Enviro 50-1221 Specifications

SHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED PAPER.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
PELLET STOVE
Mini A
TECHNICAL MANUAL
PLEASE READ THIS ENTIRE MANUAL BEFORE
INSTALLATION AND USE OF THIS PELLET BURNING
ROOM HEATER. FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE,
BODILY INJURY OR EVEN DEATH
Contact your building or fire officials about restrictions and installation
inspection requirements in your area.
50-1928
Table of Contents
Introduction...................................................................................................................................3
Rating Label Location................................................................................................................3
Safety Warnings And Recommendations.....................................................................................3
Installation.....................................................................................................................................6
Deciding Where to Locate your Pellet Appliance..........................................................................6
Removing Pellet Stove From Pallet.............................................................................................6
Appliance Dimensions and Specifications....................................................................................7
Hearth Pad (50-1219) Installation..............................................................................................7
Clearances to Combustibles.......................................................................................................8
Alcove Clearances.....................................................................................................................8
Vent Termination Requirements.................................................................................................9
Outside Fresh-Air Connection...................................................................................................10
Exhaust and Intake Locations..................................................................................................10
Mobile Home Installation.........................................................................................................11
Corner Through Wall Installation..............................................................................................11
Horizontal Exhaust Through Wall Installation............................................................................12
Through Wall With Vertical Rise and Horizontal Termination Installation - Freestanding................13
Inside Vertical Installations......................................................................................................14
Outside Vertical Installations....................................................................................................14
Hearth Mount Installation........................................................................................................15
Exterior Mounted Exhaust Blower (20-070)...............................................................................16
Typical Through Wall With Exterior Blower Kit Installation - Horizontal Termination......................17
Typical Through Wall With Exterior Blower Kit Installation - Vertical Termination..........................18
Thermostat Installation............................................................................................................19
Optional Slider/Damper Installation..........................................................................................19
Slider/Damper Set-Up..............................................................................................................20
Optional Panel Kit....................................................................................................................21
Fan Kit Installation..................................................................................................................22
Troubleshooting............................................................................................................................23
Wiring Diagram.............................................................................................................................26
Parts List......................................................................................................................................27
Parts Diagram - Components..........................................................................................................29
Parts Diagram - Steel.....................................................................................................................30
Warranty......................................................................................................................................31
Installation Data Sheet..................................................................................................................34
2
Introduction
* This manual is designed for the technician in conjunction with the owner’s manual. *
Rating Label Location:
The rating label is located on the back of the ash pan door.
Safety Warnings And Recommendations:
Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet
Stove. Failure to follow these instructions may result in property damage, bodily injury or
even death. Any unauthorized modification of the appliance or use of replacement parts not
recommended by the manufacturer is prohibited.
Caution: Do not connect to any air distribution duct or system.
Do not burn garbage or flammable fluids such as gasoline, naptha or engine oil.
Unit hot while in operation. Keep children, pets, clothing and furniture away.
Contact may cause skin burns.
Warning: Parts of the appliance, especially the external surfaces, will be hot to touch when in operation
and due care will need to be taken. Never place wood, paper, furniture, drapes or other combustible
materials within 80cm (31½”) of the front of the unit, 20cm (7⅞”) from each side, and 10cm (4”) from
the back of the unit. Do not let children or pets touch it when it is hot.
To prevent the possibility of a fire, ensure that the appliance is properly installed by adhering to the
installation instructions. An ENVIRO dealer will be happy to assist you in obtaining information with
regards to your local building codes and installation restrictions.
FIRE EXTINGUISHER AND SMOKE DETECTION: All homes with a pellet burning stove should have
at least one fire extinguisher in a central location known to all in the household. Smoke detectors should
be installed and maintained in the room containing the stove when installing and operating a pellet
burning appliance. If it sounds the alarm, correct the cause but do not deactivate. You may choose to
relocate the smoke detection devise within the room; DO NOT REMOVE THE SMOKE DETECTOR FROM
THE ROOM.
CHIMNEY OR RUN AWAY FIRE: Call local fire department (or dial 911). Close the draft fully. Examine
the flue pipes, chimney, attic, and roof of the house, to see if any part has become hot enough to catch
fire. If necessary, spray with fire extinguisher or water from the garden hose. IMPORTANT: Do not
operate the stove again until you are certain the chimney and its lining have not been damaged.
FUEL: This pellet stove is designed and approved to only burn wood pellet fuel with up to 3% ash
content. Dirty fuel will adversely affect the operation and performance of the unit and may void the
warranty. Check with your dealer for fuel recommendations. DO NOT use this appliance as an incinerator. DO NOT use unsuitable and non recommended fuels,
including liquid fuels.
THE USE OF CORDWOOD IS PROHIBITED BY LAW.
FLAMMABLE LIQUIDS: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter
fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from
the heater while it is in use.
3
Introduction
SOOT: Operation of the stove with insufficient combustion air will result in the formation of soot which
will collect on the glass, the heat exchanger, the exhaust vent system, and may stain the outside of the
house. This is a dangerous situation and is inefficient. Frequently check your stove and adjust the slider/
damper as needed to ensure proper combustion. See: “Slider/Damper Setting”.
CLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This
will vary due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect
and clean the exhaust vent semi-annually or every two tons of pellets.
The appliance, flue gas connector and the chimney flue require regular cleaning. Check them for blockage
prior to re-lighting after a prolonged shut down period.
ASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container
of ashes should be on a non-combustible floor on the ground, well away from all combustible materials
pending final disposal. If the ashes are disposed of by burial in soil or otherwise locally dispensed, they
should be retained in the closed container until all cinders have been thoroughly cooled.
ELECTRICAL: The use of a surge protected power bar is recommended. The unit must be
grounded. The grounded electrical cord should be connected to a standard 110-120 volts, nominal
average 2.0 Amps (4.1 Amps peak), 60 hertz electrical outlet and also must be accessible. Ensure the
polarity to the outlet, the unit will be plugged into, is correct as incorrect polarity can affect the unit’s
operation. If this power cord should become damaged, a replacement power cord must be purchased
from a qualified ENVIRO dealer. Be careful that the electrical cord is not trapped under the appliance and
that it is clear of any hot surfaces or sharp edges. This unit’s maximum power requirement is 184 watts
(600 watts peak).
When installing the stove in a mobile home, it must be electrically grounded to the steel chassis of the
home and bolted to the floor. Make sure that the structural integrity of the home is maintained and all
construction meets local building codes.
GLASS: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove
with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO
dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is
hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner,
or take a damp paper towel and dip into the fly ash. This is a very mild abrasive and will not damage the
glass.
OPERATION: The door and ash drawer cover must be kept closed securely except during ignition,
refuelling and removal of residue material to prevent fume spillage and for proper and safe operation of
the pellet stove. Also ensure all gaskets on the door are checked and replaced when necessary.
IMPORTANT: The door and ash drawer cover must be kept closed except during ignition, refueling and
removal of residue material to prevent fume spillage.
CAUTION: When operating during adverse weather, if the unit exhibits dramatic changes in combustion
stop using the unit immediately.
KEEP ASH PAN FREE OF RAW FUEL. DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN.
A fire in the ash pan may occur.
4
Introduction
INSTALLATION: Contact your local building or fire official to obtain a permit and any information on
installation restrictions and inspection requirements for your area. All local regulations, including those
referring to national and European Standards need to be complied with when installing this appliance.
Be sure to maintain the structural integrity of your home when passing a vent through walls, ceilings, or
roofs. It is recommended that the unit be secured into its position in order to avoid any displacement. This
appliance must be installed on a floor with an adequate load bearing capacity. If an existing construction
doesn’t meet these prerequisite, suitable measures (e.g. load distributing plate) shall be taken to achieve
it.
DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT.
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
FRESH AIR: Outside Fresh Air connection is optional. Fresh Air must be connected to all units installed
in Mobile and “Air Tight Homes” (R2000) or where required by local codes.
Consider all large air moving devices when installing your unit and provide room air accordingly. NOTE:
Extractor fans when operating in the same room or space as the appliance, may cause problems. Limited
air for combustion may result in poor performance, smoking and other side effects of poor combustion.
The stove’s exhaust system works with negative combustion chamber pressure and a slightly positive
chimney pressure. It is very important to ensure that the exhaust system be sealed and airtight. The ash
pan and viewing door must be locked securely for proper and safe operation of the pellet stove.
Do not burn with insufficient combustion air. A periodic check is recommended to ensure proper
combustion air is admitted to the combustion chamber. Setting the proper combustion air is achieved by
adjusting the slider damper located on the left side of the stove.
Minor soot or creosote may accumulate when the stove is operated under incorrect conditions such as an
extremely rich burn (black tipped, lazy orange flames).
If you have any questions with regards to your stove or the above-mentioned information, please feel
free to contact your local dealer for further clarification and comments.
SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF
YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED
FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE. THEREFORE, SHERWOOD
INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).
SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
5
Installation
Deciding Where to Locate your Pellet Appliance:
1. Check clearances to combustibles.
2. Do not obtain combustion air from an attic, garage or any unventilated space.
Combustion air may be obtained from a ventilated crawlspace.
3. Do not install the stove in a bedroom.
4. You can vent the stove through an exterior wall behind the unit or connect it to
an existing masonry or metal wood stove chimney (must be lined if the chimney
is over 6” (15 cm) diameter, or over 28 inches² (180 cm²) cross sectional area).
An interior vent can be used with approved pipe passing through the ceiling
and roof.
5. Locate the stove in a large and open room that is centrally located in the house.
This will optimize heat circulation.
6. The power cord is 8 feet (2.43 m) long and may require a grounded extension
cord to reach the nearest electrical outlet.
Appliance Dimensions and Specifications:
15 1/4"
(386 mm)
Weight (with full hopper): 238 lb (108 Kg)
Hopper Capacity: up to 48 lb (21.8 Kg)
Voltage: 110 - 120 V
Max Current: 4.1 Amps
Consumption on High: 3.1 lb/hr (1.4 Kg/hr)*
Consumption on Low: 1.3 lb/hr (0.6 Kg/hr)*
(Note: Consumption will vary with the type of
fuel used.)
17 7/8"
(455 mm)
19"
(483 mm)
34 1/8"
(868 mm)
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
HEAT LEVEL
FEED RATE
TRIM
COMBUSTION
BLOWER TRIM
ROOM AIR
FAN ON/OFF
17 1/2"
(444 mm)
19 3/4"
(503 mm)
19 1/2"
(496 mm)
24 7/8"
(632 mm)
Figure 1: Dimensions of Mini.
6
ON/OFF
Installation
Removing Pellet Stove From Pallet and Installing Hearth Pad:
Tool Required:
●T-20 screwdriver
● 5/16” socket or flat head
screwdriver
Installation:
1. Slide a hearth pad tab
through each of the three
(3) slots on the hearth pad
so the slotted end is up and
Figure 3: Screw behind ash box.
secure in place with a T-20
screw through the pad into the tab (refer to Figure 2).
2. Open the ash pan cover from the right then lift the cover up and
out to unhook the hinges at the left.
3. Remove the cab sides.
Figure 2: Installing tabs into hearth
a) Ensure the screws behind the ash box (Figure 3) and the three
pad.
(3) on each side at the back (Figure 4) are loosened.
b) Remove knob and collar from slider rod.
c) Pull the cab sides straight out.
4. Using a 5/16” socket or flat head screwdriver, remove the three
(3) wood screws that are holding the bottom of the stove to the
pallet. There is one (1) screw behind each side panel and one (1)
at the back behind the back grill (refer to Figure 5).
5. Loosen the three (3) T-20 screws from the base of the unit (see
Figure 6).
6. Either lift the unit up and
place it into the hearth pad
or carefully place the unit
on its back; it can rest on
the pallet it was shipped
on (allow the pipes to fit
through an opening in the
pallet).
7. Align the three (3) tabs on
the hearth pad to the three Figure 4: Screws at the back of the
cabinet side.
(3) screws on the unit (see
Figure 6), slide
together,
and
tighten the T-20
screws.
8. Adjust the leveling
legs to level and
support stove.
9. Re-install the cab
sides and ash pan
Figure 5: Screws to take out to remove
cover.
Figure 6: Mini Bern Hearth Pad in Place.
stove from pallet.
7
Installation
Clearances to Combustibles:
IMPORTANT: Attach the Mini’s Hearth Pad when installing the unit on a combustible floor. The supplied
hearth pad meet all the requirement of a proper hearth pad. If you do not use the supplied hearth pad a
hearth pad must be used when on combustible material.
If the Mini is installed on carpet the use of a solid material must be used under leveling legs.
Back Wall
4" (10cm)
ce
nt
al
W
Side Wall
ja
Ad
8"
(20cm)
3"
(7.5cm)
l
These dimensions are minimum clearances but
it is recommended that you ensure sufficient
room for servicing, routine cleaning and
maintenance.
Side wall to unit 8 inches (20 cm)
Back wall to unit 4 inches (10 cm)
Corner to unit
3 inches (7.5 cm)
Figure 7: Mini Clearance to Combustibles.
Alcove Clearances:
36"
(91.5cm)
This unit may be installed in an alcove. Maintain these
clearances to combustibles.
Minimum Alcove width 36 inches (91.5 cm)
Minimum Alcove height 48 inches (122 cm)
Maximum Alcove depth 30 inches (76 cm)
30"
(76cm)
48"
(122cm)
Install vent at clearances specified by the
vent manufacturer.
Figure 8: Mini Minimum Alcove Size.
8
Installation
Vent Termination Requirements:
IT IS RECOMMENDED THAT YOUR PELLET STOVE BE INSTALLED BY AN AUTHORIZED DEALER/INSTALLER.
Table 1: Use in conjunction with Figure 9 for allowable exterior vent termination locations.
Letter
Minimum Clearance
A
24 in (61 cm)
B
48 in (122 cm)
Beside/below any door or window that may be opened. (18” (46 cm) if outside
fresh air installed.)
C
12 in (30 cm)
Above any door or window that may be opened. (9” (23 cm) if outside fresh air
installed.)
D
24 in (61 cm)
To any adjacent building, fences and protruding parts of the structure.
E
24 in (61 cm)
Below any eave or roof overhang
F
12 in (30 cm)
To outside corner.
G
12 in (30 cm)
To inside corner, combustible wall (vertical and horizontal terminations).
H
3 ft (91 cm) within a height
of 15 ft (4.5 m) above the
meter/regulator assembly
I
3 ft (91 cm)
J
12 in (30 cm)
Clearance to non-mechanical air supply inlet to building, or the combustion air
inlet to any appliance.
K
24 in (61 cm)
Clearance above roof line for vertical terminations.
L
7 ft (2.13 m)
Clearance above paved sidewalk or paved driveway located on public property.
1. Do not terminate the
vent in any enclosed or
semi-enclosed areas such
as a carport, garage,
attic, crawlspace, narrow
walkway, closely fenced
area, under a sundeck
or porch, or any location
that can build up a
concentration of fumes
such as stairwells, covered
breezeway, etc.
Description
Above grass, top of plants, wood, or any other combustible materials.
To each side of center line extended above natural gas or propane meter/
regulator assembly or mechanical vent.
From any forced air intake of other appliance
G
K
E
D
F
B
Opens
G
Opens
B
A
Termination Cap
Air Supply Inlet
G
C
I
G Gas Meter
Opens
Restriction Zone
L
H
(Termination not allowed)
Figure 9: Use in conjunction with Table 1 for allowable exterior vent termination
locations.
2. Vent surfaces can become
hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.
3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe be
installed outside when the appliance is vented directly through a wall, to create some natural draft to prevent the
possibility of smoke or odor during appliance shut down or power failure. This will keep exhaust from causing a
nuisance or hazard from exposing people or shrubs to high temperatures. In any case, the safest and preferred
venting method is to extend the vent through the roof vertically.
4. Distance from the bottom of the termination and grade is 12” (30 cm) minimum. This is conditional upon the
plants and nature of grade surface. The exhaust gases are hot enough to ignite grass, plants and shrubs located
in the vicinity of termination. The grade surface must not be lawn.
5. If the unit is incorrectly vented or the air to fuel mixture is out of balance, a slight discoloration of the exterior
of the house might occur. Since these factors are beyond the control of Sherwood Industries Ltd, we grant no
guarantee against such incidents.
NOTE: Venting terminals shall not be recessed into walls or siding.
9
Installation
Outside Fresh-Air Connection:
Outside fresh air is mandatory when installing
this unit in airtight homes and mobile homes.
A Fresh-air intake is strongly recommended for
all installations. Failure to install intake air may result
in improper combustion as well as the unit smoking
during power failures.
When connecting to an outside fresh air source, do not
use plastic or combustible pipe. A 2” minimum (51
mm) ID (inside diameter) steel, aluminum or copper
pipe should be used. It is recommended, when you
are installing a fresh air system, to keep the number of
bends in the pipe to a minimum.
Outside
Wall
2" ID
(51 mm)
Optional
Elbow
Figure 10: Outside Air Connection.
Exhaust and Intake Locations:
EXHAUST
Base of unit to center of flue
Center of unit to center of flue
10¼” (255 mm)
0”
(0 mm)
[at center of unit]
FRESH AIR INTAKE.
Base of unit to center of intake 6⅜” (162 mm)
Center of unit to center of intake 21/16” (53 mm)
101/4"
(260mm)
63/8"
(162mm)
21/16"
(53mm)
Figure 11: Mini Inlet and Outlet Location.
10
Installation
Mobile Home Installation:
● Secure the heater to the floor using the
two holes in the pedestal.
● Ensure the unit is electrically
grounded to the chassis of your home
(permanently).
● Do not install in a room people sleep
in.
● Outside fresh air is mandatory. Secure
outside air connections directly to
fresh air intake pipe and secure with
three (3) screws evenly spaced.
CAUTION: THE STRUCTURAL
INTEGRITY OF THE
MANUFACTURED HOME FLOOR,
WALL AND CEILING/ROOF MUST
BE MAINTAINED.
ENVIRO Mini
Optional
Hearth Pad
Flooring
Steel Frame
1/4” Lag Bolts
Securely Fastened
Ground Wire Directly
to Metal Chassis
Figure 12: Mobile home installation.
Corner Through Wall Installation:
3" (75mm)
Wall thimble
manufactured
by pellet vent
manufacturer.
3"
(75mm)
Figure 13: Corner Installation.
11
Installation
Horizontal Exhaust Through Wall Installation:
Vent installation: install vent at clearances specified by the vent manufacturer.
A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces,
or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and
Equipment. Only use venting of L or PL type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm).
1. Choose a location for your stove that meets
the requirements stated in this manual and
Wall
allows installation with the least amount of
thimble
4"
interference to house framing, plumbing,
(10 cm)
12"
wiring, etc.
(30.5 cm)
2. Install a non-combustible hearth pad
(where necessary).
3. Place the appliance 15” (37.5 cm) away
from the wall. If the stove is to be set on
a hearth pad, set the unit on it, and adjust
6"
the leveling legs.
(15 cm)
4. Locate the center of the exhaust pipe on
the stove. Extend that line to the wall.
45°
elbow
Once you have located the center point on
the wall, refer to pellet vent manufacturer
installation instructions for correct hole
Existing floor
Non-combustible
size and clearance to combustibles.
(combustible)
floor protection.
5. Install the wall thimble as per the
Figure 14: Straight through wall Installation.
instructions written on the thimble.
Maintain an effective vapour
barrier in accordance with
local building codes.
6. Install a length of 3” (75
mm) or 4” (100 mm) vent
pipe into the wall thimble.
The pipe should install easily
Exhaust Tube
into the thimble.
3" (75mm) or 4" (100mm) "PL" or "L" vent
7. Connect
the
exhaust
vent pipe to the exhaust
Wall Thimble
pipe on the stove. Seal
the connection with high
temperature silicone.
8. Push the stove straight back,
45° Elbow with screen or
Termination Cap
leaving a minimum of 4” (10
Fresh Air Intake Tube
cm) clearance from the back
of the stove to the wall. Seal
the vent pipe to the thimble
with
high
temperature
High Temperature RTV
Silicone Required
silicone.
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
HEAT LEVEL
FEED RATE
TRIM
COMBUSTION
BLOWER TRIM
ROOM AIR
ON/OFF
FAN ON/OFF
AUGE
R
MODE
AUTO/O
HIGH/L FF
OW
MANUA
HEAT
L
LEVE
L
FEED
RATE
TRIM
ROOM
FAN
AIR
ON/O
FF
COMB
BLOW USTIO
ER
N
TRIM
ON/O
FF
Figure 15: Venting to use with straight through wall Installation.
12
Installation
9. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length
of pipe (PL type) to the outside of the home to connect to the first section. Do not forget to place
high temperature silicone around the pipe that passes through the thimble.
10. Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The
stainless steel cap termination manufactured by the vent manufacturer is recommended. However,
when the vent terminates several feet above ground level and there are no trees, plants, etc. within
several feet, a 45° elbow can be used as termination. The elbow must be turned down to prevent
rain from entering.
NOTE:
• It is recommended that horizontal through wall installations have 3 to 5 feet (91 to 152 cm) of vertical
pipe in the system to help naturally draft the unit in the event of extreme weather or a power outage.
• Some horizontal through wall installations may require a “T” and 3 to 5 feet (91 to 152 cm) of vertical
pipe outside the building to help draft the unit. This may be required if a proper burn cannot be
maintained, after the stove has been tested and the airflow set. This is due to the back pressure in the
exhaust caused by airflow around the structure.
• Follow vent manufacturer guidelines for installation of venting. High temp Sealent must be used when
connecting vent pipe to the unit’s starter pipe. Improper seals at the vent joints may cause combustion
by-products to leak into the room where installed - seal as required.
Through Wall With Vertical Rise and Horizontal Termination Installation - Freestanding:
A 45° elbow may be used in place of the termination cap (or stainless steel termination hood).
Figure 16 is the recommended installation set up.
Figure 17 is the installation to use if there is a concrete or retaining wall in line with exhaust vent on
a pellet stove. The termination must be 12” (30 cm) from the outside wall and 12” (30 cm) above the
ground.
Horizontal frame
for thimble
Termination cap
90° elbow
Wall framing
90° elbow
Vertical section of vent pipe
Horizontal frame for thimble
Termination cap
Wall thimble
Vertical section
of vent pipe
Wall framing
Wall strap
Concrete Wall
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
HEAT LEVEL
FEED RATE
TRIM
COMBUSTION
BLOWER TRIM
ROOM AIR
FAN ON/OFF
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
HEAT LEVEL
ON/OFF
Clean out tee
FEED RATE
TRIM
COMBUSTION
BLOWER TRIM
ROOM AIR
FAN ON/OFF
ON/OFF
Clean out tee
Wall thimble
Figure 16: Venting horizontally with rise.
Figure 17: Venting with concrete wall behind unit .
13
Installation
Inside Vertical Installations:
Rain Cap (ensure cap is
at least 3ft above the
roof at the lowest point)
2 ft
(600 mm)
Roof Flashing
Roof Rafter
Fire Stop with
Support Collar
Ceiling Joist
Vertical Vent Pipe
Clean Out Tee with
Pipe Adapter
NOTE: All vent sections must
maintain 3 inches (7.5 cm)
clearances to combustibles.
Figure 18: Inside Vertical Installation.
1. Choose a stove location that is ideal. See the
section “Deciding Where to Locate your Pellet
Appliance.”
2. Place a non-combustible hearth pad where
necessary.
3. Place the unit on the hearth pad (if installed
on a combustible surface) and space the
unit in a manner so when the pellet vent is
installed vertically, it will be 3” (7.5 cm) away
from a combustible wall.
4. Install the tee with clean out.
5. Install the pellet vent upward from there.
When you reach the ceiling, make sure
that the vent goes through the ceiling fire
stop. Maintain a 3” (7.5 cm) distance to
combustibles and keep attic insulation away
from the vent pipe. Maintain an effective
vapor barrier.
6. Finally, extend the pellet vent to go through
the roof flashing.
7. Ensure that the rain cap is approximately 24”
(600 mm) above the roof.
Outside Vertical Installations:
Rain cap
To accomplish a outside vertical pipe installation,
follow steps 1 through 5 in the “Inside Vertical
Installations - Freestanding” section and then finish it
by performing the following (refer to Figure 16).
Flashing
24"
(61 cm)
1. Install a tee with clean out on the outside of the
house.
2. Install PL vent upward from the tee. Make sure
that you install support brackets to keep the vent
straight and secure.
3. Install ceiling thimble and secure the flashing as
you go through the roof.
4. Ensure that the rain cap is approximately 24”
(600 mm) above the roof.
4"
(10 cm)
3" (7.5 cm)
Clearance
Support
bracket
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
HEAT LEVEL
FEED RATE
TRIM
COMBUSTION
BLOWER TRIM
ROOM AIR
FAN ON/OFF
ON/OFF
Tee with
cleanout
Type "PL"
vent
Figure 19: Outside Vertical Installation.
14
Rain Cap
Steel Plate or Flashing
Installation
Flexible or
Rigid 6" Stainless
Steel Liner
Hearth Mount Installation:
Damper Removed
or Fastened Open
10" (25.4 cm) Mantel
Minimum 8" (20 cm)
from top of stove
Flue
Connector
Clean-out tee
Min 6" (150 mm)
Optional Hearth
or Other
Floor Protection
Masonry Fireplace
Refer to Figures 20 and 21.
1.Install the hearth pad.
2.Lock the fireplace damper in the open
position.
3.Install a positive flue connector at the
fireplace dampers or seal the chimney at
the top.
4.Connect a tee to the exhaust pipe.
5.Install flexible stainless steel liner or listed
pellet vent to the top of the chimney.
Combustible Floor
Figure 20: Freestanding hearth mount installation.
Rain cap
Storm collar
Seal plate (cover plate)
Existing masonry flue
Vent pipe (single wall
stainless flex pipe or
solid PL vent)
Flexible vent connector
(use this 5 foot [152cm]
section of pipe to vent
past fireplace damper
or small shelf)
Fireplace damper
location
Clean out tee
Existing fireplace
AUGER
MODE
AUTO/OFF
HIGH/LOW
MANUAL
RATE
FEED
TRIM
TION
LEVEL
HEAT
COMBUS TRIM
BLOWER
ON/OFF
AIR
ROOM
ON/OFF
FAN
Figure 21: Freestanding hearth mount installation overview.
15
Installation
Exterior Mounted Exhaust Blower (20-070):
The Mini can be equipped with an externally mounted exhaust blower. This optional kit includes all
components necessary to install the exhaust blower on any vertical wall surface.
Choose a location for your stove that meets the requirements
stated in your manual and allows installation with the least
amount of interference with house framing, plumbing,
wiring, etc.
Included in the Exterior Mounted Exhaust Blower Kit are:
1 - Exhaust blower housing box.
1 - Blower cover plate.
1 - Hardware bag
Figure 22: Exterior Blower Kit.
1. Remove the left hand cabinet side by removing the two
(2) screws down the front. Loosen the three screws on
the back of the cabinet side and remove panel.
2. Loosen the six (6) screws that hold the back grill in place.
Lift the back grill off the screws.
3. Disconnect the Exhaust blower wires from the wire
harness. Remove the exhaust blower motor from the
housing; six (6) screws. Cover hole in housing with cover
plate provided (see Figure 23).
Figure 23: Exterior Blower Kit.
4. Remove the cover from the exhaust blower housing box.
5. Install the exhaust blower housing box into the pipe placed
through the wall thimble, seal with high temperature
silicone. Fasten the box to the wall with (4) four screws,
seal edges of box to wall with clear silicone.
6. Drill a hole through the wall thimble plate for the electrical
wires. Pass the armored cable through the wall thimble.
Use the strain relief provided. Do not pass cable
through vent hole.
7. Install the Exhaust Blower motor into the external exhaust
blower housing box. Make the electrical connections to
the wire harness and exhaust blower.
8. Replace the cover on the Exhaust Box and the back grill of
the stove and ensure the screws are tightened down.
Figure 24: Exterior Blower Kit cut-through.
16
9. Install vertical pipe as instructed in appropriate section.
Installation
Typical Through Wall With Exterior Blower Kit Installation - Horizontal Termination:
90° Elbow
45°Elbow with Rodent
screen or stainless
steel termination hood
2ft (610mm) Riser
Pipe Adaptor
Exterior Blower
and Housing
Electrical Cable
Figure 25: Through Wall Installation with Exterior Blower Kit.
NOTE:
Ensure that all interior vent connections are sealed by placing a small bead of high temperature silicone
around each chimney connection.
Also ensure that all vertical vent sections are properly supported and that all clearances to combustibles
are maintained in accordance with the vent manufacturer’s specifications.
Wall Strap
To supply power to
the exhaust blower
Figure 26: Through Wall Installation with Exterior Blower Kit; Side View.
Install the amour coated electrical cable from the exhaust blower housing, through the wall thimble plate
and attach to the pre drilled hole in the left hand rear hopper pillar. Hook up to wires from the exhaust
blower wiring harness.
All electrical connections must be in accordance to local code requirements
17
Installation
Typical Through Wall With Exterior Blower Kit Installation - Vertical Termination:
Roof Sheathing
Rain Cap
Roof Flashing
Roof Rafters
Follow the previous pages for through wall
installations. Ensure that vent pipe is properly
secured to wall using wall straps. Maintain
clearances to combustibles on vent pipe as
well as unit.
Ceiling Joists
Vent Pipe
Exterior Wall
Sheathing
Outside Vent
Termination
Figure 27: Through Wall Installation with Exterior Blower Kit;
Vertical Termination.
Thermostat Installation:
1. Install the wall thermostat in a location that is not to close too the unit but will effectively heat the
desired area.
2. Install a 12 or 24 Volt Thermostat using an 18 x 2 gauge wire from the unit to the thermostat.
Remove jumper
wire and install
thermostat wires here.
Figure 28: Thermostat wire placement.
18
If the unit has been placed in the HI / LOW mode,
the unit will be taken to a low or idle setting when the
thermostat is not calling for heat. When the thermostat
calls for heat, the unit will go to the setting that is
displayed on the control board Heat Indicator.
Installation
Slider/Damper Set-Up:
This is used to regulate the airflow through the pellet
stove. The slider damper should be initially set by a
trained technician using magnehelic.
The slider damper knob is located on the left side of the stove.
The combustion exhaust blower is a variable speed blower
controlled by the heat output button. This blower will decrease
the vacuum pressure inside the stove and as the heat output
button is turned down. The vacuum pressure inside the firebox
will increase as the combustion exhaust blower increases in
speed (higher heat output setting).
If, after long periods of burning, the fire builds up and overflows
the burn pot or there is a build up of clinkers, this would be a
sign that the pellet quality is poor, this requires more primary air,
the slider damper must be pulled out to compensate. Pulling the
slider damper out gives the fire more air.
Figure 29: Slider/Damper Knob.
The easiest way to make sure that an efficient flame is achieved
is to understand the characteristics of the fire.
• A tall, lazy flame with dark orange tips requires more air
– Open slider (pull out) slightly.
• A short, brisk flame, like a blowtorch, has too much air
– Close slider (push in) slightly.
• If the flame is in the middle of these two characteristics
with a bright yellow/orange, active flame with no black tips
then the air is set for proper operation (see Figure 30).
SPECIAL NOTES:
Pellet quality is a major factor in how the Pellet stove will operate.
If the pellets have a high moisture content or ash content the
fire will be less efficient and has a higher possibility of the fire
building up and creating clinkers (hard ash build-up).
Figure 30: Efficient Flame.
IMPORTANT: Taking a reading of vacuum pressure inside the firebox with a magnehelic gauge should
be used to set the slider for best combustion. The slider damper should be set only on a hot stove
(operating for thirty (30) minutes or more) by using a Magnahelic Pressure Gauge to measuring the
pressure in the firebox. The best settings are a reading of approximately 0.11 0.12 inches of
water column (27.4 - 29.9 Pa) on the high fire setting. Some fuels may require higher or
lower settings. The reading can be taken from the ⅛” (3 mm) hole located on the front of the unit
below the ash shelf.
19
Troubleshooting
DO NOT:
● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard
if handled improperly. Only qualified technicians should deal with possible internal electrical failures.
● Do not remove from the firebox any screws without penetrating oil lubrication.
WHAT TO DO IF:
1. The stove will not start.
2. The stove will not operate when hot.
3. The exhaust blower will not function normally.
4. Light # 2 on Heat output bar flashing.
5. Auger light flashes but auger motor does not turn at all
6. Light # 4 on Heat output bar flashing. 7. The convection blower will not function normally.
8. Igniter- the pellets will not light.
9. Control settings (Heat Level) has no effect on the fire.
10. The stove keeps going out.
*NOTE: All troubleshooting procedures should be carried out by qualified technicians or
installers.
1. The stove will not start.
Make sure the stove is plugged in and the wall outlet is supplying power..
If the Control Board has been placed in the ON /OFF thermostat mode, then turn the thermostat up to
call for heat.
Check the Heat Level Indicator. - If the # 2 light is flashing (see the # 2 light is flashing)
Check the fuse on the circuit board.
If the unit still does not start, contact your local service dealer for service.
2. The stove will not operate when hot.
Check the Heat Level Indicator if a fire is not detected, or if the fire has gone out the #3 light will
flash because the Exhaust Temperature Sensor’s contacts have opened.
Check the hopper for fuel.
Incorrect air damper setting. - Excessive air may consume the fire too quickly before the next drop of
fuel, leaving completely unburned fuel in the burn pot liner. - Insufficient air will cause build up, further
restricting the air flow through the Burn Pot Liner. This in turn will cause the fuel to burn cold and very
slowly. Fuel may build up and smother the fire. In this case clean the burn pot. (NOTE: unit may
require a change to the vent system or installation of fresh air to correct Air to Fuel ratio
problems).
Combustion Blower failure. - The Combustion Blower is not turning fast enough to generate the proper
vacuum in the fire box. Visual Check – is the blower motor turning.
Check the Exhaust Blower voltage across the blower wires (>=114V on #5 setting and >= 82V on #1
setting). – Replace the Circuit Board if the Voltage reading is less than 82 V. with a line voltage >114
V AC.
Check Vacuum levels in the exhaust channel by bypassing the Vacuum Switch, then remove the Vacuum
hose from Vacuum Switch. Check exhaust vacuum readings by placing the open end of the Vacuum
Hose on a Magnahelic Gauge (readings must be above .10” W.C. on low fire).
If the motor fails to reach a 0.10” W.C. readings, then replace the Combustion Blower.
20
Troubleshooting
Poor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning
or operational.
Exhaust Temperature Sensor failure. – Bypass sensor located on Exhaust Blower if stove now operates
properly, the unit may require cleaning or a new sensor. Contact your local dealer for service.
Check the fuse on the circuit board.
3. The exhaust motor will not function normally.
Open the left side access panel; check all connections against the wiring diagram.
See “2. The stove will not operate when hot.” section.
4. Light # 2 on Heat output bar flashing.
(The Vacuum Switch contacts have opened for more than 15 sec.)
Pinch, break or blockage in Vacuum Hose - Check hose for pinch points or damage, replace or re-route
as required. Blow out Vacuum Hose
Blocked Hose Barb on Exhaust Channel - Use a paper clip to clean out Hose Barb or remove the Vacuum
Hose from the Vacuum Switch and blow into the hose to remove blockage.
Blocked exhaust / venting system - Have stove and venting cleaned and inspected.
Severe negative pressure in area where unit is installed - Check the operation by opening a window,
does this solve the problem? If it does, install fresh air intake to unit or room. Venting system may
require vertical section to move termination into a low pressure zone.
Vacuum Switch failure - Bypass the vacuum switch, if this corrects the problem check for above
problems before replacing the Vacuum Switch.
Damage to gray wires between Circuit Board and Vacuum Switch - Inspect wires and connectors
Combustion Blower failure - The Combustion Blower is not turning fast enough to generate the proper
vacuum in the Exhaust Channel. Visual Check; is the blower motor turning? Check the Exhaust Blower
voltage across the blower wires (>=114V on #5 setting and >= 82V on #1 setting). – Replace the
Circuit Board if the Voltage reading is less than 82 V. with a line voltage >114 V AC.
Check Vacuum levels in the exhaust channel by bypassing the vacuum switch, then remove the Vacuum
hose from Vacuum Switch. Check exhaust vacuum readings by placing the open end of the Vacuum
Hose on a Magnahelic Gauge. (readings must be above .10” W.C. on low fire).
If the motor fails to reach a 0.10” W.C. readings, then replace the Combustion Blower
To reset Circuit Board after a trouble code - push the ON/OFF button
5. Auger light flashes but auger motor does not turn at all.
If the Auger gear box does not turn but the motor’s armature does try to spin then the auger is jammed.
– Try to break apart jam by poking at the jam through the drop tube. If this fails then empty the hopper
and remove the Auger Cover **Remember to re-seal the cover after installation**
Check the fuse on the circuit board.
6. Light # 4 on Heat output bar flashing. Reset high limit sensor and determine cause – was it Convection Blower failure?
21
Troubleshooting
7. The convection blower will not function normally.
Clean all grill openings at the back and below unit .
Press the fan button; does the fan come on? Press again to verify that the blower turns on; if, not
contact your local dealer for service.
8. Ignitor- the pellets will not light.
Everything else in the stove operates but the ignitor will not light the pellets.
Make sure the burn pot liner is up tight and square to the ignitor tube by pushing the burn pot back
against the ignitor tube.
Check to see if the exhaust blower is operating. If not, contact your local dealer for service.
Check the fuse on the circuit board.
NOTE: The ignitor should be bright orange in color. If not replace the ignitor.
9. Control settings (Heat Level) has no effect on the fire.
NOTE: If the system light is flashing the Control Board has complete control of the unit. When the units
system light becomes solid then control of the unit is given back to the operator.
If there is no control of the Heat Level button make sure the thermostat is calling for heat.
Call your local dealer for service.
10. The stove keeps going out.
If the stove goes out and leaves fresh unburned pellets or cigarette-like ashes in the burn pot liner, the
fire is going out before the stove shuts off.
Check to see that the Slider / Damper is in the correct position (set with a magnehelic gauge).
Turn the Heat Level up slightly (poor quality pellets will require slightly higher settings).
If the stove goes out and there are partially burned pellets left in the burn pot liner, the stove has shut
down due to a lack of air, exhaust temperature, or power failure.
Adjust the Slider / Damper.
Adjust the trim settings
Check to see if the stove needs a more complete cleaning.
Turn the Heat Level up slightly (poor quality pellets will require slightly higher settings).
Did the power go out?
Contact your local Dealer for service.
22
Wiring Diagram
Armor Cable Supplied
Optional Exterior
Exhaust Blower
Grey
Grey
Black
Combustion
Blower
Vacuum
Switch
White
White
Blue
Brown
Exhaust
Temperature
Sensor
Power
Cord
Brown
Ground
Thermostat
5 Amp
Fuse
Black
White
Orange
Orange
Purple
Blue
Yellow
Red
Grey
Grey
Brown
Brown
Red
Red
115V
White
220V
Blue
115V
Black
220V
Brown
Connect
Thermostat
Here
Hot
Red
White
Black
Black
Common
Ignitor
Purple
White
Yellow
White
Orange
Orange
Convection
Blower
Auger
Motor
High Limit
Temperature
Sensor
23
Parts List
Reference
Number
Part Number
1
120°F (49°C) Ceramic Fan Temperature Sensor
EC-001
2
Auger Motor - 115V
EF-001
3
High Limit Temp Sensor 200°F (93°C) Manual Reset
EF-016
4
Vacuum Switch - 115V
EF-017
Silicone Hose
EF-018
Aluminum Hose Barb
EF-019
Shoulder Bolt, Hardened Bushing & Nut (Set of 2)
EF-124
Combustion Blower motor with mount
EF-161
Ash Pan Latch
EF-178
5
6
7
8
9
24
Description
Auger Brass Bushings (Set of 2)
EF4i-065
Door Hinge Bracket
EF5-135
External Exhaust Back (For Optional Kit)
EF5-143
External Exhaust Box
EF5-144
(For Optioal Kit)
External Exhaust Bottom (For Optioal Kit)
EF5-145
Domestic Power Cord - 115V
EC-042
Hardened Bushing
20-020
External Exhaust Kit (3”)
20-070
400 Watt Ignitor - 115V
50-619
Circuit Board 5 Amp Fuse - 115V (Pair)
50-833
Exhaust Blower Assembly - 115V
50-901
5/8”
50-968
ID Auger Collar with Screw
10
Heat Exchanger Rod
50-1154
11
Glass with Gasket (356mm x 244mm)
50-1155
12
Slider Damper Rod & Knob
50-1156
Wire Harness
50-1157
13
Latch Assembly
50-1158
14
Door Handle
50-1159
Parts List
Reference
Number
Description
Part Number
15
Auger
50-1161
16
Firebox Panel Set with Insulation
50-1162
17
Front Louvers
50-1169
18
Lid Set
50-1171
19
Stove Top Assembly
50-1172
Hopper Guard
50-1174
20
Handle Bracket
50-1177
21
Draft Slider
50-1178
22
Ash Pan Cover
50-1180
23
Ash Pan
50-1181
24
Ash Shelf Louver
50-1182
25
Starter Pipe 3”
50-1185
26
60mm Tangential Blower Mini - 115V
50-1217
27
Mini Hearth Pad
50-1219
Burner Scraper Tool
50-1254
28
Leveling Legs (Set of 4)
50-1296
29
Back Grill
50-1297
30
Burn Pot
50-1166
31
Burn Pot Liner
50-1167
32
Door Assembly Complete
50-1179
33
Cabinet Side Left
50-1183
34
Cabinet Side Right
50-1271
Mini Domestic Owners Manual
50-1220
Mini Domestic Technical Manual
50-1221
35
Circuit Board DHC 4100 - 115V
50-1477
36
Control Panel Decal
50-1476
37
Control Panel and Decal
50-1478
25
Parts Diagram - Components
11
10
3
15
26
12
9
1
35
14
12
8
36
7
AU
GE
R
MO
DE
AU
TO
/OF
HIG
F
H/L
OW
MA
NU
AL
HE
AT
LE
VE
L
FE
ED
TRRA
IM TE
RO
FA OM
N
ON AIR
/O
FF
4
CO
BL MB
OW US
ER TIO
TR N
IM
ON
/O
FF
37
Mini - Components
September 2008
26
2
28
33
25
29
21
6
19
23
5
18
22
20
24
34
27
30
31
32
September 2008
16
Mini - Steel Components
19
Parts Diagram - Steel
27
Warranty
Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood
Industries, our commitment to the highest level of quality and customer service is the most important
thing we do. Each Enviro stove is built on a tradition of using only the finest materials and is backed by
our Exclusive Lifetime Limited Warranty to the original purchaser. With Enviro, you’re not just buying a
stove, you’re buying a company with years of unequalled performance and quality.
Limited Lifetime Warranty:
Under this warranty, Sherwood Industries Ltd. covers the fireplace or stove body and accessories
against defects in materials and workmanship, for part repair or replacement for the first seven (7)
years and limited labour for the first two (2) years to the original purchaser. This Warranty covers:
Firebox, Heat Exchanger, Burn Pot, Ceramic Glass, Pedestals, Panels, Legs, and Door Assembly. Please
see the exclusions and limitation section below as certain restrictions and exclusions apply to this
warranty.
Limited Three (3) Year Warranty
Under this warranty, Sherwood Industries Ltd. covers the Burn Pot Liner and Log Sets against defects
in materials and workmanship, for part repair or replacement for the first three (3) years and limited
labour for the first two (2) years to the original purchaser. Please see the exclusions and limitation
section below as certain restrictions and exclusions apply to this warranty.
Limited Two (2) Year Warranty:
Under this warranty, Sherwood Industries Ltd. covers: Ignitor, Auger Motor, Circuit Board, Timers,
Temp Sensors, Blowers, Vacuum Switch, Firebox Panels, and Wire Harness, against defects in materials
and workmanship, for part repair or replacement for the first two (2) years and limited labour for the
first two (2) years to the original purchaser. Please see the exclusions and limitation section below as
certain restrictions and exclusions apply to this warranty.
Limited One (1) Year Warranty:
Under this warranty, Sherwood Industries Ltd. covers all exterior surface finishes against defects in
materials and workmanship, for part repair or replacement and limited labour for the first (1) year to
the original purchaser. Please see the exclusions and limitation section below as certain restrictions and
exclusions apply to this warranty.
Here is how our Warranty works
If you have any concerns with your Enviro product please contact the dealer where you purchased the
fireplace or stove. Your dealer shall make all claims under this warranty in writing.
To the Dealer
When filling out a warranty claim please complete the following information on an official warranty claim
form:
Customer information: Name, address and telephone number of purchaser and date of purchase.
Dealer information: Date of installation, name of installer and dealer, serial number of the appliance,
nature of complaint, defects or malfunction, description and part numbers of any parts replaced.
To the Distributor
Sign and verify that work and information are correct.
28
Warranty
Exclusions and Limitations:
1. This Warranty does not cover tarnish, discoloration or wear on the plating or paint.
2. This Warranty excludes wear and tear or breakage caused by cleaning, moving or service on log set.
3. A qualified installer must install this stove or fireplace. This Limited Warranty covers defects in materials
and workmanship only if the product has been installed in accordance with local building and fire codes;
in their absence, refer to the owner’s manual. If the product is damaged or broken as a result of any
alteration, willful abuse, mishandling, accident, neglect, or misuse of the product, the Limited Warranty
does not apply.
4. The stove must be operated and maintained at all times in accordance with the instructions in the
Owner’s Manual. If the unit shows signs of neglect or misuse, it is not covered under the terms of this
Warranty policy. Performance problems due to operator error will not be covered by the Limited Warranty
policy.
5. As this is a heating appliance some changes in colour of surface finishes may occur. This is not a flaw
and as such is not covered under this warranty.
6. Some minor expansion, contraction, or movement of certain parts and resulting noise, is normal and not
a defect and, therefore, is not covered under this Limited Warranty.
7. Misuse includes over-firing. Over-firing this appliance can cause serious damage and will nullify the
Limited Warranty.
8. The Limited Warranty will cover glass thermal breakage only and will not cover misuse of the stove glass,
including but not limited to glass that is struck, has surface contaminates or has had harsh or abrasive
cleaners used on it.
9. This warranty does not cover products made or provided by other manufacturers and used in conjunction
with the operation of this stove without prior authorization from Sherwood Industries Ltd. The use of
such products may nullify the Limited Warranty on this stove. If unsure as to the extent of this Limited
Warranty, contact your authorized Enviro dealer before installation.
10. Sherwood Industries Ltd. will not be responsible for inadequate performance caused by environmental
conditions.
11. The Limited Warranty does not cover installation and operational related problems such as spillage
caused by environmental conditions. Environmental conditions include but are not limited to nearby
trees, buildings, roof tops, wind, hills, mountains, inadequate venting or ventilation, excessive offsets,
negative air pressures or other influences caused by mechanical systems such as furnaces, fans, clothes
dryers etc.
12. The Limited Warranty is void if:
a) The stove has been operated in atmospheres contaminated by chlorine, fluorine or other damaging
chemicals.
b) The stove is subject to submersion in water or prolonged periods of dampness or condensation.
c) Any damage to the unit, combustion chamber or other components due to water, or weather damage
which is the result of, but not limited to, improper chimney/venting installation.
c) Salt air in coastal areas or high humidity can be corrosive to the finish; these environments can cause
rusting. Damage caused by salt air or high humidity is not covered by the Limited Warranty.
13. Exclusions to the Limited Warranty include: injury, loss of use, damage, failure to function due to
accident, negligence, misuse, improper installation, alteration or adjustment of the manufacturer’s
settings of components, lack of proper and regular maintenance, alteration, or act of God.
14. The Limited Warranty does not cover damage caused to the fireplace or stove while in transit. If this
occurs, do not operate the stove and contact your courier and/or dealer.
15. The Limited Warranty does not extend to or include firebox paint, door or glass gaskets with damage
caused by normal wear and tear, or exterior paint discoloration or chipping, worn gaskets, etc.
16. The Limited Warranty does not include damage to the unit caused by abuse, improper installation, or
modification of the unit.
29
Warranty
17. Damage to plated surfaces caused by fingerprints, scratches, melted items, or other external scores and
residues left on the plated surfaces from the use of abrasive cleaners or polishes is not covered in this
warranty.
18. The Limited Warranty does not cover tarnish, discoloration or wear on the plated surfaces.
19. The paint on the Metal Brick Liner may peel. This is due to the extreme conditions applied to the paint
during normal usage. It is not a flaw and is not covered under warranty.
20. Sherwood Industries Ltd. is free of liability for any damages caused by the fireplace or stove, as well as
inconvenience expenses and materials. The Limited Warranty does not cover incidental or consequential
damages.
21. The Limited Warranty does not cover any loss or damage incurred by the use or removal of any
component or apparatus to or from the Enviro fireplace or stove without the express written permission
of Sherwood Industries Ltd. and bearing a Sherwood Industries Ltd. label of approval.
22. Any statement or representation of Enviro products and their performance contained in Enviro
advertising, packaging literature, or printed material is not part of the Limited Warranty.
23. The Limited Warranty is automatically voided if the fireplace or stove’s serial number has been removed
or altered in any way. If the stove is used for commercial purposes, it is excluded from the Limited
Warranty.
24. No dealer, distributor, or similar person has the authority to represent or warrant Enviro products beyond
the terms contained within the Limited Warranty. Sherwood Industries Ltd. assumes no liability for such
warranties or representations.
25. Sherwood Industries Ltd. will not cover the cost of the removal or re-installation of the stove, hearth,
facing, mantels, venting or other components.
26. Labour to replace or repair items under this Limited Warranty will be covered per our warranty service
fee reimbursement schedule. Labour rates are set per component and as such total labour costs may
not be covered.
27. Sherwood Industries Ltd. is not liable for freight or labour on any stove replaced in-field and is not liable
for travel costs for service work. In the event of in-home repair work, the customer will pay any inhome travel fees or service charges required by the Authorized Dealer.
28. At no time will Sherwood Industries Ltd. be liable for any consequential damages which exceed the
purchase price of the unit. Sherwood Industries Ltd. has no obligation to enhance or modify any
stove once manufactured (example: as a stove evolves, field modifications or upgrades will not be
performed).
29. This Limited Warranty is applicable only to the original purchaser and it is non-transferable.
30. This warranty only covers Enviro products that are purchased through an authorized Enviro dealer.
31. If for any reason any section of the Limited Warranty is declared invalid, the balance of the warranty
remains in effect and all other clauses shall remain in effect.
32. The Limited Warranty is the only warranty supplied by Sherwood Industries Ltd., the manufacturer
of the stove. All other warranties, whether express or implied, are hereby expressly disclaimed and
purchaser’s recourse is expressly limited to the Limited Warranty.
33. Sherwood Industries Ltd. and its employees or representatives will not assume any damages, either
directly or indirectly, caused by improper usage, operation, installation, servicing or maintenance of this
stove.
34. Sherwood Industries Ltd. reserves the right to make changes without notice. Please complete and mail
the warranty registration card and have the installer fill in the installation data sheet in the back of the
manual for warranty and future reference.
35. Sherwood Industries Ltd. is responsible for stocking parts for a maximum of seven (7) years after
discontinuing the manufacture or incorporation of the item into its products. An exception to this would
be if an OEM supplier is not able to supply a part.
30
Installation Data Sheet
The following information must be recorded by the installer for warranty purposes and future reference.
NAME OF OWNER:
NAME OF DEALER:
_________________________________________
_________________________________________
ADDRESS:
ADDRESS:
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
_________________________________________
PHONE:___________________________________
PHONE:___________________________________
MODEL:___________________________________
NAME OF INSTALLER:
SERIAL NUMBER:___________________________
DATE OF PURCHASE: _____________
_________________________________________
(dd/mm/yyyy)
DATE OF INSTALLATION:___________(dd/mm/yyyy)
ADDRESS:
MAGNEHELIC AT INSTALL:___________________
_________________________________________
INSTALLER’S SIGNATURE:
_________________________________________
_________________________________________
_________________________________________
PHONE:___________________________________
MANUFACTURED BY:
SHERWOOD INDUSTRIES LTD.
6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3
www.enviro.com
June 17, 2010
C-12146
31