APW Wyott FD-48H Operating instructions

R
INSTALLATION AND OPERATING INSTRUCTIONS
Electric Griddles
Models: EG-24H, -36H & -48H
IMPORTANT FOR FUTURE REFERENCE
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or Parts, this information is required.
Model Number
Serial Number
Date Purchased
CONTENTS
General Information
Safety Precautions
Specifications & Dimensions
Installation
Equipment Preparation
Operator Seasoning
Cleaning
Suggested Temperatures & Times For Griddling
Parts List
Exploded View
Wiring Diagrams
Warranty
2
3
3
4
4
4
5
6
6
7
8
11
!
WARNING: For your safety do not store or use gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI
Z83.14B, 1991)
!
!
WARNING: Improper installation, operation, service or maintenance can cause property
damage, injury or death. Read and understand these instructions thoroughly before
positioning, installing, maintaining or servicing this equipment.
!
P/N 8806040 1/08
APW WYOTT Foodservice Equipment Company
P.O. Box 1829
Cheyenne, WY 82003
+1 (307) 634-5801 Phone
+1(307) 637-8071 Fax
+1 (800) 752-0863 Toll Free
www.apwwyott.com
1
GENERAL INFORMATION
THIS MANUAL SHOULD BE RETAINED FOR FUTURE REFERENCE
!
CAUTION: These models are designed, built, and sold for commercial use. If these models are
positioned so the general public can use the equipment, make sure that cautions, warnings, and
operating instructions are clearly posted near each unit so that anyone using the equipment will
use it correctly and not injure themselves or harm the equipment.
!
WARNING: Improper installation, operation, service or maintenance can cause property damage,
injury or death. Read and understand these instructions thoroughly before positioning, installing,
maintaining or servicing this equipment.
!
!
WARNING: Install per the spacing requirements listed in the installation section of this manual. We
strongly recommend having a competent professional install the equipment. A licensed electrician
should make the electrical connections and connect power to the unit. Local codes should always
be used when connecting these units to electrical power. In the absence of local codes, use the
latest version of the National Electrical Code.
!
!
WARNING: For your safety do not store or use gasoline or other flammable vapors or liquids in the
vicinity of this or any other appliance. Keep the area free and clear of combustibles. (See ANZI
Z83.14B, 1991)
!
WARNING: Check the data plate on this unit before installation. Connect the unit only to the voltage
and frequency listed on the data plate. Connect only to 1 or 3 phase as listed on the data plate.
!
!
WARNING: This product is intended for commercial use only. Not for household use Retain this
manual for future reference Oven must be kept clear of combustibles at all times
!
!
WARNING: SHOCK HAZARD - Do not open any panels that require the use of tools.
!
!
WARNING: Electrical and grounding connections must comply with the applicable portions of the
national electrical code and/or other local electrical codes.
!
!
WARNING: Disconnect device from electrical power supply and place a Tag Out-Lockout on the
power plug, indicating that you are working on the circuit.
!
!
NOTICE: This product is intended for commercial use only. Not for household use.
!
!
NOTICE: The unit when installed, must be electrically grounded and comply with local codes, or in
the absence of local codes, with the national electrical code ANSI/NFPA70- latest edition.
Canadian installation must comply with CSA-STANDARD C.22.2 Number 0 M1982 General
Requirements-Canadian Electrical Code Part II, 109-M1981- Commercial Cooking Appliances.
!
!
NOTICE: Local codes regarding installation vary greatly from one area to another. The National
Fire Protection Association, Inc. states in its NFPA96 latest edition that local codes are “Authority
Having Jurisdiction” when it comes to requirement for installation of equipment. Therefore,
installation should comply with all local codes.
!
!
WARNING: An earthing cable must connect the appliance to all other units in the complete
installation and from there to an independent earth connection.
!
!
NOTICE: Maintenance and repair should be handled by a factory authorized agent. Before doing
any maintenance or repair, contact APW Wyott.
!
!
2
!
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure everyone involved in its operation is fully trained and
is aware of all precautions. Accidents and problems can result by a failure to follow fundamental rules and
precautions.
The following words and symbols, found in this manual, alert you to hazards to the operator, service
personnel or the equipment. The words are defined as follows.
!
DANGER: This symbol warns of imminent hazard which will result in serious injury or
death.
!
!
WARNING: This symbol refers to a potential hazard or unsafe practice, which could result
in serious injury or death.
!
!
CAUTION: This symbol refers to a potential hazard or unsafe practice, which may result in
minor or moderate injury or product or property damage.
!
!
NOTICE: This symbol refers to information that needs special attention or must be fully
understood even though not dangerous.
!
IMMEDIATELY INSPECT FOR SHIPPING DAMAGE
All containers should be examined for damage before and during unloading. The freight carrier has
assumed responsibility for its safe transit and delivery. If equipment is received damaged, either apparent
or concealed, a claim must be made with the delivering carrier.
A) Apparent damage or loss must be noted on the freight bill at the time of delivery. It must then be signed
by the carrier representative (Driver). If this is not done, the carrier may refuse the claim. The carrier can
supply the necessary forms.
B) Concealed damage or loss if not apparent until after equipment is uncrated, a request for inspection
must be made to the carrier within 15 days. The carrier should arrange an inspection. Be certain to hold all
contents and packaging material.
Installation and start-up should be performed by a qualified installer who thoroughly read, understands and
follows these instructions.
If you have questions concerning the installation, operation, maintenance or service of this product, write
Technical Service Department APW/Wyott Foodservice Equipment Company, P.O. Box 1829, Cheyenne,
WY 82003.
Congratulations on your purchase of APW Wyott commercial cooking or refrigeration equipment. APW
Wyott takes pride in the design and quality of our products. When used as intended and with proper care
and maintenance, you will experience years of reliable operation from this equipment. To ensure best
results, it is important that you read and follow the instructions in this manual carefully.
LOCATION OF DATA PLATE
The data plate is located on the front panel.
SPECIFICATIONS AND DIMENSIONS
Electrical
EG-24H,
EG-36H,
EG-48H,
208/240 Volt,
208/240 Volt,
208/240 Volt,
50/60 Hz,
50/60 Hz,
50/60 Hz,
1 Ph,
1 Ph,
1 Ph,
3
32.5/37.5 Amps
48.7/56.3 Amps
65/75 Amps
Dimensions Overall Dimensions with 4" Legs
EG-24H
15-1/2"H x 25-3/4"D x 24"W
EG-36H
15-1/2"H x 25-3/4"D x 36" W
EG-48H
15-1/2"H x 25-3/4"D x 48"W
Ship Weight
EG-24H
180 lbs
EG-36H
267 lbs
EG-48H
342 lbs
INSTALLATION
Always clean equipment thoroughly before the first use. Check rating label for your model designation and
electrical rating. For best results, use stainless steel countertops. Attach legs to units.
Uncrate the griddle and place it in the approximate operation location. Make sure no parts are discarded
with crating material Remove the bottom cover for wiring junction box access at the back of the griddle.
!
WARNING: This device should be safely and adequately grounded in accordance with
local codes, or in the absence of local codes, with the National Electrical code,
ANSI/NFPA 70, Latest Edition to protect the user from electrical shock. It requires a
grounded system and a dedicated circuit, protected by a fuse or circuit breaker of proper
size and rating. Canadian installation must comply with the Canadian Electrical Code,
CSA C22.2, as applicable
!
This griddle is wired for 208 volt or 230 volt service. Proper installation should comply with the attached
rating plate containing model number, serial number, voltage and amperage. Supply power wiring through
rear electrical knock-out to terminal block in junction box according to the National Electrical Code.. Test for
proper voltage supply. Return the bottom cover and mounting screws). Screw the legs into the permanently
fastened nuts on four corners of the unit
Set the griddle upright in the operating location.
Leveling: a slight incline from the front to the back may be desired to eliminate standing oil. Adjust feet
accordingly.
EQUIPMENT PREPARATION
The griddle is shipped with protective coatings of oil and/or grease. Remove the griddle plate coating just
prior to its first cooking use. If the griddle is to be shut down for an extended period, put a heavy coat of clean
grease back over the griddle plate.
Wipe the remaining cabinet parts down with a hot, wet cloth to remove any shipping dust and protective oil.
Remove anything that may be in the grease drawer.
!
CAUTION: Care must be exercised not to overheat the griddle plate on initial start-up by
setting the controls above normal operating temperature. Overheating may cause the
plate to warp and will carbonize the grease (this will cause sticking).
!
OPERATING SEASONING
A new griddle surface must be seasoned to do a good cooking job. The metal surface of the griddle is
porous. Food tends to get trapped in these pores and stick; therefore, it is important to "season" or "fill up"
these pores with griddling "fat" before cooking on any metal surfaced griddle. Seasoning gives the surface
a slick, hard finish from which the food with release easily.
To season, heat the griddle to a low (300°F to 350°F) temperature and pour on a small amount of cooking
oil, about one ounce per square foot of surface. Spread the oil over the entire griddle surface with a cloth to
create a thin film. Wipe off any excess oil with a cloth.
Repeat the procedure 2 to 3 times until the griddle has a slick, mirror-like surface.
4
!
CAUTION: This griddle plate is steel, but the surface is relatively soft and can be scored or
dented by carelessly using a spatula. Be careful not to dent, scratch, or gouge the plate
surface. Do not try to knock off loose food that may be on the spatula by tapping the corner
or the edge of the spatula on the griddle surface.
!
The individual controls operate each 12" wide cooking zone and the signal lights indicate power is being
applied to the heaters. When the light is out, with the dial set on a temperature setting, the griddle plate has
reached the desired temperature. The lights will intermittently come on during cooking cycles to indicate
temperature is being maintained.
CLEANING
NEVER clean any electrical unit by immersing it in water. Turn unit off and allow it to cool down before
surface cleaning. Always clean equipment thoroughly before first use. Clean unit daily. Except where noted
on charts: use warm, soap water. Mild cleansers and PLASTIC scouring pads may be used to remove
baked on food and water scale on metal units. Unplug electrical units before cleaning or servicing. All
service should be performed by an American Wyott authorized service agency.
Empty the grease drawer daily. Clean the unit regularly. A clean unit looks better, lasts longer and performs
better.
KEEP GRIDDLE PLATE SURFACE CLEAN. To produce evenly cooked, perfectly browned griddle
products, keep the griddle free of carbonized grease.
Carbonized grease on the surface hinders the transfer of heat from the griddle surface to food. This results
in spotty browning and loss of cooking efficiency and, worst of all, carbonized grease tends to cling to the
griddled foods, giving them a highly unsatisfactory and unappetizing appearance. To keep the griddle clean
and operating at peak efficiency, follow these simple instructions.
AFTER EACH USE, clean the griddle with a wire brush or flexible spatula.
ONCE A DAY, thoroughly clean splash back, sides and front. Remove the grease drawer and chute, empty
and wash them out in the same manner as any ordinary cooking utensil.
ONCE A WEEK, clean the griddle surface thoroughly. If necessary, use a griddle stone, wire brush or steel
wool on the surface. Rub with the grain of the metal while the griddle is still warm. A detergent may be used
on the plate surface to help clean it, but care must be taken to be sure the detergent is thoroughly removed.
After removal of the detergent, the surface of the plate should then be covered with a thin film of oil to
prevent rusting. Clean stainless steel surfaces with a damp cloth and polish with a soft, dry cloth. To remove
discoloration, use a nonabrasive cleaner. After each "weekly" type of cleaning, the griddle must be
reseasoned. If the griddle usage is very high, consider going through the "weekly" cleaning procedures
more often than once a week.
FACTORY OFFSETS
TEMPERATURE (°F)
OFFSET (°F)
FACTORY OFFSET - APW GRIDDLE CONTROL
150
200
250
300
350
400
450
The control will come with the following offsets
built in. The control will interpolate the offset for
values between those shown in the adjacent chart.
3
-10
-16
-24
-33
-39
-45
POTENTIOMETER
MANUAL TEMPERATURE ADJUSTMENT
-10°F
A PCB located potentiometer allows a manual
Temperature Adjustment:
Warmer: Clockwise
Colder: Counter-clockwise
-20°F
5
0
- + +10°F
+20°F
SUGGESTED TEMPERATURES AND TIMES FOR GRIDDLING
FOOD
CONTROL SETTING
(FAHRENHEIT)
American fried potatoes
Bacon
Boiled ham
Beef tenderloin
Canadian bacon
Hamburgers
Club steak
Ham steak
Sausage links or patties
French toast
Pancakes
Scrambled eggs
Hard fried eggs
Soft fried eggs
Sunny side-up eggs
375°
350°
375°
400°
350°
350°
450°
400°
350°
400°
375°
300°
225° to 300°
250° to 300°
225° to 300°
TIME IN
MINUTES
3 to 4
6
2
5 to 7
3 to 4
3 to 4
3 to 5
10
3 to 4
4 to 5
2
3 to 4
3 to 4
2 to 3
3 to 4
NOTE: These are only suggested griddle temperatures and cooking times. You may want to
try others. For example, some restaurants are cooking hamburgers at 300°F and under.
PARTS LIST
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
*24
*25
26
27
28
29
*30
31
32
33
34
EG-24H
P/N
EG-36H
P/N
EG48H
P/N
Description
21823620
21820823
21823621
21823619
2425000
21823622
8705801
8632000
1514000
1481700
1481705
1439900
64256301
21707000
8436200
21820716
21706900
1481000
1107903
64257301
280700
21822038
21822049
8824624
8706225
30047501
21822036
21814628
21823624
1481710
3100712
8196700
21820826
21820827
21823720
21820923
21823721
21823719
2425000
21823722
8705801
8632000
1514000
1481700
1481705
1439900
64256301
21707000
8436200
21820716
21706901
1481000
1107203
64257301
280700
21822038
21822049
8824636
8706225
30047501
21822036
21814628
21823624
1481710
3100712
8196700
21820826
21820827
21823820
21821023
21823821
21823819
2425000
21823822
8705801
8632000
1514000
1481700
1481705
1439900
64256301
21707000
8436200
21820716
21706902
1481000
1107203
64257301
280700
21822038
21822049
8824648
8706225
30047501
21822036
21814628
21823624
1481710
3100712
8196700
21820826
21820827
Weldment, Griddle Plate
Support, Leg
Panel, Bottom
Panel, Control
Pan, Grease
Panel, Back
Knob, Control
Leg, 4" Adj.
Light, Indicator
Thermostat, Elec. Griddle
Potentiometer, Elec. Griddle
Element, Heating 240V
Plate, Pressure
Retainer, Insulation
Nut, Clamping
Side, Grease Chute
Insulation
Switch, High Limit
Terminal Block
Assy, Bulb Clamp
Plate, Inspection
Panel, Side EG-H
Panel, Side L.H.
Decal, Front Panel
Decal, Dial Plate
Guide, Grease Slide
Mount, Terminal Block
Mount, High Limit
Mount, Thermostat
Probe, Electric Griddle
U-Nut, #10
Screw, #10 X 3/4 AB
Cap, R.H.
Cap, L.H.
*NOT SHOWN
6
Quantity
1
2
1
1
1
1
2(24) 3(36) 4(48)
4
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
12(24) 18(36) 24(48)
28(24) 42(36) 56(48)
2
1
2(24) 3(36) 4(48)
1
2(24) 3(36) 4(48)
1
1
1
1
2(24) 3(36) 4(48)
2
1
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
2(24) 3(36) 4(48)
4
4
1
1
EXPLODED VIEW
111
12
12
2
16
16
2
13
13
2
17
17
1
20
20
2
14
14
12
23
23
1
11
2
11
32
32
4
441
31
31
4
19
19
1
18
2
18
29
29
2
34
34
1
9
2
9
15
15
32
222
28
28
2
772
27
27
1
22
22
1
21
21
1
10
10
2
33
32
33
1
32
4
331
884
26
26
2
550
7
661
WIRING DIAGRAMS
MODEL EG-24H VOLTS: 208/240 HZ: 50/60 PH: 1/3
4.5 KW Element
NOMINAL AMPS/LINE
Total KW
Three Phase
One Phase
L1
L2
L3
6.75
16.3 16.3 28.1
32.5
/9.0
/18.8 /18.8 /32.5
/37.5
Terminal
Block
21
21
22
22
19
19
8
18
One 18
Phase
22
22
99
L3
21
21
L2
19
19
Three
Phase
45
45
21
21
19
19
N
Three
Phase
WYE 50Hz
88
33
77
44
66
Control
PC Borad
46
46
55
66
18
18
10
10
14
14
12
12
11
11
11
13
13
22
10
10
15 33
15
17
17
44
16
16
12
11 12
11
15
15
14
14
N.C. N.O. COM
High Limit
18
18
14
14
55
88
20
20
L3
44
77
22
Control
PC Borad
RTD
Temperature
Sensor
55
19
19
11
20
20
L1
77
66
19
19
L1
33
21
20
20
L2
RTD
Temperature
Sensor
22
11
L2
L1
4.5 KW Element
16
16
17
17
N.C. N.O. COM
High Limit
Pilot
Light
Control
Potentiometer
Pilot
Light
Control
Potentiometer
EG-36H VOLTS: 208/240 HZ: 50/60 PH: 1/3
NOMINAL AMPS/LINE
Three Phase
One Phase
L1
L2
L3
28.1 28.1 28.1
48.7
/32.5 /32.5 /32.5
/56.3
Total KW
10.12
/13.5
4.5 KW Element
Terminal
Block
21
21
L2
20
20
21
33
33
22
22
19
19
L1
9
18
One 18
11
20
20
33
33
L3
32
32
21
21
L2
19
19
L2
L3
N
Three
Phase
WYE 50Hz
Control
PC Board
10
10
20
20
88
33
77
66
Control
PC Board
46
46
11
12
12
13
13
22
10
10
21
21
32
33
11 12
11
18
44
15
15
14
14
Control
Potentiometer
33
26
26
Control
PC Board
24
24
25
25
31
31
23
28 23
28
16
16
30
30
17
29
29
24
24
28
28
N.C. N.O. COM
31
31
High Limit
Pilot
Light
25
25
27
27
17
17
16
16
N.C. N.O. COM
31
31
27
27
44
55
3
15 3
15
RTD
Temperature
Sensor
25
25
26
26
32
32
24
24
47
47
14
14
High Limit
19
55
14
14
66
23
23
33
33
77
22
11
11
L1
55
19
19
22
22
45
45
44
RTD
Temperature
Sensor
88
18
18
Three
Phase
99
33
77
66
19
19
32
32
Phase
L1
RTD
Temperature
22
Sensor
11
4.5 KW Element
4.5 KW Element
Pilot
Light
29
29
30
N.C. N.O. COM
High Limit
Control
Potentiometer
Pilot
Light
Control
Potentiometer
EG-48H VOLTS: 208/240 HZ: 50/60 PH: 1/3
NOMINAL AMPS/LINE
Three Phase
One Phase
L1
L2
L3
43.0 43.0 28.1
65
/49.6 /49.6 /32.5
/75
Total KW
13.5
/18.0
4.5 KW Element
Terminal
Block
11
21
21
L2
33
20
L1
32
10
18
18
One
Phase
L1
L3
33
7
19
19
11
Control
PC
Board
13
13
20
20
21
21
33
33
19
19
Three
Phase
WYE 50Hz
32
32
18
18
43
8
33
77
Control
PC
Board
46
46
88
15 33
15
11 12
11
15
15
14
14
Pilot
Light
44
High Limit
Control
Potentiometer
31
31
27
27
33
26
26
Control
PC
Board
29
29
24
24
28
28
31
31
38
38
33
37
37
Control
PC
Board
48
48
34
39 34
39
29
29
41
41
40
40
30
35
35
39
39
42
42
Pilot
Light
40
40
41
N.C. N.O. COM
High Limit
Control
Potentiometer
35
35
36
36
42
42
N.C. N.O. COM
High Limit
Control
Potentiometer
RTD Temp.
Sensor
36
36
38
38
30
30
17
42
42
24
24
25
25
23
28 23
28
Pilot
Light
35
35
36
36
37
37
43
43
47
47
N.C. N.O. COM
34
34
25
25
31
31
16
16
RTD Temp.
Sensor
44
44
27
27
17
17
16
16
32
32
24
24
4.5 KW Element
25
25
26
44
55
14
14
N.C. N.O. COM
High Limit
44
44
L3
10
10
55
66
12
12
22
33
33
14
14
22
11
23
23
77
6
10
10
RTD Temp.
Sensor
19
19
22
22
45
45
44
55
66
11
11
L1
N
44
44
18
18
Three
Phase
L2
19
43
33
43
43
19
19
L2
22
22
32
32
21
21
RTD Temp.
Sensor
21
44
99
20
20
22
4.5 KW Element
4.5 KW Element
Pilot
Light
Control
Potentiometer
APW WYOTT EQUIPMENT LIMITED WARRANTY
APW Wyott Foodservice Equipment Company warrants it's equipment against defects in materials and workmanship, subject to the
following conditions:
This warranty applies to the original owner only and is not assignable.
Should any product fail to function in its intended manner under normal use within the limits defined in this warranty, at the option of
APW Wyott such product will be repaired or replaced by APW Wyott or its Authorized Service Agency. APW Wyott will only be
responsible for charges incurred or service performed by its Authorized Service Agencies. The use of other than APW Wyott
Authorized Service Agencies will void this warranty and APW Wyott will not be responsible for such work or any charges associated
with same. The closest APW Wyott Authorized Service Agent must be used.
This warranty covers products shipped into the 48 contiguous United States, Hawaii, metropolitan areas of Alaska and Canada. There
will be no labor coverage for equipment located on any island not connected by roadway to the mainland.
Warranty coverage on products used outside the 48 contiguous United States, Hawaii, and metropolitan areas of Alaska and Canada
may vary. Contact the international APW Wyott distributor, dealer, or service agency for details.
Time Period
One year for parts and one year for labor, effective from the date of purchase by the original owner. The Authorized Service Agency
may, at their option, require proof of purchase. Parts replaced under this warranty are warranted for the un-expired portion of the
original product warranty only.
Exceptions
*Gas/Electric Cookline: Models GCB, GCRB, GF, GGM, GGT, CHP-H, EF, EG, EHP. Three (3) Year Warranty on all
component parts, except switches and thermostats. (2 additional years on parts only. No labor on second or third year.)
*Broiler Briquettes, Rock Grates, Cooking Grates, Burner Shields, Fireboxes: 90 Day Material Only. No Labor.
*Heat Strips: Models FD, FDL, FDD, FDDL. Two (2) Year Warranty on element only. No labor second year.
*Glass Windows, Doors, Seals, Rubber Seals, Light Bulbs: 90 Day Material Only. No Labor.
In all cases, parts covered by extended warranty will be shipped FOB the factory after the first year.
Portable Carry In Products
Equipment weighing over 70 pounds or permanently installed will be serviced on-site as per the terms of this warranty. Equipment
weighing 70 pounds or under, and which is not permanently installed, i.e. with cord and plug, is considered portable and is subject to
the following warranty handling limitations. If portable equipment fails to operate in its intended manner on the first day of
connection, or use, at APW Wyott's option or its Authorized Service Agency, it will be serviced on site or replaced.
From day two through the conclusion of this warranty period, portable units must be taken to or sent prepaid to the APW Wyott
Authorized Service Agency for in-warranty repairs. No mileage or travel charges are allowed on portable units after the first day of use.
If the customer wants on-site service, they may receive same by paying the travel and mileage charges. Exceptions to this rule: (1)
countertop warmers and cookers, which are covered under the Enhanced Warranty Program, and (2) toasters or rollergrills which have
in store service.
Exclusions
The following conditions are not covered by warranty:
*Equipment failure relating to improper installation, improper utility connection or supply and problems due to
ventilation.
*Equipment that has not been properly maintained, calibration of controls, adjustments, damage from improper cleaning
and water damage to controls.
*Equipment that has not been used in an appropriate manner, or has been subject to misuse or misapplication, neglect,
abuse, accident, alteration, negligence, damage during transit, delivery or installation, fire, flood, riot or act of god.
*Equipment that has the model number or serial number removed or altered.
If the equipment has been changed, altered, modified or repaired by other than an Authorized Service Agency during or after the
warranty period, then the manufacturer shall not be liable for any damages to any person or to any property, which may result from the
use of the equipment thereafter.
This warranty does not cover services performed at overtime or premium labor rates. Should service be required at times which
normally involve overtime or premium labor rates, the owner shall be charged for the difference between normal service rates and such
premium rates. APW Wyott does not assume any liability for extended delays in replacing or repairing any items beyond its control.
In all cases, the use of other than APW Wyott Authorized OEM Replacement Parts will void this warranty.
This equipment is intended for commercial use only. Warranty is void if equipment is installed in other than commercial application.
Water Quality Requirements
Water supply intended for a unit that has in excess of 3.0 grains of hardness per gallon (GPG) must be treated or softened before
being used. Water containing over 3.0 GPG will decrease the efficiency and reduce the operation life of the unit.
Note: Product failure caused by liming or sediment buildup is not covered under warranty.
“THE FOREGOING WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES EXPRESSED OR IMPLIED
INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSES
AND CONSTITUTES THE ENTIRE LIABILITY OF APW WYOTT. IN NO EVENT DOES THE LIMITED WARRANTY
EXTEND BEYOND THE TERMS STATED HEREIN.”
9/05
11
R
24 Hour Toll Free
Service Hot Line:
1-800-733-2203
APW WYOTT Foodservice Equipment Company
P.O. Box 1829
Cheyenne, WY 82003
+1 (307) 634-5801 Phone
+1 (307) 637-8071 Fax
+1 (800) 752-0863 Toll Free
www.apwwyott.com
12