Extron electronics HFX 100 Tx User guide

User Guide
DVI & HDMI®
HFX 100 Series
HFX 100 Tx and HFX 100 Rx HDMI Signal Extenders
68-2260-01 Rev. A
04 13
Safety Instructions
Safety Instructions • English
WARNING: This symbol, D, when used on the product, is intended to
alert the user of the presence of uninsulated dangerous voltage within
the product’s enclosure that may present a risk of electric shock.
ATTENTION: This symbol, I, when used on the product, is intended
to alert the user of important operating and maintenance (servicing)
instructions in the literature provided with the equipment.
Chinese Simplified(简体中文)
警告:D产品上的这个标志意在警告用户该产品机壳内有暴露的危险
电压,有触电危险。
注 意 :I 产 品 上 的 这 个 标 志 意 在 提 示 用 户 设 备 随 附 的 用 户 手 册 中 有
重要的操作和维护(维修)说明。
关于我们产品的安全指南、遵循的规范、EMI/EMF 的兼容性、无障碍
For information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the Extron Safety and
Regulatory Compliance Guide, part number 68-290-01, on the Extron
website, www.extron.com.
安全规范指南,产品编号 68-290-01。
Instructions de sécurité • Français
Chinese Traditional(繁體中文)
avertissement: Ce pictogramme, D, lorsqu’il est utilisé sur le
produit, signale à l’utilisateur la présence à l’intérieur du boîtier
du produit d’une tension électrique dangereuse susceptible de
provoquer un choc électrique.
attention: Ce pictogramme, I, lorsqu’il est utilisé sur le produit,
signale à l’utilisateur des instructions d’utilisation ou de maintenance
importantes qui se trouvent dans la documentation fournie avec le
matériel.
使用的特性等相关内容,敬请访问 Extron 网站 www.extron.cn,参见 Extron
警告: D若產品上使用此符號,是為了提醒使用者,產品機殼內存在著
可能會導致觸電之風險的未絕緣危險電壓。
注意I 若產品上使用此符號,是為了提醒使用者。
有關安全性指導方針、法規遵守、EMI/EMF 相容性、存取範圍和相關主題的詳細
資訊,請瀏覽 Extron 網站:www.extron.cn,然後參閱《Extron 安全性與法規
遵守手冊》,準則編號 68-290-01。
Pour en savoir plus sur les règles de sécurité, la conformité à la
réglementation, la compatibilité EMI/EMF, l’accessibilité, et autres sujets
connexes, lisez les informations de sécurité et de conformité Extron,
réf. 68-290-01, sur le site Extron, www.extron.fr.
Sicherheitsanweisungen • Deutsch
warnung: Dieses Symbol D auf dem Produkt soll den Benutzer
darauf aufmerksam machen, dass im Inneren des Gehäuses dieses
Produktes gefährliche Spannungen herrschen, die nicht isoliert sind
und die einen elektrischen Schlag verursachen können.
Vorsicht: Dieses Symbol I auf dem Produkt soll dem Benutzer in
der im Lieferumfang enthaltenen Dokumentation besonders wichtige
Hinweise zur Bedienung und Wartung (Instandhaltung) geben.
Weitere Informationen über die Sicherheitsrichtlinien, Produkthandhabung,
EMI/EMF-Kompatibilität, Zugänglichkeit und verwandte Themen finden Sie
in den Extron-Richtlinien für Sicherheit und Handhabung (Artikelnummer 68290-01) auf der Extron-Website, www.extron.de.
Instrucciones de seguridad • Español
ADVERTENCIA: Este símbolo, D, cuando se utiliza en el producto,
avisa al usuario de la presencia de voltaje peligroso sin aislar dentro del
producto, lo que puede representar un riesgo de descarga eléctrica.
ATENCIÓN: Este símbolo, I, cuando se utiliza en el producto, avisa
al usuario de la presencia de importantes instrucciones de uso y
mantenimiento recogidas en la documentación proporcionada con
el equipo.
Para obtener información sobre directrices de seguridad, cumplimiento
de normativas, compatibilidad electromagnética, accesibilidad y temas
relacionados, consulte la Guía de cumplimiento de normativas y seguridad
de Extron, referencia 68-290-01, en el sitio Web de Extron, www.extron.es.
Japanese
警告: この記号
D が製品上に表示されている場合は、筐体内に絶縁されて
いない高電圧が流れ、感電の危険があることを示しています。
I
注意: この記号
が製品上に表示されている場合は、本機の取扱説明書に記載されて
いる重要な操作と保守(整備)の指示についてユーザーの注意を喚起するものです。
安全上のご注意、法令遵守、EMI/EMF適合性、その他の関連項目に
ついては、エクストロンのウェブサイトwww.extron.jpより
『 Extron Safety and Regulatory Compliance Guide』 (P/N 68-290-01) をご覧く
ださい。
Korean
경고: 이 기호 D, 가 제품에 사용될 경우, 제품의 인클로저 내에 있는
접지되지 않은 위험한 전류로 인해 사용자가 감전될 위험이 있음을
경고합니다.
주의:
이 기호 I, 가 제품에 사용될 경우, 장비와 함께 제공된 책자에 나와
있는 주요 운영 및 유지보수(정비) 지침을 경고합니다.
안전 가이드라인, 규제 준수, EMI/EMF 호환성, 접근성, 그리고 관련
항목에 대한 자세한 내용은 Extron 웹 사이트(www.extron.co.kr)의
Extron 안전 및 규제 준수 안내서, 68-290-01 조항을 참조하십시오.
FCC Class A Notice
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is
likely to cause interference; the user must correct the interference at his own expense.
NOTE: For more information on safety guidelines, regulatory compliances, EMI/EMF
compatibility, accessibility, and related topics, see the “Extron Safety and
Regulatory Compliance Guide” on the Extron website.
FDA/IEC 60825-1 Requirements
CLASS 1 LASER PRODUCT
Complies with FDA performance standards for laser products except for deviations pursuant
to Laser Notice No. 5, dated June 24, 2007.
The product is intended to be used with the fiber optic cables fully installed.
This product meets the applicable requirements of IEC 60825-1, Edition 1 (2007).
Any service to this product must be carried out by Extron Electronics and its qualified
service personnel.
Copyright
© 2013 Extron Electronics. All rights reserved.
Trademarks
All trademarks mentioned in this guide are the properties of their respective owners.
The following registered trademarks(®), registered service marks(SM), and trademarks(TM) are the property of
RGB Systems, Inc. or Extron Electronics:
Registered Trademarks (®)
AVTrac, Cable Cubby, CrossPoint, eBUS, EDID Manager, EDID Minder, Extron, Flat Field,GlobalViewer, Hideaway, Inline, IP Intercom, IP Link,
Key Minder, LockIt, MediaLink, PoleVault, PURE3, Quantum, SoundField, System Integrator, TouchLink, V-Lock, VersaTools, VN-Matrix,
VoiceLift, WallVault, WindoWall
Registered Service Mark(SM) : S3 Service Support Solutions
Trademarks (™)
AAP, AFL (Accu-Rate Frame Lock), ADSP (Advanced Digital Sync Processing), AIS (Advanced Instruction Set), Auto-Image, CDRS (Class D
Ripple Suppression), DDSP (Digital Display Sync Processing), DMI (Dynamic Motion Interpolation), Driver Configurator, DSP Configurator, DSVP
(Digital Sync Validation Processing), FastBite, FOXBOX, IP Intercom HelpDesk, MAAP, MicroDigital, PowerCage, ProDSP, QS-FPC (QuickSwitch
Front Panel Controller), Scope-Trigger, SIS, Simple Instruction Set, Skew-Free, SpeedMount, SpeedNav, SpeedSwitch, Triple-Action Switching,
XTP, XTP Systems, XTRA, ZipCaddy, ZipClip
Conventions Used in this Guide
Notifications
The following notifications are used in this guide:
WARNING: A warning indicates a situation that has the potential to result in death or
severe injury.
CAUTION: A caution indicates a situation that may result in minor injury.
ATTENTION: Attention indicates a situation that may damage or destroy the product or
associated equipment.
NOTE: A note draws attention to important information.
Specifications Availability
Product specifications are available on the Extron website, www.extron.com.
Contents
Specifications Availability...................................iv
Introduction............................................................ 1
About the HFX 100 Tx and HFX 100 Rx............... 1
Features.............................................................. 1
Application Diagram............................................ 2
Product Label...................................................... 2
Panels and Cables................................................. 3
Front Panel.......................................................... 3
HFX 100 Tx Rear Panel....................................... 3
HFX 100 Rx Rear Panel....................................... 5
Installation...................................................... 7
Reference Information................................. 8
Included Parts..................................................... 8
Mounting............................................................. 9
Desktop Placement......................................... 9
Rack Mounting................................................ 9
Technical Publications Standards and Styles
HFX 100
• Introduction
• Contents
v
HFX 100 • Contents
vi
Introduction
This guide describes the function, installation and operation of the HFX 100 Tx transmitter
and HFX 100 Rx receiver. Unless otherwise stated, the terms “HFX 100,” “HDMI extender,”
and “extender” refer to both units. The term “transmitter” refers to the HFX 100 Tx and the
term “receiver” refers to the HFX 100 Rx.
This Introduction provides the following information:
•
About the HFX 100Tx and HFX 100Rx
•
Features
•
Application Diagram
About the HFX 100 Tx and HFX 100 Rx
The Extron HFX 100 DVI extender comprises of a transmitter (Tx) and receiver (Rx) pair,
which use one multimode fiber optic cable to transmit a signal up to 984 feet (300 m). The
transmitter accepts a single HDMI input and converts it to a proprietary signal that is sent
over the fiber optic cable to the receiver. The receiver converts the signal back to a HDMI
output.
The extender supports DDC and HDCP pass-through.
Features
DVI Signal Extender — converts the HDMI signal to a proprietary format that can be
carried up to 984 feet (300 m) without loss of signal integrity.
Power Supply — Both the transmitter and receiver are powered by a 12 VDC power
supply (provided).
Compatible with other Extron fiber optic products — The HFX 100 is compatible with
Extron fiber DMS I/O boards.
Display Data Channel (DDC) pass-through — ensures that the resolution and refresh
rate of the video input signal matches the capabilities of the display device.
High-bandwidth Digital Content Protection (HDCP) pass-through — ensures that
HDCP-compliant outputs are able to display HDCP-encrypted content.
<Product Name>
HFX 100
• <Section
• Introduction
Title>
1
Application Diagram
Extron
HFX 100 Tx
Transmitter
00
X1
HF
Tx
WER
PO
V
12 MAX
A
--
UT
TP
OU
T
PU
IN
Up to 300m ( 984 ft )
on Multimode Fiber
HDMI
FL
SE
/CLO
OFF
Extron
HFX 100 Rx
Receiver
USB
OPEN
I
HDM
PQLS
BY/ON
STAND
Blu-ray Player
00
X1
HF
WER
PO
V
12 MAX
A
--
Rx
T
PU
IN
UT
TP
OU
HDMI
Flat Panel Display
Figure 1.
Typical HFX 100 Application
Product Label
This label is affixed to the bottom of the unit.
DFX/HFX 100 Series
About
Extron Electronics
1025 East Ball Road
Anaheim, CA 92805
Class 1 Laser Product
21.CFR 1040.10
www.extron.com
HFX 100 • Introduction
33-2458-02
Rev. A
2
Panels and Cables
This section discusses the features and cabling of:
•
Front Panel
•
HFX 100 Tx Rear Panel
•
HFX 100 Rx Rear Panel
Front Panel
Both the Transmitter and Receiver have identical front panels:
a
Extron
Figure 2.
HFX 100 Tx and HFX 100 Rx Front Panel
a Front Panel LED — lights amber if the unit (transmitter or receiver) is receiving power
from the 12 VDC power supply. The Transmitter LED lights green if the unit is receiving
a TMDS clock signal. The Receiver LED lights green if the unit is receiving an optical
signal.
NOTE: During initialization, the LED may need a few seconds to stabilize to the
correct state.
HFX 100 Tx Rear Panel
a
c
POWER
POWER
12V
12V
-- -- A
A MAX
MAX
HFX
HFX 100
100 Tx
Tx
OUTPUT
OUTPUT
INPUT
INPUT
b
3 feet (0.91 m) DVI cable
Figure 3.
HFX 100 Tx Rear Panel
HFX 100 • Panels and Cabling
3
a 12 VDC power input — Connect the provided 12 VDC power supply to the front panel
captive screw connectors. When power is provided to the unit but there is no DVI input,
the front panel lights amber.
Back Panel
Power Receptacle
POWER
12V
1.0A MAX
DC Power Cord
Captive Screw Connector
Ground
+12 VDC
AC Power Cord
Figure 4.
External
Power Supply
(12 VDC, 1 A )
12 VDC Power Connection to HFX 100
ATTENTION:
• Always use a power supply provided by or specified by Extron. Use of an
unauthorized power supply voids all regulatory compliance certification and
may cause damage to the supply and the end product.
• Unless otherwise stated, the AC/DC adapters are not suitable for use in air
handling spaces or in wall cavities. The power supply is to be located within
the same vicinity as the Extron AV processing equipment in an ordinary
location, Pollution Degree 2, secured to the equipment rack within the
dedicated closet, podium, or desk.
• The installation must always be in accordance with the applicable provisions of
National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical
Code part 1, section 16. The power supply shall not be permanently fixed to
building structure or similar structure.
NOTES:
• The length of the exposed wires in the stripping process is critical. The ideal
length is 3/16 inch (5 mm). If it is any longer, the exposed wires may touch,
causing a short circuit between them. If it is any shorter, the wires can be
easily pulled out even if tightly fastened by the captive screws.
• Do not tin the wires. Tinned wire does not hold its shape and can become
loose over time.
b HDMI input connector — Connect a HDMI input to this male connector.
NOTE: With appropriate DVI-D to HDMI cables or adapters, the unit will accept
DVI-D input.
When the transmitter is receiving HDMI input signal, the front panel LED lights green.
HFX 100 • Panels and Cabling
4
c Optical output connector — Connect one end of one multimode fiber optic cable (not
provided) into this LC connector. The other end connects into the LC input connector
on the HFX 100 Rx. The cable can be up to 984 feet (300 m) in length.
CAUTION:
• Possible Damage to Eyesight. The HFX 100 Tx outputs continuous laser
(Class 1 rated), which may be harmful and dangerous to the eyes; use with
caution. Do not look into the rear panel fiber optic cable connector or into the
fiber optic cable itself. Plug the attached dust cap into the optical transceiver
when the fiber optic cable is unplugged.
• Possible radiation exposure. Use of controls or adjustments or
performance of procedures other than those specified herein may result in
hazardous radiation exposure.
HFX 100 Rx Rear Panel
a
c
POWER
POWER
12V
12V
-- -- A
A MAX
MAX
HFX
HFX 100
100 Rx
Rx
INPUT
INPUT
OUTPUT
OUTPUT
b
3 feet (0.91 m) DVI cable
Figure 5.
HFX 100 Rx Rear Panel
a 12 VDC power input — Connect the provided 12 VDC power supply to the front panel
captive screw connectors. When power is provided to the unit but there is no HDMI
input, the front panel lights amber.
See Figure 4, the attention points, and the notes on page 4 before connecting the
power supply.
b HDMI output connector — Connect a HDMI display device to this male connector.
NOTE: With appropriate HDMI to DVI-D cables or adapters, the unit will output an
HDMI signal.
HFX 100 • Panels and Cabling
5
c Optical input connector — Connect one end of the multimode fiber optic cable (not
provided) into this LC connector. The other end connects into the LC output connector
on the HFX 100 Tx.
CAUTION:
• Possible Damage to Eyesight. The HFX 100 Tx outputs continuous laser
(Class 1 rated), which may be harmful and dangerous to the eyes; use with
caution. Do not look into the rear panel fiber optic cable connector or into the
fiber optic cable itself. Plug the attached dust cap into the optical transceiver
when the fiber optic cable is unplugged.
• Possible radiation exposure. Use of controls or adjustments or
performance of procedures other than those specified herein may result in
hazardous radiation exposure.
When the HFX 100 Rx is receiving optical input, the front panel LED lights green.
HFX 100 • Panels and Cabling
6
Installation
To install the HFX 100 extender, follow these instructions:
1. Mount the HFX 100 Tx and HFX 100 Rx in suitable locations (see page 9).
2. Connect the provided power supply to the HFX 100 Tx (see page 4). The front
panel LED lights amber.
3. Connect the provided power supply to the HFX 100 Rx (see page 5). The front
panel LED lights amber.
4. Connect the transmitter and receiver using a multimode fiber optic cable (see
page 5).
5. Connect the HDMI display device to the HFX 100 Rx (see page 5). Do not power
on the display at this time.
6. Connect the HDMI source device to the HFX 100 Tx (see page 4). Do not power on
the source at this time.
7. Power on the display device.
8. Power on the source device.
NOTE: The display device must be powered on before the source device to allow
correct DDC communication between the display and the source while the source
device is booting up.
When the HFX 100 Tx is receiving HDMI input, the front panel lights green.
When the HFX 100 Rx is receiving an optical input, the front panel lights green.
HFX 100 • Installation
7
Reference
Information
This section provides information about:
•
Included Parts
•
Optional Accessories
•
Mounting
Included Parts
Because the HFX 100 Tx and HFX 100 Rx are compatible with other Extron products, they
are sold as individual units.
Description
Part Number
HFX 100 Tx
or
HFX 100 Rx
60-1254-12
60-1254-13
12 VDC, 1A power supply
2-pole, 3.5 mm captive screw connector
4 rubber feet (not attached)
HFX 100 Setup Guide
HFX 100 • Reference Information
8
Mounting
Desktop Placement
Attach the four provided rubber feet to the bottom of the HFX 100 transmitter or receiver
and place it in any convenient location.
Rack Mounting
UL Guidelines for Rack Mounting
The following Underwriters Laboratories (UL) guidelines are relevant to the safe installation of
these products in a rack:
Elevated operating ambient temperature — If the units are installed in a closed or multiunit rack assembly, the operating ambient temperature of the rack environment may be
greater than room ambient temperature. Therefore, install the equipment in an environment
compatible with the maximum ambient temperature (Tma: +122 °F, +50 °C) specified by
Extron.
Reduced air flow — Install the equipment in the rack so that the equipment gets adequate
air flow for safe operation.
Mechanical loading — Mount the equipment in the rack so that uneven mechanical
loading does not create a hazardous condition.
Circuit overloading — Connect the equipment to the supply circuit and consider the effect
that circuit overloading might have on overcurrent protection and supply wiring. Consider
the equipment nameplate ratings when addressing this concern.
Reliable earthing (grounding) — Maintain reliable grounding of rack-mounted equipment.
Pay particular attention to supply connections other than direct connections to the branch
circuit (such as the use of power strips).
Rack Mounting Procedure
To mount the unit on a rack shelf, follow the instructions provided with the shelf accessories.
HFX 100 • Reference Information
9
Extron Warranty
Extron Electronics warrants this product against defects in materials and workmanship for a period of three
years from the date of purchase. In the event of malfunction during the warranty period attributable directly to
faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or
components, to whatever extent it shall deem necessary to restore said product to proper operating condition,
provided that it is returned within the warranty period, with proof of purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
1230 South Lewis Street
Anaheim, CA 92805
U.S.A.
Japan:
Extron Electronics, Japan
Kyodo Building, 16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
Europe and Africa:
Extron Europe
Hanzeboulevard 10
3825 PH Amersfoort
The Netherlands
China:
Extron China
686 Ronghua Road
Songjiang District
Shanghai 201611
China
Asia:
Extron Electronics Asia Pte. Ltd.
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Singapore
Middle East:
Extron Middle East
Dubai Airport Free Zone
F12, PO Box 293666
United Arab Emirates, Dubai
This Limited Warranty does not apply if the fault has been caused by misuse, improper handling care, electrical
or mechanical abuse, abnormal operating conditions, or if modifications were made to the product that were not
authorized by Extron.
NOTE: If a product is defective, please call Extron and ask for an Application Engineer to receive an RA (Return Authorization) number. This will begin the repair process.
USA: 714.491.1500 or 800.633.9876
Asia:65.6383.4400
Europe:31.33.453.4040
Japan:81.3.3511.7655
Units must be returned insured, with shipping charges prepaid. If not insured, you assume the risk of loss or
damage during shipment. Returned units must include the serial number and a description of the problem, as
well as the name of the person to contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect to the product and its
quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable
for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics
has been advised of such damage.
Please note that laws vary from state to state and country to country, and that some provisions of this warranty
may not apply to you.
Extron Headquarters
+1.800.633.9876 (Inside USA/Canada Only)
Extron USA - West
Extron USA - East
+1.714.491.1500+1.919.850.1000
+1.714.491.1517 FAX
+1.919.850.1001 FAX
Extron Europe
+800.3987.6673
(Inside Europe Only)
+31.33.453.4040
+31.33.453.4050 FAX
Extron Asia
+800.7339.8766
(Inside Asia Only)
+65.6383.4400
+65.6383.4664 FAX
Extron Japan
+81.3.3511.7655
+81.3.3511.7656 FAX
Extron China
+4000.398766
(Inside China Only)
+86.21.3760.1568
+86.21.3760.1566 FAX
Extron Middle East
+971.4.299.1800
+971.4.299.1880 FAX
© 2013 Extron Electronics All rights reserved. www.extron.com
Extron Korea
+82.2.3444.1571
+82.2.3444.1575 FAX
Extron India
1800.3070.3777
(Inside India Only)
+91.80.3055.3777
+91.80.3055.3737 FAX