CHICAGO 67537 Specifications

Table of Contents
Safety
Safetye��������������������������������������������������������� 2
Specifications.............................................. 7
Setup........................................................... 7
Operationa���������������������������������������������������� 8
Maintenancei���������������������������������������������� 10
Parts List and Diagram............................... 11
Warranty..................................................... 12
WARNING SYMBOLS AND DEFINITIONS
Setup
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that
follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Operation
Addresses practices not related to personal injury.
IMPORTANT SAFETY INFORMATION
General Power Tool Safety Warnings
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term ″power tool″ in the warnings refers to your mains-operated (corded) power tool.
Maintenance
Work area safety
1. Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Page 2
3. Keep children and bystanders
away while operating a power tool.
Distractions can cause you to lose control.
For technical questions, please call 1-800-444-3353.
Item 67537
1. Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with grounded
power tools. Unmodified plugs and matching
outlets will reduce risk of electric shock.
4. Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the
power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
2. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is grounded.
5. When operating a power tool outdoors,
use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor
use reduces the risk of electric shock.
3. Do not expose power tools to rain or wet
conditions. Water entering a power tool
will increase the risk of electric shock.
6. If operating a power tool in a damp location
is unavoidable, use a Ground Fault Circuit
Interrupter (GFCI) protected supply.
Use of a GFCI reduces the risk of electric shock.
Safety
Electrical safety
2. Use personal protective equipment.
Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes,
hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
3. Prevent unintentional starting.
Ensure the Power Switch is in the off‑position
before connecting to power source, picking up
or carrying the tool.
Carrying power tools with your finger on the
Power Switch or energizing power tools that
have the Power Switch on invites accidents.
4. Remove any adjusting key or wrench
before turning the power tool on.
A wrench or a key left attached to a moving part
of the power tool may result in personal injury.
5. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewelry. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewelry
or long hair can be caught in moving parts.
7. If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust‑related hazards.
8. Only use safety equipment that has been
approved by an appropriate standards agency.
Unapproved safety equipment may not provide
adequate protection. Eye protection must be
ANSI‑approved and breathing protection
must be NIOSH‑approved for the
specific hazards in the work area.
Operation
1. Stay alert, watch what you are doing
and use common sense when operating
a power tool. Do not use a power
tool while you are tired or under the
influence of drugs, alcohol or medication.
A moment of inattention while operating power
tools may result in serious personal injury.
Setup
Personal safety
1. Do not force the power tool. Use the
correct power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
2. Do not use the power tool if the Power Switch
does not turn it on and off.
Any power tool that cannot be controlled with the
Power Switch is dangerous and must be repaired.
Item 67537
3. Disconnect the plug from the power source
before making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the
risk of starting the power tool accidentally.
4. Use clamps or another practical way to secure
and support the work piece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
For technical questions, please call 1-800-444-3353.
Page 3
Maintenance
Power tool use and care
5. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions
to operate the power tool. Power tools are
dangerous in the hands of untrained users.
Safety
6. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
7. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
8. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Setup
Multi-function Tool Safety Warnings
1. Hold power tools by insulated gripping
surfaces when performing an operation where
the cutting tool may contact hidden wiring.
Contact with a ″live″ wire will make exposed metal
parts of the tool ″live″ and shock the operator.
2. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
3. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
Operation
4. Do not lay the tool down until it has come to
a complete stop. Moving parts can grab the
surface and pull the tool out of your control.
5. When using a handheld power tool,
maintain a firm grip on the tool with both
hands to resist starting torque.
6. Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and
unplug it from its electrical outlet before leaving.
7. This product is not a toy.
Keep it out of reach of children.
Maintenance
8. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
In addition, people with pacemakers should:
• Avoid operating alone.
• Do not use with Power Switch locked on.
Page 4
• Properly maintain and inspect to avoid
electrical shock.
• Properly ground power cord. Ground Fault Circuit
Interrupter (GFCI) should also be implemented
– it prevents sustained electrical shock.
9. WARNING: Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities, contains chemicals known [to the State
of California] to cause cancer, birth defects or
other reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or
other masonry products
• Arsenic and chromium from
chemically treated lumber
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
10. WARNING: Handling the cord on this product will
expose you to lead, a chemical known to the State
of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
11. The warnings, precautions, and instructions
discussed in this instruction manual cannot cover all
possible conditions and situations that may occur.
It must be understood by the operator that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the operator.
For technical questions, please call 1-800-444-3353.
Item 67537
Vibration Safety
1. Anyone using vibrating tools regularly or for
an extended period should first be examined
by a doctor and then have regular medical
check-ups to ensure medical problems are not
being caused or worsened from use. Pregnant
women or people who have impaired blood
circulation to the hand, past hand injuries,
nervous system disorders, diabetes, or
Raynaud’s Disease should not use this tool.
If you feel any symptoms related to vibration (such
as tingling, numbness, and white or blue fingers),
seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces
the blood supply to the hands and fingers,
increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the
vibration effects on the user.
Safety
This tool vibrates during use.
Repeated or long‑term exposure to vibration may
cause temporary or permanent physical injury,
particularly to the hands, arms and shoulders.
To reduce the risk of vibration-related injury:
4. Use tools with the lowest vibration
when there is a choice.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping
safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as
explained in this manual. If any abnormal
vibration occurs, stop use immediately.
Setup
SAVE THESE INSTRUCTIONS.
Grounded Tools: Tools with Three Prong Plugs
2. The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected
to the tool’s grounding system and must
never be attached to an electrically “live”
terminal. (See 3-Prong Plug and Outlet.)
3-Prong Plug and Outlet
1. Tools marked with “Grounding Required” have
a three wire cord and three prong grounding
plug. The plug must be connected to a properly
grounded outlet. If the tool should electrically
malfunction or break down, grounding provides
a low resistance path to carry electricity away
from the user, reducing the risk of electric
shock. (See 3-Prong Plug and Outlet.)
Item 67537
3. The tool must be plugged into an appropriate outlet,
properly installed and grounded in accordance
with all codes and ordinances. The plug and outlet
should look like those in the preceding illustration.
(See 3-Prong Plug and Outlet.)
For technical questions, please call 1-800-444-3353.
Page 5
Maintenance
TO PREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING
WIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly
grounded. Do not modify the power cord plug provided with the tool. Never remove the
grounding prong from the plug. Do not use the tool if the power cord or plug is damaged. If damaged, have
it repaired by a service facility before use. If the plug will not fit the outlet, have a proper outlet installed by
a qualified electrician.
Operation
Grounding
Double Insulated Tools: Tools with Two Prong Plugs
Safety
1. Tools marked “Double Insulated” do not
require grounding. They have a special
double insulation system which satisfies
OSHA requirements and complies with
the applicable standards of Underwriters
Laboratories, Inc., the Canadian Standard
Association, and the National Electrical Code.
Outlets for 2-Prong Plug
2. Double insulated tools may be used in either of the
120 volt outlets shown in the preceding illustration.
(See Outlets for 2-Prong Plug.)
Extension Cords
1. Grounded tools require a three wire extension cord.
Double Insulated tools can use either
a two or three wire extension cord.
Setup
2. As the distance from the supply outlet increases,
you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage. (See Table A.)
3. The smaller the gauge number of the wire, the
greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord. (See Table A.)
4. When using more than one extension cord
to make up the total length, make sure
each cord contains at least the minimum
wire size required. (See Table A.)
Operation
5. If you are using one extension cord for more
than one tool, add the nameplate amperes
and use the sum to determine the required
minimum cord size. (See Table A.)
6. If you are using an extension cord outdoors, make
sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.
7. Make sure the extension cord is properly wired
and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.
8. Protect the extension cords from sharp objects,
excessive heat, and damp or wet areas.
Table A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS* (120/240 VOLT)
NAMEPLATE
AMPERES
(at full load)
EXTENSION CORD
LENGTH
25' 50' 75' 100' 150'
0 – 2.0
18
18
18
18
16
2.1 – 3.4
18
18
18
16
14
3.5 – 5.0
18
18
16
14
12
5.1 – 7.0
18
16
14
12
12
7.1 – 12.0
18
14
12
10
-
12.1 – 16.0
14
12
10
-
-
16.1 – 20.0
12
10
-
-
-
* Based on limiting the line voltage drop to five volts at
150% of the rated amperes.
Symbology
Double Insulated
Canadian Standards Association
Maintenance
Underwriters Laboratories, Inc.
V
~
A
Page 6
Volts
Alternating Current
Amperes
OPM
Oscillations Per Minute
WARNING marking concerning Risk
of Eye Injury. Wear ANSI‑approved
safety goggles with side shields.
Read the manual before
set-up and/or use.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.
For technical questions, please call 1-800-444-3353.
Item 67537
Electrical Rating
120 V~ / 60 Hz / 2 A
No Load Speed
10,000 – 20,000 OPM
Safety
Specifications
3146023
Setup - Before Use:
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Note: For additional information regarding the parts listed in the
following pages, refer to Parts List and Diagram on page 11.
Setup
Components
Speed Control Dial
Spindle
Operation
Power Switch
Cutter Blade
Scraper
Maintenance
Sanding Pad
Sandpaper
Figure A: Components and Controls
Item 67537
For technical questions, please call 1-800-444-3353.
Page 7
Operating Instructions
Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
Safety
Tool Set Up
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:
Make sure that the Power Switch is in the off‑position and unplug the tool from
its electrical outlet before performing any procedure in this section.
Attachment Installation
1. Use the Hex Key to remove the Cap Screw (1)
and Flange (2) from the end of the Spindle (3).
Setup
2. Install the desired accessory by placing the
accessory’s mounting holes against the fitting pins
on the Spindle. Accessories may be mounted at
angles up to 90° left or right of straight ahead.
Fitting Pins
Spindle (3)
Note: The long Cutter Blade should only be used
in the straight ahead position. See Figure B.
CAUTION! When attaching the Scraper Blade or
Cutter Blade, orient the accessory so that the blade
faces AWAY from the handle to avoid injury.
Operation
3. Replace the Cap Screw and Flange while holding
the accessory. Make sure the cupped side of
the Flange is toward the tool. While holding the
attachment over the pins on the tool, tighten the
Cap Screw onto the Spindle using the Hex Key.
Torque snugly (approximately 10 ft-lb).
CAUTION! Make sure that the accessory is
held securely in place by the four fitting pins on
the Spindle as the Cap Screw is tightened.
Cutter Blade
Cap Screw (1)
Flange (2)
Figure B: Example of Installed Attachment
4. After securing, the attachment should not move
on the Spindle. If it can move with the power
off, remount it, making sure that the holes on the
attachment line up with the pins on the Spindle.
Tighten the Cap Screw securely.
Note: For sanding, first attach the Sanding Pad to the
tool, then align a sheet of Sandpaper over the pad and
press into place. Once a Sandpaper corner becomes
worn, turn it 120° or replace the sheet with a new one.
Maintenance
Page 8
For technical questions, please call 1-800-444-3353.
Item 67537
Workpiece and Work Area Set Up
2. Route the power cord along a safe route to reach
the work area without creating a tripping hazard or
exposing the power cord to possible damage. The
power cord must reach the work area with enough
extra length to allow free movement while working.
3. Secure loose workpieces using a vise or clamps
(not included) to prevent movement while working.
4. There must not be objects, such as utility lines,
nearby that will present a hazard while working.
Safety
1. Designate a work area that is clean and well‑lit.
The work area must not allow access by children
or pets to prevent distraction and injury.
1. Make sure that the Power Switch is in
the off‑position, then plug in the tool.
5. Avoid contact with foreign objects such as metal
screws and nails when sanding, scraping, or cutting.
2. Hold the Tool with both hands and slide
the Power Switch forward to activate.
6. Do not apply excessive pressure on the Tool.
Allow the Tool to do the work.
3. Adjust the speed of the tool using the Speed
Control Dial. There are six speed settings from
1 (slowest) to 6 (fastest). Determine the optimum
speed by testing on a scrap piece of material.
7. When finished, slide the Power Switch to OFF. Allow
the tool to stop completely before setting it down.
Maintenance
Operation
4. Do not allow contact between Sandpaper,
Scraper, or Blade and workpiece until the
tool is running at the intended speed.
8. To prevent accidents, turn off the tool and
unplug it after use. Clean, then store the
tool indoors out of children’s reach.
Setup
General Operating Instructions
Item 67537
For technical questions, please call 1-800-444-3353.
Page 9
Maintenance and Servicing
Procedures not specifically explained in this manual must
be performed only by a qualified technician.
Safety
TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Make sure that the Power Switch is in the
off‑position and unplug the tool from its electrical outlet before performing any procedure in this section.
TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: Do not use damaged equipment.
If abnormal noise or vibration occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
Setup
1. BEFORE EACH USE, inspect the general
condition of the tool. Check for:
• loose hardware
• misalignment or binding of moving parts
• damaged cord/electrical wiring
• cracked or broken parts
• any other condition that may
affect its safe operation.
2. AFTER USE, wipe external surfaces
of the tool with clean cloth.
3. If performance decreases, have the
unit serviced and Carbon Brushes
replaced by a qualified technician.
4.
WARNING! If the supply cord of this
power tool is damaged, it must be replaced
only by a qualified service technician.
Troubleshooting
Problem
Possible Causes
Tool will not start. 1. Cord not connected.
2. No power at outlet.
Operation
Tool operates
slowly.
Performance
decreases
over time.
Maintenance
Excessive noise
or rattling.
Overheating.
Likely Solutions
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered,
turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right
capacity for tool and circuit has no other loads.
3. Turn off tool and allow to cool.
Press reset button on tool.
4. Have technician service tool.
3. Tool’s thermal reset breaker
tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or Power
Switch, for example.)
1. Forcing tool to work too fast.
1. Allow tool to work at its own rate.
2. Extension cord too long or cord 2. Eliminate use of extension cord. If an extension
diameter too small.
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 5.
1. Carbon brushes worn
1. Have qualified technician replace brushes.
or damaged.
2. Attachment dull or damaged.
2. Keep cutting accessories sharp. Replace as needed.
Internal damage or wear. (Carbon Have technician service tool.
brushes or bearings, for example.)
1. Forcing tool to work too fast.
1. Allow tool to work at its own rate.
2. Attachment dull or damaged.
2. Keep cutting accessories sharp. Replace as needed.
3. Blocked motor housing vents.
3. Wear ANSI-approved safety goggles and
NIOSH‑approved dust mask/respirator while
blowing dust out of motor using compressed air.
4. Motor being strained by long or 4. Eliminate use of extension cord. If an extension
small diameter extension cord.
cord is needed, use one with the proper diameter
for its length and load. See Extension Cords
in Grounding section on page 5.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Page 10
For technical questions, please call 1-800-444-3353.
Item 67537
Parts List and Diagram
Description
Cap Screw M8 x 12
Flange
Spindle
Rubber Casing
Circlip
Spring Washer
Bearing 6000
Block
Bushing
Screw ST4.0 x 25
Front Housing
Circlip
Bearing 625
Washer
Qty
1
1
1
1
1
1
1
1
1
4
1
1
1
1
Part
15
16
17
18
19
20
21
22
23
24
25
26
28
29
Description
Cover
Bearing 608
Washer
Armature
Bearing 607
Bushing
Guide Ring
Screw ST4.0 x 55
Stator
Power Switch
Link Plate
Middle Housing
Brush Holder
Carbon Brush
Qty
1
1
1
1
1
1
1
2
1
1
1
1
2
2
Part
30
31
32
33
34
35
36
37
38
39
40
41
42
Description
Rivet
Screw ST4.0 x 12
Rear Housing (left)
Internal Switch
Brace
Clip
Screw ST3.0 x 8
Power Cord
Cable Sheath
Speed Control Dial
Rear Housing (right)
Screw ST4.0 x 25
Screw ST4.0 x 32
Qty
4
2
1
1
1
1
2
1
1
1
1
1
2
Maintenance
Operation
Setup
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Safety
Part
Record Product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only,
and are not available individually as replacement parts.
Item 67537
For technical questions, please call 1-800-444-3353.
Page 11
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards,
and warrants to the original purchaser that this product is free from defects in materials and workmanship for the
period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly,
to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper
installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries
to persons or property, or for incidental, contingent, special or consequential damages arising from the use of
our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353