DynaPro Installation and Operation Manual

Add to my manuals
26 Pages

advertisement

DynaPro Installation and Operation Manual | Manualzz
DynaPro
PIN Encryption Device
DynaPro Installation and Operation Manual
October 2013
Manual Part Number:
99875586-3.01
REGISTERED TO ISO 9001:2008
i
Copyright© 2007 - 2012
MagTek®, Inc.
Printed in the United States of America
Information in this document is subject to change without notice. No part of this document may
be reproduced or transmitted in any form or by any means, electronic or mechanical, for any
purpose, without the express written permission of MagTek, Inc.
MagTek is a registered trademark of MagTek, Inc.
MagneSafe™ is a trademark of MagTek, Inc.
MagnePrint® is a trademark of MagTek, Inc.
REVISIONS
Rev
Number
1.01
2.01
Date
August 15, 2012
September 10, 2013
3.01
October 25, 2013
Notes
Initial Release
Updates include: changing name from IPAD EMV to DynaPro;
including Ethernet and USB descriptions; updated dimensions;
updated images; updated formatting.
Updated screens in Section 4
Added Section 4.8 for EMV transaction
ii
FCC WARNING STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation of this device is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CUR/UR
This product is recognized per Underwriter Laboratories and Canadian Underwriter Laboratories 1950.
RoHS STATEMENT
When ordered as RoHS compliant, this product meets the Electrical and Electronic Equipment (EEE)
Reduction of Hazardous Substances (RoHS) European Directive 2011/65/EC. The marking is clearly
recognizable, either as written words like “Pb-free”, “lead-free”, or as another clear symbol ( ).
iii
Table of Contents
1
2
3
4
INTRODUCTION AND SPECIFICATIONS .................................................................................. 1
1.1
Product Description......................................................................................................... 1
1.2
Design Objectives ............................................................................................................ 1
1.2.1
Securing Personal Cardholder Data ....................................................................... 1
1.2.2
Protection for all Points within the Payment Infrastructure .................................. 1
1.2.3
Security and Ease of Integration by Design ........................................................... 1
1.2.4
Greater Flexibility Reduces Total Cost of Ownership ............................................. 1
1.3
Design Features .............................................................................................................. 2
1.4
Major Components .......................................................................................................... 3
1.5
Specifications .................................................................................................................. 5
1.6
Pinout on RJ-25 6-pin Connector ................................................................................... 6
SYSTEM REQUIREMENTS & DEVICE FEATURES ................................................................... 7
2.1
System Requirements ..................................................................................................... 7
2.2
Device Features............................................................................................................... 7
2.2.1
Physical and Electronic Security ............................................................................. 7
2.2.2
Sleep Mode .............................................................................................................. 7
2.2.3
Liquid Crystal Display............................................................................................... 7
2.2.4
Function Buttons (Soft Keys)................................................................................... 7
2.2.5
10-Digit Numeric Pad .............................................................................................. 7
2.2.6
Magnetic Card Reading ........................................................................................... 7
2.2.7
ICC Card Reading ..................................................................................................... 8
2.2.8
Contactless Card Reading ....................................................................................... 8
INSTALLATION ......................................................................................................................... 9
3.1
USB Installation ............................................................................................................... 9
3.2
Ethernet Installation...................................................................................................... 10
3.3
Privacy Shield Installation ............................................................................................. 11
3.4
Privacy Shield Removal ................................................................................................. 11
3.5
Mounting Dimensions ................................................................................................... 12
OPERATION............................................................................................................................ 13
4.1
Overview ......................................................................................................................... 13
4.2
Card Reading using the SCR ........................................................................................ 14
4.3
Manual Card Entry......................................................................................................... 14
4.4
Selecting the Card Type ................................................................................................ 15
iv
5
4.5
PIN Entry ........................................................................................................................ 15
4.6
Amount Verify ................................................................................................................ 16
4.7
Signature Capture ......................................................................................................... 16
4.8
Card Reading using the Smartcard Reader for an EMV Transaction ........................ 17
4.9
Status Codes ................................................................................................................. 19
MAINTENANCE ...................................................................................................................... 20
5.1
Cleaning ......................................................................................................................... 20
5.2
Adjusting the LCD .......................................................................................................... 20
v
FIGURES
Figure 1-1. DynaPro USB and ETHERNET ................................................................................ 2
Figure 1-2. Major Components (front) ..................................................................................... 3
Figure 1-3. With Privacy Shield ................................................................................................. 3
Figure 1-4. Major Components (back) ..................................................................................... 4
Figure 1-5. RJ25 6-Pin Connector ............................................................................................ 6
Figure 3-1. USB Interface ......................................................................................................... 9
Figure 3-2. Ethernet Interface ................................................................................................ 10
Figure 3-3. Installing the Privacy Shield ................................................................................ 11
Figure 3-4. Mounting Dimensions and Cable Access Hole................................................... 12
Figure 4-1. Example of Welcome Screen (Ready for a New Transaction) ........................... 13
Figure 4-2. Example of Swipe Card Screen ........................................................................... 14
Figure 4-3. Example of User Screen to Manually Enter Card Data ...................................... 14
Figure 4-4. Example of User Screen to Select Card Type ..................................................... 15
Figure 4-5. Example of User Screen to Enter PIN ................................................................. 15
Figure 4-6. Example of User Screen to Verify Amount .......................................................... 16
Figure 4-7. Example of User Screen to Enter Signature ....................................................... 16
Figure 4-8. Example of EMV card insertion ........................................................................... 17
Figure 4-9. Processing Screen................................................................................................ 17
Figure 4-10. Example of Enter PIN Screen for EMV Transactions ....................................... 18
Figure 4-11. Examples of Screen Approved, Declined or Terminated ................................. 18
Figure 4-12. Examples of Screen Remove Card ................................................................... 19
Figure 5-1. Adjusting the DynaPro’s LCD ............................................................................... 20
vi
1
INTRODUCTION AND SPECIFICATIONS
1.1
Product Description
The DynaPro is a secure PIN encryption device combined with MagTek’s 3-Track MagneSafe™
secure card reader. The DynaPro provides the most comprehensive end-to-end security solution
to prevent personal cardholder data breaches while bringing convenience and speed to Retail and
Financial transactions.
1.2
Design Objectives
1.2.1 Securing Personal Cardholder Data
The DynaPro immediately encrypts data at the point of swipe to safeguard personal information
encoded on the magnetic stripe. The encryption takes place within an encapsulated magnetic
read head as the card is swiped, eliminating the chance of intercepting clear text data. The
DynaPro’s data encryption scheme uses the industry standard TDEA (3DES) algorithm, which
offers merchants, processors, issuers and acquirers the flexibility to manage decryption services
themselves or to outsource, thereby avoiding the risk imposed by unproven, proprietary
encryption algorithms.
1.2.2 Protection for all Points within the Payment Infrastructure
In addition to meeting the requirements established by PCI PTS v3.x, which incorporates SRED
features, the DynaPro has MagnePrint®, a proven embedded security feature that authenticates
the debit, credit, or gift card and its encoded track data, rendering counterfeit or cloned cards
useless. So even if cardholder data is acquired for the purpose of manufacturing counterfeit
cards, such cards can be detected, the transaction can be declined, and the criminal can be
prosecuted. The MagnePrint feature provides a valuable defense to protect the merchant, the
acquirer, the processor, the card issuer, and ultimately the consumer.
1.2.3 Security and Ease of Integration by Design
In addition to securing clear text card data, the DynaPro uses a 32-bit secure processor which
incorporates flexible data formatting and masking capabilities for compatibility with existing
software and payment applications, eliminating the need for recertification.
The DynaPro supports Device Authentication so the retailer, processor, and acquirer have the
confidence of knowing that a rogue reader was not substituted and provides transparency to the
processor, acquirer, or ISO if the device is changed. Furthermore, it supports Mutual
Authentication through a secure challenge/response sequence, which eliminates both the
potential of being redirected to an illegitimate site and the ability to substitute a compromised
PINpad terminal.
1.2.4 Greater Flexibility Reduces Total Cost of Ownership
The DynaPro supports secure remote key injection, eliminating the need to return the unit in the
event a new key is required.
1
Introduction and Specifications
1.3
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Design Features
PCI PTS v3.x, SRED Compliant
Meets EMV level 1 and 2 requirements
3 Track Secure Card Reader
Smart card EMV reader
Contactless reader (optional)
Backlit color LCD graphics
Optional real-time electronic signature capture
Optional privacy shield
16-digit key pad
Connectivity via USB HID or Ethernet
TDEA (3DES) Encryption
DUKPT Key Management
Remote Key Injection
Card and Data Authentication
Device Authentication
Mutual Authentication
Flexible Data Formats
Flexible Data Masking
Figure 1-1. DynaPro USB and ETHERNET
2
Introduction and Specifications
1.4
Major Components
The major components of the DynaPro are shown in Figures 1-2, 1-3 and 1-4.
Note: The ferrite bead must remain attached to the stylus cable at all times, do not remove.
Changes or modifications not expressly approved by MagTek could void the user's
authority to operate the equipment.
Figure 1-2. Major Components (front)
Figure 1-3. With Privacy Shield
3
Introduction and Specifications
Figure 1-4. Major Components (back)
4
Introduction and Specifications
1.5
Specifications
Electrical
Power Input:
Voltage:
Current:
Interfaces:
Display Type:
Display Resolution:
Flash Memory:
Internal SDRAM memory:
Battery type:
USB Bus Powered (Power adaptor required for contactless
or Ethernet)
5VDC
250mA (900mA with contactless)
USB 2.0 (USB 1.1 compatible) and Ethernet
Backlit, color liquid crystal display (LCD)
240 x 320 dpi
256 MBit
64 MBit
Lithium
Mechanical
Dimensions (L x W x H):
Weight:
Keypad:
Cable Length (standard):
Card Reader:
Connector Type:
8.8in x 3.9in x 2.4in (223.5mm x 99.1mm x 61.0mm)
1 lb
16-key, includes 3 soft function keys associated with LCD
6.75 ft (2 m)
3 track encrypting IntelliHead reader with MagnePrint
RJ25 modular jack
Environmental
Temperature:
Operating:
Storage:
32 °F to 113 °F (0 °C to 45 °C)
14 °F to 140 °F (-10 °C to 60 °C)
Relative Humidity:
Operating:
Storage:
10% to 90% non-condensing at 23 °C
Up to 90% non-condensing
Reliability
Expected Life (unit):
Battery Life:
1,000,000 card swipes (equivalent to 5 years of operation)
5 years shelf life
5
Introduction and Specifications
1.6
Pinout on RJ-25 6-pin Connector
RJ25
Connector
1
2
3
4
5
6
Signal
VBUS
USB_DM
USB_DP
GND
NC
CGND
Figure 1-5. RJ25 6-Pin Connector
6
2
SYSTEM REQUIREMENTS & DEVICE FEATURES
2.1
System Requirements
•
•
•
Windows XP or later (32-bit or 64-bit)
Microsoft .NET Framework version 2.0 (Not required but suggested)
USB port
Upon installation, Windows will automatically recognize and install the USB drivers for this
device.
2.2
Device Features
2.2.1 Physical and Electronic Security
The DynaPro enclosure and its associated electronics have been designed to form a Tamper
Resistant Security Module (TRSM). The covers are securely attached and incorporate sensing
circuits to detect if any attempt is made to open the unit. Internal spaces within the DynaPro
have been minimized to reduce the possibility of unauthorized modifications.
In addition, any attempt to penetrate or modify the DynaPro electronically will cause the unit to
permanently erase its stored encryption keys, after which the DynaPro will cease to function.
2.2.2 Sleep Mode
When the Windows operating system shuts down or is suspended the DynaPro will enter into a
sleep mode.
2.2.3 Liquid Crystal Display
The Liquid Crystal Display (LCD) is a color graphics display capable of showing static or
animated messages.
2.2.4 Function Buttons (Soft Keys)
The three function buttons or soft keys are located below the LCD screen. These buttons are
programmable for use with display-based prompts.
2.2.5 10-Digit Numeric Pad
During normal operation the numeric keypad is used for PIN entries. An audio tone will provide
feedback when entering the PIN digits. There are three additional keys that may be used during
a transaction: an ENTER button (green), a CLEAR button (yellow), and a CANCEL button
(red).
2.2.6 Magnetic Card Reading
The DynaPro contains a MagneSafe card reader that encrypts card data at the point of swipe to
protect the cardholder’s personal information. The reader incorporates MagTek’s 3-track
encrypting IntelliHead, a magnetic read head which has encapsulated and securely potted
electronics that reads, decodes, and encrypts card data within the head. This technology secures
the magnetic stripe data at the earliest point in the transaction chain—the initial swipe.
7
System Requirements and Device Features
In addition, as a card is swiped through the reader, through the use of MagnePrint technology the
card can be authenticated immediately, either by Magensa.net or by another system, to determine
whether the card is counterfeit or has been altered.
The card reader is capable of reading any ISO or AAMVA encoded magnetic stripe data.
2.2.7 ICC Card Reading
The DynaPro includes a smart card (ICC) reader. The card is inserted from the front of the unit
under the keypad.
2.2.8 Contactless Card Reading
The DynaPro includes an optional contactless card reader. The card is waved above the LCD.
8
3
INSTALLATION
3.1
USB Installation
To connect the DynaPro to a computer, connect its USB cable to the USB port on the computer
as shown in Figure 3-1. Note: the standard USB cable P/N 30019317 is six feet long.
Connecting or disconnecting the USB cable from the back side of the DynaPro
when the computer is ON may clear the encryption keys.
Figure 3-1. USB Interface
9
Operation
3.2
Ethernet Installation
Figure 3-2. Ethernet Interface
10
Operation
3.3
Privacy Shield Installation
To install the Privacy Shield, follow the steps below.
Place the clips of the open end of the Privacy Shield into the openings located just above the
contact card slot as shown in Figure 3-2.
Pivot the shield down, locking the three clips into the holes located just above the function
buttons.
Figure 3-3. Installing the Privacy Shield
3.4
Privacy Shield Removal
To remove the Privacy Shield, follow the steps below.
Grasp the Privacy Shield and slowly lift the edge closest to the LCD, pivoting the shield up to a
45 degree angle and remove the shield.
11
Operation
3.5
Mounting Dimensions
The overall dimensions of the unit and the mounting hole locations are shown in Figure 3-4.
This drawing is not to scale and dimensions are given in inches. In addition, mounting the
DynaPro to a surface will require size # 4-40 screws.
Notes: All dimensions are XX= +/- 0.02 in inches.
Figure 3-4. Mounting Dimensions and Cable Access Hole
12
Operation
4
OPERATION
4.1
Overview
During normal operation, the operator will select the type of transaction from the PC application
controlling the DynaPro and the cardholder will enter data on the DynaPro’s keypad in response
to prompts on its LCD. Transactions may include new accounts, teller window applications,
checking, savings, mortgages, retail transactions, or any other option where there is interaction
between the cardholder and the operator.
Messages shown on the DynaPro are customized by the application
programmer; therefore, the sequence of prompts on the LCD and their contents
will vary depending on the requirements of the institution and may not
correspond to the example messages contained herein. Refer to appropriate
personnel if there are any questions about the prompts or any part of the
operation.
The DynaPro will display “Welcome” on its LCD (see figure 4-1 for an example) to indicate that
it is ready to enter a new transaction.
Figure 4-1. Example of Welcome Screen (Ready for a New Transaction)
Typically, the cardholder is prompted to swipe his or her card through the DynaPro’s MSR to
initiate a transaction. If the card swipe failed to read the card data, the application may request
the user to re-swipe the card or may ask the user to enter the card data manually. The application
may also need to prompt the user to identify the card type (e.g. Debit or Credit). If a PIN is
required (e.g. for a Banking or Debit card transaction), the application will prompt the cardholder
to enter his or her PIN. If your DynaPro has signature capture capability, the application will
prompt the user to enter his or her signature on the touch screen. For a more detailed discussion,
see the sections below on Card Reading, Manual Card Entry, PIN Entry, and Signature Capture.
13
Operation
4.2
Card Reading using the SCR
When the appropriate prompt appears (see Figure 4-2 for an example), swipe the card with the
magnetic stripe down and facing toward the keypad of the DynaPro as indicated in Figure 4-2
below. If the magnetic stripe data could not be read, the application may prompt the user to
swipe the card again.
Figure 4-2. Example of Swipe Card Screen
4.3
Manual Card Entry
If the swiped card’s magnetic stripe is damaged or unreadable, the application controlling the
DynaPro may prompt the cardholder to enter information from his or her card manually, as
shown in the following example:
Figure 4-3. Example of User Screen to Manually Enter Card Data
The account number field can be configured with a minimum of 9 and a maximum of 19 digits,
or a minimum of 14 and a maximum of 21 digits. Expiration date consists of 4 digits. The card
verification code can be 3-4 digits in length.
14
Operation
4.4
Selecting the Card Type
In a retail setting, the transaction might require the user to select the card type (e.g. “Debit or
Credit”). In the following example, the application prompts the user to press the Left function
key if the card is a Credit card or to press the Right function key if the card is a Debit card:
Figure 4-4. Example of User Screen to Select Card Type
4.5
PIN Entry
When PIN entry is required, the LCD will prompt the cardholder to enter his or her PIN (the PIN
field has a minimum of 4 and a maximum of 12 digits for PIN entry) as required by the financial
institution (see figure 4-5 for a sample LCD display). After the cardholder has entered a PIN, the
ENTER key must be pressed.
.
Figure 4-5. Example of User Screen to Enter PIN
If the double PIN entry option is enabled, the LCD will prompt the cardholder to reenter his or
15
Operation
her PIN for confirmation. The user must repeat the above process and enter the correct PIN a
second time, followed by the ENTER key.
4.6
Amount Verify
In a retail setting when the customer selects “Credit” they are then prompted to verify the amount
of the transaction. The customer can select “Yes “or “No” as shown in the following example:
Figure 4-6. Example of User Screen to Verify Amount
4.7
Signature Capture
If your DynaPro has signature capture capability, the LCD will prompt the cardholder to enter a
signature to complete the transaction (see figure 4-7 for a sample LCD display). After the
cardholder has entered his or her signature, the ENTER key must be pressed.
Figure 4-7. Example of User Screen to Enter Signature
16
Operation
4.8
Card Reading using the Smartcard Reader for an EMV Transaction
An EMV transaction is started by the host sending an amount to be approved by a cardholder, as
shown in Amount Verify.
After the cardholder accepts the amount, the device will prompt the cardholder to insert his
smartcard by showing:
When the appropriate prompt appears (see Figure 4-8 for an example), insert the card with the
smartcard contacts facing up and the magnetic stripe facing down as indicated in Figure 4-8
below.
Figure 4-8. Example of EMV card insertion
The display will then show processing. If the Smartcard data could not be read, the application may
prompt the user to insert the card again
Figure 4-9. Processing Screen
17
Operation
Depending on the requirements of the smartcard, the device may ask for signature or PIN.
If PIN entry is required, the device will ask the cardholder to enter PIN using this screen:
Figure 4-10. Example of Enter PIN Screen for EMV Transactions
Processing continues, after which the DynaPro will show the outcome – whether the transaction
is APPROVED, DECLINED or TERMINATED.
Figure 4-11. Examples of Screen Approved, Declined or Terminated
Transaction data will be sent to the host, and as the last step of the EMV transaction process, the
DynaPro will ask the cardholder to remove the smartcard by displaying:
18
Operation
Figure 4-12. Examples of Screen Remove Card
4.9
Status Codes
The Device Offline screen indicates that the device is not ready for normal operation. There is
also a code in the lower right corner that can help explain the cause of the offline state. Codes
that start with H, S, C, or K indicate a problem with the unit that will require the device to be
returned to the supplier for service or replacement.
Code
Type
A
C
H
K
S
Description
An offline code beginning with "A" indicates the device is awaiting authentication. This
is a normal condition when a unit configured to require authentication (security level 4).
Authentication by the host application is required to return it to the "Welcome" screen.
An offline code beginning with "C" indicates the device is missing a certificate. It is
recommended that the device should be repaired or replaced.
An offline code beginning with "H" indicates there is a hardware problem with the
device. Should any H code be presented, it is recommended that the DynaPro be repaired
or replaced.
An offline code beginning with "K" indicates a problem with either the MSR or PIN key.
If it is a new device, it is likely due to the PIN Key not being loaded. A new device
showing this code should be returned to the supplier for Key loading. If the code appears
after being deployed and used for a long period of time, this code would be presented if
one or both DUKPT keys have been exhausted. If this is the case it is recommended that
you contact the supplier for a replacement.
An offline code beginning with "S" indicates a security element failure. This code can be
triggered through severe handling of the device or strong interference by a nearby EMF
source. If you move the device away from any suspected EMF source and the error
continues, the device should be repaired or replaced.
19
Maintenance
5
MAINTENANCE
5.1
Cleaning
Periodic cleaning of the DynaPro’s exterior may be required. To clean the outside of the
DynaPro, wipe down the unit with a soft, damp cloth and then wipe with a dry cloth.
Avoid excessive use of liquid cleaning products and do not attempt to clean the card path with
any objects other than approved cleaning cards or compressed air.
5.2
Adjusting the LCD
If it becomes necessary to adjust the LCD brightness or contrast, press the Left function key,
followed by “523” (corresponding to the letters “LCD”), followed by the Right function key.
The LCD will display the following screen:
Figure 5-1. Adjusting the DynaPro’s LCD
Once the above screen has displayed, press 1 to decrease, or 3 to increase, the brightness. Hit the
green arrow key to accept your brightness setting.
20

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement