American DJ Spherion Tri LED Instruction manual

Spherion Tri LED General Information
Unpacking: Thank you for purchasing the Spherion Tri LED by Amer-
ican DJ®. Every Spherion Tri LED has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Do not return this unit to your dealer without first contacting customer support.
Introduction: The Spherion Tri LED is part of American DJ’s continu-
ing pursuit for creating and upgrading affordable intelligent fixtures The
Spherion Tri LED is an DMX intelligent centerpiece. This fixture can be
used as a stand alone piece or connected in a Master/Slave configuration. The unit can sound active, run in a auto mode or be controlled via
DMX controller. When using DMX control the fixture has a 1 Channel
mode and a 3 Channel mode.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should you
encounter problems during your set up or initial operation. You may
also visit us on the web at www.americandj.com for any comments or
suggestions. Service Hours are Monday through Friday 8:00 a.m. to
4:30 p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
User Instructions
Rev. 8/11
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ®.
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 2
Spherion Tri LED General Instructions
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future
reference.
Spherion Tri LED Product Registration
The Spherion Tri LED carries a 3 year (1095 days) limited warranty.
Please fill out the enclosed warranty card to validate your purchase.
All returned service items whether under warranty or not, must be
freight pre-paid and accompany a return authorization (R.A.) number.
If the unit is under warranty, you must provide a copy of your proof of
purchase invoice. Please contact American DJ® customer support for
a R.A. number.
Spherion Tri LED Main Features
• Bright 3 Watt LED
• 2 DMX Channel Modes - 1 Channel Mode & 3 Channel Mode
• DMX-512 Compatible
• Master/Slave Operation
• 4 Operating Modes - DMX Control, Sound Active, Show Mode, & Program Mode.
• Optional UC3 Controller Compatible (Not Included)
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 3
Spherion Tri LED Safety Precautions
•To reduce the risk of electrical shock or fire, do not expose this unit rain or moisture
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to operate this unit if the power cord has been frayed or broken.
•Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical
shock and fire in case of an internal short.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Never operate this unit when it’s cover is removed.
•Never plug this unit in to a dimmer pack
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product out
doors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience recep-
tacles, and the point where they exit from the appliance.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 16 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the appliance.
C. The appliance has been exposed to rain or water.
D. The appliance does not appear to operate normally or exhibits a marked change in performance.
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 4
REMOTE
CONTROL
INPUT
SOUND
Spherion Tri LED
Set Up
matic voltage switch, which will auto sense the voltage when it is
plugged into the power source. With this switch there is no need to
worry about the correct power voltage, this unit can be plugged in
anywhere.
INPUT
OUTPUT
1
2
©American
3
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 5
OUTPUT
SOUND
POWER
DMX512
cables. Do not use
the
ground lug on the XLR connector. Do not conDMX+,DMX-,COMMON
nect the cable’s shield conductor to the ground lug or allow the shield
conductor to come in contact with the XLR’s outer casing. Grounding
the shield could cause a short circuit and erratic behavior.
COMMON
DMX512 OUT
3-PIN XLR
1
2
DMX +
3
DMX -
3
1
2
DMX512 IN
3-PIN XLR
3
1
2
Figure 2
XLR Female Socket
XLR Male Socket
1 Ground
2 Cold
2 Cold
1 Ground
XLR Pin Configuration
Pin 1 = Ground
Pin 2 = Data Compliment (negative)
REMOTE
CONTROL
INPUT
SOUND
INPUT
3 Hot
OUTPUT
SOUND
3 Hot
REMOTE
CONTROL
INPUT
OUTPUT
Pin 3 INPUT
= Data True (positive)
Figure 3
Special Note: Line Termination. When longer runs of cable are
POWER
Data Cable (DMX Cable) Requirements (For DMX and
Master/Slave
DMX512
DMX+,DMX-,COMMON
Operation): The Spherion Tri LED can be controlled via DMX-512 protocol. The Spherion Tri LED can be either a 1 or 3
channel DMX unit. The DMX address is set electronically using the controls on the rear panel of
the unit. Your unit and your DMX controller require
COMMON
a approved DMX-512 110 Ohm Data cable for data
DMX +
DMX512 OUT
input and data output (Figure 1). We recommend
3-PIN XLR
DMX Accu-Cable DMX cables. If you are making your
own cables, be sure to use standard 110-120 Ohm
Figure 1
shielded cable (This cable may be purchased at
almost all professional sound and lighting stores). Your cables should
INPUT
Notice: Be sure to follow figures two and three when making your own
tocol used by most lighting and controller manufactures as a form of
communication between intelligent fixtures and controllers. A DMX
controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture
via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX
fixtures (most controllers only have a DATA “OUT” terminal).
REMOTE
CONTROL
INPUT
REMOTE
CONTROL
INPUT
SOUND
POWER
DMX-512: DMX is short for Digital Multiplex. This is a universal pro-
SOUND
OUTPUT
Spherion Tri LED
Set Up
be made with a male and female XLR connector on either end of the
cable. Also remember that DMX cable must be daisy chained and
cannot be split.cable.
Power Supply: The American DJ® Spherion Tri LED contains a auto-
DMX Linking: DMX is a language allowing all makes and models
of different manufactures to be linked together and operate from a
single controller, as long as all fixtures and the controller are DMX
compliant. To ensure proper DMX data transmission, when using
several DMX fixtures try to use the shortest cable path possible. The
order in which fixtures are connected in a DMX line does not influence
the DMX addressing. For example; a fixture assigned a DMX address
of 1 may be placed anywhere in a DMX line, at the beginning, at the
end, or anywhere in the middle. Therefore, the first fixture controlled
by the controller could be the last fixture in the chain. When a fixture
is assigned a DMX address of 1, the DMX controller knows to send
DATA assigned to address 1 to that unit, no matter where it is located
in the DMX chain.
INPUT
POWER
POWER
used, you may need to use a terminator on the last unit to avoid erratic
behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and
DATA -). This unit is inserted in the female XLR connector of the last
unit in your daisy chain to terminate the line. Using a cable terminator
(ADJ part number Z-DMX/T) will decrease the possibilities of erratic
behavior.
3
1
2
DMX512 IN
3-PIN XLR
©American
3
1
2
Termination reduces signal errors and
avoids signal transmission problems
and interference. It is always advisable
to connect a DMX terminal, (Resistance
120 Ohm 1/4 W) between PIN 2 (DMX-)
and PIN 3 (DMX +) of the last fixture.
Figure 4
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 6
Termination
avoids signa
and interfere
to connect a
120 Ohm 1/4
and PIN 3 (D
Spherion Tri LED
Set Up
5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-
Spherion Tri LED
System Menu
512 data cables for DATA transmission in place of 3-pin. 5-pin DMX
fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used,
these adaptors are readily available at most electric stores. The chart
below details a proper cable conversion.
3-Pin XLR to 5-Pin XLR Conversion
Conductor
3-Pin XLR Female (Out)
5-Pin XLR Male (In)
Ground/Shield
Pin 1
Pin 1
Data Compliment (- signal)
Pin 2
Pin 2
Data True (+ signal)
Pin 3
Pin 3
Not Used
Pin 4 - Do Not Use
Not Used
Pin 5 - Do Not Use
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 7
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 8
Spherion Tri LED
System Menu
Operating Modes: The Spherion Tri LED can operate in four
different modes. In each mode you can run the fixture as a
stand alone fixture or in a master/slave confiugration. This next
section will detail the differences in the operating modes.
• Sound Active mode The fixture will react to sound.
• Show mode Choose 1 of 7 show modes to run.
• Program mode Choose 1 of 7 show modes to run.
• DMX control mode This function will allow you to control each individual fixtures traits
with a standard DMX-512 controller such as the Elation ® Show
Designer.™
System Menu: When making adjustments you can press
ENTER to confirm your setup or you can wait 8 seconds for
automatic setup. To exit without making any adjustments
press the MENU button.
ADDR - DMX Address Setting. See page 14 for more information on DMX Control.
1. Press the either the MENU, UP, or DOWN buttons until
“ADDR” is displayed, press ENTER.
2. The current address will now be displayed and flashing.
Press the UP or DOWN buttons to find your desired address.
Press ENTER to set your desired DMX address.
CHND - This will let select your desired DMX mode.
1. Press the either the MENU button until “CHND” is displayed,
press ENTER. Either “1CH” or “3CH” will be displayed
2. Press the UP or DOWN buttons to choose your desired DMX
mode and press ENTER to confim and exit.
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 9
Spherion Tri LED
System Menu
SLND - This will let you set unit as a master or slave in a
master/slave configuration.
1. Press the MENU button until “SLND” is displayed, press
ENTER. Either “MAST”,“SL 1” or “SL 2” will be displayed.
2. Press the UP or DOWN buttons until your desired setting is
displayed, press ENTER to confim.
NOTE: In a Master/Slave configuration you can set one fixture
to Master and then set the next fixture to “SL 2”, the fixtures will
now have contrast movement to each other.
SHND: SH 0 - SH 7 - Show modes 0-7 (Factory programs).
Show mode can be run with sound activity or without. For
show mode to run without sound activity turn sound activity
off.
1. Press the MENU button until “SHND” is displayed, press
ENTER.
2. “Sh X” will now be displayed, “X” representing a number
between 0-7. Programs 0-7 are factory programs, while “Sh 0”
is random mode. Press the UP or DOWN buttons to find your
desired show and press the ENTER, then press and hold the
MENU button for at least 3 seconds to confirm.
Note: While running a Show, you can change the show instantly
by pressing the UP or DOWN buttons.
PROG - In this mode you can choose 1 of 7 colors and control rotation and rotation speed.
1. Press the MENU button until “PROG” is displayed, press
ENTER.
2. “CoLo” will now be displayed, press ENTER. “CoLX” will now be
displayed, “X” representing a number between 1-7. Use the UP
or DOWN buttons to scroll through the different colors. Once you
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 10
Spherion Tri LED
have found your desired color press ENTER.
System Menu
3. Press the UP or DOWN button so that “ROTA” is displayed. In
this setting you can control rotation. Press the ENTER button,
“XXX” will be displayed. “XXX” representing a number between
0-255.
0-9 is no rotation, 10-113 is clockwise rotation fast-slow, 114-141 is no rotation, 142-245 is counter-clockwise rotation
slow-fast, and 248-255 is no rotation.
4. Adjust the rotation as you desire, then press ENTER.
SOUN - Sound Active mode.
1. Press the MENU button until “SOUN” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to activate sound active mode, or
“OFF” to deactivate sound active mode.
3. Press the ENTER, and then press and hold the MENU button
for at least 3 seconds to confirm.
SENS - Sound sensitivity control.
1. Press the MENU button until “SENS” is displayed, press
ENTER.
2. The display will show a number between 0-100. Press the UP
or DOWN buttons to adjust the sound sensitivity. 0 being the
least sensitive and 100 the most sensitive.
3. Press the ENTER, and then press and hold the MENU button
for at least 3 seconds to confirm.
Spherion Tri LED
ENTER. Either Yes or No will be displayed.
System Menu
2. To activate Blackout tap the UP or DOWN buttons until “Yes”
is displayed, press ENTER to confim. The fixture will now be in
Blackout mode. To deactivate Blackout mode, select “No” and
press Enter.
LED - With this function you can have the LED display turn
off after 10 seconds.
1. Press the MENU button until “LED” is displayed, press
ENTER.
2. The display will show either “ON” or “OFF”. Press the UP or
DOWN buttons to select “ON” to keep the LED display on at
all times, or “OFF” to switch to have the LED display switch off
after 10 seconds.
3. Press ENTER to confirm.
DISP - This will “flip” the LED display 180º.
1. Press the MENU button until “dISP” is displayed, press
ENTER.
2. Either “dISP” or “dSIP” will now be displayed. Press the UP or
DOWN buttons to select one or the other.
3. Press the ENTER, and then press and hold the MENU button
for at least 3 seconds to confirm.
TEST - This function will run a self test program.
1. Press the MENU button until “TEST” is displayed, press
ENTER.
BLND - Blackout or Stand by mode.
2. The fixture will now run a self test.
1. Press the MENU button until “BLND” is displayed, press
FHRS - With this function you can display the running time
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 11
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 12
Spherion Tri LED
of the fixture.
System Menu
1. Press the MENU button until “FHRS” is displayed, press
ENTER.
2. The running time of the fixture will now be displayed. Press
MENU to exit.
VER - With this function you can display the version software of the fixture.
1. Press the MENU button until “VER” is displayed, press
ENTER.
2. The software version will now be displayed. Press MENU to
exit
RSET - Use this function to reset the unit.
1. Press the MENU button until “RSET” is displayed, press
ENTER.
2. The fixture will now reset
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 13
Spherion Tri LED
DMX Control
Universal DMX Control: This function allows you to use a Elation®
universal DMX-512 controller to control the chases and patterns,
dimmer and strobe. A DMX controller allows you to create unique
programs tailored to your individual needs.
1. The Spherion Tri LED can be either a 1 or 3 DMX channel fixture. See page 15 for detailed description of the DMX values and traits.
2. To control your fixture in DMX mode, follow the set-up procedures
on pages 6-8 as well as the set-up specifications that are included with your DMX controller.
3. Use the controller’s faders to control the various DMX fixture traits.
4. This will allow you to create your own programs.
5. Follow the instructions on page 9 to set the DMX address.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
Spherion Tri LED
Master-Slave Configuration
Master-Slave Operation This function will allow you to link up to 16
units together and operate without a controller. The units will be sound
activated. In Master-Slave operation one unit will act as the controlling
unit and the others will react to the controlling units programs. Any unit
can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units togeth- er via the XLR connector on the rear of the units. Remember the Male XLR connector is the input and the Female XLR connector
is the output. The first unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the male XLR connector only. For longer cable runs we suggest a termina-
tor at the last fixture.
2. On the Master unit find and run your desired operating mode.
3. On the slave units tap the MENU button until “SLND” is dis-
played, and Press ENTER. See page 9 under “SLND” for more infomation.
4. The slave units will now follow the Master unit.
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 14
Spherion Tri LED
Channel
1
Value
1
2
3
©American
3 DMX Channel Mode - DMX Traits
Value
0-9
10 - 120
121 - 134
135 - 245
246 - 255
0-7
8 - 199
200 - 247
248 - 255
0 - 46
47 - 85
86 - 124
125 - 163
164 - 202
203 - 240
241 - 255
Function
SHOWS
BLACKOUT
SHOW 1
SHOW 2
SHOW 3
SHOW 4
SHOW 5
SHOW 6
SOUND ACTIVE
0-7
8 - 47
48 - 87
88 - 127
128 - 167
168 - 207
208 - 247
248 - 255
Spherion Tri LED
Channel
1 DMX Channel Mode - DMX Traits
Function
ROTATION
STOP
CLOCKWISE ROTATION FAST-SLOW
STOP
COUNTER-CLOCKWISE ROTATION
SLOW - FAST
STOP
DIMMER & STROBE
OFF
DIMMER 0% - 100%
STROBING FAST - SLOW
ON
COLOR
COLOR 1
COLOR 2
COLOR 3
COLOR 4
COLOR 5
COLOR 6
COLOR 7
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 15
Spherion Tri LED
UC3 Control
Blackout Blackout the unit
Select color
1. Red
2. Green
1. Synchronous Strobe in white 3. Blue
Select
Function 2. Asynchronous Strobe in whtie 4. Red+Green
Show(1-7)
3. Sound Strobe in color
5. Green+Blue
6. Red+Blue
7. Red+Green+Blue
8. Color change by sound
Mode
Sound
(LED OFF)
Spherion Tri LED
Manual Color
(LED ON)
Show(LED
slow
blinking)
Fuse Replacement
Disconnect the unit’s main power supply. Insert a standard flat head
screw driver in to the fuse holder housing. Turn the screwdriver in
counter-clockwise direction to remove the fuse holder. Remove the
old fuse and discard it, replace the fuse with the same type. Insert
the fuse holder back into it’s housing and turn in clockwise direction
to lock the holder in place.
Spherion Tri LED Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning the
internal and external optical lenses and mirror should be carried out
periodically to optimize light output. Cleaning frequency depends on
the environment in which the fixture operates (I.e. smoke, fog residue,
dust, dew). In heavy club use we recommend cleaning on a monthly
basis. Periodic cleaning will ensure longevity, and crisp output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Use a brush to wipe down the cooling vents and fan grill.
3. Clean the external optics with glass cleaner and a soft cloth every 20 days.
4. Clean the internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Always be sure to dry all parts completely before plugging the unit back in.
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 16
Spherion Tri LED Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
Spherion Tri LED Notes
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors which
have a 1-year (365 day Limited Warranty)
©American DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 17
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 18
Spherion Tri LED Specifications
Model: Spherion Tri LED
Voltage:
100v~240v/ 50~60Hz
LEDs:
5 x 3W 3-in-1 TRI LED
Colors:
RGB
Beam Angle:270 Degrees
Dimensions:
12.75” (L) x 8” (W) x 16.75” (H)
320mm x 190mm x 422mm
Weight:
11 Lbs. / 5 Kgs
Power Draw:
27W
Fuse:
1 Amp
Duty Cycle:
None
DMX: 1 or 3 DMX Channels
Working Position:
Any Safe, Secure Position
Warranty:
3 Year (1095 days)
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design
of this unit and this manual are subject to change without any
prior written notice.
©American DJ Supply
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-582-2610
Web: www.americandj.com / E-mail: info@americandj.com
©American
DJ® - www.americandj.com - Spherion Tri LED Instruction Manual Page 19
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99