause harmful
interference, and (2) this product must accept any interference received,
including interference that may cause undesired operation.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO
USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING
TO
QUALIFIED
SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
• FOR CANADA MODEL ONLY
2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT
This product, when installed as indicated in the instructions contained in this
manual, meets FCC requirements. Modification not expressly approved by
DENON may void your authority, granted by the FCC, to use the product.
3. NOTE
This product has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This product generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
product does cause harmful interference to radio or television reception,
which can be determined by turning the product OFF and ON, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the product into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the local retailer authorized to distribute this type of product or
an experienced radio/TV technician for help.
• POUR LES MODELE CANADIEN UNIQUEMENT
CAUTION
ATTENTION
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTERODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’ AU
FOND.
2 NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION
• Keep the set free from moisture, water, and
dust.
• Protéger l’appareil contre l’humidité, l’eau et la
poussière.
• Do not let foreign objects in the set.
• Ne pas laisser des objets étrangers dans
l’appareil.
• Avoid high temperatures.
Allow for sufficient heat dispersion when
installed on a rack.
• Eviter des températures élevées.
Tenir compte d’une dispersion de chaleur
suffisante lors de l’installation sur une étagère.
• Unplug the power cord when not using the set
for long periods of time.
• Débrancher le cordon d’alimentation lorsque
l’appareil n’est pas utilisé pendant de longues
périodes.
• Handle the power cord carefully.
Hold the plug when unplugging the cord.
• Manipuler le cordon d’alimentation avec
précaution.
Tenir la prise lors du débranchement du
cordon.
2
* (For sets with ventilation holes)
• Do not obstruct the ventilation holes.
• Ne pas obstruer les trous d’aération.
• Do not let insecticides, benzene, and thinner
come in contact with the set.
• Ne pas mettre en contact des insecticides, du
benzène et un diluant avec l’appareil.
• Never disassemble or modify the set in any
way.
• Ne jamais démonter ou modifier l’appareil
d’une manière ou d’une autre.
SAFETY INSTRUCTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Read Instructions – All the safety and operating instructions
should be read before the product is operated.
Retain Instructions – The safety and operating instructions
should be retained for future reference.
Heed Warnings – All warnings on the product and in the
operating instructions should be adhered to.
Follow Instructions – All operating and use instructions should
be followed.
Cleaning – Unplug this product from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners.
Attachments – Do not use attachments not recommended by
the product manufacturer as they may cause hazards.
Water and Moisture – Do not use this product near water – for
example, near a bath tub, wash bowl, kitchen sink, or laundry
tub; in a wet basement; or near a swimming pool; and the like.
Accessories – Do not place this product on an unstable cart,
stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the
product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer, or sold with the product.
Any mounting of the product should follow the manufacturer’s
instructions, and should use a
mounting accessory
recommended by the
manufacturer.
A product and cart
combination should be
moved with care. Quick
stops, excessive force,
and uneven surfaces may
cause the product and cart
combination to overturn.
Ventilation – Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the product and to
protect it from overheating, and these openings must not be
blocked or covered. The openings should never be blocked by
placing the product on a bed, sofa, rug, or other similar surface.
This product should not be placed in a built-in installation such
as a bookcase or rack unless proper ventilation is provided or
the manufacturer’s instructions have been adhered to.
Power Sources – This product should be operated only from the
type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home, consult your
product dealer or local power company. For products intended
to operate from battery power, or other sources, refer to the
operating instructions.
Grounding or Polarization – This product may be equipped with
a polarized alternating-current line plug (a plug having one blade
wider than the other). This plug will fit into the power outlet
only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the
polarized plug.
FIGURE A
EXAMPLE OF ANTENNA GROUNDING
AS PER NATIONAL
ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
13.
25.
Power-Cord Protection – Power-supply cords should be routed
so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where
they exit from the product.
Outdoor Antenna Grounding – If an outside antenna or cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges. Article 810
of the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding conductors, location
of antenna-discharge unit, connection to grounding electrodes,
and requirements for the grounding electrode. See Figure A.
Lightning – For added protection for this product during a
lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
Power Lines – An outside antenna system should not be
located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power lines
or circuits. When installing an outside antenna system,
extreme care should be taken to keep from touching such
power lines or circuits as contact with them might be fatal.
Overloading – Do not overload wall outlets, extension cords, or
integral convenience receptacles as this can result in a risk of
fire or electric shock.
Object and Liquid Entry – Never push objects of any kind into
this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
Servicing – Do not attempt to service this product yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified
service personnel.
Damage Requiring Service – Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the power-supply cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the product to its normal operation,
e) If the product has been dropped or damaged in any way, and
f) When the product exhibits a distinct change in performance
– this indicates a need for service.
Replacement Parts – When replacement parts are required, be
sure the service technician has used replacement parts
specified by the manufacturer or have the same characteristics
as the original part. Unauthorized substitutions may result in
fire, electric shock, or other hazards.
Safety Check – Upon completion of any service or repairs to this
product, ask the service technician to perform safety checks to
determine that the product is in proper operating condition.
Wall or Ceiling Mounting – The product should be mounted to a
wall or ceiling only as recommended by the manufacturer.
Heat – The product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products
(including amplifiers) that produce heat.
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
3
ENGLISH
2 INTRODUCTION
Thank you for choosing the DENON AVR-2105/885 Digital A / V Surround Receiver. This remarkable component has been engineered to provide
superb surround sound listening with home theater sources such as DVD, as well as providing outstanding high fidelity reproduction of your
favorite music sources.
As this product is provided with an immense array of features, we recommend that before you begin hookup and operation that you review the
contents of this manual before proceeding.
TABLE OF CONTENTS
z
x
c
v
b
n
m
,
.
⁄0
⁄1
⁄2
⁄3
⁄4
⁄5
⁄6
⁄7
⁄8
⁄9
Before Using ...............................................................................................5
Cautions on Installation ...............................................................................5
Cautions on Handling ..................................................................................5
Features ......................................................................................................6
Connections........................................................................................7 ~ 15
Part Names and Functions..................................................................16, 17
Using the Remote Control Unit ................................................................18
Setting up the System......................................................................19 ~ 33
Remote Control Unit.........................................................................34 ~ 38
Multi Zone ........................................................................................45 ~ 47
Surround ...........................................................................................48 ~ 56
DSP Surround Simulation .................................................................57 ~ 60
Listening to the Radio ......................................................................61 ~ 64
Last Function Memory ..............................................................................64
Initialization of the Microprocessor ...........................................................64
Additional Information ......................................................................65 ~ 71
Troubleshooting.........................................................................................72
Specifications ............................................................................................73
Operation ..........................................................................................39 ~ 44
2 ACCESSORIES
Check that the following parts are included in addition to the main unit:
q
w
e
r
r
4
t
y
u
i
Operating instructions .................................................................1
Warranty ......................................................................................1
Service station list .......................................................................1
Remote control unit (RC-980)......................................................1
t
y
R6P/AA batteries .........................................................................2
AM loop antenna .........................................................................1
FM indoor antenna ......................................................................1
Omnidirectional microphone .......................................................1
u
i
ENGLISH
1 BEFORE USING
Pay attention to the following before using this unit:
• Moving the set
To prevent short circuits or damaged wires in the connection cords,
always unplug the power cord and disconnect the connection cords
between all other audio components when moving the set.
• Before turning the power switch on
Check once again that all connections are proper and that there are
not problems with the connection cords. Always set the power
switch to the standby position before connecting and disconnecting
connection cords.
• Note that the illustrations in this instructions may differ from
the actual set for explanation purposes.
• V. AUX terminal
The AVR-2105/885’s front
panel is equipped with a V.
AUX terminal. Remove the
cap covering the terminal
when you want to use it.
SURROUND
MODE
SELECT
TONE
CONTROL
V.AUX INPUT
SURROUND
PARAMETER
S-VIDEO
VIDEO
L
AUDIO
R
OPTICAL
TONE
DEFEAT
SETUP MIC
AV SURROUND RECEIVER
AVR-2105
• Store this instructions in a safe place.
After reading, store this instructions along with the warranty in a
safe place.
2 CAUTIONS ON INSTALLATION
Noise or disturbance of the picture may be generated if this unit or
any other electronic equipment using microprocessors is used near a
tuner or TV.
If this happens, take the following steps:
• Install this unit as far as possible from the tuner or TV.
• Set the antenna wires from the tuner or TV away from this unit’s
power cord and input/output connection cords.
• Noise or disturbance tends to occur particularly when using indoor
antennas or 300 Ω/ohms feeder wires. We recommend using
outdoor antennas and 75 Ω/ohms coaxial cables.
For heat dispersal, leave at least 4 inch/10 cm of space between
the top, back and sides of this unit and the wall or other
components.
4 inch/10 cm or more
4 inch/10 cm or more
Wall
3 CAUTIONS ON HANDLING
• Switching the input function when input jacks are not
connected
A clicking noise may be produced if the input function is switched
when nothing is connected to the input jacks. If this happens, either
turn down the MASTER VOLUME control or connect components
to the input jacks.
• Whenever the unit is in the STANDBY state, the apparatus is
still connected on AC line voltage.
Please be sure to turn the power off (£off) when you leave
home for, say, a vacation.
• Muting of PRE OUT jacks, HEADPHONE jack and SPEAKER
terminals
The PRE OUT jacks, HEADPHONE jack and SPEAKER terminals
include a muting circuit. Because of this, the output signals are
greatly reduced for several seconds after the power switch is
turned on or input function, surround mode or any other-set-up is
changed. If the volume is turned up during this time, the output will
be very high after the muting circuit stops functioning. Always wait
until the muting circuit turns off before adjusting the volume.
5
ENGLISH
4 FEATURES
1. Dolby Digital
Using advanced digital processing algorithms, Dolby Digital
provides up to 5.1 channels of wide-range, high fidelity surround
sound. Dolby Digital is the default digital audio delivery system for
DVD and North American DTV.
8. Multi Zone Music Entertainment System
Multi Source Function:
This unit’s Multi Source function lets you select different audio
sources for listening Different sources can thus be enjoyed in the
main room (MAIN) and the subroom (ZONE2) simultaneously.
2. Dolby Pro Logic IIx compatibility
Dolby Pro Logic IIx furthers the matrix decoding technology of
Dolby Pro Logic II to decode audio signals recorded on two
channels into up to 7.1 playback channels, including the surround
back channel. Dolby Pro Logic IIx also allows 5.1-channel sources
to be played in up to 7.1 channels.
The mode can be selected according to the source. The Music
mode is best suited for playing music,the Cinema mode for playing
movies, and the Game mode for playing games. The Game mode
can only be used with 2-channel audio sources.
9. Future Sound Format Upgrade Capability via Eight Channel
Outputs
For future multi-channel audio format(s), the AVR-2105/885 is
provided with 5.1 channel (five main channels, plus one low
frequency effects channel) inputs, along with a full set of 7.1
channel pre-amp outputs, controlled by the 8 channel master
volume control. This assures future upgrade possibilities for any
future multi-channel sound format.
3. Dolby Pro Logic II Game mode compatibility
In addition to the previously offered Music and Cinema modes, the
AVR-2105/885 also offers a Game mode optimum for games.
4. DTS (Digital Theater Systems)
DTS provides up to 5.1 channels of wide-range, high fidelity
surround sound, from sources such as laser disc, DVD and
specially-encoded music discs.
5. DTS-ES Extended Surround and DTS Neo:6
The AVR-2105/885 can be decoded with DTS-ES Extended
Surround, a multi-channel format developed by Digital Theater
Systems Inc.
The AVR-2105/885 can be also decoded with DTS Neo:6, a
surround mode allowing 6.1 channels playback of regular stereo
sources.
6. DTS 96/24 compatibility
The AVR-2105/885 can be decoded with sources recorded in DTS
96/24, a multi-channel digital signal format developed by Digital
Theater Systems Inc.
DTS 96/24 sources can be played in the multi-channel mode on the
AVR-2105/885 with high sound quality of 96 kHz/24 bits or 88.2
kHz/24 bits.
7. Auto Setup
Use of the microphone for setup applications measures the
presence of speakers, the distance to the speakers, and other
information, and permits automatic setup. The characteristics of
each speaker can also be corrected.
6
10.Front input Terminal
The unit is equipped with a Front Input connector for the
convenient connection of a video camera or other equipment.
11.Video Conversion Function
The AVR-2105/885 is equipped with a function for up-converting
video signals.
Because of this, the AVR-2105/885’s MONITOR OUT jack can be
connected to the monitor (TV) with a set of cables offering a higher
quality connection, regardless of how the player and the AVR2105/885’s video input jacks are connected.
12.Component Video Switching
In addition to composite video and “S” video switching, the AVR2105/885 provides 3 sets of component video (Y, PB/CB, PR/CR)
inputs, and one set of component video outputs to the television,
for superior picture quality.
13.Auto Surround Mode
This function stores the surround mode last used for an input
signal in the memory and automatically sets that surround mode
the next time that signal is input.
14.Preset Memory Tuning
56-Station AM/FM Random Preset Memory tuning.
15.On Screen Display
Troublesome operations such as adjusting the delay time and other
parameters according to the listening environment are greatly
simplified. The various parameters can be set simply by selecting
the graphic displayed on the monitor screen according to the
listening room’s system environment.
ENGLISH
Connecting video components
•
•
•
•
•
To connect the video signal, connect using a 75 Ω/ohms video signal cable cord. Using an improper cable can result in a drop in video quality.
When making connections, also refer to the operating instructions of the other components.
The AVR-2105/885 is equipped with a function for up-converting video signals.
The signal connected to the video signal terminal is output to the S-Video and component video monitor out terminals.
The REC OUT terminals have no conversion function, so when recording only connect the video terminals.
TV or DBS tuner
AUDIO
R
R
OUT
L
VIDEO
OUT
Connecting a TV/DBS tuner
TV or DBS
• Connect the TV’s or DBS tuner’s video output jack (VIDEO OUTPUT) to the
VIDEO (yellow) TV or DBS IN jack using a 75 Ω/ohms video coaxial pin
plug cord.
• Connect the TV’s or DBS tuner’s audio output jacks (AUDIO OUTPUT) to
the AUDIO TV or DBS IN jacks using pin plug cords.
B
L
DVD player or video disc player (VDP), etc.
AUDIO
OUT
R
L
VIDEO
OUT
B
L
R
Connecting a DVD player or a video disc player (VDP)
DVD
• Connect the video disc player’s video output jack (VIDEO OUTPUT) to the VIDEO (yellow)
DVD IN jack using a 75 Ω/ohms video coaxial pin plug cord.
• Connect the video disc player’s analog audio output jacks (ANALOG AUDIO OUTPUT) to the
AUDIO DVD IN jacks using pin plug cords.
• VDP can be connected to the VDP jacks in the same way.
Monitor TV
VIDEO
IN
R
L
Connecting a Monitor TV
MONITOR OUT
• Connect the TV’s video input jack (VIDEO INPUT) to the
VIDEO MONITOR OUT jack using a 75 Ω/ohms video
coaxial pin plug cord.
L
R
L
R
R
L
R
L
R
R
R
OUT
L
R
L
R
IN
L
R
R
OUT
L
R
L
R
AUDIO
OUT IN
VIDEO
Video deck 1
L
IN
L
Note on connecting the digital input jacks
• Only audio signals are inputs to the digital input
jacks. For details. (See page 7)
Video deck 2
L
AUDIO
L
OUT IN
VIDEO
Connecting a video decks
• There are two sets of video deck (VCR) jacks, so two video decks can be connected for simultaneous recording or video copying.
Video input/output connections:
• Connect the video deck’s video output jack (VIDEO OUT) to the VIDEO (yellow) VCR-1 IN jack, and the video deck’s video input jack (VIDEO IN) to the VIDEO
(yellow) VCR-1 OUT jack using 75 Ω/ohms video coaxial pin plug cords.
Connecting the audio output jacks
• Connect the video deck’s audio output jacks (AUDIO OUT) to the AUDIO VCR-1 IN jacks, and the video deck’s audio input jacks (AUDIO IN) to the AUDIO VCR-1
OUT jacks using pin plug cords.
Connect the second video deck to the VCR-2 jacks in the same way.
8
ENGLISH
Connecting the video components equipped with S-Video jacks
• When making connections, also refer to the operating instructions of the other components.
• A note on the S input jacks
The input selectors for the S inputs and Video inputs work in conjunction with each other.
• The AVR-2105/885 is equipped with a function for converting video signals.
• The signal connected to the S-Video signal terminal is output to the composite video and component video monitor out terminals.
• The REC OUT terminals have no conversion function, so when recording only connect the S-Video terminals.
DVD player or video disc
player (VDP)
S-VIDEO
Monitor TV
Connecting a monitor TV
MONITOR OUT
• Connect the TV’s S video input (S-VIDEO INPUT)
to the S-VIDEO MONITOR OUT jack using a S
jack connection cord.
B
OUT
S-VIDEO
Connecting a DVD player or a video disc player (VDP)
DVD/VDP
• Connect the DVD player’s S-Video output jack to the SVIDEO DVD IN jack using a S-Video connection cord.
• VDP can be connected to the VDP jacks in the same way.
• It is also possible to connect a video disc player, DVD
player, video camcorder, game machine, etc., to the V.
AUX jacks.
VIDEO IN
VIDEO OUT
IN
S-VIDEO
B
OUT
TV or satellite broadcast tuner
Connecting a TV or DBS tuner
• Connect the TV’s or DBS tuner’s S video output jack (S-VIDEO
OUTPUT) to the S-VIDEO TV or DBS IN jack using an S-Video
connection cord.
VIDEO OUT
S-VIDEO
VIDEO OUT
OUT
IN
Video deck 1
VIDEO IN
Connecting the video decks
• Connect the video deck’s S output jack (S-OUT) to the S-VIDEO VCR-1 IN
jack and the video deck’s S input jack (S-IN) to the S-VIDEO VCR-1 OUT jack
using S-Video connection cords.
• Connect the video deck’s S output jack (S-OUT) to the S-VIDEO VCR-2 IN
jack and the video deck’s S input jack (S-IN) to the S-VIDEO VCR-2 OUT jack
using S-Video connection cords.
S-VIDEO
OUT
IN
Video deck 2
VIDEO OUT
VIDEO IN
Connect the components’ audio inputs and outputs as described on page 8.
9
ENGLISH
Connecting the antenna terminals
DIRECTION OF
BROADCASTING
STATION
FM INDOOR
ANTENNA
(An Accessory)
FM ANTENNA
75 Ω/ohms
COAXIAL
CABLE
AM OUTDOOR
ANTENNA
GROUND
AM LOOP
ANTENNA
(An Accessory)
An F-type FM antenna cable plug can be connected directly.
AM loop antenna assembly
1
4
2
Connection of AM antennas
Connect to the AM
antenna terminals.
Remove the vinyl tie
and take out the
connection line.
1. Push the lever.
2. Insert the
conductor.
3. Return the lever.
3
Bend in the reverse
direction.
a. With the antenna
on top any stable
surface.
Mount
b. With the antenna
attached to a
wall.
Installation hole Mount on wall, etc.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC which provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
NOTES:
• Do not connect two FM antennas simultaneously.
• Even if an external AM antenna is used, do not disconnect the
AM loop antenna.
• Make sure AM loop antenna lead terminals do not touch metal
parts of the panel.
11
ENGLISH
Connecting the external input (EXT. IN) jacks
• These jacks are for inputting multi-channel audio signals from an outboard decoder, or a component with a different type of multi-channel
decoder, such as a DVD Audio player, a multi-channel SACD player, or other future multi-channel sound format decoder.
• When making connections, also refer to the operating instructions of the other components.
R
L
R
Center
Subwoofer
Surround
Front
L
Decoder with 6-channel
analog output
For instructions on playback using the external input (EXT. IN)
jacks, see page 42.
Connecting the video component equipped with V.AUX jacks
• To connect the video signal, connect using a 75 Ω/ohms video signal cable cord.
MASTER VOLUME
OUTPUT
VOLUME LEVEL
R
L
OPTICAL VIDEO OUT S-VIDEO OUT
ª
TUNING
VIDEO SELECT
•
DIMMER
STATUS
SURROUND
MODE
DIRECT /
STEREO
SELECT
TONE
CONTROL
V.AUX INPUT
SURROUND
PARAMETER
S-VIDEO
VIDEO
L
L
AUDIO
R
R
OPTICAL
TONE
DEFEAT
SETUP MIC
AV SURROUND RECEIVER
AVR-2105
Video camera
OUTPUT
R
L
R
L
VIDEO OUT
S-VIDEO OUT
LINE OUT
VIDEO OUT
S-VIDEO OUT
12
S-VIDEO OUT
OUTPUT
SURROUND
ZONE 2
BACK
VIDEO OUT
•
L
DIGITAL OUT
ESET
R
LINE OUT
DTS
Connecting a Video game component
• Connect the Video game component’s output jacks to
this unit’s V. AUX INPUT jacks.
Video game
Connecting a video camera component
• Connect the video camera component’s output jacks to this
unit’s V. AUX INPUT jacks.
ENGLISH
Speaker system connections
• Connect the speaker terminals with the speakers making sure that
like polarities are matched (≈ with ≈ , √ with √). Mismatching of
polarities will result in weak central sound, unclear orientation of
the various instruments, and the sense of direction of the stereo
being impaired.
• When making connections, take care that none of the individual
conductors of the speaker cord come in contact with adjacent
terminals, with other speaker cord conductors, or with the rear
panel.
NOTE:
NEVER touch the speaker terminals when the power is on.
Doing so could result in electric shocks.
Speaker Impedance
• When speaker systems A and B are use separately, speakers with
an impedance of 6 to 16 Ω/ohms can be connected for use as front
speakers.
• Be careful when using two pairs of front speakers (A + B) at the
same time, since use of speakers with an impedance of 12 to 16
Ω/ohms.
• Speakers with an impedance of 6 to 16 Ω/ohms can be connected
for use as center and surround and surround back speakers.
• The protector circuit may be activated if the set is played for long
periods of time at high volumes when speakers with an impedance
lower than the specified impedance are connected.
Connecting the speaker cords
Connecting banana plugs
1. Loosen by turning
counterclockwise.
2. Insert the cord.
3. Tighten by turning
clockwise.
Banana plug
Turn clockwise to tighten, then insert the
banana plug.
Protector circuit
• This unit is equipped with a high-speed protection circuit. The purpose of this circuit is to protect the speakers under
circumstances such as when the output of the power amplifier is inadvertently short-circuited and a large current flows, when
the temperature surrounding the unit becomes unusually high, or when the unit is used at high output over a long period
which results in an extreme temperature rise.
When the protection circuit is activated, the speaker output is cut off and the power supply indicator LED flashes. Should
this occur, please follow these steps: be sure to switch off the power of this unit, check whether there are any faults with
the wiring of the speaker cables or input cables, and wait for the unit to cool down if it is very hot. Improve the ventilation
condition around the unit and switch the power back on.
If the protection circuit is activated again even though there are no problems with the wiring or the ventilation around the
unit, switch off the power and contact a DENON service center.
Note on speaker impedance
• The protector circuit may be activated if the set is played for long periods of time at high volumes when speakers with an
impedance lower than the specified impedance (for example speakers with an impedance of lower than 4 Ω/ohms) are
connected. If the protector circuit is activated, the speaker output is cut off. Turn off the set’s power, wait for the set to cool
down, improve the ventilation around the set, then turn the power back on.
14
ENGLISH
6 PART NAMES AND FUNCTIONS
Front Panel
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
#0 @8 @7
@2 @0
#3 #2 #1 @9
@6 @5 @4 @3 @1
#5 #4
!9
MASTER VOLUME
FUNCTION
VOLUME LEVEL
SIGNAL
DIGITAL
INPUT MODE
MAIN
SOURCE
ANALOG
EXT. IN
BAND
INPUT
PCM
AUTO
SHIFT
ª
PRESET
STANDARD
5CH / 7CH
STEREO
•
DTS
ª
OUTPUT
SURROUND
ZONE 2
BACK
TUNING
VIDEO SELECT
•
DIMMER
STATUS
ZONE 2 /
REC SELECT
PHONES
ON / STANDBY
ON
OFF
SPEAKER
A
B
SURROUND
BACK
SURROUND
MODE
DIRECT /
STEREO
SELECT
TONE
CONTROL
V.AUX INPUT
SURROUND
PARAMETER
S-VIDEO
VIDEO
L
AUDIO
R
OPTICAL
TONE
DEFEAT
SETUP MIC
AV SURROUND RECEIVER
qwe
t u o !1
r y
i !0
q Power ON/STANDBY switch .......................................(21, 39, 61)
w Power indicator ..................................................................(21, 39)
e Power switch .....................................................................(21, 39)
r Headphones jack (PHONES) ....................................................(43)
t ANALOG button .................................................................(40, 42)
y SPEAKER A/B buttons .......................................................(39, 64)
u SURROUND BACK button .......................................................(54)
i Preset station select buttons ...................................................(63)
o STANDARD button.................................................(48, 50, 52, 54)
!0 5CH/7CH STEREO button ........................................................(58)
!1 DIRECT/STEREO button...........................................................(42)
!2 V. AUX INPUT terminals.......................................................(5, 12)
!3 SETUP MIC jack .......................................................................(22)
!4 SURROUND MODE button......................................................(41)
!5 SURROUND PARAMETER button .....................................(50, 58)
!6 SELECT knob ...............................................................(41, 51, 59)
!7 TONE DEFEAT button ..............................................................(43)
!8 TONE CONTROL button ..........................................................(43)
16
!2
AVR-2105
!4
!3 !5 !6 !7 !8
!9 MASTER VOLUME control ......................................................(41)
@0 TUNING • (up) / ª (down) buttons ..........................................(62)
@1 STATUS button .........................................................................(44)
@2 DIMMER button .......................................................................(44)
@3 VIDEO SELECT button .............................................................(43)
@4 OUTPUT indicator ..............................................................(47, 54)
@5 MASTER VOLUME indicator....................................................(41)
@6 Display
@7 INPUT mode indicator ..............................................................(41)
@8 SIGNAL indicator ......................................................................(41)
@9 BAND button ............................................................................(62)
#0 EXT. IN button ....................................................................(40, 42)
#1 Remote control sensor.............................................................(18)
#2 INPUT MODE button .........................................................(40, 42)
#3 ZONE2/REC SELECT button ..............................................(44, 47)
#4 FUNCTION knob ..........................................................(40, 44, 47)
#5 MAIN button.............................................................................(40)
ENGLISH
Remote control unit
• For details on the functions of these parts, refer to the pages given in parentheses ( ).
LED (indicator) .............................(35, 38)
Remote control signal
transmitter .........................................(18)
POWER buttons ..............(21, 35~37, 39)
ZONE2 buttons ..................................(47)
MAIN buttons ....................................(47)
SURROUND buttons .............(41, 48, 58)
Input source selector buttons
...............................................(35~38, 40)
Tuner system/
System buttons ...............(34, 36, 37, 62)
Mode selector switches
...............................................(34~36, 38)
Master volume control
buttons ...............................................(41)
System buttons .....................(34, 36, 37)
MUTING button .................................(43)
SYSTEM SET UP/
SETUP button ........................(19, 36, 37)
SURROUND PARAMETER/SYSTEM
button ....................................(36, 37, 50)
Cursor buttons .................(19, 36, 37, 51)
CH SELECT (channel select)/ ENTER
button ........................(19, 36, 37, 49, 51)
ON SCREEN/DISPLAY button
...............................................(36, 37, 56)
SURROUND BACK/RETURN
button ....................................(36, 37, 54)
Test tone button.................................(48)
SPEAKER button................................(39)
VIDEO SELECT button.......................(43)
DIMMER button.................................(44)
INPUT MODE selector
buttons.........................................(40, 42)
17
ENGLISH
7 USING THE REMOTE CONTROL UNIT
Following the procedure outlined below, insert the batteries before using the remote control unit.
Range of operation of the remote control unit
Point the remote control unit at the remote control sensor as shown
on the diagram at the left.
30°
30°
Approx. 23 feet/7 m
NOTES:
• The remote control unit can be used from a straight distance of
approximately 23 feet/7 meters, but this distance will shorten or
operation will become difficult if there are obstacles between the
remote control unit and the remote control sensor, if the remote
control sensor is exposed to direct sunlight or other strong light, or
if operated from an angle.
• Neon signs or other devices emitting pulse-type noise nearby may
result in malfunction, so keep the set as far away from such
devices as possible.
Inserting the batteries
q Press as shown by the arrow and slide off.
w Insert the R6P/AA batteries properly, as
shown on the diagram.
e Close the lid.
NOTES:
• Use only R6P/AA batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside the battery compartment.)
• Remove the batteries if the remote control transmitter will not be used for an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching the leaked material or letting it come in contact with clothing, etc. Clean the
battery compartment thoroughly before installing new batteries.
• Have replacement batteries on hand so that the old batteries can be replaced as quickly as possible when the time comes.
• Even if less than a year has passed, replace the batteries with new ones if the set does not operate even when the remote control unit is
operated nearby the set. (The included battery is only for verifying operation. Replace it with a new battery as soon as possible.)
18
ENGLISH
8 SETTING UP THE SYSTEM
• Once all connections with other AV components have been completed as described in “CONNECTIONS” (see pages 7 to 15), make the various
settings described below on the monitor screen using the AVR-2105/885’s on-screen display function.
These settings are required to set up the listening room’s AV system centered around the AVR-2105/885.
Use the following buttons to set up the system
1
2
Set the slide switch to “AUDIO”.
Use the following buttons to set up the system:
SYSTEM SETUP button
Press this to display the system setup on the display.
CURSOR buttons (•, ª, 0, 1)
Press this change what appears on the display.
ENTER button
Press this to switch the display.
Also use this button to complete the setting.
• System setup items and default values (set upon shipment from the factory)
System setup
Default settings
Auto Setup
Power Amp
Assignment
Speaker
Configuration
Input the combination of speakers in your system and their
corresponding sizes (SMALL for regular speakers, LARGE for fullsize, full-range) to automatically set the composition of the signals
output from the speakers and the frequency response.
Set this to switch the surround back
channel’s power amplifier for use for zone2.
SURROUND BACK
Front Sp.
Center Sp.
Large
Small
Surround Sp.
Surround Back Sp.
Subwoofer
Small / 2 spkrs
Yes
Small
Surround
L
Surround
R
Surround
Back L
Surround
Back R
Subwoofer
10 ft
10 ft
10 ft
10 ft
12 ft
Delay Time
This parameter is for optimizing the timing with which the audio
signals are produced from the speakers and subwoofer according
to the listening position.
Subwoofer Mode
This selects the subwoofer speaker for playing deep bass signals.
Subwoofer mode = LFE (Normal)
Crossover
Frequency
Set the frequency (Hz) below which the bass sound of the various
speakers is to be output from the subwoofer.
80 Hz
Test Tone
This adjusts the volume of the signals output from the speakers
and subwoofer for the different channels in order to obtain
optimum effects.
Digital In
Assignment
Component In
Assignment
This assigns the digital input jacks for the different
input sources.
This assigns the component video input jacks for
the different video input sources.
Front L
Front R
Center
12 ft
12 ft
12 ft
Front L
Front R
Center
Surround
L
Surround
R
Surround
Back L
Surround
Back R
Subwoofer
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Input source
CD
DVD/VDP
TV/DBS
VCR-1
VCR-2
CDR/TAPE
Digital
Inputs
COAXIAL
OPTICAL 1
OPTICAL 2
OFF
OFF
OPTICAL 3
Input source
DVD/VDP
TV/DBS
VCR-1
VCR-2
V. AUX
—
Component
Inputs
VIDEO 1
VIDEO 2
VIDEO 3
OFF
OFF
—
Video Input Mode
Set the input signal to be output from the monitor output terminal.
Auto Surround
Mode
AUTO
Auto surround mode function setting.
Auto Surround Mode = ON
Ext. In SW Level
Set the Ext. In Subwoofer channel playback level.
Ext. In SW Level = +15 dB
Power AMP
Assignment
Set this to switch the surround back channel’s power amplifier for
use for Zone 2.
Surround Back
On Screen
Display
This sets whether or not to display the on-screen display that
appears on the monitor screen when the controls on the remote
control unit or main unit are operated.
A setting to prevent flickering.
On Screen Display = ON /Mode 1
19
ENGLISH
System setup
Auto Tuner
Presets
FM stations are received automatically and stored in the memory.
Default settings
A1 ~ A8
87.5 / 89.1 / 98.1 / 107.9 / 90.1 / 90.1 / 90.1 / 90.1 MHz
B1 ~ B8
520 / 600 / 1000 / 1400 / 1500 / 1710 kHz, 90.1 / 90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
NOTES:
• The on-screen display signals are output with priority to the S-VIDEO MONITOR OUT jack during playback of a video component. For
example, if the TV monitor is connected to both the AVR-2105/885’s S-Video and video monitor output jacks and signals are input to the AVR2105/885 from a video source (VDP, etc.) connected to both the S-Video and video input jacks, the on-screen display signals are output with
priority to the S-Video monitor output. If you wish to output the signals to the video monitor output jack, do not connect a cord to the SVIDEO MONITOR OUT jack. (For details, see page 33.)
• The AVR-2105/885’s on-screen display function is designed for use with high resolution monitor TVs, so it may be difficult to read small
characters on TVs with small screens or low resolutions.
• The setup menu is not displayed when headphone are being used.
2 Speaker system layout
Basic system layout
• The following is an example of the basic layout for a system consisting of 8 speaker systems and a television monitor:
Subwoofer
Center speaker system
Surround back speaker system
Front speaker systems
Set these at the sides of the TV or screen with
their front surfaces as flush with the front of the
screen as possible.
20
Surround speaker systems
ENGLISH
Before setting up the system
1
2
Refer to “CONNECTIONS” (pages 7 to 15) and check that all connections are correct.
ON
Press the Power switch (button) .
OFF
• ¢ ON
The power turns on and indicator is light.
Set the power switch to this position to turn the power on and off from the included remote control unit.
• £ OFF
The power turns off and indicator is off.
In this position, the power cannot be turned on and off from the remote control unit.
(Main unit)
3
Turn on the power.
Press the Power ON/STANDBY switch (button).
ON / STANDBY
(Main unit)
4
(Remote control unit)
Press the SYSTEM SETUP button to enter the setting.
*SYSTEM SET UP
NOTE: Please make sure the “AUDIO” position of the slide switch
on the remote control unit.
5
Press the ENTER or
(down) button to switch to the Auto Setup.
NOTE:
Press the SYSTEM SETUP button again to finish system set up. System set up can be finished at any time. The changes to the settings made
up to that point are entered.
Auto setup
The Auto Setup function of this unit performs an analysis of the speaker system to permit an appropriate automatic setting.
When performing Auto Setup, an optional microphone is required for the setup.
2 Measurement and setting details
q : This sets the speaker connection mode, polarity, and bass reproduction ability.
w : This sets the optimum delay time from each speaker corresponding to the listening position.
e : This sets the volume that is output from each speaker.
NOTE:
• A loud test tone is output during the measurement. Please consider this should you be planning night time measurements, and consider
not allowing small children into the listening room at this time.
21
ENGLISH
Connecting the microphone for Auto Setup
1
Connect the microphone for Auto Setup to the Setup Mic
connector on the front panel of the unit.
SPEAKER
PHONES
A
B
SURROUND
BACK
STANDARD
5CH / 7CH
STEREO
SURROUND
MODE
DIRECT /
STEREO
SELECT
TONE
CONTROL
V.AUX INPUT
SURROUND
PARAMETER
S-VIDEO
VIDEO
L
AUDIO
R
OPTICAL
TONE
DEFEAT
SETUP MIC
AV SURROUND RECEIVER
AVR-2105
Listening position
2
Place the microphone for Auto Setup at the actual listening
position which will be at the same height as your ears. Use a
tripod or level surface at positioning.
Setting the Auto Setup
1
• Use the
(left) button to switch the Auto Setup mode.
• Press the ENTER or
configuration set up.
(down) button to switch to the speaker
1 AutoSet
2
<YES
Check the “Power Amp Assign” setting.
• When “Surround Back” is selected, the test tone during Auto Setup will be output from the Surround Back speaker.
• When “ZONE2” is selected, change the setting to “ZONE2” The test tone during Auto Setup is set so that it will not be output to
ZONE2 (Another room).
q Select the Power Amp Assign setting.
w Select “Surround Back” or “ZONE2”.
(Remote control unit)
(Remote control unit)
AutoSet
3
SB >
q Select the “Start”.
(Remote control unit)
AutoSet <Start
22
NOTE:
• When “ZONE2” is selected at System Setup Menu
“Power Amp Assign”, surround back speaker is not
displayed.
w Press the
(left) button to start Auto Setup.
(Remote control unit)
ENGLISH
4
Start the measurements.
Measurement of each channel is performed as follows.
Display
2
1
FL
FR
C
SW
3
SL
SR
SBL
SBR
NOTES:
• Measurement is canceled when MASTER VOLUME is operated
while the Auto Setup is performed.
• Set the volume to halfway and set the crossover frequency to
the maximum or Low pass filter off if your subwoofer speaker
can adjust the output volume and the crossover frequency.
1 Only the front speakers (A) is measured. Even if the
front speakers (B) is set, the setting automatically switches to the front speakers (A) once measurements are completed.
2 Subwoofer speaker is measured twice.
3 When “ZONE2” is selected, this is not displayed.
After each channel is measured, “Calculating” appears.
The display switches to Auto Setup check screen automatically.
About automatic retry
Remeasurement starts automatically to receive proper result of measurement.
Remeasurement is performed to 2 times, and “Retry1” or “Retry2” is displayed on screen during
remeasurement.
About the error message
These error screens will be displayed when performing the measurements of Auto Setup and the automatic measurements can not be completed
because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the pertinent items,
and measure again.
When there is too much noise in the room, the speakers may not be detected properly. Should this happen, perform the measurements when
the noise level is low, or switch off the power of the equipment that is producing the noise for the duration of the measurements.
q This screen will be displayed when the speakers required for
producing suitable reproduction have not been detected.
• The front L and front R speakers were not properly detected.
• Only one channel of the surround speakers was detected.
• Sound was output from the R channel when only one surround
back speaker was connected.
• The surround back was detected, but the surround speaker was
not detected.
Check that the pertinent
speakers are properly
connected (see page 15).
w This screen will be displayed when the speaker polarity is connected
in reverse.
Check the polarity of the
pertinent speakers.
For some speakers, the
screen below may be
displayed even though
the speakers are properly
connected.
If so, select “Skip0”.
e This screen will be displayed when accurate measurements
cannot be made due to the input level to the microphone being
too high.
Set up the speakers so
that their position is
farther away from the
listening position.
Lower the volume of the
subwoofer speaker.
r This screen will be displayed when the measurement microphone
is not connected, or when all of the speakers have not been
detected.
Connect the measurement microphone to the microphone
connector.
Check the speaker connections.
23
ENGLISH
Check of the measurement results
1
Select the items.
The measurement results of each item can be checked here.
A.Set SpConf.Ck
(Remote control unit)
2
Press the ENTER button and display the verification screen.
[Speaker Config. Check]
[Delay Time Check]
[Channel Level Check]
(Remote control unit)
NOTE:
• When measurements have been made using the measurement microphone, speakers with a built-in
filter such as subwoofers might be set with a value that differs from the physical distance because of
the internal electrical delay.
3
If the check ends, press the ENTER button again.
(Remote control unit)
4
Select from
results.
• Store :
• Retry :
• Cancel :
(Remote control unit)
5
Set with the checked measurement value.
Perform the measurement again.
Cancel the checked measurement value.
A.Set
<Store
When the “Store” is selected, all parameters are stored up and
switch to the SUBWOOFER MODE setting.
(Remote control unit)
24
the following three items based on the measurement
ENGLISH
Setting the type of speakers
• Set up in function of your speaker systems. Performing this setup optimizes the system.
• The composition of the signals output to the different channels and the frequency response are adjusted automatically according to the
combination of speakers actually being used.
1
Set whether or not speakers are connected and, if so, their size
parameters.
• To select the speaker
Front Sp.
Center Sp.
Front Sp.
Subwoofer
Listening position
Surround Sp.
Surround Sp.
Surround back Sp.
• To select the parameter
2 FRONT
2
Press the ENTER or
setting.
LARGE
(down) button to enter the settings and switch to the SPEAKER DISTANCE
• Parameters
Large...................Select this when using speakers that have sufficient performance for reproducing bass sound below the frequency set for
the Crossover Frequency mode.
Small...................Select this when using speakers that do not have sufficient performance for reproducing bass sound below the frequency set
for the Crossover Frequency mode. When this is set, bass sound with a frequency below the frequency set for the Crossover
Frequency mode is sent to the subwoofer.
None……............Select this when no speakers are installed.
Yes/No….............Select “Yes” when a subwoofer is installed, “No” when a subwoofer is not installed.
2spkrs/1spkr .......Set the number of speakers to be used for the surround back channel.
If the subwoofer has sufficient low frequency playback capacity, good sound can be achieved even when “Small” is set for the front, center
and surround speakers.
25
ENGLISH
Setting the delay time
• Input the distance between the listening position and the different speakers to set the delay time for the surround mode.
Preparations:
Measure the distances between the listening position and the speakers (L1 to L5) on the diagram at the
right).
L1: Distance between center speaker and listening position
L2: Distance between front speakers and listening position
L3: Distance between surround speakers and listening position
L4: Distance between surround back speaker and listening position
L5: Distance between subwoofer and listening position
FL
Subwoofer
L1
FR
L2
L5
L3
SL
CAUTION:
Please note that the difference for every speaker should be 15 ft or less.
Center
SBL
Listening position
L4
SR
SBR
NOTES:
• No setting when “None” has been selected for the Speaker Configuration setting.
• Surround back is not displayed when ZONE 2 is set with the POWER AMP ASSIGN setting.
1
Select the speaker to be set.
8 FRONT L
12ft
2
Set the distance between the speaker and listening position.
The distance changes in units of 1 foot (0.1 meters) each time the button is pressed. Select the value closest
to the measured distance.
3
Press the ENTER or
26
(down) button to enter the setting and switch the SUBWOOFER MODE setting.
ENGLISH
Setting the Subwoofer mode and Crossover Frequency
This screen is not displayed when not using a subwoofer.
• Set the crossover frequency and subwoofer mode according to the speaker system being used.
1
Select the “Subwoofer Mode”.
2
Select the “Crossover Frequency”
mode.
Select the setting.
16SW MODE NORM
Select the frequency.
17CR.OVER 80Hz
• 40 / 60 / 80 / 100 / 120 / 150 / 200 /
250 Hz can be selected.
3
Press the ENTER or
(down) button to enter the setting and switch to the Test Tone setting.
NOTES:
— Assignment of low frequency signal range —
• The signals produced from the subwoofer channel are LFE signals (during playback of Dolby Digital or DTS signals) and the low frequency
signal range of channels set to “SMALL” in the setup. The low frequency signal range of channels set to “LARGE” are produced from
those channels.
— Crossover Frequency —
• When “Subwoofer” is set to “Yes” at the “Speaker Configuration Setting”, set the frequency (Hz) below which the bass sound of the
various speakers is to be output from the subwoofer (the crossover frequency).
• For speakers set to “Small”, sound with a frequency below the crossover frequency is cut, and the cut bass sound is output from the
subwoofer instead.
NOTE: For ordinary speaker systems, we recommend setting the crossover frequency to 80 Hz. When using small speakers, however,
setting the crossover frequency to a high frequency may improve frequency response for frequencies near the crossover
frequency.
— Subwoofer mode —
• The subwoofer mode setting is only valid when “Large” is set for the front speakers and “YES” is set for the subwoofer in the “Speaker
Configuration” settings (see page 25).
• When the “LFE+MAIN” playback mode is selected, the low frequency signal range of channels set to “Large” are produced
simultaneously from those channels and the subwoofer channel.
In this playback mode, the low frequency range expand more uniformly through the room, but depending on the size and shape of the
room, interference may result in a decrease of the actual volume of the low frequency range.
• Selection of the “LFE ” play mode will play the low frequency signal range of the channel selected with “Large” from that channel only.
Therefore, the low frequency signal range that are played from the subwoofer channel are only the low frequency signal range of LFE
(only during Dolby Digital or DTS signal playback) and the channel specified as “Small” in the setup menu.
• Select the play mode that provides bass reproduction with quantity.
• When the subwoofer is set to “Yes”, bass sound is output from the subwoofer regardless of the subwoofer mode setting in surround
modes other than Dolby/DTS.
• In surround modes other than Dolby Digital and DTS, if the subwoofer is set to “YES”, the low frequency portion is always output to the
subwoofer channel. For details, refer to “Surround Modes and Parameters” on page 60.
27
ENGLISH
Setting the Test Tone
• Use this setting to adjust to that the playback level between the different channel is equal.
• From the listening position, listen to the test tones produced from the speakers to adjust the level.
• The level can also be adjusted directly from the remote control unit. (For details, see page 48.)
1
• Use the
(left) button to the Test Tone.
• Press the ENTER or
Assignment.
(down) button to switch to the Digital In
18 T.TONE
2
<YES
Set the mode.
Select “Auto” or “Manual”.
T.TONE
AUTO
• Auto:
Adjust the level while listening to the test tones produced
automatically from the different speakers.
• Manual:
Select the speaker from which you want to produce the test tone
to adjust the level.
3
4
Press the
(down) button to start Test Tone.
a. If the “Auto” mode is selected:
Test tones are automatically emitted from the different speakers.
The test tones are emitted from the different speakers in the following order, at 4-second intervals the
first time and second time around, 2-second intervals the third time around and on:
SB
FL
C
FR
SR
SBR
1spkr
SBL
SL
SW
2spkrs
When the surround back speaker setting is set to “1spkr” for “Speaker Configuration”, this is set to
“SB”.
Use the CURSOR left and right buttons to adjust all the speakers to
the same volume.
The volume can be adjusted between –12 dB and +12 dB in units of
0.5 dB.
b. When the “Manual” mode is selected
Use the CURSOR up and down to select the speaker for which
you want to output test tones, then use the CURSOR left and
right to adjust so that the volume of the test tones from the
various speakers is the same.
5
6
28
Example: When the volume is set to
–11.5 dB while the Front Lch
speaker is selected
After completing the adjustment, press the ENTER button.
Press the ENTER or
(down) button to enter the setting and switch the DIGITAL input setting.
ENGLISH
NOTES:
• When you adjust the channel levels while in the TEST TONE mode, the channel level adjustments made will affect all surround modes.
Consider this mode a Master Channel Level adjustment mode.
• You can adjust the channel levels for each of the following surround modes: DIRECT, STEREO, STANDARD (DOLBY/DTS SURROUND),
5/7 CH STEREO, MONO MOVIE, ROCK ARENA, JAZZ CLUB, VIDEO GAME, MATRIX and VIRTUAL.
Setting the Digital In Assignment
• This setting assigns the digital input jacks of the AVR-2105/885 for the different input sources.
1
Select the digital input jack to be assigned to the input source.
• To select the digital input jack
19 COAX
2
• To select the input source
Select “OFF” if nothing is connected.
3
Press the ENTER or
CD
(down) button to enter the setting and switch the Component Video input setting.
NOTE:
• PHONO, TUNER and V. AUX cannot be selected.
Setting the Component In Assignment
• This setting assigns the color difference (component) video input jacks of the AVR-2105/885 for the different input sources.
1
Select the component (Y, PB/CB and PR/CR) video input terminal to
be assigned to the input source.
• Component video terminal selection
23 VIDEO1
2
• Input source selection
Select “OFF” if nothing is connected.
3
Press the ENTER or
DVD
(down) button to enter the setting and switch the Video Input Mode setting.
29
ENGLISH
Setting the Video Input Mode
• Set the input signal to be output from the monitor output terminals.
1
Select the input source to be set.
26 DVD
2
3
AUTO:
AUTO
Select the mode (input signal).
Press the ENTER or
(down) button to switch the Auto Surround Mode setting.
When there are multiple input signals, the input signals are detected and the input signal to be output from the video monitor output
terminal is selected automatically in the following order: component video, S-Video, composite video.
Component: The signal connected to the component video terminal is always played.
Video conversion is not conducted, so no image is output from the monitor output terminal when there is no input signal to the
component terminal.
S-Video:
The signal connected to the S-Video terminal is always played.
The S-Video input signal is converted and output from the composite and component monitor output terminal.
Video:
The signal connected to the composite video terminal is always played.
The composite video input signal is up-converted and output from the S-Video and component monitor output terminals.
30
ENGLISH
Setting the Auto Surround Mode
For the three kinds of input signals as shown below, the surround mode played the last is stored in the memory. At next time it the same signal
inputs, the memorized surround mode is automatically selected and the signal is played.
Note that the surround mode setting is also stored separately for the different input function.
1
SIGNAL
Default Auto Surround Mode
q
Analog and PCM 2-channel signals
STEREO
w
2-channel signals of Dolby Digital, DTS or other multichannel format
Dolby PLIIx Cinema
e
Multichannel signals of Dolby Digital, DTS or other multichannel format
Dolby or DTS Surround
Select “ON” if you want to use the auto surround mode, “OFF” if
you do not want to use it.
31 AUTOSURR. ON
2
Press the ENTER or
(down) button to switch the Ext. In SW Level setting.
Setting the Ext. In SW Level
Set the playback level of the analog input signal connected to the Ext. In terminal.
1
Select desired setting.
• Select according to the specifications of the player being used.
Also refer to the player’s operating instructions.
• +15dB (default) recommended. (0, +5, 10 and +15 can be
selected.)
32 EXT.IN SW+15
2
Press the ENTER or
(down) button to switch the Power Amp Assignment setting.
31
ENGLISH
Power Amp Assignment
Setting the power amplifier assignment
• Make this setting to switch the power amplifier for the surround back channel to ZONE2.
• If ZONE2 is selected, the signal that selected at ZONE2 is output at “SURR. BACK/ZONE2” PREOUT terminals.
1
Select “Surround Back” to use as the surround back channel,
“Zone2” to use as Zone 2 out.
33 AMP
2
Press the ENTER or
S.BACK
(down) button to switch the On Screen Display setting.
Setting the On Screen Display (OSD)
• Use this to turn the on-screen display (messages other than the menu screens) on or off.
• Sets the on-screen display’s display mode.
Mode 1: Prevents flickering of the on-screen display when there is no video signal.
Mode 2: Flickering is not prevented.
Use this mode if the on-screen display does not appear in the mode 1, as may happen according to the TV being used.
1
Select “ON” or “OFF”.
34 OSD
2
ON
Select the On Screen Display Mode.
35 OSD
Select the “MODE1” or “MODE2”.
3
32
Press the ENTER or
(down) button to switch the Auto Preset Memory setting.
MODE1
ENGLISH
Auto Tuner Presets
Use this to automatically search for FM broadcasts and store up to 56 stations at preset channels A1 to 8, B1 to 8, C1 to 8, D1 to 8, E1 to 8, F1
to 8 and G1 to 8.
NOTE:
• If an FM station cannot be preset automatically due to poor reception, use the “Manual tuning” operation to tune in the station, then preset it
using the manual “Preset memory” operation.
1
Use the CURSOR button to select “Yes”.
“Search” flashes on the screen and searching begins.
“Completed” appears once searching is completed.
The display automatically switches to screen.
36 PRESET <YES
2
Press the ENTER or
(down) button if you want to start the settings over from the beginning.
After setting up the system
1
Press the SYSTEM SETUP button to finish system set up.
This completes the system setup operations. Once the system is set up, there is no need to make the settings again unless other components
or speakers are connected to or the speaker layout is changed.
• On-screen display signals
Signals input to the AVR-2105/885
On-screen display signal output
VIDEO signal input jack
(yellow)
S-video signal input jack
Video signal output to VIDEO
MONITOR OUT jack (yellow)
Video signal output to SVideo MONITOR OUT jack
Video signal output to Color Difference
(Component) Video MONITOR OUT jack
1
E
E
C
C
C
2
C
E
C
C
C
3
E
C
C
C
C
4
C
C
E
C
C
(C: Signal
E: No signal)
(C: On-screen signals output
E: On-screen signals not output)
NOTE:
• When a component video signal is input and when the “Video Input Mode” is set to the component fixed mode at Input setup, the onscreen display is only displayed when the System Setup, Surround Parameters and On Screen buttons are operated.
33
ENGLISH
9 REMOTE CONTROL UNIT
Operating DENON audio components
• Turn on the power of the different components before operating them.
1
Set mode switch 1 to “AUDIO”.
2
Set mode switch 2 to the position for the component to be
operated. (CD, CDR/MD or Tape deck)
3
1
2
3
3
Operate the audio component.
• For details, refer to the component’s operating instructions.
While this remote control is compatible with a wide range of infrared controlled components, some models of components may not
be operated with this remote control.
1. CD player (CD) and CD recorder and MD recorder
(CDR/MD) system buttons
6, 7
:
:
1
:
8, 9 :
3
:
DISC
:
SKIP+
2
2. Tape deck (TAPE) system buttons
Manual search (forward and reverse)
Stop
Play
Auto search (cue)
Pause
Switch discs
(for CD changers only)
:
:
2
:
1 :
0 :
A/B :
6
7
Rewind
Fast-forward
Stop
Forward play
Reverse play
Switch between decks A and B
3. Tuner system buttons
SHIFT
CHANNEL
+, –
TUNING
+, –
BAND
MODE
MEMORY
NOTE:
• TUNER can be operated when the switch is at “AUDIO” position.
34
: Switch preset channel range
: Preset channel
up/down
: Frequency
up/down
: Switch between the AM and FM bands
: Switch between auto and mono
: Preset memory
ENGLISH
Preset memory
DENON and other makes of components can be operated by setting the preset memory.
This remote control unit can be used to operate components of other manufacturers by registering the
manufacturer of the component as shown on the List of Preset Codes (pages 144~148).
Operation is not possible for some models.
1
Set mode switch 1 to “AUDIO” or “VIDEO”.
Set the AUDIO side for the CD, Tape deck or CDR/MD
position, to the VIDEO side for the DVD/VDP, DBS/CABLE,
VCR or TV position.
2
Set mode switch 2 to the component to be registered.
3
Press the ON/SOURCE button and the OFF button at the
same time.
3
4
1
2
• Indicator flash.
4
1
2
3
4
5
6
7
8
9
Referring to the included List of
Preset Codes, use the number
buttons to input the preset code (a 3digit number) for the manufacturer of
the component whose signals you
want to store in the memory.
0
5
To store the codes of another component in the memory,
repeat steps 1 to 4.
NOTES:
• The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control
unit’s transmitting window while setting the preset memory.
• Depending on the model and year of manufacture, this function cannot be used for some models, even if they are of makes listed on the
included list of preset codes.
• Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and
check.
• The preset memory can be set for one component only among the following: CDR/MD, DVD/VDP and DBS/CABLE.
The preset codes are as follows upon shipment from the factory and after resetting:
TV, VCR.....................................................HITACHI
CD, TAPE ..................................................DENON
CDR/MD ...................................................DENON (CDR)
DVD/VDP ..................................................DENON (DVD)
DBS/CABLE ..............................................ABC (CABLE)
35
ENGLISH
Operating component stored in the preset memory
1
Set mode switch 1 to “AUDIO” or “VIDEO”.
Set the AUDIO side for the CD, tape deck or CDR/MD
position, to the VIDEO side for the DVD/VDP, DBS/CABLE,
VCR or TV position.
2
3
3
Set mode switch 2 to the component you want to operate.
1
3
3
Operate the component.
• For details, refer to the component’s operating instructions.
Some models cannot be operated with this remote control unit.
1. Digital video disc player (DVD)
system buttons
2. Video disc player (VDP) system
buttons
POWER : Power on/standby
(ON/SOURCE)
OFF
: DENON DVD Power off
6,7 : Manual search
(forward and reverse)
2
: Stop
1
: Play
8,9 : Auto search
(to beginning of track)
3
: Pause
0 ~ 9, +10 : 10 key
DISC SKIP +: Disc skip
(for DVD changer only)
DISPLAY : Switch display
MENU : Menu
RETURN : Return
SETUP : Setup
•, ª, 0, 1 : Cursor up, down, left and right
ENTER : Enter setting
POWER
: Power on/standby
(ON/SOURCE)
6,7
: Manual search
(forward and reverse)
2
: Stop
1
: Play
8,9
: Auto search (cue)
3
: Pause
0~9, +10
: 10 key
NOTE:
• Some manufacturers use different
names for the DVD remote control
buttons, so also refer to the
instructions on remote control for
that component.
36
2
ENGLISH
3. Video deck (VCR) system buttons
POWER
: Power on/standby
(ON/SOURCE)
6,7
: Manual search
(forward and reverse)
2
: Stop
1
: Play
3
: Pause
Channel +, – : Channels
4. Digital broadcast satellite (DBS)
tuner and cable (CABLE) system
buttons
POWER
:
(ON/SOURCE)
MENU
:
RETURN
:
•, ª, 0, 1 :
ENTER
:
CHANNEL
:
+, –
0~9, +10
:
DISPLAY
:
VOL +, –
:
Power on/standby
Menu
Return
Cursor up, down, left and right
Enter
Switch channels
Channels
Switch display
Volume up/down
5. Monitor TV (TV) system buttons
POWER
:
(ON/SOURCE)
MENU
:
RETURN
:
•, ª, 0, 1 :
ENTER
:
CHANNEL
:
+, –
0~9, +10
:
DISPLAY
:
TV/VCR
:
TV VOL
+, –
Power on/standby
Menu
Return
Cursor up, down, left and right
Enter
Switch channels
Channels
Switch display
Switch between TV
and video player
: Volume up/down
NOTES:
• For this CD, CDR, MD and TAPE components, buttons can be operated in the same way as for Denon audio components (page 34).
• The TV can be operated when the switch is at DVD/VDP, VCR, TV position.
37
ENGLISH
Punch Through
• “Punch Through” is a function allowing you to operate the PLAY, STOP, MANUAL SEARCH and AUTO SEARCH buttons on the CD, TAPE,
CDR/MD, DVD/VDP or VCR components when in the DBS/CABLE or TV mode. By default, nothing is set.
1
Set mode switch 1 to “VIDEO”.
2
Set mode switch 2 to the component to be registered
(DBS/CABLE or TV).
3
4
1
3
Press the OFF (ZONE2) button and the ON (MAIN) button at
the same time.
• Indicator flash.
4
1
2
3
4
5
6
7
8
9
Input the number of the component
you want to set. (See Table 1)
Table 1
0
38
CD
TAPE
CDR/MD
DVD/VDP
VCR
No setting
No.
1
2
3
4
5
0
3
2
ENGLISH
10 OPERATION
Before operating
Preparations:
Check that all connections are proper.
1
2 1
Press the Power switch (button).
ON
OFF
(Main unit)
3
• ¢ ON
The power turns on and indicator is light.
Set the power switch to this position to turn the power on
and off from the included remote control unit.
• £ OFF
The power turns off and indicator is off.
In this position, the power cannot be turned on and off from
the remote control unit.
2
2
Turn on the power.
Press the Power ON/STANDBY switch (button).
ON / STANDBY
(Main unit)
(Remote control unit)
When pressed, the power turns on and the display lights. The
sound is muted for several seconds, after which the unit
operates normally. When pressed again, the power turns off,
the standby mode is set and the display turns off.
3
3
Select the front speakers.
Press the SPEAKER A or B button to turn the speaker on.
SPEAKER
A
B
(Main unit)
(Remote control unit)
• The front speaker A, B setting can be also be changed with
the SPEAKER button on the remote control unit.
39
ENGLISH
Playing the input source
1 1
2
5
3
1
3
5
1
Select the input source to be played.
Example: CD
FUNCTION
(Main unit)
(Remote control unit)
To select the input source when
ZONE2/REC OUT is selected, press
the MAIN button then operate the
input function selector.
MAIN
(Main unit)
2
Select the input mode.
• Selecting the analog mode
Press the ANALOG button to switch to the analog input.
ANALOG
(Main unit)
(Remote control unit)
• Selecting the external input (EXT. IN) mode
Press the EXT. IN to switch the external input.
EXT. IN
(Main unit)
(Remote control unit)
• Selecting the AUTO, PCM and DTS modes
The mode switches as shown below each time the INPUT
MODE button is pressed.
AUTO
PCM
DTS
40
Input mode selection function
Different input modes can be selected for the different input sources.
The selected input modes for the separate input sources are stored in
the memory.
q AUTO (auto mode)
In this mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected and
the program in the AVR-2105/885’s surround decoder is selected
automatically upon playback. This mode can be selected for all
input sources other than PHONO and TUNER.
The presence or absence of digital signals is detected, the signals
input to the digital input jacks are identified and decoding and
playback are performed automatically in DTS, Dolby Digital or PCM
(2 channel stereo) format. If no digital signal is being input, the
analog input jacks are selected.
Use this mode to play Dolby Digital signals.
w PCM (exclusive PCM signal playback mode)
Decoding and playback are only performed when PCM signals are
being input.
Note that noise may be generated when using this mode to play
signals other than PCM signals.
e DTS (exclusive DTS signal playback mode)
Decoding and playback are only performed when DTS signals are
being input.
r ANALOG (exclusive analog audio signal playback mode)
The signals input to the analog input jacks are decoded and played.
t EXT. IN (external decoder input jack selection mode)
The signals being input to the external decoder input jacks are
played without passing through the surround circuitry.
NOTE:
• Note that noise will be output when CDs or LDs recorded in DTS
format are played in the “PCM” (exclusive PCM signal playback) or
“ANALOG” (exclusive PCM signal playback) mode. Select the
AUTO or DTS mode when playing signals recorded in DTS.
INPUT MODE
(Main unit)
2
(Remote control unit)
Notes on playing a source encoded with DTS
• Noise may be generated at the beginning of playback and
while searching during DTS playback in the AUTO mode. If
so, play in the DTS mode.
• In some rare cases the noise may be generated when you
preform the operation to stop playback of a DTS-CD or DTS-LD.
ENGLISH
3
Select the play mode.
Press the SURROUND MODE button, then turn the SELECT
knob.
Input mode display
One of these lights, depending on the
input signal.
• In the AUTO mode
INPUT
PCM
AUTO
DTS
DIGITAL
Example: Stereo
ANALOG
• In the DIGITAL PCM mode
SURROUND
MODE
INPUT
PCM
SELECT
AUTO
DTS
DIGITAL
• In the DIGITAL DTS mode
(Main unit)
(Remote control unit)
INPUT
PCM
AUTO
DTS
DIGITAL
To select the surround mode while
adjusting the surround parameters,
tone defeat or tone control, press
the surround mode button then
operate the selector.
SURROUND
MODE
INPUT
PCM
AUTO
DTS
ANALOG
(Main unit)
4
5
• In the ANALOG mode
Start playback on the selected component.
• For operating instructions, refer to the component’s manual.
Input signal display
• DOLBY DIGITAL
SIGNAL
DIGITAL
Adjust the volume.
• DTS
SIGNAL
MASTER VOLUME
DIGITAL
• PCM
The volume level is
displayed on the
master volume level
display.
SIGNAL
DIGITAL
(Main unit)
(Remote control unit)
The volume can be adjusted within the range of –70 to 0
to 18 dB, in steps of 0.5 dB. However, when the channel
level is set as described on page 48, if the volume for any
channel is set at +0.5 dB or greater, the volume cannot be
adjusted up to 18 dB. (In this case the maximum volume
is adjusted to “18 dB — (Maximum value of channel
level)”.)
Input mode when playing DTS sources
• Noise will be output if DTS-compatible CDs or LDs are played in the
“ANALOG” or “PCM” mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to “DTS”.
The DIGITAL indicator lights when digital signals are being input
properly. If the DIGITAL indicator does not light, check whether
the digital input component setup (page 29) and connections are
correct and whether the component’s power is turned on.
NOTE:
• The DIGITAL indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
41
ENGLISH
Playback using the external input (EXT. IN) jacks
1
Set the external input (EXT.
IN) mode.
Press the EXT. IN button to
switch the external input.
2 1
EXT. IN
(Main unit)
(Remote control unit)
Once this is selected, the input signals connected to the FL
(front left), FR (front right), C (center), SL (surround left) and
SR (surround right) channels of the EXT. IN jacks are output
directly to the front (left and right), center and surround (left
and right) speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer) jack is
output to the PRE OUT SUBWOOFER jack.
2
Cancelling the external input mode
To cancel the external input (EXT. IN) setting, press the INPUT
MODE (AUTO, PCM, DTS) or ANALOG button to switch to
the desired input mode. (See page 40.)
INPUT MODE
ANALOG
(Main unit)
(Remote control unit)
• When the input mode is set to the external input (EXT. IN), the play
mode (DIRECT, STEREO, STANDARD (DOLBY/DTS SURROUND),
5CH/7CH STEREO or DSP SIMULATION) cannot be selected.
2
1
NOTES:
• In play modes other than the external input mode, the signals
connected to EXT. IN jacks cannot be played. In addition, signals
cannot be output from channels not connected to the input
jacks.
• The external input mode can be set for any input source. To
watch video while listening to sound, select the input source to
which the video signal is connected, then set this mode.
• If the subwoofer output level seems to high, set the “SW ATT.”
surround parameter to “ON”.
Playing audio sources (CDs and DVDs)
The AVR-2105/885 is equipped with two 2-channel playback modes exclusively for music.
Select the mode to suit your tastes.
1
DIRECT mode
Use this mode to achieve good quality 2channel sound while watching images. In
this mode, the audio signals bypass such
circuits as the tone circuit and are
transmitted directly, resulting in good
quality sound.
DIRECT /
STEREO
(Main unit)
1, 2
(Remote control unit)
2
STEREO mode
Use this mode to adjust the tone and
achieve the desired sound while watching
images.
DIRECT /
STEREO
1
(Main unit)
(Remote control unit)
42
2
ENGLISH
After starting playback
[1] Adjusting the sound quality (tone)
The tone control function will not work in the direct mode.
1
The tone switches as follows each time the TONE CONTROL
button is pressed.
TONE
CONTROL
BASS
TREBLE
(Main unit)
2
With the name of the volume to be
adjusted selected, turn the SELECT
knob to adjust the level.
2 31
SELECT
3
(Main unit)
If you do not want the bass and treble to be adjusted, turn on
the tone defeat mode.
• To increase the bass or treble: Turn the control clockwise.
(The bass or treble sound can be increased to up to +6 dB
in steps of 1 dB.)
• To decrease the bass or treble: Turn the control
counterclockwise. (The bass or treble sound can be
decreased to up to –6 dB in steps of 1 dB.)
TONE
DEFEAT
The signals do not pass through the
bass and treble adjustment circuits,
so it provides higher quality sound.
(Main unit)
[2] Listening over headphones
1
Plug the headphones’ plug into the jack.
PHONES
Connect the headphones to the
PHONES jack.
The pre-out output (including the
speaker output) is automatically
turned off when headphones are
connected.
NOTE:
To prevent hearing loss, do not raise the volume level excessively
when using headphones.
1
[3] Turning the sound off temporarily (muting)
1
Use this to turn off the audio output
temporarily.
Press the MUTING button.
1
Cancelling MUTING mode.
• Press the MUTING button again.
• Muting will also be cancelled
when MASTER VOL is adjusted
up or down.
[4] Combining the currently playing sound with the desired image
1
Simulcast playback
Use this switch to monitor a video source
other than the audio source.
Press the VIDEO SELECT button repeatedly
until the desired source appears on the
display.
Cancelling simulcast playback.
• Select “SOURCE” using the video
select button.
• Switch the program source to the
component connected to the video
input jacks.
1
VIDEO SELECT
(Main unit)
1
1
(Remote control unit)
Display
IN=V SOURCE
43
ENGLISH
[5] Checking the currently playing program source, etc.
1
On screen display
• Each time an operation is performed, a
description of that operation appears on
the display connected to the unit’s
VIDEO MONITOR OUT jack. Also, the
unit’s operating status can be checked
(Remote control unit)
during playback by pressing the remote
control unit’s ON SCREEN/DISPLAY
button.
Such information as the position of the input selector and
the surround parameter settings is output in sequence.
Front panel display
• Descriptions of the unit’s operations are
also displayed on the front panel display.
In addition, the display can be switched
to check the unit’s operating status
while playing a source by pressing the
STATUS button.
2
Using the dimmer function
• Use this to change the brightness of the
display.
The display brightness changes in four
steps (bright, medium, dim and off) by
pressing the main unit’s DIMMER
button repeatedly.
BRIGHT
MEDIUM
2 1
STATUS
1
2
(Main unit)
DIMMER
(Main unit)
DIM
OFF
(Remote control unit)
Multi-source recording
Playing one source while recording another (REC OUT mode)
1
Press the ZONE2/REC SELECT button.
The display switches as follows each time
the button is pressed.
ZONE2
2
REC
With “RECOUT SOURCE” displayed, turn
the FUNCTION knob to select the source
you wish to record.
2, 4 1
2
ZONE 2 /
REC SELECT
(Main unit)
FUNCTION
(Main unit)
3
Set the recording mode.
• For operating instructions, refer to the manual of the
component on which you want to record.
4
To cancel, turn the function knob and
select “SOURCE”.
REC
PHONO CD TUNER
DVD / VDP TV / DBS
VCR
-1 -2
V.AUX CDR / TAPE
RECOUT
SOURCE
FUNCTION
(Main unit)
44
2
Display
NOTES:
• Recording sources other than digital inputs selected in the REC
OUT mode are also output to the ZONE2 audio output jacks.
• Digital signals are not output to the REC SOURCE or audio
output jacks.
• The DIGITAL IN’s signal selected with the function selector knob
are output to the DIGITAL OUT (OPTICAL) jack.
ENGLISH
11 MULTI ZONE
Multi-zone playback with multi-source
MULTI ZONE MUSIC ENTERTAINMENT SYSTEM
• When the outputs of the “ZONE2” OUT terminals are wired and connected to integrated amplifiers installed in other rooms, different sources
can be played in rooms other than the main zone in which this unit and the playback devices are installed. (Refer to ZONE2 on the diagram
below.)
• ZONE 2 SPEAKER OUT and PRE OUT can be used when “ZONE2” is selected at System Setup Menu “Power Amp Assignment”. In this case,
Surround Back Speaker Out cannot be used for MAIN ZONE.
• When a sold separately room-to-room remote control unit (DENON RC-616, 617 or 618) is wired and connected between the main zone and
zone2, the remote-controllable devices in the main zone can be controlled from zone2 using the remote control unit.
NOTES:
• For the AUDIO outputs, use high quality pin-plug cords and wire in such a way that there is no humming or noise.
• For instructions on installation and operation of separately sold devices, refer to the devices’ operating instructions.
• When the main unit is set to the recording output mode, zone2 remote control key cannot be operated.
MULTI ROOM MUSIC ENTERTAINMENT SYSTEM
2 When using the SURR.BACK/ZONE2 amplifier as the SURROUND BACK.
• 7.1-channel playback using the surround back speaker is possible in the MAIN ZONE.
• To use the ZONE2 line output, turn on the ZONE2 button (remote control unit).
• The ZONE2 OUT terminal’s output level cannot be adjusted with the remote control unit.
System configuration and connections example.
Using external amplifier
MAIN ZONE 7.1-channel systems
Monitor
FL
ZONE 2
FR
Center
This unit
DVD player
B
SW
B
Input
RC-617
Premain Amplifier
or Power Amplifier
ZONE2 AUDIO OUT
(FIXED OUT)
SL
SR
RC-616
SBL
SBR
PROGRAMMABLE
REMOTE CONTROL UNIT
SYSTEM REMOTE CONTROL
UNIT RC-980
ROOM-TO-ROOM REMOTE CONTROL SYSTEM
(separately sold) control line
MULTI SOURCE AUDIO signal cable
* Refer to CONNECTIONS on pages 7 to 15.
45
ENGLISH
2 When using the SURR.BACK/ZONE2 amplifier as the ZONE2.
• The SPEAKER OUT, LINE OUT and PRE OUT terminals can be used simultaneously in ZONE2.
• To use the ZONE2, turn on the ZONE2 button (remote control unit).
• The output of the ZONE2 SPEAKER OUT & SRB/Z2 RCA terminals can be adjusted with the remote control unit’s ZONE2 VOLUME + and – buttons.
System configuration and connections example.
Using this unit’s internal amplifier as the ZONE2.
MAIN ZONE 5.1-channel systems
Monitor
FL
ZONE 2
FR
C
This unit
DVD player
B
SW
Input
RC-617
ZONE2 SPEAKER OUT
SL
RC-616
SR
SYSTEM REMOTE
CONTROL UNIT RC-980
PROGRAMMABLE
REMOTE CONTROL UNIT
ROOM-TO-ROOM REMOTE CONTROL SYSTEM
(separately sold) control line
MULTI SOURCE AUDIO signal cable
SPEAKER cable
* Refer to CONNECTIONS on pages 7 to 15.
46
ENGLISH
Multi-source playback
[1] Outputting a program source to an amplifier, etc., in a different room (ZONE2 mode)
1
Press the ZONE2/REC SELECT button.
The display switches as follows each
time the button is pressed.
2, 4 1
2
ZONE 2 /
REC SELECT
(Main unit)
2
With “ZONE2 SOURCE” displayed, turn
the FUNCTION knob and select the source
you wish to record.
FUNCTION
(Main unit)
3
Start playing the source to be output.
• For operating instructions, refer to the manuals of the
respective components.
4
To cancel, turn the function knob and
select “SOURCE”.
2
Display
ZONE2
PHONO CD TUNER
DVD / VDP TV / DBS
VCR
-1 -2
V.AUX CDR / TAPE
ZONE2
SOURCE
FUNCTION
(Main unit)
NOTES:
• The signals of the source selected in the ZONE2 mode are also
output from the VCR-1, VCR-2 and CDR/TAPE recording output
terminals.
• Digital signals are not output to the ZONE2 output jacks.
[2] Remote control unit operations during multi-source playback (selecting the source)
1
Set the slide switch to “AUDIO” and “ZONE2”.
2
OUTPUT
SURROUND
ZONE 2
BACK
(Light)
(Remote control unit)
2
Press the ZONE2 “ON” button.
To cancel the ZONE2 mode.
Press the ZONE2 “OFF” button.
(Remote control unit)
3
4
The main zone output can be
turned on and off with the MAIN
ON/OFF button.
2
Press the input source button.
• The ZONE2 source switches directly.
3
The output level of the ZONE 2 SPEAKER
OUT terminals can be controlled using the
VOLUME + and – buttons on the remote
control unit.
5
1
1
(Remote control unit)
DEFAULT SETTING (ZONE2 VOLUME LEVEL) :
- - - dB (MINIMUM)
5
4
When the ZONE2 SOURCE function is set
to TUNER, the preset channel can be
selected using the CHANNEL + and –
buttons on the remote control unit.
(This is only possible when the main unit
in the ZONE2 mode.)
(Remote control unit)
47
ENGLISH
12 SURROUND
Before playing with the surround function
• Before playing with the surround function, be sure to use the test tones to adjust the playback level from the different speakers. This adjustment
can be performed with the system setup (see page 19) or from the remote control unit, as described below.
• Adjusting with the remote control unit using the test tones is only possible in the “Auto” mode and only effective in the STANDARD
(DOLBY/DTS SURROUND) modes. The adjusted levels for the different modes are automatically stored in the memory.
1
Set the STANDARD (DOLBY/DTS SURROUND) modes.
STANDARD
(Main unit)
2
(Remote control unit)
Press the TEST TONE button.
1
(Remote control unit)
3
1
Test tones are output from the
different speakers. Use the channel
volume adjust buttons to adjust so
that the volume of the test tones is
the same for all the speakers.
(Remote control unit)
4
After completing the adjustment, press
the TEST TONE button again.
(Remote control unit)
3
2, 4
48
3
ENGLISH
• After adjusting using the test tones, adjust the channel levels either according to the playback sources or to suit your tastes, as (described)
below.
1
Select the speaker whose level you want
to adjust.
The channel switches as shown below each time the button
is pressed.
FL
C
FR
SW
SR
SBR
SBL
SL
When the surround back speaker setting is set to
“1sp” for “Speaker Configuration”, this is set to “SB”.
“SB” appears only when “POWER AMP ASSIGN” setting
is SURR. BACK mode.
NOTE: Please make sure the “AUDIO” position of the slide
switch on the remote control unit.
2
Adjust the level of the selected
speaker.
2
2
1
Default setting of channel level is 0 dB.
The level of the selected speaker can be adjusted within
the range of +12 to –12 dB using the cursor buttons.
SW channel level can be turned off by decreasing one step
from –12 dB.
OFF ´ –12 dB ´ +12 dB
49
ENGLISH
Dolby Pro Logic IIx (Pro Logic II) mode
To play in the PL IIx mode, set “S. BackSp” at the Speaker Configuration setting to “1Sp” or “2Sp”.
To play in the PL IIx mode, set “Surround Back” at the Power Amp Assign setting.
2
The Dolby Surround Pro Logic
IIx Cinema or Music mode can
be chosen directly by pressing
the CINEMA or MUSIC button
on the remote control unit
during playback in the Dolby
Surround Pro Logic IIx mode.
1
1
1
2
4, 6 5, 7
Select the function to which the component you want to play
is connected.
Example: DVD
FUNCTION
(Main unit)
2
(Remote control unit)
9
5, 7
STANDARD
(Remote control unit)
• The Dolby Pro Logic II indicator lights.
Display
Light
LOGICII
3
4
Play a program source with the
mark.
• For operating instructions, refer to the manuals of the respective components.
SURROUND
PARAMETER
Select the surround parameter mode.
Display
(Main unit)
To perform this operation from the remote control unit, check that
the mode selector switch is set to “AUDIO”.
(Remote control unit)
50
5, 7
6
Select the Dolby Surround Pro Logic IIx mode.
(Main unit)
6
4
ENGLISH
5
Select the optimum mode for the source.
• When the “SB CH OUT” parameter is set to “ON”. (Set “S. BACK” at system set up to
“SMALL” or “LARGE”.)
SELECT
(Main unit)
(Pro Logic IIx
Cinema mode)
(Remote control unit)
(Pro Logic IIx
Music mode)
or
(Pro Logic IIx
Game mode)
or
• When the “SB CH OUT” parameter is set to “OFF”. (Set “S. BACK” at system set up to
“NONE”.)
(Pro Logic II
Cinema mode)
(Pro Logic II
Music mode)
or
6
(Dolby Pro Logic
mode)
(Pro Logic II
Game mode)
or
Select the various parameters. (See “Surround parameters q” for a description of the various parameters.)
SURROUND
PARAMETER
(Main unit)
7
(Remote control unit)
Set the various surround parameters.
SELECT
(Main unit)
8
9
(Remote control unit)
(Remote control unit)
When the surround parameters are set using the buttons on the main unit, stop operating buttons after completing the settings. The
settings are automatically finalized and the normal display reappears after several seconds.
Press the ENTER button to finish surround parameter mode.
(Remote control unit)
NOTE:
• When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and
the setting will be completed.
51
ENGLISH
DTS NEO:6 mode
2
The DTS NEO:6 Cinema or
Music mode can be chosen
directly by pressing the CINEMA
or MUSIC button on the remote
control unit during playback in
the DTS NEO:6 mode.
1
1
1
2
4, 6 5, 7
Select the function to which the component you want to play
is connected.
Example: DVD
FUNCTION
(Main unit)
2
(Remote control unit)
STANDARD
(Main unit)
(Remote control unit)
• The mode switches as shown below each time the button
is pressed.
3
4
DTS NEO:6
Play a program source.
Select the surround parameter mode.
Display
SURROUND
PARAMETER
(Main unit)
MODE
cinema
(Remote control unit)
To perform this operation from the remote control unit,
check that the mode selector switch is set to “AUDIO”.
52
5, 7
6
Select the DTS NEO:6 mode.
DOLBY PLIIx
9
5, 7
6
4, 6
ENGLISH
5
Surround parameters q
Select the optimum mode for the source.
SELECT
(Main unit)
MODE
(Remote control unit)
cinema
MODE
or
6
music
or
Select the various parameters.
SURROUND
PARAMETER
(Main unit)
7
(Remote control unit)
(Remote control unit)
Set the various surround parameters.
SELECT
(Main unit)
(Remote control unit)
8
When the surround parameters are set using the buttons on
the main unit, stop operating buttons after completing the
settings. The settings are automatically finalized and the
normal display reappears after several seconds.
9
Press the ENTER button to finish
surround parameter mode.
Pro Logic IIx and Pro Logic II Mode:
• The Cinema mode is for use with stereo television shows and
all programs encoded in Dolby Surround.
• The Music mode is recommended as the standard mode for
auto sound music systems (no video), and is optional for A/V
systems.
• The Pro Logic mode offers the same robust surround
processing as original Pro Logic in case the source contents is
not of optimum quality.
• The Game mode for playing games.The game mode can only be
used with 2-channel audio sources.
Select one of the modes (“Cinema”, “Music”, “Pro Logic” or
“Game”).
Panorama Control:
This mode extends the front stereo image to include the
surround speakers for an exciting “wraparound” effect with
side wall imaging.
Select “OFF” or “ON”.
Dimension Control:
This control gradually adjust the soundfield either towards the
front or towards the rear.
The control can be set in 7 steps from 0 to 6.
Center Width Control:
This control adjust the center image so it may be heard only
from the center speaker; only from the left/right speakers as a
phantom image; or from all three front speakers to varying
degrees.
The control can be set in 8 steps from 0 to 7.
DTS NEO:6 Mode:
• Cinema
This mode is optimum for playing movies. Decoding is
performed with emphasis on separation performance to
achieve the same atmosphere with 2-channel sources as with
6.1-channel sources.
This mode is effective for playing sources recorded in
conventional surround formats as well, because the in-phase
component is assigned mainly to the center channel (C) and the
reversed phase component to the surround (SL, SR and SB
channels).
• Music
This mode is suited mainly for playing music. The front channel
(FL and FR) signals bypass the decoder and are played directly
so there is no loss of sound quality, and the effect of the
surround signals output from the center (C) and surround (SL,
SR and SB) channels add a natural sense of expansion to the
sound field.
CENTER IMAGE (0.0 to 1.0: default 0.3):
The center image parameter for adjusting the expansion of the
center channel in the DTS NEO:6 MUSIC mode has been added.
(Remote control unit)
NOTE:
• When making parameter settings, the display will return to the
regular condition several seconds after the last button was
pressed and the setting will be completed.
53
ENGLISH
Dolby Digital mode (only with digital input) and DTS Surround (only with digital input)
1
Select the input source.
1
1
4
3
Playback with a digital input
q Select an input source set to digital (COAXIAL/OPTICAL)
(see page 29).
Example: DVD
FUNCTION
3 2
2 5, 6 2, 7
(Remote control unit)
(Main unit)
w Set the input mode to “AUTO” or DTS.
INPUT MODE
2
(Main unit)
2
(Remote control unit)
1
Select the STANDARD (Dolby/DTS Surround) mode.
STANDARD
(Main unit)
(Remote control unit)
When performing this operation from the main unit’s panel,
press the SURROUND MODE button, then turn the SELECT
knob and select Dolby Pro Logic IIx or DTS NEO:6.
SURROUND
MODE
SELECT
8
7
6
5, 6
7
3
6
(Main unit)
3
1
(Main unit)
Operate the SURROUND BACK button to switch Surround
Back CH ON/OFF.
SURROUND
BACK
SURROUND
BACK
(Main unit)
Light
(Remote control unit)
• Lights when the SURROUND BACK button is on.
4
Play a program source with the
DIGITAL
Light
Light
54
,
mark.
• The Dolby Digital indicator lights when
playing Dolby Digital sources.
• The DTS indicator lights when playing
DTS sources.
ENGLISH
5
Display the surround parameter menu.
SURROUND
PARAMETER
(Main unit)
6
(Remote control unit)
Select the various parameters.
SURROUND
PARAMETER
(Main unit)
7
(Remote control unit)
(Remote control unit)
Adjust the parameter settings.
SELECT
(Main unit)
8
(Remote control unit)
Press the ENTER button to finish surround parameter mode.
(Remote control unit)
NOTE:
• When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and
the setting will be completed.
2 Dialogue Normalization
The dialogue normalization function is activated automatically when playing Dolby Digital program sources.
Dialogue normalization is a basic function of Dolby Digital which automatically normalizes the dialog level (standard level) of the signals which are
recorded at different levels for different program sources, such as DVD, DTV and other future formats that will use Dolby Digital.
These contents can be verified with the STATUS and ON SCREEN buttons.
Display
OFFSET
- 4dB
The number indicates the normalization level when the currently playing program is normalized to
the standard level.
55
ENGLISH
Checking the input signal
The input signal can be checked by pressing the remote control unit’s ON
SCREEN button.
SIGNAL: Displays the type of signal (DTS, DOLBY DIGITAL, PCM, etc.).
fs:
Displays the input signal’s sampling frequency.
(Remote control unit)
FORMAT: Displays the input signal’s number of channels.
“Number of front channels/Number of surround channels/LFE on/off”
“SURROUND” is displayed for 2-channel signal sources recorded in Dolby Surround.
OFFSET: Displays the dialog normalization offset value.
FLAG:
Displays the special identification signal recorded in the input signal.
“MATRIX” is displayed when matrix processing is conducted on the surround back
channel, “DISCRETE” is displayed when discrete processing is conducted.
Not displayed when no identification signal is recorded.
In addition, screen information is displayed in the following order when the ON SCREEN button is
pressed repeatedly:
OSD-1
OSD-2
OSD-3
OSD-4~10
NOTE:
OSD-3:
Input signal
Input/output
Auto surround mode
Tuner preset stations
This is displayed when the auto surround mode is set to “ON” and the input mode is set to “Auto”.
It is not displayed when the input mode is set to “Analog” or “EXT. IN”.
Surround parameters w
CINEMA EQ. (Cinema Equalizer):
The Cinema EQ function gently decreases the level of the extreme high frequencies, compensating for overly-bright sounding motion
picture soundtracks. Select this function if the sound from the front speakers is too bright.
This function only works in the Dolby Pro Logic IIx, Dolby Digital, DTS Surround and DTS NEO:6 modes. (The same contents are set for all
operating modes.)
D.COMP. (Dynamic Range Compression):
Motion picture soundtracks have tremendous dynamic range (the contrast between very soft and very loud sounds). For listening late at
night, or whenever the maximum sound level is lower than usual, the Dynamic Range Compression allows you to hear all of the sounds in
the soundtrack (but with reduced dynamic range). (This only works when playing program sources recorded in Dolby Digital or DTS.) Select
one of the four parameters (“OFF”, “LOW”, “MID” (middle) or “HI” (high)). Set to OFF for normal listening.
LFE (Low Frequency Effect):
This sets the level of the LFE (Low Frequency Effect) sounds included in the source when playing program sources recorded in Dolby Digital
or DTS.
If the sound produced from the subwoofer sounds distorted due to the LFE signals when playing Dolby Digital or DTS sources when the
peak limiter is turned off with the subwoofer peak limit level setting (system setup menu), adjust the level as necessary.
Program source and adjustment range:
1. Dolby Digital:
–10 dB to 0 dB
2. DTS Surround: –10 dB to 0 dB
When DTS encoded movie software is played, it is recommended that the LFE LEVEL be set to 0 dB for correct DTS playback.
When DTS encoded music software is played, it is recommended that the LFE LEVEL be set to –10 dB for correct DTS playback.
TONE:
This adjusts the tone control. This can be set individually for the separate shroud mode other than Pure direct and direct mode.
SB CH OUT (Surround Back):
(1) (Multi channel source)
“OFF” ..................Playback is conducted without using the surround back speaker.
“NON MTRX”......The same signals those of the surround channels are output from the surround back channels.
“MTRX ON” ........Surround back channel is reproduced using digital matrix processing.
“ES MTRX” .........When playing DTS signals, the surround back signals undergo digital matrix processing for playback.
“ES DSCRT”........When a signal identifying the source as a discrete 6.1-channel source is included in the DTS signals, the surround back
signals included in the source are played.
“PL IIx Cinema” ..Processing is performed with the Cinema mode of the PL IIx decoder and the Surround Back channel is reproduced.
“PL IIx Music” ....Processing is performed with the Music mode of the PL IIx decoder and the Surround Back channel is reproduced.
(2) (2ch source)
“OFF” ..................Playback is conducted without using the surround back speaker.
“ON” ...................Playback is conducted using the surround back speaker.
NOTE: This operation can be performed directly using the SURROUND BACK button on the main unit’s panel.
56
ENGLISH
13 DSP SURROUND SIMULATION
• This unit is equipped with a high performance DSP (Digital Signal Processor) which uses digital signal processing to synthetically recreate the
sound field. One of 7 preset surround modes can be selected according to the program source and the parameters can be adjusted according
to the conditions in the listening room to achieve a more realistic, powerful sound.
Surround modes and their features
1
5CH/7CH
STEREO
The front left channel signals are output to the surround and surround back signal left channels, the front right
channel signals are output to the surround and surround back signal right channels, and the in-phase component
of the left and right channels is output to the center channel. Use this mode to enjoy stereo sound.
2
MONO MOVIE
(NOTE 1)
Select this when watching monaural movies for a greater sense of expansion.
3
ROCK ARENA
Use this mode to achieve the feeling of a live concert in an arena with reflected sounds coming from all directions.
4
JAZZ CLUB
This mode creates the sound field of a live house with a low ceiling and hard walls. This mode gives jazz a very
vivid realism.
5
VIDEO GAME
Use this to enjoy video game sources.
6
MATRIX
Select this to emphasize the sense of expansion for music sources recorded in stereo. Signals consisting of the
difference component of the input signals (the component that provides the sense of expansion) processed for
delay are output from the surround channel.
7
VIRTUAL
Select this mode to enjoy a virtual sound field, produced from the front 2-channel speakers or headphones.
Depending on the program source being played, the effect may not be very noticeable.
In this case, try other surround modes, without worrying about their names, to create a sound field suited to your tastes.
NOTE 1: When playing sources recorded in monaural, the sound will be one-sided if signals are only input to one channel (left or right), so input
signals to both channels. If you have a source component with only one audio output (monophonic camcorder, etc.) obtain a “Y” adapter
cable to split the mono output to two outputs, and connect to the L and R inputs.
Personal Memory Plus
This set is equipped with a personal memorize function that automatically memorizes the surround modes and input modes selected for
the input different sources. When the input source is switched, the modes set for that source last time it was used are automatically
recalled.
The surround parameters, tone control settings and playback level balance for the different output channels are memorized for each
surround mode.
57
ENGLISH
DSP surround simulation
• To operate the surround mode and surround parameters from the remote control unit.
1
Select the surround mode for the input channel.
1
(Remote control unit)
The surround mode switches in the following order each time
the DSP SIMULATION button is pressed:
MONO MOVIE
MATRIX
ROCK ARENA
VIDEO GAME
JAZZ CLUB
5
4
3
2, 3
4
3
2
To enter the surround parameter setting mode, press the
SURROUND PARAMETER button.
• The surround parameter switches in the following order each time
the SURROUND PARAMETER button is pressed for the different
surround modes.
(Remote control unit)
Select the various parameters.
3
(Remote control unit)
4
(Remote control unit)
Adjust the parameter settings.
(Remote control unit)
5
Press the ENTER button to finish surround parameter mode.
(Remote control unit)
NOTE:
• When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and
the setting will be completed.
58
ENGLISH
• Operating the surround mode and surround parameters from the main unit‘s panel.
1
Turn the SELECT knob to select the surround mode.
SELECT
(Main unit)
1
2 1, 3
• When turned clockwise
DIRECT
STEREO
DOLBY PRO LOGIC IIx
VIRTUAL SURROUND
MATRIX
DTS NEO:6
VIDEO GAME
5CH/7CH STEREO
JAZZ CLUB
MONO MOVIE
ROCK ARENA
• When turned counterclockwise
DIRECT
STEREO
DOLBY PRO LOGIC IIx
VIRTUAL SURROUND
MATRIX
DTS NEO:6
VIDEO GAME
5CH/7CH STEREO
JAZZ CLUB
MONO MOVIE
ROCK ARENA
To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press the SURROUND MODE
button then operate the selector.
SURROUND
MODE
(Main unit)
2
Press the SURROUND PARAMETER button.
Press and hold in the surround parameter button to select the parameter you want to set.
• The parameters which can be set differ for the different surround modes. (Refer to “Surround Modes and Parameters” on page 60.
SURROUND
PARAMETER
(Main unit)
3
Display the parameter you want to adjust, then turn the SELECT knob to set it.
NOTE:
• When making parameter settings, the display will return to the regular condition several seconds after the last button was pressed and
the setting will be completed.
Surround parameters e
ROOM SIZE:
This sets the size of the sound field.
There are five settings: “small”, “med.s” (medium-small), “medium”, “med.l” (medium-large) and “large”. “small” recreates a small sound
field, “large” a large sound field.
EFFECT LEVEL:
This sets the strength of the surround effect.
The level can be set in 15 steps from 1 to 15. Lower the level if the sound seems distorted.
DELAY TIME:
In the matrix mode only, the delay time can be set within the range of 0 to 110 ms.
59
ENGLISH
2 Surround modes and parameters
Signals and adjustability in the different modes
Channel output
When playing
Dolby Digital
signals
When playing
DTS signals
When playing
PCM signals
When playing
ANALOG signals
B
C
C
C
C
B
C
C
C
C
B
B
E
E
E
C
B
B
B
C*
C*
C
C
B
B
B
B
C*
C
C
C
C
B
B
B
B
C*
C*
C
C
DOLBY DIGITAL
C
B
B
B
B
C
E
E
E
DTS SURROUND
C
B
B
B
B
E
C
E
E
5CH/7CH STEREO
C
B
B
B
B
C
C
C
C
ROCK ARENA
C
B
B
B
B
C
C
C
C
JAZZ CLUB
C
B
B
B
B
C
C
C
C
VIDEO GAME
C
B
B
B
B
C
C
C
C
MONO MOVIE
C
B
B
B
B
C
C
C
C
MATRIX
C
B
B
B
B
C
C
C
C
VIRTUAL
C
E
E
E
B
C
C
C
C
FRONT L/R
CENTER
SURROUND
L/R
SURROUND
BACK L/R
SUBWOOFER
DIRECT
C
E
E
E
STEREO
C
E
E
E
EXTERNAL INPUT
C
B
B
DOLBY PRO LOGIC II
C
B
DOLBY PRO LOGIC IIx
C
DTS NEO:6
Mode
C:
E:
B:
Signal / Adjustable
No signal
Turned on or off by speaker configuration setting
C : Able
E : Unable
* Only for 2 ch contents
Signals and adjustability in the different modes
When playing Dolby Digital and DTS signals
D. COMP.
LFE
SB CH OUT
(MODE)
TONE CONTROL
CINEMA EQ.
MODE
DIRECT
C (OFF)
C (0 dB)
E
E
E
E
STEREO
C (OFF)
C (0 dB)
E
C (0 dB)
E
E
E
E
E
E
E
E
DOLBY PRO LOGIC II
C (OFF)
C (0 dB)
C
C (0 dB)
C (OFF)
C
DOLBY PRO LOGIC IIx
C (OFF)
C (0 dB)
C
C (0 dB)
C (OFF)
C
DTS NEO:6
C (OFF)
C (0 dB)
C
C (0 dB)
C (OFF)
C
DOLBY DIGITAL
C (OFF)
C (0 dB)
C
C (0 dB)
C (OFF)
E
DTS SURROUND
C (OFF)
C (0 dB)
C
C (0 dB)
C (OFF)
E
5CH/7CH STEREO
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
ROCK ARENA
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
JAZZ CLUB
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
VIDEO GAME
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
MONO MOVIE
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
MATRIX
C (OFF)
C (0 dB)
C
C (0 dB)
E
E
VIRTUAL
C (OFF)
C (0 dB)
E
E
E
E
Mode
EXTERNAL INPUT
C:
E:
C:
E:
Able
Unable
Adjustable
Not adjustable
Signals and adjustability in the different modes
SURROUND PARAMETER
PRO LOGIC II / IIx ONLY
NEO:6 MUSIC
EXT. IN
ROOM SIZE
EFFECT LEVEL
DELAY TIME
SUBWOOFER
ON/OFF
PANORAMA
DIMENSION
DIRECT
E
E
E
C (OFF)
E
E
E
E
STEREO
E
E
E
E
E
E
E
E
E
EXTERNAL INPUT
E
E
E
E
E
E
E
E
C
DOLBY PRO LOGIC II
E
E
E
E
C (OFF)
C (3)
C (3)
E
E
DOLBY PRO LOGIC IIx
E
E
E
E
C (OFF)
C (3)
C (3)
E
E
DTS NEO:6
E
E
E
E
E
E
E
C (0.3)
E
DOLBY DIGITAL
E
E
E
E
E
E
E
E
E
DTS SURROUND
E
E
E
E
E
E
E
E
E
5CH/7CH STEREO
E
E
E
E
E
E
E
E
E
ROCK ARENA
C (Medium)
C (10)
E
E
E
E
E
E
E
JAZZ CLUB
C (Medium)
C (10)
E
E
E
E
E
E
E
VIDEO GAME
C (Medium)
C (10)
E
E
E
E
E
E
E
MONO MOVIE
C (Medium)
C (10)
E
E
E
E
E
E
E
MATRIX
E
E
C (30msec)
E
E
E
E
E
E
VIRTUAL
E
E
E
E
E
E
E
E
E
Mode
C:
E:
60
Adjustable
Not adjustable
CENTER WIDTH CENTER IMAGE
SW ATT
E
ENGLISH
14 LISTENING TO THE RADIO
Auto preset memory
This unit is equipped with a function for automatically searching for FM broadcast stations and storing them in the preset memory.
The “Auto tuner preset” operation can also be performed at “System setup”. (See page 33.)
1
1
When the main unit’s power operation switch turn on while
pressing the set’s PRESET • (+) button the unit automatically
begins searching for FM broadcast stations.
ON / STANDBY
ª
1
PRESET
•
2
When the first FM broadcast station is found, that station is
stored in the preset memory at channel A1. Subsequent
stations are automatically stored in order at preset channels
A1 to A8, B1 to B8, C1 to C8, D1 to D8, E1 to E8, F1 to F8
and G1 to G8 for a maximum of 56 stations.
3
Channel A1 is tuned in after the auto preset memory operation
is completed.
NOTES:
• If an FM station cannot be preset automatically due to poor
reception, use the “Manual tuning” operation to tune in the
station, then preset it using the manual “Preset memory”
operation.
• To interrupt this function, press the power operation button.
2 DEFAULT VALUE
AUTO TUNER PRESETS
A1 ~ A8
87.5/89.1/98.1/107.9/90.1/90.1/90.1/90.1 MHz
B1 ~ B8
520/600/1000/1400/1500/1710 kHz/90.1/90.1 MHz
C1 ~ C8
90.1 MHz
D1 ~ D8
90.1 MHz
E1 ~ E8
90.1 MHz
F1 ~ F8
90.1 MHz
G1 ~ G8
90.1 MHz
61
ENGLISH
Auto tuning
1
2
4
1
4
3
1
4
Set the input source to “TUNER”.
2
Press the TUNING • (+) or ª (–) button.
FUNCTION
ª
(Main unit)
2
TUNING
•
(Remote control unit)
(Main unit)
Watching the display, press the BAND button to select the
desired band (AM or FM).
(Remote control unit)
• Automatic searching begins, then stops when a station is
tuned in.
BAND
(Main unit)
3
(Remote control unit)
Press the MODE button to set the auto tuning mode.
NOTE:
• When in the auto tuning mode on the FM band, the “STEREO”
indicator lights on the display when a stereo broadcast is tuned in.
At open frequencies, the noise is muted and the “TUNED” and
“STEREO” indicators turn off.
Lit
(Remote control unit)
Manual tuning
1
2
Set the input function to “TUNER”.
Watching the display, press the BAND button to select the
desired band (AM or FM).
3
4
Press the MODE button to set the manual tuning mode.
Check that the display’s “AUTO” indicator turns off.
Press the TUNING • (+) or ª (–) button to tune in the desired
station.
The frequency changes continuously when the button is held
in.
NOTE:
• When the manual tuning mode is set, FM stereo broadcasts are received in monaural and the “STEREO” indicator turns off.
62
ENGLISH
Preset stations
Preparations:
Use the “Auto tuning” or “Manual tuning” operation to tune in the
station to be preset in the memory.
2 3
1
Press the MEMORY button.
(Remote control unit)
2
Press the SHIFT button and select the desired memory block
(A to G).
SHIFT
3
2
1, 4
(Main unit)
(Remote control unit)
NOTE: Please make sure the “AUDIO” position of the slide
switch on the remote control unit.
3
Press the PRESET • (+) or ª (–) button to select the desired
preset channel (1 to 8).
ª
PRESET
•
(Main unit)
4
(Remote control unit)
Press the MEMORY button again to
store the station in the preset memory.
(Remote control unit)
To preset other channels, repeat steps 1 to 4.
A total of 56 broadcast stations can be preset –8 stations (channels
1 to 8) in each of blocks A to G.
Checking the preset stations
• The preset (broadcast) stations can be checked on the on screen display.
1
Press the ON SCREEN/DISPLAY button repeatedly until the “Tuner Preset Stations” screen
appears on the OSD.
1
(Remote control unit)
63
ENGLISH
Recalling preset stations
1
1 2
Watching the display, press the SHIFT button to select the
preset memory block.
SHIFT
(Main unit)
(Remote control unit)
NOTE: Please make sure the “AUDIO” position of the slide
switch on the remote control unit.
2
Watching the display, press the PRESET • (+) or ª (–) button
to select the desired preset channel.
2
ª
PRESET
•
1
(Main unit)
(Remote control unit)
15 LAST FUNCTION MEMORY
• This unit is equipped with a last function memory which stores the input and output setting conditions as they were immediately before the
power is switched off.
This function eliminates the need to perform complicated resettings when the power is switched on.
• The unit is also equipped with a back-up memory. This function provides approximately one week of memory storage when the main unit’s
power switch is off and with the power cord disconnected.
16 INITIALIZATION OF THE MICROPROCESSOR
When the indication of the display is not normal or when the operation of the unit does not shows the reasonable result, the initialization of the
microprocessor is required by the following procedure.
1
2
3
Switch off the unit using the main unit’s power switch.
Hold the following SPEAKER A button and B button, and turn
the main unit’s power switch.
Check that the entire display is flashing with an interval of
about 1 second, and release your fingers from the 2 buttons
and the microprocessor will be initialized.
1, 2
NOTES:
• If step 3 does not work, start over from step 1.
• If the microprocessor has been reset, all the button settings are
reset to the default values (the values set upon shipment from
the factory).
64
2
ENGLISH
17 ADDITIONAL INFORMATION
Optimum surround sound for different sources
There are currently various types of multi-channel signals (signals or formats with more than two channels).
2 Types of multi-channel signals
Dolby Digital, Dolby Pro Logic, DTS, high definition 3-1 signals (Japan MUSE Hi-Vision audio), DVD-Audio, SACD (Super Audio CD), MPEG multichannel audio, etc.
“Source” here does not refer to the type of signal (format) but the recorded content. Sources can be divided into two major categories.
2 Types of sources
• Movie audio
Signals created to be played in movie theaters. In general sound is recorded to be played in movie theaters equipped
with multiple surround speakers, regardless of the format (Dolby Digital, DTS, etc.).
Movie theater sound field
FL
SW
C
FR
SL
Listening room sound field
SR
FL
SW
C
SL
FR
SR
SB
In this case it is important to achieve the same sense of
expansion as in a movie theater with the surround channels.
To do so, in some cases the number of surround speakers is
increased (to four or eight) or speakers with bipolar or dipolar
properties are used.
SL: Surround L channel
SR: Surround R channel
SB: Surround back channel (1 spkr or 2 spkrs)
SB
Multiple surround speakers
(For 6.1-channel system)
• Other types of audio These signals are designed to recreate a 360° sound field using three to five speakers.
FL
SW
C
FR
In this case the speakers should surround the listener from all sides to create a uniform sound
field from 360°. Ideally the surround speakers should function as “point” sound sources in the
same way as the front speakers.
SL
SR
These two types of sources thus have different properties, and different speaker settings, particularly for the surround speakers, are required
in order to achieve the ideal sound.
The AVR-2105/885 is equipped the function of surround speakers selection that makes it possible to change the settings according to the
combination of surround speakers being used and the surrounding environment in order to achieve the ideal surround sound for all sources.
This means that you can connect a pair of bipolar or dipolar surround speakers (mounted on either side of the prime listening position), as
well as a separate pair of direct radiating (monopolar) speakers placed at the rear corners of the listening room.
65
ENGLISH
Surround back speakers
A 6.1-channel system is a conventional 5.1-channel system to which the “surround back” (SB) channel has been added. This makes it easy to
achieve sound positioned directly behind the listener, something that was previously difficult with sources designed for conventional multi
surround speakers. In addition, the acoustic image extending between the sides and the rear is narrowed, thus greatly improving the expression
of the surround signals for sounds moving from the sides to the back and from the front to the point directly behind the listening position.
Change of positioning and acoustic image
with 5.1-channel systems
FL
SW
C
Change of positioning and acoustic image
with 6.1-channel systems
FR
FL
SW
C
SL ch
SL ch
SR ch
Movement of acoustic image from SR to SL
FR
SR ch
SB ch
Movement of acoustic image from SR to SB to SL
With this set, speaker(s) for 1 or 2 channels are required to achieve a 6.1-channel system (DTS-ES, etc.). Adding these speakers, however,
increases the surround effect not only with sources recorded in 6.1 channels but also with conventional 2- to 5.1-channel sources. The WIDE
SCREEN mode is a mode for achieving surround sound with up to 7.1 channels using surround back speakers, for sources recorded in
conventional Dolby Surround as well as Dolby Digital 5.1-channel and DTS Surround 5.1-channel sources. Furthermore, all the Denon original
surround modes (see page 57) are compatible with 7.1-channel playback, so you can enjoy 7.1-channel sound with any signal source.
2 Number of surround back speakers
Though the surround back channel only consists of 1 channel of playback signals for 6.1-channel sources (DTS-ES, etc.), we recommend using
two speakers. When using speakers with dipolar characteristics in particular, it is essential to use two speakers.
Using two speakers results in a smoother blend with the sound of the surround channels and better sound positioning of the surround back
channel when listening from a position other than the center.
2 Placement of the surround left and right channels when using surround back speakers
Using surround back speakers greatly improves the positioning of the sound at the rear. Because of this, the surround left and right channels
play an important role in achieving a smooth transition of the acoustic image from the front to the back. As shown on the diagram above, in a
movie theater the surround signals are also produced from diagonally in front of the listeners, creating an acoustic image as if the sound were
floating in space.
To achieve these effects, we recommend placing the speakers for the surround left and right channels slightly more towards the front than
with conventional surround systems. Doing so sometimes increases the surround effect when playing conventional 5.1-channel sources in the
6.1 surround or DTS-ES Matrix 6.1 mode. Check the surround effects of the various modes before selecting the surround mode.
66
ENGLISH
Speaker setting examples
Here we describe a number of speaker settings for different purposes. Use these examples as guides to set up your system according to the type
of speakers used and the main usage purpose.
1. DTS-ES compatible system (using surround back speakers)
(1) Basic setting for primarily watching movies
This is recommended when mainly playing movies and using regular single way or 2-way speakers for the surround speakers.
Front speakers
Center speaker
Monitor
Subwoofer
60°
Surround
speakers
60°
Surround back speakers
• Set the front speakers with their front surfaces as flush with the TV
Surround speaker Surround back
or monitor screen as possible. Set the center speaker between the
speaker
front left and right speakers and no further from the listening position
Point slightly
than the front speakers.
Front speaker
downwards
• Consult the owner’s manual for your subwoofer for advice on placing
the subwoofer within the listening room.
2 to 3 feet
• If the surround speakers are direct-radiating (monopolar) then place
them slightly behind and at an angle to the listening position and
parallel to the walls at a position 2 to 3 feet (60 to 90 cm) above ear
As seen from the side
level at the prime listening position.
• When using two surround back speakers, place them at the back
facing the front at a narrower distance than the front left and right speakers. When using one surround back speaker,
place it at the rear center facing the front at a slightly higher position 0 to 0.7 feet (0 to 20 cm) than the surround
speakers.
• We recommend installing the surround back speaker(s) at a slightly downward facing angle. This effectively prevents
the surround back channel signals from reflecting off the monitor or screen at the front center, resulting in interference
and making the sense of movement from the front to the back less sharp.
As seen from above
(2) Setting for primarily watching movies using diffusion type speakers for the surround speakers
For the greatest sense of surround sound envelopment, diffuse radiation speakers such as bipolar types, or dipolar types, provide a wider
dispersion than is possible to obtain from a direct radiating speaker (monopolar). Place these speakers at either side of the prime listening
position, mounted above ear level.
Path of the surround sound from the
speakers to the listening position
Surround
speakers
• Set the front speakers, center speaker and subwoofer in the same
positions as in example (1).
• It is best to place the surround speakers directly at the side or slightly
to the front of the viewing position, and 2 to 3 feet (60 to 90 cm)
above the ears.
• Same as surround back speaker installation method (1).
Using dipolar speakers for the surround back speakers as well is
more effective.
• The signals from the surround channels reflect off the walls as
shown on the diagram at the left, creating an enveloping and realistic
surround sound presentation.
Surround speaker
Surround back
speaker
Point slightly
downwards
Front speaker
2 to 3 feet
As seen from the side
60°
Surround back speakers
As seen from above
2. When not using surround back speakers
Front speakers
Center speaker
Monitor
Subwoofer
60°
• Set the front speakers with their front surfaces as flush with the TV or
monitor screen as possible. Set the center speaker between the front left
and right speakers and no further from the listening position than the front
speakers.
• Consult the owner’s manual for your subwoofer for advice on placing the
subwoofer within the listening room.
• If the surround speakers are direct-radiating (monopolar) then place them
slightly behind and at an angle to the listening position and parallel to the
walls at a position 2 to 3 feet (60 to 90 cm) above ear level at the prime
listening position.
Surround speaker
Front speaker
2 to 3 feet
As seen from the side
120°
Surround speakers
As seen from above
67
ENGLISH
Surround
The AVR-2105/885 is equipped with a digital signal processing circuit that lets you play program sources in the surround mode to achieve the same
sense of presence as in a movie theater.
Dolby Surround
(1) Dolby Digital
Dolby Digital is the multi-channel digital signal format developed by Dolby Laboratories.
Dolby Digital consists of up to “5.1” channels - front left, front right, center, surround left, surround right, and an additional channel exclusively
reserved for additional deep bass sound effects (the Low Frequency Effects – LFE – channel, also called the “.1” channel, containing bass
frequencies of up to 120 Hz).
Unlike the analog Dolby Pro Logic format, Dolby Digital’s main channels can all contain full range sound information, from the lowest bass, up
to the highest frequencies – 22 kHz. The signals within each channel are distinct from the others, allowing pinpoint sound imaging, and Dolby
Digital offers tremendous dynamic range from the most powerful sound effects to the quietest, softest sounds, free from noise and distortion.
2 Dolby Digital and Dolby Pro Logic
Comparison of home surround systems
Dolby Digital
Dolby Pro Logic
No. recorded channels (elements)
5.1 ch
2 ch
No. playback channels
5.1 ch
4 ch
L, R, C, SL, SR, SW
L, R, C, S (SW - recommended)
Playback channels (max.)
Digital discrete processing
Dolby Digital encoding/decoding
Audio processing
High frequency playback limit of surround
channel
Analog matrix processing Dolby Surround
20 kHz
7 kHz
2 Dolby Digital compatible media and playback methods
Marks indicating Dolby Digital compatibility:
.
The following are general examples. Also refer to the player’s operating instructions.
Media
LD (VDP)
Dolby Digital output jacks
Coaxial Dolby Digital RF output jack
Playback method (reference page)
1
Set the input mode to “AUTO”.
(Page 40)
DVD
Optical or coaxial digital output
(same as for PCM)
2
Set the input mode to “AUTO”.
(Page 40)
Others
(satellite broadcasts, CATV, etc.)
Optical or coaxial digital output
(same as for PCM)
Set the input mode to “AUTO”.
(Page 40)
1 Please use a commercially available adapter when connecting the Dolby Digital RF output jack of the LD player to the digital input jack.
Please refer to the instruction manual of the adapter when making connection.
2 Some DVD digital outputs have the function of switching the Dolby Digital signal output method between “bit stream” and “(convert to)
PCM”. When playing in Dolby Digital surround on the AVR-2105/885, switch the DVD player’s output mode to “bit stream”. In some cases
players are equipped with both “bit stream + PCM” and “PCM only” digital outputs. In this case connect the “bit stream + PCM” jacks
to the AVR-2105/885.
(2) Dolby Pro Logic IIx
• Dolby Pro Logic IIx furthers the matrix decoding technology of Dolby Pro Logic II to decode audio signals recorded on two channels into
up to 7.1 playback channels, including the surround back channel. Dolby Pro Logic IIx also allows 5.1-channel sources to be played in up to
7.1 channels.
The mode can be selected according to the source. The Music mode is best suited for playing music, the Cinema mode for playing movies,
and the Game mode for playing games. The Game mode can only be used with 2-channel audio sources.
(3) Dolby Pro Logic II
• Dolby Pro Logic II is a new multi-channel playback format developed by Dolby Laboratories using feedback logic steering technology and
offering improvements over conventional Dolby Pro Logic circuits.
• Dolby Pro Logic II can be used to decode not only sources recorded in Dolby Surround ( ) but also regular stereo sources into five channels
(front left, front right, center, surround left and surround right) to achieve surround sound.
• Whereas with conventional Dolby Pro Logic the surround channel playback frequency band was limited, Dolby Pro Logic II offers a wider
band range (20 Hz to 20 kHz or greater). In addition, the surround channels were monaural (the surround left and right channels were the
same) with previous Dolby Pro Logic, but Dolby Pro Logic II they are played as stereo signals.
• Various parameters can be set according to the type of source and the contents, so it is possible to achieve optimum decoding (see page
60).
68
ENGLISH
Sources recorded in Dolby Surround
These are sources in which three or more channels of surround have been recorded as two channels of signals using Dolby Surround
encoding technology.
Dolby Surround is used for the sound tracks of movies recorded on DVDs, LDs and Video cassettes to be played on stereo VCRs, as well
as for the stereo broadcast signals of FM radio, TV, satellite broadcasts and cable TV.
Decoding these signals with Dolby Pro Logic II makes it possible to achieve multi-channel surround playback. The signals can also be
played on ordinary stereo equipment, in which case they provide normal stereo sound.
There are two types of DVD Dolby surround recording signals.
q 2-channel PCM stereo signals
w 2-channel Dolby Digital signals
When either of these signals is input to the AVR-2105/885, the surround mode is automatically set to Dolby Pro Logic II when the
“DOLBY/DTS SURROUND” mode is selected.
2 Sources recorded in Dolby Surround are indicated with the logo mark shown below.
Dolby Surround support mark:
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
DTS Digital Surround
Digital Theater Surround (also called simply DTS) is a multi-channel digital signal format developed by Digital Theater Systems.
DTS offers the same “5.1” playback channels as Dolby Digital (front left, front right and center, surround left and surround right) as well as the
stereo 2-channel mode. The signals for the different channels are fully independent, eliminating the risk of deterioration of sound quality due to
interference between signals, crosstalk, etc.
DTS features a relatively higher bit rate as compared to Dolby Digital (1234 kbps for CDs and LDs, 1536 kbps for DVDs) so it operates with a
relatively low compression rate. Because of this the amount of data is great, and when DTS playback is used in movie theaters, a separate CDROM synchronized with the film is played.
With LDs and DVDs, there is of course no need for an extra disc; the pictures and sound can be recorded simultaneously on the same disc, so
the discs can be handled in the same way as discs with other formats.
There are also music CDs recorded in DTS. These CDs include 5.1-channel surround signals (compared to two channels on current CDs). They do
not include picture data, but they offer surround playback on CD players that are equipped with digital outputs (PCM type digital output required).
DTS surround track playback offers the same intricate, grand sound as in a movie theater, right in your own listening room.
2 DTS compatible media and playback methods
Marks indicating DTS compatibility:
and
.
The following are general examples. Also refer to the player’s operating instructions.
Media
Dolby Digital output jacks
Playback method (reference page)
CD
Optical or coaxial digital output
(same as for PCM)
2
Set the input mode to “AUTO” or “DTS” (page 40).
Never set the mode to “ANALOG” or “PCM”.
1
LD (VDP)
Optical or coaxial digital output
(same as for PCM)
2
Set the input mode to “AUTO” or “DTS” (page 40).
Never set the mode to “ANALOG” or “PCM”.
1
DVD
Optical or coaxial digital output
(same as for PCM)
3
Set the input mode to “AUTO” or “DTS” (page 40).
1 DTS signals are recorded in the same way on CDs and LDs as PCM signals. Because of this, the un-decoded DTS signals are output as
random “hissy” noise from the CD or LD player’s analog outputs. If this noise is played with the amplifier set at a very high volume, it may
possibly cause damage to the speakers. To avoid this, be sure to switch the input mode to “AUTO” or “DTS” before playing CDs or LDs
recorded in DTS. Also, never switch the input mode to “ANALOG” or “PCM” during playback. The same holds true when playing CDs or
LDs on a DVD player or LD/DVD compatible player. For DVDs, the DTS signals are recorded in a special way so this problem does not occur.
2 The signals provided at the digital outputs of a CD or LD player may undergo some sort of internal signal processing (output level
adjustment, sampling frequency conversion, etc.). In this case the DTS-encoded signals may be processed erroneously, in which case they
cannot be decoded by the AVR-2105/885, or may only produce noise. Before playing DTS signals for the first time, turn down the master
volume to a low level, start playing the DTS disc, then check whether the DTS indicator on the AVR-2105/885 (see page 41) lights before
turning up the master volume.
3 A DVD player with DTS-compatible digital output is required to play DTS DVDs. A DTS Digital Output logo is featured on the front panel of
compatible DVD players. Recent DENON DVD player models feature DTS-compatible digital output – consult the player’s owner’s manual
for information on configuring the digital output for DTS playback of DTS-encoded DVDs.
69
ENGLISH
MANUFACTURED UNDER LICENSE FROM DIGITAL THEATER SYSTEMS, INC.
U.S. PAT. NO’S. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 AND OTHER U.S. AND WORLD–WIDE PATENTS
ISSUED AND PENDING.
“DTS”, “DTS–ES”, “Neo:6”, AND “DTS 96/24” ARE TRADEMARKS OF DIGITAL THEATER SYSTEMS, INC. © 1996, 2003 DIGITAL
THEATER SYSTEMS, INC. ALL RIGHTS RESERVED.
DTS-ES Extended Surround™
DTS-ES Extended Surround is a new multi-channel digital signal format developed by Digital Theater Systems Inc. While offering high compatibility
with the conventional DTS Digital Surround format, DTS-ES Extended Surround greatly improves the 360-degree surround impression and space
expression thanks to further expanded surround signals. This format has been used professionally in movie theaters since 1999.
In addition to the 5.1 surround channels (FL, FR, C, SL, SR and LFE), DTS-ES Extended Surround also offers the SB (Surround Back, sometimes
also referred to as “surround center”) channel for surround playback with a total of 6.1 channels. DTS-ES Extended Surround includes two signal
formats with different surround signal recording methods, as described below.
2
DTS-ES™ Discrete 6.1
DTS-ES Discrete 6.1 is the newest recording format. With it, all 6.1 channels (including the SB channel) are recorded independently using a
digital discrete system. The main feature of this format is that because the SL, SR and SB channels are fully independent, the sound can be
designed with total freedom and it is possible to achieve a sense that the acoustic images are moving about freely among the background
sounds surrounding the listener from 360 degrees.
Though maximum performance is achieved when sound tracks recorded with this system are played using a DTS-ES decoder, when played
with a conventional DTS decoder the SB channel signals are automatically down-mixed to the SL and SR channels, so none of the signal
components are lost.
2
DTS-ES™ Matrix 6.1
With this format, the additional SB channel signals undergo matrix encoding and are input to the SL and SR channels beforehand. Upon
playback they are decoded to the SL, SR and SB channels. The performance of the encoder used at the time of recording can be fully matched
using a high precision digital matrix decoder developed by DTS, thereby achieving surround sound more faithful to the producer’s sound design
aims than with conventional 5.1- or 6.1-channel systems.
In addition, the bit stream format is 100% compatible with conventional DTS signals, so the effect of the Matrix 6.1 format can be achieved
even with 5.1-channel signal sources. Of course it is also possible to play DTS-ES Matrix 6.1 encoded sources with a DTS 5.1-channel decoder.
When DTS-ES Discrete 6.1 or Matrix 6.1 encoded sources are decoded with a DTS-ES decoder, the format is automatically detected upon
decoding and the optimum playing mode is selected. However, some Matrix 6.1 sources may be detected as having a 5.1-channel format, so the
DTS-ES Matrix 6.1 mode must be set manually to play these sources.
(For instructions on selecting the surround mode, see page 54.)
The DTS-ES decoder includes another function, the DTS Neo:6 surround mode for 6.1-channel playback of digital PCM and analog signal sources.
2
70
DTS Neo:6™ surround
This mode applies conventional 2-channel signals to the high precision digital matrix decoder used for DTS-ES Matrix 6.1 to achieve 6.1channel surround playback. High precision input signal detection and matrix processing enable full band reproduction (frequency response of
20 Hz to 20 kHz or greater) for all 6.1 channels, and separation between the different channels is improved to the same level as that of a digital
discrete system.
DTS Neo:6 surround includes two modes for selecting the optimum decoding for the signal source.
• DTS Neo:6 Cinema
This mode is optimum for playing movies. Decoding is performed with emphasis on separation performance to achieve the same
atmosphere with 2-channel sources as with 6.1-channel sources.
This mode is effective for playing sources recorded in conventional surround formats as well, because the in-phase component is assigned
mainly to the center channel (C) and the reversed phase component to the surround (SL, SR and SB channels).
• DTS Neo:6 Music
This mode is suited mainly for playing music. Changes in the sound quality are reduced by decoding with emphasis on the front channel
signals (FL and FR), and a natural sense of expansion is given to the sound field by the effect of the surround signals output from the center
(C) and surround (SL, SR and SB) channels.
ENGLISH
DTS 96/24
The sampling frequency, number of bits and number of channels used for recording of music, etc., in studios has been increasing in recent years,
and there are a growing number of high quality signal sources, including 96 kHz/24 bit 5.1-channel sources.
For example, there are high picture/sound quality DVD video sources with 96 kHz/24 bit stereo PCM audio tracks.
However, because the data rate for these audio tracks is extremely high, there are limits to recording them on two channels only, and since the
quality of the pictures must be restricted it is common to only include still pictures.
In addition, 96 kHz/24 bit 5.1-channel surround is possible with DVD audio sources, but DVD audio players are required to play them with this high
quality.
DTS 96/24 is a multi-channel digital signal format developed by Digital Theater Systems Inc. in order to deal with this situation.
Conventional surround formats used sampling frequencies of 48 or 44.1 kHz, so 20 kHz was about the maximum playback signal frequency. With
DTS 96/24, the sampling frequency is increased to 96 or 88.2 kHz to achieve a wide frequency range of over 40 kHz.
In addition, DTS 96/24 has a resolution of 24 bits, resulting in the same frequency band and dynamic range as 96 kHz/24 bit PCM.
As with conventional DTS Surround, DTS 96/24 is compatible with a maximum of 5.1 channels, so sources recorded using DTS 96/24 can be
played in high sampling frequency, multiple channel audio with such normal media as DVD videos and CDs.
Thus, with DTS 96/24, the same 96 kHz/24 bit multi-channel surround sound as with DVD-Audio can be achieved while viewing DVD-Video images
on a conventional DVD-Video player ( 1). Furthermore, with DTS 96/24 compatible CDs, 88.2 kHz/24 bit multi-channel surround can be achieved
using normal CD/LD players ( 1).
Even with the high quality multi-channel signals, the recording time is the same as with conventional DTS surround sources.
What’s more, DTS 96/24 is fully compatible with the conventional DTS surround format, so DTS 96/24 signal sources can be played with a
sampling frequency of 48 kHz or 44.1 kHz on conventional DTS or DTS-ES surround decoders ( 2).
1: A DVD player with DTS digital output capabilities (for CD/LD players, a player with digital outputs for conventional DTS CDs/LDs) and a
disc recorded in DTS 96/24 are required.
2: The resolution is 24 or 20 bits, depending on the decoder.
71
ENGLISH
18 TROUBLESHOOTING
If a problem should arise,first check the following.
1. Are the connections correct ?
2. Have you operated the receiver according to the Operating Instructions ?
3. Are the speakers, turntable and other components operating property ?
If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction.
Disconnect the power immediately and contact your store of purchase.
When playing records
Common problems when listening to the CD, records, tapes and FM broadcasts, etc.
Symptom
DISPLAY not lit and sound not produced
when power switch set to on.
DISPLAY lit but sound not produced.
Page
• Power cord not plugged in securely.
• Check the insertion of the power cord plug.
• Turn the power on with the remote control
unit after turning the POWER switch on.
7
39
• Speaker cords not securely connected.
• Improper position of the audio function
button.
• Volume control set to minimum.
• MUTING is on.
• Digital signals not input Digital input
selected.
• Connect securely.
• Set to a suitable position.
• Turn volume up to suitable level.
• Switch off MUTING.
• Input digital signals or select input jacks to
which digital signals are being input.
41
43
41
• Speaker terminals are short-circuited.
• Switch power off, connect speakers
properly, then switch power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
• Turn off the set’s power, then ventilate it
well to cool it down.
Once the set is cooled down, turn the
power back on.
14, 15
14, 15
7 ~ 15
DISPLAY not lit and power indicator is
flashing rapidly.
• The unit is operating at continuous high
power conditions and/or inadequate
ventilation.
14, 15
40
5, 14
5, 14
Sound produced only from one channel.
• Incomplete connection of speaker cords.
• Incomplete connection of input/output
cords.
• Connect securely.
• Connect securely.
Positions of instruments reversed during
stereo playback.
• Reverse connections of left and right
speakers or left and right input/output
cords.
• Check left and right connections.
15
• Ground wire of turntable not connected
properly.
• Incomplete PHONO jack connection.
• TV or radio transmission antenna nearby.
• Connect securely.
7
Humming noise produced when record is
playing.
• Connect securely.
• Contact your store of purchase.
7
—
• Turntable and speaker systems too close
together.
• Floor is unstable and vibrates easily.
• Separate as much as possible.
—
• Use cushions to absorb speaker vibrations
transmitted by floor. If turntable is not
equipped with insulators, use audio
insulators (commonly available).
—
• Stylus pressure too weak.
• Dust or dirt on stylus.
• Cartridge defective.
• Apply proper stylus pressure.
• Check stylus.
• Replace cartridge.
—
—
—
• MC cartridge being used.
• Replace with MM cartridge or use a head
amplifier or step-up transformer.
7
• Batteries dead.
• Remote control unit too far from this unit.
• Obstacle between this unit and remote
control unit.
• Different button is being pressed.
• < and > ends of battery inserted in reverse.
• Replace with new batteries.
• Move closer.
• Remove obstacle.
18
18
18
• Press the proper button.
• Insert batteries properly.
—
18
Howling noise produced when volume is
high.
Volume is weak.
Remote control
unit
Measures
• Block the ventilation holes of the set.
Sound is distorted.
72
Cause
This unit does not operate properly when
remote control unit is used.
ENGLISH
19 SPECIFICATIONS
2
Audio section
• Power amplifier
Rated output:
Front:
Dynamic power:
Output terminals:
90 W + 90 W
125 W + 125 W
Center:
90 W
125 W
Surround:
90 W + 90 W
125 W + 125 W
Surround Back: 90 W + 90 W
125 W + 125 W
120 W x 2 ch (8 Ω/ohms)
170 W x 2 ch (4 Ω/ohms)
200 W x 2 ch (2 Ω/ohms)
Front:
A or B
16
A + B
12
Center, Surround, Surr.Back:
16
(8
(6
(8
(6
(8
(6
(8
(6
Ω/ohms,
Ω/ohms,
Ω/ohms,
Ω/ohms,
Ω/ohms,
Ω/ohms,
Ω/ohms,
Ω/ohms,
20 Hz ~ 20 kHz with 0.08%
1 kHz with 0.7% T.H.D.)
20 Hz ~ 20 kHz with 0.08%
1 kHz with 0.7% T.H.D.)
20 Hz ~ 20 kHz with 0.08%
1 kHz with 0.7% T.H.D.)
20 Hz ~ 20 kHz with 0.08%
1 kHz with 0.7% T.H.D.)
T.H.D.)
T.H.D.)
T.H.D.)
T.H.D.)
~ 16 Ω/ohms
~ 16 Ω/ohms
~ 16 Ω/ohms
• Analog
Input sensitivity / input impedance:
200 mV / 47 kΩ/kohms
Frequency response:
10 Hz ~ 100 kHz: +1, –3 dB (DIRECT mode)
S/N:
100 dB (IHF-A weighted) (DIRECT mode)
Distortion:
0.008% (20 Hz ~ 20 kHz) (DIRECT mode)
Rated output:
1.2 V
• Phono equalizer (PHONO input — REC OUT)
Input sensitivity:
2.5 mV
RIAA deviation:
±1 dB (20 Hz to 20 kHz)
Signal-to-noise ratio:
74 dB (A weighting, with 5 mV input)
Rated output / Maximum output:
150 mV / 7 V
Distortion factor:
0.03% (1 kHz, 3 V)
2
Video section
• Standard video jacks
Input / output level and impedance:
Frequency response:
• S-video jacks
Input / output level and impedance:
Frequency response:
• Color component video jacks
Input / output level and impedance:
Frequency response:
2
S/N (IHF-A):
Total Harmonic Distortion (at 1 kHz):
General
Power supply:
Power consumption:
Maximum external dimensions:
Weight:
2
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
C (color) signal — 0.286 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Y (brightness) signal — 1 Vp-p, 75 Ω/ohms
PB/CB (blue) signal — 0.7 Vp-p, 75 Ω/ohms
PR/CR (red) signal — 0.7Vp-p, 75 Ω/ohms
DC ~ 100 MHz — +0, –3 dB
Tuner section
Receiving Range:
Usable Sensitivity:
50 dB Quieting Sensitivity:
2
1 Vp-p, 75 Ω/ohms
5 Hz ~ 10 MHz — +1, –3 dB
Remote control unit (RC-980)
Batteries:
External dimensions:
Weight:
[FM] (note: µV at 75 Ω/ohms, 0 dBf=1 x 10–15 W)
87.50 MHz ~ 107.90 MHz
1.0 µV (11.2 dBf)
MONO
1.6 µV (15.3 dBf)
STEREO 23 µV (38.5 dBf)
MONO
77 dB (IHF-A weighted)
STEREO 72 dB (IHF-A weighted)
MONO
0.15% (1kHz)
STEREO 0.3% (1kHz)
[AM]
520 kHz ~ 1710 kHz
18 µV
AC 120 V, 60 Hz
5.3 A
1 W Max. (Standby)
434 (W) x 171 (H) x 417 (D) mm (17-3/32” x 6-47/64” x 16-27/64”)
13.3 kg (29 lbs 5 oz)
R6P/AA Type (three batteries)
55 (W) x 225 (H) x 34.5 (D) mm (2-11/64” x 8-55/64” x 1-9/64”)
165 g (Approx. 5.8 oz) (including batteries)
* For purposes of improvement, specifications and design are subject to change without notice.
73
ENGLISH
FRANCAIS
LIST OF PRESET CODES / LISTE DE CODES PRÉRÉGLÉS
DVD
Denon
014, *[111]
Cybernex
087
Aiwa
009
Daewoo
025, 055, 059, 074, 089, 093, 095,
Hitachi
010
JVC
006, 011
Daytron
025, 055
Konka
012, 013
DBX
005, 085
Magnavox
005
Dumont
053
Mitsubishi
004
Dynatech
009
Panasonic
014
Electrohome
001, 088, 097
Philips
005, 015, 016, 017
Electrophonic
088
Pioneer
003, 008
Emerson
Sanyo
018
Sony
002, 019, 020
Toshiba
001, 021, 022
Zenith
023
096
001, 009, 017, 027, 086, 088, 089,
092, 093, 097, 100, 101, 102, 103,
104, 117
Fisher
009, 028, 031, 053, 054, 091, 099,
115
GE
007, 011, 049, 050, 051, 052, 073,
028, 029, 112
Go Video
047, 048
Magnavox
026
Goldstar
000, 006, 012, 062, 088
Mitsubishi
028
Gradiente
094
Panasonic
029, 030
Grundig
042
Philips
026
Harley Davidson
094
Pioneer
028, 031
Harman Kardon
040, 062
RCA
032
Hi-Q
091
Sony
033, 034, 035, 036
Hitachi
009, 013, 023, 026, 058, *[108],
VDP
Denon
080, 087
109, 110, 111
VCR
JC Penny
004, 005, 007, 023, 028, 049, 062,
Admiral
081
Aiko
095
Jensen
013, 026
Aiwa
009
JVC
004, 005, 006, 026, 029, 043, 044,
Akai
026, 027, 070, 072, 082, 083, 084
Alba
055
Amstrad
009
ASA
085, 087, 088
045, 046, 085
Kenwood
004, 005, 006, 026, 029, 033, 045,
042
Kodak
088
Asha
087
Lloyd
009, 094
Audio Dynamic
005, 085
LXI
088
Audiovox
088
Magnavox
015, 016, 042, 049, 063, 106
Beaumark
087
Magnin
087
Broksonic
086, 093
Marantz
Calix
088
Candle
006, 087, 088, 089, 090
Marta
088
Canon
049, 057
MEI
049
Capehart
025, 055, 056, 071
Memorex
Carver
015
CCE
095
Metz
Citizen
006, 007, 087, 088, 089, 090, 095
MGA
001, 017, 027, 041, 097
Craig
007, 087, 088, 091, 115
MGN Technology
087
Curtis Mathes
006, 049, 073, 080, 087, 090, 092
Midland
011
144
085, 090
004, 005, 006, 015, 042, 049, 085,
090
009, 033, 049, 053, 060, 081, 087,
088, 091, 094, 115
123, 124, 125, 126, 127, 128
FRANCAIS
Minolta
013, 023
Shogun
087
Mitsubishi
001, 003, 008, 013, 014, 017, 027,
Sony
075, 076, 077, 078, 079, 121, 122
029, 039, 040, 041, 045, 097
STS
023
081
Sylvania
009, 015, 016, 017, 041, 049, 094
Symphonic
009, 094
115, 117
Tandy
009
009, 087, 094
Tashiko
009, 088
Multitech
007, 009, 011, 087, 090, 094
Tatung
004, 026, 030
NAD
038
Teac
004, 009, 026, 094
NEC
004, 005, 006, 018, 026, 029, 045,
Technics
024, 049
061, 062, 085
Teknika
009, 010, 022, 049, 088, 094
Nikko
088
TMK
087, 092
Noblex
087
Toshiba
013, 017, 020, 041, 059, 089, 098,
Optimus
081, 088
Optonica
021
Totevision
007, 087, 088
Motorola
Montgomery Ward 001, 002, 007, 009, 049, 063, 081,
MTC
099, 117
024, 049, 064, 066, 067, 068, 069,
Unirech
087
107
Vecrtor Research
005, 062, 085, 089, 090
009
Victor
005, 045, 046, 085
Pentax
009, 013, 023, 058, 090
Video Concepts
005, 027, 085, 089, 090
Philco
015, 016, 049
Videosonic
007, 087
Philips
015, 021, 042, 049, 105
Wards
Pilot
088
Panasonic
Perdio
013, 021, 023, 087, 088, 089, 091,
094, 097, 118, 119, 120
005, 013, 029, 036, 037, 038, 045,
XR-1000
094
085
Yamaha
004, 005, 006, 026, 062, 085
Portland
025, 055, 090
Zenith
060, 078, 079
Proscan
063, 080
Pulsar
060
TV
Quartz
033
Admiral
045, 121
Quasar
034, 035, 049
Adventura
122
Radio Shack
001, 002, 021, 081, 087, 088, 091,
Aiko
054
094, 097, 098, 115
Akai
016, 027, 046
Radix
088
Alleron
062
Randex
088
A-Mark
007
RCA
007, 013, 019, 023, 058, 063, 064,
Amtron
061
065, 073, 080, 082, 087
Anam
006, 007, 036
009, 021, 031, 033, 049, 053, 081,
Anam National
061, 147
087, 088, 091, 094, 097, 098
AOC
003, 007, 033, 038, 039, 047, 048,
Pioneer
Realistic
ENGLISH
Ricoh
055
Salora
033, 041
Archer
007
Samsung
007, 011, 051, 059, 070, 083, 087,
Audiovox
007, 061
089, 113
Bauer
155
Sanky
081
Belcor
047
Sansui
005, 026, 029, 045, 061, 085, 114
Bell & Howell
045, 118
Sanyo
032, 033, 053, 087, 091, 115, 116
Bradford
061
SBR
042
Brockwood
003, 047
Scott
017, 020, 086, 089, 093, 117
Candle
003, 030, 031, 032, 038, 047, 049,
Sears
013, 023, 028, 031, 033, 053, 054,
049, 133
050, 122
088, 091, 098, 099, 115
Capehart
003
Sentra
055
Celebrity
046
Sharp
001, 002, 021, 097
145
ENGLISH
FRANCAIS
Circuit City
003
KTV
074, 123
Citizen
029, 030, 031, 032, 034, 038, 047,
Loewe
071
049, 050, 054, 061, 095, 122, 123
Logik
144
Concerto
031, 047, 049
Luxman
031
Colortyme
003, 047, 049, 135
LXI
008, 014, 017, 024, 040, 044, 063,
Contec
013, 051, 052, 061
Cony
051, 052, 061
071, 075, 076, 077, 118, 125
Magnavox
005, 010, 017, 030, 033, 038, 050,
Craig
004, 061
056, 071, 078, 079, 085, 089, 108,
Crown
029
109, 110, 127, 131, 132, 145
Curtis Mathes
Daewoo
029, 034, 038, 044, 047, 049, 053,
Marantz
015, 017, 071, 080
095, 118
Matsui
027
027, 029, 039, 048, 049, 054, 055,
Memorex
014, 027, 045, 083, 118, 144
106, 107, 137
Metz
160, 161, 162, 163
Daytron
003, 049
MGA
Dimensia
044
Dixi
007, 015, 027
Midland
125
Electroband
046
Minutz
066
Electrohome
029, 056, 057, 058, 147
Mitsubishi
001, 016, 039, 048, 056, 057, 058,
Elta
027
Emerson
029, 051, 059, 060, 061, 062, 118,
Montgomery Ward 011, 020, 144, 145, 146
001, 039, 048, 056, 057, 058, 065,
081, 083
065, 081, 082, 083, 105
123, 124, 139, 148
Motorola
121, 147
Envision
038
MTC
031, 034, 039, 048, 095
Etron
027
NAD
008, 075, 076, 128
Fisher
014, 021, 063, 064, 065, 118
National
002, 036, 061, 147
Formenti
155
National Quenties
002
Fortress
012
NEC
031, 038, 039, 048, 057, 084, 086,
Fujitsu
004, 062
Funai
004, 062
Nikko
054
Futuretech
004
NTC
054
GE
Goldstar
135, 147
020, 036, 037, 040, 044, 058, 066,
Optimus
128
088, 119, 120, 125, 147
Optonica
011, 012, 093, 121
000, 015, 029, 031, 039, 048, 051,
Orion
004, 139
056, 057, 067, 068, 069, 116
Panasonic
002, 009, 017, 036, 037, 071, 141,
Philco
005, 010, 030, 050, 051, 056, 079,
Philips
005, 015, 017, 050, 051, 056, 078,
Grundy
062
Hitachi
029, 031, 051, 052, 070, 111, 112,
Hitachi Pay TV
151
Infinity
017, 071
Janeil
122
Pioneer
124, 128, 142
JBL
017, 071
Portland
054
JC Penny
020, 034, 039, 040, 041, 044, 048,
Price Club
095
050, 058, 066, 069, 076, 088, 090,
Proscan
040, 044, 125
143, 147
113, 124, *[134]
085, 127, 131, 132, 145, 147
087, 088, 089, 131, 132, 147
095, 125, 136, 159
Proton
035, 051, 092, 129
JCB
046
Pulsar
042
JVC
019, 051, 052, 072, 073, 091, 117,
Quasar
036, 037, 074, 141
126
Radio Shack
011, 044, 063, 093, 118
Kawasho
018, 046
RCA
040, 044, 125, 130, 137, 151, 152
Kenwood
038, 056, 057
Realistic
014, 063, 093, 118
Kloss
010, 032
Saisho
027
Kloss Novabeam
005, 122, 127, 131
146
FRANCAIS
Samsung
003, 015, 034, 053, 055, 057, 094,
Eastern
015
095, 136, 153
Garrard
011
Sansui
139
Gemini
030, 033, 034
Sanyo
013, 014, 021, 022, 063, 064, 081,
General Instrument 030, 031, 032
096
Hytex
006
SBR
015
Jasco
011
Schneider
015
Jerrold
009, 016, 017, 026, 032
Scott
062
Magnavox
018
Sears
008, 014, 021, 022, 023, 024, 025,
Movie Time
019
040, 052, 057, 062, 063, 064, 065,
NSC
019
073, 075, 076, 097, 098, 125, 159
Oak
000, 006, 020
011, 012, 013, 026, 093, 099, 100,
Panasonic
001, 005
104, 121
Philips
011, 012, 013, 018, 021
Siemens
013
Pioneer
002, 003, 022
Signature
045, 144
RCA
029
Simpson
050
Regency
015
Sony
043, 046, 138, 146, 150
Samsung
014, 023
Soundesign
030, 050, 062
Scientific Atlanta
004, 024, 025
Spectricon
007, 033
Signal
014
Squareview
004
SL Marx
014
Supre-Macy
032, 122
Starcom
009
Supreme
046
Stargate
014
Sylvania
005, 010, 017, 030, 078, 079, 085,
Teleview
014
089, 101, 127, 131, 132, 145, 155
Tocom
007, 016
Symphonic
004, 148
TV86
019
Tandy
012, 121
Unika
011
Tatung
036, 124
United Artists
006
Technics
037
Universal
010, 011
Teknika
001, 030, 032, 034, 052, 054, 078,
Viewstar
018, 019
083, 095, 144, 156, 157
Zenith
027, 028
Tera
035, 129
Toshiba
008, 014, 034, 063, 075, 076, 095,
DBS (SATELLITE)
097, 136, 158, 159
Alphastar
054
Universal
020, 066, 088
Chaparral
035, 036
Victor
019, 073, 126
Dishnet
053
Video Concepts
016
Drake
037, 038
Viking
032, 122
Echostar Dish
062, 066
Wards
005, 045, 066, 078, 085, 088, 089,
GE
048, 055, 056
Sharp
093, 102, 103, 131, 132, 148
General Instruments 039, 040, 041
Zenith
042, 114, 115, 140, 144, 149
Grundig
070, 071, 072, 073
Zonda
007
Hitachi
058, 059
CABLE
Hughes Network
063, 064, 065, 069
JVC
057
ABC
006, *[007], 008, 009
Kathrein
074, 075, 076, 083
Archer
010, 011
Magnavox
060
Century
011
Nokia
070, 080, 084, 085, 086
Citizen
011
Philips
060
Colour Voice
012, 013
Primestar
051
Comtronic
014
Proscan
048, 055, 056
ENGLISH
147
ENGLISH
FRANCAIS
RCA
048, 055, 056, 068
TAPE
Realistic
042
Denon
*[111]
Sierra I
036
Aiwa
001, 002
Sierra II
036
Carver
002
Sierra III
036
Harman/Kardon
002, 003
Sony
049, 067
JVC
004, 005
STS1
043
Kenwood
006
STS2
044
Magnavox
002
STS3
045
Marantz
002
SRS4
046
Onkyo
016, 018
Technisat
077, 078, 079, 081, 082
Optimus
007, 008
Toshiba
047, 050
Panasonic
012
Uniden
061
Philips
002
Pioneer
007, 008, 009
CD
Sony
013, 014, 015
Denon
*[111]
Technics
012
Aiwa
001, 035, 043
Victor
004
Burmster
002
Wards
007
Carver
003, 035
Yamaha
010, 011
Emerson
004, 005, 006, 007
Fisher
003, 008, 009, 010
JVC
018, 019
*[ ] : Preset codes set upon shipment from the factory.
Kenwood
011, 012, 013, 014, 017
Magnavox
006, 015, 035
*[ ] : Les codes préréglés diffèrent en fonctiom des livraison de
l’usine.
Marantz
016, 028, 035
MCS
016, 024
Onkyo
025, 027
Optimus
017, 020, 021, 022, 023
Philips
014, 032, 033, 035
Pioneer
006, 022, 030
Sears
006
Sony
023, 031
Teac
002, 009, 028
Technics
016, 029, 036
Wards
035, 037
Yamaha
038, 039, 040, 041
Zenith
042
CDR
Denon
*[111], 112
Philips
112
MD
Denon
113
Kenwood
003, 004
Onkyo
007
Sharp
005
Sony
006
148
DVD preset codes
Codes préréglés DVD
B
Model No.
Modéle numéro
111
DVD-700
DVD-900
DVD-1000
DVD-1400
DVD-1500
DVD-2200
DVD-2800
DVD-2800II
DVD-2900
DVD-3800
DVD-A11
DVD-A1
014
DVD-800
DVD-1600
DVD-2000
DVD-2500
DVD-3000
DVD-3300
MEMO:
149
MEMO:
150
MEMO:
151
16-11, YUSHIMA 3-CHOME, BUNKYO-KU, TOKYO 113-0034, JAPAN
Telephone: (03) 3837-5321
Printed in China 511 4182 000