Micro-Tech 2400 Amplifier Service Manual
POWER AMPLIFIER
SERVICE MANUAL
MICRO-TECH -2400
®
©1995 by CROWN INTERNATIONAL, INC.
Mailing Address:
P.O. Box 1000
Elkhart, IN U.S.A. 46515-1000
Shipping Address:
57620 C.R. 105
Elkhart, IN U.S.A. 46517
Micro-Tech®, ODEP® and Crown® are registered trademarks of Crown International, Inc.
K-SVCMT24
7-95
1
Micro-Tech 2400 Amplifier Service Manual
The information furnished in this manual does not include all of the details of design, production, or variations
of the equipment. Nor does it cover every possible situation which may arise during installation, operation or
maintenance. If you need special assistance beyond the scope of this manual, please contact the Crown
Technical Support Group.
Mail: P.O. Box 1000 Elkhart IN 46515-1000
Shipping: 57620 C.R. 105 Elkhart IN 46517
Phone: (800) 342-6939/(219) 294-8200
FAX: (219) 294-8301
CAUTION
AVIS
TO PREVENT ELECTRIC SHOCK DO
NOT REMOVE TOP OR BOTTOM
COVERS. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL. DISCONNECT
POWER CORD BEFORE REMOVING
REAR INPUT MODULE TO ACCESS
GAIN SWITCH.
À PRÉVENIR LE CHOC
ÉLECTRIQUE N’ENLEVEZ
PAS LES COUVERTURES.
RIEN DES PARTIES
UTILES À L’INTÉRIEUR.
DÉBRANCHER LA BORNE
AVANT D’OUVRIR LA
MODULE EN ARRIÈRE.
WARNING
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE!
2
Micro-Tech 2400 Amplifier Service Manual
Table of Contents
Introduction ............................................................. 4
Scope ...................................................................... 4
Warranty .................................................................. 4
Parts Information ..................................................... 5
Specifications .......................................................... 6
Voltage Conversion ................................................. 7
Circuit Theory .......................................................... 8
Electrical Checkout Procedures ............................ 13
Parts List (Non-Module) ........................................ 16
Module Information ............................................... 19
M46330-3 Fuse Module ........................................ 20
Q43327-8 Display Module .................................... 20
Q43354-2 Output Module ..................................... 21
Q43328-6 Main Module ......................................... 22
Q43399-7 Main Module ......................................... 26
3
Micro-Tech 2400 Amplifier Service Manual
Introduction
This manual contains service information on Crown
power amplifiers. It is designed to be used in conjunction with the applicable Owner's Manual. However,
some important information is duplicated in this Service Manual in case the Owner's Manual is not readily
available.
Each of the compact audio power amplifiers are
designed for professional or commercial use. Providing high power amplification from 20Hz to 20KHz with
minimum distortion, they feature balanced inputs with
bridged and parallel monophonic capability. Specific
features vary depending on model family.
NOTE: THE INFORMATION IN THIS MANUAL IS INTENDED
FOR USE BY AN EXPERIENCED TECHNICIAN ONLY!
WARRANTY
SCOPE
This Service Manual includes several sections. These
sections include Parts Information, Specifications,
Voltage Conversion, Circuit Theory, Electrical Test
Procedures, Non-Module Parts Lists, and Module
Parts Lists. Schematics are attached. Note that component parts with circuit board comprise a complete
module. Module part numbers are always associated
with a specific circuit board, although an unpopulated
circuit board may be built up with different parts to
create different modules. Note that Crown does not
sell blank (unpopulated) circuit boards.
Each Owner's Manual contains basic policies as related to the customer. In addition it should be stated
that this service documentation is meant to be used
only by properly trained service personnel. Because
most Crown products carry a 3 Year Full Warranty
(including round trip shipping within the United States),
all warranty service should be referred to the Crown
Factory or Authorized Warranty Service Center. See
the applicable Owner’s Manual for warranty details. To
find the location of the nearest Authorized Service
Center or obtain instructions for receiving Crown Factory Service please contact the Crown Technical Support Group (within North America) or your Crown/
Amcron Importer (outside North America).
Crown
Technical Support Group
Factory Service
Parts Department
Mailing Address:
PO Box 1000
Elkhart, IN USA 46515-1000
Shipping Address:
57620 C.R. 105
Elkhart, IN USA 46517
Phone: (219) 294-8200
Toll Free: (800) 342-6939
FAX: (219) 294-8301
4
Micro-Tech 2400 Amplifier Service Manual
Parts Information
GENERAL INFORMATION
Later sections include both mechanical and electrical
parts lists for this product. The parts listed are current
as of the date printed. Crown reserves the right to
modify and improve its products for the benefit of its
customers.
PART NUMBERING SYSTEMS
As of the printing of this manual, Crown is using two
numbering systems. The elder system always uses
eight characters. The first character is a letter. Common letters used are C, D, H, M, P, and Q. The second
through sixth characters are numbers. The numbers
build sequentially (for each prefix letter) as new parts
are added to our parts inventory system. (In some
cases there will be a space then a four character
number after the prefix letter; the space is considered
a character.) The seventh character is usually a hyphen, though it may be a letter to indicate a revision or
special note. The last character is called a check-digit,
and is useful to Crown for internal tracking.
Crown is in the process of converting to a new part
number system. Length may vary from eight to twelve
characters. There is still a letter prefix, then five
numbers. These five numbers identify a type of part.
The seventh character is a hyphen. Remaining characters identify the details of the type of part identified
by the first part of the number.
STANDARD AND SPECIAL PARTS
Many smaller electrical and electronic parts used by
Crown are stocked by and available from electronic
supply houses. However, some electronic parts that
appear to be standard are actually special. A part
ordered from Crown will assure an acceptable replacement. Structural items such as modules and
panels are available from Crown only.
ORDERING PARTS
When ordering parts, be sure to give the product
model, and include a description and part number
(CPN/DPN) from the parts listing. Price quotes are
available on request.
shipment on a C.O.D. or pre-payment (check or credit
card) basis.
TERMS
Normal terms are pre-paid. Net-30 Days applies to
only those firms having pre-established accounts with
Crown. If pre-paying, the order must be packed and
weighed before a total bill can be established, after
which an amount due will be issued and shipment
made upon receipt of pre-payment. New parts returned for credit are subject to a 10% re-stocking fee,
and authorization from the Crown Parts Department
must be obtained before returning parts for credit.
Crown is not a general parts warehouse. Parts sold by
the Crown Parts Department are solely for servicing
Crown/Amcron products. Part prices and availability are subject to change without notice.
Crown
Parts Department
Mailing Address:
PO Box 1000
Elkhart, IN USA 46515-1000
Shipping Address:
57620 C.R. 105
Elkhart, IN USA 46517
Phone: (219) 294-8210
or: (219) 294-8211
Toll Free: (800) 342-6939
FAX: (219) 294-8301
SHIPMENT
Shipment will be normally made by UPS or best other
method unless you specify otherwise. Shipments are
made to and from Elkhart, Indiana USA, only. Established accounts with Crown will receive shipment
freight prepaid and will be billed. All others will receive
5
Micro-Tech 2400 Amplifier Service Manual
Specifications
Unless noted otherwise, all specifications are based
on driving an 8 ohm load per channel, both channels
driven, the sensitivity switch in the 26dB position, the
AC supply is 120VAC at 60Hz. Crown specifications
are guaranteed through the warranty period (normally
3 years). Because our testing methods are more stringent than our published specifications, every Crown
amplifier will exceed its published specifications.
POWER
Power
8 Ohm Stereo—520W/Ch
4 Ohm Stereo—800W/Ch
2 Ohm Stereo—1050W/Ch
8 Ohm Bridge Mono—1585W
4 Ohm Bridge Mono—2070W
2 Ohm Parallel Mono—1530W
1 Ohm Parallel Mono—2080W
Load Impedances: Rated for 16, 8, 4, 2, and 1 (parallel
mono only) Ohm operation; safe with all types of loads,
even totally reactive loads.
AC Mains: 120VAC at 60 Hz with standard three-wire
grounded connector for North American units; 100VAC,
120VAC, 220VAC, and 240VAC at 50 or 60 Hz when
equipped with universal transformers, applicable fan
assembly, and other applicable hardware with country specific power cord.
PERFORMANCE
Frequency Response: ±0.1dB from 20 Hz to 20 kHz at 1
Watt.
Phase Response: ±10° from 10 Hz to 20 kHz at 1 Watt.
Signal to Noise Ratio: A-weighted, better than 105 dB
below full rated output. Better than 100 dB below full
rated output from 20 Hz to 20 kHz.
Total Harmonic Distortion (THD): <0.05% from 20 Hz to
1 kHz, increasing linearly to 0.1% at 20 kHz at 500W.
I.M. Distortion: <0.05% from less than 164 milliwatts to
520 W at 26 dB gain.
Slew Rate: >13V per microsecond. (Slew rates are
limited to useful levels for ultrasonic/RF protection.)
Damping Factor: >1000 from 10 Hz to 400 Hz.
DC Offset: <10 millivolts.
6
Input Impedance: Nominally 20K ohms balanced; 10K
ohms unbalanced.
Output Impedance: <10 milliohms in series with <2
microhenries.
Protection Systems: Output Device Emulation Protection (ODEP) limits drive in the event of dangerous
dynamic thermal conditions without interrupting power.
Current limiting for shorted load protection. DC/LF and
common mode output current Fault circuitry to mute
audio. Delay of 4 seconds from turn on mutes amplifier
to prevent dangerous turn-on transients. A high voltage circuit breaker in each main transformer primary
and a low voltage power supply fuse in fan primary.
Slew rate limiting to prevent RF burn out.
MECHANICAL
Input Connectors: Balanced 1/4 inch phone jacks. Optional XLR inputs with MT-XLR accessory.
Output Connectors: Color-coded 5-way binding posts
on 3/4 inch centers; spaced 3/4 inch apart.
Front Panel Controls: A front panel rocker switch used
to power the amplifier on and off.
Back Panel Controls: A three-position switch which
selects Stereo, Bridge-Mono, or Parallel-Mono mode.
A rotary potentiometer for each channel used to
control output level. A ground lift switch used to isolate
the phone jack input grounds from the chassis (AC)
ground. And a push button circuit breaker for each
channel used to protect the power supplies.
Internal Controls: A three-position switch selects 0.775V,
1.4V, or 26 dB voltage gain input sensitivity.
Indicators: Amber Enable indicator shows on/off status
of low-voltage power supply. An Amber ODEP indicator for each channel shows the reserve energy status.
If no reserve energy is available the indicator will dim
in proportion to ODEP limiting.
Construction: Black splatter-coat steel chassis with
specially designed flow-through ventilation system.
Mounting: Standard EIA 310 front-panel rack mount
with supports for supplemental rear corner mounting.
Dimensions: 19 inches wide, 3.5 inches high, 16 inches
deep behind front mounting surface.
Weight: 46 lbs, 14 oz. Shipping; 55 lbs, 12 oz.
Micro-Tech 2400 Amplifier Service Manual
Voltage Conversion
The 120 Volt 60 Hz version, sold in the United States,
is not voltage selectable. It does not have a voltage
selection board. This version is to be used only with
120 Volts and only with 60Hz.
All other versions of the Micro Tech 2400 use a voltage selection board. The following chart indicates
different configurations of jumpers for different voltages. Note that the circuit breakers, fuse and
transmotor may need to be changed to accommodate different voltages. Versions with the voltage selection board may be used at 50 or 60 Hz.
VOLTAGE SELECTION BOARD
Jumpers
100V
120V
200V
220V/230V
240V
P8—B
B—E
P9—F
C—F
P8—A
A—D
P9—F
C—F
P8—B
C—E
P9—F
P8—B
C—D
P9—F
P8—A
C—D
P9—F
Circuit Breakers
CB100/CB200
C 9508-0
15 Amp
C 8041-3
7.5 Amp
Fuse
F1
A10285-10
1 Amp
A10285-7
.5 Amp
Transmotor
TF1
H43068-8
H43407-8
H43408-6
Note: "P" locations are on the Fuse Board
7
Micro-Tech 2400 Amplifier Service Manual
Theory
OVERVIEW
It should be noted that over time Crown makes improvements and changes to their products for various
reasons. This manual is up to date as of the time of
writing. For additional information regarding these
amplifiers, refer to the applicable Technical Notes
provided by Crown for this product.
This section of the manual explains the general operation of a typical Crown power amplifier. Topics covered include Front End, Grounded Bridge, and ODEP.
Due to variations in design from vintage to vintage
(and similarities with other Crown products) the theory
of operation remains simplified.
FEATURES
Micro Tech amplifiers utilize numerous Crown innovations including grounded bridge and ODEP technologies. Cooling techniques make use of the what is
essentially air conditioner technology. Air flows bottom to top, and front to side. Air flows a short distance
across a wide heatsink. This type of air flow provides
significantly better cooling than the “wind tunnel”
technology used by many other manufacturers. Output transistors are of the metal can type rather than
plastic case. This allows for a significantly higher
thermal margin for the given voltage and current
ratings. All devices used are tested and graded to
ensure maximum reliability. Another electronic technique used is negative feedback. Almost all power
amplifiers utilize negative feedback to control gain
and provide stability, but Crown uses multiple nested
feedback loops for maximum stability and greatly
improved damping. Most Crown amplifiers have damping in excess of 1000 in the bass frequency range. This
feedback, along with our compensation and ultra-low
distortion output topology, make Crown amplifiers
superior.
Features specific to the Micro Tech Series’ include two
seperate power transformers (one for each channel),
a full time full speed fan which also serves as the low
voltage transformer, slew rate limiting, and audio
muting for delay or protective action. This amplifier
can operate in either a Bridged or Parallel Mono mode
as well as dual (stereo). A sensitivity switch allows
selection of input voltage required for rated output.
Level controls are mounted on the rear panel and are
of the rotary type. Front panel indicators let the user
know the status of the low voltage power supply
(enable), and an ODEP indicator for each channel
which shows the reserve energy status. In general, the
8
packaging of this model is designed for maximum
watt/price/weight/size value with user friendly features.
For additional details refer to the specification section,
or to the applicable Owner’s Manual.
FRONT END OPERATION
The front end is comprised of three stages: Balanced
Gain Stage (BGS), Variable Gain Stage (VGS), and
the Error Amp. Figure 1 shows a simplified diagram of
a typical front end with voltage amplification stages.
Balanced Gain Stage (BGS)
Input to the amplifier is balanced. The shield may be
isolated from chassis ground by an RC network to
interrupt ground loops via the Ground Lift Switch. The
non-inverting (hot) side of the balanced input is fed to
the non-inverting input of the first op-amp stage. The
inverting (negative) side of the balanced input is fed
to the inverting input of the first op-amp stage. A
potentiometer is provided for common mode rejection
adjustment. Electrically, the BGS is at unity gain.
(From an audio perspective, however, this stage
actually provides +6dB gain if a fully balanced signal
is placed on its input.) The BGS is a non-inverting
stage. It’s output is delivered to the Variable Gain
Stage.
Variable Gain Stage (VGS)
From the output of the BGS, the signal goes to the VGS
where gain is determined by the position of the Sensitivity Switch, and level is determined by the level
control. VGS is an inverting stage with the input being
fed to its op-amp stage. Because gain after this stage
is fixed at 26dB (factor of 20), greater amplifier sensitivity is achieved by controlling the ratio of feedback to
input resistance. The Sensitivity Switch sets the input
impedance to this stage and varies the gain such that
the overall amplifier gain is 26 dB, or is adjusted
appropriately for 0.775V or 1.4V input to attain rated
output.
Error Amp
The inverted output from the VGS is fed to the noninverting input of the Error Amp op-amp stage through
an AC coupling capacitor and input resistor. Amplifier
output is fed back via the negative feedback (NFb)
loop resistor. The ratio of feedback resistor to input
resistor fixes gain from the Error Amp input to the
output of the amplifier at 26 dB. Diodes prevent
overdriving the Error Amp. Because the Error Amp
Micro-Tech 2400 Amplifier Service Manual
Theory
The ODEP transistors steal drive as dictated by the
ODEP circuitry (discussed later). The control/protection transistors act as switches to totally shunt audio to
ground during the turn-on delay, or during a DC/LF or
Fault protective action.
amplifies the difference between input and output
signals, any difference in the two waveforms will
produce a near open loop gain condition which in turn
results in high peak output voltage. The output of the
Error Amp, called the Error Signal (ES) drives the
Voltage Translators.
Last Voltage Amplifiers (LVAs)
The Voltage Translator stage channels the signal to
the Last Voltage Amplifiers (LVA's) in a balanced
configuration. The +LVA and -LVA, with their push-pull
effect through the Bias Servo, drive the fully complementary output stage. The LVAs are configured as
common emitter amplifiers. This configuration provides sufficient voltage gain and inverts the audio. The
polarity inversion is necessary to avoid an overall
polarity inversion from input jack to output jack, and it
allows the NFb loop to control Error Amp gain by
feeding back to its non-inverting input (with its polarity
opposite to the output of the VGS). With the added
voltage swing provided by the LVAs, the signal then
gains current amplification through the Darlington
emitter-follower output stage.
VOLTAGE AMPLIFICATION
The Voltage Translator stage separates the output of
the Error Amp into balanced positive and negative
drive voltages for the Last Voltage Amplifiers (LVAs),
translating the signal from ground referenced ±15V to
±Vcc reference. LVAs provide the main voltage amplification and drive the High Side output stages. Gain
from Voltage Translator input to amplifier output is a
factor of 25.2.
Voltage Translators
A voltage divider network splits the Error Signal (ES)
into positive and negative drive signals for the balanced voltage translator stage. These offset reference
voltages drive the input to the Voltage Translator
transistors. A nested NFb loop from the output of the
amplifier mixes with the inverted signal riding on the
offset references. This negative feedback fixes gain at
the offset reference points (and the output of the Error
Amp) at a factor of -25.2 with respect to the amplifier
output. The Voltage Translators are arranged in a
common base configuration for non-inverting voltage
gain with equal gain. They shift the audio from the
±15V reference to VCC reference. Their outputs drive
their respective LVA.
GROUNDED BRIDGE TOPOLOGY
Figure 2 is a simplified example of the grounded
bridge output topology. It consists of four quadrants
of three deep Darlington (composite) emitter-follower
stages per channel: one NPN and one PNP on the
High Side of the bridge (driving the load), and one
NPN and one PNP on the Low Side of the bridge
(controlling the ground reference for the rails). The
output stages are biased to operate class AB+B for
ultra low distortion in the signal zero-crossing region
and high efficiency.
Also tied into the Voltage Translator inputs are ODEP
limiting transistors and control/protection transistors.
Voltage
Translators
Audio
Inputs
+
-
VGS
+
-
Error
Amp
+
-
Voltage Divider
+15V
BGS
Q105
Q100
Q121
Q101
NPN Outputs (+HS)
PNP Outputs (-HS)
Q102
Q103
Q122
-+
-15V
+VCC
ODEP
Mute
NFb Loop
Q110
-VCC
LVA's
Figure 1. Typical Amplifier Front End and Voltage Amplification Stages.
9
Micro-Tech 2400 Amplifier Service Manual
Theory
High Side (HS)
The High Side (HS) of the bridge operates much like
a conventional bipolar push-pull output configuration.
As the input drive voltage becomes more positive, the
HS NPN conducts and delivers positive voltage to the
load. Eventually the NPN devices reach full conduction and +Vcc is across the load. At this time the HS
PNP is biased off. When the drive signal is negative
going, the HS PNP conducts to deliver -Vcc to the load
and the HS NPN stage is off.
The output of the +LVA drives the base of predriver
device. Together, the predriver and driver form the
first two parts of the three-deep Darlington and are
biased class AB. They provide output drive through
the bias resistor, bypassing the output devices, at
levels below about 100mW. An RLC network between
the predriver and driver provide phase shift compensation and limit driver base current to safe levels.
Output devices are biased class B, just below cutoff.
At about 100mW output they switch on to conduct high
current to the load. Together with predriver and driver,
the output device provide an overall class AB+B
output.
The negative half of the HS is almost identical to the
positive half, except that the devices are PNP. One
difference is that the PNP bias resistor is slightly
greater in value so that PNP output devices run closer
to the cutoff level under static (no signal) conditions.
This is because PNP devices require greater drive
current.
HS bias is regulated by Q18, the Bias Servo. Q18 is a
Vbe multiplier which maintains approximately 3.3V
Vce under static conditions. The positive and negative
halves of the HS output are in parallel with this 3.3V.
With a full base-emitter on voltage drop across
predrivers and drivers, the balance of voltage results
in approximately .35V drop across the bias resistors in
the positive half, and about .5V across the bias resistor
in the negative half. Q18 conduction (and thus bias) is
adjustable.
A diode string prevents excessive charge build up
within the high conduction output devices when off.
Flyback diodes shunt back-EMF pulses from reactive
loads to the power supply to protect output devices
from dangerous reverse voltage levels. An output
terminating circuit blocks RF on output lines from
entering the amplifier through its output connectors.
Low Side (LS)
The Low Side (LS) operates quite differently. The
power supply bridge rectifier is not ground referenced, nor is the secondary of the main transformer.
In other words, the high voltage power supply floats
with respect to ground, but ±Vcc remain constant with
+
+Vcc (Positive Rail)
Input
signal
HIGH SIDE
Load
(speaker)
Inverting Op-amp
-Vcc (Negative Rail)
-
Figure 2. Crown Patented Grounded Bridge Topology
10
LOW SIDE
Micro-Tech 2400 Amplifier Service Manual
Theory
respect to each other. This allows the power supply to
deliver +Vcc and -Vcc from the same bridge rectifier
and filter as a total difference in potential, regardless
of their voltages with respect to ground. The LS uses
inverted feedback from the HS output to control the
ground reference for the rails (±Vcc). Both LS quadrants are arranged in a three-deep Darlington and are
biased AB+B in the same manner as the HS.
When the amplifier output swings positive, the audio is
fed to an op-amp stage where it is inverted. This
inverted signal is delivered directly to the bases of the
positive (NPN) and negative (PNP) LS predrivers. The
negative drive forces the LS PNP devices on (NPN
off). As the PNP devices conduct, Vce of the PNP
Darlington drops. With LS device emitters tied to
ground, -Vcc is pulled toward ground reference.
Since the power supply is not ground referenced (and
the total voltage from +Vcc to -Vcc is constant) +Vcc
is forced higher above ground potential. This continues until, at the positive amplifier output peak, -Vcc =
0V and +Vcc equals the total power supply potential
with a positive polarity. If, for example, the power
supply produced a total of 70V from rail to rail (±35VDC
measured from ground with no signal), the amplifier
output would reach a positive peak of +70V.
Conversely, during a negative swing of the HS output
where HS PNP devices conduct, the op-amp would
output a positive voltage forcing LS NPN devices to
conduct. This would result in +Vcc swinging toward
ground potential and -Vcc further from ground potential. At the negative amplifier output peak, +Vcc = 0V
and -Vcc equals the total power supply potential with
a negative polarity. Using the same example as above,
a 70V supply would allow a negative output peak of 70V. In summary, a power supply which produces a
total of 70VDC rail to rail (or ±35VDC statically) is
capable of producing 140V peak-to-peak at the amplifier output when the grounded bridge topology is
used. The voltage used in this example are relatively
close to the voltages of the PB-1/460CSL.
Low side bias is established by a diode string which
also shunts built up charges on the output devices.
Bias is adjustable via potentiometer. Flyback diodes
perform the same function as the HS flybacks. The
output of the LS is tied directly to chassis ground via
ground strap.
OUTPUT DEVICE EMULATION PROTECTION
(ODEP)
To further protect the output stages, a specially developed ODEP circuit is used. It produces a complex
analog output signal. This signal is proportional to the
always changing safe-operating-area margin of the
output transistors. The ODEP signal controls the Voltage Translator stage by removing drive that may
exceed the safe-operating-area of the output stage.
ODEP senses output current by measuring the voltage dropped across LS emitter resistors. LS NPN
current (negative amplifier output) and +Vcc are
sensed, then multiplied to obtain a signal proportional
to output power. Positive and negative ODEP voltages
are adjustable via two potentiometers. Across ±ODEP
are a PTC and a thermal sense (current source). The
PTC is essentially a cutoff switch that causes hard
ODEP limiting if heatsink temperature exceeds a safe
maximum, regardless of signal level. The thermal
sense causes the differential between +ODEP and –
ODEP to decrease as heatsink temperature increases.
An increase in positive output signal output into a load
will result in –ODEP voltage dropping; an increase in
negative output voltage and current will cause +ODEP
voltage to drop. A complex RC network between the
±ODEP circuitry is used to simulate the thermal barriers between the interior of the output device die
(immeasurable by normal means) and the time delay
from heat generation at the die until heat dissipates to
the thermal sensor. The combined effects of thermal
history and instantaneous dynamic power level result
in an accurate simulation of the actual thermal condition of the output transistors.
The total effect is to deliver a peak to peak voltage to
the speaker load which is twice the voltage produced
by the power supply. Benefits include full utilization of
the power supply (it conducts current during both
halves of the output signal; conventional designs
require two power supplies per channel, one positive
and one negative), and never exposing any output
device to more than half of the peak to peak output
voltage (which does occur in conventional designs).
11
Micro-Tech 2400 Amplifier Service Manual
Theory
BGS
BALANCED
INPUTS
VGS
-1
POSITIVE
HIGH SIDE
OUTPUT
NPN STAGE
+LVA
-1
+VOLTAGE
TRANSLATOR
ERROR
AMP
OUTPUT
DEVICE
EMULATION
PROTECTION
HIGH SIDE
BIAS
SERVO
NEGATIVE
HIGH SIDE
OUTPUT
PNP STAGE
-LVA
-1
-VOLTAGE
TRANSLATOR
MAIN NEGATIVE FEEDBACK (NFb) LOOP
POSITIVE
LOW SIDE
OUTPUT
NPN STAGE
-1
INVERTING
BRIDGE
BALANCE
LOW SIDE
BIAS
DIODE
STRING
NEGATIVE
LOW SIDE
OUTPUT
PNP STAGE
Figure 3. Typical Crown Amplifier Basic Block Diagram (One Channel Shown)
12
Micro-Tech 2400 Amplifier Service Manual
Electrical Checkout Procedures
GENERAL INFORMATION
The following test procedures are to be used to verify
operation of this amplifier. DO NOT connect a load or
inject a signal unless directed to do so by the procedure. These tests, though meant for verification and
alignment of the amplifier, may also be very helpful in
troubleshooting. For best results, tests should be
performed in order.
All tests assume that AC power is from a regulated 120
VAC source. Test equipment includes an oscilloscope, a DMM, a signal generator, loads, and I.M.D.
and T.H.D. noise test equipment.
STANDARD INITIAL CONDITIONS
Level controls fully clockwise.
Stereo/Mono switch in Stereo.
Sensitivity switch in 26 dB fixed gain position.
It is assumed, in each step, that conditions of the
amplifier are per these initial conditions unless otherwise specified.
TEST 1: DC OFFSET
Spec: 0 VDC, ±10 mV.
Initial Conditions: Controls per standard, inputs shorted.
Procedure: Measure DC voltage at the output connectors (rear panel). There is no adjustment for output
offset. If spec is not met, there is an electrical malfunction. Slightly out of spec measurement is usually due
to U104/U204 out of tolorance.
TEST 2: OUTPUT BIAS ADJUSTMENT
Spec: 300 to 320 mVDC.
Initial Conditions: Controls per standard, heatsink temperature less than 40°C.
Procedure: Measure DC voltages on the output module
across R02, adjust R26 if necessary. Measure DC
voltages on the output module across R21, adjust R23
if necessary. Repeat for second channel.
TEST 3: ODEP VOLTAGE ADJUSTMENT
Spec: Bias Per Chart, ±0.1V DC.
Initial Conditions: Controls per standard, heatsink at
room temperature 20 to 30°C (68 to 86°F). Note: This
adjustment should normally be performed within 2
minutes of turn on from ambient (cold) conditions. If
possible measure heatsink temperature, if not measure ambient room temperature. Use this information
when referencing the following chart.
V+ODEP
°F
°C
V–ODEP
66
18.9
–10.31
10.31
68
20.0
–10.26
10.26
70
21.1
–10.20
10.20
72
22.2
–10.14
10.14
74
23.3
–10.09
10.09
76
24.4
–10.03
10.03
77
25.0
–10.00
10.00
78
25.6
–9.97
9.97
80
26.7
–9.91
9.91
82
27.8
–9.86
9.86
84
28.9
–9.80
9.80
86
30.0
–9.74
9.74
88
31.1
–9.69
9.69
90
32.2
–9.63
9.63
92
33.3
–9.57
9.57
94
34.4
–9.51
9.51
–ODEP Procedure: Measure pin 6 of U100 and, if
necessary, adjust R121 to obtain V–ODEP as specified
above. Measure pin 6 of U200 and, if necessary,
adjust R221 to obtain V–ODEP as specified above.
+ODEP Procedure: Measure pin 6 of U103 and, if
necessary, adjust R132 to obtain V+ODEP as specified
above. Measure pin 6 of U203 and, if necessary,
adjust R232 to obtain V+ODEP as specified above.
TEST 4: AC POWER DRAW
Spec: 100 Watts maximum quiescent.
Initial Conditions: Controls per standard.
Procedure: With no input signal and no load, measure
AC line wattage draw. If current draw is excessive,
check for high AC line voltage or high bias voltage.
TEST 5: COMMON MODE REJECTION
Spec at 100 Hz: –70 dB.
Spec at 20 kHz: –50 dB.
Initial Conditions: Controls per standard.
Procedure: No load. Inject a 0 dBu 100 Hz sine wave
into each channel, one channel at a time, with inverting
and non-inverting inputs shorted together. At the
output measure less than –44 dBu. Inject a 0 dBu 20
kHz sine wave into each channel, one channel at a
time, with inverting and non-inverting inputs shorted
together. At the output measure less than –24 dBu.
Adjust R921 or R1021, if necessary, to obtain the
required measurements.
13
Micro-Tech 2400 Amplifier Service Manual
Electrical Checkout Procedures
TEST 6: VOLTAGE GAIN
TEST 10: SLEW RATE & 10 KHZ SQUARE WAVE
Spec 26dB Gain: Gain of 20.0 ±3%.
Spec 0.775V Sensitivity: ±6%.
Spec 1.4V Sensitivity: +12%/–6%.
Initial Conditions: Controls per standard.
Procedure: No load connected. Inject a 0.775 VAC 1
kHz sine wave with the Sensitivity Switch in the 26 dB
position. Measure 15.5 VAC ±0.5 VAC at the amplifier
output. Inject a 0.775 VAC 1 kHz sine wave with the
Sensitivity Switch in the 0.775V position. Measure 64.5
VAC ±3.9 VAC at the amplifier output. Inject a 1.4 VAC
1 kHz sine wave with the Sensitivity Switch in the 1.4V
position. Measure 64.5 VAC +7.7/-3.9 VAC at the
amplifier output. Return the Sensitivity Switch to the 26
dB position.
Spec: 17 - 25 V/µS.
Initial Conditions: Controls per standard.
Procedure: Load each channel to 8 ohms. Inject a 10
kHz square wave to obtain 64 volts peak-to-peak at
each output. Observe the slope of the square wave. It
should typically measure 17 to 25 V/µS. Also, the
square wave must not include overshoot, ringing, or
any type of oscillation.
TEST 7: PHASE RESPONSE
Spec: ±10° from 10 Hz to 20 kHz at 1 Watt.
Initial Conditions: Controls per standard, 8 ohm load on
each channel.
Procedure: Inject a 1 kHz sine wave and adjust for 1
Watt output (2.8 VAC). Check input and output signals
against each other, input and output signals must be
within 10° of each other.
TEST 8: LEVEL CONTROLS
Spec: Level controlled by level controls.
Initial Conditions: Controls per standard.
Procedure: No Load. Inject a 1 kHz sine wave. With
level controls fully clockwise you should see full gain.
As controls are rotated counterclockwise, observe
similar gain reduction in each channel. When complete, return level controls to fully clockwise position.
TEST 9: CURRENT LIMIT
Spec: Current Limit at 38 Amps, ±3 Amps
Initial Conditions: Controls per standard.
Procedure: Load each channel to 1 Ohm. Inject a 1 kHz
differentiated (or 10% duty cycle) square wave. See
figure 4. Increase output level until current limit occurs. Current limit should occur at 38 ±3 Amps (38
Vpk) with output device Vce less than 40 Vpk. Observe clean (no oscillations) current clipping.
Out
In
.047 uF
1K Ohm
Figure 4. Differentiator Circuit
14
TEST 11: CROSSTALK
Spec: -60dB at 20 kHz.
Initial Conditions: Controls per standard. Terminate
input of channel not driven with 600 ohms.
Procedure: 8 ohm load on each channel. Inject a 20 kHz
sine wave into the Channel 1 input and increase output
level to 62 VAC. Measure less than 62 mVAC at the
output of Channel 2. Inject a 20 kHz sine wave into the
Channel 2 input and increase output level to 62 VAC.
Measure less than 62 mVAC at the output of Channel
1.
TEST 12: OUTPUT POWER
Spec at 8 Ohm Stereo: >= 520W at 0.1% THD.
Spec at 4 Ohm Stereo: >= 800W at 0.1% THD.
Spec at 2 Ohm Stereo: >= 934W at 0.1% THD.
International 8 Ohm Stereo: >=515W at 0.1% THD.
International 4 Ohm Stereo: >=745W at 0.1% THD.
International 2 Ohm Stereo: >=925W at 0.1% THD.
Initial Conditions: Controls per standard.
Procedure: Load each channel to 8 ohms. Inject a 1 kHz
sine wave and measure at least 64.5 VAC at the output
of each channel. Load each channel to 4 ohms. Inject
a 1 kHz sine wave and measure at least 56.6 VAC.
Load each channel to 2 ohms. Inject a 1 kHz sine wave
and measure at least 43.2 VAC. All power measurements must be at less than 0.1% THD.
TEST 13: REACTIVE LOADS
Spec: No oscillations. Safe with all types of loads.
Initial Conditions: Controls per standard.
Procedure Capacitive: Load each channel to 8 ohms in
parallel with 2 µF. Inject a 20 kHz sine wave with 55
VAC output for 10 seconds.
Procedure Inductive: Load each channel to 8 ohms in
parallel with 159 µHenries. Inject a 1 kHz sine wave
with 35.8 VAC output for 10 seconds.
Procedure Torture: Load each channel with the primary
(red and black leads) of a DC-300A transformer (D
5781-6). Inject a 15 Hz sine wave at sufficient output
level to cause 3 to 5 flyback pulses, for 10 seconds.
Micro-Tech 2400 Amplifier Service Manual
Electrical Checkout Procedures
Procedure Short: Inject a 60 Hz sine wave at 5 VAC
minimum output. After establishing signal, short the
output for 10 seconds.
TEST 14: ODEP LIMITING
Spec: No oscillation on ODEP Limiting wave form;
either channel controls limiting in Parallel Mono Mode.
Initial Conditions: Controls per standard; rag or other
obstruction blocking fan so that it does not turn.
Procedure: Load the amplifier to 4 ohms on each
channel. Inject a 60 Hz sine wave and adjust for 35
Vrms at the output. After a few minutes observe a wave
form similar to Figure 5. Remove the input signal from
both channels and allow the amplifier to cool for a few
minutes. Switch the amplifier to Parallel Mono and
remove the load from Channel 1. Inject the signal into
Channel 1 and observe that ODEP limiting occurs at
the output of both channels. Remove the load from
Channel 2, and install the load on Channel 1. Again,
observe that both channels limit. Return all amplifier
controls to standard initial conditions. Remove the fan
obstruction.
TEST 16: SIGNAL TO NOISE RATIO
Spec: 100 dB below rated 8 ohm power 20 Hz to 20
kHz. 105 dB A-Weighted.
Initial Conditions: Controls per standard. Short inputs.
Procedure: Load each channel to 8 ohms. Measure
less than 645 µV at the output of each channel (20 Hz20 kHz bandpass filter).
TEST 17: TURN ON TRANSIENTS
Spec: No dangerous transients.
Initial Conditions: Controls per standard.
Procedure: From an off condition, turn on the amplifier
and monitor the output noise at the time of turn on.
Note: Turn on noise may increase significantly if the
amplifier is cycled off and on.
TEST 18: TURN OFF TRANSIENTS
Spec: No dangerous transients.
Initial Conditions: Controls per standard.
Procedure: From an on condition, turn off the amplifier
and monitor the output noise at the time of turn off.
Note: Turn off noise may increase significantly if the
amplifier is cycled off and on.
TEST 19: INTERMODULATION DISTORTION
Spec at 0 dB Output: 0.01%.
Spec at –35 dB Output: 0.05%.
Initial Conditions: Controls per standard.
Procedure: Load each channel to 8 ohms. Inject a
SMPTE standard IM signal (60 Hz and 7 kHz sine
wave mixed at 4:1 ratio). Set the 60 Hz portion of the
sine wave to 51.5 Volt RMS. Set the 7 kHz portion to
25%. With an IM analyzer measure less than 0.01%
IMD. Repeat test at –35 dB (reference 51.5 Volt RMS,
60 Hz portion) and measure less than 0.05% IMD.
TEST 20: CLIPPING
Figure 5. ODEP Limiting Wave Form
TEST 15: LF PROTECTION
Spec: Amplifier mutes for low frequency.
Initial Conditions: Controls per standard.
Procedure: No load. Inject a 0.5 Hz 6 volt peak-to-peak
square wave, or a 2 Hz 6VAC sine wave into each
channel and verify that each channel cycles into mute.
Spec: No protective action during test.
Initial Conditions: Controls per standard.
Procedure: Load each channel to 8 ohms. Inject a 1
kHz sine wave at each input and drive output 6 dB into
clip for 10 seconds. The amplifier should not activate
any protective circuits (ODEP, Fault, or LF Protection).
POST TESTING
After completion of testing, if all tests are satisfactory,
the amplifier controls should be returned to the positions required by customer. If conditions are unknown
or unspecified, factory settings are as follows:
Level Controls: 9 to 11 O’Clock.
Sensitivity Switch: 0.775V U.S., 1.4V International.
Stereo/Mono Switch: Stereo.
Ground Lift: Lift.
Power: Off.
15
Micro-Tech 2400 Amplifier Service Manual
Parts List (Non-Module)
SUPPLIMENTAL ITEMS
CPN
D 4137-2
C 3342-0
A10087-71012
K80603-2
ITEM
Nylon Thumbscrew Washer
Feet, Black Self-Stick
10-32 .75 Machine (Rack Screw)
MT Series Owners Manual
QTY
4
4
4
1
ITEM
Power Cord (US Models)
Power Cord (European plug)
Power Transformer (120V 60 Hz only)
Power Transformer (Universal Volt)
Circuit Breaker, 15A (100V-120V)
Circuit Breaker, 7.5A (200V-240V)
Fuse, 1A 3AG (100V-120V)
Fuse, .5A AGC (200V-240V)
Transmotor (120V 60 Hz Only)
Transmotor (200V-240V Only)
Transmotor (100V Only)
Transmotor (120V 50 Hz)
Fiber Washer, 500ODX195ID (Universal Volt Only)
Fish Paper Insulation (Universal Volt Only)
Universal Volt Wires (Universal Volt Only)
Terminal Jumper Board Ch 2 (Universal Volt Only)
Terminal Jumper Board Ch 1 (Universal Volt Only)
10-32 x 2 PNHD Screw (Mounts Transformers)
#10 Int Tooth Lockwasher
#10 Nylon Shoulder Washer
6-32 x 5/16 undercut Flthd Mscr (XMotor Asm)
Fan Blade, 4.5 Inch CCW
Fan Bracket
6300µF 150V Electrolytic Capacitor
35A 400V Bridge Rectifier
Capacitor Bracket
Shoulder Washer (Cap Asm)
10-32 x .38 Screw (Cap Asm)
1/4" Belleville Spring Washer (Cap Asm)
#10 External Star Lockwasher (Cap Asm)
Blue Wires, Cap Asm
Red Wires, Cap Asm
QTY
1
1
2
2
2
2
1
1
1
1
1
1
2
2
2
1
1
8
8
8
2
1
1
2
2
2
4
4
4
4
2
2
POWER SUPPLY
CPN
D 7975-2
A10793-0503G
D 8633-6
D 8631-0
C 9508-0
C 8041-3
A10285-10
A10285-7
H43409-4
H43408-6
H43068-8
H43407-8
A10101-19
D 8299-6
H43403-7
P10178-5
P10432-6
A10089-11032
A10094-8
A10099-7
C 7062-0
C 9938-9
D 8439-8
D 8639-3
C 8752-5
D 8438-0
D 6764-1
C 9870-4
A10098-5
A10095-4
H43469-8
H43470-6
OUTPUT ASSEMBLY (ONE PER CHANNEL)
CPN
C 8187-4
C 8188-2
C 8573-5
C 8574-3
16
ITEM
NPN Output Device
PNP Output Device
PNP Driver Transistor, TO-3P (2SA1186)
NPN Driver Transistor, TO-3P (2SC2837)
QTY (PER CHANNEL)
6
6
2
2
Micro-Tech 2400 Amplifier Service Manual
Parts List (Non-Module)
OUTPUT ASSEMBLY CONT. (ONE PER CHANNEL)
CPN
D 7665-9
D 7666-7
C 8813-5
B 5842-8
C 5826-0
B 5464-1
D 8774-8
A10315-1
C 9491-9
D 7796-2
D 7797-0
D 8197-2
C 9387-9
F12019-0
M21322J8
ITEM
Clip, TO-3P Mounting
Bracket, TO-3P Heatsink
Q318/Q418 Bias Servo MPSA18/MPS8097
Tubing, #23 TFE Thin Wall Red (For C 8813-5)
S100/S200 Thermal Sense LM334Z
Tubing, #24 Teflon Thin Wall (For C 5826-0)
PTC Thermal Sensor 95DEGC
Screw, 6-32-.56 Hex Washer Head
Screw, 6-32-.312 Taptite Pan Ph
Silpad Insulator (Between Chassis and Heatsinks)
Output Thru-Hole Pad Insulator
Paper Shroud
Rivet, Plastic
Diode Heatsink Slug (Under diodes on Module)
Heatsink, Copper 3/4" with fins
QTY(PER CHANNEL)
2
2
1
Request in Inches
1
Request in Inches
1
12
29
1
1
1
2
1
2
BACK PANEL ASSEMBLY
CPN
M21417J6
M21423J4
F10787J3
C 2823-0
D 7600-6
D 7975-2
A10793-0503G
F11160-3
A10214-7
A10086-70806
A10094-6
A11376-6130J
A11376-6235J
A11394-6160E
A11394-6235E
A11390-6130E
ITEM
Back Panel (US Model)
Back Panel (European Model)
Back Cover Plate
Dual Binding Post Assembly
Ground Strap, Dual Bannana
20A Power Cord (US Models)
European Power Cord
Strain Relief for US Models
Strain Relief, European Model
8-32 X .37 Round Head Machine Screw
#8 Internal Star Lockwasher
13 Inch Black 12 Gauge output wire
23.5 Inch Black 12 Guage output wire
16 Inch Red 12 Guage output wire
23.5 Inch Red 12 Guage output wire
13 Inch Black 22 Guage wire
QTY
1
1
1
2
1
1
1
1
1
2
4
1
1
1
1
1
CHASSIS FRONT ASSEMBLY
CPN
A10090-70806
A10090-70808
A10101-5
A10173-1
D 6944-9
D 8052J8
F12435J7
D 8635-1
ITEM
Screw, 8-32-.375 Mach Ph Oval (Grille)
Screw, 8-32-.5 Mach Ph Oval (End Caps)
Washer, Nylon (Grille)
Clip, Grille Filter
Air Filter
End Cap
Grille
MT-2400 Front Panel Overlay
QTY
3
4
3
3
1
2
1
1
17
Micro-Tech 2400 Amplifier Service Manual
Parts List (Non-Module)
MAIN CHASSIS ASSEMBLY
CPN
D 8501-5
D 8548-6
A10110-70605
M21447J3
ITEM
Cover, Top
Cover, Bottom
Screw, 6-32-.312 Taptite Ph (Covers)
Main Chassis
QTY
1
1
16
1
ITEM
8-32 x .750 Taptite Pnhd Screw
Washer, #6 Black Star
Screw, 8-18-1.375 Pan Ph
Snap Bushing .5
Tension Retainer Board Support
Spacer Nut, 1 inch
Spacer Nut, .75 inch
5.5" Cable Tie
7.5" Cable Tie & Clamp
15" Cable Tie
16.5" 16 Pin Ribbon Cable
10-12 Ga Splice Connector
Screw, 6-32 x .312 Pan Head
Label, Sensitivity Switch
Label, F1 Fuse Replacement
Insulator, Fuse Board
QTY
2
3
2
4
2
2
2
27
2
1
1
2
11
1
1
1
MISCELLANEOUS
CPN
A10110-70812
A10094-3
A10109-10822
A10192-1
C 6912-7
C 6913-5
C 6914-3
C 8812-7
C 1813-2
C 5894-8
D 7622-0
C 7351-7
C 9491-9
D 7784-8
D 8251-7
D 8069-4
18
Micro-Tech 2400 Amplifier Service Manual
Module Information
MODULE HISTORY
The Micro Tech 2400 amplifier was introduced in
January of 1995. Since then there have been several
updates and revisions, some of which called for new
modules. The following is a list of all modules used up
to this date, July 1995.
OUTPUT MODULES: (left and right are identical)
Q43354-2
Original Output Module, still in production. Uses
P10429-2 board.
MAIN MODULES:
Q43328-6
Original Main Module on D 8679-9 board. Used until
6-14-95.
Q43399-7
Main Module on D 8827-4 board.
FUSE MODULE:
M46330-3
Fuse board on P10425-0 board.
DISPLAY MODULE:
Q43327-8
Display module on D 8030-5 board.
19
Micro-Tech 2400 Amplifier Service Manual
M46330-3 Fuse Module & Q43327-8 Display Module Parts List
M46330-3 FUSE MODULE
2
11
1
C 5060-6
C 7817-7
P10425-0
PC Mount Fuse Clip
Tab, AMP .25 Faston PC Mount
MT-2400 Fuse Board
For replacement fuse see Power Supply Parts List on page 16.
Q43327-8 DISPLAY MODULE
CAPACITORS
C503
C507
C701
C702
C603
C607
C 6806-1
C 6809-5
C 6802-0
C 6802-0
.01µF
220pF
.47µF
.47µF
C 3533-4
C 3533-4
1N966B
1N966B
C 4342-9
C 4342-9
Amber, MV5153
Amber, MV5153
C 4508-5
Socket, IC DIP 16 Pin
DIODES
D701
D702
LED'S
E502
E701
E602
CONNECTOR
J3
TRANSISTORS
Q504
Q604
C 3625-8
2N4125
A10266-1351
A10266-7551
A10266-4751
A10266-4741
A10266-2221
A10266-1522
A10266-1001
A10266-1522
A10266-5111
A10266-5111
1.3M
7.5M
4.7M
470K
2.2K
1.5K .5W
10 Ohm
1.5K .5W
510 Ohm
510 Ohm
RESISTORS
R508
R509
R510
R511
R512
R513
R514
R702
R707
R608
R609
R610
R611
R612
R613
R614
R615
INTEGRATED CIRCUITS
U502
C 5070-5
TL072CP
D 8030-5
MT Display Board
BOARD
1
20
Micro-Tech 2400 Amplifier Service Manual
Q43354-2 Output Module Parts List (P10429-2 Board)
Q43354-2 Output Module for MT-2400. For Schematic See
J0658-5
CAPACITORS
C01
C02
C03
C04
C05
C06
C07
C08
C09
C43
C 8511-5
C 8426-6
C 8426-6
C 6806-1
C 6806-1
C 6806-1
C 6807-9
C 6810-3
C 6809-5
C 7697-3
.047µF
.1µF
.1µF
.01µF
.01µF
.01µF
.001µF
180pF
220pF
.01µF 500V
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2941-0
C 2941-0
C 2941-0
C 2941-0
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
1N4004
1N4004
1N4004
1N4004
1N5402
1N5402
1N5402
1N5402
1N4004
1N4004
1N4004
1N4004
1N4004
1N4004
C 6592-6
C 3510-2
C 3510-2
Output Coil
470µH
470µH
DIODES
D01
D02
D03
D04
D05
D06
D07
D08
D09
D10
D11
D12
D13
D14
INDUCTORS
L00
L01
L02
R00
R01
R02
R03
R04
R05
R06
R07
R08
R09
R10
R11
R12
R13
R14
R15
R16
R17
R18
R19
R20
R21
R22
R23
R24
R25
R26
R27
R28
R29
R30
R41
R42
R43
A10266-7501
A10266-1011
C 7778-1
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 7779-9
A10266-1011
C 7317-8
A10266-2R74
A10266-7501
A10266-2R74
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 6486-2
C 7778-1
C 7779-9
C 6844-2
A10266-1331
A10266-2221
C 6844-2
A10266-3911
A10266-1331
A10266-5101
A10265-10201
A10266-2201
A10266-2201
A10266-2201
75
100
5.6 flame proof
.2 5W
.2 5W
.2 5W
.2 5W
.2 5W
.2 5W
22 flame proof
100
2.7 5W
2.7 2W
75
2.7 2W
.2 5W
.2 5W
.2 5W
.2 5W
.2 5W
.2 5W
5.6 flame proof
22 flame proof
250 Pot LS Bias
13K
2.2K
250 Pot HS Bias
390
13K
51
102
22
22
22
P10429-2
C 5868-2
D 6414-3
C 9828-2
0 Ohm Jumper (11)
Q17/19 Hold Down
12 Pin Header
MISC.
TRANSISTORS
Q17
Q19
RESISTORS
C 8508-1
C 8509-9
NPN 2SC3298B
PNP 2SA1306B
Note: Q18, S100/200, Driver and Output Transistors
are not included with the module. See the Output
Assembly Parts List on pages 16 & 17.
Board
Jumpers
Clips
P500 P600
21
Micro-Tech 2400 Amplifier Service Manual
Q43328-6 Main Module Parts List (D8679-9 Board)
Q43328-6 MT-2400 ORIGINAL MAIN MODULE
Use Schematic J 0658-5
CAPACITORS
C1
C2
C4
C5
C6
C7
C8
C100
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
C112
C113
C114
C115
C116
C117
C118
C119
C122
C123
C124
C129
C130
C132
C133
C134
C135
C136
C137
C138
C139
C140
C141
C144
C145
C146
C147
C148
C149
C150
22
C200
C201
C202
C203
C204
C205
C206
C207
C208
C209
C210
C212
C213
C214
C215
C216
C217
C218
C219
C222
C223
C224
C229
C230
C232
C233
C234
C235
C236
C237
C238
C239
C240
C241
C244
C245
C246
C247
C248
C249
C250
C 3913-8
C 3913-8
C 6802-0
C 6806-1
C 6806-1
C 8897-8
C 5362-6
C 5311-3
C 9464-6
C 8576-8
C 6805-3
C 6805-3
C 6812-9
C 6812-9
C 8897-8
C 6814-5
C 8576-8
C 5362-6
C 9991-8
C 9992-6
C 8854-9
C 8854-9
C 9992-6
C 9991-8
C 6814-5
C 6802-0
C 6811-1
C 6812-9
C 6812-9
C 6814-5
C 6813-7
C 6806-1
C 6813-7
C 6805-3
C 6805-3
C 6808-7
C 6808-7
C 6813-7
C 6813-7
C 6812-9
C 6812-9
C 8576-8
C 6812-9
C 6812-9
C 6806-1
C 6810-3
C 6808-7
C 6806-1
470µF
470µF
.47µF
.01µF
.01µF
.1µF
2.2uF
22µF
10pF
100uF
.022µF
.022µF
47pF
47pF
.1µF
12pF
100µF
2.2µF
1µF
47µF
100µF
100µF
47µF
1µF
12pF
.47µF
100pF
47pF
47pF
12pF
27pF
.01µF
27pF
.022µF
.022µF
470pF
470pF
27pF
27pF
47pF
47pF
100µF
47pF
47pF
.01µF
180pF
470pF
.01µF
C151
C152
C153
C154
C155
C156
C158
C159
C160
C161
C251
C252
C253
C254
C255
C256
C258
C259
C260
C261
C 6806-1
C 6950-7
C 8897-8
A10434-104JD
C 8897-8
C 8897-8
C 6805-3
C 6805-3
C 8897-8
C 8897-8
.01µF
82pF 5%
.1µF
.1µF 250V
.1µF
.1µF
.022uF
.022uF
.1uF
.1uF
D200
D201
D202
D203
D204
D208
D209
D210
D211
D212
D213
D220
D221
D222
D223
D224
D225
D226
D227
D228
D229
D230
D231
D232
D233
D234
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 3181-2
C 3181-2
C 3824-7
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 5061-4
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 5061-4
C 3181-2
C 3181-2
C 5061-4
C 5061-4
C 5061-4
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
1N4004
1N4004
1N4004
1N4004
1N4004
1N4004
1N4004
1N4148
1N4148
1N970B
1N4148
1N4148
1N4148
1N4148
1N4148
1N3070
1N4148
1N4148
1N4148
1N4148
1N4148
1N3070
1N4148
1N4148
1N3070
1N3070
1N3070
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
E200
E201
C 9857-1
C 9857-1
RED
RED
DIODES
D1
D2
D3
D4
D5
D6
D7
D100
D101
D102
D103
D104
D108
D109
D110
D111
D112
D113
D120
D121
D122
D123
D124
D125
D126
D127
D128
D129
D130
D131
D132
D133
D134
LED's
E100
E101
Micro-Tech 2400 Amplifier Service Manual
Q43328-6 Main Module Parts List Cont. (D8679-9 Board)
RESISTOR NETWORKS
N101
N102
N201
N202
D 7944-8
D 6082-8
Res. Net.
Res. Net.
D 2961-7
C 3578-9
C 3810-6
C 3786-8
C 3578-9
C 3625-8
C 3786-8
C 5891-4
D 2961-7
C 3810-6
C 3625-8
C 3625-8
D 2962-5
C 3786-8
D 2961-7
D 2961-7
C 3625-8
C 3625-8
C 7458-0
C 3625-8
C 3786-8
C 5891-4
C 3625-8
C 7458-0
C 3625-8
C 7458-0
C 3625-8
C 3625-8
C 3625-8
C 3625-8
C 7458-0
C 7458-0
C 3625-8
2N3859A
MPSA93
MPSA43
PN4250
MPSA93
2N4125
PN4250
MTS105
2N3859A
MPSA43
2N4125
2N4125
MPS8097
PN4250
2N3859A
2N3859A
2N4125
2N4125
2N4123
2N4125
PN4250
MTS105
2N4125
2N4123
2N4125
2N4123
2N4125
2N4125
2N4125
2N4125
2N4123
2N4123
2N4125
A10265-53621
C 7340-0
C 7340-0
A10265-46421
OPEN
A10266-4331
A10265-75021
OPEN
A10265-75021
A10266-4331
C 7409-3
53.6K 1%
24 5W
24 5W
46.4K 1%
TRANSISTORS
Q100
Q101
Q102
Q103
Q105
Q106
Q107
Q108
Q109
Q110
Q112
Q113
Q115
Q116
Q117
Q118
Q119
Q120
Q123
Q124
Q125
Q126
Q127
Q128
Q129
Q130
Q131
Q132
Q133
Q134
Q135
Q136
Q137
Q200
Q201
Q202
Q203
Q205
Q206
Q207
Q208
Q209
Q210
Q212
Q213
Q215
Q216
Q217
Q218
Q219
Q220
Q223
Q224
Q225
Q226
Q227
Q228
Q229
Q230
Q231
Q232
Q233
Q234
Q235
Q236
Q237
RESISTORS
R1
R2
R3
R4
R5
R7
R8
R10
R17
R18
R100
R200
43K
75K 1%
75K 1%
43K
5K Lin. Vol.
R101
R102
R103
R104
R105
R106
R107
R108
R109
R110
R111
R112
R113
R114
R115
R116
R117
R118
R119
R120
R121
R122
R123
R124
R125
R126
R127
R128
R129
R130
R131
R132
R133
R134
R135
R136
R137
R138
R139
R140
R141
R142
R143
R144
R145
R146
R147
R148
R149
R150
R151
R152
R201
R202
R203
R204
R205
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R219
R220
R221
R222
R223
R224
R225
R226
R227
R228
R229
R230
R231
R232
R233
R234
R235
R236
R237
R238
R239
R240
R241
R242
R243
R244
R245
R246
R247
R248
R249
R250
R251
R252
A10265-49911
A10266-5111
A10265-10031
A10266-2721
A10266-2721
A10266-1231
A10266-6831
A10265-80601
A10266-5601
A10266-6831
A10266-1231
A10266-5131
A10266-4721
A10266-4721
A10266-3341
A10266-2751
A10265-46421
A10265-28701
A10265-68101
A10265-28701
C 5062-2
A10266-2741
A10266-2732
A10266-6821
C 8836-6
C 8836-6
A10266-6821
A10266-1331
A10265-10031
A10265-10031
A10266-1331
C 5062-2
A10266-2741
A10266-2732
A10266-1012
A10266-6821
A10266-1012
A10266-6821
A10265-80601
A10266-5601
A10266-1541
A10266-1541
A10266-4711
A10266-4711
A10266-4711
A10266-1231
C 8836-6
A10266-2721
C 8836-6
A10266-2721
A10266-1231
A10265-11521
4.99K 1%
510
100K 1%
2.7K
2.7K
12K
68K
806
56
68K
12K
51K
4.7K
4.7K
330K
2.7M
46.4K 1%
287 1%
681 1%
287 1%
100K Pot
270K
27K .5W
6.8K
100 .5W FP
100 .5W FP
6.8K
13K
100K 1%
100K 1%
13K
100K Pot
270K
27K .5W
100 .5W
6.8K
100 .5W
6.8K
806 1%
56
150K
150K
470
470
470
12K
100 .5W FP
2.7K
100 .5W FP
2.7K
12K
11.5K 1%
23
Micro-Tech 2400 Amplifier Service Manual
Q43328-6 Main Module Parts List Cont. (D8679-9 Board)
R153
R154
R155
R156
R157
R158
R159
R160
R161
R162
R163
R164
R165
R166
R167
R168
R170
R171
R173
R174
R175
R176
R177
R179
R180
R181
R182
R184
R186
R187
R188
R189
R190
R193
R194
R195
R196
R197
R198
R199
R300
R301
R911
R912
R913
R914
R915
R916
R917
R918
R919
R920
24
R253
R254
R255
R256
R257
R258
R259
R260
R261
R262
R263
R264
R265
R266
R267
R268
R270
R271
R273
R274
R275
R276
R277
R279
R280
R281
R282
R284
R286
R287
R288
R289
R290
R293
R294
R295
R296
R297
R298
R299
R400
R401
R1011
R1012
R1013
R1014
R1015
R1016
R1017
R1018
R1019
R1020
A10124-24
A10266-5601
A10266-1321
A10266-1321
A10266-1321
A10265-11321
A10265-10011
A10266-5601
A10266-4701
A10266-4701
A10266-5601
A10266-4711
A10266-4711
A10266-4711
A10265-10011
A10265-10011
A10265-10011
A10265-10011
A10266-5601
A10265-24921
A10265-78711
A10265-24921
A10265-19121
A10266-1321
A10266-4711
A10266-4721
A10266-2201
A10266-4741
A10266-2751
A10266-3321
A10266-3321
A10266-2731
A10266-2051
A10265-10021
A10265-10031
A10266-3021
A10266-4721
A10265-10021
A10266-4721
A10265-10021
A10265-10031
A10265-10031
A10266-1521
A10266-4711
A10265-10031
A10266-5141
A10266-2201
A10266-2201
A10266-10021
A10266-10021
A10266-10021
A10266-10021
JUMPER
56
1.3K
1.3K
1.3K
11.3K
1K 1%
56
47
47
56
470
470
470
1K 1%
1K 1%
1K 1%
1K 1%
56
24.9K 1%
7.87K 1%
24.9K 1%
19.1K 1%
1.3K
470
4.7K
22
470K
2.7M
3.3K
3.3K
27K
2M
10K 1%
100K 1%
3K
4.7K
10K 1%
4.7K
10K 1%
100K 1%
100K 1%
1.5K
470
100K 1%
510K
22
22
10K
10K
10K
10K
R921
R922
R923
R924
R925
R926
R927
R928
R929
R930
R931
R932
R933
R934
R935
R936
R937
R938
R939
R940
R941
R942
R1021
R1022
R1023
R1024
R1025
R1026
R1027
R1028
R1029
R1030
R1031
R1032
R1033
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
C 9079-2
A10265-68101
A10265-35711
A10265-60401
A10265-10031
A10265-60401
A10265-10031
A10265-35711
A10266-1241
A10266-1241
A10266-3921
A10265-10021
A10266-4731
A10265-10021
A10266-4731
A10265-10021
A10265-10021
A10265-10021
A10266-4731
A10266-4731
A10266-4731
A10266-4731
200 Pot
681 1%
3.57K 1%
604 1%
100K 1%
604 1%
100K 1%
3.57K 1%
120K
120K
3.9K
10K 1%
47K
10K 1%
47K
10K 1%
10K 1%
10K 1%
47K
47K
47K
47K
C 7325-1
C 7960-5
C 6781-6
Ground Lift
Sensitivity
Stereo/Mon
C 6564-6
HDR
SWITCHES
S2
S3
S4
TEST POINTS
TP1
TP2
INTEGRATED CIRCUITS
U1
U2
U100
U101
U102
U103
U104
U200
U201
U202
U203
U204
C 5095-2
C 5096-0
C 6911-9
C 6411-0
C 4345-2
C 6910-1
C 7558-7
UA7815
UA7915
UPA75
H11C2
LM339
UPA76
MC33079P
Board
Socket
U1X, U2X
HW1-4
HW5-9
J1
J2
J11
J100 J200
Cover
D 8679-9
C 3450-1
C 9494-3
C 8812-7
C 9944-7
C 7593-4
C 4508-5
C 7526-4
C 6777-4
C 6778-2
14 Pin (4)
Heatsinks
5.5" Cbl Tie
Nyl. Spacer
5 Pin HDR
16 Pin
3 Pin HDR
Ph Jack, (2)
Ph Jk CVR
MISC.
Micro-Tech 2400 Amplifier Service Manual
Q43328-6 Main Module Parts List Cont. (D8679-9 Board)
J500 J800
J600 J700
HW5-8
Z1-Z5
D 8681-5
D 8680-7
C 8812-7
OPEN
10 In. RBN
6 In. RBN
5.5" Cbl Tie
25
Micro-Tech 2400 Amplifier Service Manual
Q43399-7 Main Module Parts List (D8827-4 Board)
Q43399-7 MT-2400 MAIN MODULE
Use Schematic J 0691-6
CAPACITORS
C1
C2
C4
C5
C6
C7
C8
C100
C101
C102
C103
C104
C105
C106
C107
C108
C109
C110
C112
C113
C114
C115
C116
C117
C118
C119
C122
C123
C124
C129
C130
C133
C134
C135
C136
C137
C138
C139
C140
C141
C144
C145
C146
C147
C148
C149
C150
C151
26
C200
C201
C202
C203
C204
C205
C206
C207
C208
C209
C210
C212
C213
C214
C215
C216
C217
C218
C219
C222
C223
C224
C229
C230
C233
C234
C235
C236
C237
C238
C239
C240
C241
C244
C245
C246
C247
C248
C249
C250
C251
C 3913-8
C 3913-8
C 6802-0
C 6806-1
C 6806-1
C 8897-8
C 5362-6
C 5311-3
C 9464-6
C 8576-8
C 6805-3
C 6805-3
C 6812-9
C 6812-9
C 8897-8
C 6814-5
C 8576-8
C 5362-6
C 8991-9
C 8996-9
C 8854-9
C 8854-9
C 8986-9
C 8991-9
C 6814-5
C 6802-0
C 6811-1
C 6812-9
C 6812-9
C 6814-5
C 6813-7
C 6813-7
C 6805-3
C 6805-3
C 6808-7
C 6808-7
C 6813-7
C 6813-7
C 6812-9
C 6812-9
C 8576-8
C 6812-9
C 6812-9
C 6806-1
C 6810-3
C 6808-7
C 6806-1
C 6806-1
470µF
470µF
.47µF
.01µF
.01µF
.1µF
2.2uF
22µF
10pF
100uF
.022µF
.022µF
47pF
47pF
.1µF
12pF
100µF
2.2µF
.47µF
15µF
100µF
100µF
15µF
.47µF
12pF
.47µF
100pF
47pF
47pF
12pF
27pF
27pF
.022µF
.022µF
470pF
470pF
27pF
27pF
47pF
47pF
100µF
47pF
47pF
.01µF
180pF
470pF
.01µF
.01µF
C152
C153
C154
C155
C156
C158
C159
C160
C161
C113X
C116X
C252
C253
C254
C255
C256
C258
C259
C260
C261
C213X
C216X
C 6950-7
C 8897-8
A10434-104JD
C 8897-8
C 8897-8
C 6805-3
C 6805-3
C 8897-8
C 8897-8
OPEN
OPEN
82pF 5%
.1µF
.1µF 250V
.1µF
.1µF
.022uF
.022uF
.1uF
.1uF
D200
D201
D202
D203
D204
D205
D206
D208
D209
D210
D211
D212
D213
D220
D221
D222
D223
D224
D225
D226
D227
D228
D229
D230
D231
D232
D233
D234
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 2851-1
C 3181-2
C 3181-2
C 3824-7
C 3181-2
C 3181-2
C 2851-1
C 2851-1
C 3181-2
C 3181-2
C 3181-2
C 5061-4
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 5061-4
C 3181-2
C 3181-2
C 5061-4
C 5061-4
C 5061-4
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
C 3181-2
1N4004
1N4004
1N4004
1N4004
1N4004
1N4004
1N4004
1N4148
1N4148
1N970B
1N4148
1N4148
1N4004
1N4004
1N4148
1N4148
1N4148
1N3070
1N4148
1N4148
1N4148
1N4148
1N4148
1N3070
1N4148
1N4148
1N3070
1N3070
1N3070
1N4148
1N4148
1N4148
1N4148
1N4148
1N4148
E200
E201
C 9857-1
C 9857-1
RED
RED
DIODES
D1
D2
D3
D4
D5
D6
D7
D100
D101
D102
D103
D104
D105
D106
D108
D109
D110
D111
D112
D113
D120
D121
D122
D123
D124
D125
D126
D127
D128
D129
D130
D131
D132
D133
D134
LED's
E100
E101
Micro-Tech 2400 Amplifier Service Manual
Q43399-7 Main Module Parts List Cont. (D8827-4 Board)
RESISTOR NETWORKS
N101
N102
N201
N202
D 7944-8
D 6082-8
Res. Net.
Res. Net.
D 2961-7
C 3578-9
C 3810-6
C 3786-8
C 3578-9
C 3625-8
C 3786-8
C 5891-4
D 2961-7
C 3810-6
C 3625-8
C 3625-8
D 2962-5
C 3786-8
D 2961-7
D 2961-7
C 3625-8
C 3625-8
C 7458-0
C 3625-8
C 3786-8
C 5891-4
C 3625-8
C 7458-0
C 3625-8
C 7458-0
C 3625-8
C 3625-8
C 3625-8
C 3625-8
C 7458-0
C 7458-0
C 3625-8
C 3810-6
C 3578-9
2N3859A
MPSA93
MPSA43
PN4250
MPSA93
2N4125
PN4250
MTS105
2N3859A
MPSA43
2N4125
2N4125
MPS8097
PN4250
2N3859A
2N3859A
2N4125
2N4125
2N4123
2N4125
PN4250
MTS105
2N4125
2N4123
2N4125
2N4123
2N4125
2N4125
2N4125
2N4125
2N4123
2N4123
2N4125
MPSA42
MPSA93
A10265-53621
C 7340-0
C 7340-0
A10265-46421
OPEN
A10266-4331
A10265-75021
OPEN
OPEN
53.6K 1%
24 5W
24 5W
46.4K 1%
TRANSISTORS
Q100
Q101
Q102
Q103
Q105
Q106
Q107
Q108
Q109
Q110
Q112
Q113
Q115
Q116
Q117
Q118
Q119
Q120
Q123
Q124
Q125
Q126
Q127
Q128
Q129
Q130
Q131
Q132
Q133
Q134
Q135
Q136
Q137
Q138
Q139
Q200
Q201
Q202
Q203
Q205
Q206
Q207
Q208
Q209
Q210
Q212
Q213
Q215
Q216
Q217
Q218
Q219
Q220
Q223
Q224
Q225
Q226
Q227
Q228
Q229
Q230
Q231
Q232
Q233
Q234
Q235
Q236
Q237
Q238
Q239
RESISTORS
R1
R2
R3
R4
R5
R7
R8
R10
R11
43K
75K 1%
R12
R17
R18
R100
R101
R102
R103
R104
R105
R106
R107
R108
R109
R110
R111
R112
R113
R114
R115
R116
R117
R118
R119
R120
R121
R122
R123
R124
R125
R126
R127
R128
R129
R130
R131
R132
R133
R134
R135
R136
R137
R138
R139
R140
R141
R142
R143
R144
R145
R146
R147
R148
R200
R201
R202
R203
R204
R205
R206
R207
R208
R209
R210
R211
R212
R213
R214
R215
R216
R217
R218
R219
R220
R221
R222
R223
R224
R225
R226
R227
R228
R229
R230
R231
R232
R233
R234
R235
R236
R237
R238
R239
R240
R241
R242
R243
R244
R245
R246
R247
R248
OPEN
A10265-75021
A10266-4331
C 7409-3
A10265-49911
A10266-5111
A10265-10031
A10266-2721
A10266-2721
A10266-1231
A10266-6831
A10265-80601
A10266-5601
A10266-6831
A10266-1231
A10266-5131
A10266-4721
A10266-4721
A10266-3341
A10266-2751
A10265-46421
A10265-28701
A10265-68101
A10265-28701
C 5062-2
A10266-2741
A10266-2732
A10266-6821
C 8836-6
C 8836-6
A10266-6821
A10266-1331
A10265-10031
A10265-10031
A10266-1331
C 5062-2
A10266-2741
A10266-2732
C 8836-6
A10266-6821
C 8836-6
A10266-6821
A10265-80601
A10266-5601
A10266-1541
A10266-1541
A10266-4711
A10266-4711
A10266-4711
A10266-1231
C 8836-6
A10266-2721
75K 1%
43K
5K Lin. Pot.
4.99K 1%
510
100K 1%
2.7K
2.7K
12K
68K
806
56
68K
12K
51K
4.7K
4.7K
330K
2.7M
46.4K 1%
287 1%
681 1%
287 1%
100K Pot
270K
27K .5W
6.8K
100 .5W FP
100 .5W FP
6.8K
13K
100K 1%
100K 1%
13K
100K Pot
270K
27K .5W
100 .5W FP
6.8K
100 .5W FP
6.8K
806 1%
56
150K
150K
470
470
470
12K
100 .5W FP
2.7K
27
Micro-Tech 2400 Amplifier Service Manual
Q43399-7 Main Module Parts List Cont. (D8827-4 Board)
R149
R150
R151
R152
R153
R154
R155
R156
R157
R158
R159
R160
R161
R162
R163
R164
R165
R166
R167
R168
R169
R170
R171
R172
R173
R174
R175
R176
R177
R179
R180
R181
R182
R184
R186
R187
R188
R189
R190
R193
R194
R195
R196
R197
R198
R199
R300
R301
R911
R912
R913
R914
28
R249
R250
R251
R252
R253
R254
R255
R256
R257
R258
R259
R260
R261
R262
R263
R264
R265
R266
R267
R268
R269
R270
R271
R272
R273
R274
R275
R276
R277
R279
R280
R281
R282
R284
R286
R287
R288
R289
R290
R293
R294
R295
R296
R297
R298
R299
R400
R401
R1011
R1012
R1013
R1014
C 8836-6
A10266-2721
A10266-1231
A10265-11521
A10124-24
A10266-5601
A10266-1321
A10266-1321
A10266-1321
A10265-11321
A10265-10011
A10266-5601
A10266-4701
A10266-4701
C10166-4
A10266-4711
A10266-4711
A10266-4711
A10265-10011
A10265-10011
OPEN
A10265-10011
A10265-10011
OPEN
C10166-4
A10265-24921
A10265-78711
A10265-24921
A10265-19121
A10266-1321
A10266-4711
A10266-4721
A10266-2201
A10266-4741
A10266-2751
A10266-3321
A10266-3321
A10266-2731
A10266-2051
A10266-1031
A10265-10031
A10266-3021
A10266-4721
A10265-10021
A10266-4721
A10265-10021
A10265-10031
A10265-10031
A10266-1521
A10266-4711
A10266-1041
A10266-5141
100 .5W FP
2.7K
12K
11.5K 1%
JUMPER
56
1.3K
1.3K
1.3K
11.3K
1K 1%
56
47
47
56 FP
470
470
470
1K 1%
1K 1%
1K 1%
1K 1%
56
24.9K 1%
7.87K 1%
24.9K 1%
19.1K 1%
1.3K
470
4.7K
22
470K
2.7M
3.3K
3.3K
27K
2M
10K
100K 1%
3K
4.7K
10K 1%
4.7K
10K 1%
100K 1%
100K 1%
1.5K
470
100K
510K
R915
R916
R917
R918
R919
R920
R921
R922
R923
R924
R925
R926
R927
R928
R929
R930
R931
R932
R933
R934
R935
R936
R937
R938
R939
R940
R941
R942
R943
R944
R945
R946
R947
R1015
R1016
R1017
R1018
R1019
R1020
R1021
R1022
R1023
R1024
R1025
R1026
R1027
R1028
R1029
R1030
R1031
R1032
R1033
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1042
R1043
R1044
R1045
R1046
R1074
A10266-2201
A10266-2201
A10266-10021
A10266-10021
A10266-10021
A10266-10021
C 9079-2
A10265-68101
A10265-35711
A10265-60401
A10266-1041
A10265-60401
A10266-1041
A10265-35711
A10266-1241
A10266-1241
A10266-3921
A10266-1031
A10266-4731
A10266-1031
A10266-4731
A10266-1031
A10266-1031
A10266-1031
A10266-4731
A10266-4731
A10266-4731
A10266-4731
A10266-1031
A10266-1031
A10266-4701
A10266-2031
A10266-2031
22
22
10K
10K
10K
10K
200 Pot
681 1%
3.57K 1%
604 1%
100K
604 1%
100K
3.57K 1%
120K
120K
3.9K
10K
47K
10K
47K
10K
10K
10K
47K
47K
47K
47K
10K
10K
47
20K
20K
C 7325-1
C 7960-5
C 6781-6
Gnd Lift
Sensitivity
Stereo/Mon
C 6564-6
HDR
SWITCHES
S2
S3
S4
TEST POINTS
TP1
TP2
INTEGRATED CIRCUITS
U1
U2
U100
U101
U102
U103
U104
U100A
U200
U201
U202
U203
U204
U200A
C 5095-2
C 5096-0
C 6911-9
C 6411-0
C 4345-2
C 6910-1
C 7558-7
OPEN
UA7815
UA7915
UPA75
H11C2
LM339
UPA76
MC33079P
Micro-Tech 2400 Amplifier Service Manual
Q43399-7 Main Module Parts List Cont. (D8827-4 Board)
U103A U203A
OPEN
MISC.
Board
Socket
HW9-10
HW11-15
J1
J2
J11
J12
J100 J200
Cover
J101 J201
J500 J800
J600 J700
HW5-8
Z1-Z5
D 8827-4
C 3450-1
C 9494-3
C 9944-7
C 7593-4
C 4508-5
C 7526-4
Not Used
C 6777-4
C 6778-2
Not Used
D 8681-5
D 8680-7
C 8812-7
OPEN
14 Pin
Heatsinks
Nyl. Spacer
5 Pin HDR
16 Pin
3 Pin HDR
Ph. Jack
Ph Jk CVR
10 In. RBN
6 In. RBN
5.5" Tie, (4)
29