Zanussi ZGF 983 Technical data

TABLE DE CUISSON
GASKOOKPLAAT
GASKOCHMULDE
GAS HOB
ZGF 983
NOTICE D'UTILISATION
GEBRUIKSAANWIJZING
GEBRAUCHSANLEITUNG
INSTRUCTION BOOKLET
BE
ENGLISH
☛ For Your Safety
These warnings are provided in the interest of safety. You
installing or using the appliance.
MUST
read them carefully before
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred, always ensure that the book is left with
the appliance in order that the new owner can get to know the functions of the appliance and
the relevant warnings.
During Operation
•
•
•
•
•
•
•
•
•
This appliance has been designed to be operated by
adults and children under supervision. Young children
MUST NOT be allowed to tamper with the controls or
play near or with the oven.
This appliance has been designed for cooking
edible foodstuff and to be used for domestic nonprofessional purposes only. It must not be used for
any other purpose.
It is dangerous to alter the specification in any way.
For hygiene and safety reasons, this appliance should
be kept clean at all times. A build-up of fats or other
foodstuff could result in a fire.
Accessible parts of this appliance may become hot
when it is in use. Children should be KEPT AWAY until
it has cooled.
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
unexperienced persons may cause injury or serious
malfunctioning. Refer to your local Zanussi Service
Centre. Always insist on genuine Zanussi spare
parts.
Ensure that all control knobs are in the OFF position
when not in use.
Should you connect any electrical tool to a plug near
this cooking appliance, ensure that electric cables
are not in contact with it and keep them far enough
from the heated parts of this appliance.
If the appliance is out of order, disconnect it from the
electric supply.
MANUFACTURER:
ELECTROLUX ZANUSSI S.p.A.
Viale Bologna 298 - 47100 FORLI’ (Italy)
About Installation, Cleaning
and Manteinance
•
•
•
•
•
•
•
•
-
It is mandatory that all operations required for the
installation are carried out by a qualified or competent
person, in accordance with existing rules and
regulations.
Disconnect the appliance from the electrical supply,
before carrying out any cleaning or manteinance
work.
Ensure a good ventilation around the appliance. A
poor air supply could cause lack of oxygen.
Ensure that the gas supply complies with the gas
type stated on the identification label, placed near
the gas supply pipe.
Using a gas cooking appliance will produce heat
and moisture in the room which it has been
installed in. Ensure a continuous air supply,
keeping the air vents in good conditions or
installing a cooker hood with discharge tube.
In case of intensive or long time use of the
appliance, make the ventilation more efficient,
by opening a window or increasing the electric
exhaust fan power.
Once you removed all packaging from the appliance,
ensure that it is not damaged and the electric cable
is in perfect conditions. Otherwise, contact your
dealer before proceeding with the installation.
The manufacturer disclaims any responsability
should all the safety measures not be carried
out.
This appliance complies with the following
E.E.C. Directives:
73/23 - 90/683 (Low Voltage Directive);
89/336 (Electromagnetical Compatibility Directive);
90/396 (Gas Appliances)
93/68 (General Directives)
and subsequent modifications.
These instructions are only for the countries stated by the symbol
printed on the front cover of this instruction book.
33
Contents
1. Instruction for the User ............. Pag.
34
5. Electrical Connection ................ Pag.
37
2. Cleaning and Maintenance ....... Pag.
35
6. Adaptation to different
types of gas................................ Pag.
38
3. Technical Data ........................... Pag.
36
7. Building In .................................. Pag.
39
4. Instruction for the Installer ....... Pag.
36
Guarantee ................................... Pag.
42
1. Instruction for the User
HOB BURNERS CONTROL KNOBS
The hob burners control knobs are situated on the hob
front panel. The symbols on the knobs mean that :
●
Carefully supervise cookings with fats or oil,
since these types of foodstuff can result in a fire,
if over-heated.
there is no gas supply
there is maximum gas supply
there is minimum gas supply
LIGHTING THE BURNERS
•
For easier lighting, proceed before putting a pan
on the pan support.
Press the automatic ignition switch marked with a
small spark. Push the relevant burner control knob
down and turn it anti-clockwise until it reaches the
"maximum" position.
After lighting the flame, keep the knob pushed down
for about 5 seconds. This will allow the
"thermocouple" (Fig. 1 lett. D) to be heated and the
safety device to be switched off, otherwise the gas
supply would be interrupted.
Then, check the flame is regular and adjust it as
required.
If you cannot light the flame even after several
attempts, check the "cap" (Fig. 1 lett. A) and the
"crown" (Fig. 1 lett. B) are in the correct position.
To put the flame out, turn the knob to the symbol ●.
•
34
FO 0204
Always turn the flame down or put it out before
taking the pans off the burner.
USING THE HOB CORRECTLY
To ensure maximum burner efficiency, it is strongly
recommended that you use only pots and pans with a
bottom fitting the size of the burner used, so that flame
will not spread beyond the bottom of the vessel (see the
table beside).
It is also advisable, as soon as a liquid starts boiling, to
turn down the flame so that it will barely keep the liquid
simmering.
•
Fig. 1
Use only pans or pots with flat bottom.
Burner
Double Crown
Big (rapid)
Medium (semirapid)
Small (Auxiliary)
minimum
diameter
180 mm
160 mm
120 mm
80 mm
maximum
diameter
260 mm
260 mm
220 mm
160 mm
THE HOB LID
In order to make the appliance match with the kitchen
design, a lid (not provided) can be fitted on the hob.
● Always clean the lid from cooking residues before
opening it or taking it off.
● The lid is meant to avoid dust to settle on the hob,
when it is closed, and to collect splashes of oil or
fat, when it is open. Do not use it for any other
purpose.
● WARNING! The crystal lid can splinter when
overheated. Always ensure all the burners are
off before closing it.
● Always wipe off any splash of liquid before
opening the lid.
2. Cleaning and Maintenance
•
Disconnect the appliance from the electrical
supply, before carrying out any cleaning or
manteinance work.
Wash the enamelled components with warm soapy
water. Never use abrasive cleaners
Frequently wash the "caps" and the "crowns" with hot
soapy water, carefully taking away any built-up of food.
Carefully wash the stainless steel components with
water, then wipe them dry with a soft cloth.
The pan supports are dishwasher proof.
If the marks are particularly difficult to remove, use
common non-abrasive cleaners or specific products.
Never use steel wool pads or acids.
In models provided with electric ignition, this feature is
obtained through a ceramic "candle" and a metal
electrode (fig. 1 lett. C). Keep these components well
clean, to avoid difficult lighting, and check that the
burner crown holes (lett. B) are not obstructed.
FO 2347
PAN SUPPORTS
To keep the pan supports in the right position, they are
hooked to a couple of special hinges in the back of the
hob.
Thanks to these hooks, you can lift the pan supports
for easier cleaning, as shown in fig. 2.
To take the pan supports completely off the hob,
proceed as shown in fig. 3.
PERIODIC MAINTENANCE
Periodically ask your local Service Centre to check the
conditions of the gas supply pipe and the pressure
adjuster, if fitted.
To ensure the good operation of the hob and its safety
features, it is necessary that the taps are periodically
lubricated.
Fig. 2
FO 2032
● The periodic lubrication of the taps must be
carried out by qualified personnel, which you
must refer to also in case of malfunctioning.
Fig. 3
35
3. Technical Data
Gas Burners Rating
Double Crown Burner
3,5 kW
Rapid Burner (big)
3 kW (G20) - 2,8 kW (G30-31)
Auxiliary Burner (small)
Semirapid Burner (medium)
Class 3 Appliance
Category
Setting
1 kW
2 kW
II 2E+3+
Natural Gas 20 mbar / G25 25 mbar
Gas connection
Electric Supply
HOB RECESS
DIMENSIONS
Length
Width
G 1/2"
230 V 50 Hz
830 mm.
480 mm.
4. Instruction for the Installer
● The side walls of the unit in which the hob is
going to be installed, must not exceed the height
of the working top.
● Avoid installing the appliance in the proximity of
inflammable materials (e.g. curtains, tea towels
etc.).
● The following instructions about installation and
maintenance must be carried out by qualified
personnel in compliance with the regulation in
force. The regulation to be applied for this type of
installation is NBN D 5I.003 : "Installations
functioning with combustible gas lighter than
air".
● The appliance must be electrically disconnected
before all interventions. If any electric supply to
the appliance is required to carry out the work,
ensure all the necessary precautions are
followed.
A) Ramp with ending nut
B) Seal
C) Adjustable connection
GAS CONNECTION
It is indispensible that the connection to the gas mains
are carried out by means of an AGB tap. Choose fixed
connections or use a flexible pipe in AGB (stainless
steel).
If using flexible metallic pipes, be careful they do not
come in contact with mobile parts or they are not
squeezed. Use the same attention when the hob is
combinated with an oven.
This hob can be operated by Slochteren gas (G25) with
a nominal pressure of 25 mbar or by natural gas with
nominal pressure of 20 mbar. No regulation is required
for use by these two types of gas.
Before fitting the appliance ensure that the installation
has the correct voltage for the appliance. At full capacity,
the drop in pressure must not exceed 5%. Such a drop
in pressure is caused by the following parameters:
-
maximum capacity of meter;
-
diameter and lenght of the tube in front and behind
the meter;
-
section of transit of variuos tubes positioned on the
circuit;
-
diameter of eventual connections.
IMPORTANT - To ensure a correct operation, a saving
of energy and the long-life of the appliance, the voltage
pressure of the appliance must correspond to the
recommended values.
The adjustable connection is fixed to the comprehensive
ramp by means of a threaded nut GJ 1/2". Interpose the
sealing between the components as shown in fig. 4.
Screw the parts without forcing, adjust the connection in
the required direction and tighten everything.
FO 2365
36
Fig. 4
IMPORTANT - When the final connection has been
made, it is essential that a thorough leak test is carried
out on the hob and installation. Use some soapy water,
never a flame.
5. Electrical Connection
The appliance is designed to be connected to 230 V
monophase electricity supply.
The connection must be carried out in compliance with
the laws and regulations in force.
Before the appliance is connected:
1) check that the main fuse and the domestic installation
can support the load (see the rating label);
2) check that the power supply is properly earthed in
compliance with the current rules;
3) check the socket or the double pole switch used for
the electrical connection can be easily reached with
the appliance built in the forniture unit.
The appliance is supplied with a connection cable. This
has to be provided with a proper plug, able to support the
load marked on the identification plate. To connect the
plug to the cable, follow the recommendation given in
Fig. 5. The plug has to be fitted in a proper socket.
If connecting the appliance directly to the electric system,
it is necessary that you install a double pole switch
between the appliance and the electricity supply, with a
minimum gap of 3 mm. between the switch contacts and
of a type suitable for the required load in compliance
with the current rules.
The connection cable has to be placed in order that, in
each part, it cannot reach a temperature 90 °C higher
than the room temperature.
The brown coloured phase cable (fitted in the terminal
block contact marked with "L") must always be connected
to the network phase.
Neutral
Earth (yellow/green)
REPLACEMENT OF THE VOLTAGE CABLE
The connection of the voltage cable to the appliance's
terminal block is of type "Y". This means that its
replacement requires the specific equipment of a
technician.
In this case, only cable type H05V2V2-F T90 must be
used. The cable section must be suitable to the voltage
and the working temperature.
The yellow/green earth wire must be approximately 2
cm. longer than the phase wires (Fig. 5).
FO 0073
Fig. 5
To open the terminal block and reach the terminals,
proceed as follows:
● insert the point of a screwdriver into the visible
protrunding part of the terminal block;
● exert a light pressure and lift (Fig. 6)
FO 0257
Fig. 6
37
6. Adaptation to different types of gas
INJECTORS REPLACEMENT
•
•
•
Remove the pan supports.
Remove the burner's caps and crowns.
With a socket spanner 7 unscrew and remove the
injectors (Fig. 7), and replace them with the ones
required for the type of gas in use (see table 2).
• Reassemble the parts, following the same procedure backwards.
• Replace the rating label (placed near the gas supply
pipe) with the relevant one for the new type of gas
supply. You can find this label in the package of the
injectors supplied with the appliance.
Should the feeding gas pressure be different or
variable compared with the required pressure, an
appropriate pressure adjuster must be fitted on the gas
supply pipe, in compliance with the rules in force.
Fig. 7
FO 0392
ADJUSTMENT OF MINIMUM LEVEL
To adjust the minimum level of the burners, proceed as
follows:
• Light the burner.
• Turn the knob on the minimum position.
• Remove the knob.
• With a thin screwdriver, adjust the by-pass screw
(see Fig. 8). If changing from natural gas to LPG,
completely tighten clockwise the screw, until a small
regular flame is obtained.
• Finally check the flame does not go out when quickly
turning the knob from the maximum position to the
minimum position.
This procedure can easily be carried out, anyhow the
hob has been positioned or built in the working top.
Fig. 8
FO 2031
Table 1 : By-pass diameters
Burner
Ø By-pass
in 1/100
of mm.
Double Crown
Auxiliary
Semi-rapid
Rapid
56
28
32
40
Table 2 : injectors - (*) suitable for G25 too.
BURNER
REDUCED
POWER
kW
kW
NORMAL
POWER
NATURAL GAS
G20 - 20 mbar
inj. 1/100
m3/h
LPG
28-30/37 mbar
inj. 1/100 g/h - G30 g/h - G31
Auxiliary (small)
1
0,33
70(*)
0,095
50
72
71
Semi-rapid (medium)
2
0,45
96(*)
0,190
71
145
143
Natural gas :
3
LPG : 2,8
0,65
119(*)
0,286
86
203
200
3,5
1,2
136(*)
0,333
93
254
250
Rapid (big)
Double Crown Burner
38
NORMAL
POWER
7. Building In
A = Auxiliary burner
R = Rapid Burner
SR = Semirapid burner
UR = Double Crown Burner
SR
A
These hobs can be inserted in a built-in kitchen unit
whose depth is between 550 and 600 mm. The hobs
dimensions are shown in Fig. 9.
UR
SR
R
86
0
0
51
Fig. 9
FITTING THE LID
We recommend the lid hinge block are fitted before
installing the hob into the worktop.
To install the lid onto the hob, proceed as follows:
a. Remove the right and left hand grid blocks fitted to
the back of the hob, by unscrewing the relevant
screws (fig. 10)
b. Fit the lid hinge blocks onto the hob, using the
original screws, ensuring that the relevant shims are
fitted between the hinge blocks and the hob (fig. 10);
c. Fit the left hand lid hinge (marked S) into the hinge
block (fig.11);
d. Carry out the same operation with the right hand lid
hinge (marked D).
ADJUSTING THE LID BALANCE
To adjust the lid balance, turn clockwise or anticlockwise the central screw of the right- and left-hand
hinges (fig. 12).
FO 2035
Fig. 10
FO 2037
FO 2036
Fig. 11
Fig. 12
39
30
55 m
480
These hobs can be installed in a kitchen unit with an
opening for insertion whose dimensions are shown in
Fig. 13.
The edge of the cut out must have a minimum distance
from the rear wall of 55 mm.
If there are side walls, or sides of the furniture unit near
the hob, the cut out edges must have a minimum
distance of 150 mm. as shown in Fig. 13.
in.
INSTALLATION AND ASSEMBLY
Carry out the building in of the hob as follows:
830
• put the relevant sealings, supplied with the hob, on
the edges of the cut out, as shown in Fig. 14, taking
care that the sealings meet without overlapping;
150 min
FO 2349
• place the hob in the cut out, taking care of its
Fig. 13
centring;
• fix the hob with the relevant screws (Fig. 15). The
traction of the screws is able to trace the sealing, any
excess of which can then be easily removed.
The edge of the hob forms a double labyrinth seal
which provides a total guarantee against infiltration of
liquids.
FO 2348
Fig. 14
a
FO 0199
a) Joint d'étanchéité
40
Fig. 15
Fig. 17
Fig. 16
a
60
591
Proper arrangements must be
taken in designing the forniture
unit, in order to avoid any contact
with the bottom of the hob which
can be heated when it is operated.
The recommended solution is
shown in Fig. 16.
The panel fitted under the hob
should be easily removable to
allow an easy access if a technical
assistance intervention is needed.
30
480
30
Kitchen unit with door
20 min
POSSIBILITIES FOR
INSERTION
b
380
140
Kitchen unit with oven
The hob recess dimensions must
comply the indication given in
Figs. 17 and 20 and must be
provided with brackets to allow a
continuous supply of air.
To avoid overhating, the building
in should be carried out as shown
in Figs. 18 e 19.
The hob's electric connection and
the oven's one must be carried out
separately, both for safety reasons
and to allow the oven to be easily
taken off the unit.
Hanging forniture units or hoods
must be placed at 650 mm.
minimum from the hob (Fig. 21).
FO 2044
FO 2043
a) Removable panel
b) Space possibly useful for
connections
Fig. 19
Fig. 18
50 cm 2
120 cm 2
360 cm 2
FO 2041
180 cm 2
FO 2042
Fig. 21
Fig. 20
560 min.
650 min
550 min.
FO 0198
FO 2350
41