DeLonghi ceramic COOKTOPS Specifications

INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
BUILT-IN GAS HOBS
DEGH60
DEGH60ST
DEGH60WT
distributed by
DèLonghi
Pty Ltd
Dear Customer,
Thank you for having purchased and given your
preference to our product.
The safety precautions and recommendations reported
below are for your own safety and that of others. They
will also provide a means by which to make full use of
the features offered by your appliance.
Please keep this booklet in a safe place. It may be
useful in future, either to yourself or to others in the
event that doubts should arise relating to its operation.
This appliance must be used only for the task it has
explicitly been designed for, that is for cooking
foodstuffs. Any other form of usage is to be considered
as inappropriate and therefore dangerous.
The manufacturer declines all responsibility in the
event of damage caused by improper, incorrect or
illogical use of the appliance or be faulty installation.
PRODUCT LABEL
2
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR
USE OF ELECTRICAL APPLIANCES
Use of any electrical appliance implies the necessity to follow a series of fundamental
rules. In particular:
■ Never touch the appliance with wet hands or feet;
■
do not operate the appliance barefooted;
■
do not allow children or other incapable people to use the appliance
without supervision.
The manufacturer cannot be held responsible for any damages caused by improper,
incorrect or illogical use of the appliance.
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS
After having unpacked the appliance, check to ensure that it is not damaged.
In case of doubt, do not use it and consult your supplier or a professionally qualified
technician.
Packing elements (i.e. plastic bags, polystyrene foam, nails, packing straps, etc.) should
not be left around within easy reach of children, as these may cause serious injuries.
■ Do not attempt to modify the technical characteristics of the appliance as
this may become dangerous to use.
■ Do not carry out cleaning or maintenance operations on the appliance
without having previously disconnected it from the electric power supply.
■ After use, ensure that the knobs are in off position.
■
■
■
■
■
Do not allow children or other incapable people to use the appliance
without supervision.
During and after use of the hob, certain parts will become very hot. Do not
touch hot parts.
Keep children away from the appliance when it is in use.
Some appliances are supplied with a protective film on steel and aluminium
parts. This film must be removed before using the appliance.
The manufacturer declines all liability for injury to persons or damage to
property caused by incorrect or improper use of the appliance.
3
INSTALLATION
CAUTION:
■
■
■
■
■
■
This appliance must be installed in accordance with these installation
instructions, local gas fitting regulations, municipal building codes, water
supply regulations, electrical wiring regulations, AS5601 / AG 601 - Gas
Installations and ony other relevant statutory regulations.
This appliance shall only be serviced by authorized personnel.
This appliance is to be installed only by an authorised person.
Incorrect installation, for which the manufacturer accepts no responsibility,
may cause personal injury of damage.
Always disconnect the appliance from mains power supply before carrying
out any maintenance operations or repairs.
In the room where the cooker is installed, there must be enough air to
allow the gas to burn correctly, according to the current local regulations.
Figure 1
580
00
100
min
47
0
35
mi
n
5
550
DIMENSIONS (Table 2):
(Note: Also refer to Figure 1)
4
General Dimensions
Width
Depth
Depth Below Mounting Surface
Cut-out Dimensions
Width
Depth
580 mm
500 mm
30 mm
550 mm
470 mm
This cooktop has been designed and constructed in accordance with the following
codes and specifications:
AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances
AS/NZS 60335-1
General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NSZ 1044
Electromagnetic Compatibility Requirements.
CLEARANCES:
Installation clearances and protection of combustible surfaces shall comply with the
current local regulations e.g. AG 601 (AS 5601) - Gas Installations code.
100 m
m min
750 mm
450 mm
Figure 2
m
5m
min
3
500 m
m
5
The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind
that:
■
A minimum clearance of 20 mm has to be kept between the bottom of the
cooking hob and the top of an appliance or a shelf. To ensure this clearance
mount the spacers, supplied with the appliance, as shown in the figure below.
■
A partition between the base of the hob and the cupboard below should be
fitted 100 mm below the workbench surface if the cupboard is to be used
for storage.
■
Overhead clearances - In no case shall the clearance between the highest
part of the hob and a range hood be less than 600 mm, or for an overhead
exhaust fan, 750 mm. Any other downward facing combustible surface less
than 600 mm above the highest part of the hob shall be protected for the full
width and depth of the cooking surface area in accordance with local regulations in force. However, in no case shall this clearance to any surface be less
than 450 mm.
■
Side clearances - Where the dimension from the periphery of the nearest
burner to any vertical combustible surface is less than 200 mm, the surface shall
be protected in accordance with with local regulations in force to a height of
not less than 150 mm above the hob for the full dimension (width or depth) of
the cooking surface area.
Where the dimensions from the periphery of the nearest burner to any vertical
combustible surface is less than 200mm, the horizontal surface shall be greater
than 10 mm below the surface of the hob, or the horizontal surface requirement above.
■
Protection of combustible surfaces - Local regulations in force specify that
where required protection shall ensure that the surface temperature of the combustible surface does not exceed 65 °C above ambient. The fixing of 5 mm
thick ceramic tiles to the surface or attaching fire resistant material to the surface
and covering with sheet metal with minimum thickness of 0.4mm should be
satisfactory.
20 mm
Figure 3
6
INSTALLATION
(Refer to Figure 4):
1. Spread out the gasket “C” over the workbench at the edge of the cut out taking care to overlap the gasket at the corners.
2. Slot in the cooking hob into the cut out of the workbench and locate it correctly.
3. Adjust the clamps “A” and tighten the screws “B” until the hob is firmly secured.
4. Using a sharp tool, trim any excess gasket which protrudes from the edge of
the hob. Take care not to damage the countertop.
Figure 4
A
40 mm max.
B
20 mm min.
C
7
GAS SUPPLY:
■
This appliance is suitable for use with Natural Gas or ULPG. (Check the “gas type”
sticker attached to the appliance).
■
For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with
the two semi-rapid (SR) burners operating.
■
For ULPG models connect the gas supply directly to the appliance test point adaptor (supplied with the conversion kit) and ensure that the supply pressure is regulated to 2.75 kPa.
■
Do NOT force the ”elbow“ rotation prior to loosening nut.
■
Do NOT over tighten the nut at the ”elbow“.
1. After connecting the gas supply, check the piping and connections for leaks using a
soap and water solution. The presence of bubbles indicates a leak, tighten or
replace connections as appropriate.
Warning: Do not use any naked flame to check for leaks.
2. The operation of the appliance MUST be tested before leaving.
3. Adjust the test point pressure or supply pressure to the value which is appropriate
for the gas type.
4. Turn on the appliance gas controls and light each burner. Check for a well defined
blue flame without any yellow tipping. If any abnormality is evident then check that
the burner cap is located properly and the injector nipple is aligned correctly.
Figure 5a
Figure 5b
Gas connection for
NATURAL GAS
Gas connection for
ULPG
Gas inlet pipe
Gas inlet pipe
Test
point
Gasket
Gasket
Brass conical adaptor
Brass conical adaptor
(Thread tight: use
suitable seal)
(Thread tight: use
suitable seal)
Test point adaptor
Gas regulator
Test
point
8
5. Check the minimum burner setting by quickly rotating the gas control knob from
the maximum to the minimum position, the flame must not go out. If adjustment is
required carry out the “minimum burner setting adjustment" procedure described
below.
6. If satisfactory performance cannot be obtained, the installer shall check the installation and notify the local gas supply authority for a gas supply problem, or if it is an
appliance problem, our Customer Service Centre should be called to obtain the
nearest authorized Delonghi Service Agent.
7. Where the appliance data plate cannot be easily read with the appliance in the
installed position the duplicate data plate must be attached to adjacent surface and
the duplicate ULPG conversion label should also be included where a ULPG conversion has been completed.
INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY
■
If this appliance has to be installed with a hose assembly, the installer shall refer to
the network operator or gas supplòier for confirmation of the gas type, if in doubt.
■
The gas supply connection point shall be accessible when the appliance is
installed.
■
Installation with a flexible hose assembly shall be carried out by using a hose with
internal diameter of 16 mm minimum.
The thread connection shall be Rp 1/2" (ISO 7-1) male.
■
IMPORTANT WARNING: After connection the installer must check that the hose is
not kinked, subjected to abrasion or permanently deformed.
The installer must check also that the hose is not near (or in contact) with any hot
surfaces e.g. base of metal hotplate, underbench oven etc.
■
The hose assembly shall be as short as practicable and comply with relevant AS
5601/601 requirements.
■
IMPORTANT WARNING: The installer shall ensure the hose assembly is restrained
from accidental contact with the flue outlet of an underbench oven.
TABLE FOR THE CHOICE OF THE INJECTORS
Natural gas
1.0
Test Point Pressure [kPa]
BURNER
ULPG
2.75
Injector
Orifice Dia.
Gas
Consumption
Injector
Orifice Dia.
Gas
Consumption
[mm]
[MJ/h]
[mm]
[MJ/h]
Auxiliary (A)
0.85
3.6
0.53
3.6
Medium-speed burner (SR)
1.12
6.3
0.70
6.3
Triple-ring burner (TR)
1.55
11.9
0.94
11.9
9
CONVERSION PROCEDURE (to convert to Natural gas or to ULPG)
REPLACING THE INJECTORS
The conversion procedure must be carried out only by an authorised person.
This appliance is suitable for use with Natural gas or ULPG (check the “gas type” sticker attached to the appliance). The nominal gas consumption and injector size details
are provided in table at page 9.
To replace the injectors proceed as follows:
■ Remove pan supports and burners from the cooktop.
■ Using a spanner, remove the injector J (fig. 6, 7) and replace it with one
according to the gas type (see tables - page 9).
■ Affix to the appliance the warning label stating that the cooktop has been converted for use with ULPG (supplied with the ULPG conversion kit.).
A second ULPG conversion label should also be affixed to an adjacent surface
along with the duplicate data plate.
IMPORTANT
■ If the cooktop is suitable for use with Natural gas and must be converted for
use with ULPG, before connecting to gas main remove the appliance gas regulator and replace with test point adaptor (see fig. 5a, 5b)
■ If the cooktop is suitable for use with ULPG and must be converted for use
with Natural gas, before connecting to the gas main remove the appliance test
point adaptor and replace with gas regulator (see figs. 5a, 5b).
NOTE:
Gas regulator and test point adaptor are supplied with the appliance (packed with
conversion kit)
The burners are designed so that regulation of primary air is not required.
Figure 6
Figure 7
J
J
10
MINIMUM BURNER SETTING ADJUSTMENT
Check whether the flame spreads to all burner ports when the burner is lit with the
gas tap set to the minimum position. If some ports do not light, increase the minimum
gas rate setting.
Check whether the burner remains lit even when the gas tap is turned quickly from
the maximum to the minimum position. If the burner does not remain lit, increase the
minimum gas rate setting.
The procedure for adjusting the minimum gas rate setting is described below.
For taps with adjusting screw inside the shaft (fig. 8):
✓ using a screwdriver max. diameter 3 mm turn the screw inside the tap shaft until
the flame setting is correct.
For taps with adjusting screw on the body (fig. 9):
✓ using a screwdriver turn screw A until the flame setting is correct.
Normally for ULPG, fully tighten the adjustment screw.
LUBRICATING THE GAS TAP
If a gas tap is difficult to turn, disassemble it, clean it carefully with petrol and spread
a little high-temperature-resistant grease on it.
These operations must be performed by an Authorised person/Service agent.
Figure 8
Figure 9
A
11
ELECTRICAL REQUIREMENTS:
WARNING:
■
THIS APPLIANCE MUST BE EARTHED.
CAUTION:
■
■
Ensure that the power outlet is properly earthed before connecting the
appliance.
Disconnect power before servicing the appliance.
The appliance is provided with a standard 240VAC three pin plug and power
cable (3 x 0.75 mm2).
The wires in the power cable are coloured in accordance with the following code:
Green/Yellow = Earth, Blue = Neutral, Brown = Active.
If the colours of the wires in the power cable to the appliance do not correspond
with the coloured markings identifying the terminals in the junction terminal,
proceed as follows:
1. The wire which is coloured green and yellow must be connected to the
terminal marked E (Earth) or coloured Green.
2 The wire which is coloured blue must be connected to the terminal
marked N (Neutral) or coloured Black.
3. The wire which is coloured brown must be connected to the terminal
marked L (Live) or A (Active) or coloured Red.
If the supply cord is damaged it must be replaced by the manufacturer or it’s Service
Agent or a similarly qualified person in order to avoid a hazard.
Figure 10
N
L
M
ELECTRIC DIAGRAM KEY
A
PA
A
M
T
PA
12
PA
PA
PA
Ignition switches group
Ignition coil
Terminal block
Earth conductor
USE and CARE
CAUTION:
■
This appliance must be used only for the task it has explicitly been designed for,
that is for domestic cooking of foodstuffs. Any other form of usage is to be considered as inappropriate and therefore dangerous. Do not use this appliance as
a space heater.
■
Do NOT place combustible materials or products on this appliance at any time.
■
Do NOT spray aerosols in the vicinity of this appliance while it is in use.
■
Before using for the first time, clean the cooktop with warm soapy water.
■
Use the coffee pot support to ensure that small cooking utensils are stable.
■
IMPORTANT NOTE: This appliance shall not be used as a space heater,
especially if installed in marine craft or caravans.
13
GAS HOB
Figure 11b
Figure 11a
2
2
3
3
4
4
1
1
5 6 7 8
5 6 7 8
mod. DEGH60ST
mod. DEGH60WT
mod. DEGH60
■
■
■
The electric ignition is incorporated in
the knobs
This appliance is class 3
■
■
GAS BURNERS
1.
2.
3.
4.
Triple ring burner (TR)
Left semi-rapid burner (SR)
Right semi-rapid burner (SR)
Auxiliary burner (A)
Natural Gas
MJ/h
Propane gas
MJ/h
11.9
6.3
6.3
3.6
11.9
6.3
6.3
3.6
CONTROL PANEL
5.
6.
7.
8.
14
The hob is fitted with a safety cut-out
device
The electric ignition is incorporated in
the knobs
This appliance is class 3
Triple-ring burner control knob (1)
Left semi-rapid burner control knob (2)
Right semi-rapid burner control knob (3)
Auxiliary burner control knob (4)
LIGHTING GAS BURNERS
■
Check that the electricity is switched on to allow spark ignition.
■
Make sure that all controls are turned to zero.
■
The gas flow to the burner is controlled by the knobs on the safety taps.
■
You control the flow by turning the knob indicator to line up with the following
symbols:
■
– Symbol
: tap closed (burner off)
– Symbol
: High (maximum)
– Symbol
: Low (minimum)
■
To ignite automatically, simply push the required knob down and turn it to maximum, keep the knob down until the burner light.
You can control the temperature by the knob to “High” from “Minimum”.
■
To switch off, turn the knob clockwise until you hear the safety click.
■
Note that, if you are using a burner at the minimum setting, you turn the knob
clockwise past the maximum setting before reaching the off position.
Whenever lighting any of the burners produces an abnormal flame, switch that
burner off and relight using the minimum setting.
If after relighting the burner, the flame is still abnormal, turn the burner off and
contact our Customer Service Centre to obtain the nearest Authorised Delonghi
Service Agent.
In the case of a mains failure light the burner with a match or lighted taper.
■
■
■
■
Note: When the cooker top is not being used, set the gas knobs to their
closed positions and also close the cock valve on the gas bottle or the main gas
supply line.
Figure 12a
Figure 12b
mod. DEGH60ST - DEGH60WT
mod. DEGH60
15
Lighting the burners
WITH ELECTRIC IGNITION (without safety cut-off valve)
mod. DEGH60WT - DEGH60ST
To light one of the burners, press and turn the corresponding knob to the maximum
flow position (large flame) and keep the knob pressed down until the gas is lit.
Turn the gas tap to the position required.
Whenever lighting any of the burners produces an abnormal flame, switch that burner
off and relight using the minimum setting.
If after relighting the burner, the flame is still abnormal, turn the burner off and contact
our Customer Service Centre to obtain the nearest Authorised Delonghi Service Agent.
Lighting the burners
WITH ELECTRIC IGNITION (fitted with safety cut-off valve)
mod. DEGH60
In order to light the burner, you must:
1 – Turn the knob in an anti-clockwise direction to the maximum flow position,
push in and hold the knob down which will light the burner.
2 – Wait for about ten seconds after the gas burner has been lit before letting go
of the knob (valve activation delay).
3 – Adjust the gas valve to the desired position.
Important
16
■
If the burner flame should go out, the safety valve will automatically stop the
gas flow.
■
To re-light the burner, return the knob to the closed
position, wait for at
least 1 minute and then repeat the lighting procedure.
■
N.B. If your local gas supply makes it difficult to light the burner with the knob
set to maximum, set the knob to minimum and repeat the operation.
■
Whenever lighting any of the burners produces an abnormal flame, switch that
burner off and relight using the minimum setting.
■
If after relighting the burner, the flame is still abnormal, turn the burner off and
contact our Customer Service Centre to obtain the nearest Authorised Delonghi
Service Agent.
COOKING HINTS FOR GAS HOBS
The burner must be chosen according to the diameter of the pans and energy
required.
For optimum efficiency use a wok or pan no smaller than 230mm diameter.
Figure 13
do not use pans with concave or convex bases
Burners
Pan diameter
Auxiliary
Semi-rapid
Triple ring
Wok
*12 - 14 cm
16 - 20 cm
24 - 28 cm
max 36 cm
(*) with grill for small cookware: minimum diameter 6 cm.
Saucepans with handles which are excessively heavy, in relationship to the weight
of the pan, are safer as they are less likely to tip.
Pans which are positioned centrally on burners are more stable than those which
are offset.
It is far safer to position the pan handles in such a way that they cannot be
accidentally knocked.
When deep fat frying fill the pan only one third full of oil.
DO NOT cover the pan with a lid and DO NOT leave the pan unattended.
In the unfortunate event of a fire, leave the pan where it is and turn off all
controls.
Place a damp cloth or correct fitting lid over the pan to smother the flames.
DO NOT use water on the fire.
Leave the pan to cool for at least 30 minutes.
Figure 14
GRILL FOR SMALL
COOKWARE (fig. 14)
Put it on the auxiliary burner (the smallest) grid when small cookware is being
used to prevent the cookware from tipping over.
17
CORRECT USE OF TRIPLE-RING BURNER
■
The flat-bottomed pans are to be placed directly onto the pan-support.
■
To use the WOK, you must place the wok stand in the CORRECT position as
shown in fig. 15a - 15b.
IMPORTANT:
The special grille for wok pans (figs. 15a, 15b) MUST BE PLACED ONLY over the panrest for the triple-ring burner.
mod. DEGH60WT - DEGH60ST
Figure 15a
WRONG
CORRECT
mod. DEGH60
Figure 15b
WRONG
18
CORRECT
Cleaning and Maintenance
GENERAL TIPS
■
■
■
■
■
Before cleaning the hob switch it off and wait for it to cool down.
Clean with a cloth, hot water and soap or liquid detergent.
Do not use products which are abrasive, corrosive or chlorine based.
Do not use steel pads.
Do not leave acid or alkaline substances (vinegar, salt, lemon juice, etc.) on
the hob.
ENAMELLED PARTS
■
■
All the enamelled parts must be washed only with a sponge with soapy
water or other non-abrasive products.
Dry preferably with a microfibre or soft cloth.
STAINLESS STEEL HOB
■
■
■
Clean with special products which are available on the market.
Dry preferably with a microfibre or soft cloth.
Note: regular use will cause discolouring around the burners, because of
the high flame temperature.
BURNERS AND GRIDS
■
■
These pieces can be removed and washed with suitable products.
After cleaning burners and spreaders dry them well and replace them
correctly.
CONTROL KNOB
■
The control knobs may be removed for cleaning but care should be taken
not to damage the seal.
Do not use steam jet cleaners because the humidity could infiltrate into
the appliance making it dangerous.
19
GAS TAPS
■
■
Regular lubrication of the gas taps must only be performed by Authorised
person.
If the gas taps are not working properly, call our Customer Service Centre to
obtain the nearest Authorised Delonghi Service Agent.
CORRECT POSITIONING OF THE BURNERS
■
■
■
■
■
It is very important to check that spreader F and cap C of the burner (see
Figures 16 and 17) are perfectly in place because if they move out of place
serious problems could arise.
Make sure that electrode S (Fig. 16) is kept clean so that the sparks always
strike.
Model DEGH60 only: make sure that probe “T” (fig. 16) next to each burner
is kept clean to ensure correct operation of the safety valves.
Both the probe and ignition plug must be very carefully cleaned.
Note: To avoid damage to the electric ignition do not use it when the
burners are not in place.
Figure 16
Figure 17
C
F
T
S
20
CORRECT POSITIONING OF THE TRIPLE-RING BURNER
■
The triple ring burner must be correctly positioned (see fig. 20); the burner rib
must be located in position as shown by the arrow (see fig. 18).
■
The burner correctly positioned must not rotate (fig. 19).
■
Then position the cap A and the ring B (fig. 19).
Figure 18
Figure 20
Figure 19
A
B
21
SERVICE AND MAINTENANCE
If the ignition spark fails to ignite or does not light the gas, check the following
items before calling our Customer Service Centre to obtain the nearest Authorised
Delonghi Service Agent:
■
■
■
Burner is reassembled and located correctly.
Spark electrode and white ceramic are clean and dry.
240 VAC power supply is connected.
Contact the local gas utility or our Customer Service Centre to obtain the nearest
Authorised Delonghi Service Agent.
■
■
■
You can smell gas when all burners are turned on.
The burners do not remain alight at the minimum marked setting.
The burner flame is yellow or emits an unusual odour.
Note that a bi-annual inspection of the appliance by an authorised service agent or
your locate gas utility will ensure many years of trouble free operation of your
appliance.
Servicing the appliance:
Service may be obtained by contacting our Customer Service Centre to locate the
nearest Authorised Delonghi Service Agent:
22
Descriptions and illustrations in this booklet are given as simply indicative. The manufacturer reserves the right,
considering the characteristics of the models described here, at any time and without notice, to make eventual
necessary modifications for their construction or for commercial needs.
23
cod. 1103186 ß2