advertisement
FP72E S/FP92E S
LCD Color Monitor
User Manual
Welcome
Downloaded from ManualMonitor.com Manuals
Copyright
Copyright © 2007 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.
Disclaimer
BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ
Corporation to notify any person of such revision or changes.
Please follow these safety instructions for best performance, and long life for your monitor
Power Safety
• The AC plug isolates this equipment from the AC supply.
• The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible.
• This product should be operated from the type of power indicated on the marked label. If you are not sure of the type of power available, consult your dealer or local power company.
Care And Cleaning
• Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass cleaners.
• Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a built-in installation unless proper ventilation is provided.
• Never push objects or spill liquid of any kind into this product.
Servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as dropping or mishandling occurs, contact qualified service personnel for servicing.
2
Downloaded from ManualMonitor.com Manuals
Table of Contents
How to upgrade the monitor on an existing computer ..........................................15
How to complete the Windows Upgrade Device Driver Wizard ...........................19
Downloaded from ManualMonitor.com Manuals
Table of Contents 3
1. Getting started
When unpacking please check you have the following items. If any are missing or damaged, please contact the place of purchase for a replacement.
BenQ LCD Monitor
Quick Start Guide
CD-ROM
Power Cord
(Picture may differ from product supplied for your region)
Signal Cable: D-Sub
Signal Cable: DVI-D (optional)
4 Getting started
Downloaded from ManualMonitor.com Manuals
Audio Cable
Consider keeping the box and packaging in storage for use in the future when you may need to transport the monitor. The fitted foam packing is ideal for protecting the monitor during transport.
Downloaded from ManualMonitor.com Manuals
Getting started 5
2. Getting to know your monitor
Front view
Earphone socket
Back view
1. Audio cable socket
2. AC power input jack
3. DVI-D input socket
4. D-Sub input socket
6 Getting to know your monitor
Downloaded from ManualMonitor.com Manuals
3. How to assemble your monitor hardware
If the computer is turned on you must turn it off before continuing.
Do not plug-in or turn-on the power to the monitor until instructed to do so.
1. Attach the monitor base.
Please be careful to prevent damage to the monitor.
Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like the monitor packaging bag on the desk for padding.
Gently lay the screen face down on a flat clean padded surface.
While holding the monitor firmly against the desk, pull the monitor stand arm upwards clear of the monitor.
Orient and align the stand base socket with the end of the stand arm, then push them together until they click and lock into place.
Gently attempt to pull them back apart to check that they have properly engaged.
Carefully lift the monitor, turn it over and place it upright on its stand on a flat even surface.
You should position the monitor and angle the screen to minimize unwanted reflections from other light sources.
Downloaded from ManualMonitor.com Manuals
How to assemble your monitor hardware 7
2. Connect the PC video cable.
Do not use both DVI-D cable and D-Sub cable on the same PC. The only case in which both cables can be used is if they are connected to two different PCs with appropriate video systems.
Connect one end of the DVI-D cable to the monitor
DVI-D socket and the other end to the DVI-D port on your computer. (optional)
The DVI-D format is used for direct digital connection between source video and digital LCD monitors or projectors. The digital video signals produce a superior quality picture than analog video signals.
Connect the plug of the D-Sub cable (at the end without the ferrite filter) to the monitor D-Sub socket. Connect the other plug of the D-Sub cable (at the end with the ferrite filter) to the computer video D-Sub socket.
Tighten all finger screws to prevent the plugs from accidently falling out during use.
3. Connect the audio cable.
Connect the audio cable between the socket on the rear of the monitor and your computer audio outlet.
Either
Or
If you wish, you may connect an earphone into the earphone socket located on the side panel of the monitor.
8 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
4. Connect the power cable to the monitor.
Plug one end of the power cord into the socket labelled
‘POWER IN’ on the rear of the monitor. Do not connect the other end to a power point just yet.
5. Route the cables via the cable clip.
Release the cable retaining clip by squeezing the clip inwards as illustrated. Position the cables together and reinsert the clip over them to retain the cables neatly in place behind the monitor stand.
6. Connect-to and turn-on the power.
Plug the other end of the power cord into a power outlet and turn it on.
Picture may differ from product supplied for your region.
Turn on the monitor by pressing the power button on the front of the monitor.
Turn on the computer too, and follow the instructions in
Getting the most from your BenQ monitor on page 13
to install the monitor software.
Downloaded from ManualMonitor.com Manuals
How to assemble your monitor hardware 9
How to detach the stand base
1. Prepare the monitor and area.
Turn off the monitor and the power before unplugging the power cable. Turn off the computer before unplugging the monitor signal cable.
Please be careful to prevent damage to the monitor.
Placing the screen surface on an object like a stapler or a mouse will crack the glass or damage the LCD substrate voiding your warranty. Sliding or scraping the monitor around on your desk will scratch or damage the monitor surround and controls.
Protect the monitor and screen by clearing a flat open area on your desk and placing a soft item like a towel on the desk for padding, before laying the screen face down on a flat clean padded surface.
2. Release the locking clip on one side of the stand base while pulling the edge of the base away from the stand arm.
3. Release the other locking clip to detach the stand base from the monitor stand arm.
10 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
How to use the monitor wall mounting kit
The back of your LCD monitor has a VESA standard mount with 100mm pattern, allowing the installation of a wall mount bracket. Before starting to install a monitor wall mounting kit, please read the precautions carefully.
Precautions:
• Install your monitor and monitor mounting kit on a wall with flat surface.
• Ensure that the wall material is stable to support the weight of the monitor.
• Turn off the monitor and the power before disconnecting the cables from the LCD monitor.
1. Remove the monitor base.
Lay the screen face down on a clean and well-padded sur-
face. Detach the monitor base as instructed in “
How to detach the stand base on page 10
2. Remove the monitor stand.
Use a a cross-pointed screwdriver to release the screws that fixing the monitor stand to the monitor.
The use of a magnetic-head screwdriver is recommended to avoid of losing the screws.
Then pull the monitor stand backward away from the monitor.
In case you intend to use your monitor on the stand in the future, please keep the monitor base, monitor stand, and screws somewhere safe for future use.
Downloaded from ManualMonitor.com Manuals
How to assemble your monitor hardware 11
3. Remove the rear cover.
Slide the rear cover back toward you to remove it. The screw plate at the back of the monitor could be revealed.
4. Follow the instruction manuals of the wall mount bracket you purchased to complete the installation.
12 How to assemble your monitor hardware
Downloaded from ManualMonitor.com Manuals
4. Getting the most from your BenQ monitor
To gain the most benefit from your new BenQ color LCD flat screen monitor, you should install the custom BenQ LCD Monitor driver software as provided on the BenQ LCD Monitor CD-ROM.
The circumstances under which you connect and install your BenQ LCD Monitor will determine which process you need to follow to successfully install the BenQ LCD Monitor driver software.
These circumstances relate to which version of Microsoft Windows you are using, and whether you are connecting the monitor and installing the software onto a new computer (without existing monitor driver software), or whether you are upgrading an existing installation (which already has existing monitor driver software) with a newer monitor.
In either case however, the very next time you turn on your computer (after connecting the monitor to your computer), Windows will automatically recognise the new (or different) hardware, and will launch its Found New Hardware wizard.
Follow the wizard instructions until it asks you to select a monitor model. At that point, click the
Have Disk button, insert the BenQ LCD Monitor CD-ROM and select the appropriate monitor model. Further details and step-by-step instructions for both an automatic (new) or upgrade
(existing) installation follow. See:
•
How to install the monitor on a new computer on page 14 .
•
How to upgrade the monitor on an existing computer on page 15
If you require a User Name and Password to login to your Windows computer, you must be logged on as an Administrator or as a member of the Administrators group in order to install the monitor driver software.
Furthermore, if your computer is connected to a network which has security access requirements, network policy settings may prevent you from installing software on your computer.
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 13
How to install the monitor on a new computer
This instruction details the procedure for selecting and installing the BenQ LCD Monitor driver software on a new computer which has never had a monitor driver installed before. This instruction is only suitable for a computer which has never been used before, and for which the
BenQ LCD Monitor is the first ever monitor to be connected to it.
If you are adding the BenQ LCD Monitor to an existing computer that has already had another monitor connected to it (and has monitor driver software installed), you should not be following these instructions.
You should instead be following the instructions for How to upgrade the monitor on an existing computer.
1. Follow the instructions in
How to assemble your monitor hardware on page 7 .
When Windows (2000 or later) starts, it will automatically detect the new monitor and launch the
Found New Hardware Wizard. Follow the prompts until it displays the option to Install Hardware
Device drivers.
2. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer.
3. Check Search for a suitable driver for my device option, and click Next.
4. Check the option for CD-ROM drives (uncheck all others) and click Next.
5. Look to confirm that the wizard has selected the correct name of your monitor as “BenQ
FP72ES/FP92ES” and click Next.
6. Click Finish.
7. Restart the computer.
14 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
How to upgrade the monitor on an existing computer
This instruction details the procedure for manually updating the existing monitor driver software on your Microsoft Windows computer. It is currently tested as compatible (and recommended only) for Windows 2000 and Windows XP Operating System (OS).
The BenQ LCD Monitor driver for your model may well function perfectly with other versions of Windows, however, as at the time of writing, BenQ has done no testing of this driver on other versions of Windows and cannot guarantee its operation on those systems.
Installing monitor driver software involves selecting an appropriate information file (.inf) on the
BenQ LCD Monitor CD-ROM for the particular model monitor you have connected, and letting
Windows install the corresponding driver files from the CD. You need only steer it in the right direction. Windows has an Upgrade Device Driver Wizard to automate the task and guide you through the file selection and installation process.
See:
•
How to install on Windows XP system on page 16
.
•
How to install on Windows 2000 system on page 18 .
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 15
How to install on Windows XP system
1. Open Display Properties.
The quickest shortcut to Display Properties is through the Windows desktop.
Right-click the desktop and select Properties from the popup menu.
Alternatively, the Windows menu to Display Properties is located in Control Panel.
In Windows XP version, Control Panel is located directly under the main Start menu item.
The menu options displayed will depend upon which type of view is selected for your system.
•
Under the Classic view, click Start | Control Panel | Display.
•
Under the Category view, click Start | Control Panel | Appearance and Themes | Change the screen resolution.
The Display Properties window will display.
2. Click the Settings tab and the Advanced button.
The Advanced Display Properties window will display.
3. Click the Monitor tab and select the ‘Plug and Play Monitor’ from the list.
If there is only one monitor in the list, it will already be selected for you.
4. Click the Properties button.
The Monitor Properties window will display.
If the driver provider is listed as BenQ, and the model matches that of your new monitor, the proper drivers are already installed, and you need do nothing further. Cancel out of these property windows.
However, if BenQ is not listed as the manufacturer, or the correct model is not currently shown, you will need to continue with these instructions.
5. Click the Driver tab and the Update Driver button.
The Hardware Update Wizard will display. Follow the wizard instructions noting the steps below:
6. Insert the BenQ LCD Monitor CD-ROM into a CD drive on the computer you attached the monitor to.
7. Check the option ‘Install from a list or specific location’ and click Next.
8. Check the option ‘Search for the best driver in these locations’ and also check ‘Search removable media’, then click Next.
Please wait while the wizard searches for drives and the BenQ LCD Monitor CD inserted in step 6.
When complete, the wizard should have found and selected the BenQ driver on the CD appropriate to your monitor model, in this case ‘BenQ FP72ES/FP92ES’ in the location
‘d:\driver\BenQFP72ES.inf/BenQFP92ES.inf ’ or similar.
The drive letter for your CD drive may differ from the example above depending upon your system – it may be ‘D:’ or ‘E:’ or ‘F:’ etc.
9. Select (single-click) the file named ‘BenQ FP72ES/FP92ES’ on the CD, and click the Next button.
This will copy and install the appropriate monitor driver files to your computer.
10. Click Finish.
This will close the wizard and return you to the Monitor Properties window, now renamed BenQ
FP72ES/FP92ES Properties.
16 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
11. Click Close, OK, and OK.
This will close the Display Properties windows. You do not need to restart Windows XP, as the BenQ
LCD monitor drivers will operate immediately with no further action required by you.
Downloaded from ManualMonitor.com Manuals
Getting the most from your BenQ monitor 17
How to install on Windows 2000 system
You do not need to follow this instruction if you are installing onto a computer which has a Windows XP (or later) version system. In that case, see the instructions at
How to install on Windows XP system on page 16
1. Open Display Properties.
The quickest shortcut to Display Properties is through the Windows desktop.
Right-click the desktop and select Properties from the popup menu.
Alternatively, the Windows menu to Display Properties is located in Control Panel.
In Windows 2000 version, Control Panel is located under the Settings menu item.
Click Start | Settings | Control Panel | Display.
The Display Properties window will display.
2. Click the Settings tab and the Advanced button.
The Advanced Display Properties window will display.
3. In Windows 2000, click the Monitor tab and the Properties button.
The Monitor Properties window will display.
4. In Windows 2000, click the Driver tab and the Update Driver button.
The Upgrade Device Driver Wizard will display.
See How to complete the Windows Upgrade Device Driver Wizard on page 19
.
18 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
How to complete the Windows Upgrade Device Driver Wizard
1. Load the BenQ LCD Monitor CD-ROM which came with your monitor.
Insert the CD-ROM into a CD drive on the computer you attached the monitor to.
The autorun User’s Guide language selection page will display in your web browser.
You can select a language and view the online version of this manual from the next window.
You could then print it out for reference if you wish to work off-line. When you’re ready, Cancel the browser as it is not required for the Windows Upgrade Device Driver Wizard.
2. Launch the Windows Upgrade Device Driver Wizard and click Next.
3. Check the option ‘Display a list of known drivers...’ and click Next.
4. Click the Have Disk button.
The Install From Disk window will display.
5. Click the Browse button and navigate to the BenQ LCD Monitor CD-ROM.
This is the CD you loaded in step 1 above. The CD Drive will have a Windows designated drive letter
(like D: or E: or F:). Select the drive letter corresponding to the drive you put the CD into.
6. Double-click the folder labelled ‘Driver’.
The contents of the ‘Driver’ folder will display.
7. Click the Open button.
This will return you to the Install from Disk window, and it will have entered the address to the BenQ
LCD Monitor CD ‘Driver’ folder into the field titled ‘Copy manufacturer’s files from:’.
The field will contain something like
,
“D:\Driver”, or “E:\Driver”, or “F:\Driver”.
8. Click the OK button.
This will return you to the Upgrade Device Driver Wizard.
9. Select (single-click) the file named BenQ FP72ES/FP92ES, and click the Next button.
10. Click Next.
This will copy the appropriate monitor driver files to your computer.
11. Click Finish.
On Windows 2000, this will close the wizard and return you to the Monitor Properties window, now renamed ‘BenQ FP72ES/FP92ES Properties’.
Should you wish to do so, this is where you can change the screen refresh rate and other monitor properties to suit your needs. See
How to adjust the screen refresh rate on page 22 for details.
12. In Windows 2000, click Close.
This will close the BenQ FP72ES/FP92ES Properties window and return you to the Advanced Display
Properties window.
13. In Windows 2000, click OK.
This will close the Advanced Display Properties window, and return you to the Display Properties window.
Should you wish to do so, this is where you can change the screen resolution (area and color).
See
How to adjust the screen resolution on page 21
for details.
Getting the most from your BenQ monitor 19
Downloaded from ManualMonitor.com Manuals
14. Click OK.
This will close the Display Properties window, and if you made any changes to the screen resolution,
Windows 2000 will prompt you for confirmation to effect the changes, and further confirmation to accept the changes. Click OK and Yes respectively.
20 Getting the most from your BenQ monitor
Downloaded from ManualMonitor.com Manuals
5. How to adjust the screen resolution
Due to the nature of liquid crystal display (LCD) technology, the picture resolution is always fixed.
The best possible picture for your FP72E S/FP92E S is achieved with a resolution of 1280 x 1024.
This is called “Native Resolution” or maximal resolution – that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit. Image blurring across pixel boundaries can occur with the interpolated resolution depending upon the image type and its initial resolution.
To take full advantage of LCD technology you should select the native resolution setting of 1280 x 1024.
1. Open Display Properties and select the Settings tab.
You can open Display Properties by right-clicking on the Windows desktop and selecting Properties from the pop-up menu.
2. Use the slider in the ‘Screen area’ section to adjust the screen resolution.
Select the recommended resolution of 1280 x 1024 then click Apply.
If you select some other resolution, be aware that this other resolution is interpolated and may not accurately display the screen image as well as it could do at the native resolution setting.
3. Click OK then Yes.
4. Close the Display Properties window.
Downloaded from ManualMonitor.com Manuals
How to adjust the screen resolution 21
6. How to adjust the screen refresh rate
You don’t have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. There is a table with the factory modes in the specification
Supported PC Timings on page 39
You can choose 60, 70 and 75 Hertz, (but not 72Hz) for the native resolution of 1280 x 1024.
1. Double click the Display icon in Control Panel.
2. From the Display Properties window, select the Settings tab and click the Advanced button.
3. Select the Adapter tab, and select an appropriate refresh rate to match one of the applicable factory modes as listed in the specification table.
4. Click Change, OK, then Yes.
5. Close the Display Properties window.
22 How to adjust the screen refresh rate
Downloaded from ManualMonitor.com Manuals
7. Picture optimization
The easiest way to obtain an optimal display from an analog (D-Sub) input is to use the i key function. Press the
i key to optimize the currently displayed image to the screen.
When you connect a digital video output using a digital (DVI) cable to your monitor, the i key and the Auto
Adjustment function will be disabled, because the monitor will automatically display the best image.
Please ensure that the connected graphic card on your computer is set to the native resolution of the monitor (1280 x 1024) when you use the i key function.
If you wish, you can always adjust the screen geometric settings manually using geometry menu items. To assist you in this endeavour, BenQ has provided a screen test image utility which you can use to check for screen color, grayscale and line gradient display.
1. Run the test program auto.exe from CD-ROM. You could also use any other image, such as the desktop of your operating system. However, we recommend that you use auto.exe. As you run auto.exe, a test pattern displays.
2. Press the
i key on the monitor.
3. Press the MENU key to access the monitor On-Screen Display (OSD) menu.
4. Use the
W
or
X
keys to select DISPLAY and press the ENTER key to enter the menu.
5. If you notice a vertical noise (like a curtain effect-shimmering of vertical lines), press the
W or
X
keys to select Pixel Clock and press the ENTER key. Then press the
W
or
X
keys to adjust the monitor until the noise disappears.
6. If you notice a horizontal noise, press the
W
or
X
keys to select Phase and press the ENTER key. Then press the
W
or
X
keys adjust the monitor until the noise disappears.
Downloaded from ManualMonitor.com Manuals
Picture optimization 23
8. How to adjust your monitor
The control panel
1. “ i key”: Adjust vertical position, phase, horizontal position and pixel clock automatically.
2. “MENU” key: Activate OSD main menu and return to the previous menu or exit OSD.
3.
W
(Left) key: For Left/Decrease adjustment. Left key is the hot key for Contrast.
4.
X
(Right) key: For Right/Increase adjustment. Right key is the hot key for Brightness.
5. “ENTER” key: Enter sub menus and select items. The key is also the hot key for Volume.
6. “Power”: Turn the power on or off.
OSD = On Screen Display.
The hot-keys will display a graduated scale for adjusting the value of that setting, and will only operate while the OSD menu is not currently displaying. Hot-key displays will disappear after a few seconds of no
24 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
On Screen Display (OSD) menu structure
DISPLAY
PICTURE
Auto Adjustment
H. Position
V. Position
Pixel Clock
Phase
Brightness
Contrast
Sharpness
Color
PICTURE
ADVANCED
AUDIO
Picture Mode
Senseye Demo
Volume
Mute
Normal
Bluish
Reddish
User Mode
Reset Color
Standard
Movie
Dynamics
Photo sRGB
ON
OFF
ON
OFF
SYSTEM Input
OSD Settings
Information
Reset All
DVI
D-sub
Language
H. Position
V. Position
Display Time
OSD Lock
YES
NO
Red
Green
Blue
YES
NO
English
Français
Deutsch
Italiano
Español
Polski/ 日本語
Česky/ 繁體中文
Magyar/ 简体中文
Srpskohrvatski
(jezik)
Română
Nederlands
Русский
Svenska
Português
ON
OFF
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 25
Hot key mode
The monitor keys perform as hotkeys to provide direct access to particular functions whenever the menu isn't currently displaying on-screen.
Brightness hot key
Press the
X
key to display the Brightness indicator. Further press the
X
key to increase or the
W
key to decrease the screen brightness, and press the MENU key to exit.
Contrast hot key
Press the
W
key to display the Contrast indicator. Further press the
X
key to increase or the
W
key to decrease the screen contrast, and press the MENU key to exit.
Volume hot key
Press the ENTER key to enter the Volume indictor. Further press the
X
key to increase or the
W
key to decrease the volume, and press the MENU key to exit.
26 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Main menu mode
You can use the OSD (On Screen Display) menu to adjust all the settings on your monitor.
Press the MENU key to display the following main OSD menu.
1
2 3
4
5
There are five main OSD menus:
1. Display
2. Picture
3. Picture Advanced
4. Audio
5. System
Use the
W
(left) or
X
(right) keys to highlight a menu item, and press the ENTER key to enter the Menu item settings.
There are 14 different menu languages, see “
” under “OSD Settings” for more details.
For more information on each menu, please refer to the following pages:
• Picture Advanced menu on page 32
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 27
Display menu
1. Press the MENU key to display the main menu.
2. Press the
W
or
X
keys to select DISPLAY and then press the ENTER key to enter the menu.
3. Press the
W
or
X
keys to move the highlight to a menu item and then press the ENTER key to select that item.
4. Press the
W
or
X
keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU button.
Item
Auto
Adjustment
Function
Optimizes and adjusts the screen settings automatically for you. The
i key is a ‘hot-key’ for this function.
Operation
Press the ENTER key to select this option and make adjustment.
When you connect a digital video output using a digital (DVI) cable to your monitor, the i key and the Auto
Adjustment function will be disabled.
Range
28 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
H. Position
V. Position
Pixel Clock
Phase
Adjusts the horizontal position of the screen image.
Adjusts the vertical position of the screen image.
Adjusts the pixel clock frequency timing to synchronize with the analog input video signal.
Not applicable to a digital input signal.
Press the
W
or
X
keys to adjust the value.
Picture optimization on page 23
Adjusts the pixel clock phase timing to synchronize with the analog input video signal.
Not applicable to a digital input signal.
Picture optimization on page 23
0 to 100
0 to 100
0 to 100
0 to 63
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 29
Picture menu
1. Press the MENU key to display the main menu.
2. Press the
W
or
X
keys to select PICTURE and then press the ENTER key to enter the menu.
3. Press the
W
or
X
keys to move the highlight to a menu item and then press the ENTER key to select that item.
4. Press the
W
or
X
keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU button.
Item
Brightness
Contrast
Sharpness
Function
Adjusts the balance between light and dark shades.
Adjusts the degree of difference between darkness and lightness.
Adjusts the clarity and visibility of the edges of the subjects in the image.
Color - Press ENTER to enter the Color menu.
Normal Allows video and still photographs to be viewed with natural coloring. This is the factory default color.
Bluish Applies a cool tint to the image and is factory pre-set to the PC industry standard white color.
Press the
W
or
X
keys to select this option.
Reddish Applies a warm tint to the image and is factory pre-set to the news print standard white color.
Operation
Press the
X
key to increase the brightness and press the
W
key to decrease the brightness.
Press the
X
key to increase the contrast and press the
W
key to decrease the contrast.
Press the
X
key to improve the crispness of the display and press the
W
key to have softness effect on the display.
Range
0 to 100
0 to 100
1 to 5
30 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
User Mode Tailors the image color tint. The blend of the Red,
Green and Blue primary colors can be altered to change the color tint of the image. The default start setting is 50. Decreasing one or more of the colors will reduce their respective influence on the color tint of the image. e.g. if you reduce the Blue level the image will gradually take on a yellowish tint. If you reduce Green, the image will become a magenta tint.
Press MENU to leave the Color menu.
Reset Color Resets the User Mode custom color settings to the factory defaults.
Press the
W
or
X
keys and the ENTER key to select
Red, Green, or Blue. Then use the
W
or
X
keys to make the color adjustments.
Press the
W
or
X
keys to change the settings.
• Red
(0 to 100)
• Green
(0 to 100)
• Blue
(0 to 100)
• Yes
• No
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 31
Picture Advanced menu
1. Press the MENU key to display the main menu.
2. Press the
W
or
X
keys to select PICTURE
ADVANCED and then press the ENTER key to enter the menu.
3. Press the
W
or
X
keys to move the highlight to a menu item and then press the ENTER key to select that item.
4. Press the
W
or
X
keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU button.
Item Function
Picture Mode
Selects a picture mode that best suits the type of images shown on the screen.
• Standard - for basic PC application.
• Movie - for viewing videos.
• Dynamics - for viewing landscape-specific videos and playing games.
• Photo - for viewing still images.
• sRGB - for better color matching representation with the peripheral devices, such as printers,
DSCs, etc.
Operation
Press the
W
or
X
keys to adjust the value.
Range
• Standard
• Movie
• Dynamics
• Photo
• sRGB
32 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
Senseye Demo
Displays the preview of screen images under the selected mode from Picture Mode. The screen will be divided into two windows; the left window demonstrates images of
Standard mode, while the right window presents the images under the specified mode.
Press the
W
or
X
keys to change the settings.
• ON
• OFF
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 33
Audio menu
Item
Volume
Mute
1. Press the MENU key to display the main menu.
2. Press the
W
or
X
keys to select AUDIO and then press the ENTER key to enter the menu.
3. Press the
W
or
X
keys to move the highlight to a menu item and then press the ENTER key to select that item.
4. Press the
W
or
X
keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU button.
Function
Adjusts the level of volume.
Mutes the audio input.
Operation
Press the
X
key to increase the volume and press the
W key to decrease the volume.
Press the
W
or
X
keys to change the settings.
Range
0 to 100
• ON
• OFF
34 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
System menu
1. Press the MENU key to display the main menu.
2. Press the
W
or
X
keys to select SYSTEM and then press the ENTER key to enter the menu.
3. Press the
W
or
X
keys to move the highlight to a menu item and then press the ENTER key to select that item.
4. Press the
W
or
X
keys to make adjustments or selections.
5. To return to the previous menu, press the
MENU button.
Item
Input
Function
Selects the D-sub (analog) or DVI (digital) input. Use this to change the input to that appropriate to your video cable connection type.
Operation
Press the
W
or
X
keys to change the settings.
OSD Settings - Press ENTER to enter the OSD Settings menu.
Range
• DVI
• D-sub
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 35
Language Sets the OSD menu language.
Press the
W
or
X
keys to adjust the value.
The language options displayed on your OSD may differ from those shown on the right, depending on the product supplied in your region.
• English
• French
• German
• Italian
• Spanish
• Polish/
Japanese
• Czech/
Traditional
Chinese
• Hungarian/
Simplified
Chinese
• Serbo-Croatian
• Romanian
• Dutch
• Russian
• Swedish
• Portuguese
0 to 100 H. Position Adjusts the horizontal position of the OSD menu.
V. Position Adjusts the vertical position of the OSD menu.
Display Time Adjusts the display time of the OSD menu.
Press the
W
or
X
keys to change the settings.
0 to 100
• 5 sec.
• 10 sec.
• 15 sec.
• 20 sec.
• 25 sec.
• 30 sec.
36 How to adjust your monitor
Downloaded from ManualMonitor.com Manuals
OSD Lock Prevents all the monitor settings from being accidentally changed.
When this function is activated, the OSD controls and hotkey operations will be disabled.
Press the
W
or
X
keys to change the settings.
To unlock the OSD controls when the OSD is preset to be locked, press and hold the ’MENU' key for 15 seconds to enter the 'OSD Lock' option and make changes.
Alternatively, you may use the W or X keys to select ’OFF’ in the 'OSD
Lock' submenu from the
’OSD Settings’ menu, and all OSD controls will be accessible.
Press MENU to leave the OSD Settings menu.
Information Displays the current monitor property settings.
Reset All Resets all mode, color and geometry settings to the factory default values.
Press the ENTER key to select this option.
Press the
W
or
X
keys to change the settings.
• ON
• OFF
• Yes
• No
Downloaded from ManualMonitor.com Manuals
How to adjust your monitor 37
9. Troubleshooting
Frequently asked questions (FAQ)
The image is blurred:
Read the
How to adjust the screen resolution on page 21
section, and then select the correct
resolution, refresh rate and make adjustments based on these instructions.
How do you use a VGA extension cable?
Remove the extension cable for the test. Is the image now in focus? If not, optimize the image by working through the instructions in the
How to adjust the screen refresh rate on page 22
section It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a built-in booster.
Does the blurring only occur at resolutions lower than the native (maximum) resolution?
Read the
How to adjust the screen resolution on page 21
section. Select the native resolution.
Pixel errors can be seen:
One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color.
• Clean the LCD screen.
• Cycle power on-off.
• These are pixels that are permanently on or off and is a natural defect that occurs in LCD technology.
The image has a faulty coloration:
It has a yellow, blue or pink appearance.
Select MENU > PICTURE > Color > Reset Color, and then choose “Yes” in the “Caution” message box to reset the color settings to the factory defaults.
If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
No image can be seen:
Is the prompt on the display illuminated in green?
If the LED is illuminated in green and there is a message “Out of Range” on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one
of the supported mode. Please read “
Supported PC Timings on page 39
Faint shadow from the static image displayed is visible on the screen:
• Activate the power management function to let your computer and monitor go into a low power "sleep" mode when not actively in use.
• Use a screensaver to prevent the occurrence of image retention.
Is the prompt on the display illuminated in orange?
38 Troubleshooting
Downloaded from ManualMonitor.com Manuals
If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support.
Is the prompt on the display not illuminated at all?
Check the power supply mains socket, the external power supply and the mains switch.
The image is distorted, flashes or flickers:
How to adjust the screen resolution on page 21
section and then select the correct resolution, refresh rate and make adjustments based on these instructions.
The image is displaced in one direction:
How to adjust the screen resolution on page 21
section and then select the correct resolution, refresh rate and make adjustments based on these instructions.
The OSD controls are inaccessible:
• To unlock the OSD controls when the OSD is preset to be locked, press and hold the “MENU” key for 15 seconds to enter the “OSD Lock” option and make changes.
• Alternatively, you may use the
W
or
X
keys to select “OFF” in the “OSD Lock” submenu from the “OSD Settings” menu (under SYSTEM), and all OSD controls will be accessible.
Need more help?
If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: [email protected]
Downloaded from ManualMonitor.com Manuals
Troubleshooting 39
10. Supported PC Timings
Incoming display mode (Input timing)
Resolution Horizontal
Frequency (KHz)
640x350
720x400
31.47(P)
31.47(N)
640x480
640x480
640x480
640x480
31.47(N)
35.00(N)
37.86(N)
37.50(N)
800x600
800x600
800x600
800x600
35.16(P)
37.88(P)
48.08(P)
46.87(P)
832x624 49.72(N)
1024x768 48.36(N)
1024x768 56.48(N)
1024x768 60.02(P)
1152x864 67.50(P)
1152x870 68.68(N)
1152x900 61.80(N)
1152x900 71.81(N)
1280x1024 64.00(P)
1280x1024 75.83(N)
1280x1024 80.00(P)
1280x1024 81.18(N)
Vertical
Frequency (Hz)
70.08(N)
70.08(P)
60.00(N)
67.00(N)
72.80(N)
75.00(N)
56.25(P)
60.32(P)
72.19(P)
75.00(P)
74.55(N)
60.00(N)
70.10(N)
75.00(P)
75.00(P)
75.06(N)
66.00(N)
76.14(N)
60.00(P)
71.53(N)
75.00(P)
76.16(N)
108.00
100.00
94.50
108.00
108.00
128.00
135.00
135.09
36.00
40.00
50.00
49.50
57.29
65.00
75.00
78.75
Pixel
Frequency (MHz)
25.17
28.32
25.18
30.24
31.50
31.50
Comment
DOS
DOS
DOS
Macintosh
VESA
VESA
VESA
VESA
VESA
VESA
Macintosh
VESA
VESA
VESA
VESA
Macintosh
SUN 66
SUN
VESA
IBMI
VESA
SPARC2
• Modes not listed in the table may not be supported. For an optimal picture, we recommended you choose a mode listed in the table above.
• There are 22 available modes that are compatible with Windows.
• Image disruption may occur as a result of signal frequency differences from graphic cards which do not correspond with the usual standard. This is not, however, an error. You may improve this situation by altering an automatic setting or by manually changing the phase setting and the pixel frequency from the “DISPLAY” menu.
• If you switch off the monitor, interference lines can occur on your screen. But do not be concerned about this, as it is normal.
• To extend the service life of the product, we recommend that you use your computer's power management function.
40 Supported PC Timings
Downloaded from ManualMonitor.com Manuals
11. Specifications
BenQ FP72E S
Model
Display type
Viewable diagonal
Native (maximum) resolution
Colors
Contrast / Brightness
Response time
Viewing angle (left/right, up/down)
Line frequency
FP72E S
17.0”, active, TFT
43.2 cm
1,280 x 1,024
16.7 million
800:1 / 300 cd/m
2
5 ms
160, 160 (CR>10)
170, 170 (CR>5)
31 - 83 kHz Multi- frequency monitor
Image frequency
Image diagnostics
Controls
Functions
Power management
Max. power consumption
Standby power consumption
50 - 76 Hz modes within these parameters
Digital, OSD Technology, i key (automatic image setting)
5 buttons and i key.
Contrast, brightness, vert. & hor. image position, phase, pixel clock, color balance, color palette, multiple-language OSD, OSD position, input selection, picture mode, Senseye demo
VESA DPMS, EPA
45 Watt
< 1 Watt
Input signal
PC
Speaker
Synchronization
Temperature (operating)
Air humidity (operating)
Certifications
Downloaded from ManualMonitor.com Manuals
RGB analog 0.7 Vpp/75 Ohm positive
Digital: DVI-D (optional)
1 W x 2
TTL separate signal connection 15-pin mini D-sub cable
0 °C - 40 °C
10% - 90%
TCO 03, TÜV/Ergonomics, TÜV/ GS, FCC Class
B, ISO 13406-2, VCCI, CB Report, CE, C-Tick,
BSMI, Fimko, GOST, CSA, CCC, eK
Specifications 41
Operating voltage
Dimensions (H x W x D)
Weight
Automatic switched mode power supply,
100-240 V, 50-60 Hz
369 x 371.6 x 151.3 mm
3.9 kg
42 Specifications
Downloaded from ManualMonitor.com Manuals
BenQ FP92E S
Model
Display type
Viewable diagonal
Native (maximum) resolution
Colors
Contrast / Brightness
Response time
Viewing angle (left/right, up/down)
Line frequency
FP92E S
19.0”, active, TFT
480 mm
1,280 x 1,024
16.7 million
800:1 / 300 cd/m
2
5 ms
160, 160 (CR>10)
31 - 83 kHz Multi- frequency monitor
Image frequency
Image diagnostics
Controls
Functions
Power management
Max. power consumption
Standby power consumption
50 - 76 Hz modes within these parameters
Digital, OSD Technology, i key (automatic image setting)
5 buttons and i key.
Contrast, brightness, vert. & hor. image position, phase, pixel clock, color balance, color palette, multiple-language OSD, OSD position, input selection, picture mode, Senseye demo
VESA DPMS, EPA
50 Watt
< 1 Watt
Input signal
PC
Speaker
Synchronization
Temperature (operating)
Air humidity (operating)
Certifications
RGB analog 0.7 Vpp/75 Ohm positive
Digital: DVI-D (optional)
1 W x 2
TTL separate signal connection 15-pin mini D-sub cable
0 °C - 40 °C
10% - 90%
TCO 03, TÜV/Ergonomics, TÜV/ GS, FCC Class
B, ISO 13406-2, VCCI, CB Report, CE, C-Tick,
BSMI, Fimko, GOST, CSA, CCC, eK
Specifications 43
Downloaded from ManualMonitor.com Manuals
Operating voltage
Dimensions (H x W x D)
Weight
Automatic switched mode power supply,
100-240 V, 50-60 Hz
409.2 x 408.8 x 167 mm
4.8 kg
44 Specifications
Downloaded from ManualMonitor.com Manuals
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project