Black & Decker GTC610P Instruction manual

GTC610
1
Copyright Black & Decker
2
3
2
1
6
4
5
10
9
8
7
7
A
3
1
3
2
11
6
B
C
12
D1
4
D2
D3
D4
5
ENGLISH
CORDLESS HEDGETRIMMER
GTC610
CONGRATULATIONS!
You have chosen a Black & Decker tool. Our aim is
to provide quality tools at an affordable price.
We hope that you will enjoy using this tool for
many years.
EC DECLARATION OF CONFORMITY
GTC610
Black & Decker declares that these tools
conform to: 98/37/EC, 89/336/EEC,
73/23/EEC, EN 50260, EN 55014,
EN 61000, EN 60335
2000/14/EC, hedge trimmer, 1300 min-1,
Annex V
Level of sound pressure, measured according to
2000/14/EC:
INTENDED USE
Your Black & Decker hedgetrimmer GTC610 has
been designed for trimming hedges, shrubs and
brambles. This tool is intended for consumer use
only.
Your Black & Decker charger has been designed
for charging Black & Decker batteries of the type
supplied with this tool.
SAFETY INSTRUCTIONS
Warning symbols
The following symbols are used in this manual:
Denotes risk of personal injury, loss of life
or damage to the tool in case of nonobservance of the instructions in this
manual.
GTC610
LpA (sound pressure)
dB(A)
72
LWA (acoustic power)
dB(A)
86
LWA (guaranteed)
dB(A)
90
Denotes risk of electric shock.
Read the manual prior to operation.
Hand/arm weighted vibration value according to
EN 50260:
Fire hazard.
< 2.5 m/s2
Know your tool
◆
◆
Colin Wills
Director of Engineering
BDCI, 4/F, 2 Dai Wang Street
Tai Po Industrial Estate
Tai Po NT, Hong Kong
1-7-2003
6
◆
◆
Warning! Carefully observe the
instructions in this manual to reduce the
risk of personal injury or material damage.
Read all of this manual carefully before
operating the tool.
Before operating the tool, make sure
that you know how to switch the tool off
in an emergency.
Retain this manual for future reference.
ENGLISH
General
1. Consider work area environment
Do not expose the tool to rain. Do not use the
tool in damp or wet conditions. Keep the work
area well lit. Do not use the tool where there is
a risk of causing fire or explosion, i.e. in the
presence of flammable liquids and gases. Keep
the work area free from debris and obstacles.
2. Keep children away
Do not allow children, visitors or animals to
come near the work area or to touch the tool.
3. Store idle tools
When not in use, tools and batteries should be
stored in a dry place, out of reach of children.
4. Dress properly
Do not wear loose clothing or jewellery, as
these can be caught in moving parts. Preferably
wear working gloves and non-slip footwear
when working outdoors. Wear protective hair
covering to keep long hair out of the way.
5. Personal protection
Wear safety goggles and a face or dust mask
whenever the operations may produce dust or
flying particles. Wear ear protection whenever
the sound level seems uncomfortable.
6. Do not overreach
Keep proper footing and balance at all times.
7. Stay alert
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
8. Use appropriate tool
The intended use is described in this
instruction manual. Do not force small tools or
attachments to do the job of a heavy-duty tool.
The tool will do the job better and safer at the
rate for which it was intended. The use of any
accessory or attachment or performance of any
operation with this tool other than those
recommended in this instruction manual may
present a risk of personal injury. Do not force
the tool.
9. Maintain tools with care
Keep cutting tools sharp and clean for better
and safer performance. Follow the instructions
for maintenance and changing accessories.
Keep handles and switches dry, clean and free
from oil and grease.
10. Check for damaged parts
Before using the tool, carefully check it for
damage to ensure that it will operate properly
and perform its intended function. Check for
misalignment and seizure of moving parts,
breakage of parts and any other conditions
that may affect its operation. Have any
defective parts repaired or replaced by an
authorised repair agent. Do not use the tool if
any part is defective. Never attempt any
repairs yourself.
11. Remove the battery
Remove the battery when the tool is not in
use, before changing any parts of the tool,
accessories or attachments and before
servicing.
12. Avoid unintentional starting
Do not carry the tool with a finger on the
on/off switch.
13. Do not abuse cord
Never carry the charger by its cord or pull it to
disconnect from the socket. Keep the cord
away from heat, oil and sharp edges.
Additional safety instructions for batteries and
chargers
Batteries
◆ Never attempt to open for any reason.
◆ Do not expose to water.
◆ Do not store in locations where the
temperature may exceed 40 °C.
◆ Charge only at ambient temperatures between
4 °C and 40 °C.
◆ Charge only using the charger provided with
the tool (see technical data).
◆ Before charging, make sure that the battery is
dry and clean.
◆ Use only the correct type of battery for the tool
(see technical data).
◆ When disposing of batteries, follow the
instructions given in the section “Protecting
the environment”.
◆ Under extreme conditions, battery leakage
may occur. When you notice liquid on the
battery, proceed as follows:
7
ENGLISH
◆
◆
Carefully wipe the liquid off using a
cloth. Avoid skin contact.
In case of skin or eye contact, follow the
instructions below.
The battery fluid, a 25-30% solution of
potassium hydroxide, can be harmful. In
case of skin contact, immediately rinse
with water. Neutralise with a mild acid
such as lemon juice or vinegar. In case of
eye contact, rinse abundantly with clean
water for at least 10 minutes.
Consult a physician.
Wear gloves when operating this tool.
Do not expose the tool to rain or high
humidity.
◆
◆
◆
Fire hazard! Avoid short-circuiting the
contacts of a detached battery (e.g. when
storing the battery in a toolbox).
◆
◆
◆
Do not incinerate the battery.
◆
Do not attempt to charge damaged
batteries.
◆
Chargers
◆ Use your Black & Decker charger only to
charge batteries of the type supplied with your
tool. Other batteries could burst, causing
personal injury and damage.
◆ Never attempt to charge non-rechargeable
batteries.
◆ Have defective cords replaced immediately.
◆ Do not expose to water.
◆ Do not open the charger.
◆ Do not probe the charger.
◆
◆
◆
◆
Intended for indoor use only.
Additional safety instructions for hedgetrimmers
Wear safety goggles when operating this
tool.
8
◆
Do not carry the tool with your hands on the
front handle switch or the trigger switch unless
the battery has been removed.
If you have not used a hedgetrimmer before,
preferably seek practical instruction by an
experienced user in addition to studying this
manual.
Never touch the blades while the tool is running.
Never attempt to force the blades to come to
a standstill.
Do not put the tool down until the blades have
come to a complete standstill.
Regularly check the blades for damage and
wear. Do not use the tool when the blades are
damaged.
Take care to avoid hard objects (e.g. metal
wire, railings) when trimming. Should you
accidentally hit any such object, immediately
switch the tool off and check for any damage.
Should the tool start to vibrate abnormally,
immediately switch it off and check for any
damage.
If the tool stalls, immediately switch it off.
Remove the battery before attempting to
remove any obstructions.
After use, place the blade sheath supplied
over the blades. Store the tool, making sure
that the blade is not exposed.
Always ensure that all guards are fitted when
using the tool. Never attempt to use an
incomplete tool or a tool with unauthorised
modifications.
Never allow children to use the tool.
Be aware of falling debris when cutting the
higher sides of a hedge.
Additional safety instructions for Australia and
New Zealand
◆ This appliance is not intended for use by
young or infirm persons without supervision.
Children must be supervised to ensure they do
not play with the appliance.
ENGLISH
◆
If the supply cord is damaged, it must be
replaced by the manufacturer or an authorised
Black & Decker Service Centre in order to
avoid a hazard.
ELECTRICAL SAFETY
Your charger has been designed for a specific
mains voltage. Always check that the mains voltage
corresponds to the voltage on the rating plate.
Your charger is double insulated in
accordance with EN 60335; therefore no
earth wire is required.
Mains plug replacement (U.K. & Ireland only)
◆
◆
◆
◆
◆
◆
◆
Should your mains plug need replacing and you
are competent to do this, proceed as instructed
below. If you are in doubt, contact an authorised
repair agent or a qualified electrician.
Disconnect the plug from the supply.
Cut off the plug and dispose of it safely; a plug
with bared copper conductors is dangerous if
engaged in a live socket outlet.
Only fit 13 Amperes BS1363A approved plugs
fitted with a 3 A fuse (1).
The cable wire colours, or a letter, will be marked
at the connection points of most good quality
plugs. Attach the wires to their respective points
in the plug (see above). Brown is for Live (L) (2),
blue is for Neutral (N) (4).
Before replacing the top cover of the mains
plug ensure that the cable restraint (3) is
holding the outer sheath of the cable firmly
and that the leads are correctly fixed at the
terminal screws.
After replacing the fuse in the moulded plug,
make sure that the fuse cover is refitted.
Do not use the plug if the fuse cover is missing
or damaged.
Never use a light socket.
CARTON CONTENTS
The carton contains:
1 Cordless hedgetrimmer
1 Battery
1 Charger
1 Blade sheath
1 Instruction manual
◆
Carefully unpack all parts.
OVERVIEW (fig. A)
1. Front handle switch
2. Trigger switch
3. Lock-off button
4. Ventilation slots
5. Guard
6. Battery
7. Charger
8. Charging indicator
9. End of charge indicator
10. Blade sheath
ASSEMBLY
Before assembly, remove the battery from
the tool.
Fitting and removing the battery (fig. B)
◆ To fit the battery (6), line it up with the
receptacle on the tool. Slide the battery into
the receptacle and push until the battery snaps
into place.
◆ To remove the battery, push the release
button (11) while at the same time pulling the
battery out of the receptacle.
USE
Let the tool work at its own pace.
Do not overload.
Charging the battery (fig. A)
The battery needs to be charged before first use
and whenever it fails to produce sufficient power on
jobs that were easily done before.
9
ENGLISH
When charging the battery for the first time, or after
prolonged storage, it will only accept an 80% charge.
After several charge and discharge cycles, the
battery will attain full capacity. The battery may
become warm while charging; this is normal and
does not indicate a problem.
Do not charge the battery at ambient
temperatures below 4 °C or above 40 °C.
Recommended charging temperature:
approx. 24 °C.
◆
◆
To charge the battery (6), remove it from the
tool and insert it into the charger (7).
The battery will only fit into the charger in one
way. Do not force. Be sure that the battery is
fully seated in the charger.
Plug in the charger.
3 hour charger
The battery will be fully charged in approx. 3 hours.
It can be removed at any time or left in the
connected charger indefinitely.
1 hour charger
◆ Check if the red charging indicator (8) lights up.
If the green end of charge indicator (9) lights
up now instead, the battery is too hot and
cannot be charged. If this happens, remove
the battery from the charger, let the battery
cool down for approx. 1 hour and re-insert it.
After approx. 1 hour of charging, the red charging
indicator (8) will stop lighting and the green end of
charge indicator (9) will light up. The battery is
now fully charged.
◆ Remove the battery from the charger.
Switching on and off (fig. C)
For your safety, this tool is equipped with a
double switching system. This system prevents
starting the tool inadvertently and will only allow
operation while holding the tool with both hands.
Switching on
◆ Squeeze the front handle switch (1).
◆ Push the lock-off button (3) forward using your
thumb and at the same time squeeze the
trigger switch (2).
10
◆
Release the lock-off button.
Switching off
◆ Release the front handle switch (1) or the
trigger switch (2).
Never attempt to lock a switch in the on
position.
Hints for optimum use
◆ Slightly tilt the tool (up to 15° relative to the
line of cut) so that the blade tips point slightly
towards the hedge (fig. D1). This will cause the
blades to cut more effectively.
◆ Start by trimming the top of the hedge. Hold the
tool at the desired angle and move it steadily
along the line of cut (fig. D2). The double-sided
blade allows you to cut in either direction.
◆ In order to obtain a very straight cut, stretch a
piece of string along the length of the hedge
at the desired height. Use the string (12) as a
guideline, cutting just above it (fig. D2).
◆ In order to obtain flat sides, cut upwards with
the growth (fig. D3). Younger stems move
outwards when the blade cuts downwards,
causing shallow patches in the hedge.
◆ Take care to avoid any foreign objects. Especially
avoid hard objects such as metal wire and railings,
as these could damage the blades (fig. D4).
◆ Regularly oil the blades.
◆ Consider purchasing a spare battery to extend
the running time of this tool. The catalogue
number of the battery is found in the technical
data chart below.
MAINTENANCE
Your Black & Decker tool has been designed to
operate over a long period of time with a minimum
of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Your charger does not require any maintenance
apart from regular cleaning.
◆
◆
Before performing any maintenance on
the tool, remove the battery from
the tool.
Unplug the charger before cleaning it.
ENGLISH
◆
◆
◆
After use, carefully clean the blades.
After cleaning, apply a film of light machine oil
to prevent the blades from rusting.
Regularly clean the ventilation slots in your tool
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a
damp cloth. Do not use any abrasive or
solvent-based cleaner.
PROTECTING THE ENVIRONMENT
Black & Decker provides a facility for
recycling Black & Decker products once
they have reached the end of their
working life. This service is provided free
of charge. To take advantage of this
service please return your product to any
authorised repair agent who will collect
them on our behalf.
You can check the location of your nearest
authorised repair agent by contacting your local
Black & Decker office at the address indicated in
this manual. Alternatively, a list of authorised
Black & Decker repair agents and full details of our
after-sales service and contacts are available on
the Internet at: www.2helpU.com.
Technical data
Voltage
Blade strokes (no load)
Blade length
Blade gap
Blade brake time
Weight (without battery)
VDC
min-1
cm
mm
s
kg
Battery
Voltage
Capacity
Weight
Charger
Input voltage
(Australia & New Zealand)
Approx. charging time
Weight
GTC610
18
1,300
51
12
< 0.5
2.2
VDC 18
Ah 1.5
kg 0.8
VAC
VAC
h
kg
230
240
3
0.4
230
240
1
1.2
GUARANTEE
Black & Decker is confident of the quality of its
products and offers an outstanding guarantee.
This guarantee statement is in addition to and in
no way prejudices your statutory rights.
The guarantee is valid within the territories of the
Member States of the European Union and the
European Free Trade Area.
If a Black & Decker product becomes defective
due to faulty materials, workmanship or lack of
conformity, within 24 months from the date of
purchase, Black & Decker guarantees to replace
defective parts, repair products subjected to fair
wear and tear or replace such products to ensure
minimum inconvenience to the customer unless:
◆ The product has been used for trade,
professional or hire purposes;
◆ The product has been subjected to misuse or
neglect;
◆ The product has sustained damage through
foreign objects, substances or accidents;
◆ Repairs have been attempted by persons other
than authorised repair agents or Black & Decker
service staff.
To claim on the guarantee, you will need to
submit proof of purchase to the seller or an
authorised repair agent. You can check the
location of your nearest authorised repair agent by
contacting your local Black & Decker office at the
address indicated in this manual. Alternatively, a
list of authorised Black & Decker repair agents and
full details of our after-sales service and contacts
are available on the Internet at: www.2helpU.com.
OTHER OUTDOOR TOOLS
Black & Decker has a full range of outdoor power
tools that make life in the garden easy. If you
would like further information on the following
products, please contact our Service and Information
Centre (see the address page towards the end of
this manual) or your local Black & Decker retailer.
Blade and string trimmers
Chainsaws
Cordless shears
Cordless trimsaws
Hedgetrimmers
Lawnmowers
Lawnrakers
Leafbusters
Shredders
Cordless brooms and shrubbers
Not all products are available in all countries.
11
Australia
DEWALT Industrial Power Tool Company
7 Clarice Road
Box Hill, Victoria 3128
Tel. 03 9895 9200
Fax 03 9899 7465
New Zealand
Black & Decker
81 Hugo Johnston Drive
Penrose, Auckland, New Zealand
Tel. 09 579 7600
Fax 09 579 8200
United Kingdom
Black & Decker
210 Bath Road
Slough, Berkshire SL1 3YD
Tel. 01753 511234
Fax 01753 551155
Helpline 01753 574277
585299-00
12
08/03