USERS INFORMATION MANUAL
Heating & Cooling Systems
MODEL TSTATBBNB001
PROGRAMMABLE DIGITAL
THERMOSTAT
NON-PROGRAMMABLE DIGITAL
THERMOSTAT
72 72
AUTO
COOL
74
HEAT
Dual Setpoint
Thermoglow Backlight
No Batteries Required
Auto Changeover
Locking Keypad
Meets California Title 24 Residential
Heat Pump & Heat Cool
Table Of Contents
FRONT PANEL
DISPLAY
BASIC OPERATION
ADVANCED SETUP
ABOUT ADVANCED OPERATION
WARRANTY
2
3
4
6
10
13
CAUTION
Follow Installation Instructions before proceeding.
SET THERMOSTAT TO MODE “OFF” PRIOR TO
CHANGING SETTINGS IN SETUP OR RESTORING
FACTORY DEFAULTS.
Residential Light Commercial Systems
Carrier Corporation 04/01
TSTATBBNB001
Page 1
Front Panel
1
72 72
AUTO
3
COOL
74
HEAT
4
5
1
Liquid Crystal Display
2
Up/Down Buttons
3
Mode Button
4
Fan Button
5
Heat or Cool Indicator
with Thermoglow
Heat = Red, Cool = Green
Page 2
2
Display
1
2
1
88 88
AUTO
OFF
COOL
88
1
HEAT
1
3
3
Fan On
4
1
Mode Indicators
Selects the operation mode of the equipment.
HEAT - indicates the heat mode.
COOL - indicates the air conditioning mode.
AUTO - indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
OFF - indicates the entire system is turned off.
Page 6.
2
Room Temperature Display
Indicates the current room temperature.
3
Desired Set Temperature
Indicates desired room temperature(s). Page 7.
4
Fan Operation Indication
Fan On - indicates constant, continuous fan
operation.
When Fan On is not lit - indicates the fan will
only operate when necessary to heat or
to cool. Page 7.
Page 3
Basic Operation
Select Mode
The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
72 74
72
72
74
72 72
72
HEAT
MODE
COOL
The COOL setting indicates the
temperature the room has to
reach before the air conditioner
will turn on to cool the room.
AUTO
AUTO will automatically select
heat or cool based on room
temperature demand.
OFF indicates both heating
and air conditioning
systems are turned off.
COOL
MODE
HEAT
OFF
Page 4
MODE
Basic Operation
Select Desired Temperature
72 72
AUTO
COOL
74
In any mode, adjust the
desired Set Temperature
with
HEAT
buttons.
Pressing the Up or Down buttons in Auto mode will adjust both the heat and cool
set temperatures simultaneously.
Pressing the Up or Down buttons in Heat or Cool modes will adjust only the
heat or cool set temperature.
Fan
Operation
Press
FAN
72 72
AUTO
COOL
74
Fan On indicates constant fan operation.
This feature is active even if the thermostat
is set to Off.
HEAT
Fan On
Page 5
Advanced Setup
Press the Mode button.
While holding the Mode,
press the Fan button
for 5 seconds to enter Setup
screens.
MODE
FAN
NOTE: Each step # is located at
the top right corner of the
display for easy reference.
2 85
2
2
Select 2 for dual setpoint
1 for single setpoint.
1
Press
MODE
4
On
Select residential Heat Pump,
ON or OFF.
Off
hp
OFF
Press
MODE
0
B
Select the reversing
valve polarity for
Heat Pump, O or B.
(Step 5 only appears if
heat pump is on in step 4)
O
5
Press
MODE
Continued
Page 6
Advanced Setup
6
Select Electric Heat On
or Off. (Step 6 only
appears if heat pump is
off in step 4)
OFF
eh
2
8
2
9
6 cy
Press
MODE
7
Adjust the deadband
from 1 - 6 degrees.
88
Press
MODE
COOL
Adjust the minimum
difference between
cooling & heating
setpoints.
HEAT
8f
(0 - 6 )
Select the cycles per
hour limit.
d=cycles per hour
limit defeated.
d1=d + defeat 5 min.
Compressor lockout.
(d, d1, 2 - 6)
Press
MODE
Press
MODE
Continued
Page 7
Advanced Setup
i0
On
Select the display backlight always On, or Off
after 8 seconds.
HEAT
Off
On
li
Press
MODE
f
C
Select thermostat
operation in degrees
Fahrenheit or Centigrade.
ii
F
Press
MODE
FAN
Press the Mode button.
While holding the Mode, press the Fan
button for 2 seconds to leave the Setup
screens. If no buttons are pressed, the
display will leave the setup screens after
30 seconds.
Page 8
Advanced Setup
Advanced Setup Table
Step #
2
4
5
6
7
8
9
10
11
Description
Range
Display Type Dual (2) or Single (1)
Heat Pump
Reversing Valve polarity
Electric Heat
Deadband or Temperature swing
Forced minimum difference heat/cool
Cycles per hour
Thermoglow backlight
Fahrenheit or Centigrade
Page 9
1-2
Off / On
O/B
Off / On
1-6
0-6
d, d1, 2 - 6
Off / On
F/C
Factory Default
2
Off
O
Off
2
2
6
On
F
About Advanced Features & Operation
2 STAGE OPERATION - The 2nd Stage of heat or cool is
turned on when (1) the 1st Stage has been on for a
minimum of two minutes, and (2) the temperature spread
from the setpoint is equal to or greater than: the setpoint
plus the deadband, plus 2 degrees.
Cooling
Heating
2 degrees
2nd Stage
turn on
1st Stage
turn on
Dead
Band
Heat
Setpoint
Dead
Band
Cool
Setpoint
2 degrees
1st Stage
turn on
2nd Stage
turn on
MINIMUM HEAT/COOL SETPOINT DIFFERENCE - The Heat
and Cool setpoints will not be allowed to come any closer
to each other than the value set in Advanced Setup step
# 8, on page 7. This minimum difference is enforced
during Auto changeover and Program On operation.
EMERGENCY HEAT - Is a feature available to Heat Pump
installations. To turn on Emergency Heat press in the
Fan button. While holding the Fan button press
the Up button for 2 seconds. The Cool setpoint display
will read ‘EH’.
Press for
Emergency Heat
72 72
EH
HEAT
Fan
During Emergency Heat the thermostat will turn
on the fan and the 2nd stage of heat, when there is a
demand for heat, locking out the 1st stage compressor.
Exiting Emergency Heat is the same as entering. During
Emergency Heat only OFF and HEAT are available.
Page 10
About Advanced Features & Operation
ELECTRIC HEAT - Selecting Electric Heat on, page 7,
step 6, will cause the thermostat to turn on the fan
immediately any time there is a heat demand. Since all
gas furnaces control the fan, this feature should be off
unless the heater is only electric.
KEYPAD LOCK - To prevent unauthorized use of the thermostat,
the front panel buttons may be disabled. To disable, or
‘lock’ the keypad, press and hold in the Mode button.
While holding the Mode button in, press the Up and Down
buttons in together.
72 72
AUTO
Press all 3 for
Keypad Lockout
COOL
74
HEAT
MODE
To unlock the buttons, again press and hold the Mode
button. While holding the Mode button in, press the Up
and Down buttons in together.
Page 11
About Advanced Features & Operation
DUAL SETPOINT BEHAVIOR - The adjustable setpoint range
is: 35 - 99 degrees in Fahrenheit and 7 - 35 degrees in
Centigrade. When in the modes Heat or Cool, this
adjustable range is unhampered.
When adjusting any Auto mode, including programming
Occupied and Unoccupied periods, the 1050 will not
allow the Heat setpoint to get closer to the Cool setpoint
than the value programmed as the minimum difference in
step 7, page 13.
When entering the Auto mode from Cool, the Heat and
Cool setpoints will remain spread apart by the amount
that they were adjusted, prior to entering Auto.
For example: If the Cool setpoint was set to 80 while
in the Cool mode and the Heat setpoint was adjusted to
70 while in the Heat mode, upon entering the Auto mode
the Heat and Cool setpoints would be 80 and 70. Both
setpoints would then move up and down together, (in this
example spread by 10 degrees), by pressing the up or
down buttons.
To move the Heat and Cool setpoints closer together,
enter the Cool or Heat mode by pressing the Mode button,
then adjust the setpoint(s) closer together. Heat is limited
to how close it can come to Cool by step 7, page 13.
FACTORY DEFAULTS - If, for any reason it is desirable to
return all stored settings back to the factory default
settings, press the Mode button. While holding the Mode
button in, press the Down button for 5 sec. All icons will
appear. Press and hold in the Fan button until Fd
appears. This resets all factory settings. To calibrate
room temperature, press the Mode button once more.
At this point use the Up and Down buttons to calibrate
room temperature, if needed. Press the Mode button to
return to normal operation. NOTE CAUTION ON PAGE 1.
Page 12
Warranty
Five-Year Warranty - This Product is warranted to be free from defects in material and
workmanship. If defect appears within five years from the date of original installation, whether
or not actual use begins on that date, then the product does meet this warranty. A new or
remanufactured part, at the manufacturer’s sole option, to replace any defective part will be
provided without charge for the part itself; PROVIDED the defective part is returned to the
distributor through a qualified servicing dealer.
THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing,
repairing, removing, installing, shipping, servicing or handling of either defective parts or
replacement parts. Such costs may be covered by a separate warranty provided by the installer.
THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION
LOCATION AND BECOMES VOID UPON REINSTALLATION.
LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED
WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE
HEREBY LIMITED IN DURATION TO THE PERIOD FOR WHICH THE LIMITED WARRANTY
IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED
WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE EXPRESSED
WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MANY NOT BE ALTERED,
ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON
WHATSOEVER.
ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING
NORMAL WORKING HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR
REMANUFACTURED, ASSUME AS THEIR WARRANTY PERIOD ONLY THE REMAINING
TIME PERIOD OF THIS WARRANTY.
THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:
1. Normal maintenance as outlined in the installation and servicing instructions or owners
manual including filter cleaning and/or replacement and lubrication.
2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse,
improper servicing, unauthorized alteration or improper operation.
3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other
damages due to the inadequacy or interruption of electrical service.
4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
other conditions beyond the control of the Manufacturer.
5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.
6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and
Canada.
7. Electricity or fuel costs or increases in electricity or fuel costs from any reason whatsoever
including additional or unusual use of supplemental electric heat.
8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL
DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion of
incidental or consequential damages, so the above may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which may vary
form state to state.
P/N 88-343
Rev. 1
Page 13
Form No. OM17-52
Catalog No. 13TS-TA59