Pure Acoustics AV-1080 User guide

Model SR4001/SR5001 User Guide
AV Surround Receiver
IMPORTANT SAFETY
INSTRUCTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.
READ BEFORE OPERATING EQUIPMENT
This product was designed and manufactured to
meet strict quality and safety standards. There are,
however, some installation and operation precautions
which you should be particularly aware of.
1.
Read Instructions – All the safety and
operating instructions should be read before
the product is operated.
2.
Retain Instructions – The safety and
operating instructions should be retained for
future reference.
3.
Heed Warnings – All warnings on the product
and in the operating instructions should be
adhered to.
4.
Follow Instructions – All operating and use
instructions should be followed.
5.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG
TO WIDE SLOT, FULLY INSERT.
Cleaning – Unplug this product from the
wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
6.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA
LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE
DE LA PRISE ET POUSSER JUSQU’AU FOND.
Attachments – Do not use attachments not
recommended by the product manufacturer
as they may cause hazards.
7.
Water and Moisture – Do not use this product
near water-for example, near a bath tub,
wash bowl, kitchen sink, or laundry tub, in a
wet basement, or near a swimming pool, and
the like.
8.
Accessories – Do not place this product on
an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious
injury to a child or adult, and serious damage
to the product. Use only with a cart, stand,
tripod, bracket, or table recommended by the
manufacturer, or sold with the product. Any
mounting of the product should follow the
manufacturer’s instructions, and should use
a mounting accessory recommended by the
manufacturer.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
NOTE TO CATV SYSTEM INSTALLER:
This reminder is provided to call the CATV (Cable-TV) system installer’s attention to Section 820-40 of the
NEC which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
NOTE:
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by tuning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
NOTE:
Changes or modifications not expressly approved by
the party responsible for compliance could void the
user’s authority to operate the equipment.
9.
A product and cart combination should be
moved with care. Quick stops, excessive
force, and uneven surfaces may cause the
product and cart combination to overturn.
10.
Ventilation – Slots and openings in the
cabinet are provided for ventilation and to
ensure reliable operation of the product and
to protect it from overheating, and these
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should not
be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions
have been adhered to.
11.
Power Sources – This product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your product dealer or local
power company. For products intended to
operate from battery power, or other sources,
refer to the operating instructions.
12.
Grounding or Polarization – This product
may be equipped with a polarized
alternatingcurrent line plug (a plug having
one blade wider than the other). This plug will
fit into the power outlet only one way. This is
a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of
the polarized plug.
16.
Lightning – For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods
of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This
will prevent damage to the product due to
lightning and power-line surges.
17.
Power Lines – An outside antenna system
should not be located in the vicinity of
overhead power lines or other electric light or
power circuits, or where it can fall into such
power lines or circuits. When installing an
outside antenna system, extreme care should
be taken to keep from touching such power
lines or circuits as contact with them might be
fatal.
AC POLARIZED PLUG
13.
14.
15.
Power-Cord Protection – Power-supply cords
should be routed so that they are not likely
to be walked on or pinched by items placed
upon or against them, paying particular
attention to cords at plugs, convenience
receptacles, and the point where they exit
from the product.
Protective Attachment Plug – The product
is equipped with an attachment plug having
overload protection. This is a safety feature.
See Instruction Manual for replacement or
resetting of protective device. If replacement
of the plug is required, be sure the service
technician has used a replacement plug
specified by the manufacturer that has the
same overload protection as the original plug.
Outdoor Antenna Grounding – If an outside
antenna or cable system is connected to the
product, be sure the antenna or cable system
is grounded so as to provide some protection
against voltage surges and built-up static
charges. Article 810 of the National Electrical
Code, ANSI/NFPA 70, provides information
with regard to proper grounding of the mast
and supporting structure, grounding of the
lead-in wire to an antenna-discharge unit,
size of grounding conductors, location
of antennadischarge unit, connection to
grounding electrodes, and requirements for
the grounding electrode. See Figure 1.
18.
Overloading – Do not overload wall outlets,
extension cords, or integral convenience
receptacles as this can result in a risk of fire
or electric shock.
19.
Object and Liquid Entry – Never push objects
of any kind into this product through openings
as they may touch dangerous voltage points
or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind
on the product.
20.
d.
If the product does not operate normally by
following the operating instructions. Adjust
only those controls that are covered by
the operating instructions as an improper
adjustment of other controls may result in
damage and will often require extensive
work by a qualified technician to restore the
product to its normal operation.
e.
If the product has been dropped or damaged
in any way, and
f.
When the product exhibits a distinct change
in performance this indicates a need for
service.
Damage Requiring Service – Unplug this
product from the wall outlet and refer
servicing to qualified service personnel under
the following conditions:
a.
When the power-supply cord or plug is
damaged.
b.
If liquid has been spilled, or objects have
fallen into the product.
c.
If the product has been exposed to rain or
water.
Replacement Parts – When replacement
parts are required, be sure the service
technician has used replacement parts
specified by the manufacturer or have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
23.
Safety Check – Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in proper
operating condition.
24.
Wall or Ceiling Mounting – The product
should be mounted to a wall or ceiling only
as recommended by the manufacturer.
25.
Heat – The product should be situated away
from heat sources such as radiators, heat
registers, stoves, or other products (including
amplifiers) that produce heat.
FIGURE 1
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70
Servicing – Do not attempt to service this
product yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualified service personnel.
21.
22.
ANTENNA
LEAD IN WIRE
GROUND
CLAMP
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC - NATIONAL ELECTRICAL CODE
This Class B digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la Classe B est conforme
à la norme NMB-003 du Canada.
INTRODUCTION .....................................1
PRECAUTIONS.......................................1
DESCRIPTION ........................................2
FEATURES ..............................................3
ACCESSORIES.......................................3
FRONT PANEL........................................4
SR4001.................................................................................4
SR5001.................................................................................4
FL DISPLAY..........................................................................6
REAR PANEL ..........................................7
SR4001.................................................................................7
SR5001.................................................................................7
REMOTE CONTROL OPERATION........9
FUNCTION AND OPERATION ...........................................9
OPERATION OF REMOTE CONTROL UNIT .................. 11
GENERAL INFORMATION OF RC5001SR TO
SR4001/SR5001 ................................................................12
CONTROLLING MARANTZ COMPONENTS ..................13
BASIC OPERATION ..........................................................15
CONNECTIONS ....................................17
SPEAKER PLACEMENT...................................................17
CONNECTING SPEAKERS ..............................................17
CONNECTING AUDIO COMPONENTS ..........................18
CONNECTING VIDEO COMPONENTS ..........................19
ADVANCED CONNECTING .............................................20
CONNECTING THE REMOTE CONTROL JACKS .........20
CONNECTING THE ANTENNA TERMINALS ..................21
XM RADIO OVERVIEW (SR5001 only) ............................22
CONNECTING THE XM ANTENNA .................................22
CONNECTING FOR THE
MULTI ROOM (SR5001 only) ............................................23
SETUP ...................................................25
ON SCREEN DISPLAY MENU SYSTEM .........................25
1 INPUT SETUP (ASSIGNABLE DIGITAL INPUT AND
COMPONENT VIDEO INPUT) ..........................................26
2 SPEAKER SETUP .........................................................26
3 PREFERENCE ..............................................................27
4 SURROUND ..................................................................28
5 PL II (PRO LOGIC II) MUSIC PARAMETER ...............28
6 CS II (CIRCLE SURROUND II) PARAMETER ............28
7 7.1 CH INPUT LEVEL ....................................................29
8 MULTI ROOM (SR5001 only) ........................................29
SIMPLE SETUP ....................................30
BASIC OPERATION (PLAYBACK) ......31
SELECTING AN INPUT SOURCE ....................................31
VIDEO CONVERT .............................................................31
SELECTING THE SURROUND MODE............................32
ADJUSTING THE MAIN VOLUME ...................................32
ADJUSTING THE TONE (BASS & TREBLE) CONTROL ....32
TEMPORARILY TURNING OFF THE SOUND ...................32
USING THE SLEEP TIMER ..............................................32
NIGHT MODE ...................................................................32
SURROUND MODE ..............................33
OTHER FUNCTION ..............................36
TV AUTO ON/OFF FUNCTION .........................................36
ATTENUATION TO ANALOG INPUT SIGNAL ...................36
LISTENING THROUGH HEADPHONES ........................36
DOLBY HEADPHONE MODE...........................................36
VIDEO ON/OFF ................................................................36
DISPLAY MODE ................................................................36
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT ....................................................37
RECORDING AN ANALOG SOURCE ..............................37
HT-EQ ................................................................................37
7.1 CH INPUT ....................................................................37
AUX2 INPUT ......................................................................38
LIP.SYNC (SR5001 only) ...................................................38
INTRODUCTION
PRECAUTIONS
Thank you for purchasing the Marantz SR4001/
SR5001 Surround receiver.
This remarkable component has been engineered
to provide you with many years of home theater
enjoyment. Please take a few minutes to read this
manual thoroughly before you connect and operate
the SR4001/SR5001.
As there are a number of connection and configuration
options, you are encouraged to discuss your own
particular home theater setup with your Marantz A/V
specialist dealer.
DO NOT LOCATE IN THE FOLLOWING PLACES
This user guide covers the SR4001 and
SR5001, though the SR4001 is given for the
title. Explanations of features belonging
only to the SR5001 are indicated as “SR5001
only”.
To ensure long-lasting use, do not locate the SR4001/
SR5001 where it is:
• Exposed to direct sunlight.
• Near sources of heat such as heaters.
• In highly humid or poorly ventilated environments.
• Dusty.
• Subjected to mechanical vibrations.
• On wobbly, inclined or otherwise unstable
surfaces.
• In locations such as in cramped audio racks
where radiated heat is blocked. To ensure proper
heat radiation, ensure the below clearance from
walls and other equipment.
8 ins.(0.2 m)
XM Satellite Radio Ready
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
READY
8 ins.(0.2 m)
8 ins.(0.2 m)
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/OFF
BASIC OPERATION (TUNER) .............38
LISTENING TO THE TUNER ............................................38
PRESET MEMORY ...........................................................39
LISTENING TO XM SATELLITE RADIO...........................41
SEARCH MODE ................................................................42
PRESET MEMORY ...........................................................44
TROUBLESHOOTING.......................................................45
ENGLISH
TABLE OF CONTENTS
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
8 ins.(0.2 m)
The XM name and related logos are registered
trademarks of XM Satellite Radio Inc.
MULTI ROOM SYSTEM
(SR5001 only) ..................................46
MULTI ROOM PLAYBACK USING THE
MULTI ROOM OUT TERMINALS .....................................46
MULTI ROOM PLAYBACK USING THE
MULTI SPEAKER TERMINALS ........................................46
SURROUND SPEAKER B SYSTEM
(SR4001 only) ..................................47
ANOTHER ROOM PLAYBACK USING THE
S (SURROUND) SPEAKER B TERMINALS ....................47
TROUBLESHOOTING ..........................48
TECHNICAL SPECIFICATIONS ..........49
DIMENSIONS .......................................49
SETUP CODES ........................................I
1
ENGLISH
DESCRIPTION
DTS was introduced in 1994 to provide 5.1 channels of
discrete digital audio into home theater systems.
DTS brings you premium quality discrete multichannel
digital sound to both movies and music.
DTS is a multichannel sound system designed to
create full range digital sound reproduction.
The no compromise DTS digital process sets the
standard of quality for cinema sound by delivering
an exact copy of the studio master recordings to
neighborhood and home theaters.
Now, every moviegoer can hear the sound exactly as
the moviemaker intended.
DTS can be enjoyed in the home for either movies or
music on of DVD’s, LD’s, and CD’s.
DTS-ES Extended Surround is a new multichannel
digital signal format developed by Digital Theater
Systems Inc. While offering high compatibility with
the conventional DTS Digital Surround format, DTSES Extended Surround greatly improves the 360degree surround impression and space expression
thanks to further expanded surround signals. This
format has been used professionally in movie
theaters since 1999.
In addition to the 5.1 surround channels (FL, FR, C,
SL, SR and LFE), DTS-ES Extended Surround also
offers the SB (Surround Back) channel for surround
playback with a total of 6.1 channels. DTS-ES
Extended Surround includes two signal formats with
different surround signal recording methods, as DTSES Discrete 6.1 and DTS-ES Matrix 6.1.
“DTS” and “DTS Digital Surround” are registered
trademarks of Digital Theater Systems, Inc.
“DTS”, “DTS-ES” and “Neo:6” are trademarks of
Digital Theater Systems, Inc.
The advantages of discrete multichannel systems
over matrix are well known.
But even in homes equipped for discrete multichannel,
there remains a need for high-quality matrix decoding.
This is because of the large library of matrix surround
motion pictures available on disc and on VHS tape; and
analog television broadcasts.
The typical matrix decoder of today derives a center
channel and a mono surround channel from twochannel matrix stereo material. It is better than a
simple matrix in that it includes steering logic to
improve separation, but because of its mono, bandlimited surround it can be disappointing to users
accustomed to discrete multichannel.
The stereo CD is a 16-bit medium with sampling at
44.1 kHz. Professional audio has been 20- or 24bit for some time, and there is increasing interest
in higher sampling rates both for recording and for
delivery into the home. Greater bit depths provide
extended dynamic range. Higher sampling rates
allow wider frequency response and the use of antialias and reconstruction filters with more favorable
aural characteristics.
Neo:6 offers several important improvements as
follow,
• Neo:6 provides up to six full-band channels of
matrix decoding from stereo matrix material. Users
with 6.1 and 5.1 systems will derive six and five
separate channels, respectively, corresponding to
the standard home-theater speaker layouts.
• Neo:6 technology allows various sound elements
within a channel or channels to be steered
separately, and in a way which follows naturally
from the original presentation.
• Neo:6 offers a music mode to expand stereo nonmatrix
recordings into the five- or six-channel layout, in a way
which does not diminish the subtlety and integrity of
the original stereo recording.
2
DTS 96/24 allows for 5.1channel sound tracks to be
encoded at a rate of 96kHz/24bits on DVD-Video
titles.
When DVD-video appeared, it became possible to
deliver 24-bit, 96 kHz audio into the home, but only in
two channels, and with serious limitations on picture.
This capability has had little use.
DVD-audio allows 96/24 in six channels, but a
new player is needed, and only analog outputs are
provided, necessitating the use of the D/A converters
and analog electronics provided in the player.
DTS 96/24 offers the following:
1. Sound quality transparent to the original 96/24
master.
2. Full backward compatibility with all existing
decoders. (Existing decoders will output a 48 kHz
signal)
3. No new player required: DTS 96/24 can be carried
on DVD-video, or in the video zone of DVD-audio,
accessible to all DVD players.
4. 96/24 5.1-channel sound with full-quality fullmotion video, for music programs and motion
picture soundtracks on DVD-video.
“DTS” and “DTS 96/24” are trademarks of Digital
Theater Systems, Inc.
Dolby Digital identifies the use of Dolby Digital audio
coding for such consumer formats as DVD and DTV.
As with film sound, Dolby Digital can provide up
to five full-range channels for left, center, and right
screen channels, independent left and right surround
channels, and a sixth (“.1”) channel for low-frequency
effects.
Dolby Surround Pro Logic II is an improved matrix
decoding technology that provides better spatiality
and directionality on Dolby Surround program
material; provides a convincing three-dimensional
soundfield on conventional stereo music recordings;
and is ideally suited to bring the surround experience
to automotive sound. While conventional surround
programming is fully compatible with Dolby Surround
Pro Logic II decoders, soundtracks will be able to be
encoded specifically to take full advantage of Pro
Logic II playback, including separate left and right
surround channels. (Such material is also compatible
with conventional Pro Logic decoders.)
Dolby Digital EX creates six full-bandwidth output
channels from 5.1-channel sources. This is done
using a matrix decoder that derives three surround
channels from the two in the original recording. For
best results, Dolby Digital EX should be used with
movies soundtracks recorded with Dolby Digital
Surround EX.
About Dolby Pro Logic IIx
Dolby Pro Logic IIx technology delivers a natural
and immersing 7.1-channel listening experience
to the home theater environment. A product of
Dolby’s expertise in surround sound and matrix
decoding technologies, Dolby Pro Logic IIx is a
complete surround sound solution that maximizes
the entertainment experience from stereo as well as
5.1-channel encoded sources.
Dolby Pro Logic IIx is fully compatible with Dolby
Surround Pro Logic technology and can optimally
decode the thousands of commercially available
Dolby Surround encoded video cassettes and
television programs with enhanced depth and
spatiality. It can also process any high-quality
stereo or Advanced Resolution 5.1-channel music
content into a seamless 6.1- or 7.1-channel listening
experience.
The Dolby Headphone technology provides a
surround sound listening experience over headphones.
When listening to multichannel content such as DVD
movies over headphones, the listening experience
is fundamentally different than listening to speakers.
Since the headphone speaker drivers are covering
the pinna of the ear, the listening experience differs
greatly from traditional speaker playback. Dolby
utilizes patented headphone perspective curves to
solve this problem and provides a non-fatiguing,
immersive, home theater listening experience. Dolby
Headphone also delivers exceptional 3D audio from
stereo material.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic”, “Surround EX”, and the doubleD symbol are trademarks of Dolby Laboratories.
Circle Surround II (CS-II) is a powerful and versatile
multichannel technology. CS-II is designed to enable
up to 6.1 multichannel surround sound playback
from mono, stereo, CS encoded sources and other
matrix encoded sources. In all cases the decoder
extends it into 6 channels of surround audio and a
LFE/subwoofer signal. The CS-II decoder creates a
listening environment that places the listener “inside”
music performances and dramatically improves
both hi-fi audio conventional surround-encoded
video material. CS-II provides composite stereo rear
channels to greatly improve separation and image
positioning – adding a heightened sense of realism
to both audio and A/V productions.
P
AIT
STER
CT
TUAL
6
EO
GHT
IN
4
P.S
CA
SURR
BAN
D
4
NI
H
1C
7.
A/D
ENGLISH
ON
IRE
3
VIR
s
dt
ST
5
9
+10
A/B
OFF
Y
P.D
S
/E
EX
0
AT
E
UT
M
AT
I/C
ULT
M
LIP
INP SYNC
UT
OU
ND
/
T.M
OD
E
N
HT-EQ
ME
MO
E
UM
LL
VO
M-S
PKR
TE
PLA
2
II
H
-C
M
L
/C
CH
D
EN
ME
R
SS
CS
SEND
SET
P
EE
SL
8
SPKR
OS
T.T
SETUONE
P/
BA
NU
T.D
ISP
PRES
ET
PTY
+
IT
SC
EX
DI
F.D
L
V-O
SUBT
FF
IRE
TUNIN
GLE
AN
CH-SE
CT
G
BA
ITL
SS DV
E
ATT.
AU
DIO
D
V
CD
C
R
TREB
LE
D
R
CD
S
S
SY
MD
2
M
X
AU
STE
P
AM
NTR
CO
TE R
O S
M 00
RE C55
R
O
LL
ER
• Dolby Digital EX, Dolby Digital ,
DTS ES (Discrete 6.1, Matrix 6.1, Neo: 6)
• Dolby Headphone 2
• Dolby Pro Logic IIx (Movie, Music, Game)
• Circle Surround II (Movie, Music, Mono)
• HDCD decording
• 7 × 80 Watts (8 Ohm) (SR4001)/7 × 90 Watts (8
Ohm) (SR5001), Discrete Amplifiers
• High Power Current Feedback Circuitry
• Massive Energy Power Supply, Huge EI
Transformer, Large ELCO’s.
• 192 kHz/24 bit Crystal® DAC for all 8 Channels
• 32 bit Digital Surround Processing Chipsets
• Video Off Mode
• Large Heavy Duty Speaker Terminals for all
Channels
• RS-232C Terminal for System Control (SR5001only)
• Set Up Menu via all Video Output (Composite, SVideo and Component video)
• Auto Input Signal Detection
• Improved Station Name Input Method, 50 Presets
• Auto Adjust Function for Speaker Distance Settings
(Delay Time)
• Front AUX Input (Digital Camera, Portable DVD)
• Universal remote control
• Simple Setup Function
• Video convert system
• LIP.SYNC Funciton (Audio delay) (SR5001 only)
N
URCE
DIS
1
The SR4001/SR5001 is designed and engineered
with extensive feedback from custom installation
experts, dealers and consumers. It features multiroom/multisource, a RS-232C communication port
(SR5001 only), heavy duty speaker binding posts
and an extensive array of both analog and digital
inputs / outputs. With 6 assignable digital inputs
(including Front Aux), 3 assingnable component
inputs (SR5001), 5 assignable digital input
(SR4001), Super Audio CD Multi Channel (7.1
channel) direct inputs video convert system and
OSD output versatility is taken to a stunning new
level. Furthermore, the SR4001/SR5001 can output
the OSD information through the Y/C (S-video) and
composite video outputs.
LEAR
SO
l/
1
4
7
X
AU
HDMI, the
and High-Definition Multimedia
Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
The SR4001/SR5001 incorporates the most
advanced Digital Signal Processing circuitry, along
with a Crystal® 192 kHz/24 bit D/A converter in
each of the 7 channels. Independent power supply
circuits are incorporated for the FL display, audio
and video sections for maximum separation, clarity
and dynamic range. Together with hand-selected
customized components, all elements work in
harmony to recreate the emotion, exactly as the artist
had intended.
Remote Controller RC5001SR
This unit has Simple Setup function for easy setup.
You can setup all speaker settings by just selecting
your room size and the number of your speakers with
Simple Setup function. You can also setup customized
settings just like conventional AV amplifiers.
PE
TA
HDCD system manufactured under license from
Microsoft. This product is covered by one or more
of the following: In the United States 5,479,168
5,638,074 5,640,161 5,808,574 5,838,274 5,854,600
5,864,311 5,872,531 and in Australia 669,114 with
other patents pending.
The SR4001/SR5001 features a fully discrete 7
channel amplifier section capable of delivering 80
watts (SR4001)/90 watts (SR5001) of high-current
amplification, for continuously clean and stable
power into each of the 7 channels. It employs a
massive EI power transformer in combination with
oversized filter capacitors. This design configuration
is capable of a clear and powerful reproduction of the
most demanding action movie soundtracks and full
range (multichannel) music discs. Through its ability
to generate very high output voltages, the SR4001/
SR5001 can easily drive the most demanding
speakers with optimum results.
ACCESSORIES
R
NE
TU
HDCD® (High Definition Compatible Digital ®) is a
patented process for delivering on Compact Disc the
full richness and details of the original microphone
feed.
HDCD encoded CDs sound better because they are
encoded with 20-bits of real musical information as
compared to 16-bits for all other CDs.
HDCD overcomes the limitation of the 16-bit CD
format by using a sophisticated system to encode
the additional four bits onto the CD while remaining
completely compatible with the CD format.
When listening to HDCD recordings, you hear more
dynamic range, a focused 3-D sound stage, and
extremely natural vocal and musical timbre. With
HDCD, you get the body, depth and emotion of the
original performance not a flat, digital imitation.
The SR4001/SR5001 incorporates the latest
generation of digital surround sound decoding
technology such as Dolby Digital EX, Dolby Digital,
DTS-ES (Discrete 6.1 and Matrix 6.1), DTS Neo:6
(Cinema, Music), Dolby Pro-Logic IIx (Movie, Music
and Game), Circle Surround II (Cinema and Music).
In addition, Marantz has focused on the future.
By utilizing pre-out jacks, 7.1 direct inputs and a
RS-232C communication port (SR5001 only), the
SR4001/SR5001 is tomorrow’s technology, today!
An easy-to-use universal remote control allows full
access to all of the operating functions and can be
used for system operation as well.
TV
Circle Surround II, Dialog Clarity, TruBass, SRS and
symbol are trademarks of SRS Labs, Inc.
Circle Surround II, Dialog Clarity and TruBass
technology are incorporated under license from SRS
Labs, Inc.
FEATURES
C
CS-II is packed with other useful feature like dialog
clarity (SRS Dialog) for movies and cinema-like bass
enrichment (TruBass). CS-II can enable the dialog
to become clearer and more discernable in movies
and it enables the bass frequencies contained in
the original programming to more closely achieve
low frequencies – overcoming the low frequency
limitations of the speakers by full octave.
AAA-size batteries × 2
AM Loop Antenna
FM Antenna
AC Power Cord
Front AUX Jack Cover
P
PU
US
SH
H
User Guide
Warranty Card
USA × 1
Canada × 1
3
ENGLISH
q
FRONT PANEL
When this switch is pressed once, the unit turns ON
and the display illuminates. When pressed again, the
unit turns OFF and the STANDBY indicator will be
illuminated.
SR4001
qw e
r ty u i
o !0
!1
!2
!3
w
VOLUME
DOWN
SURROUND
MODE
7.1 CH INPUT
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
MUTE
STANDBY
w
UP
ATT
ENTER
AUTO
POWER ON/STANDBY
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
@2
@1 @0 !9 !8 !7 !6 !5 !4
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
e
R
qw e
r ty u i
o !0
@3
!1
!2
!3
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
READY
DOWN
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
L
AUDIO
R
@1 @0 !9 !8 !7 !6 !5 !4
@3
PURE DIRECT button and
indicator
When this button is pressed once, “SOURCE DIRECT”
appears on the FL display. If pressed again, “PURE
DIRECT” appears. After 2 seconds, the FL display
indication goes out.
In the source/pure direct mode, the tone control
circuitry and bass management are bypassed.
Notes:
• The surround mode is automatically switched to
AUTO when the pure direct function is turned on.
• Additionally, speaker configurations are fixed
automatically as follows.
Front SPKR = LARGE
Center SPKR = LARGE
Surround SPKR = LARGE
Surround Back SPKR = LARGE
Sub woofer = YES
i
SIMPLE SETUP button
Press this button to enter the simple setup mode.
You can setup the speaker conditions (speaker
sizes, number of speakers, speaker delay times)
quickly by pressing the cursor buttons.
DISPLAY button
r
!0
S.(Surround) SPEAKER B button
(SR4001 only)
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
u
Press this button to activate the Multiroom Speaker
system. “MULTI” indicator will be illuminated in the
display. (See page 46)
Press this button to activate the Surround Speaker B
system . “SPKR B” indicator will be illuminated in the
display. (See page 47)
t
@2
M.(Multi Room) SPEAKER button
(SR5001 only)
SURROUND MODE button
You can select the surround mode by pressing this
button.
When this button is pressed, the FL display mode
is changed as Surround Mode → Auto-display Off
→ Display Off → Input Function and the display off
indicator(DISP) lights up in condition of DISPLAY
OFF.
CLEAR
MUTE
y
o
r
UP
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
MULTI SPEAKER
STANDBY
INPUT SELECTOR knob
(AUDIO/ VIDEO)
This knob is used to select the input sources.
The video SOURCE, such as TV, DVD, VCR1 and
DSS, selects video and audio simultaneously.
Audio function sources such as CD, TAPE, CDR/MD,
and TUNER may be selected in conjunction with a
Video source.
This feature (Sound Injection) combines a sound
from one source with a picture from another.
Choose the video source first, and then choose a
different audio source to activate this function.
SR5001
MULTI
7.1CH INPUT button (SR4001 only)
Press this button to select the output of an external
multichannel player.
CLEAR
S.SPEAKER B
MULTI (Multi Room) button
(SR5001 only)
Press this button to activate the Multiroom system.
“MULTI” indicator will be illuminated in the display.
AV SURROUND RECEIVER SR4001
INPUT SELECTOR
4
POWER switch and STANDBY
indicator
INFRARED receiving sensor
window
This window receives infrared signals for the remote
control.
MEMORY button
Press this button to enter the tuner preset memory
numbers or station names. (See page 39)
!1
CLEAR button
Press this button to cancel the station-memory
setting mode or preset scan tuning. (See page 39)
!2
VOLUME control knob
Adjusts the overall sound level. Turning the control
clockwise increases the sound level.
ATT (Attenuate) button
If the selected analog audio input signal is greater
than the capable level of internal processing, the
PEAK indicator will illuminate. If this happens, you
should press the ATT button. “ATT” is displayed
when this function is activated.
The signal-input level is reduced by about half.
Attenuation will not work with the output signal of
“REC OUT” (TAPE, CD-R/MD, VCR1 and VCR2
output). This function is memorized for each input
function.
!4
MUTE button
Press this button to mute the output to the speakers.
Press it again to return to the previous volume level.
!5
T-MODE button
Press this button to select the auto stereo mode or
mono mode when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
(See page 39)
!6
BAND button
Press this button to switch between FM and AM in
the TUNER mode.
!7
@1
AUTO (Auto surround) button
ENGLISH
!3
Press this button to select the AUTO mode from the
surround modes. When this mode is selected, the
receiver determines the surround mode corresponding
to a digital input signal automatically.
@2
HEADPHONE jack for stereo
headphones
This jack may be used to listen to the SR4001/
SR5001’s output through a pair of headphones. Be
certain that the headphones have a standard 1 / 4”
stereo phono plug. Note that the main room speakers
will automatically be turned off when the headphone
jack is in use.
Notes:
• When using headphones, the surround mode will
change to STEREO and Dolby Headphone by
MENU and Cursor button.
• The surround mode returns to the previous setting
as soon as the headphone plug is removed from the
jack.
@3
AUX1 INPUT jacks
These auxiliary video/audio input jacks accept the
connections of a camcorder, portable DVD, game
etc.
EXIT button
This button is used to exit from the SETUP MAIN
MENU.
!8
Cursor (1, 2, 3, 4) / ENTER button
Use these buttons when operating the SETUP MAIN
MENU and TUNER function.
!9
MENU button
This button is used to enter the SETUP MAIN
MANU.
@0
HT-EQ button
Used to turn on or off HT(Home Theater)-EQ mode.
This mode compensates for the audio portion of
a movie sounding “bright”. When this button is
pressed, “EQ” indicator lights up.
5
¡4
ENGLISH
FL DISPLAY
s
a
DISP
¡8
SLEEP
f
g
d
MULTI
h
AUTO
AUTO SURR
TUNED
DIRECT
j
ST
V – OFF
DISC 6.1
k ¡0 ¡2
¡4
l ¡1 ¡3
NIGHT
MT X 6.1
PEAK
SPKR B
ANALOG input indicator
HOW TO ATTACH THE FRONT AUX JACK COVER
This indicator is illuminated when an analog input
source has been selected.
BA
ND
T-
M
OD
E
M
UTE
DIG
¡5
ANALOG
SURROUND
EQ
DIGITAL
DIGITAL
L
C
R
S
SR
AU
VID X 1
EO INP
U
a
DISP (Display Off) indicator
¡9
j
¡6
™0
V (video)-OFF mode indicator
This indicator is illuminated when the SR4001/
SR5001 is in the display off condition.
This indicator is illuminated when the Video-OFF
function is active.
s
k
SLEEP timer indicator
This indicator is illuminated when the sleep timer
function in the main-room is in use.
d
Multi-room system indicator
This indicator is illuminated when the multi-room
system is active.
f
AUTO SURR (Auto Surround
mode) indicator
This indicator is illuminated to show that the AUTO
SURROUND mode is in use.
g
TUNER’s indicators
AUTO : This indicator illuminates when the
tuner’s Auto mode is in use.
TUNED : This indicator illuminates when
a station is being received with
sufficient signal strength to provide
acceptable listening quality.
ST(Stereo) : This indicator illuminates when an
FM station is being tuned into stereo
condition.
h
DTS-ES mode indicators
(DISC6.1, MTX6.1)
These indicators will illuminate to show the DTS-ES
decoding mode (Discrete 6.1 or Matrix 6.1).
6
NIGHT mode indicator
This indicator is illuminated when the SR4001/
SR5001 is in the Night mode, which reduces the
dynamic range of digital program material at low
volume levels.
l
SPKR (speaker) B indicator
¡6
ENCODED CHANNEL STATUS
indicators
These indicators display the channels that are
encoded with a digital
input signal. If the selected digital input signal is
Dolby Digital 5.1ch or DTS 5.1ch, “L”, “C”, “R”, “SL”,
“SR” and “LFE” will be illuminated.If the digital input
signal is 2 channel PCM-audio, “L” and “R” will be
displayed.
If Dolby Digital 5.1ch signal with Surround EX flag or
DTS-ES signal comes in, “L”, “C”, “R”, “SL”, “S” , “SR”
and “LFE” will be illuminated.
¡7
Main Information Display
This display shows messages relating to the status,
input source, surround mode, tuner, volume level or
other aspects of unit’s operation.
This indicator is illuminated when the M (Multiroom)
speaker B system is active.
¡8
¡0
This indicator is illuminated when the SR4001/
SR5001 is in the SOURCE DIRECT mode.
PEAK indicator
This indicator is a monitor for an analog audio input
signal. If the selected analog audio input signal is
greater than the capable level of internal processing,
this will illuminate. If this happens, you should press
the ATT button on the remote.
¡1
EQ mode indicator
This indicator is illuminated when the HT-EQ function
is active.
¡2
ATT (Attenuation) indicator
This indicator is illuminated when the attenuation
function is active.
¡3
DIGITAL Input Indicator
This indicator lights when a digital input has been
selected.
¡9
DIRECT (Puredirect) indicator
HDCD indicator
When HDCD signal is decoded from digital input, this
indicator will light up.
™0
HDMI indicator
This indicator is illuminated when HDMI device is
connected to the SR4001/SR5001.
H
IN
PU
T
T
L
AU
DIO
R
P
PU
US
SH
H
Front AUX Jack Cover
¡7
7.
S-V
ID
EO
SIGNAL FORMAT indicators
2 DIGITAL, EX, 2 SURROUND, dts, ES, 96/24,
PCM
When the selected input is a digital source, some
of these indicators will be illuminated to display the
specific type of signal in use.
LFE
SL
UP
AL
1C
¡5
ATT
PCM
IT
These are the video inputs and outputs. There
are 4 video inputs and 2 video outputs and each
one includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
The input signals of video and S-video are converted
each other, and each of the converted video signals
can be output.
SR4001
w
!1
q
t
r
!3 !8
INPUT
1
VIDEO
!6
INPUT
3
HDMI Ver 1.1
COMPONENT
VIDEO
MONITOR
OUT
S-VIDEO
FM (75
75Ω
Ω)
GND
AM
ANTENNA
TV
L
SL
C
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
CB/PB
3
Y
SBL
INPUT 1
CR/PR
4
INPUT 2
OUTPUT
IN
COAX
VIDEO IN/OUT (TV, DVD, VCR1, DSS/
VCR2)
L
w
R
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
SBR
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
OPT
DIGITAL OUT
FLASHER
IN
OUT
RC-5
AUDIO
L
SL
C
SBL
AC IN
R
L
R
L
R
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
UNSWITCHED
1.25A 150W
L
MODEL NO. SR4001
FRONT
R
SR
SW
SURROUND BACK
S. SPEAKER B
SBR
PRE OUT
SURROUND
AC OUTLETS
120V 60Hz
SPEAKER SYSTEMS : MINIMUM 6 OHMS
y !0
!4
AM antenna and ground terminals
SWITCHED
1.25A 150W
CENTER
o
!5
i
Connect the supplied AM loop antenna. Use the
terminals marked “AM” and “GND”. The supplied AM
loop antenna will provide good AM reception in most
areas. Position the loop antenna until you hear the
best reception.
u
e
SR5001
!1
w
!2
q
t
INPUT
3
GND
C
@0
HDMI Ver 1.1
MONITOR
OUT 2
AM
TV
SL
!6
COMPONENT
VIDEO
S-VIDEO
ANTENNA
L
!8
INPUT
1
VIDEO
FM (75
75Ω
Ω)
r
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
Y
4
CB/PB
COAX
INPUT 1
CR/PR
IN
INPUT 2
OUTPUT
XM
L
R
R
(AUX2
AUX2))
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
FLASHER
DC
IN
TRIGGER
AUDIO
RS-232C
L
SL
SPEAKER C
OFF ON
C
UNSWITCHED
1.25A 150W
SBL
AC IN
R
L
R
L
R
L
R
L
MODEL NO. SR5001
FRONT B
R
SR
SW
SBR
FRONT A
SURROUND BACK
PRE OUT
e
SURROUND
FRONT A OR B,CENTER,
SPEAKER C/MULTI SPEAKER
FRONT A AND B:MINIMUM 8 OHMS SURR,SURR BACK:MINIMUM 6 OHMS
y !0 !9
o
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
!4 !5 i !3
u !7
RS-232C (SR5001 only)
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
SR5001 by using an external device.
r
COMPONENT VIDEO INPUT/
OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to
these component video connectors on the SR4001/
SR5001. The SR4001/SR5001 has two component
video input connectors to obtain the color information
(Y, CB, CR) directly from the recorded DVD signal or
other video component and one component video
output connector to output it directly into the matrix
decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra processing
that normally would degrade the image. The result is
vastly increased image quality, with incredibly life like
colors and crisp detail.
When the video convert function is enabled, video and
S-video images can be output to the COMPONENT
MOINTOR OUT jack.
t
MONITOR OUT
ENGLISH
q
REAR PANEL
This is a monitor output and each one includes both
composite video and S-video configurations. When
connecting two video monitors or televisions, be
aware that the OSD interface can be used with both
MONITOR OUT connections.
y
Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifiers.
u
AC INLET
Plug the supplied power cord into this AC INLET and
then into the power outlet on the wall.
SR4001/SR5001 can be powered by 120V AC only.
i
AC OUTLETS
Connect the AC power cable of component such as
a DVD or CD player to this outlet.
The marked SWITCHED provides power only when
the SR4001/SR5001 is turned on and is useful for
components which you use every time you play your
system.
Caution:
• In order to avoid potential turn-off thumps, anything
plugged into these outlets should be powered up
before the SR4001/SR5001 is turned on.
• The capacity of this AC outlet is 150W. Do not
connect devices that consume electricity more than
the capacity of these AC outlet. If the total power
consumption of the connected devices exceeds the
capacity, the protection circuit shuts down the power
supply.
o
Speaker outputs terminals
Seven terminals are provided for the front left,
front right, front center, surround left, surround
right, surround back left and surround back right
speakers.
Note:
You can use surround back speaker terminals as M
(Multiroom) SPEAKER B terminals, when you use
no surround back speaker.
7
ENGLISH
!0
Subwoofer Output
Connect this jack to the line level input of a powered
subwoofer. If an external subwoofer amplifier is used,
connect this jack to the subwoofer amplifier input. If
you are using two subwoofers, either powered or
with a 2 channel subwoofer amplifier, connect a “Y”
connector to the subwoofer output jack and run one
cable from it to each subwoofer amplifier.
!1
7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, Super Audio CD
multichannel player, or other components that has a
multichannel port, you can playback the audio with
5.1 channel or 7.1 channel outputs.
!2
Multiroom Outputs (SR5001 only)
These are the audio output jacks for the Multi zone
(Multi room).
Connect these jacks to optional audio power
amplifiers to listen the source selected by the
multiroom system in a remote room.
!3
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
!4
AUDIO IN/OUT (CD, TAPE, CD-R,
TV, DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs. There
are 7 audio inputs (4 of which are linked to video
inputs) and 4 audio outputs (2 of which are linked to
video outputs). The audio jacks are nominally labeled
for cassette tape decks, compact disc players, DVD
players and etc.... The audio inputs and outputs
require RCA-type connectors.
!5
DIGITAL INPUT
(SR4001 : Dig.1 - 4, SR5001 : Dig.1-5)
/ OUTPUT (coaxial, optical)
These are the digital audio inputs and outputs. There
are 2 digital inputs with coaxial jacks, 2 with optical
jacks.
The inputs accept digital audio signals from a CD,
DVD, or other digital source component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD recorders,
CD recorders, or other similar components.
!6
HDMI INPUT/OUTPUT
This unit has 2 HDMI inputs and 1 HDMI output. The
input function can be selected from the OSD menu
system. (See page 26)
!7
DC TRIGGER output terminal
(SR5001 only)
Connect a device that needs to be triggered by DC
under certain conditions (screen, power strip, etc…)
Use the system OSD setup menu to determine the
conditions by which these jack will be active.
Note:
This output voltage is for (status) control only, It is not
sufficient for drive capability.
!8
FLASHER IN
(Flasher input terminal)
These terminals are to control the unit from each
zone. Connect the control signal from a Keypad,
etc.
!9
SPEAKER C SELECTOR SWITCH
(SR5001 only)
The terminals can be used to connect a third set of
speakers by setting the SPEAKER C selector switch
to ON. For connection and use, see page 23.
@0
XM antenna terminal (SR5001 only)
Plug the XM Connect-and-play antenna or Passport
system into XM terminal.
8
z
Indicates when the remote controller is in the LEARN
mode.
x
FUNCTION AND OPERATION
The provided remote control unit is a universal
remote controller. The POWER button, numeric
buttons and control buttons are used in common
across different input source components.
The input source controlled with the remote control
unit changes when one of the input selector buttons
is pressed.
‹5
LEARN indicator
SET button
This button is used to enter learn mode and preset
mode.
c
/ SOURCE ON/OFF button
This button is used to turn a specific source (such as
a DVD player) on or off independently from the rest
of the system.
0/7.1CH IN button
Press this button to select the output of an external
multi channel decoder.
v
(+10) A/D button
Used to switch between the analog and digital
inputs.
SLEEP button
This button is used for setting the sleep timer.
z
x
c
v
b
n
m
,
.
⁄0
⁄1
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
VOLUME
INFO
MENU
T.TONE
/SET UP
EXIT
REC
⁄3
⁄4
⁄5
⁄6
-
T.DISP
PRESET
+
¤3
¤4
¤5
¤6
¤7
¤8
¤9
ENTER
⁄2
⁄7
⁄8
⁄9
¤0
¤1
¤2
PTY
-
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
‹0
F.DIRECT
AUDIO
TREBLE
‹1
‹2
‹3
‹4
9/NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This function
reduces the voice by 1/3 to 1/4 at maximum. Thus, it
eliminates the occurrence of an abruptly loud voice
at night. However, the function is valid only in the
case when the Dolby Digital signal is entered into
OPTICAL or COAXIAL and data to compress the
voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
b
DISPLAY button
Selects the display mode for the front display of the
SR4001/SR5001.
n
Numeric buttons
These buttons are used to switch between 0 to +10
of the source components.
If the source is set to the amplifier, these buttons are
used to perform operations.
(When AMP mode is selected)
m
CL (Clear) button
T.DISP button
Used to select the display mode in RDS.
PTY button
Used to display the programme type information of
the current station.
F.DIRECT button
Used to select the "Frequency direct input".
PRESET +/- buttons
Used to select a preset station up and down.
TUNING +/- buttons
Used to tune a frequency station up and down.
⁄4
ANGLE/V-OFF buton
,
⁄5
SPKR A/B button (SR5001 only)
Used to select the speaker system.
The speaker system is switched in the following
sequence.
A → B → A+B → off
.
CH/CAT3 (UP) / 4 (DOWN) buttons
2/Dolby button
Used to select DOLBY mode.
⁄0
3/dts button
Used to select dts mode.
(When AMP mode is selected)
Used to turn on and off multi room.
6/VIRTUAL button
Used to select VIRTUAL mode.
(When TUNER mode is selected)
(When AMP mode is selected)
Used to turn off the video signal.
These buttons are used to change channels.
5/EX/ES button
Used to select EX/ES mode.
CONTROL buttons
These buttons are used when operating PLAY,
STOP, PAUSE and other commands of a source.
This button is used to erase the memory or program
of a source.
1/AUTO button
Used to select auto surround.
4/CSII button
Used to select CSII mode.
⁄3
⁄1
ENGLISH
REMOTE CONTROL
OPERATION
DISC+/CH. SEL button
(When AMP mode is selected)
Used to call up SETUP MAIN MENU and adjust
speaker levels or 7.1 ch input level.
⁄6
BASS +/- buttons
These buttons are used to adjust the tone control
of low frequency sound for left, right and subwoofer
speaker.
MULTI/CAT button (SR5001 only)
INFO button
(When AMP mode is selected)
When this button is pressed, the current setting are
displayed on the TV monitor.
7/M-CH ST button
Used to select Multi Channel Stereo.
⁄2
8/STEREO button
Used to select STEREO mode.
(When AMP mode is selected)
Used to enter the test tone menu.
T.TONE/SET UP button
⁄7
SEND indicator
Indicates when the remote controller is transmitting
a signal.
⁄8
/ POWER ON and OFF buttons
(When AMP mode is selected)
These buttons are used to turn the SR4001/SR5001
on or off.
⁄9
SURROUND button
This button is used to selects the surround mode.
REMOTE CONTROLLER
RC5001SR
¤0
P.DIRECT button
When this button is pressed, the tone control circuit
is bypassed.
9
ENGLISH
¤1
BAND/LIP SYNC/INPUT button
¤6
‹2
AUDIO buttons
(When TUNER mode is selected)
Used to select a radio band.
(When DVD mode is selected)
Used to select one of the audio language.
(When AMP mode is selected)
Used to select LIP SYNC mode.
Note:
Set the AMP mode to use this button with the SR4001/
SR5001.
‹3
(When TV mode is selected)
Used to select monitor input.
¤7
¤2
T.MODE button
(When TUNER mode is selected)
Used to select auto stereo mode or mono mode
when the FM band is selected.
The “AUTO” indicator lights in the auto stereo mode.
¤3
P.SCAN button
M-SPKR button (SR5001 only)
(When AMP mode is selected)
Used to turn on and off multi speaker.
¤8
MENU button
(When AMP mode is selected)
This button is used to call up the SETUP MAIN
MENU of the SR4001/SR5001.
TREBLE +/- buttons
These buttons are used to adjust the tone control of
high frequency sound for left and right speaker.
‹4
SOURCE button
These buttons are used to switch the source of your
A/V Receiver / amplifer. Each time a source button is
pressed, the remote control changes to the source
which was pressed.
This remote control can control 12 types of equipment.
To change the A/V Receiver / amplifier source, press
this button twice within two seconds. The signal is
sent when it is pressed the second time.
(When TUNER mode is selected)
Used to start preset scan.
¤9
¤4
These buttons are used when controlling the cursor of
the SR4001/SR5001, DVD or other AV equipment.
Note:
Select the AMP as the source to use this remote
controll with the SR4001/SR5001.
‹0
‹5
MEMO/HT-EQ button
This button is used to store setting to memory or
program a source.
(When AMP mode is selected)
Used to turn on or off HT(Home Theater)-EQ mode
when the surround mode is set as AUTO, DOLBY,
DTS or STEREO.
This mode compensates for the audio portion of a
movie sounding “bright”.
When this button is pressed, “EQ” indicator light up.
¤5
MUTE button
This button is used to mute the audio for the amplifier
and television.
Note:
Set the AMP mode to use this button with the SR4001/
SR5001.
10
VOLUME +/- buttons
This button is used to adjust the volume for the
amplifier and television.
1, 2, 3, 4 (CURSOR) / ENTER buttons
EXIT button
(When AMP mode is selected)
This button is used to cancel setting in the setup
menu.
‹1
SUBTITLE/ATT. button
(When AMP mode is selected)
When the input signal is too high and the voice
distorts even by throttling the SR4001/SR5001
VOLUME control, turn on this function.
“ATT” is indicated when this function is activated.
The input level reduced. Attenuator is invalid for the
output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is
selected.
Infrared Transmitter and Learning
Sensor
This transmitter emits infrared light. Press the buttons
while pointing the transmitter towards the infrared
receiver window of the SR4001/SR5001 or other
AV equipment. Be sure to also point towards other
remote controls when using the learning function.
REMOTE CONTROL
The distance between the transmitter of the remote
control and the IR SENSOR of the SR4001/SR5001
should be less than 5 meters. If the remote control is
pointed in a direction other than the IR SENSOR or if
there is an obstacle between them, use of the remote
control may not be possible.
LOADING BATTERIES
CAUTIONS ON BATTERIES
The life of the batteries used with the remote control
is about 4 months with normal use. Also be sure to
replace batteries earlier when you notice that they
are getting weak.
• Use “AAA” type batteries in this remote control
unit.
• We recommend that you use alkali batteries.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as
possible.
• When inserting the batteries, be careful to do so in
the proper direction, following the + and - marks in
the remote control unit’s battery compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please comply
with governmental regulations or environmental
public instruction’s rules that apply in your country
or area.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with correct
and
polarity.
3.
Close the cover until it clicks.
Remote-controllable range
SR4001/SR5001
.5
ox
ppr
m
INPUT
SELEC
AV
TOR
SURRO
UND
RECEIV
ER
SR5001
MULT
I
STANDBY
POWE
R
M.
ON/OF
F
A
SPEAK
ER
B
SURRO
MODE
UND
PHONE
S
PURE
DIREC
T
SIMPL
SETUP
E
AUTO
HT-EQ
MENU
VOLUM
E
DISPL
ENTER
AY
MEMO
RY
DOWN
CLEAR
EXIT
BAND
T-MOD
E
MUTE
UP
DIGITA
L
7.1CH
INPUT
S-VIDE
O
AUX
VIDEO 1
INPUT
L
AUDIO
R
60°
SYS
TEM
REM
CON
R
TRO
500S
RC5
OTE
LLE
R
Remote control unit (RC5001SR)
ENGLISH
OPERATION OF REMOTE CONTROL UNIT
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
11
ENGLISH
GENERAL INFORMATION OF RC5001SR TO SR4001/SR5001
To control the SR4001/SR5001 by your RC5001SR, you have to select the device AMP or TUNER by pressing
the SOURCE button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
TUNER MODE
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
SLEEP
AUTO
LIP SYNC/
INPUT
dts
1
2
3
BAND
EX/ES
VIRTUAL
T.MODE
5
6
STEREO
NIGHT
CS
4
M-CH ST
7
8
9
7.1CH IN
A/D
HT-EQ
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
MEMO
VOLUME
INFO
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
-
T.DISP
PRESET
DISC+
+
PTY
-
F.DIRECT
TUNING
ANGLE
SUB TITLE
CH-SEL
+
AUDIO
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
TREBLE
REMOTE CONTROLLER
RC5001SR
SOURCE ON / OFF
POWER OFF
POWER ON
SLEEP
DISPLAY
P.DIRECT
SURROUND
AUTO (1)
DOLBY (2)
dts (3)
CSII (4)
EX/ES (5)
VIRTUAL (6)
M-CH ST (7)
STEREO (8)
NIGHT (9)
7.1CH IN (0)
A/D (+10)
LIP SYNC / INPUT
HT-EQ
SPKR A / B
MULTI / CAT
MUTE
M-SPKR
VOLUME 3 / 4
INFO
MENU
ENTER
CURSOR
T.TONE / SET UP
EXIT
CH-SEL
V-OFF
ATT.
BASS 3 / 4
TREBLE 3 / 4
SOURCE
12
Turns the SR4001/SR5001 on and off
Turns the SR4001/SR5001 off
Turns the SR4001/SR5001 on
Sets the sleep timer function
Changes the front display mode
Selects the pure direct mode
Selects the surround mode
Selects auto surround
Selects DOLBY mode
Selects dts mode
Selects CSII mode
Selects EX/ES
Selects VIRTUAL mode
Selects Multi Channel Stereo
Selects STEREO mode
Turns on or off NIGHT mode
Selects the 7.1CH IN
Switches between the analog or digital inputs
Selects the LIP SYNC mode
Turns on or off HT-EQ mode
Selects the speaker system
Turns on or off multi room
Decreases the sound temporarily
Turns on or off multi speaker
Adjusts the over all sound level
Turns on or off the "On Screen Display"
Displays the current setting on the monitor
Enters the "On Screen Display"
Confirms the setting in "On Screen Display" mode
Moves the cursor for setting in "On Screen Display" mode
Enters the test tone menu
Exits from SETUP MENU
Calls up SETUP MENU and adjusts speaker levels or 7.1ch input level
Turns on or off video output
Reduces the input level
Adjusts the tone control of low frequency sound
Adjusts the tone control of high frequency sound
Selects a particular source component
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
SLEEP
AUTO
LIP SYNC/
INPUT
dts
1
2
3
BAND
EX/ES
VIRTUAL
T.MODE
5
6
STEREO
NIGHT
CS
4
M-CH ST
7
8
9
7.1CH IN
A/D
HT-EQ
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
MEMO
VOLUME
INFO
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
-
T.DISP
PRESET
DISC+
+
PTY
-
F.DIRECT
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
+
AUDIO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
DSS
0-9
BAND
T.MODE
P.SCAN
CL
MEMO
INFO
T.DISP
F.DIRECT
PRESET 3 / 4
TUNING 3 / 4
MULTI/CAT
CH/CAT
Inputs the numeric
Selects a radio band
Selects the auto stereo mode or mono mode
Starts preset scan
Clears the inputting
Enters the tuner preset memory numbers
Shows preset information
Selects the display mode in XM
Selects the “Frequency direct input”
Selects a preset station up and down
Tunes a frequency station up and down
Turns XM Category Search mode ON/OFF
Switches categories in Category Search mode
1.
2.
Press the desired SOURCE button.
Press the desired operation buttons to play the selected component.
• For details, refer to the component’s user guide.
• It may not be possible to operate some models.
CONTROLLING A MARANTZ DVD PLAYER (DVD MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
CH/ CAT
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
CL
M-SPKR
INFO
MENU
ENTER
T.TONE
/SET UP
EXIT
REC
SOURCE ON / OFF
POWER OFF
POWER ON
0-9,+10
CL
MEMO
INFO
MENU
ENTER
CURSOR
VOLUME
MULTI/ CAT
-
ENGLISH
CONTROLLING MARANTZ COMPONENTS
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
V-OFF
ATT.
TV
DVD
VCR
AUDIO
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
TREBLE
REMOTE CONTROLLER
RC5001SR
Pause
Play
Stop
Previous/Next
+
CH-SEL
BASS
T.TONE / SET UP
EXIT
T.Tone/Set up
Rewind/ Forward
DISC+
ANGLE
SUBTITLE
AUDIO
Turns the DVD player on and off
Turns the DVD player off
Turns the DVD player on
Inputs the numeric
Clears the inputting
Calls up programming menu
Displays the disc information
Calls up the menu of DVD disc
Enters the setting
Moves the cursor for setting in
"On Screen Display" mode
Enters the test tone menu
Exits from SETUP MENU
Calls up the setup menu of the
DVD player
Pause
Play
Stop
Skips forward or previous
chapter/track
Searchs forward or backward
DVD changer next disc
Selects the camera angle
Selects the subtitle language
Selects the audio language
CONTROLLING A MARANTZ CD (CD MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
VOLUME
INFO
MENU
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
INFO
MENU
Pause
Play
Stop
Previous/ Next
Rewind/ Forward
DISC+
Turns the CD player on and off
Turns the CD player off
Turns the CD player on
Inputs the numeric
Clears the inputting
Programs
Scrolls the disc information
Switches the display information
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
CD changer next disc
CONTROLLING A MARANTZ VCR (VCR MODE)
LEARN
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
CS
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
9
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
VOLUME
INFO
MENU
ENTER
EXIT
-
T.DISP
PRESET
+
P.SCAN
8
7.1CH IN
ENTER
T.TONE
/SET UP
REC
SEND
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
TAPE
AUX1
AUX2
BASS
AUDIO
T.TONE
/SET UP
EXIT
REC
-
PRESET
+
PTY
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
V-OFF
ATT.
TV
DVD
VCR
MD
TUNER
CD
CDR
MD
AMP
TAPE
AUX1
AUX2
AMP
BASS
EXIT
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
AUDIO
Turns the VCR on and off
Inputs the numeric
Selects TV/VCR
Clears the inputting
Calls up programming menu
Selects VCR channel up or down
Calls up the menu
Enters the setting
Moves the cursor for setting in
"On Screen Display" mode
Exits the programming menu
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
Selects the audio language
+
CH-SEL
TREBLE
REMOTE CONTROLLER
RC5001SR
T.DISP
SOURCE ON / OFF
0-9,+10
LIP SYNC/INPUT
CL
MEMO
CH 3 / 4
MENU
ENTER
CURSOR
AUDIO
TREBLE
DSS
REMOTE CONTROLLER
RC5001SR
13
ENGLISH
CONTROLLING A MARANTZ CD RECORDER (CDR MODE)
LEARN
SOURCE
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
BAND
EX/ES
VIRTUAL
T.MODE
5
6
STEREO
NIGHT
CS
4
M-CH ST
7
9
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
P.SCAN
8
7.1CH IN
VOLUME
INFO
MENU
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
INFO
MENU
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
Turns the CD recorder on and off
Turns the CD recorder off
Turns the CD recorder on
Inputs the numeric
Clears the inputting
Programs
Scrolls the disc information
Switches the display information
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
CONTROLLING A MARANTZ MD DECK (MD MODE)
LEARN
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
EX/ES
VIRTUAL
5
6
STEREO
NIGHT
CS
4
M-CH ST
7
9
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
VOLUME
INFO
-
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
TAPE
AUX1
AUX2
BASS
Turns the MD deck on and off
Turns the MD deck off
Turns the MD deck on
Inputs the numeric
Clears the inputting
Programs
Switches the display information
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
LEARN
SOURCE
AUDIO
REC
-
T.DISP
PRESET
+
SEND
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
2
3
EX/ES
VIRTUAL
5
6
STEREO
NIGHT
CS
4
M-CH ST
7
CH/ CAT
INFO
EXIT
T.TONE
/SET UP
T.MODE
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
MENU
VOLUME
MENU
ENTER
T.TONE
/SET UP
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
MD
TUNER
CD
CDR
AMP
TAPE
AUX1
AUX2
TREBLE
REMOTE CONTROLLER
RC5001SR
14
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
MENU
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
ENTER
EXIT
T.DISP
P.SCAN
8
CL
CH/ CAT
T.MODE
7.1CH IN
ENTER
T.TONE
/SET UP
REC
SEND
CONTROLLING A MARANTZ TAPE DECK (TAPE MODE)
BASS
AUDIO
EXIT
REC
-
PRESET
+
PTY
-
F.DIRECT
TUNING
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
MD
TUNER
CD
CDR
MD
AMP
TAPE
AUX1
AUX2
AMP
TREBLE
REMOTE CONTROLLER
RC5001SR
T.DISP
BASS
AUDIO
TREBLE
REMOTE CONTROLLER
RC5001SR
DSS
SOURCE ON / OFF
POWER OFF
POWER ON
0-9
CL
MEMO
REC
Pause
Play
Stop
Previous / Next
Rewind / Forward
Turns the TAPE deck on and off
Turns the TAPE deck off
Turns the TAPE deck on
Inputs the numeric
Clears the inputting
Programs
Record
Pause
Play
Stop
Skips forward or previous track
Searchs forward or backward
NORMAL MODE
(When operating Marantz AV equipment products)
This remote control is preset with a total of 12 types
of remote codes, including Marantz TV (television),
DVD, VCR (VCR deck), DSS (satellite broadcasting
tuner), TUNER, CD, CD-R, MD, TAPE (tape deck),
AUX1, AUX2, and AMP (amplifier).
Learning is not necessary for Marantz products. You
can use these products without setting any codes.
Importants:
• Some codes may be not match your equipment.
In this case, you can use LEARN mode to store these
codes.
• The preset codes do not cover full functions.
If you need extra function, use LEARN mode to
store extra function.
• Wen the batteries are getting weak, the preset
procedure is not successful.
PRESET
+
-
TUNING
Press the SOURCE button.
For this example, press DVD.
Pressing the SOURCE button once changes
the remote control to the settings for the source
that was pressed.
To change the amplifier on other source, press
the SOURCE button twice (double-click). The
code is sent, and then the amplifier source
changes to DVD.
ANGLE
SUB TITLE
V-OFF
ATT.
DVD
VCR
AUDIO
1.
SLEEP
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
DSS
2
3
EX/ES
VIRTUAL
4
5
6
TUNER
CD
CDR
MD
M-CH ST
STEREO
NIGHT
TAPE
AUX1
AUX2
AMP
2.
7
CL
REMOTE CONTROLLER
RC5001SR
CH/ CAT
See the attached manufacturer number list for the
preset manufacturers, devices, preset numbers, and
other settings.
Remote control
source name
TV
DVD
VCR
DSS
Corresponding preset
code
TV
DVD
VCR
SATELLITE
2.
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
SEND
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
SOURCE
VOLUME
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
3.
l/
1.
LIP SYNC/
INPUT
dts
CS
2
3
EX/ES
VIRTUAL
4
5
6
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
BASS
T.MODE
3.
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
AUTO
dts
2
3
EX/ES
VIRTUAL
1
DVD
VCR
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CL
CH/ CAT
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
P.SCAN
DISPLAY
P.DIRECT
SURROUND
SLEEP
1.
dts
LIP SYNC/
INPUT
AUTO
AUTO
1
2
1
3
CS
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
AUDIO
ON
DISPLAY
P.DIRECT
SURROUND
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
2.
3
VIRTUAL
4
5
6
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
TREBLE
DVD
dts
2
EX/ES
M-CH ST
CL
1.
OFF
l/
SLEEP
TV
SEND
SET
CH/ CAT
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
LIP SYNC/
INPUT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
dts
LIP SYNC/
INPUT
2
3
EX/ES
VIRTUAL
5
6
M-CH ST
STEREO
NIGHT
AUTO
2
3
4.
7
ANGLE
SUB TITLE
V-OFF
ATT.
DVD
VCR
CH-SEL
BASS
TV
1.
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
HT-EQ
AUDIO
TREBLE
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
INFO
2.
Press and hold down the SOURCE button
for appliance which should be controlled and
press SET button until the SEND indicator
blinking twice.
Then back light flushes.
2.
Press the below codes to reset.
TV : 1000
DVD : 2000
VCR : 3000
DSS : 4000
P.SCAN
MEMO
MENU
MENU
1.
T.MODE
VOLUME
INFO
ENTER
T.TONE
/SET UP
EXIT
REMOTE CONTROLLER
RC5001SR
1.
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking twice
then back light flushes.
2.
Press the INFO button.
The indicator will blink twice.
Note:
After this procedure, the selected SOURCE button is
set initial code.
HT-EQ
INFO
To view the code for first digit, press 1 once.
Wait 3 seconds, count the SEND indicator
blinks (e.g. 3 blinks = 3) and write down the
number.
Note:
If a code digit is “0”, the SEND indicator will not
blink.
MEMO
VOLUME
DSS
5.
ON
SURROUND
4
CS
SLEEP
DISC+
LIP SYNC/
INPUT
T.MODE
TREBLE
TV
TUNER
REMOTE CONTROLLER
RC5001SR
1.
AUDIO
OFF
P.DIRECT
AUTO
CH/ CAT
l/
SLEEP
1
Device name
Television
DVD player
Video deck
Satellite broadcasting
tuner equipment
SLEEP
3.
CS
1
2.
3.
l/
AUTO
SOURCE
The SEND indicator will blink twice.
SOURCE
SEND
SET
DISPLAY
l/
SCANNING THE CODE TABLE
SLEEP
ON
REMOTE CONTROLLER
RC5001SR
SOURCE
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
SOURCE
OFF
l/
CHECKING THE CODE
LEARN
Press and hold down the SOURCE button for the
appliance which should be controlled and press
SET button until the SEND indicator blinks twice.
Then back light flushes.
Press the 4-digit code for appliance (code table
at the end of this book)
When the procedure is successful, the SEND
indicator will blink twice.
LEARN
LEARN
SEND
SET
BASS
Press ENTER button once to lock in the code.
CL
2.
LEARN
Stop when the appliance turns off.
T.MODE
PRESET MODE
(When operating non-Marantz AV equipment
products)
This remote control is preset with remote control
codes from AV equipment by other manufacturers.
The preset codes are TV, VCR, DVD and DSS.
Settings can be made in one of two ways.
When the preset codes are set, the following codes
are contained in the source button of the remote
control.
Aim the remote control at the appliance and
slowly alternate between pressing CH+ button
and the SOURCE ON/OFF button for the
appliance.
1
1.
RESETTING THE CODE
SOURCE
TREBLE
CS
1.
SET
l/
1
BASS
TV
SETTING THE BACK LIGHT
Each time press the buttons, illuminate button 2
seconds.
To turn off back light, press and hold down the SET
and OFF button until SEND indicator blinks twice.
To turn on it again, press and hold down the SET and
ON button until SEND indicator blinks twice.
Initial is back light ON.
DISC+
CH-SEL
Press and hold down the SOURCE button for
appliance which should be controlled and press
SET button until the SEND indicator blinking
twice. Then back light flushes.
+
SOURCE
1.
3.
4.
5.
PROGRAMMING WITH THE 4-DIGIT CODE
-
2.
ENGLISH
BASIC OPERATION
MENU
4.
Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.
ENTER
T.TONE
/SET UP
EXIT
Switch on the appliance which should be
controlled.
15
ENGLISH
LEARN MODE
4.
This remote control is capable of learning and storing
codes used by other remote controls that you already
own.
For codes which are not learned, the remote control
will transmit either the Marantz preset codes from
the initial settings, or remote codes from another
manufacturer’s AV equipment which is set by the
customer.
The receiver sensor for the remote control signals is
located at the top of the remote control.
1.
Place the remote controller so that its infrared
signal transmitter is facing the infrared signal
receiver on the Marantz remote controller at a
distance of about 2 inches (0.05 m).
Select the SOURCE button to select the button
to be erased.
BASS
3.
TREBLE
l/
SLEEP
DISPLAY
AUTO
1
CS
4
5.
Notes:
• This remote control is capable to learn around 60
codes.
• When the batteries are getting weak , the learing
procedure is not successful.
LEARNING PROCEDURE
2.
Select the button to be learned.
• LEARN indicator lights up.
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
2
3
EX/ES
VIRTUAL
5
6
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
DSS
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
T.MODE
REMOTE CONTROLLER
RC5001SR
Press and hold the button of the original remote
controller to learn until the SEND indicator
blinks twice.
• When the SEND indicator blinks once,
repeat this step.
• When the memory of the RC5001SR is
full, the LEARN and SEND indicators blink
once. If you want to learn the code, you
should erase other learned button.
6.
Repeat steps 4 and 5 to learn other buttons in
same SOURCE.
7.
8.
Repeat steps 3 to 6 to learn other SOURCE.
3.
INFO
Press and hold down the SLEEP button and
press the learned button twice to be erased.
• SEND indicator blinks twice and the mode
returns to LEARN mode.
ENTER
T.TONE
/SET UP
4.
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
4.
2
MENU
EXIT
To return the NORMAL mode, press the SET
button.
Erasing the all SOURCES
3
1.
To return the NORMAL mode, press the SET
button.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
MULTI/ CAT
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
M-SPKR
l/
When you have finished programming the
remote controller, press the SET button, then
LEARN indicator stops blinking and exits from
the LEARN mode.
SLEEP
Erasing the code by SOURCE
1.
AUTO
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
MULTI/ CAT
LEARN
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
1
2.
M-SPKR
SEND
SOURCE
l/
SLEEP
5
0.0
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
m
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
1
AUTO
2
INFO
MENU
3
2
INFO
3
MENU
ENTER
Press and hold down the SLEEP button and
press POWER ON and POWER OFF button.
• LEARN indicator lights.
ENTER
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SY
ST
EM
RE
MO
RC55
00SR
TE
CO
NT
RO
LLE
R
2.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
MULTI/ CAT
SOURCE
SET
OFF
M-SPKR
ON
l/
SLEEP
3.
2
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
INFO
3
Press and hold down the SLEEP button and
press the learned SOURCE button twice to be
erased.
• LEARN indicator lights.
CH-SEL
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
1
MENU
ENTER
Select the SOURCE button to select the
SOURCE.
BASS
2
3
V-OFF
ATT.
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
BASS
AUTO
1
3.
TREBLE
DSS
ERASING PROGRAMMED CODES
(RETURNING TO INITIAL SETTINGS)
2
3
Press ENTER button to continue erasing.
• The SEND indicator blinks twice and the
mode returns to LEARN mode.
• To cancel the erasing operation, do not
press ENTER button and simply touch any
other button.
INFO
Codes can be erased in three ways: by buttons,
sources, and by all memory contents.
MENU
ENTER
T.TONE
/SET UP
EXIT
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
Erasing the code by buttons
1.
Press and hold down the SET and MENU
buttons until LEARN indicator blinks.
REMOTE CONTROLLER
RC5001SR
MULTI/ CAT
SOURCE
SET
OFF
ON
SLEEP
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
1
2
3
4.
To return the NORMAL mode, press the SET
button.
M-SPKR
l/
16
2.
AUTO
DISPLAY
AUTO
1
Notes:
• When the SEND indicator blinks once again, the
transmitting code is unavailable for RC5001SR, or
the transmitting signal is intercepted by noise.
• If no buttons are pressed for approximately 1
minutes while in the LEARN mode, the remote
controller automatically exits from the LEARN
mode.
SLEEP
INFO
MENU
ENTER
Note:
Erasing codes will return to the factory preset code,
or there will leave empty if the button has no factory
preset code.
SPEAKER PLACEMENT
The ideal surround speaker system for this unit is 7speaker systems, using front left and right speakers,
a center speaker, surround left and right speakers,
a surround back left and right speakers, and a
subwoofer.
For best results we recommend that all front speakers
be of the same type, with identical or similar driver
units. This will deliver smooth pans across the front
sound stage as the action moves from side to side.
Your center channel speaker is very important as
over 80% of the dialog from a typical motion picture
emanates from the center channel.
It should possess similar sonic characteristics to the
main speakers. Surround channel speakers need not
be identical to the front channel speakers, but they
should be of high quality.
The surround center speaker is useful for playback
of Dolby Digital Surround EX or DTS-ES. One of
the benefits of both Dolby Digital and DTS is that
surround channels are discrete full range, while they
were frequency limited in earlier “Pro Logic’ type
systems.
Bass effects are an important part of home theater.
For optimal enjoyment a subwoofer should be used
as it is optimized for low frequency reproduction. If
you have full range front speakers, however, they
may be used in place of a subwoofer with proper
setting of the switches in the menu system.
Surround Left
Surround left and right speakers
When the SR4001/SR5001 is used in surround
operation, the preferred location for surround
speakers is on the side walls of the room, at or
slightly behind the listening position.
The center of the speaker should face into the
room.
INVERT
OUTPUT
BTL
EXT. CONT. IN
REMOTE CONT.
MASTER SLAVE
MAX
VIDEO/
+5~13V DC
SYSTEM OUT
SPEAKER SYSTEM
MINIMUM 4 OHMS
INPUT
1
VIDEO
SL
C
HDMI Ver 1.1
MONITOR
OUT 2
AM
TV
L
COMPONENT
VIDEO
INPUT
3
S-VIDEO
GND
ANTENNA
Subwoofer
We recommend using a sub-woofer to have maximum
bass effect. Sub-woofer bears only low frequency
range so you can place it any where in the room.
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
CB/PB
Y
4
COAX
INPUT 1
CR/PR
IN
INPUT 2
OUTPUT
XM
L
R
R
(AUX2)
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
FLASHER
DC
IN
TRIGER
AUDIO
RS-232C
SPEAKER C
UNSWITCHED
1.25A 150W
OFF ON
HEIGHT OF THE SPEAKER UNITS
L
SL
C
SBL
AC IN
R
Front left and right speakers, and a center speaker
Align the tweeters and mid-range drivers on the
three front speakers at the same height, as best as
possible.
L
R
L
R
L
R
L
MODEL NO. SR5001
FRONT B
R
SR
SW
PRE OUT
SBR
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
SURROUND
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
Surround left and right speakers, and surround
back speaker
Place the surround left, right and surround back
speakers higher than your ears by about 70cm – 1m.
Also place the speakers at the same height, as best
as possible.
Center
70cm
1m
Right
Left
Front A
22°
Front Right
1.
Strip away approx. 3/8 inch (10 mm) of wire
insulation.
2.
Twist the bared wire ends tight, to prevent short
circuits.
3.
4.
Loosen the knob by turning it counterclockwise.
90°
Note:
Use magnetically-shielded speakers for front left, right
and the center speakers when the speakers are installed
near the TV and the TV is a monitor type.
Right
Left
Surround
SR5001 only
CONNECTING SPEAKER WIRE
30°
Front left and right speakers
We recommend to set the front L and R speakers
with 45-60 degrees from the listening position.
or
IN
OUT
F US E
FM (75Ω)
0°
150°
INPUT
LEVEL
MIN
Surround back left and right speakers
Surround back speakers are required when a full 7.1channel system is installed.
Speakers should be placed on a rear wall, behind the
listening position.
The center of the speaker should face into the
room.
Front Center
Surround Back
Right
INPUT
Surround
BACK
Right
Left
Powered
subwoofer
Power
Amplifier
Right
Left
Front B
Front Left
Surround Right
Passive
subwoofer
Subwoofer
Surround Back
Left
135°
110°
CONNECTING SPEAKERS
ENGLISH
CONNECTIONS
5.
1.
2.
3/8 inch
(10 mm)
3.
4.
5.
Insert the bare part of the wire into the hole in
side of each terminal.
Tighten the knob by turning it clockwise to
secure the wire.
Center speaker
Align the front line of the center speaker with the front
L/R speakers. Or place the center speaker a little
backward from the line.
17
Note:
Be sure to connect the positive and negative cables for
the speaker properly. If they are miss-connected, the
signal phase will be reversed and the signal quality
will be corrupted.
CONNECTING AUDIO COMPONENTS
DIGITAL
INPUT
DIGITAL
OUTPUT
Tape Deck
CD player
CD recorder
DIGITAL OUT
OUTPUT
L
L
L
R
R
R
OUT IN
OUT IN
L
L
R
R
L R
L R
L R
Analog Audio
L R
R L
R L
R L
INPUT
1
VIDEO
FM (75Ω)
INPUT
3
GND
MONITOR
OUT 2
AM
TV
SL
C
Digital Audio (coaxial)
COMPONENT
VIDEO
S-VIDEO
ANTENNA
L
L R
L R
ENGLISH
Caution:
• Be sure to use speakers with the specified impedance
as shown on the rear panel of this unit.
• To prevent damage to circuitry, do not let the bare
speaker wires touch each other and do not let them
touch any metal
part of this unit.
• Do not touch the
speaker terminals
when the power is
on. It may cause
you to receive an
electric shocks.
• Do not connect more than one speaker cable to one
speaker terminal. Doing so may damage this unit.
DVD
VCR IN
INPUT
2
VCR OUT DSS/VCR2 MONITOR OUT
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
Y
4
CB/PB
COAX
CR/PR
IN
L
Digital Audio (optical)
R
R
(AUX2)
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
FLA
AUDIO
RS-232C
SPEAKER C
OFF ON
CONNECTING A SUBWOOFER
L
SL
C
UNSWITCHED
1.25A 150W
SBL
R
Use the PRE OUT SUBWOOFER jack to connect a
powered subwoofer (power amplifier built in).
If your subwoofer is a passive type (power amplifier
is not built in), connect a monaural power amplifier to
the PRE OUT SUBWOOFER jack and connect the
subwoofer to the amplifier.
L
FRONT B
R
SR
SW
PRE OUT
SBR
L
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
R
L
R
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
R L
The output audio signal from the TAPE OUT jack and
the CD-R/MD OUT jack is the same signal which is
currently selected.
Caution:
Do not connect this unit and other components to mains
power until all connections between components have
been completed.
Notes:
• Insert all plugs and connectors securely. Incomplete
connections may make noise.
• Be sure to connect the left and right channels
properly.
Red connectors are for the R (right) channel, and
white connectors are for the L (left) channel.
• Be sure to connect input and output properly.
• Refer to the instructions for each component that is
connected to this unit.
• Do not bind audio/video connection cables with
power cords and speaker cables this will result in
generating a hum or other noise.
18
R
L
SURROUND
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
R L
CONNECTING DIGITAL AUDIO COMPONENTS
• There are 4 digital inputs, 2 coaxial jacks and
2 optical jacks, on the rear panel. You can use
these jacks to input PCM, Dolby Digital and DTS
bitstream signals from a CD, DVD, or other digital
source components.
• There is one digital output coaxial jack and one
optical output jack on the rear panel. These jacks
can be connected to a CD recorder-, or a MD deck
inputs, respectively.
• Refer to the instructions for each component. To
setup the digital audio format of DVD player, or
other digital source’s connected to digital input
jacks.
• Use fiber optical cables (optical) for DIG-1,2,3
input jacks. Use 75 ohms coaxial cables (for digital
audio or video) for DIG-4,5 input jacks.
• You can designate the input for each digital input/
output jacks according to your component. See
page 26.
Notes:
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator Dolby Digital decoder
when connecting the Dolby Digital RF output jack
of the video disc player to the digital input jack.
• The digital signal jacks on this unit conform to
the EIA standard. If you use a cable that does not
conform to this standard, this unit may not function
properly.
• Each type of audio jack works independently.
Signals input through the digital and analog jacks are
output through the corresponding digital and analog
jacks, respectively.
There are 3 types of video jacks on the rear panel.
DVD player
DIGITAL
OUT
COMPONENT
VIDEO OUT
S-VIDEO VIDEO
OUT
OUT
AUDIO
OUT
Satellite Tuner
VIDEO PROJECTOR
Y
Y
CB / PB CR / PR
S-VIDEO
OUT
S-VIDEO jack
The video signal is separated into luminance (Y) and
color (C) signals for the S-VIDEO jack. The S-VIDEO
signals enables high-quality color reproduction. If
your video component has an S-VIDEO output, we
recommend to use it. Connect the S-VIDEO output
jack on your video component to the S-VIDEO input
jack on this unit.
DIGITAL
OUT
CB / PB CR / PR
L R
L R
L
L
VIDEO
OUT
AUDIO
OUT
COMPONENT S-VIDEO
VIDEO IN
IN
VIDEO jack
The video signal for the VIDEO jacks is the
conventional composite video signal.
R
R
R L
INPUT
1
VIDEO
FM (75Ω)
COMPONENT
VIDEO
GND
AM
TV
SL
C
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
Y
4
CB/PB
COAX
FM (75Ω)
L
R
R
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
AM
TV
L
FLA
SL
R
(AUX2)
C
SR
SW
7.1CH INPUT
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
C
RS-232C
UNSWITCHED
1.25A 150W
SBL
L
R
L
R
FRONT B
SR
SW
SBR
PRE OUT
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
L R
L R
R
L
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
R
SBR
MULTI.
OUT
SL
C
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
SURROUND
R
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
L
R
FRONT B
R
SR
SW
PRE OUT
SBR
L
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
R
L
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
1
CR/PR
R
2
DIGITAL IN
L
SURROUND
CENTER
SPEAKER
SYSTEMS
Video
L R
L R
L R
S-VIDEO
AUDIO
OUT
AUDIO
IN
L R
L R
L R
Analog Audio
VIDEO
OUT IN
Digital Audio
(coaxial)
VIDEO
OUT
Analog Audio
AUDIO
OUT
S-VIDEO
IN
VIDEO
IN
Digital Audio
(coaxial)
L R
Digital Audio
(optical)
Digital Audio
(optical)
Y
4
R L
S-VIDEO
VCR
IN
OUT
CDR/MD
CB/PB
3
SBL
L
Video
S-VIDEO
OUT IN
Y
SPEAKER C
OFF ON
L R
R
L
CR/PR
L R
SL
CB/PB
Y
AUDIO
SPEAKER C
OFF ON
L
INPUT
2
SBL
AUDIO
RS-232C
INPUT
3
S-VIDEO
GND
ANTENNA
CR/PR
IN
L
R
(AUX2)
INPUT
1
VIDEO
MONITOR
OUT 2
ANTENNA
L
INPUT
3
S-VIDEO
ENGLISH
VIDEO, S-VIDEO , COMPONENT JACKS
CONNECTING VIDEO COMPONENTS
3
Component jack
Make component video connections to a TV or
monitor with component inputs to produce higher
quality video images. Use a component video cable
or 3 video cords to connect the component video out
jacks on the SR4001/SR5001 to the monitor.
Notes:
• Be sure to connect the left and right audio channels
properly.
Red connectors are for the R (right) channel, and
white connectors are the for L (left) channel.
• Be sure to connect the inputs and outputs of the
video signals properly.
• If you connect the S-VIDEO or component signal
to the S-VIDEO or component jack on this unit, it
is not necessary to connect the conventional video
signal to the VIDEO (composite) jack. If you use
both video inputs, this unit gives priority to the SVIDEO signal.
• Each type of video jack works independently.
Signals input to the VIDEO (composite) and SVIDEO jacks or component are output to the
corresponding VIDEO (composite) and S-VIDEO
or component jacks, respectively.
• This unit has the “TV-AUTO ON/OFF” function to
turn the TV ON or OFF automatically, by sensing
the incoming video signal from the VIDEO jacks.
• You may need to setup the digital audio output
format of your DVD player, or other digital source
components. Refer to the instructions of the each
component connected to the digital input jacks.
• There is no Dolby Digital RF input jack. Please use
an external RF demodulator with a Dolby Digital
decoder to connect a video disc player which has a
Dolby Digital RF output jack to the digital input jack
on this unit.
TV
19
ENGLISH
ADVANCED CONNECTING
CONNECTING THE REMOTE CONTROL JACKS
INPUT
1
INPUT
3
COMPONENT
VIDEO
MONITOR
OUT 2
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
Y
CB/PB
3
CR/PR
CB/PB
Y
4
COAX
INPUT 1
CR/PR
IN
2
RC OUT
IN
R L
R L
R L
R L
DVD
R L
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
1
IN
OUT
CDR/MD
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
FLASHER
DC
IN
TRIGER
OPTION
AUDIO
R L
R L
R L
R L
L
R
L
R
L
R
L
VIDEO
CENTER
FM (75Ω)
L
CENTER
S-VIDEO
GND
AM
ANTENNA
TV
L
R
FRONT SURR.
SL
C
DVD
L
SURR.
BACK
SUB
WOOFER
R
FRONT SURR.
R
R
(AUX2)
SR
SW
7.1CH INPUT
RS-232C
SBR
MULTI.
OUT
SL
TV
DVD
Power
Amplifer
UNSWITCHED
1.25A 150W
L
SW
SBR
PRE OUT
L R
L R
1
AC OUTLET
230V
50/60Hz
SWITCHED
0.65A 150W
REMOTE
CONTROL
CD recorder
REMOTE
CONTROL
MD deck
REMOTE
CONTROL
CD player
IN
IN
IN
OUT
OUT
OUT
SWITCHED
1.25A 150W
FRONT B
SR
CENTER
SPEAKER
SYSTEMS
SUB
WOOFER
Subwoofer
R
SURROUND
SBL
R
DVD Audio player
or
Super Audio CD Multi
channel player
SURR.
BACK
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
VC
SPEAKER C
C
FRONT A
IN
OFF ON
L
TB
B.CENTER.
BACK : 6-8 OHMS
: 8 OHMS
L
VCR IN
SBL
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIM
FRONT A AND B:MINIMU
AC OUTLETS
120V 60Hz
EXTERNAL INTERNAL
EXTERNAL INTERNAL
EXTERNAL INTERNAL
L R
Front
Front
Center
Right
Left
Surround
Surround
Left
Right
Surround
Back Left
Surround
Back Right
CONNECTING MULTI CHANNEL AUDIO SOURCE
CONNECTING AN EXTERNAL POWER AMPLIFIER
The 7.1CH INPUT jacks are for multichannel audio
source such as a Super Audio CD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the SETUP
MAIN MENU. See page 29.
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the remote
signal only to the unit. Also, if a Marantz power
amplifier (some models excluded) is connected to
one of these terminals, the power amplifier’s, power
switch is synchronized with this unit’s power switch.
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR4001/
SR5001, be sure to always disable operation of
the infrared sensor on the main unit by using the
following procedure.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for this
feature.
1.
Hold down the 7.1CH INPUT (SR4001) / MULTI
(SR5001) button and MENU button on the front
panel at the same time for five seconds.
2.
The setting “IR=ENABLE” is shown on the FL
DISPLAY.
3.
Press the 1 or 2 cursor button to change this to
“IR=DISABLE”.
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
Be sure to set to “IR=ENABLE” when external
infrared sensors or similar devices are not connected.
Otherwise, the main unit will be unable to receive
remote control commands.
5.
20
To restore the original setting, perform steps 1
to 4 to set to “IR=ENABLE”.
AM Loop
Antenna
FM External
Antenna
Connecting the supplied FM antenna
The supplied FM antenna is for indoor use only.
During use, extend the antenna and move it in various
directions until the clearest signal is received.
Fix it with push pins or similar implements in the
position that will cause the least amount of distortion.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
AM External
Antenna
FM Antenna
INPUT
1
VIDEO
FM (75Ω)
GND
COMPONENT
VIDEO
TV
SL
C
HDMI Ver 1.1
MONITOR
OUT 2
AM
ANTENNA
L
INPUT
3
S-VIDEO
DVD
VCR IN
INPUT
2
VCR OUT DSS/VCR2 MONITOR OUT
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
Y
4
CB/PB
COAX
INPUT 1
CR/PR
IN
INPUT 2
OUTPUT
XM
L
R
R
(AUX2)
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OPT
DIGITAL OUT
OUT
RC-5
FLASHER
DC
IN
TRIGER
ENGLISH
CONNECTING THE SUPPLIED ANTENNAS
CONNECTING THE ANTENNA TERMINALS
Connecting the supplied AM loop antenna
The supplied AM loop antenna is for indoor use
only.
Set it in the direction and position it to where you
receive the clearest sound. Put it as far away as
possible from the unit, televisions, speaker cables,
and power cords.
If you experience poor reception quality, an outdoor
antenna may improve the quality.
AUDIO
RS-232C
SPEAKER C
UNSWITCHED
1.25A 150W
OFF ON
L
SL
C
SBL
L
R
L
R
L
R
SR
SW
PRE OUT
SBR
Press and hold down the lever of the AM
antenna terminal.
2.
3.
Insert the bare wire into the antenna terminal.
L
MODEL NO. SR5001
FRONT B
R
1.
AC IN
R
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
SURROUND
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
Release the lever.
CONNECTING AN FM OUTDOOR ANTENNA
ASSEMBLING THE AM LOOP ANTENNA
1.
Release the vinyl tie and take out the connection
line.
4.
Place the antenna on stable surface.
Notes:
• Keep the antenna away from noise sources (neon
signs, busy roads, etc.).
• Do not put the antenna close to power lines. Keep it
well away from power lines, transformers, etc.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
CONNECTING AN AM OUTDOOR ANTENNA
2.
Bend the base part in the reverse direction.
An outdoor antenna will be more effective if it is
stretched horizontally above a window or outside.
Notes:
• Do not remove the AM loop antenna.
• To avoid the risk of lightning and electrical shock,
grounding is necessary.
3.
Insert the hook at the bottom of the loop part
into the slot at the base part.
21
ENGLISH
XM RADIO OVERVIEW (SR5001 only)
SR5001 is the XM Ready® receiver. You can receive XM Satellite Radio® by connecting to the XM Connectand-PlayTM or Possport system (sold separately) and subscribing the XM service.
Introducing XM Satellite Radio
There’s a world of audio listening pleasure beyond AM and FM. XM Satellite Radio which includes:
• Over 170 Digital Channels
• The most commercial-free music in satellite radio
• Live concerts plus exclusive original programming
• The biggest names in news, talk, and entertainment
• The most sports play-by-play
• Major league Baseball. Every team. All season long.
CONNECTING XM CONNECT-AND-PLAY ANTENNA
• Plug the XM Connect-and-Play antenna or Passport system into XM terminal on the rear panel.
• Position the XM antenna near a south-facing window to receive the best signal.
When making connections, also refer to the operating instructions of the XM Connect-and-Play antenna or
Possport system.
XM
INPUT
3
COMPONENT
VIDEO
HDMI Ver 1.1
MONITOR
OUT 2
PB
CR/PR
Y
CB/PB
3
CR/PR
Y
4
CB/PB
COAX
INPUT 1
CR/PR
IN
INPUT 2
OUTPUT
XM
Questions? Visit www.xmradio.com <http://www.xmradio.com/>
IN
OUT
CDR/MD
How to Subscribe
Listeners can subscribe by visiting XM on the Web at www.xmradio.com or by calling XM’s Listener Care at
(800) 967-2346. Customers should have their Radio ID and credit card ready. The Radio ID can be found by
selecting channel 0 on the radio.
(See the “CHECKING THE XM SIGNAL STRENGTH AND RADIO ID”)
1
2
DIGITAL IN
XM $ 12.95 monthly service subscription sold separately. XM Passport system required to receive XM
service (sold separately). Installation costs and other fees and taxes, including a one-time activation fee
may apply. Subscription fee is consumer only. All fees and programming subject to change. Channels with
frequent explicit language are indicated with an XL. Channle blocking is available for XM radio receivers
by calling 1-800-XMRADIO. Subscriptions subject to Customer Agreement available at xmradio.com. XM
service only available in the 48 contiguous United States. [XM Ready, XMDirect*] are trademarks of XM
Satellite Radio Inc. © 2006 XM Satellite Radio Inc. All rights reserved.
22
OPT
DIGITAL OUT
OUT
RC-5
FLASHER
DC
IN
TRIGER
UNSWITCHED
1.25A 150W
AC IN
R
L
MODEL NO. SR5001
SURROUND
CENTER
SPEAKER
SYSTEMS
A Warning Against Reverse Engineering
It is prohibited to copy, decompile, disassemble, reverse engineer, or manipulate any technology incorporated
in receivers compatible with the XM Satellite Radio system.
Furthermore, the AMBE® voice compression software included in this product is protected by intellectual
property rights including patent rights, copyrights, and trade secrets of Digital Voice Systems, Inc. The user of
this or any other software contained in an XM Radio is explicitly prohibited from attempting to copy, decompile,
reverse engineer, or disassemble the object code, or in any other way convert the object code into humanreadable form. The software is licensed solely for use within this product.
3
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
Note
Keep the power supply cord unplugged until the XM Connect-and-Play antenna or Possport system connection have
been completed.
Bi-wire Connection
A bi-wire connection is possible with speakers that
have two sets of inputs (for treble and bass).
This allows you to drive the treble and bass units
with separate channel amps, which enables better
sound quality. Connect the speakers as shown in the
figure. Set the SPEAKER C selector switch on the
rear panel to ON.
(Multi room speaker B)
RIGHT
SPEAKER
ENGLISH
CONNECTING FOR SPEAKER C USE (SR5001 only)
CONNECTING FOR THE MULTI ROOM (SR5001 only)
LEFT
SPEAKER
Notes:
• If incorrectly connected, a protective circuit in the
receiver will trip and set the receiver to standby.
(The STANDBY indicator will flash.) In such case,
recheck the connections between the speakers and
the receiver.
• Turn power to the receiver off before changing the
setting of the SPEAKER C selector switch.
INPUT
1
VIDEO
FM (75Ω)
GND
COM
AM
ANTENNA
TV
L
INPUT
3
S-VIDEO
SL
C
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
INPUT
2
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
CR/PR
Y
4
CB/P
CO
L
R
R
(AUX2)
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
IN
TV
DVD
OUT
VCR1
IN
DSS/VCR2
IN
CD
OUT
TAPE
IN
OUT
CDR/MD
1
2
DIGITAL IN
3
OP
DIGITA
AUDIO
RS-232C
SPEAKER C
OFF ON
SPEAKER C
OFF ON
FM (75Ω)
L
SL
C
INPUT
1
VIDEO
S-VIDEO
GND
AM
ANTENNA
SBL
R
L
R
L
R
L
R
L
L
SL
C
TV
DVD
TV
DVD
VCR IN
VCR OUT DSS/VCR2 MONITOR OUT
IN
IN
DSS/VCR2
INPUT
2
CB/PB
Y
CR/PR
Y
SBL
CB/PB
3
L
FRONT B
R
SR
SW
PRE OUT
SBR
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
SURROUND
MULTIROOM
CENTER
SPEAKER
SYSTEMS
R
R
(AUX2)
SR
SW
7.1CH INPUT
SBR
MULTI.
OUT
OUT
VCR1
IN
CD
OUT
TAPE
1
IN
OUT
CDR/MD
DIG
AUDIO
MULTIROOM
LEFT
SPEAKER
MULTIROOM
RIGHT
SPEAKER
RS-232C
L
SL
SPEAKER C
OFF ON
C
SBL
R
L
R
L
R
L
R
L
L R
FRONT B
R
SR
SW
PRE OUT
SBR
FRONT A
FRONT A OR B,CENTER,
SURR,SURR BACK:MINIMUM 6 OHMS
FRONT A AND B:MINIMUM 8 OHMS
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
SURROUND
CENTER
SPEAKER
SYSTEMS
R L
L
R
FRONT
MAIN AMP
(For multiroom)
Note:
You can use surround back speaker terminals as multi
room speaker terminals when you use no surround
back speaker.
23
ENGLISH
HDMI JACK
This unit has two HDMI inputs and one HDMI output. It
can send digital video and audio signals from DVDs and
other sources directly to a display. It minimizes signal
degradation caused by analog conversion so that high
quality images can be enjoyed.
Select an input source from the OSD menu system.
(See page 26)
Notes:
• When the HDMI output is connected to a display
monitor that does not support HDCP, signals are not
output. To view images in HDMI, it is necessary to
connect to a display that supports HDCP.
• There may be no image output if connected to a
TV or display that is not compatible with the above
format.
• Refer to the instruction manual of the TV or display
to be connected to the SR4001/SR5001 for detailed
information regarding the HDMI terminal.
* HDCP: High-bandwidth Digital Content Protection
• Disconnecting or connecting cables with the power
on can damage the equipment. Turn the power off
before disconnecting or connecting cables.
• Some DVD-Audio disks disable downmixing.
These types of disks are not played back correctly
unless the left, center, right and surround left and
right speakers, and subwoofer are connected.
• If a DVD player that does not support HDMI 1.1
is connected to the SR4001/SR5001, multi channel
PCM playback is not possible even with DVDAudio disks.
• If a DVD player or other device with DVI output is
connected to the SR4001/SR5001, a separate audio
cable (i.Link, optical-digital, coaxial digital or analog)
is needed for the audio signals. In this case, select
the connected audio input as explained in “1 INPUT
SETUP”. (See page 26)
• Multi channel PCM signals and audio signals of 62
kHz or higher that are input from the HDMI jack are
not output from the DIGITAL OUT jacks.
• Depending on the quiality of the cable used, the
HDMI signal may be affected by noise.
• Audio units that use sampling frequencies of 128
kHz and above are not supported.
DVD player
VIDEO PROJECTOR
HDMI INPUT
HDMI OUTPUT
INPUT
1
INPUT
3
COMPONENT
VIDEO
HDMI Ver 1.1
MONITOR
OUT 2
R IN
N
VCR OUT DSS/VCR2 MONITOR OUT
OUT
VCR1
IN
DSS/VCR2
INPUT
2
IN
CD
CB/PB
Y
OUT
TAPE
CR/PR
Y
IN
OUT
CDR/MD
CB/PB
3
1
CR/PR
Y
4
2
DIGITAL IN
CB/PB
COAX
3
OPT
DIGITAL OUT
INPUT 1
CR/PR
IN
OUT
RC-5
FLASHER
DC
IN
TRIGER
AUDIO
UNSWITCHED
1.25A 150W
AC IN
R
L
R
L
R
L
MODEL NO. SR5001
FRONT A
Notes:
• Some HDMI components can be controlled over the
HDMI cable, but this receiver cannot control other
components this way.
• When connected to a monitor (i.e., TV, projector,
etc.) that does not support HDCP, video and audio
are not output.
• DVI cables come with 24-pin and 29-pin plugs. This
receiver supports 24-pin DVI-D cables; 29-pin DVI
cables cannot connect to it.
• Some source devices such as DVD players do not
support HDMI repeater operations like those of
the SR4001/SR5001. In such case, pictures are not
properly projected on monitors such as TVs and
projectors.
• When multiple components are connected to this
receiver, turn power to unused components off to
prevent interference between them.
24
OUTPUT
XM
CONNECTING HDMI DEVICES
An HDMI cable (sold separately) is used to connect the
HDMI jack on the SR4001/SR5001 with the HDMI jack
on a DVD player, TV, projector or other component. To
transmit multichannel audio via HDMI, the connected
player must support multichannel audio transmission
through its HDMI jack.
HDMI video streaming is compatible with DVI in principle.
Therefore, it is possible to connect to a TV or monitor that
has a DVI terminal using an HDMI-DVI conversion cable
or plug. When connecting to a DVI terminal, connect the
audio signal separately.
INPUT 2
TER,
INIMUM 6 OHMS
MUM 8 OHMS
SURROUND BACK
SPEAKER C/
MULTI SPEAKER
SURROUND
CENTER
SPEAKER
SYSTEMS
SWITCHED
1.25A 150W
AC OUTLETS
120V 60Hz
Satellite Tuner
HDMI OUTPUT
After all components are connected, initial setup
must be performed.
ON SCREEN DISPLAY MENU SYSTEM
The SR4001/SR5001 incorporates an on-screen
menu system, which makes various operations
possible by using the cursor (3, 4, 1, 2) and ENTER
buttons on the remote control or on the front panel.
Note:
To view the on-screen displays, make certain you have
made a connection from the Monitor Out jack on the
rear panel to the composite, S-Video, component video
input of your TV or projector. (see page 19)
1.
Press the AMP button of the remote control.(This
step is not needed when operating the setup
menus from the receiver itself.)
2.
Press the MENU button on the remote control
or set to display the “SETUP MAIN MENU” of
the OSD menu system.
There are 8 items in the SETUP MAIN MENU.
3.
Select a desired sub-menu with the 3 or 4
cursor buttons, and press the ENTER button to
enter. The display will change to the selected
sub-menu. You can lock the condition of setup
to each sub-menu with the 1 or 2 or cursor
buttons.
Note:
If you desire to adjust any sub-menu, you need to set
it to UNLOCKED.
4.
If you desire to exit from this menu system,
press the EXIT button, or move the cursor to
EXIT and press the ENTER button.
ENGLISH
SETUP
SETUP MAIN MENU
1-1 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 3 : : DVD :AUTO : 1 : 1
: 1
VCR1:AUTO : - : : 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : F : : MAIN
NEXT
1.
2.
3.
4.
5.
6.
7.
8.
INPUT SETUP
:UNLOCK
SPEAKER SETUP:UNLOCK
PREFERENCE
:UNLOCK
SURROUND
:UNLOCK
PL II MUSIC
:UNLOCK
CS II
:UNLOCK
7.1 CH. INPUT:UNLOCK
MULTI ROOM
:UNLOCK
EXIT
* “8. MULTI ROOM” is displayed only with
the SR5001.
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------CD
:AUTO : 4 :
:
TAPE:AUTO : - :
:
CD-R:AUTO : 5 :
:
AUX2:AUTO : - :
:
3 PREFERENCE
STANDBY MODE
TV-AUTO
OSD INFO
BILINGUAL
VIDEO CONVERT
HDMI
DC TRIGGER
:
:
:
:
NORMAL
DISABLE
ENABLE
MAIN
: ENABLE
MAIN
EXIT
* “DC TRIGGER” is displayed only with the SR5001.
RETURN
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
EXIT
* For the SR4001, “–” is displayed for TV
DIG.
MAIN
4 SURROUND
EXIT
* For the SR4001, “3” is displayed for CDR DIG.
2-1 SPEAKERS SIZE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
2-2 SPEAKERS DISTANCE
FRONT L
: 10
FRONT R
: 10
CENTER
: 10
SURR.L
: 10
SURR.R
: 10
SUB W
: 10
SURR.B L : 10
SURR.B R : 10
MAIN
RETURN
ft
ft
ft
ft
ft
ft
ft
ft
NEXT
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
EXIT
2-3 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
MAIN
EXIT
5 PL II MUSIC PARAMETER
PARAMETER
: DEFAULT
PANORAMA
: OFF
DEMENSION
:
3
CENTER WIDTH :
3
3-1 VIDEO CONVERT
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
MAIN
ON
ON
ON
ON
ON
EXIT
6 CS II PARAMETER
MAIN RETURN
EXIT
TRUBASS
SRS DIALOG
: 0
: 0
SR5001 only
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
MAIN RETURN
CD
:
TAPE :
CD-R :
AUX2 :
TUNER:
7.1CH:
EXIT
SR5001 only
8 MULTI ROOM
AUDIO
: DVD
SLEEP TIMER
: OFF
MULTI:OUT
: STEREO
MULTI:OFF
MSPK
:
VOL
: VARI
LEVEL
: -90dB
--- MAIN ROOM STATUS --VIDEO:DVD
AUDIO:DVD
MAIN
EXIT
MAIN
EXIT
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
25
ENGLISH
1 INPUT SETUP (ASSIGNABLE DIGITAL
INPUT AND COMPONENT VIDEO INPUT)
4 digital inputs and 2 component video inputs can be
assigned to a desired source.
Use this menu to select the digital input jack to be
assigned to the input source.
1.
Select “INPUT SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
1-1 INPUT SETUP
2 SPEAKER SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------TV
:AUTO : 3 : : DVD :AUTO : 1 : 1
: 1
VCR1:AUTO : - : : 3
DSS :AUTO : 2 : 2
: 2
AUX1:AUTO : F : : MAIN
NEXT
Notes:
• When TUNER is fixed to the analog input, you can
not select any digital input.
• When a DTS-LD or DTS-CD is playing, this setup is
not available. This is to avoid noise being generated
from the analog input.
• If “DIG” is selected and a DVD, compact disc or
LD is fast-forwarded during playback, decoded
signals may produce a skipping sound. In such cases,
change the setting to DIGITAL.
EXIT
After you have installed the SR4001/SR5001,
connected all the components, and determined the
speaker layout, it is now time to perform the settings
in the Speaker Setup menu for the optimum sound
acoustics for your environment and speaker layout.
Before you perform the following settings, it is
important that you first determine the following
characteristics:
1-2 INPUT SETUP
FUNC:MODE :DIG:HDMI:COMP
-----------------------CD
:AUTO : 4 :
:
TAPE:AUTO : - :
:
CD-R:AUTO : 5 :
:
AUX2:AUTO : - :
:
MAIN
RETURN
EXIT
2.
To select the input source and MODE, press
the 3 or 4 cursor buttons.
3.
To select “DIG” “HDMI” or “COMP” for the input
jack, press the 1 or 2 cursor buttons.
2-1 SPEAKERS SIZE
When setting the speaker size in the SPEAKER
SIZE sub-menu, use the guidelines given below.
LARGE:
The complete frequency range for the channel you
are setting will be output from the speaker.
SMALL:
Frequencies of the channel you are setting lower
than approx. 100 Hz will be output from the
subwoofer.
If the Subwoofer is set to “NONE” and the front
speakers are set to “LARGE,” then the sound will
be output from both the left and right speakers.
Select “DIG” for input sources, for automatic
detection of the digital input signal condition.
2-1 SPEAKERS SIZE
SUBWOOFER
: YES
FRONT L/R
: LARGE
CENTER
: SMALL
SURROUND L/R
: SMALL
SURR.BACK
: 2CH
SURR.BACK SIZE
: SMALL
LPF/HPF
: 100Hz
BASS MIX
: BOTH
MAIN
NEXT
EXIT
If there is not a digital signal present, but there
is an analog signal present, the analog signal
will be played.
Select “DIG”, when only a digital signal will be
used. Select “ANA” for input sources for which
no digital input jacks are used.
4.
5.
26
To select the vdieo source, select “HDMI” or
“COMP” by pressing the 3 or 4 cursor buttons,
and press the 1 or 2 cursor buttons to select
the vdieo source to be assigned .
After you complete this portion of the set up,
move the cursor to MAIN with the 3 or 4 cursor
buttons and press the ENTER button.
1.
Select “SPEAKER SETUP” in SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
2.
To select the each speaker, press the 3 or 4
cursor buttons.
3.
To select the setting of each speaker size,
press the 1 or 2 cursor buttons.
4.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
SUBWOOFER:
YES:
Select when a subwoofer is connected.
NONE:
Select when a subwoofer is not connected.
FRONT L/R
LARGE:
Select if the front speakers are large.
SMALL:
Select if the front speakers are small.
• If “NONE” is selected for the Subwoofer setting,
then this setting is fixed to “LARGE.”
CENTER
NONE:
Select if no center speaker is connected.
LARGE:
Select if the center speaker is large.
SMALL:
Select if the center speaker is small.
SURROUND L/R
NONE:
Select if no surround left and right speakers are
connected.
LARGE:
Select if the surround left and right speakers are
large.
SMALL:
Select if the surround left and right speakers are
small.
SURR. BACK
NONE:
Select if no surround back left and right speakers
are connected.
2CH:
Select if the surround back left and right speakers
are connected.
1CH:
Select if the one surround back speaker is
connected.
In this case, the audio signal is emitted form the
Surround back L output terminal.
Notes:
• If “NONE” is selected for the Surround L/R setting,
then this setting is fixed to “NONE.”
• You can use surround back speaker terminals as
multi room speaker terminals when you use no
surround back speaker. (See page 23)
SURR. BACK SIZE
LARGE:
Select if the surround back speaker is large.
SMALL:
Select if the surround back speaker is small.
Note:
If “NONE” is selected for the Surround L/R setting,
then this setting is not available.
LPF/HPF
When you use a subwoofer, you can select the cutoff
frequency for the small speakers used. Select one of
the crossover frequency levels according to the size
of the small speaker connected.
80Hz → 100Hz → 120Hz → 150Hz → 180Hz
Notes:
• If using small front speakers, set a slightly higher
frequency. If using large front speakers, set a slightly
lower frequency.
• If Pure-Direct mode, 7.1CH Input is in use, this
function does not take effect.
BASS MIX
• The bass mix setting is only valid when “LARGE”
is set for the front speakers and “YES” is set for the
subwoofer during stereo playback .
This setting has effect only during playback of
PCM or analog stereo sources.
• When “BOTH” is selected, the low frequencies will
be played through the main L&R, as well as the
sub woofer.
In this playback mode, the low frequency range
expand more uniformly through the room, but
depending on the size and shape of the room,
interference may result in a decrease of the actual
volume of the low frequency range.
• By selecting “MIX”, the low frequencies will play
through the main L&R only.
Note:
LFE signals during playback of Dolby Digital or DTS,
will be played through the sub woofer.
Use this parameter to specify the distance of each
speaker’s position from the listening position. The
delay time is automatically calculated according to
these distances.
Begin by determining the ideal or most commonly
used seating position in the room.
This is important for the timing of the acoustics to
create the proper sound space that the SR4001/
SR5001 and today’s sound systems are able to
produce.
Note:
For speakers that you have selected “NONE” the
Speaker Configuration sub-menu will not appear
here. (There are several useful books and special
DVD and LD’s available to guide you through proper
home theater configuration. If you are unsure, have
your Marantz dealer perform the installation for you.
They are trained professionals familiar with even
the most sophisticated custom installations. Marantz
recommends the WWW.CEDIA.ORG website for
further information about this).
2-2 SPEAKERS DISTANCE
FRONT L
: 10
FRONT R
: 10
CENTER
: 10
SURR.L
: 10
SURR.R
: 10
SUB W
: 10
SURR.B L : 10
SURR.B R : 10
MAIN
RETURN
ft
ft
ft
ft
ft
ft
ft
ft
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
3.0 m
EXIT
1.
To select each speaker , press the 3 or 4
cursor buttons.
2.
To set the distance for each speaker , press the
1 or 2 cursor buttons.
3.
After you complete this portion of the set up,
move the cursor to “NEXT” with the 3 or 4
cursor buttons and then press the ENTER
button to go to the next page.
FRONT L:
Set the distance from the front left speaker to your
normal listening position.
CENTER:
Set the distance from the center speaker to your
normal listening position.
FRONT R:
Set the distance from the front right speaker to
your normal listening position.
SURR. L:
Set the distance from the surround left speaker to
your normal listening position.
SURR. R:
Set the distance from the surround right speaker
to your normal listening position.
SUB W:
Set the distance from the subwoofer to your
normal listening position.
SURR. B L:
Set the distance from the surround back left
speaker to your normal listening position.
SURR. B R:
Set the distance from the surround back right
speaker to your normal listening position.
If you select “AUTO” , the test tone will be cycled
through in a circular pattern which is Left → Center →
Right → Surround Right → Surround Back Right →
Surround Back Left → Surround Left → Subwoofer
→ Left → .. increments of 2 seconds
for each channel.
Using the 1 or 2 cursor buttons, adjust the volume
level of the noise from the speaker so that it is the
same level for all the speakers.
Notes:
• Set the distance to each speaker in meters (m) or feet
(ft) as follows.
m: 0.3 - 9 m in 0.3 m steps
ft: 1 - 30 ft in 1 ft steps
• For the speakers that you have selected “NONE” the
Speaker Size menu will not appear.
• The setting for Surr.Back L and Surr.Back R appears
if you set for it to, two surround back speakers in the
Speaker Size menu.
• The setting of Surr.Back appears if it is set for one
surround back speaker in the Speaker Size menu.
Remember the level of this noise and then
press the 4 cursor button.
Note:
The speaker level settings are not available in 7.1
Channel Input mode, CS mode and Multi Channel
Stereo mode.
2-3 SPEAKERS
TEST MODE
FRONT L
CENTER
FRONT R
SURR.R
SURR.B R
SURR.B L
SURR.L
SUB W
MAIN
RETURN
LEVEL
:
MANUAL
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
:
0 dB
EXIT
TEST MODE :
Selects “MANUAL” or “AUTO” for generating
the mode of the test tone with the 1 or 2 cursor
buttons.
3 PREFERENCE
STANDBY MODE
TV-AUTO
OSD INFO
BILINGUAL
VIDEO CONVERT
HDMI
DC TRIGGER
If you select “MANUAL”, adjust the output level of
each speaker as listed below.
1.
When you move the cursor to FRONT L by
pressing the 4 cursor button, the SR4001/
SR5001 will emit a pink noise from the front left
speaker.
(Note that this can be adjusted to any level
between -10 and +10 dB in 1 dB intervals
except the subwoofer setting. The subwoofer
can be adjusted to any level between -15 and
+10 dB in 1 dB intervals.)
The SR4001/SR5001 will now emit the pink
noise from the center speaker.
2.
Using the 1 and 2 cursor buttons, adjust the
volume level of the noise from the center
speaker so that it is the same level as the front
left speaker.
3.
Press the 4 cursor button again. The SR4001/
SR5001 will now emit the pink noise from the
front right speaker.
4.
Repeat steps 2 and 3 above for the front
right and other speakers until all speakers are
adjusted to the same volume level.
2-3. SPEAKERS LEVEL SETTING WITH TEST TONE
Here you will set the volume for each speaker so that
they are all heard by the listener at the same level.
We recommend using a SPL (Sound Pressure Level)
meter, when available.
3 PREFERENCE
After you complete this portion of the set up, press
the ENTER button, the cursor will move to “MAIN”
and then press the ENTER button to go to SETUP
MAIN MENU.
ENGLISH
2-2 SPEAKERS DISTANCE
MAIN
: ECONOMY
:
: ENABLE
: MAIN
: ENABLE
EXIT
1.
Select “PREFERENCE” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select a desired content, press the 3 or 4
cursor buttons.
STANDBY MODE:
When this function is set to “ECONOMY”, you can
reduce the power consumption when the unit is in
the standby mode.
Note:
TV-AUTO and RS-232C are disabled in the
“ECONOMY” setting (SR5001 only).
TV AUTO:
Select the TV AUTO ON/OFF function to enable or
disable with the 1 or 2 cursor buttons.
OSD Info:
Select the OSD information function to enable or
disable with the 1 or 2 cursor buttons.
If you select “ENABLE”, the SR4001/SR5001 will
display the status of the feature (Volume up/down,
input select, etc..) on the TV monitor. But if you do
not desire this information, select “DISABLE”.
BILINGUAL:
In the Bilingual mode, Dolby Digital and DTS
output is set to either “MAIN” or “SUB”. Select
“BILINGUAL” with the 1 and 2 cursor buttons,
then select MAIN ↔ SUB ↔ MAIN+SUB with the
1 or 2 cursor buttons.
Notes:
• Speakers that you selected “NONE” for in the
Speaker Size menu will not appear.
• The setting of Surr.Back L and Surr.Back R appears
if you have set it for two surround back speakers in
the Speaker Size menu.
• The setting of Surr.Back appears if you have set it for
one surround back speaker in the Speaker Size menu.
• To adjust the speaker levels for 7.1-channel input
sources, you will need to use the 7.1CH-INPUT sub
menu. (See page 29).
27
ENGLISH
VIDEO CONVERT:
Select the VIDEO CONVERT function to enable
or disable with the 1 or 2 cursor buttons. (Video
cable connection: Refer to page 19)
3-1 VIDEO CONVERT
TV
DVD
VCR1
DSS
AUX1
:
:
:
:
:
ON
ON
ON
ON
ON
Notes:
• REMOTE is available for the external control. The
RC5001SR cannot operate this function.
• To select desired input source , press 3 or 4 cursor
button.
• To set ON or OFF, press 1 or 2 cursor button.
• After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor
buttons and press the ENTER button.
5 PL II (PRO LOGIC II)
MUSIC PARAMETER
6 CS II (CIRCLE SURROUND II) PARAMETER
6 CS II PARAMETER
Pro Logic II-Music mode creates a rich and enveloping
surround ambience from stereo sources such as
CDs.
In this mode, SR4001/SR5001 includes three controls
to fine-tune the soundfield as follows.
TRUBASS
SRS DIALOG
5 PL II MUSIC PARAMETER
MAIN
MAIN RETURN
EXIT
HDMI AUDIO:
This setting determines whether to playback audio
input to the HDMI jacks through the SR4001/
SR5001 or output it through the receiver to a TV
or projector.
ENABLE: The audio input to the HDMI jacks
can be played back by this receiver.
In such case, audio signals are not
output to the TV or projector.
THROUGH: The audio input to the HDMI jacks is
not output from the speaker terminals
of the SR4001/SR5001. Audio data is
output directly to the TV or projector.
This setting is used to listen to audio
on a multi channel TV, etc.
DC TRIGGER:
Select “DC TRIG SETUP” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
3-2 DC TIRGGER SETUP
DC TRIG
DISABLE
:
:
:
:
:
MAIN RETURN
CD
:
TAPE :
CD-R :
AUX2 :
TUNER:
7.1CH:
EXIT
You can select MAIN ROOM, MULTI ROOM,
REMOTE or DISABLE by pressing 1 or 2 cursor
buttons.
28
PARAMETER
4 SURROUND
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
TV
DVD
VCR1
DSS
AUX1
: 0
: 0
1.
PANORAMAA
: OFF
DIMENSION
:
3
CENTER WIDTH :
3
4 SURROUND
SURR.MODE :AUTO
HT-EQ
:OFF
LFE LEVEL :
MAIN
EXIT
Select “PL II MUSIC” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the ENTER
button.
MAIN
EXIT
SURR.MODE:
Select the desired surround mode with the 1 or 2
cursor buttons.
HT-EQ:
Select to active the HT-EQ with the 1 or 2 cursor
buttons.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back
over audio equipment in the home. This is because
film soundtracks were designed to be played back
in large movie theater environments.
Activating the HT-EQ feature when watching a film
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the
following modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
LFE LEVEL:
Select the output level of the LFE signal included in
the Dolby Digital signal or the DTS signal.
Select 0 dB, -10 dB or OFF with the 1 or 2 cursor
buttons.
PARAMETER:
Select “DEFAULT” or “CUSTOM” with the 1 or 2
cursor buttons.
If you select “CUSTOM”, you can adjust three
parameters as listed below.
PANORAMA:
Select the Panorama mode On or Off with the
1 or 2 cursor buttons.
Panorama wraps the sound of the front left and right
speakers around you, for an exciting perspective.
DIMENSION:
Set the Dimension level between +3 and –3 level
in 1 level intervals with the 1 or 2 cursor buttons.
Adjust the soundfield either towards the front or
towards the rear.
This can be useful to help achieve a more
suitable balance from all the speakers with certain
recordings.
CENTER WIDTH:
Set the Center width level between 0 and 7 in 1
level intervals with the 1 or 2 cursor buttons.
Center Width allows you to gradually spread the
center channel sound into the front left and right
speakers.
At its widest setting, all the sound from the center
is mixed into the left and right.
This control may help achieve a more spacious
sound or a better blend for the front image.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
the cursor to “MAIN” with the 3 or 4 cursor buttons
and press the ENTER button.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
1.
Select “SURROUND” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select a desired content , press the 3 or 4
cursor buttons.
EXIT
: DEFAULT
Select “CS II” in the SETUP MAIN MENU
with the 3 or 4 cursor buttons, and press the
ENTER button.
2.
To Select desired contents as below, press the
3 or 4 cursor buttons.
TRUBASS:
Set the TRUBASS level between 0 and 6 level in 1
level interval with the 1 or 2 cursor buttons.
TRUBASS produced by the speakers are an octave
below the actual physical capabilities of the speakers
adding exciting, deeper bass effects.
SRS DIALOG:
Set the SRS DIALOG level between 0 and 6 in 1
level intervals with the 1 or 2 cursor buttons.
This can be popped out of the surround audio
effects, allowing the listener to easily discern what
the actors say.
If “NONE” was selected for the Center speaker
setting, in the Speaker size set up menu, then this
setting will not appear.
After you complete this portion of the set up, move
cursor to “MAIN” with the 3 or 4 cursor buttons and
press the ENTER button.
This sub-menu is to adjust the speaker levels for 7.1channel input sources.
Here you will adjust the volume for each channel so
that they are all heard by the listener at the same
level.
8 MULTI ROOM (SR5001 only)
SR5001 has features in MULTI ROOM SYSTEM
such as source selector, sleep timer, Multi Room
Speaker output and remote control.
You can set these feature in this sub-menu.
8 MULTI ROOM
7 7.1 CH. INPUT LEVEL
VIDEO-IN
:
LAST
FRONT L
:
0 dB
CENTER
:
0 dB
FRONT R
:
0 dB
SURR.R
:
0 dB
SURR.B R
:
0 dB
SURR.B L
:
0 dB
SURR.L
:
0 dB
SUB W
:
0 dB
MAIN
EXIT
AUDIO
: DVD
SLEEP TIMER
: OFF
MULTI:OUT
: STEREO
MULTI:OFF
MSPK
:
VOL
: VARI
LEVEL
: -90dB
--- MAIN ROOM STATUS --VIDEO:DVD
AUDIO:DVD
MAIN
EXIT
1.
1.
Select “7.1CH INPUT” in the SETUP MAIN
MENU with the 3 or 4 cursor buttons, and
press the ENTER button.
2.
To select “VIDEO IN”, press 3 or 4 cursor
button.
3.
Using the 1 or 2 cursor buttons, select the
video input source which is emitted from
Monitor out in the 7.1 CH INPUT function.
The input source is switched by pressing the
1 or 2 cursor buttons as follows;
LAST ↔ TV ↔ DVD ↔ VCR1 ↔ DSS ↔
AUX1 ↔ V-OFF ↔ LAST ↔
Notes:
• When select LAST, the source is set previous source
before 7.1 CH INPUT function is activated.
• When select V-OFF, no signal is emitted from monitor
out terminal.
4.
To Select desired channel , press the 3 or 4
cursor buttons.
5.
Using the 1 or 2 cursor buttons, adjust the
volume level of each channel.
6.
After you complete this portion of the set up,
move the cursor to “MAIN” with the 3 or 4
cursor buttons and press the ENTER button.
Notes:
• These settings will be memorized to 7.1CH INPUT
source.
• This feature can be directly selected with the
CH.SEL button of the remote controller.
Select “MULTI ROOM” in the SETUP MAIN
MENU with 3 or 4 cursor button, and press the
ENTER button.
LEVEL (VOLUME LEVEL):
Adjust the Multi-speaker output level with 1 or 2
cursor button.
Note:
This setting can be changed when the Surr Back is set
“NONE” in 2-1 SPEAKER SIZE menu. When this
setting is unavailable, “✽✽✽” is displayed
ENGLISH
7 7.1 CH INPUT LEVEL
MAIN ROOM STATUS:
Selected input source in the main room will be
displayed.
Note:
If “VOLUME” is set to “FIXED”, the multi-room
output level cannot be adjusted from the second zone.
After you complete this portion of the set up, move
the cursor to “MAIN” with 3 or 4 cursor buttons and
press ENTER button.
2.
To Select desired contents, press 3 or 4 cursor
button
AUDIO:
Select the audio source of the Multi-room output
with 1 or 2 cursor buttons.
SLEEP TIMER:
SLEEP timer function is available during the
multiroom is active, set the time with 1 or 2 cursor
buttons.
MULTI OUT:
To switch MULTI and MSPK outputs to either
STEREO or MONO, press 1 or 2 cursor button.
MULTI (MULTI ROOM):
To switch on the Multi-room output ON or OFF,
press 1 or 2 cursor button.
VOL (VOLUME SETUP):
Select whether the Multi-room output level is
variable or fixed with a 1 or 2 cursor buttons.
LEVEL (VOLUME LEVEL):
Adjust the Multi-room output level with 1 or 2
cursor buttons.
MSPK B (MULTI SPEAKER B):
To switch on the Multi-speaker B output ON or
OFF, press 1 or 2 cursor buttons.
Note:
This setting can be changed when the Surr Back is set
“NONE” in 2-1 SPEAKER SIZE menu. When this
setting is unavailable, “✽✽✽” is displayed
VOL (VOLUME SETUP):
Select whether the Multi-speaker output level is
variable or fixed with a 1 or 2 cursor buttons.
Note:
This setting can be changed when the Surr Back is set
“NONE” in 2-1 SPEAKER SIZE menu. When this
setting is unavailable, “✽✽✽” is displayed
29
ENGLISH
The relation of the speakers number and
conectted speaker
SIMPLE SETUP
You can setup the speaker conditions quickly with
SIMPLE SETUP menu. In this menu, the number
of speakers and speaker delay time can be set.
These settings can be changed more detail in “2.
SPEAKER” setup menu.
Press the SIMPLE SETUP button on the unit to enter
this menu.
1. 2. 4. 3. 5.
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
STANDBY
POWER ON/STANDBY
UP
ATT
ENTER
MENU
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
CHANNEL
7.1 ch
7.0 ch
6.1 ch
6.0 ch
5.1 ch
5.0 ch
4.1 ch
4.0 ch
3.1 ch
3.0 ch
2.1 ch
2.0 ch
Front
L/R
(F)
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
LARGE
Front Surround Surround
Back L/R
L/R
Center
(SB)
(S)
(C)
SMALL SMALL
2ch
SMALL SMALL
2ch
SMALL SMALL
1ch
SMALL SMALL
1ch
SMALL SMALL
NONE
SMALL SMALL
NONE
NONE SMALL
NONE
NONE SMALL
NONE
SMALL NONE
NONE
SMALL NONE
NONE
NONE
NONE
NONE
NONE
NONE
NONE
Sub
woofer
(SW)
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
YES
NONE
R
The relation of the room size and floor space
1.
Press the SIMPLE SETUP button on the unit to
enter the “SPEAKERS” menu.
2.
Press 1 or 2 cursor button to select the speaker
number.
3.
Press the 4 cursor button to enter the “ROOM”
menu.
4.
Press 1 or 2 cursor button to select the room
size.
5.
After finishing all setup, press the 4 cursor
button to exit the SIMPLE SETUP menu.
Note:
All Simple Setup menu is reset when the speaker
setting is changed with Speaker Setup menu.
SIMPLE SETUP
: ?
EXIT
30
Floor
space
Width
(W)
Depth
(D)
SMALL
10 m2
2.7 m
3.6 m
MEDIUM
16 m2
3.6 m
4.5 m
LARGE
24 m2
4.5 m
5.4 m
Imaging Distance
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
Front (F)
Center (C)
Surround (S)
Surr. Back (SB)
Sub Woofer (SW)
6 ft. (1.8 m)
5 ft. (1.5 m)
4 ft. (1.2 m)
5 ft. (1.5 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
5 ft. (1.5 m)
7 ft. (2.1 m)
6 ft. (1.8 m)
9 ft. (2.7 m)
8 ft. (2.4 m)
7 ft. (2.1 m)
8 ft. (2.4 m)
8 ft. (2.4 m)
The relation of the room size and floor space is a
roughly standard.
1.SPEAKERS : ?
2.ROOM
SIZE
(PLAYBACK)
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
first select the input source on the SR4001/SR5001.
Example : DVD
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
DVD
VCR
BASS
TV
AUDIO
TREBLE
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
To select DVD, turn the INPUT SOURCE knob on
the front panel or simply press the DVD button on
the remote.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• As the input is changed, the SR4001/SR5001 will
automatically switch to the digital input, surround
mode, attenuation, and night mode status which
were entered during the configuration process for
that source.
• When an audio source is selected, the last video
input used remains routed to the VCR1 Output
and Monitor Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the Monitor
Output jacks and will be viewable on a TV monitor
connected to the SR4001/SR5001.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
SR4001/SR5001
VIDEO CONVERT
HDMI
AV SURROUND RECEIVER SR5001
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
When this function is activated, the video or
S-video signal can be emitted from the video, Svideo or component video output terminal.
To activate this function, select VIDEO CONVERT in
PREFERENCE menu and set ENABLE.
Notes:
• The component video signal is emitted only from
component video output terminal.
When the video equipment is connected by
component terminal, connect the monitor and
SR4001/SR5001 by the component terminal.
• This function is unavailable for the REC out
terminal.
• This function is unavailable for the still picture, fast
forward and reverse playing of the video component.
• If, while attempting to use the video convert feature,
the SR4001/SR5001 cannot synchronize with the
display device, “NO SIGNAL” appears on the
monitor, or noise is generated, this feature cannot
be used. All of these signs are caused by equipment
incompatibility; there is nothing wrong with the
SR4001/SR5001.
In such case, set VIDEO CONVERT in the
PREFERENCE menu to DISABLE. Also, connect
the video input signal to the display device via the
MONITOR OUT terminal under VIDEO and the
S-video input signal to the display device via the
MONITOR OUT terminal under S-VIDEO.
VOLUME
INPUT SELECTOR
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
PHONES
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DIGITAL
L
AUDIO
R
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
ATT
ENTER
POWER ON/STANDBY
MENU
DIGITAL
PHONES
HDMI
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
VIDEO
S-VIDEO
component
or S-VIDEO
The signal cannot be converted from the component
to the video or S-video.
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
VIDEO
S-VIDEO
component
MEMORY
UP
CLEAR
ATT
ENTER
AUTO
POWER ON/STANDBY
DISPLAY
MUTE
STANDBY
Notes of OSD menu:
• The setup menu can be displayed through all video
out (COMPONENT, S-VIDEO, VIDEO).
• The setting informations (e.g. volume setting) are
displayed through all video out when the VIDEO
CONVERT function are set ON.
Note:
No setting information is displayed when the
signal is emitted from the COMPONENT IN to
COMPONENT OUT.
• The setting informations (e.g. volume setting) are
displayed through the S-VIDEO or VIDEO out
when the VIDEO CONVERT function are set
DISABLE. When the S-VIDEO and VIDEO outputs
are used simultaneously, the setting informations are
displayed through the S-VIDEO out only.
UP
MUTE
STANDBY
AUX 1 INPUT
S-VIDEO
VIDEO
VIDEO
component
DOWN
ATT
ENTER
MENU
VOLUME
UP
MUTE
STANDBY
POWER ON/STANDBY
ENGLISH
BASIC OPERATION
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
HDMI
Notes of OSD menu:
HDMI: OSD menu is not displayed.
VIDEO/S-VIDEO/component: VIDEO CONVERT
of HDMI is not possible, thus the OSD menu is not
displayed.
Example:
Monitor is connected with the component.
SR5001 only
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
ATT
ENTER
POWER ON/STANDBY
MENU
AUX 1 INPUT
S-VIDEO
VIDEO
DIGITAL
PHONES
L
AUDIO
R
component
VIDEO
Monitor is connected with the video or S-video.
SR5001 only
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/STANDBY
HT-EQ
MENU
EXIT
BAND
T-MODE
AUX 1 INPUT
S-VIDEO
VIDEO
DIGITAL
PHONES
VIDEO
L
AUDIO
R
or S-VIDEO
Monitor is connected with the video or component.
SR4001/SR5001
AV SURROUND RECEIVER SR4001
INPUT SELECTOR
VOLUME
DOWN
7.1 CH INPUT
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
S.SPEAKER B
S-VIDEO
UP
MUTE
STANDBY
POWER ON/STANDBY
ATT
ENTER
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
VIDEO
component
31
ENGLISH
SELECTING THE SURROUND MODE
ADJUSTING THE TONE (BASS & TREBLE)
CONTROL
USING THE SLEEP TIMER
Example: AUTO SURROUND
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
PRESET
+
-
TUNING
+
LEARN
SEND
l/
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
SLEEP
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
AUDIO
SOURCE
AUTO
1
SURROUND
MODE
MULTI
SPEAKER
MULTI
PURE
DIRECT
SIMPLE
SETUP
CS
4
STANDBY
AUTO
POWER ON/STANDBY
HT-EQ
3
VIRTUAL
5
6
BASS
T.MODE
MENU
M-CH ST
PHONES
2
EX/ES
7
CL
STEREO
NIGHT
9
A/D
HT-EQ
0
+10
MEMO
DVD
VCR
DSS
TUNER
CD
CDR
MD
ADJUSTING THE MAIN VOLUME
VOLUME
CL
CH/ CAT
DOWN
SPLAY
MEMORY
BAND
A/D
HT-EQ
MEMO
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
VOLUME
UP
CLEAR
MUTE
EXIT
7.1CH IN
T-MODE
DIGITAL
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
INFO
MENU
TAPE
AUX1
AUX2
AMP
1
CS
4
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote control unit)
To adjust the bass effect, press BASS 3 or BASS 4
on the remote.
To adjust the treble effect, press TREBLE 3 or
TREBLE 4 on the remote.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
ENTER
Adjust the volume to a comfortable level using
the VOLUME control knob on the front panel or
VOLUME 3 / 4 buttons on the remote.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME 3 button on the remote,
to decrease the volume, turn counterclockwise or
press VOLUME 4 button on the remote.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 27, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
32
ON
SURROUND
dts
LIP SYNC/
INPUT
AUTO
REMOTE CONTROLLER
RC5001SR
To select the surround mode during playback, press
the SURROUND MODE button on the front panel or
the SURROUND MODE buttons on the remote.
OFF
P.DIRECT
TREBLE
TV
P.SCAN
8
7.1CH IN
SET
DISPLAY
l/
SLEEP
2
3
EX/ES
VIRTUAL
5
6
T.MODE
To program the SR4001/SR5001 for automatic
standby, press the SLEEP button on the remote.
Each press of the button will increase the time before
shut down in the following sequence.
OFF
90
10
80
20
30
40
70
60
50
The sleep time will be shown for a few seconds in the
display on the front panel, and it will count down until
the time has elapsed.
When the programmed sleep time has elapsed, the
unit will automatically turn off.
Note that the SLEEP indicator on the display will
illuminate when the Sleep function is programmed.
To cancel the Sleep function, press the SLEEP
button until the display shows “SLEEP OFF” and the
SLEEP indicator will disappear.
TEMPORARILY TURNING OFF
THE SOUND
NIGHT MODE
VOLUME
CL
CH/ CAT
DOWN
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
VOLUME
MULTI/ CAT
ISPLAY
MEMORY
EXIT
BAND
CS
M-SPKR
CLEAR
MUTE
T-MODE
DIGITAL
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
AUTO
1
UP
INFO
MENU
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CL
ENTER
CH/ CAT
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the front panel or MUTE button on the
remote.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording
or dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.
dts
2
7.1CH IN
A/D
0
+10
LIP SYNC/
INPUT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
Press the NIGHT button on the remote to turn on the
NIGHT mode.
Selecting the Night Mode ON is effective in Dolby
Digital only, and it compresses the dynamic range.
This softens loud passages such as sudden
explosions, to help prevent disturbing others late at
night.
To turn off the Night mode, press the NIGHT button
again.
The SR4001/SR5001 is equipped with many
surround modes. These are provided to reproduce
a variety of surround sound effects, according to the
content of the source to be played.
The available surround modes may be restricted
depending on the input signal and speaker setup.
AUTO
When this mode is selected, the receiver determines
whether the digital input signal is Dolby Digital, Dolby
Digital Surround EX, DTS, DTS-ES, DTS 96/24 or
PCM-audio.
Surround EX & DTS-ES will operate for multichannel
source that has a Dolby Digital Surround EX or DTSES auto trigger flag in the digital signal.
When a Dolby Digital or DTS signal is input, the
number of channels for which the corresponding
signal is encoded will be played.
Inputting a Dolby Digital two channel signal with
Dolby surround status automatically subjects that
signal to Pro Logic IIx movie processing before play.
PCM 96 kHz source material can be played in this
mode.
Notes:
• When you use this mode with certain DVD and CD
players, performing operations such as “Skip” or
“Stop” may momentarily interrupt the output.
• When the signal is not decoded, the mode is changed
to AUTO mode automatically. Refer to page 35 to
confirm the available decoding mode.
2 MODE
EX/ES
(Dolby Digital, Pro Logic IIx MOVIE, Pro Logic IIx
MUSIC, Pro Logic IIx GAME, Pro Logic)
This mode is used with source materials encoded in
Dolby Digital and Dolby Surround.
This mode provides 6.1 channel surround for DOLBY
DIGITAL EX, DTS-ES encoded source material such
as DVD.
This mode cannot be used when an analog input has
been selected.
DOLBY DIGITAL
This mode is enabled when playing source materials
encoded in Dolby Digital.
Playing multichannel encoded 6.1 or 7.1-channel
Dolby Digital sources provides five main audio
channels (left, center, right, surround left and surround
right) and Low Frequency Effect channel.
Dolby Digital EX decoding is not available in this
mode.
Dolby Digital EX
In a movie theater, film soundtracks that have been
encoded with Dolby Digital surround EX technology
are able to reproduce an extra channel which has
been added during the mixing of the program.
This channel, called Surround Back, places sounds
behind the listener in addition to the currently
available front left, front center, front right, surround
right, surround left and subwoofer channels.
This additional channel provides the opportunity
for more detailed imaging behind the listener and
brings more depth, spacious ambience and sound
localization than ever before.
Dolby Digital EX is not available in the system without
surround back speaker(s).
Dolby Pro Logic IIx brings the excitement of surround
sound to any stereo mix, while making existing
Dolby Surround mixes sound more like discrete 5.1
channels Surround sound.
Dolby Pro Logic IIx has 3 modes. Please see below.
Pro Logic IIx MOVIE
This mode provides 6.1 or 7.1 channel surround
sound from Dolby Surround encoded stereo movie
sound tracks.
Pro Logic IIx MUSIC
This mode provides 6.1 or 7.1 channel surround
sound from conventional stereo sources, analog or
digital, such as CD, Tape, FM, TV, Stereo VCR, etc.
Pro Logic IIx GAME
Game mode restores the impact low-frequency
surround effects by routing them to the system’s
subwoofer.
Pro Logic
This mode emulated original Dolby Pro Logic
decoding (3/1 surround) suit for Dolby Surround
encoded stereo movie soundtracks.
Notes:
• Pro Logic IIx mode will decode as Pro Logic II
mode when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 26)
• Pro Logic IIx mode is available for a 2ch input signal
which is encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
DTS-ES (Discrete 6.1, Matrix 6.1)
DTS-ES adds the surround center channel audio to
the DTS 5.1-channel format to improve the acoustic
positioning and makes acoustic image movement
more natural with the 6.1-channel reproduction.
This receiver incorporates a DTS-ES decoder, which
can handle DTS-ES Discrete-encoded and DTS-ES
Matrix-encoded program sources from DVD, etc..
DTS-ES Discrete 6.1 features digital discrete
recording of all channels including the surround back
channel(s) and higher quality of audio reproduction.
DTS-ES is not available in the system without a
surround back speaker.
dts MODE
(dts, Neo:6 Cinema, Neo:6 Music)
This mode is for DTS encoded source materials such
as LASER DISC, CD, and DVD. Neo:6 is for some 2
channel sources.
dts : This mode is enabled when playing source
materials encoded in dts multichannel.
Playing multichannel encoded 5.1-channel dts
sources provides five main audio channels (left,
center, right, surround left and surround right) and
Low Frequency Effect channel.
dts-ES decoding is not available in this mode.
The DTS mode cannot be used when an analog
input has been selected.
Neo:6 Cinema, Neo:6 Music
This mode decodes 2-channel signals into 6channel signals using high-accuracy digital matrix
technology.
The DTS NEO:6 decoder has near-discrete properties
in the frequency characteristics of the channels as
well as in channel separation.
According to the signals to be played back, DTS
NEO:6 uses either the NEO:6 CINEMA mode
optimized for movie playback or the NEO:6 MUSIC
mode optimized for music playback.
ENGLISH
SURROUND MODE
Notes:
• Neo:6 mode is available to 2ch input signals which
are encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
MULTI CH. ST
This mode is used to create a wider, deeper and more
natural soundstage from two channel source material.
This is done by feeding the left channel signal to
both left front and left surround speaker and the right
channel signal to both right front and right surround
speaker. Additionally, the center channel reproduces
a mix of the right and left channel.
CIRCLE SURROUND II
(CSII-CINEMA, CSII-MUSIC, CSII-MONO)
Circle Surround is designed to enable multichannel
surround sound playback of non-encoded and
multichannel encoded material.
Backward compatibility provides listeners with up to
6.1 channels of surround performance from entire
collection of music and film, including broadcast,
videotape and stereo recorded music.
Depending on source material, you can select CSIICinema mode, CSII-Music mode or CSII-Mono
mode.
CSII Cinema mode
This mode is suited for playing back Circle Surroundencoded and non-encoded film and television
soundtracks. Cinema Mode enables 6.1-channel
surround playback of 2-channel sources such as
Video Cassettes, TV broadcasts, streaming media
and DVDs.
CSII Music mode
This mode is suited for playing back Circle
Surround-encoded and non-encoded music. Music
Mode decodes, music DVDs, radio and TV music
broadcasts and CDs into enveloping 6.1-channel
surround.
33
ENGLISH
CSII-Mono mode
This mode plays back monaural recordings from
any source, including CDs, DVDs and TV and radio
broadcasts in compelling 6.1-channel surround.
Notes:
• CS II mode is available for 2ch input signals which
are encoded in Dolby Digital or PCM format.
• PCM-audio signals can be subjected to Pro Logic
processing when the sampling frequency is 32 kHz,
44.1 kHz or 48 kHz.
VIRTUAL
This mode creates a virtualized surround sound
experience from a two-speaker (front L and R)
playback system playing any multichannel audio
source (such as found on DVDs and digital
broadcasts), including Dolby Digital, Dolby Pro Logic
or DTS.
STEREO
This mode bypasses all surround processing.
In stereo program sources, the left and right channels
play normally when PCM-audio or analog stereo is
input.
With Dolby Digital and DTS sources, the 5.1
multichannels are converted to two channel stereo.
96 kHz PCM source material can be played back in
stereo mode.
SOURCE DIRECT
In the Source Direct mode, the tone control circuit
and bass management configuration are bypassed
for full-range frequency response and the purist
audio reproduction.
Notes:
• Speaker size is set to Front L/R = LARGE, Center =
LARGE, Surround L/R = LARGE and Subwoofer
= YES automatically. Tone controls, equalizer and
additional processing are deactivated.
• When you use this mode with certain DVD and CD
players, performing operations such as skip or stop
may momentarily interrupt the output.
PURE DIRECT
The Pure Direct mode further reduces sources of
noise in addition to effect of the Source Direct mode,
by blocking output from the video jacks (VIDEO,
S-VIDEO, COMPONENT VIDEO and HDMI) and
turning the FL display off.
34
CAUTION
NOTE for DTS signal
* Connected DVD-player, laser-disc player or
CD-player needs to support DTS-digital output.
You may not be able to play some DTS source
signals from certain CD players and LD players
even if you connect the player to the SR4001/
SR5001 digitally. This is because the digital signal
has been processed (such as the output level,
sampling frequency, or frequency response) and
the SR4001/SR5001 cannot recognize the signal
as DTS data.
* Depending on the player used, DTS play may
produce a short noise. This is not a malfunction.
* While signals from DTS-laser disc or CD are
playing in another Surround mode, you cannot
switch to digital input or from digital input to analog
input by INPUT SETUP in SETUP MAIN MENU or
the A/D button.
* The outputs for the VCR 1 OUT, DSS/VCR 2
OUT, TAPE OUT, and CD-R OUT output analog
audio signals. Do not record from CDs or LDs that
support DTS using these outputs. If you do, the
DTS-encoded signal will be recorded as noise.
NOTE for Dolby Digital Surround EX signal
* When playing Dolby Digital Surround EX-encoded
software in 6.1 channels, it is required to set the
EX/ES mode.
* Note that some of Dolby Digital Surround
EX-encoded software does not contain the
identification signal. In this case, set the EX/ES
mode manually.
NOTE for 96kHz PCM audio
* AUTO, PURE-DIRECT, and STEREO modes
can be used when playing PCM signals with a
sampling frequency of 96 kHz (such as from DVDVideo discs that contain 24 bit, 96 kHz audio). If
such signals are input during playback in one of
the other surround modes, output from SR4001/
SR5001 will be muted.
* Certain DVD player models inhibit digital output.
For details, refer to the player’s operation manual.
* Some DVD formatted discs feature copy protection.
When using such disc, 96 kHz PCM signal is not
output from the DVD player. For details, refer to
the player’s operation manual.
NOTE for HDCD signal
* HDCD is effective only at the time of digital input.
* AUTO, PURE DIRECT, and STEREO modes can
be used when playing HDCD signals (such as
from CD discs that contain HDCD).
* You may not be able to play some HDCD source
signals from certain CD players if you connect
the player to the SR4001/SR5001 digitally. This
is because the digital signal has been processed
(such as the output level, sampling frequency, or
frequency response) and the SR4001/SR5001
cannot recognize the signal as HDCD data.
Surround Mode
Input Signal
Decoding
AUTO
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D(2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM(Audio)
PCM 96kHz
HDCD
Analog
Dolby D Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby D Surr. EX
Dolby D (5.1ch)
DTS-ES
DTS(5.1ch)
Dolby D Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
PCM (Audio)
Analog
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
PCM (Audio)
Analog
Dolby D (2ch)
Dolby D (2ch Surr)
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS 96/24
DTS (5.1ch)
PCM (Audio)
PCM 96kHz
HDCD
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS (5.1ch)
PCM (Audio)
Analog
Dolby Surr. EX
Dolby D (5.1ch)
Dolby D (2ch)
Dolby D (2ch Surr)
DTS-ES
DTS (5.1ch)
PCM (Audio)
Analog
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital 5.1
Dolby Digital 2.0
Pro Logic IIx movie
DTS-ES
DTS 96/24
DTS 5.1
PCM (Stereo)
PCM (96kHz Stereo)
PCM (Stereo)
Stereo
Dolby Digital EX
Dolby Digital EX
DTS-ES
DTS-ES
Dolby Digital 5.1
Dolby Digital 5.1
Pro Logic IIx
Pro Logic IIx
Pro Logic IIx
Pro Logic IIx
DTS 5.1
DTS 96/24
DTS 5.1
Neo:6
Neo:6
Neo:6
Neo:6
CS II
CS II
CS II
CS II
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
Stereo
PCM (Stereo)
Stereo
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Virtual
Dolby Digital EX
Dolby Digital 5.1
Multi Channel Stereo
Multi Channel Stereo
DTS-ES
DTS 5.1
Multi Channel Stereo
Multi Channel Stereo
PURE DIRECT
EX/ES
DOLBY
(PL IIx movie)
(PL IIx music)
(PL IIx game)
(Pro Logic)
DTS
(Neo:6 Cinema)
(Neo:6 Music)
CS II Cinema
CS II Music
CS II Mono
STEREO
Notes:
• Dolby Digital (2 ch: Lt/Rt): signal with Dolby
Surround flag Speakers are full set.
• No sound outputs from the surround speaker, center
speaker and subwoofer if the DVD disc has no
surround data.
Abbreviations
L/R :
C:
SL/SR :
SBL/SBR :
SubW :
Front speakers
Center speaker
Surround speakers
Surround Back speakers
Sub woofer speaker
Virtual
Multi Ch.
Stereo
L/R
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Output Channel
SL SBL
SubW Signal format indicators
C
SR SBR
O O O O 2 DIGITAL
O O
O 2 DIGITAL
- 2 DIGITAL
O O O
- 2 DIGITAL , 2 SURROUND
O O O O dts, ES
O O
O dts 96/24
O O
O dts
- PCM
- PCM
- PCM HDCD
- ANALOG
O O O O 2 DIGITAL
O O
O 2 DIGITAL
- 2 DIGITAL
O O O
- 2 DIGITAL , 2 SURROUND
O O O O dts, ES
O O
O dts 96/24
O O
O dts
- PCM
- PCM
- PCM HDCD
- ANALOG
O O O O 2 DIGITAL
O O O O 2 DIGITAL
O O O O dts , ES
O O O O dts
O O O O 2 DIGITAL
O O O O 2 DIGITAL
O O O
- 2 DIGITAL
O O O
- 2 DIGITAL , 2 SURROUND
O O O
- PCM
O O O
- ANALOG
O O
O dts, ES
O O
O dts 96/24
O O
O dts
O O O
- PCM
O O O
- ANALOG
O O O
- 2 DIGITAL
O O O
- 2 DIGITAL , 2 SURROUND
O O O O PCM
O O O O ANALOG
O O O O 2 DIGITAL
O O O O 2 DIGITAL , 2 SURROUND
O 2 DIGITAL
O 2 DIGITAL
- 2 DIGITAL
- 2DIGITAL , 2 SURROUND
O dts, ES
O dts 96/24
O dts
- PCM
- PCM
- PCM HDCD
- ANALOG
- 2 DIGITAL
- 2 DIGITAL
- 2 DIGITAL
- 2 DIGITAL , 2 SURROUND
- dts, ES
- dts
- PCM
- ANALOG
O O O O 2 DIGITAL
O O
O 2 DIGITAL
O O O
- 2 DIGITAL
O O O
- 2 DIGITAL , 2 SURROUND
O O O O dts, ES
O O
O dts
O O O
- PCM
O O O
- ANALOG
Front information display
Channel status
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R, S
L, R
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, C, R, SL, SR, LFE
L, R
L, R
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, R, S
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
L, C, R, SL, SR, S, LFE
L, C, R, SL, SR, LFE
L, R
-
ENGLISH
The relation between the selected surround
mode and the input signal
The surround mode is selected with the surround
mode selector on SR4001/SR5001 or the remote
control unit. However, the sound you hear is subject
to the relationship between the selected surround
mode and input signal. That relationship is as
follows;
35
ENGLISH
OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
REC
TV AUTO ON/OFF FUNCTION
This function allows the component connected to the
TV-VIDEO in jack to control the power (ON/OFF) to
the SR4001/SR5001.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED. (Refer
page 27 : System Setup)
2.
Connect your TV TUNER (etc) to the TVVIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
SR4001/SR5001.
4.
Turn ON the TV TUNER and tune in a receivable
station.
5.
When the station is received, the SR4001/
SR5001 turns ON and TV is selected
automatically.
-
T.DISP
PRESET
+
PTY
-
+
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
AUDIO
TREBLE
HEAD PHONE
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on
the remote.
“ATT” indicator will be illuminated when this function
is activated. The signal-input level is reduced by
about half. Attenuation will not work with the output
signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT
and DSS/VCR2-OUT.
This function is memorized for each individual input
source.
1.
2.
In the above situation, turn the TV TUNER OFF
or select a channel that does not contain any
broadcast.
The power to the SR4001/SR5001 switches to
STANDBY after approx. 5 minutes.
This jack may be used to listen to the SR4001/
SR5001’s output through a pair of headphones.
Be certain that the headphones have a standard
1/4” stereo phono plug. (Note that the speakers will
automatically be turned off when the headphone jack
is in use.)
AV SURROUND RECEIVER SR5001
Notes:
• AUTO POWER OFF is canceled if the SR4001/
SR5001 is set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support “TV AUTO
ON/OFF” function.
INPUT SELECTOR
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
STANDBY
POWER ON/STANDBY
MENU
PHONES
Note:
The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
When no video signal is connected to the SR4001/
SR5001 or a DVD, etc., is connected directly to your
TV, the unnecessary video circuit can be turned off
by selecting the “VIDEO OFF” setting.
To select video off, press the AMP button and press
the V-OFF button.
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
DOLBY HP MODE : ON
SURROUND
: OFF
L LEVEL
R LEVEL
:
:
DSS
R5001
REMOTE CONTROLLER
RC5001SR
0 dB
0 dB
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
ENTER
MENU
-
PRESET
DISC+
+
-
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
DVD
VCR
CH-SEL
BASS
TV
+
AUDIO
TREBLE
DSS
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
BYPASS → ON → BYPASS
BYPASS: Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
ON: Dolby headphone mode active.
LISTENING THROUGH HEADPHONES
AUTO POWER OFF
VIDEO ON/OFF
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
F.DIRECT
TUNING
BASS
DOLBY HEADPHONE MODE
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and “✽✽✽” is
displayed as the mode indication.
DISPLAY MODE
ER SR5001
LEARN
SOURCE
L/R LEVEL can be set in the ±10 dB range.
Notes:
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
• TONE cannot be set when mode is ON.
• The Dolby Headphone function will not work when
32 or 96 kHz PCM digital signals are input.
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
AUTO
ENTER
The surround mode can be selected when mode is
ON.
SEND
SET
MENU
1
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
T.MODE
P.SCAN
You can select the display mode for the front display
of the SR4001/SR5001.
To select this mode, press the DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display in display off condition
36
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
CL
CH/ CAT
P.SCAN
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
1.
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR4001/SR5001 is
sent to the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for TAPE OUT,
CD-R/MD OUT, VCR1 OUT in the record mode.
To record the input source signal you are currently
watching or listening to
1.
VOLUME
-
PRESET
+
-
TUNING
+
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
DISC+
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the AMP button and press the A/D (0) button.
When this button is pressed, the input mode is
switched in the following sequence.
→ HDMI Auto → HDMI → Digital Auto → Digital →
Analog → HDMI Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 26)
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
1.
STANDBY
POWER ON/STANDBY
AUDIO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
MENU
PHONES
Switch the video output source to VCR1 by
simply pressing the input selector buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the input selector buttons on the
remote.
3.
Now “CD” has been selected as the audio input
source and “VCR1” as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
7.1 CH INPUT
The SR4001/SR5001 is equipped for future
expansion through the use of Multi channel Super
Audio CD multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the Monitor Outputs.
This permits simultaneous viewing with video
sources.
2. 1.
REMOTE CONTROLLER
RC5001SR
M-CH ST
Select the input source to record by turning the
INPUT SOURCE knob on the front panel or
simply press the input selector buttons on the
remote.
HT-EQ
MULTI
SPEAKER
MULTI
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
STEREO
7
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
1.
ENGLISH
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
2.
4.
9
A/D
0
+10
CL
CH/ CAT
NIGHT
8
7.1CH IN
P.SCAN
HT-EQ
MEMO
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
STANDBY
POWER ON/STANDBY
INFO
PHONES
MENU
DOWN
The input source is now selected and you may
watch or listen to it as desired.
ENTER
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
3.
The currently selected input source signal
is output to the TAPE OUT, CD-R/MD OUT,
VCR1 OUT outputs for recording.
Start recording to the recording component as
desired.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS/VCR2
to video cassette recorder connected to the VCR1
OUT jack.
DISC+
1.
2.
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
BASS
AUDIO
T.TONE
/SET UP
CLEAR
4.
ENTER
AUTO
2.
MEMORY
PHONES
EXIT
MUTE
STANDBY
POWER ON/STANDBY
DISPLAY
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
REC
-
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
+
VOLUME
DISC+
Press the HT-EQ button on the front panel to turn on
the HT-EQ mode.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back over
audio equipment in the home. This is because film
soundtracks were designed to be played back in
large movie theater environments.
Activating the HT-EQ feature when watching a film
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the following
modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
ANGLE
SUB TITLE
V-OFF
ATT.
CH-SEL
DOWN
MEMORY
UP
1.
CLEAR
MUTE
BAND
AUDIO
T-MODE
DIGITAL
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
BASS
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
R
REMOTE CONTROLLER
RC5001SR
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
37
ENGLISH
1.
Select a desired Video source to decide the
routed video signal to the Monitor Outputs.
2.
Press the 7.1 CH INPUT button on the front
panel or press 7.1 CH IN on the remote to
switch the 7.1 channel input.
3.
If it is necessary to adjust the output level of
each channel, press the CH.SEL button on the
remote.
AUX2 INPUT
If you don’t need to connect 7.1 Ch. input terminals
with multi channel decoder,
L(front left) and R (front right) inputs terminals are
available as AUX2 input.
In this case, You can connect additional audio source
to AUX2 as other audio input terminals.
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
Adjust the speaker output levels so that you can
hear the same sound level from each speaker
at the listening position. For the front left, front
right, center, surround left, surround right and
surround back speakers, the output levels can
be adjusted between –10 to +10 dB.
2.
(TUNER)
Adjust the main volume with the MAIN VOLUME
knob or the VOLUME buttons on the remote.
To cancel the 7.1 CH. INPUT setting, press the 7.1
CH INPUT button on the front panel or press 7.1 CH
IN on the remote.
Notes:
• When the 7.1 CH. Input is in use, you may not select
a surround mode, as the external decoder determines
processing.
• In addition, there is no signal at the record outputs
when the 7.1 CH. Input is in use.
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMP
SETU
STANDBY
POWER ON/STANDBY
MEN
PHONES
1.
VCR
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
Frequency scan step for AM is selectable.
Default setup is 9 kHz step, if your country’s standard
is 10 kHz step, Press BAND button on the remote
more than 6 seconds. Scan step will change.
Note:
Preset memory for the tuner will clear by changing
this setup.
2.
LIP.SYNC (SR5001 only)
Depending on the image device (TV, monitor,
projector, etc.) connected to the SR5001, a time lag
can occur between image signal processing and
audio signal processing. Though minor, this time
lag can interfere with movie and music enjoyment.
The LIP.SYNC feature delays the audio signal with
respect to the image signal output from the SR5001
to correct the time lag between the sound and image.
It can be operated with the “LIP.SYNC” and 1 and
2 cursor buttons of the remote controller. Set the
remote controller to the AMP mode before operating
the LIP.SYNC feature. The initial setting is OFF (0
ms).The time lag can be adjusted in 10 ms steps up
to 200 ms.
Watch the picture on the image device (i.e., TV,
monitor, projector, etc.) as you adjust the time lag.
TREBLE
DVD
DOWN
REC
ND
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
T.DISP
1.
TV
MENU
DIGITAL
2.
-
PRESET
DISC+
1.
VCR
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
ND
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
T.DISP
PTY
ANGLE
SUB TITLE
V-OFF
ATT.
MENU
DIGITAL
2.
-
PRESET
+
-
TUNING
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
+
AUDIO
TREBLE
To select tuner and desired band (FM or AM),
press the BAND button on the front panel
2.
Press the 3 or 4 cursor buttons on the front
panel to select the desired station.
(Using the remote control unit)
1.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
2.
Press the 5 or 6 on the remote to tune in the
desired station.
F.DIRECT
M
ENTER
HT-EQ
F.DIRECT
TUNING
1.
DOWN
REC
-
(Using the SR5001)
DSS
TUNER
+
BASS
TREBLE
DVD
PTY
M
ENTER
HT-EQ
AUTO TUNING
Note:
The LIP.SYSNC feature turns OFF (0 ms) in the
PURE DIRECT mode. When the PURE DIRECT
mode is deactivated, the set value of the LIP.SYSNC
feature is automatically restored.
+
AUDIO
DIRECT FREQUENCY CALL
(Using the SR5001)
SLEEP
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
1.
2.
3.
SLEEP
To select tuner and desired band (FM or AM),
press the BAND button on the front panel.
Press the 3 or 4 cursor buttons on the front
panel for more than 1 second to start the auto
tuning function.
1
3.
(Using the remote control unit)
CS
4
M-CH ST
7
CL
CH/ CAT
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
AUTO
Automatic searching begins then stops when a
station is tuned in.
2
3
EX/ES
VIRTUAL
5
6
STEREO
NIGHT
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
M-SPKR
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
T.MODE
P.SCAN
T.MODE
7
8
9
7.1CH IN
A/D
HT-EQ
T.DISP
PTY
F.DIRECT
P.SCAN
/SET UP
HT-EQ
EXIT
MEMO
VOLUME
MULTI/ CAT
1
2.
REC
-
PRESET
+
-
TUNING
+
1.
1.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
To select tuner and desired band (FM or AM),
press the BAND button on the remote.
2.
2.
Press the 5 or 6 for more than 1 second on
the remote.
Press the F.DIRECT on the remote, display will
show “FREQ - - - -”.
3.
3.
Automatic searching begins then stops when a
station is tuned in.
Input your desired station’s frequency with the
numeric buttons on the remote.
4.
The desired station will automatically be tuned.
If tuning does not stop at the desired station, use to
the “Manual tuning” operation.
38
BASS
TV
TUNER
LISTENING TO THE TUNER
BASS
4.
1.
CH-SEL
MULTI
The subwoofer can be adjusted between –15
and +10 dB.
These adjustments result will be stored to 7.1
CH. INPUT memory.
MANUAL TUNING
BASIC OPERATION
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
l/
VOLUME
SLEEP
AUTO
DOWN
UP
1
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
CS
DISPLAY
MEMORY
CLEAR
MUTE
ATT
ENTER
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
dts
7
CL
CH/ CAT
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
LIP SYNC/
INPUT
T.MODE
MANUAL PRESET MEMORY
PRESET MEMORY
With this unit you can preset up to 50 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
3.
RECALLING A PRESET STATION
2. 4.
SLEEP
AUTO
1
MEMO
VOLUME
When in the auto stereo mode, AUTO indicator will
be illuminated on the display.
The “ST” indicator is illuminated when a stereo
broadcast is tuned in.
At open frequencies, the noise is muted and the
“TUNED” and “ST” indicators are not illuminated.
If the signal is weak, it may be difficult to tune into
the station in stereo. In such a case, press the
T-MODE button on the front panel or remote.
“AUTO” indicator is not illuminated, if FM stereo
broadcasts are received in monaural and the “ST”
indicator is not illuminated.
To return to auto stereo mode, press the T-MODE
button or press T-MODE button on the remote again.
AUTO indicator is illuminated on the display.
3.
AUTO PRESET MEMORY
SURROUND
MODE
PURE
DIRECT
VOLUME
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
AUTO
HT-EQ
POWER ON/STANDBY
MENU
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
DIGITAL
ATT
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
To select FM, press the BAND button on the
front panel.
2.
While pressing the MEMO button, press the
cursor button.
“AUTO PRESET” will appear on the display,
and scanning starts from the lowest frequency.
VIRTUAL
5
6
STEREO
NIGHT
SLEEP
1.
7
8
9
DISPLAY
MEMORY
1.
EXIT
BAND
T
2.
CH/ CAT
A/D
HT-EQ
0
+10
MEMO
CS
2
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
0
+10
SPKR A/B
MUTE
T.DISP
PTY
CL
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CH/ CAT
CLEAR
P.DIRECT
dts
1
P.SCAN
7.1CH IN
DISPLAY
AUTO
T.MODE
SURROUND
LIP SYNC/
INPUT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
ENTER
AUTO
HT-EQ
MENU
EXIT
BAND
REC
T-MODE
1.
MENU
2.
Press the MEMO button on the front panel.
“– –“ (preset number) starts blinking on the
display.
3.
Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMO button again to enter. The
display stops blinking.
-
PRESET
DISC+
+
ANGLE
-
F.DIRECT
TUNING
SUB TITLE
+
AUDIO
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
During this time, the following operations are
possible.
2.
Press the MEMO button on the remote. “– –“
(preset number) starts blinking on the display.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
Operation stops automatically when all 50
preset memory positions are filled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
(Using the SR5001)
1.
3.
1.
Press the S or T buttons to select the
desired preset station, or input your desired
preset channel with the numeric buttons on
the remote.
PRESET SCAN
CS
EX/ES
3.
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
CH/ CAT
REC
T.MODE
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
CL
-
Enter the desired preset number by pressing
the numeric buttons.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel
(Using the remote control unit)
The station is now stored in the specified preset
memory location.
(Using the remote control unit)
1.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
EX/ES
4
Each time the tuner finds a station, scanning
will pause and the station will be played for five
seconds.
The band can be changed by the BAND button.
4.
3
Tune into the radio station you desire (Refer to
the “MANUAL TUNING” or “AUTO TUNING”
section).
R
1.
3.
2
1.
ENTER
PHONES
MENU
CS
INFO
UP
MUTE
STANDBY
dts
LIP SYNC/
INPUT
(Using the SR5001)
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
SURROUND
M-CH ST
CL
SIMPLE
SETUP
ENTER
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 4. 2. 5. 1. 3.
P.DIRECT
ECEIVER SR5001
P.SCAN
HT-EQ
DISPLAY
ENGLISH
(FM) TUNING MODE (AUTO STEREO OR MONO)
1.
3.
VOLUME
T.DISP
PRESET
+
PTY
-
F.DIRECT
TUNING
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
+
AUDIO
3.
SS
(Using the remote control unit)
1.
Press the P.SCAN on the remote.
“PRESET SCAN” appears on the display and
then the preset station with the lowest preset
number is recalled first.
2.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
3.
You can fast forward the preset stations by
pressing the T continuously.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P.SCAN on the remote.
39
ENGLISH
CLEARING STORED PRESET STATIONS
SORTING PRESET STATIONS
You can remove preset stations from the memory
using the following procedure.
2. 3.
AUTO
1
CS
VOLUME
2.
DOWN
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
VIRTUAL
5
6
STEREO
NIGHT
7
3.
INFO
1.
EX/ES
4
CH/ CAT
DISPLAY
3
M-CH ST
CL
ENTER
dts
2
8
9
7.1CH IN
A/D
0
+10
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
LIP SYNC/
INPUT
T.MODE
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
POWER ON/STANDBY
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
P.SCAN
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
4.
R
5. 2. 5. 6.
To move back and forth between the characters,
press the 1 / 2 cursor buttons or press S or
T buttons on the remote.
AV SURROUND RECEIVER SR5001
MEMO
INPUT SELECTOR
VOLUME
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
MENU
Recall the preset number to be cleared with
the method described in “Recalling” a preset
station.
Press the MEMO button on the front panel or
press the MEMO button on the remote.
3.
The stored preset number blinks in the display
for 5 seconds. While blinking, press the CLEAR
button on the front panel or the remote.
If you have stations memorized, and there is a gap in
the sequential order:
I.e. the stations are stored as follows
1) 87.1 MHz
2) 93.1 MHz
3) 94.7 MHz
10) 105.9 MHz
(notice there is no stations programmed for pre sets
for 4-9), you can have pre set 10 become pre set 5:
To sort the numbers, press and hold the MEMO and
the 4 cursor buttons.
“PRESET SORT” will appear on the display and
sorting will be done.
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
PHONES
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
6.
7
2. 5. 6.
8
CH/ CAT
A/D
0
+10
SPKR A/B
MUTE
HT-EQ
MULTI/ CAT
M-SPKR
MEMO
VOLUME
MENU
ENTER
T.TONE
/SET UP
“xx CLEAR” appears on the display to indicate
that the specified preset number has been
cleared.
EXIT
REC
5.
4.
-
T.DISP
PRESET
DISC+
+
PTY
-
TUNING
SUB TITLE
V-OFF
ATT.
DVD
VCR
BASS
TV
F.DIRECT
ANGLE
CH-SEL
To save the name, press the MEMO button
on the front panel or remote for more than 2
seconds.
9
7.1CH IN
CL
INFO
Note:
To clear all stored preset stations, press and hold the
CLEAR and the ENTER buttons for two seconds.
+
AUDIO
TREBLE
DSS
1.
Recall the preset number to be inputted name
with the method described in “Recalling” a
preset station.
2.
Press the MEMO button on the front panel or
press the MEMO button on the remote for more
than 3 seconds.
3.
The left most column of the station name
indicator flashes, indicating the character entry
ready status.
4.
When you press the 3 or 4 cursor buttons on
the front panel or the 5 / 6 buttons on the
remote, alphabetic and numeric characters will
be displayed in the following order:
A → B → C ... Z → 1 → 2 → 3 ..... 0 → – → +
→ / → (Blank) → A
UP →
← DOWN
40
Note:
Unused columns should be filled by entering blanks.
ENTER
AUTO
POWER ON/OFF
DISPLAY
After selecting the first character to be entered,
press the MEMO or ENTER buttons, press the
MEMO button on the remote.
The entry in this column is fixed and the next
column starts to flash. Fill the next column the
same way.
ATT
ENTER
PHONES
5.
This function allows the name of each preset channel
to be entered using alphanumeric characters.
Before name inputting, you need to store preset
stations with the preset memory operation.
HT-EQ
2.
4.
NAME INPUT OF THE PRESET STATION.
Ten keypad
1
2
3
4
5
6
7
8
9
0
Press, press again, press again, etc.
A→B→C→1→A
D→E→F→2→D
G→H→I→3→G
J→K→L→4→J
M→N→O→5→M
P→Q→R→6→P
S→T→U→7→S
V→W→X→8→V
Y → Z → space → 9 → Y
–→+→/→0
SELECTING AN INPUT SOURCE
ENTER
T.TONE
/SET UP
Before you can listen to XM Satellite Radio, you must
first select the input source on the SR5001.
SOURCE
1.
SET
OFF
DISPLAY
REC
T.DISP
PTY
SURROUND
dts
LIP SYNC/
INPUT
PRESET
DISC+
AUTO
1
+
3
BAND
VIRTUAL
T.MODE
5
6
M-CH ST
STEREO
NIGHT
CS
7
SURROUND
MODE
MULTI
SPEAKER
MULTI
8
-
TUNING
+
2.
AUTO
T.TONE
/SET UP
BASS
V-OFF
A/D
HT-EQ
0
+10
MEMO
DISC+
ANGLE
SUB TITLE
AUDIO
V-OFF
ATT.
T.TONE
/SET UP
REC
HT-EQ
PTY
EXIT
F.DIRECT
PRESET
+
-
TUNING
DISC+
TREBLE
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
ANGLE
SUB TITLE
V-OFF
ATT.
AUDIO
DISPLAY
CH-SEL
ENTER
MENU
BASS
REC
+
ATT.
MULTI
1.
T.DISP
AUDIO
POWER ON/OFF
7.1CH IN
ENTER
EXIT
INPUT SELECTOR
STANDBY
9
You can display XM information (such as artist name/
song title, category or signal status) for the channel
currently selected in the front panel display.
AV SURROUND RECEIVER SR5001
-
STANDBY
POWER ON/OFF
SUB TITLE
1.
P.SCAN
CL
PURE
DIRECT
ANGLE
CH-SEL
2
EX/ES
4
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
3.
F.DIRECT
MENU
INFO
SWITCHING XM INFORMATION IN THE FRONT
PANEL DISPLAY
ENTER
-
ON
P.DIRECT
Select channel 0 (XM000) with the 3 or 4
cursor buttons of the SR5001 or the Q or
R buttons of the remote control unit.
EXIT
l/
SLEEP
3.
ENGLISH
CHECKING THE XM SIGNAL STRENGTH
AND RADIO ID
LISTENING TO XM SATELLITE RADIO
3.
-
Press the T.DISP button 3 times to displayed
Signal Status.
PRESET
+
PTY
-
F.DIRECT
TUNING
+
1.
TREBLE
EXIT
PHONES
T.DISP
DISC+
TV
DVD
VCR
ANGLE
SUB TITLE
V-OFF
ATT.
AUDIO
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
CH-SEL
BASS
TREBLE
REMOTE CONTROLLER
PHONES
CH-SEL
BASS
S I G N A L :
TREBLE
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
1.
REMOTE CONTROLLER
RC5001SR
• The display changes as shown below according to
the receiving condition.
1.
• The Radio ID is displayed.
X M O O O R A D I O
I D
Press the T.DISP button to displayed
INFORMATION.
Channel number/name
Artist name/Song title
SIGNAL: ■■■■■■
SIGNAL: STRONG
(Signal strength is good)
2.
SIGNAL: ■■■■
SIGNAL: MARGINAL
(Signal strength is Marginal)
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
ATT
ENTER
POWER ON/OFF
MENU
PHONES
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
SIGNAL: ■■
SIGNAL: WEAK
(Signal strength is poor)
R
XM NO SIGNAL
SIGNAL: NON
(Loss of the signal)
(Using the SR5001)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
Press the BAND button to select XM band.
(Using the remote control unit)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
Press the BAND button to select XM band.
2.
Adjust the antenna location until signal strength
is good.
Channel category
Notes:
• If “ANTENNA” appears in the front panel display,
the XM Connect-and-Play antenna or Passport
system may not be connected to the XM terminal on
the rear panel of this unit properly.
• The ATT function is also effective when XM is
selected.
Signal Status
When the Channel number/name is displayed:
X M O 4 0 : D e e p T r c
4 0 : D e e p T r a c k s
(If text is more than 13 characters long, the text is
scrolled.)
Note:
The front Panel display can indicate up to 13 alphanumeric
characters at once. If the information contains more then
13 characters, the information scrolls from right to left.
41
ENGLISH
When the channel Artist name/Song title is
displayed:
2.
When you press the INFO button, the following
information will be displayed.
N A M E / T I T L E
VIDEO
AUDIO
P i n k
F l o i d
F l o i d
/
/
Note:
The front Panel display can indicate up to 13
alphanumeric characters at once. If the information
contains more then 13 characters, the information
scrolls from right to left.
When this display appears, press the INFO
button again. XM information like the following
will appear.
MAIN
This XM information can also be displayed on a TV
monitor connected to the SR5001.
VOLUME
MUTE
M-SPKR
MENU
2.
ENTER
T.TONE
/SET UP
EXIT
REC
T.DISP
PTY
F.DIRECT
DISC+
ANGLE
SUB TITLE
AUDIO
CH-SEL
V-OFF
ATT.
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
REMOTE CONTROLLER
RC5001SR
1.
42
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
AUTO
1
R5001
2
3
BAND
EX/ES
VIRTUAL
T.MODE
4
5
6
M-CH ST
STEREO
NIGHT
7
8
9
REC
T.DISP
PTY
CS
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
-
PRESET
4.
DSS
1.
Press the AMP button on the remote control
unit.
TUNING
DISC+
ANGLE
SUB TITLE
+
CH-SEL
V-OFF
ATT.
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
MENU
EXIT
BAND
T-MODE
AUDIO
2.
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1.
2.
F.DIRECT
+
-
TUNING
ANGLE
SUB TITLE
V-OFF
ATT.
+
AUDIO
2.
TREBLE
DVD
VCR
DSS
TUNER
CD
CDR
MD
AUX1
AUX2
AMP
(Using the SR5001)
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
3.
Press the BAND button to select XM band.
Press the 3 or 4 cursor button on the front
panel to select the desired station.
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
3.
Press the BAND button to select XM band.
Press and hold the 5 or 6 button.
1.
Turn the INPUT SELECTOR knob to select
“TUNER”.
2.
3.
Press the BAND button to select XM band.
1.
REMOTE CONTROLLER
RC5001SR
Note:
If the information contains a character that cannot be
recognized by that unit, the character will be displayed
with “ ”(space).
-
001
P.SCAN
TV
TAPE
Press the INFO button again. The information
display will go out.
+
F.DIRECT
(Using the SR5001)
CH-SEL
EXIT
PRESET
PTY
ENTER
MENU
:040
:DeepTracks
:Pink Floid
:Money
:Rock
RETURN
-
T.DISP
REMOTE CONTROLLER
RC5001SR
(Using the remote control unit)
INFO
BASS
ON
SIGNAL:MARGINAL
Note:
To change the display content from XM information to
SR5001 functions, do so with the DISPLAY button.
SPKR A/B
OFF
BASS
C A T : R o c k
REC
ENTER
DISC+
When the channel category is displayed:
MULTI/ CAT
SET
l/
SLEEP
XM INFORMATION
XM
CHAN
NAME
TITLE
CAT
1.
BASS
SOURCE
1.
MAIN VOLUME
-------------------MAIN
RETURN
EXIT
3.
You can search for the channel you want to listen to
using one of three search modes. You can also enter
the number directly to select the desired channel.
ALL CHANNEL SEARCH MODE
SURR-MODE:AUTO
MULTIROOM:ON
MULTISPKR:OFF
M o n e y
The “NAME/TITLE” is displayed for 2 seconds,
followed by the artist’s name and song title.
(If artist’s name or song title is more than 13 characters
long, the text is scrolled.)
CH/ CAT
:DVD
:XM
PRESET SEARCH MODE
SEARCH MODE
Press the 1 or 2 cursor button on the front
panel to select the desired preset station.
(Using the remote control unit)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
3.
Press the BAND button to select XM band.
S or T button to tune in the desired
preset station.
Or enter the preset station number with the
numeric buttons.
7.
You can select the desired channel from the category
allocated to each channel.
Category being aired can be only selected.
1. 2. 3. 4.
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
CL
CH/ CAT
MEMO
VOLUME
EIVER SR5001
INFO
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
-
HT-EQ
MENU
EXIT
BAND
PRESET
+
-
TUNING
Note:
Category search automatically ends 5 minutes after
the last operation.
CHANNEL DIRECT CALL
You can select the desired channel by directly tapping
the numeric keypads on the remote control unit.
CLEA
ENTER
AUTO
MENU
3.
2.
You can return to the normal mode by press
the MULTI/CAT button during Category Search
Mode.
+
T-MOD
DISC+
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
DVD
VCR
AUDIO
4.
SOURCE
SET
OFF
ON
DISPLAY
P.DIRECT
SURROUND
dts
LIP SYNC/
INPUT
l/
SLEEP
AUTO
BASS
TREBLE
TV
1
DSS
CS
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
1.
3
EX/ES
VIRTUAL
4
5
6
M-CH ST
STEREO
NIGHT
7
REMOTE CONTROLLER
RC5001SR
2
CH/ CAT
The desired channel will automatically be
tuned.
Note:
If there is no input on the keypad for 5sec., the input is
cancelled to return to the original display
Notes:
• “LOADING” is displayed while receiving the
channel or information.
• “UPDATING” is displayed while updating encryption
code.
• When the selected channel is not available, “XM - -” is dispIayed.
• “OFF AIR” is displayed while air is suspended (e.g.
midnight).
T.MODE
P.SCAN
8
9
7.1CH IN
A/D
HT-EQ
0
+10
MEMO
SPKR A/B
MUTE
CL
6.
ENGLISH
CATEGORY SEARCH MODE
3.
VOLUME
(Using the SR5001)
ENTER
1.
2.
3.
4.
5.
6.
EXIT
REC
Press the BAND button to select XM band.
-
Press the ENTER button on the front panel.
T.DISP
PRESET
DISC+
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
3.
Press the BAND button to select XM band.
Press the TUNER button twice within two
seconds on the remote.
Press the MULTI/CAT button.
Press the CAT 3 or CAT 4 button.
-
F.DIRECT
TUNING
SUB TITLE
V-OFF
ATT.
BASS
After selecting the Category, Press the 3 or 4
cursor button to select the desired station of the
category.
You can return to the normal mode by press the
ENTER button during Category Search Mode.
+
PTY
ANGLE
CH-SEL
Press the 1 or 2 button on the front panel to
select the desired Category.
(Using the remote control unit)
4.
5.
6.
T.TONE
/SET UP
Turn the INPUT SELECTOR knob to select
“TUNER”.
+
2.
AUDIO
TREBLE
TV
DVD
VCR
TUNER
CD
CDR
DSS
MD
TAPE
AUX1
AUX2
AMP
1.
REMOTE CONTROLLER
RC5001SR
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
3.
Press the BAND button to select XM band.
4.
Press the F.DIRECT button.
Press the TUNER button twice within two
seconds on the remote.
“XM - - -” will appear on the display.
5.
Input the three digit number for your desired
Channel with the numeric keypad on the
remote control unit.
After selecting the category, Press the Q or
R button to select the desired station of the
category.
43
CHECKING THE XM PRESET CHANNEL
ENGLISH
PRESET MEMORY
You can store the desired channel in the Preset
Memory.
In addition to AM and FM, it is possible to preset 50
XM channels.
3.
SOURCE
2.4.
SET
OFF
CH/ CAT
DISPLAY
P.DIRECT
AUTO
dts
1
CS
2
3
EX/ES
VIRTUAL
CLEARING STORED PRESET STATIONS
CS
EX/ES
4
5
6
STEREO
NIGHT
7
8
MUTE
A/D
0
+10
P.SCAN
HT-EQ
MEMO
M-SPKR
CH/ CAT
You can remove preset stations from the memory
using the following procedure.
T.MODE
9
7.1CH IN
CL
MULTI/ CAT
VIRTUAL
M-CH ST
VOLUME
SPKR A/B
2. 5
2. 3.
AUTO
1
CS
VOLUME
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
VOLUME
ON
INFO
MENU
2.
l/
SLEEP
PRESET SCAN
The preset channel can be checked on the on screen
display.
SURROUND
LIP SYNC/
INPUT
ENTER
4
5
6
STEREO
NIGHT
7
8
9
7.1CH IN
A/D
CL
DOWN
EXIT
-
T.MODE
PRESET
+
-
TUNING
+
MPLE
ETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
3
VIRTUAL
M-CH ST
CH/ CAT
T.TONE
/SET UP
dts
2
EX/ES
0
+10
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
LIP SYNC/
INPUT
T.MODE
P.SCAN
HT-EQ
MEMO
VOLUME
MUTE
D
RROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
HT-EQ
MENU
5
6
STEREO
NIGHT
7
8
9
BAND
A/D
HT-EQ
0
+10
MEMO
VOLUME
CH/ CAT
EXIT
P.SCAN
7.1CH IN
CL
ENTER
AUTO
4
M-CH ST
SPKR A/B
MUTE
MULTI/ CAT
M-SPKR
T-MODE
D
3.
2.
BASS
ANGLE
SUB TITLE
CH-SEL
V-OFF
ATT.
DVD
VCR
AUDIO
TREBLE
TV
DVD
VCR
DSS
TUNER
CD
CDR
MD
TAPE
DISC+
AUX1
AUX2
AMP
BASS
1.
TV
4.
(Using the remote control unit)
1.
To select tuner, Press the TUNER button twice
within two seconds on the remote.
2.
3.
Press the BAND button to select XM band.
4.
Press the INFO button. to view a list of tuner
preset channeI on the on screen display.
5.
If there are 10 or more preset channel, Press
the INFO button. again.
Tune into the desired channel.
Press the MEMORY button on the front panel.
”- -” (preset number) starts blinking on the
dispIay.
- - X M 0 4 0
3.
Select the preset number by pressing the 1
or 2 cursor buttons, While this is still blinking
(approx. 5 seconds)
0 1 X M 0 4 0
4.
Press the MEMORY button again to enter.
The display stops blinking.
The station is now stored in the specified preset
memory location.
(Using the remote control unit)
1.
2.
Tune into the desired channel.
3.
Enter the desired preset number by pressing
the numeric buttons.
Press the MEMO button on the remote. “- -”
(preset number) starts blinking on the display.
Note:
When entering a single digit number (2 for example),
either input “02” or just input “2” and wait for a few
seconds.
44
Press the TUNER button twice within two
seconds on the remote.
XM
NO. 1
NO. 2
NO. 3
NO. 4
NO. 5
NO. 6
NO. 7
NO. 8
NO. 9
MAIN
Note:
The preset channel indication disappears in about 5
sec.
AUX 1 INPUT
S-VIDEO
VIDEO
INFO
MENU
TUNER
CD
CDR
MD
TAPE
AUX1
AUX2
AMP
1.
1.
Recall the preset number to be cleared with
the method described in “PRESET SERCH
MODE”.
2.
Press the MEMORY button on the front panel
or Press the MEMO button on the remote.
1.
Press the TUNER button twice within two
seconds on the remote.
2.
3.
Press the P.SCAN.
3.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for about 5-10 seconds each.
The time changes by the received condition.
No stored preset number will be skipped.
The stored preset number blinks in the display
for 5 seconds. WhiIe blinking, Press the
CLEAR button on the front panel or the remote
CL button.
4.
“xx CLEAR” appears on the dispIay to indicate
that the specified preset number has been
cleared.
4.
Pressing the T button during prescanning
speeds up scanning.
Also, pressing the S button returns to the
previous preset station.
PRESET LIST
XM010 XXXXXXXXXX
XM011 XXXXXXXXXX
XM015 XXXXXXXXXX
XM022 XXXXXXXXXX
XM125 XXXXXXXXXX
XM001 Preview
XM001 Preview
XM001 Preview
XM001 Preview
RETURN
EXIT
DIGITAL
DSS
REMOTE CONTROLLER
RC5001SR
1.
2.
ENTER
ENU
TREBLE
REMOTE CONTROLLER
RC5001SR
(Using the SR5001)
2.
3.
5.
When the desired preset station is received,
cancel the preset scan operation by press the
P. SCAN button.
Notes:
• To clear all stored preset stations, press and hold
the CLEAR (CL) and the ENTER buttons for two
seconds.
• There are 50 preset channels prepared at the factory
default. The 50 channels are all set to “CHANNEL
001”. Each channel can be stored in the preset
memory. You can search for only the preset
channels.
ENGLISH
TROUBLESHOOTING
If a problem should arise, first check the following.
1. Are the connections correct?
2. Have you operated the receiver according to the operating instructions?
3. Are the speakers and other components operating properIy?
If this unit is not operating properly, Check the items listed in the table beIow. Should the problem persist, there
may be a malfuncation. Disconnect the power immediately and contact your store of purchase.
SYMPTOM
CAUSE
REMEDY
“ANTENNA” is displayed.
XM terminal and the XM Connect-and- Check that the connection are correct.
Play antenna is not properly connected.
“NO SIGNAL” is displayed.
The signal cannot be received.
Reposition your XM Connect-and-Play
antenna.
Receiving only XM channels 0 and 1.
The XM Tuner is not activated.
Contact XM Radio.
45
ENGLISH
MULTI ROOM
SYSTEM (SR5001 only)
The Multi Room system is a function which allows
you to listen to the same or a different source in a
room other than the room in which the SR5001 is
located.
To use this function, a multi room remote unit and
remote control signal receiver available from your
Marantz dealer are necessary.
The operations possible with the multi room function
are explained briefly below.
For details, refer to the instruction manual supplied
with the multi room remote control unit and receiver.
MULTI ROOM PLAYBACK USING THE MULTI
ROOM OUT TERMINALS
MULTI ROOM PLAYBACK USING THE MULTI
SPEAKER TERMINALS
The SR5001 is equipped with audio pre-out terminals
for which the volume is adjustable as the MULTI
output terminals.
A separately sold stereo power amplifier can be
connected to enjoy multi room playback.
The MULTI OUT system can not be operated with the
supplied remote controller.
1.
2.
The SR5001 allows you to connect another set
of speakers and place them in a different room or
separated area for listening to music.
The MULTI ROOM SPEAKER system can not be
operated with the supplied remote controller.
2.
2.
DOWN
UP
VOLUME
MULTI
DOWN
UP
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
DISPLAY
MEMORY
MUTE
STANDBY
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
STANDBY
ATT
ENTER
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
CLEAR
ATT
ENTER
AUTO
POWER ON/STANDBY
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
1.
Press the MULTI SPEAKER button. The
unit enters multi room speaker mode and
the display indicates “SELCT SOURCE” and
flashes the “MULTI” indicators for approx. 10
seconds.
1.
Press the MULTI button. The unit enters multi
room mode and the display indicates “SELCT
SOURCE” and flashes the “MULTI” indicator
for approx. 10 seconds.
2.
2.
In this time, you can select the input source by
turning the input selector knob.
In this time, you can select the input source by
turning the input selector knob.
3.
Then, the display indicates “MSPKR VOLUME”
“MSPKR VOL.–18” for approx. 5 seconds.
During this time, you can set the volume level
in the multi room as desired.
This will only set the volume in the multi room.
Then, the display indicates “MULTI VOLUME”
“MULTI VOL. xx” for approx. 5 seconds.
3.
During this time, you can set the volume level
in the multi room as desired.
This will only set the volume in the second
room.
46
VOLUME
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
MULTI
SR5001 has some feature to MULTI ROOM SYSTEM
as source selector, sleep timer, Multi Room Speaker
output and remote control.
2.
INPUT SELECTOR
POWER ON/STANDBY
When the outputs of the MULTI OUT terminals are
wired and connected to amplifiers installed in other
rooms or M (MULTI) SPEAKER B terminals are
wired and connected to L&R speakers in other room,
different sources can be played in rooms other than
the main room in which this unit and the playback
devices are installed.
1.
AV SURROUND RECEIVER SR5001
Notes for MULTI ROOM SPEAKER
• MULTI ROOM SPEAKER On/ Off is available in
main room only.
• MULTI ROOM SPEAKER output terminals can
be used when the SURROUND BACK SPEAKER
is set NONE in SPEAKER SETUP menu. (See
SPEAKER SETUP, page 26)
• “The Surr. Back Speakers are in use” is displayed
by pressing the MULTI SPEAKER button when
the SURROUND BACK SPEAKER is set except
NONE in SPEAKER SETUP menu. (See SPEAKER
SETUP, page 26)
• Multi room operations cannot be performed from the
remote controller.
(SR4001 only)
The Surround Speaker B system is a function which
allows you to listen to the same source in a room other
than the room in which the SR4001 is located.
The operations possible with the Surround speaker
function are explained briefly below.
Notes for SURROUND SPEAKER B
• SURROUND SPEAKER B On/ Off is available in
main room only.
• SURROUND SPEAKER B output terminals can be
used when the SURROUND BACK SPEAKER is set
NONE in SPEAKER SETUP menu. (See SPEAKER
SETUP, page 26)
• “The Surr. Back Speakers are in use” is displayed
by pressing the S. SPEAKER B button when the
SURROUND BACK SPEAKER is set except NONE
in SPEAKER SETUP menu. (See SPEAKER SETUP,
page 26)
• Surround Speaker B function is unavailable, while
the unit is 7.1 CH input mode.
ENGLISH
SURROUND
SPEAKER B SYSTEM
ANOTHER ROOM PLAYBACK USING THE
S (SURROUND) SPEAKER B TERMINALS
The SR4001 allows you to connect another set
of speakers and place them in a another room or
separated area for listening to music.
The SURROUND SPEAKER B system can not be
operated with the supplied remote controller.
1.
2.
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
VOLUME
DOWN
MULTI
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
UP
MUTE
STANDBY
ATT
ENTER
POWER ON/OFF
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
1.
Press the S (Surround) SPEAKER B button.
The unit enters surround speaker B mode and
the “SPKR B” will appear on the display.
2.
The volume of S. SPEAKER B is interlocked
with the main volume.
47
ENGLISH
TROUBLESHOOTING
SYMPTOM
Can not select EX/ES mode.
In case of trouble, check the following before calling for service:
1.
Are the connections made properly ?
2.
Are you operating the unit properly following the user’s guide ?
3.
Are the power amplifiers and speaker working properly ?
If the unit does not operate properly, check items shown in the following table.
If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the
internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz
authorized dealer or the Marantz Service Center in your country.
SYMPTOM
CAUSE
REMEDY
Surround center= NONE has been Make the correct setting.
selected in SPEAKERS SIZE SETUP
Input signal is incompatible.
Use 5.1channel source.
Can not select Pro Logic IIx
mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select Neo:6 mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
Can not select CSII mode.
Input signal is incompatible.
Use 2 channel Dolby Digital input signal, PCM input
signal or analog input signal.
No output to Sub Woofer Out.
Sub-woofer = NONE has been selected in Select Sub-woofer = YES.
SETUP mode.
REMEDY
SR4001/SR5001 cannot be The power plug is not connected.
turned up.
Connect the power plug to the outlet.
Noise is produced during DTSencoded CD or laser disc play.
Analog has been selected for input.
Be sure to perform digital connection, select digital
input, then play.
No sound and picture are output Mute is on.
even when power is on.
The input cable is not connected correctly.
Cancel mute using the remote control unit.
A specific channel does not
produce output.
Nothing recorded on source.
Check the encoded channel on the source side.
See the connection diagram and connect the cables
correctly.
FM or AM reception fails.
Antenna connection is incomplete.
Correctly connect the indoor FM and AM antennas to
FM and AM antenna outlets.
Noise is heard during AM
reception.
Reception is affected by other electrical Try changing location where the AM indoor antenna
fields.
is set up.
Noise is heard during FM
reception.
The radio waves from the broadcasting Install an FM outdoor antenna.
station are weak.
The master volume control is turned all Adjust the master volume.
the way down.
The SOURCE position is wrong.
Select correct position.
No speaker output.
The headphones are connected to the Disconnect the headphones. (Speakers will not output
headphone jack.
sound when headphones are connected.)
Incorrect Audio or Video for
selected source.
Input cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Cannot get programmed station Preset data has been erased.
when the PRESET button is
pressed.
Disconnecting power plug for long periods of time will
erase preset data. If that happens, input the preset
data again.
Incorrect Audio from a channel.
Speaker cable connected incorrectly.
Connect the cable correctly by referring to the
connection diagram.
Control with the remote control
unit fails.
Replace all the batteries with new ones.
No Audio output from the center The center speaker cable connection is Connect the cable correctly.
channel speaker.
incomplete.
STEREO has been selected for Surround When STEREO is selected for Surround mode, no
mode.
sound will be output from the center speaker. Set
another Surround mode.
Center = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround speakers.
The surround speaker cable connection Connect the cable correctly.
is incomplete.
STEREO has been selected for Surround When STEREO has been selected for Surround
mode.
mode, no sound will be output from the surround
speaker. Set another Surround mode.
Surround = NONE has been selected in Make the correct setting.
SETUP mode.
No Audio output from the
surround back speakers.
The surround back speaker cable Connect the cable correctly.
connection is incomplete.
Surround mode is not EX/ES mode.
Set surround mode EX/ES.
Surround back = NONE has been selected Make the correct setting.
in SPEAKERS SIZE SETUP
48
CAUSE
Batteries are consumed.
Remote controller’s function-key setting Select different position from which equipment will
is wrong.
be controlled.
The distance between this SR4001/ Move closer to this SR4001/SR5001.
SR5001 and the remote commander is
too far.
Something is blocking SR4001/SR5001 Remove offending object.
and the remote commander.
Note:
After “PROTECT” appears on the unit’s display, the standby indicator may start flashing. If it does, there is a problem
in the unit or the connection. If this problem reoccurs even when power is activated from the remote control unit,
call for servicing.
after waiting at least three minutes, reconnect
the plug to the AC line supply
-
re-attempt to operate the equipment
Memory backup
• In case a power outage occurs or the power
cord is accidentally unplugged, the SR4001/
SR5001 is equipped with a backup function
to prevent memory data such as the preset
memory from being erased.
HOW TO RESET THE UNIT
Specifications subject to change without prior notice.
AM TUNER SECTION
Frequency Range ................................... 520 – 1710 kHz
Signal to Noise Ratio .............................................. 50 dB
Usable Sensitivity .................................... Loop 400mV/m
Distortion...................................400Hz, 30 % Mod. 0.5 %
Selectivity.................................................± 20 kHz 70 dB
DIMENSIONS
SURROUND
MODE
PURE
DIRECT
AUTO
HT-EQ
SIMPLE
SETUP
DISPLAY
MEMORY
CLEAR
EXIT
BAND
T-MODE
MUTE
ATT
ENTER
PHONES
MENU
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
Should the operation or display seem to be abnormal,
reset the unit with the following procedure.
To turn on the SR4001, press and hold the 7.1CH
INPUT and ATT buttons simultaneously for 3
seconds or more.
To turn on the SR5001, press and hold the MULTI
and ATT buttons simultaneously for 3 seconds or
more.
Remember that the procedure will reset the settings
of the SOURCE, Surround mode, delay time, TUNER
PRESET etc., to their initial settings.
Front L&R ..........................................6 ohms 105 W / Ch
Center ................................................6 ohms 105 W / Ch
Surround L&R ....................................6 ohms 105 W / Ch
Surround Back L&R ...........................6 ohms 105 W / Ch
13-7/16 ins.
(341 mm)
15-1/8 ins.
(384 mm)
MULTI
SPEAKER
STANDBY
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R ............................................8 ohms 80 W / Ch
Center ..................................................8 ohms 80 W / Ch
Surround L&R ......................................8 ohms 80 W / Ch
Surround Back L&R .............................8 ohms 80 W / Ch
Input Sensitivity/Impedance ...............168 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) .... 105 dB
Frequency Response
(Analog Input / Pure Direct)
........................................... 8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
............................................ 8 Hz – 45 kHz (± 3 dB)
AUDIO SECTION (SR5001)
13/16 ins.
(20 mm)
MULTI
UP
Remote Control Unit RC5001SR ................................... 1
AAA-size batteries ........................................................ 2
FM Antenna ................................................................... 1
AM Loop Antenna .......................................................... 1
Front AUX Jack Cover .................................................. 1
AC Power Cord ............................................................. 1
Warranty Card (USA × 1, Canada × 1)
Power Requirement .................................AC 120 V 60Hz
Power Consumption .............................................. 450 W
Weight ................................................. 25.1 lbs (11.4 Kg)
VOLUME
DOWN
ACCESSORIES
GENERAL (SR4001)
AUDIO SECTION (SR4001)
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
POWER ON/STANDBY
Frequency Range ................................ 87.5 – 108.0 MHz
Usable Sensitivity ............................IHF 1.8 µV/16.4 dBf
Signal to Noise Ratio ................... Mono/Stereo 75/70 dB
Distortion......................................Mono/Stereo 0.2/0.3 %
Stereo Separation .........................................1 kHz 45 dB
Alternate Channel Selectivity .................± 300 kHz 60 dB
Image Rejection .........................................98 MHz 70 dB
Tuner Output Level ........... 1 kHz, ± 75 kHz Dev 800 mV
Power Requirement .................................AC 120 V 60Hz
Power Consumption .............................................. 500 W
Weight ................................................. 27.1 lbs (12.3 Kg)
ENGLISH
-
FM TUNER SECTION
GENERAL (SR5001)
Television Format....................................................NTSC
Input Level/Impedance ........................... 1 Vp-p/75 ohms
Output Level/Impedance......................... 1 Vp-p/75 ohms
Video Frequency Response .......5 Hz to 8 MHz (– 1 dB)
Video Frequency (Component) ....5 Hz to 80 MHz (– 1 dB)
S/N .......................................................................... 60 dB
29/32 ins.
(23 mm)
disconnect the plug from the AC line supply
VIDEO
Power Output (20 Hz – 20 kHz/THD=0.08%)
Front L&R ............................................8 ohms 90 W / Ch
Center ..................................................8 ohms 90 W / Ch
Surround L&R ......................................8 ohms 90 W / Ch
Surround Back L&R .............................8 ohms 90 W / Ch
17-5/16 ins. (440 mm)
Front L&R ..........................................6 ohms 110 W / Ch
Center ................................................6 ohms 110 W / Ch
Surround L&R ....................................6 ohms 110 W / Ch
Surround Back L&R ...........................6 ohms 110 W / Ch
AV SURROUND RECEIVER SR5001
INPUT SELECTOR
DOWN
MULTI
Input Sensitivity/Impedance ...............168 mV/ 47 Kohms
Signal to Noise Ratio(Analog Input / Pure Direct) .... 105 dB
Frequency Response
(Analog Input / Pure Direct)
........................................... 8 Hz – 100 kHz (± 3 dB)
(Digital Input / 96 kHz PCM)
............................................ 8 Hz – 45 kHz (± 3 dB)
VOLUME
MULTI
SPEAKER
SURROUND
MODE
PURE
DIRECT
SIMPLE
SETUP
MEMORY
UP
CLEAR
MUTE
STANDBY
ATT
ENTER
AUTO
POWER ON/OFF
DISPLAY
PHONES
HT-EQ
MENU
EXIT
BAND
T-MODE
DIGITAL
AUX 1 INPUT
S-VIDEO
VIDEO
L
AUDIO
R
5-3/4 ins.
(146 mm)
6-5/16 ins.
(160 mm)
-
TECHNICAL
SPECIFICATIONS
9/16 ins.
(14 mm)
GENERAL MALFUNCTION
If the equipment malfunctions, this may be because
an electrostatic discharge or AC line interference has
corrupted the information in the equipment memory
circuits. Therefore:
49
SETUP CODES
TV
Acer .......................................................... 1141
Admiral .................................1002, 1009, 1089
Aiko .......................................................... 1059
Aiwa.................................................1117, 1118
Akai .......................................................... 1001
Amtron ...................................................... 1023
Anam ........................................................ 1113
Anam National......................1023, 1069, 1092
AOC............................1003, 1024, 1049, 1127
Audiovox .................................................. 1023
Bell & Howell ..................................1009, 1025
Benq ............................................... 1104, 1142
Broksonic ................... 1003, 1097, 1098, 1113
Celebrity ................................................... 1001
Citizen ..................................1003, 1013, 1023
1026, 1059, 1063
Colortyme .......................................1003, 1043
Contec ...................................................... 1113
Contec/Cony ........................1023, 1045, 1047
Craig ........................... 1020, 1022, 1023, 1113
Crown .............................................1023, 1067
Curtis Mathes .......................1003, 1013, 1025
1026, 1062, 1103, 1110
Daewoo ..................... 1003, 1013, 1024, 1035
1036, 1059, 1084, 1101
Daytron .................................1003, 1013, 1016
Dimensia .........................................1103, 1110
Dumont ................................. 1003, 1010, 1153
Electroband .............................................. 1001
Electrohome ...............1001, 1003, 1069, 1133
Emerson ...............................1003, 1013, 1015
1020, 1021, 1022, 1023
1025, 1038, 1044, 1045
1048, 1055, 1061, 1094
1096, 1099, 1101, 1113
Envision .................................................... 1003
Fisher .........................1025, 1051, 1091, 1160
Fujitsu ......................... 1038, 1124, 1125, 1155
Funai .................................... 1023, 1038, 1113
Gateway ................................................... 1150
GE ............................ 1003, 1018, 1022, 1046
1054, 1069, 1085, 1103
1110, 1113, 1133, 1136, 1153
Goldstar ................................1003, 1013, 1024
1030, 1045, 1080
1100, 1112, 1154
Hallmark ................................................... 1003
Hisense .................................................... 1116
Hitachi ....................... 1003, 1012, 1031, 1032
1037, 1041, 1045, 1047
1065, 1068, 1082, 1088
1094, 1139, 1140, 1145, 1159
Infinity ....................................................... 1067
Janeil ........................................................ 1134
JBL ........................................................... 1067
JC Penney............................1003, 1013, 1018
1019, 1024, 1026
1046, 1047, 1054
1063, 1083, 1085
1100, 1103, 1110
1112, 1133, 1154
Jensen ...................................................... 1003
JVC.......................................1028, 1029, 1045
1047, 1050, 1060, 1065
Kawasho ........................................1001, 1003
Kenwood .................................................. 1003
Kloss Novabeam ........1023, 1056, 1057, 1134
KTV ......................................1013, 1023, 1033
1034, 1073, 1099, 1113
LG...................................................1024, 1030
M.Wards ...............................1002, 1009, 1038
Magnavox.............................1003, 1052, 1053
1056, 1057, 1063
1067, 1081, 1106
Marantz ......................1003, 1031, 1067, 1122
Mitsubishi .............................1003, 1024, 1051
1115, 1122, 1133
Motorola .........................................1014, 1069
NEC ................. 1003, 1012, 1024, 1043, 1069
NET-TV .......................................... 1137, 1150
Orion...............................................1020, 1096
Panasonic ........ 1017, 1067, 1069, 1095, 1111
Philips .........................1003, 1011, 1045, 1052
1054, 1056, 1057, 1058
1063, 1067, 1069, 1106
Pioneer .................................1003, 1018, 1037
1070, 1071, 1094
1145, 1147, 1149
Plasmsync ................................................ 1135
Portland ..................... 1003, 1013, 1024, 1059
Price Club ................................................. 1026
Prism ........................................................ 1018
Proscan ..................... 1004, 1005, 1006, 1007
1008, 1085, 1103, 1110
Proton .............................................1003, 1045
Quasar ............. 1010, 1069, 1073, 1111, 1153
Radio Shack .........................1003, 1013, 1015
1023, 1024, 1025, 1045
1100, 1103, 1110, 1113
RCA ......................................1003, 1004, 1005
1006, 1007, 1008
1014, 1024, 1049, 1069
1075, 1079, 1085, 1087
1088, 1093, 1094, 1101
1103, 1110, 1113, 1153
Realistic ..................... 1013, 1015, 1023, 1025
1045, 1100, 1103, 1110
Runco ............................................. 1010, 1153
Sampo ...................................................... 1150
Samsung ................... 1003, 1013, 1024, 1026
1040, 1045, 1062, 1078
1083, 1090, 1100, 11051114
1120, 1121, 1146, 1148, 1157
Sansui ...................................................... 1119
Sanyo ........................ 1003, 1025, 1051, 1072
1077, 1091, 1156, 1157, 1158
Sharp ....................................1003, 1013, 1014
1015, 1045, 1055, 1064
1066, 1076, 1089, 1123
Signature .................................................. 1009
Sony ..................................... 1001, 1102, 1108
Soundesign ......1003, 1023, 1038, 1063, 1113
Starlite ...................................................... 1023
Supre-Macy .............................................. 1134
Sylvania ................................1003, 1039, 1042
1052, 1053, 1056, 1057
1063, 1067, 1089, 1151
Symphonic ...........................1023, 1039, 1044
Tandy ........................................................ 1014
Tatung....................................................... 1069
Technics ................................................... 1018
Techwood .......................................1003, 1018
Teknika ...................... 1003, 1009, 1013, 1023
1024, 1026, 1038, 1045
1047, 1059, 1063, 1111, 1113
Telecaption ............................................... 1074
Toshiba .................................1003, 1019, 1025
1026, 1042, 1074, 1098
1107, 1111, 1135, 1136
Totevision ................................................. 1013
Universal ........................................1046, 1054
i
Video Concepts ........................................ 1113
Viewsonic ............................. 1006, 1022, 1109
1128, 1129, 1130, 1131
1138, 1143, 1145, 1150
Wards ...................................1003, 1009, 1015
1024, 1038, 1044, 1046
1052, 1054, 1056, 1057
1067, 1086, 1103, 1110
White Westinghouse ...................... 1001, 1101
Yamaha ..........................................1003, 1024
Zenith ...................................1003, 1009, 1010
1132, 1144, 1153
VCR
Admiral ...........................................3026, 3060
Adventura ................................................. 3035
Aiko .......................................................... 3038
Aiwa................................................3035, 3039
Akai ................................................3003, 3053
3054, 3072, 3073
American High.......................................... 3009
Asha ......................................................... 3021
Audio Dynamics ...................3034, 3040, 3083
Audiovox .................................................. 3052
Beaumark .......................................3017, 3021
Bell & Howell ............................................ 3029
Broksonic .......................................3029, 3075
Calix ......................................................... 3052
Candle ..................................3012, 3021, 3034
3038, 3050, 3052, 3056
Canon .............................................3008, 3009
Capehart .................................................. 3050
Carver.............................................3045, 3062
CCE ................................................3038, 3067
Challenger ................................................ 3078
Citizen ............. 3012, 3021, 3038, 3052, 3056
Colortyme .......................................3034, 3079
Colt ........................................................... 3067
Craig .......................... 3021, 3032, 3052, 3067
Criterion .................................................... 3067
Curtis Mathes .................................3008, 3009
3021, 3034, 3063
Cybernex .................................................. 3021
Daewoo ................................3035, 3038, 3050
Daytron ...........................................3038, 3050
DBX ......................................3034, 3040, 3083
Denon ....................................................... 3005
Dimensia ..............................3004, 3063, 3085
Dixon ..............................................3077, 3081
Dynatech .................................................. 3035
Electrohome ............................................. 3052
Electrophonic ........................................... 3052
Emerson .................... 3009, 3015, 3016, 3017
3018, 3019, 3022, 3035
3047, 3052, 3054, 3073
Fisher .............................................3029, 3032
Fuji..................................................3003, 3009
Funai ..............................................3035, 3056
Garrard ..................................................... 3035
GE ........................................3004, 3008, 3009
3021, 3028, 3058
3063, 3074, 3085
Go Video ..............................3021, 3036, 3037
3052, 3067, 3068, 3069
Goldstar ..................... 3021, 3031, 3034, 3052
Gradiente .......................................3035, 3052
Harley Davidson ....................................... 3035
Harman Kardon..............................3034, 3045
Harwood ................................................... 3067
Headquarter ............................................. 3029
Hitachi ............. 3004, 3005, 3055, 3072, 3074
Homeline .................................................. 3052
Instant Replay .......................................... 3009
JBL ........................................................... 3002
JC Penney................. 3005, 3008, 3009, 3017
3021, 3029, 3034, 3040
3052, 3062, 3067, 3083
JCL ........................................................... 3009
Jensen ............................................3005, 3072
JVC.......................................3014, 3015, 3034
3040, 3041, 3042
3048, 3049, 3072, 3083
Kenwood ................... 3029, 3034, 3048, 3072
KLH .......................................................... 3067
Kodak .............................................3009, 3052
LG...................................................3031, 3052
Lloyds ...................................3034, 3035, 3056
Logik ......................................................... 3067
LXI ............................................................ 3052
Magnasonic ..........................3038, 3052, 3067
Magnavox.............................3008, 3009, 3010
3045, 3067, 3071
Magnin ...........................................3021, 3052
Marantz ................................3009, 3029, 3034
3040, 3045, 3062, 3083
Marta ........................................................ 3052
MEI ........................................................... 3009
Memorex ..............................3005, 3009, 3021
3026, 3029, 3032, 3035
3052, 3060, 3067, 3071
MGA ...............................................3022, 3073
MGN Technology ..................................... 3021
Midland ..................................................... 3056
Minolta ...................................................... 3005
Mitsubishi .............................3005, 3022, 3023
3025, 3048, 3052, 3073
Montgomery Ward..........................3026, 3060
Motorola ...............................3009, 3026, 3060
MTC................................................3021, 3067
Multitech ...............................3021, 3035, 3067
NEC ......................................3033, 3034, 3040
3048, 3072, 3083
Nikko ........................................................ 3052
Noblex ...................................................... 3021
Olympus ................................................... 3009
Optimus ................................3026, 3052, 3060
Optonica ................................................... 3027
Orion.......................... 3015, 3017, 3047, 3052
Panasonic ....... 3006, 3007, 3008, 3009, 3067
Pentax ..................................3005, 3034, 3074
Philco............... 3005, 3008, 3009, 3047, 3062
Philips .............. 3009, 3010, 3027, 3045, 3062
Pilot .......................................................... 3052
Pioneer .................................3005, 3040, 3046
3048, 3061, 3080, 3083
Portland .................................................... 3050
Proscan ................................3004, 3063, 3085
Protec ....................................................... 3067
Proton ....................................................... 3067
Pulsar ........................ 3021, 3038, 3056, 3071
Quarter ...........................................3029, 3084
Quartz.............................................3029, 3084
Quasar ...........................................3008, 3009
Radio Shack .............. 3021, 3052, 3009, 3008
3035, 3027, 3060, 3026
Radix ........................................................ 3052
Randex ..................................................... 3052
RCA ......................................3004, 3005, 3009
3021, 3046, 3054, 3057
3061, 3063, 3074, 3085
Realistic ..................... 3008, 3009, 3012, 3021
3026, 3027, 3029, 3032
3035, 3052, 3060, 3084
Ricoh ..............................................3002, 3059
Runco ....................................................... 3071
Samsung ..............................3013, 3020, 3021
3056, 3068, 3069, 3070
Sanky ...................................3026, 3060, 3071
Sansui ............. 3040, 3048, 3067, 3072, 3083
Sanyo ...................................3021, 3029, 3032
Scott .......................... 3012, 3017, 3022, 3052
Sears ....................................3005, 3009, 3029
3032, 3034, 3052, 3084
Sharp ......................... 3026, 3027, 3060, 3064
Shintom ................................3003, 3005, 3067
Shogun ..................................................... 3021
Signature ........................................3026, 3060
Signature 2000 .....................3026, 3029, 3084
Singer ........................ 3002, 3009, 3059, 3067
Sony .......................... 3001, 3003, 3043, 3065
STS ................................................3005, 3009
Sylvania ................................3008, 3009, 3022
3035, 3045, 3062, 3076
Symphonic ...........................3034, 3035, 3056
Tandy ..............................................3029, 3084
Tashiko ..................................................... 3052
Tatung....................................................... 3072
Teac ................................................3035, 3072
Technics .........................................3007, 3009
Teknika .................................3009, 3035, 3052
TMK .......................................................... 3021
Toshiba ................................. 3005, 3011, 3012
3022, 3051, 3073
Totevision .......................................3021, 3052
Unitec ....................................................... 3056
Unitech ..................................................... 3021
Vector Research ....... 3012, 3034, 3040, 3083
Victor ..............................................3040, 3083
Video Concepts ..............................3012, 3034
3040, 3073, 3083
Videosonic ................................................ 3021
Wards ...................................3005, 3009, 3012
3021, 3026, 3027
3032, 3035, 3045
3052, 3060, 3061, 3067
White Westinghouse ......................3035, 3056
XR-1000 ...............................3009, 3035, 3067
Yamaha ................................3029, 3034, 3040
3072, 3083, 3084
Zenith .............. 3030, 3052, 3053, 3059, 3071
ii
DVD
Aiwa................................................2036, 2037
Apex ...... 2012, 2017, 2018, 2019, 2021, 2034
BOSE .............................................2038, 2039
Denon .............................................2047, 2048
Funai ........................................................ 2049
GE ............................. 2009, 2020, 2029, 2033
Harman Kardon........................................ 2061
Hitachi ..................................2008, 2012, 2031
JVC.......................................2006, 2010, 2040
2041, 2042, 2043
Kenwood ........................................2053, 2054
Koss ......................................................... 2058
Magnavox...................2007, 2011, 2023, 2025
Marantz .................................................... 2025
Mitsubishi ....................................... 2011, 2015
Onkyo ....................................................... 2062
Oritron ............................................2009, 2030
Panasonic ................. 2003, 2015, 2016, 2055
Philips ................................... 2007, 2011, 2058
Pioneer .................................2002, 2014, 2056
Proscan ................................2009, 2020, 2032
RCA ................. 2005, 2009, 2020, 2035, 2057
Sampo ...................................................... 2041
Samsung ......... 2008, 2012, 2022, 2024, 2027
Sanyo .............................................2050, 2052
Sharp ..............................................2044, 2045
Sherwood ................................................. 2051
Sony .....................................2001, 2013, 2059
Toshiba ...................... 2004, 2008, 2026, 2028
Yamaha ..........................................2046, 2060
Zenith ....................................................... 2010
DSS
Alphastar .................................................. 4027
BSB .......................................................... 4021
Chaparral ................................................. 4039
DIRECTV .......................................4001, 4016
DISH Network .......................................... 4030
Drake ........................................................ 4026
Echostar .......... 4007, 4017, 4018, 4019, 4020
Express Vu ............................................... 4017
Fujitsu ....................................................... 4025
GE ........................................4002, 4008, 4009
General Instruments ......................4036, 4037
Hitachi ............................................4001, 4015
Hughes ...........................................4001, 4016
Janeil ........................................................ 4025
JVC........................................................... 4017
Mitsubishi ................................................. 4001
Panasonic ......................................4004, 4010
Philips .............................................4031, 4035
Proscan ......................4002, 4008, 4009, 4011
Radio Shack ...................................4036, 4037
RCA ........................... 4002, 4008, 4009, 4029
Realistic .................................................... 4040
Rural Cable .............................................. 4036
Samsung ........................................4022, 4027
Sony .....................................4003, 4012, 4014
Star Choice .............................................. 4032
Star Trak ................................................... 4024
STS .......................................................... 4038
SuperDish ................................................ 4028
Toshiba ...........................................4001, 4034
Uniden ..................................4005, 4006, 4013
Video Pall ................................................. 4025
Zenith .............................................4025, 4033
iii
www.marantz.com
You can find your nearest authorized distributor or dealer on our website.
is a registered trademark.
Printed in China
06/2006
00M03CW851250
ecmf-e