NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Important Assembly
Information
MARCY® PRO CIRCUIT TRAINER
PM-4510
Care and Maintenance
Parts List
Warranty
Ordering Parts
Model
PM-4510
Retain This
Manual for
Reference
130301
IMPORTANT: Please read this manual before commencing
OWNER'S
MANUAL
assembly of this product.
IMPEX® INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: (800) 999-8899
www.impex-fitness.com
info@impex-fitness.com
TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................………… 1
IMPORTANT SAFETY NOTICES...................................................................……….. 2
EXERCISE GUIDELINES…………………………………………………………………. 3
WARNING LABEL PLACEMENT.....….....................................................................… 5
IMPORTANT ASSEMBLY INFORMATION.................................................................. 6
OPERATION NOTES……………………………………………………………………….. 7
CARE AND MAINTANENCE, WEIGHT CAPACITY, OPERATING NOTES ………… 8
PARTS LIST…………………………………………………………………………………. 9
EXPLODED DIAGRAM………………………………………………………………………12
COMBINATION LOCK SET UP INSTRUCTION………………………………………… 13
WEIGHT RESISTNACE CHART………………………………………………………….. 14
WARRANTY.................................................................................................…………. 15
ORDERING PARTS.......................................................................................………… 15
BEFORE YOU BEGIN
Thank you for selecting the MARCY PRO HOME GYM PM-4510 by IMPEX®
INC. For your safety and benefit, read this manual carefully before using the
equipment. As a manufacturer, we are committed to provide you complete
customer satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-999-8899
Mon. – Fri. 9 a.m. – 5 p.m. PST
www.impex-fitness.com
info@impex-fitness.com
©IMPEX INC.
1
www.impex-fitness.com
IMPRTANT SAFETY NOTICES
This exercise equipment is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual
before you assemble or operate your equipment. In particular, note the following safety
precautions:
1. Keep children and pets away from the equipment at all times. DO NOT
leave children unattended in the same room with the equipment.
2. Only one person at a time should use the equipment.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the equipment on a clear, leveled surface. DO NOT use the equipment
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the equipment. Running
or aerobic shoes are also required when using the equipment.
7. Use the equipment only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the equipment.
9. Disabled person should not use the equipment.
10. Before using the equipment to exercise, always do stretching exercises to
properly warm up.
11. Never operate the equipment if the equipment is not functioning properly.
12. A spotter is recommended during exercise.
13. This equipment is designed and intended for home and consumer use only, not for
commercial use.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE
OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL
INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES
NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE
SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.
©IMPEX INC.
2
www.impex-fitness.com
EXECISE GUIDELINES
Building Muscle and Gaining Weight
Unlike aerobic exercise, which emphasizes endurance training, anaerobic exercise focuses on
strength training. A gradual weight gain can occur while building the size and strength of muscles.
While developing muscle mass, your body adapts to the stress placed upon it. You can modify your
diet to include foods such as meat, fish and vegetables. These foods help muscles recover and
replenish important nutrients after a strenuous workout.
Muscle Strength and Endurance
To achieve the greatest benefit from exercise, it is important to develop an exercise program that
allows you to work all of the major muscle groups equally.
To increase muscles strength; follow this principle:
Increasing resistance and maintaining the number of repetitions of an exercise results in increased
muscle strength.
To tone your body, follow the principle: Decreasing resistance plus increasing the number of
repetitions of an exercise results in increased body tone.
Once you feel comfortable with an exercise, you can change the resistance, the number of
repetitions, or the speed at which you do the exercise. It is not necessary to change all three
variables. For example, let’s say that you are training at 50 lbs and performing the exercise 10 times
in 3 minutes. When this becomes too easy, you may decide to move up lifting 60 lbs for the same
number of repetitions in the same amount of time. Lifting more weights fewer times most often
develops muscle strength. To gain both muscle strength and endurance, it is recommended that you
perform each exercise 15 to 20 reps per set.
Training Intensity
How hard you begin to train depends on your overall level of fitness. The soreness you experienced
can be lessened by decreasing the load you place on your muscles and by performing fewer sets. To
avoid injury, you should gradually work into an exercise program and set the load to your individual
fitness level. The load should increase as your fitness level increases.
Muscle soreness is common, especially when you first start exercising. If you are painfully sore for a
long time, it may be time to change your program. Eventually, your muscle system will become
accustomed to the stress and strain placed on it.
Beginning a Strength Building Program
Warming Up
To begin strength training, it is important to stretch and perform light exercise for 5 to 10 minutes.
This helps prepare the body for more strenuous exercise by increasing circulation, raising your body
temperature and developing more oxygen to your muscles.
©IMPEX INC.
3
www.impex-fitness.com
Workout
Each workout to keep in mind that muscle soreness that lasts for a long period in not desirable and
may mean that injury has occurred.
Cool Down
At the end of each workout, perform slow stretching exercises for 5 to 10 minutes. Ease into each
stretch only going as far as you can. This stage allows your muscles wind down after training.
To provide a total workout program it is also recommended that 2 to 3 days of aerobic exercise is
performed in addition to the strength training.
Drinking Water
For the body to function properly, it must be properly hydrated. If you are exercising, you should
increase your fluid intake. The reason for this is that the water you take in will leave your system
through the sweating mechanism that cools your body during exercise. The water you lose through
exercise must be replaced so that the muscles can recover properly.
Rest Day
Although you may not feel like doing it, taking a rest day at least once a week is important because it
gives you body a chance to heal it self. Continuously working your muscle will result in over training
which will not benefit in the long run.
©IMPEX INC.
4
www.impex-fitness.com
WARNING LABEL PLACEMENT
©IMPEX INC.
5
www.impex-fitness.com
The warning labels shown here have been placed on the Base and Vertical Frame. If the labels are missing or
illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location
shown.
IMPORTANT ASSEMBLY INFORMATION





Tools Required for Assembling the Bench: Two Adjustable Wrenches and Allen
Wrenches.
NOTE: It is strongly recommended that this equipment is assembled by two or more
people to avoid possible injury.
Ensure Carriage Bolts are inserted through the SQUARE holes on components that need to
be assembled. Attach washer only to end of the Carriage Bolt.
Use Allen Bolts or Hex Bolts inserted through the ROUND hole on components that need to
be assembled.
Always wait until all bolts are assembled onto the bench before tightening the bolts. Do not
tighten each bolt right after it is installed
Fasten Nuts and Bolts
Securely tighten all Nuts and Bolts after all
components have been assembled in current and
previous steps.
NOTE: Do not over tighten any component with
pivoting function.
Make sure all pivoting components are able to move
freely.
Do not tighten all Nuts and Bolts in this step.
Guide Rod Installation
The Guide Rods (#19) has holes on the rod to lock the weight stack when
not in use. The shorter end of the guide rod with the lock hole will need
to be pointed downwards towards the Guide Rod Base (#8).
©IMPEX INC.
6
www.impex-fitness.com
Weight Plate Installation
Slide weight plates onto Guide Rod from top to bottom. The deep
groove on each weight plate needs to face front and
downwards.
Deep Groove
OPERATION NOTES
Weight Plate Selection
1.
2.
3.
4.
5.
6.
Use the Weight Selector Pin to select the number of weight plates to exercise.
Do not insert weight selector pin while the weight stack or top plate is in elevated position.
Be certain the weight Selector Pin is completely inserted.
Each Weight Plate weights approximately 10lbs.
Please refer to Weight Resistance Chart page.
Never use dumbbells or other means to increase the weight resistance. Use only weight plates
provided by manufacturer.
7. For safety purpose while the equipment is not in use. Insert the Lock Pin into the hole
on Guide Rod, and use Combination Lock to lock the Pin to prevent the movement of
Weight Plates. Please refer to the Combination Lock set up.
Cable Tension Adjustment
Adjust the tension of the Cable System by installingthe head of Bench
Press Cable (#61) to the hole on the Single Floating Pulley Bracket (#25).
If the tension is too loose, move up the Cable head by one hole.
If the tension is too tight, move the Cable head down by one hole.
.
©IMPEX INC.
7
www.impex-fitness.com
CARE AND MAINTENANCE
1. Lubricate moving parts with WD-40 or light oil periodically.
2. Inspect and tighten all parts before using the equipment.
3. The equipment can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
4. Examine the equipment regularly for signs of damages or wear.
5. Replace any defective components immediately and/or keep the equipment out of use until
repair.
6. Failure to examine regularly may affect the safety level of the equipment.
WEIGHT CAPACITY AND DIMENSION
1. Maximum user weight: 300 lbs.
2. Assembled Dimension: 57” x 54” x 86”
©IMPEX INC.
8
www.impex-fitness.com
PM-4510 PARTS LIST
PART NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
©IMPEX INC.
DESCRIPTION
Base Frame
Lower Vertical Frame
Upper Vertical Frame
Lat Bar Pulley Assembly
Seat Diagonal Support Frame
Seat Support
Base Connecting Frame
Guide Rod Base
Guide Rod Upper Frame
Bench Press Base
Backrest Support Frame
Bench Press Support
Leg Developer Holder
Leg Developer
Bench Press Frame
Bench Press Arm
Bench Press Handle
Lat Bar
Guide Rod
Selector Rod
Abdominal Strap
Weight Stack Cover
Foam Roll Tube
Angled Double Floating Pulley Bracket
Single Floating Pulley Bracket
Backrest Diagonal Support
Bench Press Axle
Foot Plate
Seat Bracket
Cable Retainer
Bracket
Bracket
U-shaped Bracket
Bracket
Backrest Board
Bench Press Seat Pad
9
SIZE
Ø 5/8” x 9 1/8”
1 ¾” x 4 ¾”
2” x 5 ½”
3” x 4 ¾”
2 3/8” x 7”
QUANTITY
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
2
1
1
2
1
1
1
2
1
2
1
3
1
1
1
1
1
1
www.impex-fitness.com
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
©IMPEX INC.
Seat Pad
Selector Stem
Weight Plate
T-shaped Lock Pin
Chain
Hook
Bushing
Bushing
Rubber Bumper
Rubber Bumper
Rubber Bumper
Pulley
Pulley Bushing
Pulley Bushing
End Cap
End Cap
End Cap
End Cap
End Cap
End Cap
Cone-shaped End Cap
End Cap
Upper Cable
Lower Cable
Bench Press Cable
Ankle Strap
Single Handle
Weight Selector Lock Pin
Lock Pin
Combination Lock
Handle Grip
Lat Bar Grip
Metal Sleeve
Foam Roll
Carriage Bolt
Carriage Bolt
Hex Bolt
Hex Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
10 lb
15 Link
Ø 5/8” x 3/8”
Ø ½” x 3/8”
Ø 2 3/8” x 1”
Ø 1 ½” x 5/8”
1 7/8” x 1 7/8”
Ø 7/8” x 1”
Ø 7/8” x ¾”
2” x 2”
2” x 2 ¾”
2” x 1 1/8”
1 ½” x 1 ½”
Ø 2”
Ø 2 ¼”
Ø 1”
Ø 1”
99”
200”
79”
Ø 3/8” x 2”
6 ¾”
5 ¾”
M10 x 3 ½”
M10 x 2 ¾”
M12 x 3 ¾”
M12 x 3 1/8”
M10 x 3 ½”
M10 x 3 3/8”
M10 x 3”
M10 x 2 ½”
M10 x 8 ½”
10
1
1
9
1
1
2
6
2
2
1
1
16
4
2
9
9
2
2
2
2
1
2
1
1
1
1
1
1
1
1
2
2
1
2
6
10
4
1
2
2
1
2
2
www.impex-fitness.com
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
©IMPEX INC.
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Allen Bolt
Philips Screw
Washer
Washer
Washer
Aircraft Nut
Aircraft Nut
Philips Screw
Allen Wrench (Tool)
Allen Wrench (Tool)
M10 x 2”
M10 x 1 ¾”
M10 x 1 1/8”
M10 x 1”
M10 x 5/8”
M8 x 3”
M8 x 2 ½”
M8 x 5/8”
M6 x 5/8”
Ø 1”
Ø ¾”
Ø 5/8”
M12
M10
M6 x 3/8”
#5
#6
11
4
7
1
8
5
2
2
6
1
11
63
10
6
41
1
1
1
www.impex-fitness.com
PM-4510 EXPLODED DIAGRAM
©IMPEX INC.
12
www.impex-fitness.com
Combination Lock Set Up Instruction
The Lock is set at the manufacturer to the open at 0-0-0 (all zeros are positioned in the middle).
It is recommended to change the combination to ensure safety.
Please follow the below steps to change the combination:
1. Push and hold the combination adjustment button (#1) as indicated below, while holding
down the adjustment button, turn the numerical dial (#2) to set the desired combination in
the middle. Release the button (#1). Set the two other numerical dials the same way. This
only needs to be done once.
2. To lock, turn the dials so the Lock shows random numbers.
3. To unlock, turn the dials to the combination setup in step one, press the shackle (#3) to
open.
©IMPEX INC.
13
www.impex-fitness.com
PM-4510 WEIGHT RESISTANCE CHART
Weight Plate
1
2
3
4
5
6
7
8
9
Leg Developer
30
40
50
60
70
80
90
100
110
Front Press
40
60
80
100
120
140
160
180
200
Lat Pull
30
40
50
60
70
80
90
100
110
Low Pulley
30
40
50
60
70
80
90
100
110
Note: Each plate weights 10 lbs.
Numbers are approximate. Actual weights may vary.
Values for Butterfly are for each arm.
©IMPEX INC.
14
www.impex-fitness.com
®
IMPEX INC.
LIMITED WARRANTY
®
IMPEX Inc. ("IMPEX ") warrants this product to be free from defects in workmanship and material, under
normal use and service conditions, for a period of two years on the Frame from the date of purchase. This
warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to
replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX
Customer Service Department at 1-800-999-8899. All freights on products returned to IMPEX must be
prepaid by the customer. This warranty does not extend to any product or damage to a product caused by
or attributable to freight damage, abuse, misuse, improper or abnormal usage. No other warranty beyond
that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in
connection with the use or performance of the product or other damages with respect to any economic loss,
loss of property, loss of revenues or profits, loss of enjoyments or use, costs of removal, installation or other
consequential damages or whatsoever natures. Some states do not allow the exclusion or limitation of
incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set forth
herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state.
Register on-line at www.impex-fitness.com
®
IMPEX INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899
during our regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
info@impex-fitness.com
When ordering replacement parts, always give the following information.
1.
2.
3.
4.
Model
Description of Parts
Part Number
Date of Purchase
©IMPEX INC.
15
www.impex-fitness.com