Woodstock SHOP FOX W1793 Owner`s manual

MODEL W1793/W1794
PROFESSIONAL
SPRAY GUN
W1793
(LVLP)
W1794
(HVLP)
OWNER'S MANUAL
Phone: (360) 734-3482 • Online Technical Support: tech-support@shopfox.biz
COPYRIGHT © JUNE, 2007 BY WOODSTOCK INTERNATIONAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
#9624CR PRINTED IN CHINA
�����������������������������������������������������������������������
��������������������������������������������������������������
����������������������������������������������������������������������
��������������������������������������������������������������������
������������������������
�����������������������������������������������������������������������
������������������������������������������������������������������������
�������������������������������������������������������������������
�����������������������������������������������������������������
����������������������������������������������������������������������
�����������������������������������������������
����������������������������������������������������������������
��������������������������������������������������������������������
�������
��������������������������������������������������������������������
�����������������������������������������������������������������������
����������������������������������������������������������������������
�������������������������������������
�� ����������������������������
�� ������������������������������������������������������������������
�� ����������������������������������������������������
������������������������������������������������������������������
������������������������������������������������������������������
��������������������������������������������������������������������
���������������������������������������������������������������������
��������������������������
Model W1793/W1794 Professional Spray Gun
SAFETY
For Your Own Safety Read Instruction Manual
Before Operating This Equipment
The purpose of safety symbols is to attract your attention to possible hazardous
conditions. This manual uses a series of symbols and signal words which are intended
to convey the level of importance of the safety messages. The progression of
symbols is described below. Remember that safety messages by themselves do not
eliminate danger and are not a substitute for proper accident prevention measures.
Indicates an imminently hazardous situation which, if
not avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if
not avoided, MAY result in minor or moderate injury.
It may also be used to alert against unsafe practices.
NOTICE
This symbol is used to alert the user to useful
information about proper operation of the
equipment.
Safety Instructions for Pneumatic Tools
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors
should be kept at a safe distance
from work area.
1. KEEP ALL SAFETY DEVICES IN
PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking
to see that keys and adjusting
wrenches are removed from tool
before operation.
6. MAKE WORKSHOP CHILD PROOF by
locking your shop and shutting off
air valves.
7. DO NOT FORCE TOOL. It will do
the job better and safer at the rate
for which it was designed.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DO NOT USE IN DANGEROUS
ENVIRONMENT. Do not use
pneumatic tools in damp or wet
locations, or where any flammable
or noxious fumes may exist. Keep
work area well lighted.
8. USE THE RIGHT TOOL. Do not
force tool or attachment to do a
job for which it was not designed.
9. DO NOT USE UNDER THE
INFLUENCE OF DRUGS OR
ALCOHOL.
-1-
Model W1793/W1794 Professional Spray Gun
Safety Instructions for Pneumatic Tools
10. USE PROPER AIR HOSE for the
tool. Make sure your air hose is in
good condition and is long enough
to reach your work without
stretching.
17. DISCONNECT TOOLS before
servicing, changing accessories, or
moving to another location.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets, or
other jewelry which may get
caught in moving parts. Non-slip
footwear is recommended. Wear a
protective hair covering to contain
long hair.
19. USE THE RECOMMENDED
ACCESSORIES. Consult owner’s
manual for recommended
accessories. The use of improper
accessories may cause risk of
injury.
18. DO NOT OVERREACH. Keep proper
footing/balance at all times.
20. CHECK FOR DAMAGED PARTS
BEFORE USING. Check for binding
and alignment of parts, broken
parts, part mounting, loose bolts,
and any other conditions that
mayaffect machine operation.
Repair or replace damaged parts.
12. ALWAYS USE SAFETY GLASSES.
Also use a face or dust mask
if cutting operation is dusty.
Everyday eyeglasses only have
impact resistant lenses, they are
NOT safety glasses.
21. NEVER LEAVE UNATTENDED TOOL
CONNECTED TO AIR. Disconnect
the air hose and do not leave tool
until it is relieved of any built up
pressure.
13. WEAR APPROVED HEARING
PROTECTION. Air escaping from
pneumatic tools can exceed safe
exposure limits and may cause
hearing damage with prolonged
exposure.
22. NEVER ALLOW UNTRAINED
USERS TO USE THIS TOOL WHILE
UNSUPERVISED.
14. SECURE WORK. Use clamps or a
vise to hold work when practical.
It is safer than using your hand
and frees both hands to operate
tool.
23. IF YOU ARE UNSURE OF THE
INTENDED OPERATION, STOP
USING TOOL. Seek formal training
or research books or magazines
that specialize in pneumatic tools.
15. MAINTAIN TOOLS WITH CARE.
Keep tools lubricated and clean
for best and safest performance.
Follow instructions for lubricating
and changing accessories.
24. BE AWARE OF HOSE LOCATION
WHEN USING PNEUMATIC TOOLS.
Hoses can easily become a tripping
hazard when laid across the floor
or spread out in a disorganized
fashion.
16. REDUCE THE RISK OF
UNINTENTIONAL FIRING. Do not
carry tool with hand on trigger
and always disconnect from air
when not in use.
-2-
Model W1793/W1794 Professional Spray Gun
Additional Safety Instructions for Spray Guns
1.
READ THIS MANUAL. This manual
contains proper operating
instructions for this spray gun.
2.
READ MATERIAL LABELS and
MATERIAL SAFETY DATA SHEETS
(MSDS). Read and know all the
instructions on the packaging label
and the MSDS before opening the
package. This information could
save your life.
3.
ALWAYS WEAR A NIOSH
APPROVED RESPIRATOR WHEN
SPRAYING OR WORKING AROUND
FINISHING MATERIALS.
4.
FIRE EXTINGUISHERS. Always
have a fully charged multi class
or class B fire extinguisher in the
immediate area.
5.
FLAMMABLE MATERIAL. NEVER
spray near open flame or where
any spark could occur.
6.
FRESH AIR. Always provide
adequate exhaust to keep area
free of built up vapors, NEVER
spray in an enclosed space.
7.
DISCONNECT COMPRESSED AIR.
Always disconnect the spray
gun from compressed air before
cleaning, changing attachments or
when performing maintenance of
any kind on this tool.
8.
PROTECTIVE CLOTHING. Protect
exposed skin from overspray by
wearing a protective suit or other
approved garment.
9.
INAPPROPRIATE USE. DO NOT
point or shoot spray gun directly
at yourself or another person or
animals. Do not attempt to use
the spray gun for any other use
than it was intended.
10. STORAGE. Thoroughly clean and
dry spray gun before storage.
Store in an approved cabinet.
11. SOLVENTS. Always store solvents
and shop towels soaked in solvent
in approved containers.
12. EYE PROTECTION. Wear eye
protection whenever spraying or
cleaning. Solvents and chemicals
can cause serious eye injury,
which could lead to blindness.
13. OPERATING PRESSURE. DO NOT
exceed the recommended inlet air
pressure. Excessive pressure could
cause the spray gun to burst or
cause other internal equipment
damage.
14. LOCAL LAWS. Consult local
authorities regarding exhaust and
waste disposal requirements.
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to your individual working conditions. Use
this and other tools with caution and respect to avoid serious injury.
-3-
Model W1793/W1794 Professional Spray Gun
INTRODUCTION
Woodstock Technical
Support
W1793 Specifications
Type....................... LVLP Gravity Feed
Fluid Tip ............................... 1.5 mm
Air Consumption ...................3–3.9 CFM
Inlet Air Pressure ..... 2–3.5 Bar /29–50 PSI
Fluid Pressure ......... Greater Than 10 PSI
Material Capacity ......... 600 ml / 20 fl oz
Pattern Width ...................180–280 mm
This machine has been specially designed
to provide many years of trouble-free
service. Close attention to detail, ruggedly built parts and a rigid quality
control program assure safe and reliable
operation.
Woodstock International, Inc. is committed to customer satisfaction. Our intent
with this manual is to include the basic
information for safety, setup, operation,
maintenance, and service of this product.
W1794 Specifications
Type....................... HVLP Gravity Feed
Fluid Tip ............................... 1.4 mm
Air Consumption ................ 4.2–7.1 CFM
Inlet Air Pressure ..... 2–3.5 Bar /29–50 PSI
Fluid Pressure ......... Greater Than 10 PSI
Material Capacity ......... 600 ml / 20 fl oz
Pattern Width ...................180–250 mm
We stand behind our tools! In the
event that questions arise about your
machine, please contact Woodstock
International Technical Support at
(360) 734-3482 or send e-mail to:
tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot
problems and process warranty claims.
If you need the latest edition of this
manual, you can download it from
http://www.shopfox.biz.
If you have comments about this
manual, please contact us at:
Woodstock International, Inc.
Attn: Technical Documentation
Manager
P.O. Box 2309
Bellingham, WA 98227
Email: manuals@woodstockint.com
Read manual before operation.
Become familiar with the spray gun
safety and operation instructions
before beginning any work. Serious
personal injury may result if safety
or operational information is not
understood or followed.
-4-
Model W1793/W1794 Professional Spray Gun
SETUP
Unpacking
This tool has been carefully packaged for safe transportation. If you notice the tool
has been damaged during shipping, please contact your authorized Shop Fox dealer
immediately.
Inventory
The following is a description of the main components shipped with the Model W1793/
W1794. Lay the components out to inventory them.
Note: If you can't find an item on this list, check the mounting location on the tool
or examine the packaging materials carefully. Occasionally we pre-install certain
components for safer shipping.
Qty
W1793 Inventory (Figure 4)
A. Service Wrench .......................... 1
B. Spray Gun . .............................. 1
C. Filter ...................................... 2
D. Cup 600 ml ............................... 1
E. Cleaning Brush........................... 1
F. Bore Brush ............................... 1
G. Hose Fitting .............................. 1
Qty
W1794 Inventory (Figure 5)
A. Service Wrench .......................... 1
B. Bore Brush ............................... 1
C. Baffle Wrench ........................... 1
D. Spray Gun . .............................. 1
E. Filter ...................................... 2
F. Cup 600 ml ............................... 1
G. Regulator/Gauge ........................ 1
C
A
E
B
D
D
F
B
A
C
E
F
G
G
Figure 5. Model W1794 inventory.
Figure 4. Model W1793 inventory.
-5-
Model W1793/W1794 Professional Spray Gun
Assembly
1.
Controls
Insert the filter into the gun body
(see Figure 6).
Atomizing Cap
Cup
Fluid Control
Trigger
Pattern Control
Air Flow Control
W1794 Regulator
Figure 7. Controls.
1.
Fluid Control: Controls the volume
of material that travels through the
fluid tip.
Screw the cup onto the top of the
body.
2.
Attach the air hose to the spray gun
with a 1⁄4" NPT quick connect set-up
(not included).
Pattern Control: Adjusts the spray
pattern from a round pattern to a
wide fan.
3.
Air Flow Control: Controls the fluid
pressure inside the spray gun.
4.
Atomizing Cap: Controls the spray
pattern from vertical to horizontal.
5.
Trigger: Two stage trigger. Stage
one only releases compressed air for
blowing off the work piece. Stage two
sprays material.
6.
Cup: 600 ml plastic cup allows easy
viewing of material level. Includes a
vented cap.
7.
Regulator/Gauge: Regulates inlet
air pressure to the spray gun. On
either spray gun, the regulator can be
attached directly to the gun for onthe-spot air adjustments or directly
from the air source. On either spray
gun, DO NOT attach to an unregulated air source that exceeds 120 PSI.
Figure 6. Installing filter.
2.
3.
Note: You have the option of attaching the regulator/guage directly to
the gun as shown in the photos. Some
may find this awkward and would
rather mount the regulator/gauge
closer to the air source.
4.
Attach the spray gun to an air hose
regulated between 29 and 50 PSI.
Note: For the best results, use a hose
that will be dedicated for spray use
only. Do not use a hose that has been
used with an in-line oiler or other
possible contaminant.
Note: The W1793 spray gun regulator
must be purchased separately.
-6-
Model W1793/W1794 Professional Spray Gun
OPERATIONS
Spraying
The Model W1793/W1794 spray gun
is designed to spray low to medium
viscosity liquids, like lacquers, stains,
primers, multi-component paints,
acrylics, epoxies etc. It is ideal for auto
body touch-ups, woodworking projects,
or projects with hard to reach areas.
EXPLOSION HAZARD! DO NOT smoke
or have any source of flame or spark
near spraying. Vapors will explode if
ignited.
To use your spray gun:
1. Read and follow the material
manufacturer's instructions for
spraying, mixing, safety, disposal,
and any other instruction on the label
or Material Safety Data Sheet (MSDS).
2. Ensure the cup is securely tightened
and all other fittings are secure to
avoid air leaks or material spills.
3. Set the inlet air pressure (the air
coming to the spray gun) to the
lowest pressure recommended
in Specifications on Page 4 or
to the material manufacturer's
recommendations.
RESPIRATORY HAZARD! Always use
respirator rated for organic vapor and
solvent use when using spray equipment. Failure to protect your lungs
can lead to respiratory illness and
nervous system damage.
4. Adjust the atomizing cap to vertical
or horizontal. See Atomizing Cap
and Fan Adjustments on Page 9 for
further explanation.
5. Fill the cup with material.
6. Trial and error are necessary to
achieve the results you want along
with a fair amount of practice. Test
your material flow and spray pattern
on a piece of cardboard or some
scrap of material similar to your
project.
TOXIC FUMES! Always use an approved
spray booth or well ventilated area
when spraying. NEVER spray in an
confined space where toxic fumes
and flammable vapors can accumulate to deadly levels.
-7-
Model W1793/W1794 Professional Spray Gun
7. Adjust the fluid control knob to
start with a low volume of material
and keep the atomization as low
as possible. You will need to use a
combination of fluid control, inlet air
pressure, air flow control and stroke
speed to achieve the results you
want. Spray so the material wets out
nicely without running or sagging.
10. Begin spraying 2-3 inches before
the work piece and continue to the
end of the work piece. Continue the
motion for a few inches past the work
until you are ready for the return
stroke.
11. Maintain an even speed when
spraying.
��
12. Overlap
�� each stroke by 50%. This will
ensure even coverage, as shown in
Figure 9. Overlapping less than 50%,
as shown in the figure to the right,
may lead to missed spots or streaky
results.
8. Use the pattern control knob to
adjust the spray fan to your desired
pattern.
9. Keep the gun tip perpendicular,
parallel, and 6-8" from the work (as
shown in Figure 8) when spraying.
Do not allow your wrist to bend. This
will cause the gun to arc across the
surface and distribute the material
unevenly, possibly creating sags and
dry spots.
Yes
��
��
No
Figure 9. Overlap technique.
13. Spray stroke should have even
consistency and parallel edges. If it
doesn't, refer to Troubleshooting on
Page 12.
Figure 8. Spray technique.
NOTICE
Tipping spray gun may cause material
to spill out of the cup. Always hold the
spray gun perpendicular to the ground
to avoid potential spills and gravity
feed problems.
-8-
Model W1793/W1794 Professional Spray Gun
Atomizing Cap and Fan
Adjustments
Rotating the pattern adjustment control
in Figure 11 will give you a range
between the two patterns in Figure 12.
The atomizing cap needs to be adjusted
for horizontal or vertical spraying
patterns. Spraying in the wrong direction
may lead to material build up on the
atomizing cap horn. Many performance
problems are caused by clogged
atomizing holes on the atomizing cap
horns (see Cleaning on Page 10).
Pattern
Stroke
Pattern
Control
Figure 11. Set up for horizontal stroke
direction with vertical fan pattern.
Stroke
Pattern
Pattern
Control
Figure 10. Set up for vertical spray stroke
with horizontal fan pattern.
Figure 12. Fan adjustment.
-9-
Model W1793/W1794 Professional Spray Gun
CLEANING & LUBRICATION
Cleaning
5. Unscrew the atomizing cap with
your fingers and the fluid tip with
the service wrench. The fully
disassembled gun should look like
Figure 13.
Proper cleaning is the best way to ensure
trouble free performance from your
spray gun. If your gun is not thoroughly
cleaned, damage and poor spraying will
result. Problems caused by improper
cleaning will not be covered by the warranty. Clean the spray gun immediately
after each use.
6. Rinse these parts thoroughly in
solvent then dry with compressed air
or let air dry.
Note: If the small holes in the
atomizing cap become blocked, soak
in cleaning solvent. If the blockage
still exists, clear the blockage with
a small needle, taking great care
to not enlarge or damage the hole.
Damage to the hole will create a
disrupted spray pattern.
To clean your spray gun:
1. Spray a small amount of solvent
through the spray gun.
Note: Check with local laws
regarding this practice. If you are
spraying on a regular basis, spraying
solvents into the air may be illegal. A
cabinet style spray gun cleaner may
be required.
7. Use the cleaning brush with solvent
to clean the inner orifice and other
hard to reach areas on the outside of
the spray gun body.
2. DISCONNECT SPRAY GUN FROM AIR!
8. Wipe the rest of the gun body with a
shop towel and dry.
3. Unscrew the cup.
4. Disassemble the gun by unscrewing
the fluid control knob, removing the
spring and needle (Figure 13).
Fluid Tip
Atomizing
Cap
EXPLOSION HAZARD! Chlorinated
Solvents like Tricloroethane and
Methylene Chloride (methyl chloride)
can chemically react with aluminum
and may explode. Many parts in spray
guns are made of aluminum. Read
solvent label carefully before using
solvent.
Cup
Strainer
Needle
Fluid
Control
Knob
NOTICE
Spring
DO NOT soak the spray gun body in
solvent. Prolonged exposure to solvent
will rapidly deteriorate the spray gun
washers and seals. Ignoring this notice
will void your warranty.
Figure 13. Gun disassembled for cleaning.
-10-
Model W1793/W1794 Professional Spray Gun
Lubrication
Lubricate the following areas with
spray gun lube after cleaning:
A
A.
B.
C.
D.
E.
F.
F
B
E
C
D
Atomizing Cap Threads
Air Valve Packing
Trigger Pin
Air Flow Control Valve
Pattern Control
Fluid Control Knob
After each cleaning, apply a thin film
of petroleum jelly to the needle spring
before reassembling.
Figure 14. Lubrication points.
-11-
Model W1793/W1794 Professional Spray Gun
Troubleshooting
Symptom
Possible Cause
Possible Solution
Fluttering or
Spitting spray.
1. Dry or worn fluid tip seat
permits air to seep into fluid
passage.
2. Material level too low.
3. Fluid tip or strainer obstructed.
4. Dry needle packing.
1. Tighten fluid tip or replace
seat with new one.
1. Atomizing cap holes are
obstructed.
2. Build-up on top or bottom of
fluid tip.
3. Build-up on atomizing cap is
on needle seat.
1. Clear holes.
1. Left or right side horn holes
are plugged.
2. Build-up on left or right side
of fluid tip.
3. Build-up of material inside
atomizing cap.
1. Clear holes.
1. The material flow exceeds
the atomizing cap capacity.
2. Inlet air pressure is too low.
3. Material is too thick.
1. Lower fluid flow.
1. Volume control turned in too
far.
2. Inlet air pressure too high.
1. Increase volume.
3. Fluid pressure is too low.
3. Increase fluid pressure.
4. Material is too thin.
4. Adjust material.
1. No pressure at gun.
2. Fluid passages dirty.
1. Check air supply.
2. Clean gun, remove any
obstructions.
3. Open.
4. Refill.
Uneven top or bottom pattern.
Right or left arc
pattern.
Heavy deposit of
material in center.
Narrow center pattern.
No spray output.
3. Fluid control closed.
4. Out of paint.
-12-
2. Add material.
3. Clean.
4. Lubricate needle.
2. Clean.
3. Clean.
2. Clean.
3. Clean.
2. Increase inlet air pressure.
3. Thin material.
2. Reduce inlet air pressure.
Model W1793/W1794 Professional Spray Gun
Symptom
Possible Cause
Possible Solution
Excessive overspray.
1. Fluid pressure too high.
2. Gun is too far from surface.
1. Reduce fluid pressure.
2. Keep gun at recommended
distance.
3. Slow down and maintain
consistent, even parallel
stroke.
3. Spraying too fast.
1. Pattern adjustment screw is
not seating properly.
2. Atomizing cap is loose.
1. Clean or replace.
Runs and sags.
1. Damaged seal.
1. Replace damaged seals.
Material leaks from
cup.
1. Cap not secure.
2. Cup not tight on gun body.
3. Leaking from cap vent hole.
1. Tighten.
2. Tighten.
3. Hold gun upright do not
tilt.
Material leaks from
gun.
1. Fluid tip loose.
2. Dry or damaged seals.
3. Excessive pressure.
1. Tighten.
2. Replace seals.
3. Reduce pressure.
Thick dimpled finish aka "Orange
Peel."
1. Holding gun too close to surface.
2. Inlet air pressure too low.
3. Material not properly mixed.
1. Spray at recommended distance.
2. Check inlet air pressure.
3. Follow manufacturer's
instructions.
4. More surface prep is
required.
Unable to control
spray fan.
4. Surface is dirty or oily.
Dry Spray.
1. Inlet air pressure too high.
2. Gun too far from surface.
3. Gun stroke too fast.
2. Tighten atomizing cap.
1. Lower inlet air pressure.
2. Keep gun at recommended
distance.
3. Slow down and maintain
consistent even parallel
stroke.
Gun leaks from
fluid tip.
1. Debris will not let the needle
seat with the fluid tip.
1. Clean or replace both.
Contaminated
paint.
1. Water or oil in the air line.
1. Install an in-line air filter.
2. Replace air line.
-13-
Model W1793/W1794 Professional Spray Gun
W1793 PARTS LIST
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
PART�#
X1793001
X1793002
X1793003
X1793004
X1793005
X1793006
X1793007
X1793008
X1793009
X1793010
X1793011
X1793012
X1793013
X1793014
X1793015
X1793016
X1793017
X1793018
X1793019
X1793020
X1793021
X1793022
DESCRIPTION
LOCK�NUT
HOSE�FITTING
CLEANING�BRUSH
BORE�BRUSH
SERVICE�WRENCH
DIRECTION�SCREW
SEAL�WASHER
AIR�CAP
FLUID�NOZZLE
TRIGGER�LEVER
TRIGGER
SPECIAL�WASHER
VENTILATOR�HEAD
CUP�LID
CUP�
FILTER
FLUID�INLET�JOINT
INLET�VALVE
SWITCH�SPRING
SPRING�
O-RING�4.5�X�1.2
WASHER
REF
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
-14-
PART�#
X1793023
X1793024
X1793025
X1793026
X1793027
X1793028
X1793029
X1793030
X1793031
X1793032
X1793033
X1793034
X1793035
X1793036
X1793037
X1793038
X1793039
X1793040
X1793041
X1793042
X1793042
DESCRIPTION
NEEDLE�SLEEVE
O-RING�10.7�X�1.8
O-RING�8.5�X�1.2
SWITCH�POLE
NEEDLE�ADJ.�SCREW
NEEDLE�SPRING
NEEDLE�SCREW
NEEDLE�KNOB
O-RING�8.7�X�1.85
O-RING�4.5�X�1.8
SPECIAL�WASHER
GUN�BODY
AIR�INLET�
INLET�VALVE��
SPECIAL�WASHER
AIR�VALVE�SPRING
SPECIAL�WASHER
O-RING�3.3�X�1.5
ADJ.�KNOB
ADJ.�SCREW
O-RING�KIT
Model W1793/W1794 Professional Spray Gun
W1794 PARTS LIST
REF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26
PART�#
X1794001
X1794002
X1794003
X1794004
X1794005
X1794006
X1794007
X1794008
X1794009
X1794010
X1794011
X1794012
X1794013
X1794014
X1794015
X1794016
X1794017
X1794018
X1794019
X1794020
X1794021
X1794022
X1794023
X1794024
X1794026
DESCRIPTION
AIR�REGULATOR
BORE�BRUSH
BAFFLE��WRENCH
TOOL�WRENCH
AIR�INLET�JOINT
RETAINER
O-RING�6�X�2
PATTERN�ADJ�SCREW
SPECIAL�WASHER
PATTERN�ADJ�KNOB
PATTERN�ADJ
FLAT�HEAD�SCREW
FLUID�ADJ�KNOB
SEALING�CUP
FLUID�NEEDLE�SPRING
FLUID�ADJ�NEEDLE
HOOK
FLUID�INLET�JOINT
INLET�WASHER
FILTER
CUP�600ML
CUP�COVER
VENTILATOR�HEAD
RETAINER�4MM
TRIGGER
REF
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
-15-
PART�#
X1794027
X1794028
X1794029
X1794030
X1794031
X1794032
X1794033
X1794034
X1794035
X1794036
X1794037
X1794038
X1794039
X1794040
X1794041
X1794042
X1794043
X1794044
X1794045
X1794046
X1794047
X1794048
X1794049
X1794050
X1794051
DESCRIPTION
TRIGGER�LEVER�2
TRIGGER�LEVER�1
LOCKING�SPRING
PAINT�NEEDLE�WASHER
DIRECTION�SCREW
BAFFLE�WASHER
BAFFLE
FLUID�NOZZLE�1.4MM
ATOMIZATION�CAP
FLUID�CAP�WASHER
CAP�NUT
PIN�SPRING��
DIRECTION�SCREW
SPECIAL�WASHER
O-RING�8.5�X�1.2
SWITCH�KNOB
AIR�VALVE�BODY
SWITCH�SPRING
AIR�INLET�VALVE
AIR�VALVE�SPRING
SPECIAL�WASHER
O-RING�2.5�X�2.1
AIR�ADJUSTMENT�KNOB
AIR�ADJUSTMENT�SCREW
O-RING�KIT
WARRANTY AND RETURNS
Woodstock International, Inc. warrants all Shop Fox machinery to be free of defects
from workmanship and materials for a period of two years from the date of original
purchase by the original owner. This warranty does not apply to defects due directly
or indirectly to misuse, abuse, negligence or accidents, lack of maintenance, or
reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option,
the Shop Fox machine or machine part which in normal use has proven to be defective,
provided that the original owner returns the product prepaid to a Shop Fox factory
service center with proof of their purchase of the product within two years, and
provides Woodstock International, Inc. reasonable opportunity to verify the alleged
defect through inspection. If it is determined there is no defect, or that the defect
resulted from causes not within the scope of Woodstock International Inc.'s warranty,
then the original owner must bear the cost of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties
that may be implied by law, including any merchantability or fitness, for any particular
purpose, are hereby limited to the duration of this written warranty. We do not
warrant that Shop Fox machinery complies with the provisions of any law or acts. In
no event shall Woodstock International, Inc.'s liability under this warranty exceed the
purchase price paid for the product, and any legal actions brought against Woodstock
International, Inc. shall be tried in the State of Washington, County of Whatcom. We
shall in no event be liable for death, injuries to persons or property or for incidental,
contingent, special or consequential damages arising from the use of our products.
Every effort has been made to ensure that all Shop Fox machinery meets high quality
and durability standards. We reserve the right to change specifications at any time
because of our commitment to continuously improve the quality of our products.
Warranty Registration
Name ___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________ State ___________________________Zip ________________________
Phone # ______________________ Email __________________________Invoice # ___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
CUT ALONG DOTTED LINE
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1.
How did you learn about us?
_____ Advertisement
_____ Mail Order Catalog
2.
How long have you been a woodworker/metalworker?
_____ 0-2 Years
_____ 2-8 Years
____ 8-20 Years
_____ 20+ Years
3.
How many of your machines or tools are Shop Fox?
_____ 0-2
_____ 3-5
____ 6-9
_____ 10+
4.
Do you think your machine represents a good value?
_____ Yes
____ No
5.
Would you recommend Shop Fox products to a friend?
_____ Yes
____ No
6.
What is your age group?
_____ 20-29
_____ 50-59
7.
What is your annual household income?
_____ $20,000-$29,000
____ $30,000-$39,000
_____ $50,000-$59,000
____ $60,000-$69,000
8.
Which of the following magazines do you subscribe to?
____
____
____
____
____
____
____
____
____
____
9.
Cabinet Maker
Family Handyman
Hand Loader
Handy
Home Shop Machinist
Journal of Light Cont.
Live Steam
Model Airplane News
Modeltec
Old House Journal
____ Friend
____ Website
____ Local Store
____ Other:
____ 30-39
____ 60-69
____
____
____
____
____
____
____
____
____
____
Popular Mechanics
Popular Science
Popular Woodworking
Practical Homeowner
Precision Shooter
Projects in Metal
RC Modeler
Rifle
Shop Notes
Shotgun News
____ 40-49
____ 70+
____ $40,000-$49,000
____ $70,000+
____
____
____
____
____
____
____
____
____
Today’s Homeowner
Wood
Wooden Boat
Woodshop News
Woodsmith
Woodwork
Woodworker West
Woodworker’s Journal
Other:
Comments:__________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
_____________________________________________________________________________
___________________________________________________________________
___________________________________________________________________
FOLD ALONG DOTTED LINE
Place
Stamp
Here
WOODSTOCK INTERNATIONAL INC.
P.O. BOX 2309
BELLINGHAM, WA 98227-2309
FOLD ALONG DOTTED LINE
TAPE ALONG EDGES--PLEASE DO NOT STAPLE