Viper G4203V Instruction manual

0 W N E R' S
GU I DE
Contents
Government Regulations ............................... ............................... ...................... 2
Warning! Safety first ....... ............................... ............................... ....................3
What is Included ............................... ............................... ..............................5
Important Information ............................... ............................... ..........................5
Your Warranty ............................... ............................... ............................5
System Maintenance ............................... ............................... ...................5
Battery Replacement ............................... ............................... .................... 6
Using Your System ............................... ............................... ............................. 7
Unlocking ............................... ............................... ............................... ...7
Car Finder ............................... ............................... ............................... ..7
Ignition Controlled Door locks ............................... ............................... ...... 7
Remote Start ............................... ............................... ............................... 8
Valet Take-Over ............................... ............................... ........................ 10
Programming options ............................... ............................... ......................... 11
Glossary of Terms ............................... ............................... .............................. 1 1
Quick Reference Guide ............................... ............................... ...................... 13
limited lifetime consumer warranty ............................... ............................... ...... 15
Government Regulations
This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: ( 1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that
may cause undesirable operation.
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications . However, there is no guarantee
that interference will not occu,· in a particular installation . If this equipment does
cause harmful interference to radio or television, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Re-orient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
•
Consult the dealer or an experienced radio /
TV
technician for
help.
This device complies with the Industry Canada Radio Standards Specification
RSS 21 0. Its use is authorized only on a no-interference, no-protection basis; in
other words, this device must not be used if it is determined that it causes harmful interference to services authorized by IC. In addition, the user of this device
must accept any radio interference that may be received, even if this interference
could affect the operation of the device .
Warning:
Changes or modifications not expressly approved by the party re-
sponsible for compliance could void the user's authority to operate this device.
2
© 2011 Directed Electronics. All rights reserved.
A Warning! Safety first
The following safety warnings must be observed at all times:
Due to the complexity of this system, installation of this product must only be
performed by an authorized Directed dealer.
When properly installed, this system can start the vehicle via a command signal
from the remote control transmitter. Therefore, never operate the system in an
enclosed area or partially enclosed area without ventilation (such as a garage) .
When parking in an enclosed or partially enclosed area or when having the
vehicle serviced, the remote start system must be disabled using the installed
toggle switch. It is the user's sole responsibility to properly handle and keep out
of reach from children all remote control transmitters to assure that the system
does not unintentionally remote start the vehicle. THE USER MUST INSTALL A
CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING
AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE
AREA MUST AT ALL TIMES REMAIN CLOSED . These precautions are the sole
responsibility of the user.
Use of this product in a manner contrary to its intended mode of operation may
result in property damage, personal injury, or death. ( 1) Never remotely start the
vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with
the keys in the ignition. The user must also have the neutral safety feature of the
vehicle periodically checked, wherein the vehicle must not remotely start while
the car is in gear. This testing should be performed by an authorized Directed
dealer in accordance with the Safety Check outlined in the product installation
guide. If the vehicle starts in gear, cease remote start operation immediately and
consult with the authorized Directed dealer to fix the problem.
After the remote start module has been installed, contact your authorized dealer
© 2011 Directed Electronics. All rights reserved.
3
to have him or her test the remote start module by performing the Safety Check
outlined in the product installation guide. If the vehicle starts when performing
the Neutral Safety Shutdown Circuit test, the remote start unit has not been
properly installed. The remote start module must be removed or the installer must
properly reinstall the remote start system so that the vehicle does not start in gear.
All installations must be performed by an authorized Directed dealer.
OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN
GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT
IN PROPERTY DAMAGE OR PERSONAL INJURY. YOU MUST IMMEDIATELY
CEASE THE USE OF THE UNIT AND SEEK THE ASSISTANCE OF AN AUTHORIZED Directed DEALER TO REPAIR OR DISCONNECT THE INSTALLED
REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR
PAY FOR INSTALLATION OR REINSTALLATION COSTS.
This product is designed for fuel injected, automatic transmission vehicles only. Use of this product in a standard transmission vehicle is
dangerous and contrary the product's intended use.
4
© 2011 Directed Electronics. All rights reserved.
What is Included
•
•
The control module
Two 1-button transmitters
•
•
A push-button programming switch
Your warranty card
•
A shut-down toggle switch
(P /N 721 1V)
Important Information
Congratulations on the purchase of your remote start keyless entry system. This system has been designed to provide years of trouble-free
operation. By carefully reading this owner's guide prior to using your
system, you can maximize the use of this system and its features. Additional or replacement copies of this guide can be printed by accessing
the Directed Electronics internet website at www.directed.com.
Your Warranty
Your warranty card must be completely filled out and returned within
10 days of purchase. Your product warranty is not honored if your
warranty card is not returned. Make sure that you receive the warranty
card from your dealer.
System Maintenance
The system requires no specific maintenance. Your remote is powered
by two CR20 16 cell batteries. When the batteries weakens, the LED
on the remote dims and operating range is reduced.
© 2011 Directed Electronics. All rights reserved.
5
BaHery Replacement
Front
1.
Using a small slotted screwdriver, insert into slot located on
the side of the unit as shown and
carefully pry the front of the unit up,
working your way around the edge
until the front is completely separat-
Elastomer
contact
ed from the housing.
Circuit Board
Note:
Make sure that the small elastomer contact located inside the unit as
shown does not fall out during the replacement process.
Turn the circuit board over, remove batteries from clip and replace.
2.
Note:
Verify that the battery polarity is correct when replacing. Batteries are stacked in series and polarity is indicated.
3.
6
Reposition all parts and snap together.
© 2011 Directed Electronics. All rights reserved.
Using Your System
Unlocking
Only after the vehicle is remotely started via the transmitter, press and
release the transmitter button for 1 second to unlock the vehicle's doors.
The remote responds with 2 short beeps and the green LED on the remote flashes once. The vehicle responds by flashing the parking lights
twice and honking the horn twice to confirm unlocking.
Note:
horn honk is an optional feature.
Cor Finder
Before the vehicle is remotely started via the transmitter, press and
hold the transmitter button for 3 seconds to activate the car finder
function. The vehicle responds by flashing the parking lights 5 times
slowly. The remote responds with 1 short beep and the orange LED on
the remote flashes once.
Ignition Controlled Door Locks
If power door locks have been
DRW-94
LOCK
connected to your system, the doors
wi II lock three seconds after the
ignition is turned on, and unlock
when the ignition is turned off.
UNLOCK
~
I
© 2011 Directed Electronics. All rights reserved.
7
Note: In order for the ignition controlled door locks to work, the feature
must be turned on in programming.
Note: If the ignition is turned on while the vehicle is remote started the
doors do not lock until the remote start shuts off. To avoid being locked
out of the vehicle, do not turn the ignition on until you are ready to drive
the vehicle.
Remote Start
This feature allows you to remotely start and run your vehicle for a
programmab le period of time. This makes it possible to warm up the
engine, as well as adjust the interior temperature of the vehicle with
the climate control system. If interior heating or cooling is desired, the
climate controls must be preset, and the fan blower must be set to the
desired level prior to remote starting the vehicle.
lmportantl (l) Never remotely start the vehicle with the
vehicle in gear, and (2) Never remotely start the vehicle
with the key in the ignition.
;,,,,,,,,,,,,_,,,,,,. , .
. .... ,., ..
' ·'
....
'
.,. ,.
--
,,
....., ....• ,.............., . " ·" ' '"
""" '
... ,..,..
, ,,,, .• ,
.. ,., ..., . .,
,., . , ....,.
,., ' ''"""·
..... .,.. , ................ , ,.. .,,
To remote start the vehicle:
l . Press the single button on the transmitter once.
2.
3.
The remote responds with the remote start On tones and the green
LED on the remote flashes once. The vehicle's parking lights turn
ON constant to confirm remote start operation.
Once the vehicle has started, it runs for the pre-programmed period of time ( 12, 24, or 60 minutes) or until a shutdown input is
triggered. This can be set to minute increments by your installer.
To shut off the remote start:
While the vehicle is remote started press and hold the button on the
8
© 2011 Directed Electronics. All rights reserved.
remote for 3 seconds . The remote plays the remote start shut off tones
and the orange LED flashes 1 time. The vehicle shuts down from the
remote start mode.
2.
Press the brake pedal. The vehicle stays running
and is ready to drive.
Note:
If the brake pedal is pressed before the key is in the ON position,
the engine shuts down.
While the vehicle is running during remote start operation, the system
monitors the vehicle and automatically shuts down the engine if the
system receives any of the following shut-down inputs:
•
The brake pedal is pressed.
•
The hood is opened.
•
The shutdown toggle switch is put into the ON position.
The pre-programmed run time has elapsed.
The single button is pressed and held for 3 seconds.
•
•
© 2011 Directed Electronics. All rights reserved.
9
Valet Take-Over
The Valet Take-Over feature allows the vehicle to remain running
after the key has been removed from the ignition. This feature is
useful for occasions when you wish to exit and lock the vehicle for
short periods of time, but would like to leave the motor running
and the climate controls on.
To perform Valet Take-Over:
1.
Before turning off the engine, press and release the single button
once. The remote responds with the remote start ON tones and the
green LED on the remote flashes once. The vehicles parking lights
turn on constant to confirm remote start operation.
2.
Turn the ignition key to the OFF position.
(The engine stays running.)
3.
The engine runs until pre-programmed time elapses or a shut-down input is received. (See the previous Remote Start
section for a complete list of shut-down inputs.)
Note: This feature does not work if the brake pedal is being pressed.
10
© 2011 Directed Electronics. All rights reserved.
Prog£omming options
Programming options control your system's normal operational set-up.
Most options do not require additional parts, but some may require
installation labor.
The following is a list of the programmable options, with the factory
settings in bold.
•
12,
24, or 60 minute run time. Your system can be programmed
to allow the vehicle to run for 12, 24, or 60 minutes when remote started. Can be set up to minute increments by your installer.
•
Parking lights flashing or constant. Your system can be programmed
to turn on the parking lights for the entire remote start operation.
Glosso£y of le£ms
Control Unit: The "brain" of your system. Usually hidden underneath
the dash area of the vehicle. It houses the microprocessor which monitors your vehicle and controls all the system functions.
Transmitter: A hand-held, remote control which operates the various
functions of your system.
© 2011 Directed Electronics. All rights reserved.
11
~ Quick Reference Guide
To remote start the vehicle
•
Press and release the transmitter button for 1-second. The remote responds with the remote start ON tones and the green
~
LED on the remote flashes once. The parking lights turn on
~
~I
constant to confirm remote start operation.
~
To shut down remote start
•
Press and hold the transmitter button for 3 seconds. The remote
will play the remote start shut off tones and the orange LED will
flash l time The parking lights will turn off.
Car finder (remote start must not be active)
•
Press and hold the transmitter button for 3-seconds. The remote
will respond with l short beep and the orange LED on the
remote will flash once. The parking lights will start to flash 5
times slowly.
To unlock the doors (remote start must be active)
§I
•
(1)
c:
Press and release the transmitter button for l second. The remote will respond with 2 short beeps and the green LED on the
remote will flash once, the horn will honk twice and the doors
will unlock.
I
X
© 2011 Directed Electronics. All rights reserved.
13
Limited lifetime consumer wo[[ooty
Directed Electronics. ("Directed") promises to the original purchaser to repair or replace (at
Directed's election) with a comparable reconditioned model any Directed unit (hereafter
the "unit"), excluding without limitation the siren, the remote transmitters, the associated
sensors and accessories, which proves to be defective in workmanship or material under
reasonable use during the lifetime of the vehicle provided the following conditions are met:
the unit was purchased from an authorized Directed dealer, the unit was professionally
installed and serviced by an authorized Directed dealer; the unit will be professionally
reinstalled in the vehicle in which it was originally installed by an authorized Directed
dealer; and the unit is returned to Directed, shipping prepaid with a legible copy of the
bill of sale or other dated proof of purchase bearing the following information: consumer's
name, telephone number and address; the authorized dealers name, telephone number
and address; complete product description, including accessories; the year, make and
model of the vehicle; vehicle license number and vehicle identification number. All components other than the unit, including without limitation the siren, the remote transmitters
and the associated sensors and accessories, carry a one-year warranty from the date of
purchase of the same. ALL PRODUCTS RECEIVED BY DIRECTED FOR WARRANTY REPAIR
WITHOUT PROOF OF PURCHASE WILL BE DENIED. This warranty is non-transferable
and is automatically void if: the original purchaser has not completed the warranty card
and mailed it within ten (10) days from the date of purchase to the address listed on the
card; the unit's date code or serial number is defaced, missing or altered; the unit has been
modified or used in a manner contrary to its intended purpose; the unit has been damaged
by accident, unreasonable use, neglect, improper service, installation or other causes not
arising out of defects in materials or construction. The warranty does not cover damage
to the unit caused by installation or removal of the unit. Directed, in its sole discretion, will
determine what constitutes excessive damage and may refuse the return of any unit with
excessive damage.
TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING
BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NONINFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED; AND
DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME
FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS.
DIRECTED DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS
OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS. DIRECTED
SECURITY SYSTEMS, INCLUDING THIS UNIT, ARE DETERRENTS AGAINST POSSIBLE
THEFT. DIRECTED IS NOT OFFERING A GUARANTEE OR INSURANCE AGAINST
VANDALISM, DAMAGE OR THEFT OF THE AUTOMOBILE, ITS PARTS OR CONTENTS;
AND HEREBY EXPRESSLY DISCLAIMS ANY LIABILITY WHATSOEVER, INCLUDING
© 2011 Directed Electronics. All rights reserved.
15
WITHOUT LIMITATION, LIABILITY FOR THEFT, DAMAGE AND/OR VANDALISM. THIS
WARRANTY DOES NOT COVER LABOR COSTS FOR MAINTENANCE, REMOVAL OR
REINSTALLATION OF THE UNIT OR ANY CONSEQUENTIAL DAMAGES OF ANY KIND .
IN THE EVENT OF A CLAIM OR A DISPUTE INVOLVING DIRECTED OR ITS SUBSIDIARY,
THE VENUE SHALL BE SAN DIEGO COUNTY IN THE STATE OF CALIFORNIA.
CALIFORNIA STATE LAWS AND APPLICABLE FEDERAL LAWS SHALL APPLY AND GOVERN
THE DISPUTE. THE MAXIMUM RECOVERY UNDER ANY CLAIM AGAINST DIRECTED
SHALL BE STRICTLY LIMITED TO THE AUTHORIZED DIRECTED DEALER'S PURCHASE
PRICE OF THE UNIT. DIRECTED SHALL NOT BE RESPONSIBLE FOR ANY DAMAGES
WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES,
INCIDENTAL DAMAGES, DAMAGE TO VEHICLE, DAMAGES FOR THE LOSS OF TIME,
LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY
AND THE LIKE . NOTWITHSTANDING THE ABOVE, THE MANUFACTURER DOES OFFER
A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE SUBJECT TO
THE CONDITIONS AS DESCRIBED HEREIN . THIS WARRANTY IS VOID IF THE UNIT
HAS NOT BEEN PURCHASED FROM DIRECTED, OR AN AUTHORIZED DIRECTED
DEALER, OR IF THE UNIT HAS BEEN DAMAGED BY ACCIDENT, UNREASONABLE USE,
NEGLIGENCE, ACTS OF GOD, NEGLECT, IMPROPER SERVICE, OR OTHER CAUSES
NOT ARISING OUT OF DEFECT IN MATERIALS OR CONSTRUCTION.
Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific
legal rights and you may also have other rights that vary from State to State.
This warranty is only valid for sale of product(s) within the United States of America.
Product(s) sold outside of the United States of America are sold "AS-IS" and shall have NO
WARRANTY, express or implied. This product may be covered by a Guaranteed Protection
Plan ("GPP") . See your authorized Directed dealer for details of the plan or call Directed
Customer Service at 1-800-876-0800.
Make sure you have all of the following information from your authorized Directed
dealer:
A clear copy of the sales receipt, showing the following :
Date of purchase
o
Your full name and address
o
Authorized dealer's company name and address
0
Type of alarm installed
0
Year, make, model and color of the automobile
0
Automobile license number
0
Vehicle identification number
0
All security options installed on automobile
0
Installation receipts
0
920-0003 06-06
16
© 2011 Directed Electronics. All rights reserved.
driven to excel
Z'~ard·
The company behind Viper® Auto Security
E L E C T R 0 N I C S
Systems is Directed Electronics.
Vista, CA 92081
www.viper.com
Since its inception, Directed Electronics has
had one purpose, to provide consumers with
the finest vehicle security and car stereo products and accessories available. The recipient
of nearly 100 patents and Innovations Awards
in the field of advanced electronic technology,
Directed Electronics is ISO 9001 registered.
Quality Directed Electronics products are sold
and serviced throughout North America and
around the world.
Call (800) 876-0800 for more information
about our products and services.
© 2011 Directed Electronics. All rights reserved.
Directed Electronics is an
ISO 9001 registered company.
G4203V 2011 -05
ions________________________ _
Quick Reference Install Guide
or a Spanish version of the Insta llation Guide, please down load it from
irectechs.com under Resources.
Remote Start with Keyless Entry
4203-series
1-button remote- 2-way
i buscas los guios de instalaci6n , por favor de bo jor lo del Resources en el sitio
direclechs.com
Wiring Connections
Installation Points
ResetamlDelelion__
Iodllearning_ _ _______ _
If a feature/virtua l tach needs to be reset or the remote con trols need to
use the following procedu re
W'WW
To learn the tach signal:
1
Sta rt the vehicle w ith the key.
2.
With in 5 seconds, press a nd hold the Valet !Control) button.
Aher 3 seconds the system LED w ill light constant when the tach signal is
3.
lea rned
4
Release the Valet IConlrol) bullon
Turn the ign ition to the ON position [The heavy gauge p ink w ire must be connected) .
Within 10 seconds, press and release the Va let button: 2 li mes if you want to
delete remotes, 3 times to reset features or 4 times to reset virtual tach. These
feature:; are described next
Gouge Reloy, 6-pin connector
PINK
OUTPUT TO PRIMARY IGNITION CIRCUIT
PURPLE
OUTPUT TO STARTER CIRCUIT
ORANGE
OUTPUT TO ACCESSORY CIRCUIT
REO
(+) (30A) HIGH CURRENT 12V INPUT
PINK/WHITE
OUTPUT TO SECOND IGNITION/ACCESSORYCIRCUIT
REO
(+) (30A) HIGH CURRENT lZV INPUT
Delete remotes: This fea ture erases a ll remotes from the memory of the
system . This is usefu l in cases when a customer's remote is lost o r stolen.
Note : This does not reset the prog rammed features o f the system or reset
the Virtual Tach setting.
Important: This unit can learn the tachometer with the analog input or
through D2D using on interface modu le. The unit confirms which source
is used by flash ing the parking lights.
When programming tach learning with:
Analog, the parking lights flmh one lime
020 interface module, the pa rking lights fl ash twice
Reset Features: This resets all features of the system to the fa ctory default
settings.
Note: Th is feature does not delete the remotes from the system or reset
the Virtua l Tach setting
If the tachometer input on the system is connected to the veh icle, the D2D tachometer
input w ill be ignored.
Satellite harness -4-pin connector
BLUE
(-) 200mA STATUS OUTPUT
ORANGE
(-) 200m A ACCESSORY OUTPUT
PURPLE
(-) 200m A STARTER OUTPUT
PINK
(-) 200mA IGNITION OUTPUT
Virtual Tach Reset; Deletes all p reviously learned values lor Virtual Tach,
and on the next remote start sequence the unit begi ns virtual tach in itialization .
Virtual loch
Note: The "Zapn feature on the Bitwriter does not reset the Virtua l tach
setting .
Note: Virtual toch is not recommended for diesel vehicles.
Door Lock, 3-pin connector
(-) UNLOCK OUTPUT
To program Virtual Tach :
1
After the insta ll is complete, remote start the car.
3.
2.
3.
4.
4.
NOT USED
If the car does not start o n the firs t attempt, let the remote start attempt again.
Once the car starts, let it run unti l the parking lights come o n.
W hen the parking lights come on, shut off the remote start w ith the remote that's it! Virtual Tach is programmed.
(-) LOCK OUTPUT
Virtual Tach hand les disengagi ng the starter motor d uring remote starting- it does
not address over-rev. If the customer wants to have the over-rev protection capobil·
ity, the tach wire must be connected. Th is may involve more installation shop
charges than ini tial ly quoted
Important: If the Virtual Tach mode over cranks or doesn 't crank the
vehicle long enough to start and run the cor, use the Bitwriter to odd or
subtract the starter output time. You can adju::.t the output ti me in increments of 50msec of the learned time using the Bitwriter.
The Red 4-pin plug may be config ured as a Bitwriter/ESP2 o r D2D port
The factory default is Bitwriter/ESP2 mode
Antenna
Side View
J
Heavy
Gauge
Relay
Satellite Harness
Primary Harness
Remote Start Harness
To use os 020 mode Follow the below steps:
LED (Programming
indicator)
Control Button
(Valet Switch)
Door Lock/unlock
Harness
Antenna
1
2
3.
Make sure Wh ite/Blue activation wire is g rounded.
Power the unit up. The system lED flashes for 5 seconds to confirm D2D mode
change
Remove the White/Blue w ire from ground
Remote Start Slrutdown.lliognost....,
· '-------2
3
4.
Turn the ignition On and then bock O ff while holding the Valet button.
Release the Va let button
Press and release the Valet button. The lED fla::.hes to report the last
shutdown lor one minute or until the ignition is turned on , as shown in the
following table:
LEDFiosh"'
I flash
2 flashes
3 flashes
4 flashes
5 flashes
6flashes
7flashes
8 flashes
Shutdown Mode
Timed out
Over-rev shutdow n
low o r no RPM, low battery (voltage and virtual tach modes)
Transmitter shutdown (or optional push button)
1-1 Hood Shutdown IH3/4 GRAY)
1+1 Shutdown IH3/3 BROWN)
1-1 Neutcol safety shutdown IH3/ I BLACK/WHITE)
Wait-to-start ti med out
To change from D2D to Bitwriter/ ESP2 mode:
1.
Make sure Wh ite/Blue activation wire is grounded
2.
Power the un it up, the system LED turns on solid for 5 seconds to confirm Bitw riter/ESP2 mode change
Remove the White/Blue w ire from ground.
The procedure can
be repeated
Bitwriiers wi th a date code of 6o or older require on IC
upgrade (p/n 998MI. Some bitwriters wi th a dote code
of 6B do not require the IC upgrade, refer to tech ti p #
11 12 lor more inlormoli·:m
to togg le from one mode to the other
Important: If you power up the system with the Wh ite/Blue activation
wire ungrounded, the system LED wil l come on solid for 5 seconds indicating the system is in Bitwriter/ESP2 mode.
© 201 1 Directed Electronics. All rights Reserved
Once you have selected the function step, press the Valet button once more
and hold it. The LED flashes and the horn hon ks to confirm the selected functional step. Do not release the Valet button.
Wh ile holding the Valet button, pre::.s the button on the remote control. The
horn honks to confi rm that the fea ture has been ::.uccessfully reset. You can now
release the Valet button.
To perform shutdown diagnostics:
With the ignition Off, press and hold the Valet button.
1
Red 4-pin port, Bitwriter/ESP2 or 020 programming
Side View
be deleted,
I
I' .
..--.--:::a •
The Bitwriter® (p/n 998UI
requires chip version 2.7 or
newer to program this unit
Feature Menus
PllllJIOmming System Features
The System Features learn Routine dictates how the unit operates It is
featu re settings using the Va let button.
1
2.
possible
to access and change most of the
Turn the ig ni tion on, then off.
Select o Menu . W ithin 10 seconds, Press and hold the Va let button. The number of LED flashes and horn
honks indicates the menu number. A single LED flash and honk indicates menu 1 Two LED flashes and 2
1.
Menu 1
3.
2
Feaiure I
honks ind icates menu 2.
When the desired menu LED flashes and honks are heard, release the Valet bulion
4
5.
Remote Programming
Default settings are in bold type.
Feature
Opt. 1
Opt. 2
Opt. 3
Opt.4
Opt. 5+
Ho rn function
Off
Si ren
Siren
Siren
Siren
Select a Feature, within 10 seconds. Press and release the Valet button the number of times correspond-
20 mS
ing to the feature you wish to change . Then press and hold one more ti me to select the feature. The LE D
flashes and the horn honks to indicate which feature is selected.
Program the Featu re. While holding the Valet button, you can progra m the fea ture using the remote
control
Off
Ignition con-
To access another feature in the same menu :
1 Press and release the Va let button the number of times neceswry to advance from the feature you just programmed to the next o ne you wont to program.
2. Then press the Va let button once more and hold it
To select another menu:
1
Press and hold the Valet button
2. After 3 seconds, the unit advances to the next menu, the horn honks and LED flashes indicating which menu
has been accessed.
The learn routine exits if any of the f~lowing occurs:
The ignition is turned On
There is no activity for 30 seconds
The Valet button is p ressed too many times
On
trolled un lock
Pressing the button on the remote control advances to each fea ture option . The LED fla shes and the horn honks
indicating which option is selected.
Once o feature is programmed:
Other features con be prog ra mmed within the some menu
Another menu con be selected
The lea rn routine con be exited if programm ing is complete
30 mS
mS
-- - -40 - - -50-mS-.
Doorlock output duration
0:8 sec,
3.5 sec.
~~~le
Off
On
pu lse
4.
5.
6
7.
Turn key to the ON position
With in 10 seconds, press and release Valet button one time
Within 10 seconds, press and hold the Valet button. The LED w ill flas h one time and the horn hon ks (if connected) to confirm entry into remote programming
Press the button on the remote contro l
The horn honks to con fi rm the remote has been programmed .
Release the Valet button, and turn the key to the Off position .
The horn sounds one long honk to confirm that remote p rogramming has been exited
The programming routine exits if ony of the following occurs:
The ign ition is turned off
There is no activity for 30 seconds
The Va let button is pressed too many times
OAsec .
f-----Double pu lse ---,-:;-----,-------;-----,-On
Off
lock
Factory Alarm
Disarm function
'-·~·
with unlock
Before unlock
Factory Ala rm
~i-7~-,....-',-Disorm
Pulses
Comfort *
C losure
f·
t
Panic*
qn
~'-'''-'·':..,<:.....~~.-
·Option not available on 1-button remote
Menu2
Bilwriter -Only Options
II
If program ming w ith the _Bilwriter®, the learn routi ne can be locked or unlocked . If the learn routi ne has
previously been locked, 11 must be unlocked w ith Bitwriter® - this cannot be done man ually w ith the Va let
button.
II
The Bitwriter®
gives you access too w ider ra nge of system options. These additional features and the ad justments that may be programmed are described in the table below.
latch rear
defogger
Pulse f~r · · :
defogger
Off
Timed
1'2 -min ..
•Option not available on 1-button remote
3 min
15 sec
Time'd 30 sec.
Timed
6 min
9 min
45
sec
See full Installatio n Gu ide for more
detailed information on this system .
Such information and more can be
found online at·
www.directechs.com
E L E C T R 0
N I C S
QRN~Ol lOI I ·I I
©
201 1 Directed Electron ics. All rights Reserved
LAD42032
VEHICLE EQUIPPED WITH A DEl® REMOTE START SYSTEM
If vehicle battery is disconnected, the system may attempt to start when the battery is reconnected or transmitter
is used. Press brake to disengage. Check with vehicle owner to determine if hood pin switch or override switch
was installed to disengage the system for service.
IMPORTANT SAFETY NOTICE
Please send products and other
correspondence to:
First-Class
Postage
Required
Post Office will
not deliver
without proper
postage.
Directed
1 Viper Way
Vista, CA 92081
XFR01-01
DIRECTED®
PO BOX 174391
DENVER CO 80217-4391
11 .. 1.11 ••••• 1.1 ••• 111 ••• 1.1 .. 1•• 11.1.1 ••••• 111.1 ..... 11.1.1.1
DIRECTED®
PRODUCT REGISTRATION
Protect Your lnrestment
Regist~r your product
now
to receive these benefits:
-----
~ Owner Verification
Proof of purchase in case of product theft or loss
~ Efficient Warranty Service
In case there is a problem with your product
Or register online at www.prodregister.com/directed
IMPORTANT!
D I RE CTE D
®
1.
IMPORTANT!
Please complete and return within the next 10 days
or register online at productregister.com/directed.
XF RO 1
1. 0 Mr.
2. 0 Mrs.
3. 0 Ms.
First Name
4. 0 Miss
Initial
Last Name
Apt.
Street
City
State/Province
Zip/Postal code
E-mail address
2.
I
Your date of birth:
Month
3.
Marital status:
4.
Date of purchase:
01. 0
11.
How did you first become aware of this product? (check one)
01. 0 Local newspaper
07. 0 Radio commercial
02. 0 Yellow pages
08. 0 Salesperson's
03. 0 Magazine Ad
recommendation
04. 0 TV commercial
09. 0 Motorsports
05. 0 Magazine article/
sponsorship
review
10. 0 Internet
06. 0 Friend/Relative's
11. 0 Other
recommendation
12.
What factors most influenced the purchase? (check up to three)
01. 0 Directed's reputation
09. 0 Rebate/Promotion
02. 0 Experience with
10. 0 Style/Design/Color
Directed products
11. 0 Dealer proximity
03. 0 Experience with dealer 12. 0 Friend's
04. 0 Value/Price
recommendation
05. 0 Special features
13. 0 Salesperson
06. 0 Warranty
recommendation
07. 0 Quality/Durability
14. 0 Compatibility w/vehicle
08. 0 Display in-store demo 15. 0 Other
Year
Married
02. 0
I
Month
5.
Model number:
6.
Name of store where purchased:
Single
I
Day
Year
7. Price paid:
(excluding tax)
8.
9.
10.
Which Directed brand did you purchase?
01. 0 Autostart
04. 0 Python
02. 0 Avital
05 0 Vyper
03. 0 Clifford
06 0 Other
13. What benefits most influenced your decision to purchase
this product? (check up to three)
01. 0 Improved security
02. 0 Improved convenience
03. 0 Improved performance
04. 0 Compatibility w/vehicle
05. 0 Ease of installation
06. 0 Style/Design/Color
07. 0 Special features
08. 0 Quality/Durabi Iity
09. 0 Increase vehicle value
10. 0 Functionality
What type of product did you purchase?
01. 0 Security system
02. 0 Security system with remote start
03. D Remote start system
04. 0 Keyless entry system
In what vehicle will this product be used?
01. 0 Car
04. 0 Van
07. 0
02. 0 Truck
05. 0 Minivan
08. 0
03. 0 suv
06. 0 Motorcycle 09. 0
Boat
Motorhome
Other
14.
Make of vehicle:
Model name:
YIN:
Year:
01. 0
02. 0
Boughtnew 03. 0
Bought used 04. 0
11.
12.
13.
14.
0
0
0
0
15. 0
16. 0
17. 0
Warranty
PriceNalue
Rebate/Promotion
Immediate
availability
Friend/Family's
recommendation
Salesperson's
recommendation
Dealer proximity
What other brands did you seriously consider before
making this purchase?
01. 0 No other brands
06. 0 Compustar
07. 0 Prestige
considered
08. 0 Pursuit
02. 0 Other Directed brands
03. 0 Code Alarm
09. 0 Crime Stopper
10. 0 Bulldog
04. 0 Audiovox
05. 0 Auto Page
Leased new
Leased used
Failure to return this form will not change your warranty rights.
Copyright C 2012 All Rights Reserved - Please seal with tape. Do not staple. 540-0070 (B)
LRDEI007
This product is
303,223
340,000
3.52,685
4,38),2~1.
4,8-1,63G
5, ltJ, 141
5,534,845
5,798,711
5,952,933
cC>,ie.rE~d
by one or more of the following U.S. patents:
;333,6.33
344,905
383,689
4,438,41.B
4,922,1-4
5,245,8'4
5,572,.1:85
.5,872,519
5,990,786
333,634
34.5,11.?
383,690
4.,.i$3, 127
~.987,402
5,285,186
5,6461591
5,90CI,806
6,093,979
333,635
345,711
390,830
4,584,569
5, I03,221
5,31.5,285
5,656,997
5,907,195
333,636
347,190
392,944
4,794,368
5, 1<17.,217
5,857,560
5;1'12,638
5,914,667
333,795
348,622
4,327,444
4,887,064
5,132,660
5,532,670
5,783,989
5,945,936
International Patents:
Australia:
Canada:
Taiwan:
694,925
I,315,859 and 2,067,099
91817
Other patents pending
MKG-1