Sharp 27NS180 Service manual

27N-S100, 27N-S180
CN27S10/14/18
SERVICE MANUAL
S40Z327N-S100
COLOR TELEVISION
Chassis No. SN-91
MODELS
27N-S100, 27N-S180
CN27S10, CN27S14, CN27S18
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its
original condition and only parts identical to those specified should be used.
CONTENTS
Page
» ELECTRICAL SPECIFICATIONS ......................................................................................................... 1
» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2
» LOCATION OF USER'S CONTROL ..................................................................................................... 6
» INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................ 7
» CHASSIS LAYOUT ............................................................................................................................. 13
» BLOCK DIAGRAM .............................................................................................................................. 14
» SCHEMATIC DIAGRAMS ................................................................................................................... 18
» PRINTED WIRING BOARD ASSEMBLIES ........................................................................................ 38
» REPLACEMENT PARTS LIST ............................................................................................................ 42
» PACKING OF THE SET ...................................................................................................................... 51
ELECTRICAL SPECIFICATIONS
POWER INPUT .................................................... 120 V AC 60 Hz
POWER RATING .................................................................. 110 W
PICTURE SIZE ........................................... 2,187cm2 (339sq inch)
CONVERGENCE ............................................................. Magnetic
SWEEP DEFLECTION .................................................... Magnetic
FOCUS ............................................... Hi-Bi-Potential Electrostatic
SPEAKER
SIZE ...................................................................... 8 cm (Round)
VOICE COIL IMPEDANCE ............................. 32 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ..................................................... 75 ohm Unbalanced
TUNING RANGES
VHF-Channels ............................................................... 2 thru 13
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ..................................... 45.75 MHz
UHF-Channels ............................................................ 14 thru 69
Sound IF Carrier Frequency ...................................... 41.25 MHz
CATV Channels ........................................................... 1 thru 125
Color Sub-Carrier Frequency .................................... 42.17 MHz
(EIA, Channel Plan U.S.A.)
(Nominal)
AUDIO POWER
OUTPUT RATING .............. 1.3W + 1.3W (at 10% distortion and
Dual CH Operate)
SHARP CORPORATION
Specifications are subject to change without
prior notice.
This document has been published to be used for after
sales service only.
1 The contents are subject to change without notice.
27N-S100, 27N-S180
CN27S10/14/18
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are throughly
familiar with all safety checks and the servicing guidelines which follow:
WARNING
X-RADIATION AND HIGH VOLTAGE LIMITS
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation. The
only potential source of X-ray in current solid state
TV receivers is the picture tube. However, the picture
tube does not emit measurable X-Ray radiation, if
the high voltage is as specified in the "High Voltage
Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem. Every
time a color chassis is serviced, the brightness should
be tested while monitoring the high voltage with a
meter to be certain that the high voltage does not
exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified or
make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test measurements
on a receiver with excessive high voltage, avoid being
unnecessarily close to the receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
4A 125V
CAUTION: FOR CONTINUED
PROTECTION AGAINST A
RISK OF FIRE, REPLACE
ONLY WITH SAME TYPE 4A125V FUSE.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
2
27N-S100, 27N-S180
CN27S10/14/18
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon and etc.) and measure the AC voltage
drop across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 120 volt AC outlet,
(Do not use an isolation transformer for this test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to earth ground.
• Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
AC
VOLTMETER
1.5k ohm
10W
0.15µF
TEST PROBE
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "å"
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
27N-S100, 27N-S180
CN27S10/14/18
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
LIMITES DES RADIATIONS X ET DE LA
HAUTE TENSION
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
3. Les déversoirs thermiques à semi-conducteurs
peuvent présenter un danger de choc électrique
lorsque le réceqteur est en marche.
4. Le châssis de ce récepteur possède deux systèmes
de masse qui sont séparées par du matériel
d'isolation. Le système de masse non-isolée (sous
tension) est pour le circuit du régulateur de tension
B+ et le circuit de sortie horizontale. Le système de
masse isolée est pour les tensions DC B+ basses et
le circuit secondaire du transformateur haute tension.
Pour éviter tout risque d'électrocution lors de
l'entretien de ce châssis, utiliser un transformateur
d'isolation entre le cordon de ligne et la prise de
courant.
4A 125V
1. Tout le personnel réparateur doit être instruit des
instructions et procédés relatifs aux radiations X.
Le tube-image, seule source de rayons X dons les
téleviseurs transistorisés, n'émet pourtant pas de
rayons mesurables si la haute tension est maintenue
à un niveau préconisé dans la section "Vérification
de la haute tension".
C'est seulement quand la haute tension est excessive
que les rayons X peuvent entrer dans l'enveloppe du
tube-image y compris le conducteur de verre. Il est
important de maintenir la haute tension en-dessous
du niveau spécifié.
2. Il est essentiel que le réparateur ait sous la main un
voltmètre à haute tension qui doit être périodiquement
étalonné.
3. La haute tension doit toujours être maintenue à la
valeur de régime -et pas plus haute. L'opération à
des tensions plus élevées peut entraîner une panne
du tube-image ou du circuit à haute tension et, dans
certaines conditions, peut entraîner une radiation
dépassant les niveaux préscrits.
4. Quand le régulateur à haute tension fonctionne
correctement, il n'y a aucun problème de radiation
X. Chaque fois qu'un châssis couleurs est réparé, la
luminosité doit être examinée bout en contrôlant la
haute tension à l'aide d'un voltmètre pour s'assurer
que la haute tension ne dépasse pas la valeur
spécifiée et qu'elle soit correctement réglée.
5. Ne pas utiliser un tube-image autre que celui spécifié
et ne pas effectuer de modifications déconseillées
du circuit à haute tension.
6. Lors de la recherche des pannes et des mesures
d'essai sur un récepteur qui présente une haute
tension excessive, éviter de s'approcher inutilement
du récepteur.
Ne pas faire fonctionner le récepteur plus longtemps
que nécessaire pour localiser la cause de la tension
excessive.
PRECAUTION: POUR LA
PROTECTION CONTINUE
CONTRE LES RISQUES
D'INCENDIE, REMPLACER LE
FUSIBLE PAR UN FUSIBLE DE
MEME TYPE 4A-125V.
REPARATION DU SYSTEME A HAUTE TENSION ET DU TUBE-IMAGE
Lors de la réparation de ce systéme,
supprimer la charge statique en branchant
une résistance de 10 kΩ en série avec un fil
isolé (comme une sonde d'essai) entre la
mise à la terre du tube-image et le fil
d'anodel. (Le corden d'alimentation doit être
retiré de la prise murale.)
1. Le tube image dans ce récepteur emploie une
protection intégrée contre l'implosion.
2. Par mesure de sécurité, changer le tube-image pour
un tube du même numéro de type.
3. Ne pas lever le tube-image par son col.
4. Ne manipuler le tube-image qu'en porant des lunettes
incassables et qu'après avoir déchargé totalement
la haute tension.
4
27N-S100, 27N-S180
CN27S10/14/18
PRECAUTIONS A PRENDRE LORS DE LA REPARATION
(Suite)
• Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
arbres de commande et des boutons, écusson, etc.)
et mesurer la chute de tension CA en-travers de la
résistance. Toutes les vérifications doivent être
refaites après avoir inversé la fiche du cordon
d'alimentation. (Si nécessaire, une prise d'adpatation
non polarisée peut être utilisée dans le but de terminer
ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme
les boutons de commande non-métalliques, les
isolants, le dos du coffret, les couvercles ou blindages
de réglage et de compartiment, les réseaux de
résistance-capacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
• Brancher le cordon d'alimentation directem-ent à une
prise de courant de 120V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
• A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kΩ 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à
la terre.
• Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
Voltmètre CA
1.5k ohm
10W
0.15µF
SONDE D'ESSAI
AUX PIECES
METALLIQUES
EXPOSEES
TO EXPOSED
METAL PARTS
BRANCHER A UNE
TERRE CONNUE
CONNECT TO
KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentes
à vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
5
27N-S100, 27N-S180
CN27S10/14/18
LOCATION OF USER'S CONTROL
Front Panel
POWER
Press → On.
Press again → Off.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
VIDEO/AUDIO IN 2 TERMINALS
(VIDEO/AUDIO terminals are also
provided on the rear.)
SENSOR AREA FOR
REMOTE CONTROL
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Press both at same time to
access MAIN MENU Screen.
Basic Remote Control Functions
Infrared Transmitter Window
POWER
Press → On.
Press again → Off.
REMOTE KEYPAD
Accesses any channel from keypad.
+
FLASHBACK
Returns to previous channel.
DISPLAY
Press → Displays receiving channel for
four seconds.
Press again → Removes display.
• Temporarily displays receiving
channel when in Closed Caption
mode.
INPUT
Press → Switch to external video
INPUT 1 mode.
Press again → Switch to external video
INPUT 2 mode.
Press three times → Switch back to the
original TV mode.
PERSONAL PREFERENCE
With the Personal Preference buttons,
you can program your favorite
programs by using the four categories
A, B, C and D. The channels can be
accessed quickly by using these
buttons.
ENTER
Used in some instances where a VCR
or Cable Converter Box requires an
“enter” command after selecting
channels, when using the REMOTE
KEYPAD button.
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
• In menu mode, changes or selects
the TV adjustments.
MENU
Press → Accesses MAIN MENU.
Press again → Exits MAIN MENU.
CHANNEL UP/DOWN
(') Selects next higher channel.
(") Selects next lower channel.
• Moves the “ ” mark of the MENU
screens.
TV-CATV MODE SELECT SWITCH
In TV position, sends power and
channel select commands (Channel
up/down and Random Access buttons)
to the TV.
In CATV position, sends power and
channel select commands to a cable
TV converter.
MUTE
Press → Mutes sound.
Press again → Restores sound.
• CLOSED CAPTION appears when
sound is muted.
VCR CONTROL
NOTE:
• The above shaded buttons on the Remote Control glow in the dark. To use the glow-in-the-dark display on the
remote control, place it under a fluorescent light or other lighting.
• The phosphorescent material contains no radioactive or toxic material, so it is safe to use.
• The degree of illumination will vary depending on the strength of lighting used.
• The degree of illumination will decrease with time and depending on the temperature.
• The time needed to charge the phosphorescent display will vary depending on the surrounding lighting.
• Sunlight and fluorescent lighting are the most effective when charging the display.
6
27N-S100, 27N-S180
CN27S10/14/18
INSTALLATION AND SERVICE INSTRUCTIONS
Note:
(1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
CIRCUIT PROTECTION
HIGH VOLTAGE CHECK
The receiver is protected by a 4.0A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
X-RADIATION PROTECTOR CIRCUIT TEST
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 120V AC
line voltage, with a strong air signal or a properly tuned
in test signal.
3. Enter the service mode and select the service
adjustment "S19" and Bus data "01" (Y-mute on).
4. The voltage should be approximately, 28.7kV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 120V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to TP653 and make sure
that the voltmeter reads 11.2 ± 0.6V.
5. Apply external 13.8V DC at TP653 by using an
external DC supply, TV must shut off.
6. To reset the protector, unplug the AC cord and make
a short circuit between TP651 and TP652. Now make
sure that normal picture appears on the screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
7
27N-S100, 27N-S180
CN27S10/14/18
For adjustments of this model, the bus data is converted to various analog signals by the D/A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.
1. Service mode
To enter the service mode and exit service mode.
Before putting unit into the service mode, check that
customer adjustments are in the normal mode. Use
the reset function in the video adjustment menu to
ensure customer controls are in their proper (reset)
position.
While pressing the Vol-up and Ch-up buttons at the
sametime, plug the AC cord into a wall socket.
Now the TV set is switched on and enters the service
mode.
To exit the service mode, turn the television off by
pressing the power button.
2. Service number selection
Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set.
The service adjustment number will vary in
increments of one, from "S01" to "M05". Select the
item you wish to adjust.
3. Data number selection
Press the Vol-up or down button to adjust the data
number.
DATA NUMBER
CHANNEL
SERVICE ADJUSTMENT NUMBER
S01
55(085)
02
S01 D:00
Figure A.
8
27N-S100, 27N-S180
CN27S10/14/18
SERVICE
NUMBER
DATA
ADJUSTMENT ITEM
ADJUSTMENT CONTENTS
RANGE
INITIAL VALUE
S01
S02
S03
S04
S05
S06
S07
S08
S09
S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
OP1
PICTURE
TINT
COLOR
BRIGHTNESS
SHARPNESS
VERTICAL PHASE
HORIZONTAL PHASE
RF-AGC
VERTICAL AMP
PIF VCO
R CUT-OFF
G CUT -OFF
B CUT-OFF
G GAIN
B GAIN
TRAP
BALANCE
C.C.POSITION
MUTE
ENERGY SAVE OFFSET
D.D.E. OFFSET
OSD SETUP
TUNER SETUP
OPTION1 (Set to each mode)
55
46
32
40
28
00
12
23
20
2C
00
00
00
7F
7F
00
20
17
00
20
03
00
00
00
00-7F
00-7F
00-7F
00-7F
00-3F
00-07
00-1F
00-3F
00-3F
00-7F
00-FF
00-FF
00-FF
00-FF
00-FF
00 or 01
00-3F
00-7F
00,01,03
00-3F
00-1F
00-03
00, 01
00-FF
OP2
OPTION2
00
00-FF
M01
M02
M03
M04
M05
INPUT LEVEL
ST VCO
FILTER
WIDE BAND
SPECTRAL
0A
20
1C
20
1B
00-0F
00-3F
00-3F
00-3F
00-3F
Must be set to "28"
Must be set to "00"
Must be set to "00"
Must be set to "20"
"00"=Normal, "01"=No-Y, "03"=No Vertical
Must be set to "23"
Must be set to "03"
Must be set to "00"
Must be set to "00"
"B3"=27N-S100, "B7"=27N-S180,
"A7"=CN27S10, "A7"=CN27S14, "A7"=CN27S18
"A7"=27N-S100, "A7"=27N-S180,
"07"=CN27S10, "A7"=CN27S14, "A7"=CN27S18
Table - A
Holding down both the Vol-up/CH-down buttons on the TV set at service mode for more than 2 seconds will
automatically write the above initial values into IC2101.
ADJUSTMENT
NOTES
PART REPLACED
NECESSARY
X
IC2001
IC201
Data is stored in IC2101.
The adjustment is needed to compensate for characteristics
of parts including IC201 and MTS level (M01).
X
IC2101
X
CRT
X
X
IC3001
UNNECESSARY
Holding down both the Vol-up/CH-down buttons on the TV
set in the service mode for more than 2 seconds will
automatically write the above initial values into IC2101. Then
perform a complete adjustment.
Adjust items related to picture tube only.
Adjust items related to MTS only (M01~M05).
Table - B
9
27N-S100, 27N-S180
CN27S10/14/18
SERVICE ADJUSTMENT
VCO Adjustment
White Balance Adjustment
1. Connect a digital voltmeter between pin (44) of IC201
and ground.
2. Receive a good local channel.
3. Enter the service mode and select the service
adjustment "S10".
4. Adjust the data so that digital voltmeter reads 2.2V.
5. Adjustment is completed, remove the voltmeter,
return to "normal" mode.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S03" and set to "00" (minimum
color)(Record original data code under adjustment
"S03" before changing). "S03" does not have to be
adjusted, if you selected a B/W picture or monoscope
pattern.
3. Alternately adjust the service adjustment data of "S14"
and "S15" until a good grey scale with normal whites
is obtained.
4. Select the service adjustment "S03" and adjust data
to obtain normal color level.
RF AGC Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S08".
3. Set the data value to point where no noise or beat
appears.
4. Select another channel to confirm that no noise or
beat appears.
Note 1 : You will have to come out of the service
mode to select another channel.
Note 2 : Setting the data to "00" will produce a black
raster.
Sub-Picture Adjustment
1. Receive a good local channel.
2. Make sure the customer picture control is set to
maximum.
3. Enter the service mode and select the service
adjustment "S01".
4. Adjust the data value to achieve normal contrast
range.
Screen Adjustment
Sub-Tint Adjustment
1. Connect a oscilloscope between TP854 and GND
on the CRT Unit.
2. Receive a good local channel.
3. Enter the service mode and select the service
adjustment "S03" and set the data value to "00" to
set the color level to minimum. (Record original data
code under adjustment "S03" before changing) You
may skip this step, if you selected a B/W picture or
monoscope pattern.
4. Select the service adjustment "S19" and adjust the
data value to "01", this turn off the luminance signal
(Y-mute).
5. Select the service adjustment "S04" and adjust data
value to obtain 2.35 volts on the oscilloscope screen.
6. Adjust the master screen control until the raster
darkens to the point where raster is barely seen.
7. Adjust the service adjustments "S11" red, "S12" green
and "S13" blue to obtain a good grey scale with
normal whites at low brightness level.
8. Select the service adjustment "S19" and reset data
to "00". Select the service adjustment "S03" and reset
data to obtain normal color level.
9. Remove oscilloscope, and reset the master screen
control to obtain normal brightness range.
1. Receive a good local channel.
2. Set customer tint control to center of it's range.
3. Enter the service mode and select the service
adjustment "S02".
4. Adjust "S02" data value to obtain normal flesh tones.
Sub-Color Adjustment
1. Receive a good local channel.
2. Make sure the customer color control is set to center
position .
3. Enter the service mode and select service adjustment
"S03".
4. Adjust "S03" data value to obtain normal color level.
10
27N-S100, 27N-S180
CN27S10/14/18
Sub-Brightness Adjustment
3.58MHz Trap Adjustment
1. Receive a good local channel.
2. Make sure the customer brightness control is set to
center position.
3. Enter the service mode and select the service
adjustment "S04".
4. Adjust "S04" data value to obtain normal brightness
level.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S16".
3. This is a two position adjustment, "00" is ON, "01" is
OFF.
4. Models should be adjusted as follows.
Vertical-Size Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S09".
3. While observing the top and bottom of the screen,
adjust "S09" data value to proper vertical size.
MODEL
"S16"
27N-S100
01
27N-S180
01
CN27S10
00
CN27S14
01
CN27S18
01
Sharpness and Audio Balance Adjustments
Vertical Phase Adjustment
1. Enter the service mode and select the service
adjustment "S06".
2. Adjust data value to "00".
Note: This must be set "00" when changed data retrace
line will appear.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustments "S05" for sharpness and "S17" for
balance.
» Sharpness Adjustment
3. Adjust data value to "28"(center of data range) for
sharpness adjustment.
» Audio Balance Adjustment
4. Adjust data value to "20"(center of data range) for
audio balance adjustment.
Horizontal Position Adjustment
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S07".
3. Adjust "S07" data value so that picture is centered.
Energy save offset Adjustment
Caption Position Adjustment (Horizontal)
1. Enter the service mode and select the service
adjustment "S20".
2. Adjust data value to "23".
Note : This position is used to preset the level for the
energy save function.
1. Receive a good local channel.
2. Enter the service mode and select the service
adjustment "S18".
3. A black text box appears on the screen. (see Figure
B. below)
4. Adjust "S18" data value so that text box is positioned
in the center of the screen.
Other Adjustments
1. Enter the service mode.
2. Adjust the following data values as listed below.
Figure B.
11
S21
"03"
DDE OFFSET
S22
"00"
OSD SETUP
S23
"00"
TUNER SETUP
27N-S100, 27N-S180
CN27S10/14/18
MTS ADJUSTMENT
MTS Level Adjustment
1. Feed the following monaural signal to pin (14) of
IC3001.
Monaural signal : 300Hz, 245mVrms
2. Connect the rms voltmeter to pin (39) of IC3001.
3. Enter the service mode and select the service
adjustment "M01".
4. Adjust the data so that the rms voltmeter reads.
Spec.: 490 ±10mVrms.
MTS VCO Adjustment
1. Keep the unit in no-signal state.
2. Connect the frequency counter to pin (39) of IC3001.
3. Connect a capacitor (100µF, 50V) in between
positive(+) side of C3005 and ground.
4. Enter the service mode and select the service
adjustment "M02"
5. Adjust the data so that the frequency counter reads.
Spec.: 62.94 ±0.75kHz.
Filter Adjustment
1. Feed the following stereo pilot signal to pin (14) of
IC3001 .
Stereo pilot signal: 9.4kHz, 600mVrms.
2. Enter the service mode and select the service
adjustment "M03".
3. Adjust the data at the point where "OK" appears on
the screen. The "OK" represents the approximate
center of the adjustable range of the data.
Separation Adjustment
1. Connect the rms voltmeter to pin (39) of IC3001.
2. Receive the following composite stereo signal 1.
Composite stereo signal: 30% modulation, left
channel only, noise reduction on, 300Hz
3. Enter the service mode and select the service
adjustment "M04".
4. Adjust the data until the AC voltage reading of the
rms voltmeter is minimum.
5. Receive the following composite stereo signal 2.
Stereo signal: 30% modulation, left channel only,
noise reduction on, 3kHz
6. Enter the service mode and select the service
adjustment "M05".
7. Adjust the data until the AC voltage reading of the
rms voltmeter is minimum.
8. Take the above steps 1 thru 8 again for fine
adjustment.
12
27N-S100, 27N-S180
CN27S10/14/18
CHASSIS LAYOUT
H
PWB-B
(27N-S180, CN27S18)
PWB-K
(27N-S100, CN27S14)
PWB-K
G
PWB-H
PWB-A
F
E
D
C
B
A
10
11
1
12
2
13
143
15
13
4
16
17 5
18
6 19
27N-S100, 27N-S180
CN27S10/14/18
MODEL 27N-S100 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
1
2
2
3
4
3
5
64
14
7
5
8
9
6
10
27N-S100, 27N-S180
CN27S10/14/18
MODELS 27N-S180, CN27S18 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
10
11
1
12
2
13
143
15
15
4
16
17 5
18
6 19
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S10 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
1
1
2
2
3
4
3
5
64
16
7
5
8
9
6
10
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S14 BLOCK DIAGRAM
H
G
F
E
D
C
B
A
10
11
1
12
2
13
143
15
17
4
16
17 5
18
6 19
27N-S100, 27N-S180
CN27S10/14/18
DESCRIPTION OF SCHEMATIC DIAGRAM
WAVEFORM MEASUREMENT CONDITIONS:
1. Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
NOTES:
H
1. The unit of resistance "ohm" is omitted.
(K=kΩ=1000Ω, M=MΩ)
2. All resistors are 1/8 watt, unless otherwise noted.
3. All capacitors are µ F, unless otherwise noted.
(P=pF=µµF)
4. (G) indicates ±2% tolerance may be used.
5.
indicates line isolated ground.
G
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000µ V B & W or Color
F signal.
å AND SHADED (
) COMPONENTS
= SAFETY RELATED PARTS.
' MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES å ET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE ' : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
E
WAVE FORMS
D
C
B
A
1
2
3
4
5
6
18
7
8
9
10
27N-S100, 27N-S180
CN27S10/14/18
SCHEMATIC DIAGRAM: CRT and FRONT AV Units
H
G
F
E
D
C
B
A
10
11
1
12
2
13
143
15
19
4
16
17 5
18
6 19
27N-S100, 27N-S180
CN27S10/14/18
MODEL 27N-S100 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
E
D
C
B
A
1
2
3
20
4
5
6
7
8
9
10
11
21
12
27N-S100, 27N-S180
CN27S10/14/18
MODEL 27N-S100 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
E
D
C
B
A
1
2
3
22
4
5
6
7
8
9
10
11
23
12
27N-S100, 27N-S180
CN27S10/14/18
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
E
D
C
B
A
1
2
3
24
4
5
6
7
8
9
10
11
25
12
27N-S100, 27N-S180
CN27S10/14/18
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
E
D
C
B
A
1
2
3
26
4
5
6
7
8
9
10
11
27
12
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S10 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
E
D
C
B
A
1
2
3
28
4
5
6
7
8
9
10
11
29
12
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S10 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
E
D
C
B
A
1
2
3
30
4
5
6
7
8
9
10
11
31
12
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S14 SCHEMATIC DIAGRAM: MAIN-1 Unit
H
G
F
E
D
C
B
A
1
2
3
32
4
5
6
7
8
9
10
11
33
12
27N-S100, 27N-S180
CN27S10/14/18
MODEL CN27S14 SCHEMATIC DIAGRAM: MAIN-2 Unit
H
G
F
E
D
C
B
A
1
2
3
34
4
5
6
7
8
9
10
11
35
12
27N-S100, 27N-S180
CN27S10/14/18
MODELS 27N-S100, CN27S14 SCHEMATIC DIAGRAM: S-VIDEO Unit
H
G
F
E
D
C
B
A
1
2
3
4
36
5
6
27N-S100, 27N-S180
CN27S10/14/18
MODELS 27N-S180, CN27S18 SCHEMATIC DIAGRAM:
DIGICOM/S-VIDEO Unit
H
G
F
E
D
C
B
A
1
2
3
4
37
5
6
27N-S100, 27N-S180
CN27S10/14/18
PRINTED WIRING BOARD ASSEMBLIES
H
G
F
E
D
C
B
A
PWB-A : MAIN Unit (Wiring Side)
1
2
3
4
38
5
6
27N-S100, 27N-S180
CN27S10/14/18
H
G
F
E
D
C
B
A
PWB-A : MAIN Unit (Chip Parts Side)
1
2
3
4
39
5
6
27N-S100, 27N-S180
CN27S10/14/18
H
G
F
E
PWB-B : CRT Unit (Wiring Side)
D
C
B
PWB-H : FRONT AV Unit (Wiring Side)
A
1
2
3
4
40
5
6
27N-S100, 27N-S180
CN27S10/14/18
D1503
6
C1509
C1512
5
J6
5
P1502
P1501
F
1
KB
C1511
1
KC
D1501
D1504
KA
1
C1513
J3
R1514
C1507
C1506
C1505
C1504
R1518
R1519
D1502
R1516
J4
J5
C1501
R1517R1515
J1
C1508
C1503
L1503
L1501
R1509
R1508
R1507
Q1502
R1504
IC1501
R1510
Q1501
L1502
J2
R1513
R1512
R1511
R1502
G
C1510
Q1504
P1503
Q1503
R1501
R1505
C1502
R1506
R1503
H
PWB-K : S-VIDEO Unit (Wiring Side)
Q1406
Q1403
R1419
R1417
C1417
C1454
1
C1451
IC1451
R1414
C1421
C1412
C1410
R1408
R1407
R1418
R1415
C1423
RJ5
R1454
R1416
C1424
C1411
Q1404
R1413
R1425
C1406
RJ1
C1409
CJ1
C1407
C1420
C
Q1405
C1413
R1412
C1405
IC1401
R1409
C1404
1
C1416
R1451
R1455
C1403
C1425
1
1
R1424
C1453
D
R1452
R1420
(Only for 27N-S100, CN27S14)
E
R1403
RJ3
RJ2
Q1401
RJ4
R1410
R1453
C1428
1
R1422
R1404
R1405
R1406
C1401
R1401
R1402
B
1
C1426
Q1402
Q1407
R1421
PWB-K : DIGICOM/S-VIDEO Unit (Wiring Side)
A
(Only for 27N-S180, CN27S18)
1
2
3
4
41
5
6
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
Ref. No.
★
Part No.
Description
Code
PARTS LIST
LISTE DES PIECES
PARTS REPLACEMENT
CHANGE DES PIECES
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les
pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep
éler élee par la marque å et sont hachur élees dans les listes de
pi`eces et dans les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr
éLesente pas les m éoemes caract éLeristiques de s élecurit éle que
la pi`ece recommand élee parl'usine et dans ce manuel de service,
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER
2. REF. NO.
3. PART NO.
4. DESCRIPTION
in USA:
Ref. No.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
V101
L703
2. NO. DE REF
3. NO. DE PIECE
4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
★ MARK: SPARE PARTS-DELIVERY SECTION
★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
▲ MARK: X- RAY RELATED PARTS
▲ MARQUE: PIECES RELATIVE AUX RAYONS X
Part No.
★
Description
Ref. No.
Code
VB68ADT2503*S
RCiLG0038MEZZ
MSPRT0002MEZZ
QEARC2702MEZZ
M
M
M
M
Picture Tube (I.T.C.)
Degaussing Coil
Spring for CRT
Grounding Part
★
Part No.
Description
Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
PICTURE TUBE
çå
å
1. NUMERO DU MODELE
MAIN UNIT
CN
AQ
AA
AH
TUNER
NOTE: THE PARTS HERES SHOWN ARE SUPPLIED
AS AN ASSEMBLY BUT NOT INDEPENEDENTLY.
å TU51 VTUVTST5UF78S M Tuner
AX
or
VTU115B8035AH
INTEGRATED CIRCUITS
IC101
çå IC201
IC351
IC352
å IC501
å IC701
å IC702
PRINTED WIRING BOARD ASSEMBLIES
VHiKA78S05P-1
RH-iX3253CEZZ
VHiAN7511//-1
VHiAN7511//-1
VHiTA8427K/-1
VHiSTRF66261E
RH-FX0034CEZZ
or
RH-FX0002GEZZ
VHiSE120N//-1
VHiKA7809Pi-1
VHiKA7809Pi-1
VHiMM1111XF1E
J
J
J
J
J
J
J
KA78S05P
TA1268AN
I.C.
I.C.
TA8427K
STR-F6626
PC817
J
M
M
J
IC951 VHiMM1113XF1E
J
IC2001 RH-iX3366CEZZ
IC2040 VHiKiA7045A-1
IC2101 VHiM24C16B/-1
IC3001 VHiCXA2074Q-1
M
J
J
J
SE120N
AG
KA7809PI
AE
KA7809PI
AE
MM1111XFBE
AE
(CN27S10)
MM1113XFBE
AE
(27N-S100/180, CN27S14/18)
TMPA8700CPF-164
AT
KIA7045A
AD
M24C16-BN6
AG
CXA2074Q
AY
(NOT REPLACEMENT ITEM)
PWB-A DUNTKA126WEK4 – MAIN Unit (27N-S100)
PWB-A DUNTKA126WEK5 – MAIN Unit
(27N-S180, CN27S18)
PWB-A DUNTKA126WEK8 – MAIN Unit (CN27S10)
PWB-A DUNTKA126WEL6 – MAIN Unit (CN27S14)
PWB-B DUNTK9510WEK1 – CRT Unit
PWB-H DUNTK9310WEK1 – FRONT AV Unit
PWB-K DUNTKA114WEK0 – S-VIDEO Unit
(27N-S100, CN27S14)
PWB-K DUNTKA115WEK0 – DIGICOM/S-VIDEO Unit
(27N-S180, CN27S18)
å
å
å
—
—
—
—
—
—
—
—
IC703
IC750
IC751
IC951
AD
AV
AK
AK
AL
AX
AE
TRANSISTORS
You can substitute "VS2SC2412-C-1" for "VS2SD601AR/-1".
Q201 VS2SC2735//1E
J 2SC2735
AC
Q251 VS2SD601AR/-1
J 2SD601AR
AC
(27N-S180, CN27S18)
42
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
D753
D754
D755
å D756
D2001
D2011
å
å
MAIN UNIT (Continued)
Q252
VS2SD601AR/-1
Q253
VS2SD601AR/-1
Q301
Q401
Q402
Q601
å Q602
Q751
Q901
VS2SD601AR/-1
VS2SD601AR/-1
VS2SB709AR/-1
or
VS2SA1037KR-1
VS2SD601AR/-1
VS2SB709AR/-1
or
VS2SA1037KR-1
VS2SB709AR/-1
or
VS2SA1037KQ-1
VS2SC2482//-1
VS2SD2539//1E
VS2SC3198-Y-1
VS2SD601AR/-1
Q902
VS2SD601AR/-1
J
Q903
VS2SD601AR/-1
J
Q904
VS2SD601AR/-1
J
Q2060 VS2SD601AR/-1
Q2201 VS2SD601AR/-1
Q2211 VS2SD601AR/-1
J
J
J
Q403
Q421
Q451
J 2SD601AR
(27N-S180, CN27S18)
J 2SD601AR
(27N-S180, CN27S18)
J 2SD601AR
J 2SD601AR
J 2SB709AR
AC
J 2SD601AR
J 2SB709AR (CN27S10)
AC
AC
J 2SB709AR
AC
Part No.
RH-DX0441CEZZ
RH-DX0441CEZZ
VHD1SS119//-1
RH-DX0441CEZZ
VHD1SS119//-1
RH-EX0611GEZZ
★
Description
J
J
J
J
J
J
Diode
Diode
Diode
Diode
Diode
Zener Diode, 5.1V
Code
AC
AC
AB
AC
AB
AA
PACKAGED CITCUITS
AC
å
AC
AC
AC
PR701 RMPTP0092CEZZ J Packaged Circuit
X801 RCRSB0205CEZZ J Crystal
or
RCRSB0001PEZZ
AH
AF
FILTERS
J
J
J
J
CF301 RFiLC0029TAZZ
CF401 RFiLC0013CEZZ
CF631 RFiLA0034CEZZ
CF2040 RFiLC0121GEZZ
or
RFiLA0099CEZZ
SF201 RFiLC0405CEZZ
2SC2482
AD
2SD2539
AP
2SC3198(Y)
AA
2SD601AR
AC
(27N-S180, CN27S10/14/18)
2SD601AR
AC
(27N-S180, CN27S10/14/18)
2SD601AR
AC
(27N-S180, CN27S10/14/18)
2SD601AR
AC
(27N-S180, CN27S10/14/18)
2SD601AR
AC
2SD601AR
AC
2SD601AR
AC
J
J
J
J
Ceramic Filter
Ceramic Filter
Ceramic Filter
Ceramic Filter
J SAW Filter
AD
AE
AD
AD
AH
COILS
L201
L202
L251
L301
L302
VP-XF1R2K0000
RCiLi0588CEZZ
VP-XF390K0000
VP-XF8R2K0000
RCiLi0613CEZZ
or
RCiLi0605CEZZ
L401 VP-XF6R8K0000
L402 VP-XF3R3K0000
L403 VP-XF8R2K0000
L404 VP-XF8R2K0000
L421 VP-XF680K0000
L672 RCiLZ0101MEZZ
or
RCiLZ0102MEZZ
å L701
RCiLF0025PEZZ
å L702
RCiLF0025PEZZ
å L705
RCiLP0179CEZZ
L729 RCiLP0179CEZZ
L2040 RCiLB0131CEZZ
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D51
RH-EX0611GEZZ J Zener Diode, 5.1V
AA
D52
RH-EX0673GEZZ J Zener Diode, 32V
AB
D53
RH-EX0611GEZZ J Zener Diode, 5.1V
AA
D103 VHD1SS119//-1
J Diode
AB
D401 VHD1SS119//-1
J Diode
AB
D402 RH-EX0604GEZZ J Zener Diode, 3.9V
AB
D454 RH-EX0611GEZZ J Zener Diode, 5.1V
AA
D455 VHD1SS119//-1
J Diode
AB
D456 VHD1SS119//-1
J Diode
AB
D457 RH-EX0217CEZZ J Zener Diode
AB
D458 RH-EX0217CEZZ J Zener Diode
AB
D459 VHD1SS119//-1
J Diode
AB
å D501 RH-DX0131CEZZ
J Diode
AC
å D510 RH-DX0441CEZZ
J Diode
AC
D621 RH-EX0631GEZZ J Zener Diode, 9.1V
AA
å D622 RH-DX0131CEZZ
J Diode
AC
çå D651 RH-DX0131CEZZ
J Diode
AC
çå D652 RH-EX1313CEZZ M Zener Diode, 9.1V
AB
çå D653 VHD1SS119//-1
J Diode
AB
çå D654 VHD1SS119//-1
J Diode
AB
å D701 RH-DX0154CEZZ
J Diode
AC
å D702 RH-DX0154CEZZ
J Diode
AC
å D703 RH-DX0154CEZZ
J Diode
AC
å D704 RH-DX0154CEZZ
J Diode
AC
D705 VHD1SS82///1A
J Diode
AC
D706 RH-DX0066GEZZ J Diode
AB
D707 VHD1SS82///1A
J Diode
AC
D708 RH-DX0066GEZZ J Diode
AB
å D709 RH-DX0229CEZZ
J Diode
AF
å D712 RH-DX0407CEZZ
J Diode
AD
å D713 RH-EX0673GEZZ
J Zener Diode, 32V
AB
å D715 RH-EX0610GEZZ
J Zener Diode
AA
D716 VHD1SS119//-1
J Diode
AB
D717 RH-EX0650GEZZ J Zener Diode, 16V
AB
å D725 RH-DX0407CEZZ
J Diode
AD
å D751 RH-DX0441CEZZ
J Diode
AC
å D752 RH-DX0441CEZZ
J Diode
AC
J
J
J
J
J
Peaking 1.2µH
VCO Coil
Coil (27N-S180, CN27S18)
Peaking 8.2µH
IF Coil
AB
AF
AB
AB
AE
J
J
J
J
J
M
Peaking 6.8µH
Peaking 3.3µH
Peaking 8.2µH
Peaking 8.2µH
Peaking 68µH (CN27S10)
Coil
AB
AB
AB
AB
AB
AE
M
M
J
J
J
Coil
Coil
Coil
Coil
Oscillation Coil
AK
AK
AD
AD
AE
TRANSFORMERS
T601
çå T602
å
å
T701
T702
RTRNZ0057PEZZ
RTRNF0033MEZZ
or
RTRNF0037MEZZ
RTRNP0543CEZZ
RTRNZ0017MEZZ
or
RTRNZ0022MEZZ
R Transformer
M H-Volt Transformer
AK
AY
J Power Transformer
M Transformer
AM
AM
CAPACITORS
[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]
C51
VCEA0A1CW476M J 47
16V
EL.
C53
VCEA0A1HW105M J 1
50V
EL.
C54
VCEA0A1HW475M J 4.7
50V
EL.
C55
VCEA0A1CW108M J 1000 16V
EL.
C56
VCKYCY1CB104K J 0.1
16V
Ceramic
C103 VCEA0A1CW228M J 2200 16V
EL.
C201 VCKYMN1HB102K J 1000p 50V
Ceramic
C202 VCKYCY1HF103Z J 0.01
50V
Ceramic
C203 VCKYCY1HB102K J 1000p 50V
Ceramic
C204 VCKYCY1HF103Z J 0.01
50V
Ceramic
C205 VCEA0A1HW474M J 0.47
50V
EL.
C206 VCEA0A1CW337M J 330
16V
EL.
C207 VCKYCY1HF103Z J 0.01
50V
Ceramic
C208 VCEA0A1HW474M J 0.47
50V
EL.
C209 VCKYCY1HB222K J 2200p 50V
Ceramic
C210 VCKYCY1HB102K J 1000p 50V
Ceramic
C251 VCQYTA1HM103K J 0.01
50V
Mylar
(27N-S180, CN27S18)
43
AB
AB
AB
AD
AB
AB
AA
AA
AA
AA
AB
AC
AA
AB
AA
AA
AB
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
Ref. No.
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
C252
C253
C301
C302
C303
C307
C308
C309
C313
C351
C352
C354
C355
C356
C358
C359
C401
C402
C403
C404
C405
C406
C408
C409
C410
C411
C412
C413
C414
C421
C422
C451
C452
C453
C501
C502
C510
C511
C512
C513
C514
C515
C516
C517
C518
C551
C552
C606
C607
çå C610
çå C611
C615
å C623
C631
C632
C633
C652
C653
C680
C682
å C701
VCQYTA1HM103K J 0.01
50V
Mylar
(27N-S180, CN27S18)
VCCCCY1HH470J M 47
50V
Ceramic
(27N-S180, CN27S18)
VCCCCY1HH330J J 33p
50V
Ceramic
VCCCCY1HH151J J 150p 50V
Ceramic
VCCCCY1HH390J J 39p
50V
Ceramic
VCCCCY1HH1R5C J 1.5p
50V
Ceramic
VCKYCY1HB102K J 1000p 50V
Ceramic
VCEA0A1CW337M J 330
16V
EL.
VCEA0A1CW476M J 47
16V
EL.
VCEA0A1HW106M J 10
50V
EL.
VCKYCY1HB332K J 3300p 50V
Ceramic
VCEA0A1HW106M J 10
50V
EL.
VCKYCY1HB332K J 3300p 50V
Ceramic
VCEA0A1HW106M J 10
50V
EL.
VCEA0A1CW477M J 470
16V
EL.
VCEA0A1HW106M J 10
50V
EL.
VCKYCY1HB331K J 330p 50V
Ceramic
VCCCCY1HH101J J 100p 50V
Ceramic
VCKYCY1CB104K J 0.1
16V
Ceramic
VCEA0A1HW106M J 10
50V
EL.
VCEA0A1HW335M J 3.3
50V
EL.
VCEA0A1HW225M J 2.2
50V
EL.
VCEA0A1HW106M J 10
50V
EL.
VCEA0A1HW335M J 3.3
50V
EL.
VCQYTA1HM104K J 0.1
50V
Mylar
VCEA0A1CW337M J 330
16V
EL.
VCKYCY1HB103K J 0.01
50V
Ceramic
VCKYCY1HB103K J 0.01
50V
Ceramic
VCKYCY1CB104K J 0.1
16V
Ceramic
(CN27S10)
VCCCCY1HH330J J 33p
50V
Ceramic
(CN27S10)
VCEA0A1CW476M J 47
16V
EL.
VCQYTA1HM104K J 0.1
50V
Mylar
VCEA0A1HW475M J 4.7
50V
EL.
VCEA0A1CW226M J 22
16V
EL.
VCKYPA2HB102K J 1000p 500V Ceramic
VCEA0A1VW108M J 1000 35V
EL.
VCFYSA1JB564J M 0.56
63V
Mylar
VCKYPA2HB391K J 390p 500V Ceramic
VCQYTA1HM473K J 0.047 50V
Mylar
VCQYTA1HM103K J 0.01
50V
Mylar
VCEA0A1VW107M J 100
35V
EL.
VCEA0A1HW474M J 0.47
50V
EL.
VCSATA1VE684K J 0.68
35V
Tantalum
VCEA0A1VW108M J 1000 35V
EL.
VCFYSA1JB473J M 0.047 63V
Mylar
VCSATA1CE225K J 2.2
16V
Tantalum
VCEA0A1HW225M J 2.2
50V
EL.
VCKYPA2HB561K J 560p 500V Ceramic
VCKYPA1HB472K J 4700p 50V
Ceramic
VCFPVC3CA772H J 7700p 1.6kV M-Poly.
VCFPVC3CA772H J 7700p 1.6kV M-Poly.
VCKYPA2HB102K J 1000p 500V Ceramic
VCEA4A2EN106M J 10
250V EL.
VCEA0A1HW335M J 3.3
50V
EL.
VCQYTA1HM103K J 0.01
50V
Mylar
VCEA0A1CW477M J 470
16V
EL.
VCEA0A1HW106M J 10
50V
EL.
VCEA0A1HW106M J 10
50V
EL.
VCFPVC2DB474J M 0.47
200V M-Poly.
VCKYPA2HB331K J 330p 500V Ceramic
RC-FZ012SCEZZ J 0.22
AC250V Plastic
or
RC-FZ012SGEZZ
or
RC-FZ037SCEZZ
å
C706
C707
C708
C709
C710
C717
C718
C722
C723
C725
C726
C727
C729
C730
C731
C732
C741
C742
C753
C755
C772
C801
C802
C803
C804
C805
C806
C807
C808
C901
VCEA0A1HW335M J
C902
VCEA0ACW476M
C903
VCEA0A1HW335M J
C908
C909
C910
VCEA0A1HW225M J
VCEA0A1HW225M J
VCKYCY1HB681K J
C911
VCKYCY1HB681K J
C922
VCEA0A1HW335M J
C923
VCEA0A1HW335M J
C931
VCKYCY1EB183K J
C932
VCKYCY1EB183K J
C951
C952
C954
C955
C956
VCEA0A1HW106M
VCEA0A1HW106M
VCKYCY1HF103Z
VCEA0A1CW106M
VCEA0A1CW106M
J
J
J
J
J
C2001
C2002
C2040
C2041
C2060
C2061
C2062
C2201
C2202
C2601
VCCCCY1HH101J
VCCCCY1HH101J
VCEA0A1AW107M
VCEA0A1HW105M
VCKYCY1CB104K
VCCCCY1HH101J
VCEA0A1AW107M
VCKYCY1HB152K
VCCCCY1HH390J
VCEA0A1HW475M
J
J
J
J
J
J
J
J
J
J
C702
C703
C705
AA
å
å
å
å
å
AA
AB
AC
AB
AB
AA
AD
AB
AA
AB
AB
AC
AB
AC
AD
AA
AB
AB
AA
AA
AF
AF
AA
AD
AB
AB
AC
AB
AB
AE
AA
AD
44
★
or
RC-FZ017SCEZZ
RC-KZ0029CEZZ
RC-KZ0029CEZZ
RC-EZ0800CEZZ
or
RC-EZ0719CEZZ
or
RC-EZ1336CEZZ
RC-KZ0092GEZZ
VCFPVC3CA222H
VCCSPA1HL471J
VCEA0A1VW107M
VCQYTA1HM102J
VCKYPA2HB472K
VCKYPA2HB472K
VCQYTA1HM104K
RC-EZ0724CEZZ
RC-EZ0809CEZZ
RC-KZ0338CEZZ
RC-KZ0338CEZZ
VCEA0A1CW106M
RC-EZ0385CEZZ
RC-EZ0385CEZZ
VCKYPA2HB102K
VCKYPA2HB102K
VCKYPA2HB102K
VCEA0A1CW107M
VCEA0A1CW476M
VCEA0A1VW477M
VCQYTA1HM223K
VCEA0A1HW474M
VCCCCY1HH110J
VCKYCY1CB104K
VCKYCY1CB104K
VCKYCY1CB104K
VCCCCY1HH221J
VCKYCY1HB102K
AB
AA
AA
AA
AD
AA
AC
AB
AB
AA
AB
AA
AB
AC
AB
AA
AA
AB
AB
AB
AB
AB
AB
AC
AC
AA
AA
AB
Part No.
Description
J 0.01
J 0.01
J 560
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
AC250V Ceramic
AC250V Ceramic
200V EL.
Code
AC
AC
AQ
0.0033 AC250V Ceramic
AC
2200p 1.6kV M-Poly.
AE
470p 50V
Ceramic
AA
100
35V
EL.
AC
1000p 50V
Mylar
AA
4700p 500V Ceramic
AB
4700p 500V Ceramic
AB
0.1
50V
Mylar
AB
100
160V EL.
AG
220
160V EL.
AL
560p 2kV
Ceramic
AD
560p 2kV
Ceramic
AD
10
16V
EL.
AB
1000 16V
EL.
AE
1000 16V
EL.
AE
1000p 500V Ceramic
AA
1000p 500V Ceramic
AA
1000p 500V Ceramic
AA
100
16V
EL.
AC
47
16V
EL.
AB
470
35V
EL.
AB
0.022 50V
Mylar
AB
0.47
50V
EL.
AB
11p
50V
Ceramic
AA
0.1
16V
Ceramic
AB
0.1
16V
Ceramic
AB
0.1
16V
Ceramic
AB
220p 50V
Ceramic
AA
1000p 50V
Ceramic
AA
(CN27S10)
3.3
50V
EL.
AB
(27N-S180, CN27S10/14/18)
47
16V
EL.
AB
(27N-S180, CN27S10/14/18)
3.3
50V
EL.
AB
(27N-S180, CN27S10/14/18)
2.2
50V
EL.
AB
2.2
50V
EL.
AB
680p 50V
Ceramic
AA
(27N-S180, CN27S10/14/18)
680p 50V
Ceramic
AA
(27N-S180, CN27S10/14/18)
3.3
50V
EL.
AB
(27N-S180, CN27S10/14/18)
3.3
50V
EL.
AB
(27N-S180, CN27S10/14/18)
0.018 25V
Ceramic
AA
(27N-S180, CN27S10/14/18)
0.018 25V
Ceramic
AA
(27N-S180, CN27S10/14/18)
10
50V
EL.
AB
10
50V
EL.
AB
0.01
50V
Ceramic
AA
10
16V
EL.
AB
10
16V
EL.
AB
(27N-S100/180, CN27S14/18)
100p 50V
Ceramic
AA
100p 50V
Ceramic
AA
100
10V
EL.
AB
1
50V
EL.
AB
0.1
16V
Ceramic
AB
100p 50V
Ceramic
AA
100
10V
EL.
AB
1500p 50V
Ceramic
AA
39p
50V
Ceramic
AA
4.7
50V
EL.
AB
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
RJ61
MAIN UNIT (Continued)
C2602
C3001
C3002
C3003
C3004
C3005
C3006
C3007
C3008
C3009
C3010
C3011
C3012
C3013
C3014
C3015
C3016
C3017
C3018
C3019
C3020
C3021
C3022
VCCCCY1HH101J
VCE9GA1HW475M
VCKYCY1HB562K
VCQYTA1HM123K
VCEA0A1HW105M
VCEA0A1HW475M
VCEA0A1HW106M
VCEA0A1HW475M
VCKYCY1HF103Z
VCEA0A1CW227M
VCE9GA1HW475M
VCEA0A1HW475M
VCE9GA1HW475M
VCKYCY1HB272K
VCQYTA1HM473K
VCSATA1CE335K
VCE9GA1HW475M
VCSATA1CE106K
VCEA0A1HW105M
VCEA0A1HW475M
VCEA0A1HW475M
VCEA0A1HW475M
VCEA0A1HW475M
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
100p
4.7
5600p
0.012
1
4.7
10
4.7
0.01
220
4.7
4.7
4.7
2700p
0.047
3.3
4.7
10
1
4.7
4.7
4.7
4.7
50V
50V
50V
50V
50V
50V
50V
50V
50V
16V
50V
50V
50V
50V
50V
16V
50V
16V
50V
50V
50V
50V
50V
Ceramic
EL.(N.P)
Ceramic
Mylar
EL.
EL.
EL.
EL.
Ceramic
EL.
EL.(N.P)
EL.
EL.(N.P)
Ceramic
Mylar
Tantalum
EL.(N.P)
Tantalum
EL.
EL.
EL.
EL.
EL.
å
å
å
AA
AB
AA
AA
AB
AB
AB
AB
AA
AC
AB
AB
AB
AA
AB
AC
AB
AD
AB
AB
AB
AB
AB
R251
R252
R253
R254
RESISTORS
RJ1
RJ10
RJ11
RJ12
RJ13
RJ14
RJ15
RJ17
RJ19
RJ20
RJ21
RJ22
RJ25
RJ26
RJ28
RJ29
RJ30
RJ31
RJ32
RJ33
RJ35
RJ36
RJ37
RJ38
RJ39
RJ40
RJ41
RJ42
RJ43
RJ46
RJ48
RJ49
RJ50
RJ51
RJ52
RJ54
RJ55
RJ56
RJ57
RJ58
RJ59
RJ60
RJ63
RJ64
RJ67
R51
R52
R53
R54
R55
R56
R57
R201
R202
R203
R204
R205
R206
R207
R208
R209
R255
[M-Ox.··· Metal Oxide, M-Film··· Metal Film]
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
(CN27S10)
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
VRD-MN2BE000J J 0
1/8W
Carbon
AA
R256
R257
R258
R259
R301
R302
R303
R304
R305
R306
R351
R352
R353
R354
R355
R356
R357
R358
R401
R402
R403
R404
R405
R406
R407
R408
R409
R410
R411
R412
R413
R414
R415
R416
R421
R422
45
Part No.
VRS-CY1JF000J
★
Description
Code
J 0
1/16W
M-Ox.
AA
(27N-S100, CN27S10/14)
VRD-MN2BE000J
0
1/8W
Carbon
AA
VRD-MN2BE000J J 0
1/8W
Carbon
AA
VRS-CY1JF000J
J 0
1/16W
M-Ox.
AA
VRS-RG3AB151J M 150 1W
M-Ox.
AA
VRS-RG3DB123J J 12k 2W
M-Ox.
AA
VRS-RG3AB470J J 47 1W
M-Ox.
AA
VRD-MN2BE101J J 100 1/8W
Carbon
AA
VRD-MN2BE101J J 100 1/8W
Carbon
AA
VRD-MN2BE823J J 82k 1/8W
Carbon
AA
VRD-MN2BE392J J 3.9k 1/8W
Carbon
AA
VRD-MN2BE151J J 150 1/8W
Carbon
AA
VRD-MN2BE122J J 1.2k 1/8W
Carbon
AA
VRD-MN2BE682J J 6.8k 1/8W
Carbon
AA
VRD-MN2BE270J J 27 1/8W
Carbon
AA
VRS-CY1JF331J
J 330 1/16W
M-Ox.
AA
VRD-MN2BE121J J 120 1/8W
Carbon
AA
VRD-MN2BE4R7J J 4.7 1/8W
Carbon
AA
VRD-MN2BE331J J 330 1/8W
Carbon
AA
VRS-CY1JF222J
J 2.2k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRS-CY1JF332J
J 3.3k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRD-MN2BE562J J 5.6k 1/8W
Carbon
AA
(27N-S180, CN27S18)
VRD-MN2BE332J J 3.3k 1/8W
Carbon
AA
(27N-S180, CN27S18)
VRD-MN2BE223J J 22k 1/8W
Carbon
AA
(27N-S180, CN27S18)
VRS-CY1JF563J
J 56k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRS-CY1JF182J
J 1.8k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRS-CY1JF470J
J 47 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRS-CY1JF472J
J 4.7k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRS-CY1JF472J
J 4.7k 1/16W
M-Ox.
AA
(27N-S180, CN27S18)
VRD-MN2BE222J J 2.2k 1/8W
Carbon
AA
VRS-CY1JF102J
J 1k 1/16W
M-Ox.
AA
VRD-MN2BE103J J 10k 1/8W
Carbon
AA
VRD-MN2BE333J J 33k 1/8W
Carbon
AA
VRD-MN2BE102J J 1k 1/8W
Carbon
AA
VRD-MN2BE152J J 1.5k 1/8W
Carbon
AA
VRD-MN2BE683J J 68k 1/8W
Carbon
AA
VRD-MN2BE103J J 10k 1/8W
Carbon
AA
VRD-RA2BE822J J 8.2k 1/8W
Carbon
AA
VRD-MN2BE223J J 22k 1/8W
Carbon
AA
VRD-MN2BE683J J 68k 1/8W
Carbon
AA
VRD-MN2BE103J J 10k 1/8W
Carbon
AA
VRD-MN2BE822J J 8.2k 1/8W
Carbon
AA
VRD-MN2BE223J J 22k 1/8W
Carbon
AA
VRS-CY1JF682J
J 6.8k 1/16W
M-Ox.
AA
VRS-CY1JF331J
J 330 1/16W
M-Ox.
AA
VRS-CY1JF391J
J 390 1/16W
M-Ox.
AA
VRD-MN2BE102J J 1k 1/8W
Carbon
AA
VRS-CY1JF470J
J 47 1/16W
M-Ox.
AA
VRS-CY1JF680J
J 68 1/16W
M-Ox.
AA
VRS-CY1JF102J
J 1k 1/16W
M-Ox.
AA
VRS-CY1JF471J
J 470 1/16W
M-Ox.
AA
VRD-MN2BE562J J 5.6k 1/8W
Carbon
AA
VRD-RA2BE154J J 150k 1/8W
Carbon
AA
VRD-MN2BE153J J 15k 1/8W
Carbon
AA
VRD-RA2BE561J J 560 1/8W
Carbon
AA
VRS-CY1JF101J
J 100 1/16W
M-Ox.
AA
VRS-CY1JF101J
J 100 1/16W
M-Ox.
AA
VRS-CY1JF101J
J 100 1/16W
M-Ox.
AA
VRS-CY1JF332J
J 3.3k 1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
VRD-MN2BE152J J 1.5k 1/8W
Carbon
AA
(CN27S10)
VRS-CY1JF472J
J 4.7k 1/16W
M-Ox.
AA
(CN27S10)
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
MAIN UNIT (Continued)
R423
VRS-CY1JF152J
R424
VRS-CY1JF102J
R451
R452
R453
R454
R456
R458
å R501
R510
R511
R512
R513
R514
R519
R520
R523
R524
R526
R551
R552
R553
R554
å R604
R605
R606
å R607
å R609
R610
å R611
å R621
å R622
å R623
å R624
R625
R627
R631
R632
R633
R634
çå R651
çå R652
çå R653
çå R654
çå R655
R690
å R701
å R702
R704
å R705
å R706
R707
å R709
R710
R711
å R715
å R723
R724
R725
R726
R727
å R728
R734
å R737
R751
R801
R802
R803
å
VRS-RG2HC103J
VRD-RM2HD153J
VRD-RA2EE683J
VRD-MN2BE102J
VRD-MN2BE682J
VRD-MN2BE152J
VRN-RL3ABR56J
VRD-MN2BE471J
VRD-RA2BE823G
VRD-RA2BE124G
VRD-RA2BE473J
VRD-MN2BE101J
VRD-RA2BE153G
VRD-MN2BE184J
VRN-RL3AB1R0J
VRS-RG3AB391J
VRD-MN2BE562J
VRS-CY1JF472J
VRS-CY1JF102J
VRD-MN2BE333J
VRD-MN2BE333J
VRS-RG3LB392J
VRD-RA2BE331J
VRD-RA2BE331J
VRS-RG3LB392J
VRS-RG3AB562J
VRD-RM2HD220J
VRS-KA3NG3R3K
VRN-RL3DB1R2J
VRN-RL3ABR39J
VRN-RL3AB2R7J
VRS-RG3DB332J
VRD-MN2BE102J
VRD-RM2HD224J
VRS-CY1JF391J
VRS-CY1JF152J
VRD-MN2BE472J
VRD-RA2BE4R7J
VRS-RG2HC270J
VRN-RA2BK103F
VRN-RA2BK822F
VRD-MN2BE184J
VRS-CY1JF104J
VRS-RG2HC102J
RR-HZ0048CEZZ
VRW-KQ3NC1R2K
VRD-RM2HD154J
VRN-RL3DBR22J
VRN-RL3DBR27J
VRS-RG2HC681J
VRN-GA2EB1R0J
VRD-RM2HD470J
VRD-RA2BE242J
VRS-RG3DB153J
VRN-RL3DBR39J
VRS-RG2HC332J
VRS-RG2HC821J
VRS-RG2HC122J
VRD-RA2BE271J
VRN-RL3LB4R7J
VRD-RM2HD124J
VRN-RL3DBR56J
VRD-MN2BE473J
VRD-MN2BE332J
VRS-CY1JF332J
VRS-CY1JF222J
J 1.5k 1/16W
(CN27S10)
J 1k 1/16W
(CN27S10)
J 10k 1/2W
J 15k 1/2W
J 68k 1/4W
J 1k 1/8W
J 6.8k 1/8W
J 1.5k 1/8W
J 0.56 1W
J 470 1/8W
J 82k 1/8W
J 120k 1/8W
J 47k 1/8W
J 100 1/8W
J 15k 1/8W
J 180k 1/8W
M 1
1W
J 390 1W
J 5.6k 1/8W
J 4.7k 1/16W
J 1k 1/16W
J 33k 1/8W
J 33k 1/8W
M 3.9k 3W
J 330 1/8W
J 330 1/8W
M 3.9k 3W
M 5.6k 1W
J 22 1/2W
J 3.3 7W
M 1.2 2W
M 0.39 1W
M 2.7 1W
M 3.3k 2W
J 1k 1/8W
J 220k 1/2W
J 390 1/16W
J 1.5k 1/16W
J 4.7k 1/8W
J 4.7 1/8W
M 27 1/2W
J 10k 1/8W
J 8.2k 1/8W
J 180k 1/8W
J 100k 1/16W
J 1k 1/2W
J 3.9M 1/2W
J 1.2 7W
J 150k 1/2W
J 0.22 2W
M 0.27 2W
J 680 1/2W
J 1
1/4W
J 47 1/2W
J 2.4k 1/8W
J 15k 2W
M 0.39 2W
J 3.3k 1/2W
M 820 1/2W
M 1.2k 1/2W
J 270 1/8W
M 4.7 3W
J 120k 1/2W
M 0.56 2W
J 47k 1/8W
J 3.3k 1/8W
J 3.3k 1/16W
J 2.2k 1/16W
Part No.
★
R804
R805
R806
R807
VRS-CY1JF222J
VRS-CY1JF222J
VRS-CY1JF333J
VRS-CY1JF152J
J
J
J
J
Ref. No.
M-Ox.
AA
R808
VRD-RA2BE102J
J
M-Ox.
AA
R901
VRD-RA2BE331J
J
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Film
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Film
M-Ox.
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
M-Ox.
M-Film
M-Film
M-Film
M-Ox.
Carbon
Carbon
M-Ox.
M-Ox.
Carbon
Carbon
M-Ox.
M-Film
M-Film
Carbon
M-Ox.
M-Ox.
Solid
Cement
Carbon
M-Film
M-Film
M-Ox.
M-Film
Carbon
Carbon
M-Ox.
M-Film
M-Ox.
M-Ox.
M-Ox.
Carbon
M-Film
Carbon
M-Film
Carbon
Carbon
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AB
AA
AA
AD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AE
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
R903
VRD-MN2BE102J
J
R904
VRS-CY1JF683J
J
R905
VRS-CY1JF223J
J
R906
VRS-CY1JF392J
J
R907
VRS-CY1JF182J
J
R908
VRS-CY1JF102J
J
R910
VRS-CY1JF102J
J
R911
VRS-CY1JF683J
J
R912
VRS-CY1JF223J
J
R913
VRS-CY1JF392J
J
R914
VRS-CY1JF182J
J
R915
VRS-CY1JF102J
J
R922
VRS-CY1JF102J
J
R923
VRS-CY1JF102J
J
R924
R925
R926
R931
VRS-CY1JF750J
VRD-MN2BE104J
VRD-MN2BE104J
VRS-CY1JF750J
J
J
J
J
R932
VRS-CY1JF750J
J
R951
R952
R953
VRD-RA2BE101J
VRD-MN2BE102J
VRS-CY1JF101J
J
J
J
R961
R962
R2001
R2002
R2004
R2006
R2008
R2009
R2010
R2012
R2016
R2020
R2023
R2024
R2025
R2026
R2027
R2028
R2029
VRD-RA2BE101J
VRD-RA2BE101J
VRD-RA2BE562J
VRD-MN2BE103J
VRD-MN2BE101J
VRS-CY1JF103J
VRD-MN2BE333J
VRD-RA2BE102J
VRD-MN2BE102J
VRS-CY1JF471J
VRS-CY1JF223J
VRS-CY1JF223J
VRS-CY1JF223J
VRD-RA2BE682J
VRD-RA2BE682J
VRD-RA2BE682J
VRD-MN2BE682J
VRD-MN2BE102J
VRS-CY1JF103J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
R2032 VRD-RA2BE103J
R2034 VRD-RA2BE102J
J
J
R2035 VRD-MN2BE223J
R2038 VRD-RA2BE103J
J
J
R2040 VRD-MN2BE102J
J
46
Description
Code
2.2k 1/16W
M-Ox.
AA
2.2k 1/16W
M-Ox.
AA
33k 1/16W
M-Ox.
AA
1.5k 1/16W
M-Ox.
AA
(CN27S10)
1k 1/8W
Carbon
AA
(CN27S10)
330 1/8W
Carbon
AA
(27N-S180, CN27S10/14/18)
1k 1/8W
Carbon
AA
(27N-S180, CN27S10/14/18)
68k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
22k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
3.9k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1.8k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
68k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
22k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
3.9k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1.8k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
1k 1/16W
M-Ox.
AA
(27N-S180, CN27S10/14/18)
75 1/16W
M-Ox.
AA
100k 1/8W
Carbon
AA
100k 1/8W
Carbon
AA
75 1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
75 1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
100 1/8W
Carbon
AB
1k 1/8W
Carbon
AA
100 1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
100 1/8W
Carbon
AB
100 1/8W
Carbon
AB
5.6k 1/8W
Carbon
AA
10k 1/8W
Carbon
AA
100 1/8W
Carbon
AA
10k 1/16W
M-Ox.
AA
33k 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
470 1/16W
M-Ox.
AA
22k 1/16W
M-Ox.
AA
22k 1/16W
M-Ox.
AA
22k 1/16W
M-Ox.
AA
6.8k 1/8W
Carbon
AA
6.8k 1/8W
Carbon
AA
6.8k 1/8W
Carbon
AA
6.8k 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
10k 1/16W
M-Ox.
AA
(27N-S100, CN27S10/14)
10k 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
(27N-S180, CN27S18)
22k 1/8W
Carbon
AA
10k 1/8W
Carbon
AA
(27N-S180, CN27S18)
1k 1/8W
Carbon
AA
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-A: DUNTKA126WEK4/K8 (27N-S100/CN27S10)
PWB-A: DUNTKA126WEK5 (27N-S180, CN27S18)
PWB-A: DUNTKA126WEL6 (CN27S14)
VRD-MN2BE333J
VRD-MN2BE101J
VRS-CY1JF333J
VRD-MN2BE682J
VRD-MN2BE101J
VRD-RA2BE101J
VRS-CY1JF221J
VRS-CY1JF562J
VRD-MN2BE221J
VRD-MN2BE562J
VRD-MN2BE183J
VRD-MN2BE222J
VRD-RA2BE332J
VRS-CY1JF103J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
R2068 VRS-CY1JF103J
R2069 VRS-CY1JF102J
J
J
R2070
R2071
R2101
R2102
R2201
R2202
R2203
R2211
R2212
R2213
R2401
R2402
R2403
R2404
R2501
R2503
R2504
R2505
R2506
R2507
R2508
R2509
R2601
R3001
R3002
R3003
R3004
R3005
R3007
R3008
R3010
R3011
R3012
R3013
R3014
R3015
R3016
R3017
R3018
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
VRS-CY1JF103J
VRD-RA2BE102J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-MN2BE222J
VRS-CY1JF103J
VRS-CY1JF184J
VRD-MN2BE222J
VRS-CY1JF682J
VRS-CY1JF333J
VRS-CY1JF101J
VRS-CY1JF101J
VRD-MN2BE101J
VRD-MN2BE101J
VRD-MN2BE103J
VRD-MN2BE273J
VRD-MN2BE123J
VRD-MN2BE563J
VRD-MN2BE563J
VRD-MN2BE823J
VRD-MN2BE153J
VRD-MN2BE272J
VRD-RA2BE331J
VRD-RA2BE101J
VRD-RA2BE101J
VRS-CY1JF105J
VRS-CY1JF104J
VRS-CY1JF623J
VRS-CY1JF332J
VRS-CY1JF302J
VRS-CY1JF392J
VRD-MN2BE102J
VRS-CY1JF102J
VRD-MN2BE104J
VRD-MN2BE104J
VRD-RA2BE101J
VRD-MN2BE750J
VRD-RA2BE102J
VRD-RA2BE102J
J Power
AB
J Vol-Down
AB
J Vol-Up
AB
J CH-Down
AB
Description
Code
AB
MISCELLANEOUS PARTS
33k 1/8W
Carbon
AA
100 1/8W
Carbon
AA
33k 1/16W
M-Ox.
AA
6.8k 1/8W
Carbon
AA
100 1/8W
Carbon
AA
100 1/8W
Carbon
AB
220 1/16W
M-Ox.
AA
5.6k 1/16W
M-Ox.
AA
220 1/8W
Carbon
AA
5.6k 1/8W
Carbon
AA
18k 1/8W
Carbon
AA
2.2k 1/8W
Carbon
AA
3.3k 1/8W
Carbon
AA
10k 1/16W
M-Ox.
AA
(CN27S10)
10k 1/16W
M-Ox.
AA
1k 1/16W
M-Ox.
AA
(27N-S100/180, CN27S14/18)
10k 1/16W
M-Ox.
AA
1k 1/8W
Carbon
AA
100 1/16W
M-Ox.
AA
100 1/16W
M-Ox.
AA
2.2k 1/8W
Carbon
AA
10k 1/16W
M-Ox.
AA
180k 1/16W
M-Ox.
AA
2.2k 1/8W
Carbon
AA
6.8k 1/16W
M-Ox.
AA
33k 1/16W
M-Ox.
AA
100 1/16W
M-Ox.
AA
100 1/16W
M-Ox.
AA
100 1/8W
Carbon
AA
100 1/8W
Carbon
AA
10k 1/8W
Carbon
AA
27k 1/8W
Carbon
AA
12k 1/8W
Carbon
AA
56k 1/8W
Carbon
AA
56k 1/8W
Carbon
AA
82k 1/8W
Carbon
AA
15k 1/8W
Carbon
AA
2.7k 1/8W
Carbon
AA
330 1/8W
Carbon
AA
100 1/8W
Carbon
AB
100 1/8W
Carbon
AB
1M 1/16W
M-Ox.
AA
100k 1/16W
M-Ox.
AA
62k 1/16W
M-Ox.
AA
3.3k 1/16W
M-Ox.
AA
3k 1/16W
M-Ox.
AA
3.9k 1/16W
M-Ox.
AA
1k 1/8W
Carbon
AA
1k 1/16W
M-Ox.
AA
100k 1/8W
Carbon
AA
100k 1/8W
Carbon
AA
100 1/8W
Carbon
AB
75 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
1k 1/8W
Carbon
AA
RY701 RRLYJ0081CEZZ
or
RRLYJ0088CEZZ
or
RRLYJ0094CEZZ
å F701
QFS-B4023CEZZ
or
QFS-B4021GEZZ
FB601 RBLN-0047CEZZ
FB702 RBLN-0036CEZZ
FB704 RBLN-0037CEZZ
FB706 RBLN-0037CEZZ
FH701 QFSHD1013CEZZ
FH702 QFSHD1014CEZZ
J931 QSOCD0430CEZZ
å
P351
P601
P621
P651
P701
P703
P901
P903
P931
QPLGN0461CEZZ
QPLGN0160FJZZ
QPLGN0461CEZZ
QPLGN0361CEZZ
QPLGN0207CEZZ
QPLGN0269GEZZ
QPLGN0561CEZZ
QPLGN0561CEZZ
QPLGN0661CEZZ
J Relay
AL
J Fuse, 4A 125V
AC
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
P2401 QPLGN0561CEZZ J
SC401 QSOCN0585CEZZ
SC402 QSOCN0585CEZZ
RMC2601 RRMCU0235CEZZ J
RDA501
RDA604
RDA701
RDA751
TAN921
TAN921
PRDAR0234PEFW R
PRDAR0233PEFW R
PRDAR1008MEFW M
PRDAR5072CEFW J
QTANJ0323CEZZ J
QTANJ0523CEZZ M
LX-BZ3049GEFD
LX-HZ3007MEFD
SWITCHES
S2501 QSW-K0079GEZZ
or
QSW-K0202PEZZ
S2502 QSW-K0079GEZZ
or
QSW-K0202PEZZ
S2503 QSW-K0079GEZZ
or
QSW-K0202PEZZ
S2504 QSW-K0079GEZZ
or
★
QSW-K0202PEZZ
S2505 QSW-K0079GEZZ J CH-Up
or
QSW-K0202PEZZ
MAIN UNIT (Continued)
R2041
R2042
R2043
R2044
R2045
R2046
R2047
R2048
R2060
R2061
R2062
R2063
R2064
R2067
Part No.
47
J
M
Ferrite Bead
AB
Ferrite Bead
AB
Ferrite Bead
AB
Ferrite Bead
AB
Fuse Holder
AC
Fuse Holder
AC
Socket, S-Video
AE
(27N-S100/180, CN27S14/18)
Plug, 4-pin (S)
AB
Plug, 5-pin (K)
AD
Plug, 4-pin (YBN)
AB
Plug, 3-pin
AB
Plug, 2-pin (M)
AA
Plug, 2-pin (P)
AB
Plug, 5-pin (HA)
AB
Plug, 5-pin (GBN)
AB
Plug, 6-pin (KC)
AD
(27N-S100/180, CN27S14/18)
Plug, 5-pin
AB
Socket, 5-pin (KA)
AC
(27N-S100/180, CN27S14/18)
Socket, 5-pin (KB)
AC
(27N-S100/180, CN27S14/18)
R/C Receiver
AK
Heat Sink, for IC501
AH
Heat Sink, for Q602
AK
Heat Sink, for IC701
AH
Heat Sink, for IC751
AC
AV Terminal (27N-S100)
AL
AV Terminal
AG
(27N-S180, CN27S10/14/18)
Screw
AA
Screw
AA
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
★
Part No.
Description
Code
Ref. No.
CRT UNIT
TRANSISTORS
Q853
Q854
Q855
Q856
Q881
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB1E
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB1E
VS2SC3198-Y-1
VS2SC3789//2E
or
VS2SC3619LB1E
VS2SA1266-Y-1
AA
AA
IC1501 VHiM52055FP-1
J 2SC3198(Y)
M 2SC3789
AA
AA
J 2SC3198(Y)
M 2SC3789
AA
AA
J 2SA1266(Y)
AA
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D1501 VHD1SS119//-1
J Diode
AB
D1502 VHD1SS119//-1
J Diode
AB
D1503 RH-EX0631GEZZ J Zener Diode, 9V
AA
D1504 RH-EX0631GEZZ J Zener Diode, 9V
AA
COILS
L1501 VP-XF6R8K0000
L1502 VP-XF6R8K0000
L1503 VP-XF8R2K0000
J Peaking 82µH
AB
CAPACITORS
C883
[EL.··· Electrolytic]
VCCSPA1HL391J J 390p 50V
VCCSPA1HL331J J 330p 50V
VCCSPA1HL391J J 390p 50V
RC-KZ0024CEZZ J 0.001 2kV
or
VCKYPB3DE472Z
0.0047 2kV
VCEA0A1HW106M J 10
50V
R851
R852
R853
R855
R856
R857
R858
R859
R860
R861
R863
R864
R865
R866
R867
R868
R869
R871
R872
R873
R874
R881
R882
R883
R884
R895
[M-Ox.··· Metal Oxide]
VRD-RA2BE470J J 47
1/8W
VRD-RA2BE181J J 180
1/8W
VRD-RA2BE121J J 120
1/8W
VRD-RA2BE471J J 470
1/8W
VRD-RA2BE221J J 220
1/8W
VRS-VV3LB123J
J 12k
3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE470J J 47
1/8W
VRD-RA2BE181J J 180
1/8W
VRD-RA2BE121J J 120
1/8W
VRD-RA2BE471J J 470
1/8W
VRD-RA2BE221J J 220
1/8W
VRS-VV3LB123J
J 12k
3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE470J J 47
1/8W
VRD-RA2BE181J J 180
1/8W
VRD-RA2BE121J J 120
1/8W
VRD-RA2BE471J J 470
1/8W
VRD-RA2BE221J J 220
1/8W
VRS-VV3LB123J
J 12k
3W
VRD-RM2HD222J J 2.2k 1/2W
VRD-RA2BE102J J 1k
1/8W
VRD-RA2BE331J J 330
1/8W
VRD-RA2BE561J J 560
1/8W
VRD-RA2BE152J J 1.5k 1/8W
VRD-RA2BE470J J 47
1/8W
å
å
J Peaking 6.8µH
J Peaking 6.8µH
J Peaking 8.2µH
AB
AB
AB
CAPACITORS
Ceramic
Ceramic
Ceramic
Ceramic
AA
AA
AA
AC
Ceramic
EL.
AB
RESISTORS
å
AH
TRANSISTORS
COIL
C851
C852
C853
C854
J M52055FP
You can substitute "VS2SD601AR/-1" for "VS2SC2412KQ-1".
Q1501 VS2SC2412KQ-1 J 2SC2412K
AA
Q1502 VS2SB709AR/-1
J 2SB709AR
AC
or
VS2SA1037KR-1
Q1503 VS2SC2412KQ-1 J 2SC2412K
AA
Q1504 VS2SC2412KQ-1 J 2SC2412K
AA
DIODES
VP-MK820K0000
Code
INTEGRATED CIRCUIT
J 2SC3198(Y)
M 2SC3789
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D881 VHD1SS119//-1
J Diode
AB
D882 VHD1SS119//-1
J Diode
AB
D884 VHD1SS119//-1
J Diode
AB
L851
Description
PWB-K: DUNTKA114WEK0 (27N-S100, CN27S14)
S-VIDEO UNIT
PWB-B: DUNTK9510WEK1
Q851
Q852
★
Part No.
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
M-Ox.
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
AB
AA
AA
AA
AA
AA
AA
[EL.··· Electrolytic]
VCEA0A1CW106M J 10
16V
VCCCCY1HH470J J 47p
50V
VCKYCY1HF103Z J 0.01 50V
VCCCCY1HH271J J 270p 50V
VCCCCY1HH330J J 33p
50V
VCCCCY1HH151J J 150p 50V
VCCCCY1HH330J J 33p
50V
VCE9GA1CW106M J 10
16V
VCEA0A1CW106M J 10
16V
VCKYCY1HF103Z J 0.01 50V
VCEA0A1CW106M J 10
16V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
R1501
R1502
R1503
R1504
R1505
R1506
R1507
R1508
R1509
R1510
R1511
R1512
R1513
R1514
R1515
R1516
R1517
R1518
R1519
[M-Ox.··· Metal Oxide]
VRS-CY1JF223J
J 22k 1/16W
VRS-CY1JF123J
J 12k 1/16W
VRS-CY1JF122J
J 1.2k 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF152J
J 1.5k 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF561J
J 560 1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF181J
J 180 1/16W
VRS-CY1JF152J
J 1.5k 1/16W
VRS-CY1JF333J
J 33k 1/16W
VRS-CY1JF122J
J 1.2k 1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF102J
J 1k 1/16W
VRS-CY1JF682J
J 6.8k 1/16W
VRS-CY1JF103J
J 10k 1/16W
VRS-CY1JF101J
J 100 1/16W
VRS-CY1JF101J
J 100 1/16W
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL. (N.P)
EL.
Ceramic
EL.
Ceramic
Ceramic
AB
AA
AA
AA
AA
AA
AA
AB
AB
AA
AB
AA
AA
RESISTORS
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
MISCELLANEOUS PARTS
P851 QPLGN0541CEZZ J Plug, 5-pin (GBN)
P852 QPLGN0441CEZZ J Plug, 4-pin (YBN)
SC851 QSOCV0937CEZZ M CRT Socket
C1501
C1502
C1503
C1504
C1505
C1506
C1507
C1508
C1509
C1510
C1511
C1512
C1513
P1501 QPLGN0585CEZZ J Plug, 5-pin (KA)
P1502 QPLGN0585CEZZ J Plug, 5-pin (KB)
P1503 QPLGN0661CEZZ J Plug, 6-pin (KC)
AB
AB
AF
48
AB
AD
AD
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
★
Part No.
Description
Code
Ref. No.
PWB-K: DUNTKA115WEK0 (27N-S180, CN27S18)
DIGICOM/S-VIDEO UNIT
R1404
R1405
R1406
R1407
R1408
R1409
R1410
R1411
R1412
R1413
R1414
R1415
R1416
R1417
R1418
R1419
R1420
R1421
R1422
R1425
R1451
R1452
R1453
R1454
R1455
INTEGRATED CIRCUIT
IC1401 VHiTC90A45F-1
IC1403 VHiKA78L05B-1
IC1451 VHiM52055FP-1
J TC90A45F
J KIA78L05BP
J M52055FP
AM
AE
AH
TRANSISTORS
You can substitute "VS2SD601AR/-1" for "VS2SC2412KQ-1".
Q1401 VS2SC2412KQ-1 J 2SC2412K
AA
Q1402 VS2SC2412KQ-1 J 2SC2412K
AA
Q1403 VS2SC2412KQ-1 J 2SC2412K
AA
Q1404 VS2SC2412KQ-1 J 2SC2412K
AA
Q1405 VS2SC2412KQ-1 J 2SC2412K
AA
Q1406 VS2SC2412KQ-1 J 2SC2412K
AA
Q1407 VS2SC2412KQ-1 J 2SC2412K
AA
DIODES
You can substitute "RH-DX0475CEZZ" for "VHD1SS119//-1".
D1401 VHD1SS119//-1
J Diode
AB
D1402 VHD1SS119//-1
J Diode
AB
D1403 VHD1SS119//-1
J Diode
AB
D1451 VHD1SS119//-1
J Diode
AB
D1452 VHD1SS119//-1
J Diode
AB
D1453 RH-EX0631GEZZ J Zener Diode, 9V
AA
D1454 RH-EX0631GEZZ J Zener Diode, 9V
AA
VP-XF100K0000
VP-XF100K0000
VP-XF150K0000
VP-XF330K0000
VP-XF100K0000
J
J
J
J
J
Coil
Coil
Coil
Coil
Coil
10µH
10µH
15µH
33µH
10µH
[EL.··· Electrolytic]
VCCCCY1HH220J J 22p
50V
VCFYSA1HB474J J 0.47 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1CB104K J 0.1
16V
VCEA0A1HW106M J 10
50V
VCKYCY1HF103Z J 0.01 50V
VCCCCY1HH181J J 180p 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HF103Z J 0.01 50V
VCEA0A1CW476M J 47
16V
VCKYCY1CB104K J 0.1
16V
VCCCCY1HH390J J 39p
50V
VCEA0A1HW106M J 10
50V
VCEA0A1HW106M J 10
50V
VCKYCY1HB103K J 0.01 50V
VCCCCY1HH120J J 12p
50V
VCCCCY1HH120J J 12p
50V
VCKYCY1CB104K J 0.1
16V
VCKYCY1CB104K J 0.1
16V
VCKYCY1HB102K J 1000p 50V
VCE9GA1CW106M J 10
16V
VCCCCY1HH270J J 27p
50V
VCKYCY1HF103Z J 0.01 50V
VCEA0A1CW106M J 10
16V
VCKYCY1HF103Z J 0.01 50V
VCKYCY1HB103K J 0.01 50V
VCE9GA1CW106M J 10
16V
AB
AB
AB
AB
AB
Ceramic
Mylar
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL.
Ceramic
Ceramic
EL.
EL.
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
EL. (N.P)
Ceramic
Ceramic
EL.
Ceramic
Ceramic
EL. (N.P)
AA
AC
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AA
AB
AB
AA
AB
AB
AA
AA
AA
AB
AB
AA
AB
AA
AA
AB
AA
AA
AB
RESISTORS
[M-Ox.··· Metal Oxide]
R1401 VRS-CY1JF103J
J 10k 1/16W M-Ox.
R1402 VRS-CY1JF103J
J 10k 1/16W M-Ox.
R1403 VRS-CY1JF182J
J 1.8k 1/16W M-Ox.
VRS-CY1JF102J
VRS-CY1JF392J
VRS-CY1JF102J
VRS-CY1JF103J
VRS-CY1JF821J
VRS-CY1JF101J
VRS-CY1JF681J
VRS-CY1JF101J
VRS-CY1JF821J
VRS-CY1JF471J
VRS-CY1JF102J
VRS-CY1JF821J
VRS-CY1JF122J
VRS-CY1JF273J
VRS-CY1JF153J
VRS-CY1JF101J
VRS-CY1JF222J
VRS-CY1JF562J
VRS-CY1JF101J
VRS-CY1JF471J
VRS-CY1JF101J
VRS-CY1JF101J
VRS-CY1JF682J
VRS-CY1JF102J
VRS-CY1JF103J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
J
Description
1k
3.9k
1k
10k
820
100
680
100
820
470
1k
820
1.2k
27k
15k
100
2.2k
5.6k
100
470
100
100
6.8k
1k
10k
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
1/16W
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
M-Ox.
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
MISCELLANEOUS PARTS
CAPACITORS
C1401
C1402
C1403
C1404
C1405
C1406
C1407
C1408
C1409
C1410
C1411
C1412
C1413
C1415
C1416
C1417
C1418
C1419
C1420
C1421
C1423
C1424
C1425
C1426
C1427
C1428
C1451
C1452
C1453
C1454
C1455
★
P1401 QPLGN0585CEZZ J Plug, 5-pin (KA)
P1402 QPLGN0585CEZZ J Plug, 5-pin (KB)
P1451 QPLGN0661CEZZ J Plug, 6-pin (KC)
COILS
L1401
L1402
L1403
L1405
L1406
Part No.
AA
AA
AA
49
AA
AA
AA
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
Ref. No.
Description
Code
PWB-H: DUNTK9310WEK1
PACKING PARTS
FRONT AV UNIT
(NOT REPLACEMENT ITEM)
MISCELLANEOUS PARTS
J1001
J1002
J1003
P1001
QJAKE0053GEZZ
QJAKE0055GEZZ
QJAKE0059GEZZ
QPLGN0541CEZZ
J
J
J
J
Jack, Video in
Jack, Audio in (L)
Jack, Audio in (R)
Plug, 5-pin (HA)
SPAKC0658MEZZ
SPAKC0662MEZZ
SPAKX0165MEZZ
SSAKA0004MEZZ
SPAKP0032MEZZ
AD
AD
AC
AB
ACC701 QACCD3065CESA
QCNW-0130MEZZ
QCNW-0134MEZZ
QCNW-0166MEZZ
QCNW-0167MEZZ
QCNW-0252MEZZ
SP1
VSP0080PBL4YS
or
VSP0080PBK9YA
SP2
VSP0080PBL4YS
or
VSP0080PBK9YA
M
M
M
M
M
M
M
AC Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Connecting Cord
Speaker, (L)
M Speaker, (R)
M Operation Manual
(27N-S100/180)
TiNS-6935MEN1
M Operation Manual
(CN27S10/14/18)
RRMCG1324CESA M Infrared R/C Unit
(27N-S100, CN27S10)
RRMCG1395CESA M Infrared R/C Unit
(27N-S180, CN27S14/18)
Packing Case (27N-S100/180)
Packing Case (CN27S10/14/18)
Buffer Material
Polyethylene Bag
Polyethylene Sheet
—
—
—
—
—
27N-S100, CN27S10/14
AG
AF
AE
AD
AC
AH
AG
1
1-1
1-2
1-3
1-4
1-5
2
2
CCABA1325MES0
Not Available
GCOVA1033MEKA
HBDGB1009MESA
JBTN-1096MEKA
JBTN-1097MEKA
GCABB1157MEKA
GCABB1148MEKA
1
1-1
1-2
1-3
1-4
1-5
2
CCABA1325MES0
Not Available
GCOVA1033MEKA
HBDGB1009MESA
JBTN-1096MEKA
JBTN-1097MEKA
GCABB1158MEKA
M
–
M
M
M
M
M
M
Front Cabinet Ass'y
BF
Front Cabinet
—
Cover for R/C
AD
Badge, "SHARP"
AD
Button, Power, Vol-up/down AD
Button, Ch-up/down
AD
Rear Cabinet (27N-S100) AY
Rear Cabinet (CN27S10/14) AZ
AG
27N-S180, CN27S18
SUPPLIED ACCESORRIES
TiNS-6930MEZZ
–
–
–
–
–
CABINET PARTS
MISCELLANEOUS PARTS
å
★
Part No.
M
–
M
M
M
M
M
Front Cabinet Ass'y
BF
Front Cabinet
—
Cover for R/C
AD
Badge, "SHARP"
AD
Button, Power, Vol-up/down AD
Button, Ch-up/down
AD
Rear Cabinet
AY
CABINET PARTS LOCATION
AD
AD
1
AQ
1-1
AW
2
1-4
50
1-3
1-2
1-5
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
No.
Part No.
PACKING
OFRef.
THE
SET
★
Description
★ Polyethylene Bag
Operation Manual
Infrared R/C Unit
★ Batteries
★ Polyethylene Sheet
★ Buffer Material
FRONT
★ Packing Case
★ Serial Number Label
Use 22 staples
fix the packing case.
★ Bar Code Label
REAR
★ Number Card
MARK ★ : Not replacement items.
51
Code
27N-S100, 27N-S180
CN27S10/14/18
Ref. No.
Part No.
★
Description
Code
Ref. No.
★
Part No.
Description
Code
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
TQ0883-S
Apr. 2000 Printed in Japan
MK. KG
52