American Weigh CD-V2-500 User manual

CD-V2 User Manual

Thank you for purchasing the American Weigh CD-V2 digital pocket scale.

Please read all operating instructions carefully before use. Scales are precision measuring devices and should always be handled with proper care. To ensure years of reliable service, keep these simple tips in mind:

• Do not exceed the scale’s maximum capacity. Overloading your scale can permanently damage it!

• Avoid exposure to extreme heat or cold. Scales perform best at normal room temperature. If temperatures have changed dramatically, calibration and adjustment may be necessary.

• Allow your scale to warm up for 30-60 seconds before performing calibration and adjustment(if available).

• Store your scale in a clean, dry location. Dust, dirt, and moisture can accumulate on the weighing sensors and electronics causing inaccuracy or malfunction.

• Avoid using your scale in close proximity to strong radio wave emitting devices such as computers, cash registers, and cordless phones.

• Always weigh on a flat and level surface, free from vibrations and drafts.

The corner of a room is usually the most stable.

• Gently apply all items to be weighed. Do not drop items onto the weighing platform.

• Avoid dropping your scale. The warranty does not cover damage due to rough treatment or overload.

• Check the batteries first if you are having any trouble with your scale. This simple step can remedy most scale issues.

• Do not disassemble your scale. This product contains no user serviceable parts.

I. Part List

1. Scale

2. Vinyl Pouch

3. CD Inserts (x5)

4. CR2032 Batteries (x2)

II. Key Description

PCS Key

Unit Key

PCS

UNITS

III. Battery Installation

1. Before using the scale for the first time, check the battery compartment and remove any plastic insulation strips or packaging that may be in place to prevent battery drainage during shipping/storage.

2. If you are replacing the batteries, make sure the positive and negative contacts are properly aligned.

I/O M T

ON/OFF

TARE

L

ON/Off Key

Tare Key

IV. Operation

1. Place the scale on a flat, level surface and press the ON/OFF key to turn the scale on.

2. Once the start-up process completes and the scale goes to zero you are ready to weigh.

3. Place the quantity to be weighed onto the weighing platform.

4. Wait a couple seconds for the display to stabilize before taking a weight reading.

V. Changing the Unit of Measure

1. Press the UNITS key to change the scales displayed unit of measure.

2. If the scale is turned off then back on, it will default to the last unit used.

• CD-V2-100 Units: g (gram) oz (ounce) ct (carat) gn (grain)

• CD-V2-500 Units: g (gram) oz (ounce) ozt (troy ounce) dwt (pennyweight)

VI. Using the Tare Feature

You can use this scale’s tare feature to subtract the weight of an empty container or vessel for net weight determination.

NOTE: The weight of the container will subtract from the available capacity.

1. Place the empty container or vessel on the weighing platform.

2. Press the TARE key once. The display will then reset to zero. If the container is removed, it’s weight will be displayed as a negative number.

3. You may now fill the container with the quantity to be weighed. The display will show the net weight of the contents.

4. To return to normal weight display (gross weight), remove any items from the weighing platform and press the

TARE key again to re-zero the scale.

VII. Calibration

Calibration and adjustment are performed at the factory. However, the weighing range can shift slightly during shipping.

Also, due to changes in local acceleration of gravity around the world, adjustment is recommended when moving the scale from one location to another. To check calibration:

1. Place the required calibration weight on the scale and note the displayed value.

2. If the displayed value is not within acceptable tolerance (see chart below), adjustment is required.

Model

CD-V2-100

Acceptable

Tolerance (±)

0.03g

Calibration

Weight

100g

Recommended

Accuracy Class

OIML M2

CD-V2-500 0.2g

500g OIML M2

VIII. Adjustment

1. Turn the scale OFF.

2. Press and hold the UNITS key until the display shows CAL then release

3. Press the UNITS key again. The display will flash CAL followed by the required calibration weight (see chart).

4. Place the required weight on the center of the platform.

5. Once the weight is confirmed, the display will show “PASS” and return to normal weighing. Calibration complete!

IX. Troubleshooting

• Problem: Scale will not turn on

• Solution: Check the batteries

• Problem: Displayed weight fluctuates randomly

• Solution: Make sure your workspace is stable and free of any air currents or vibration

• Problem: Displayed weight is inaccurate

• Solution: Perform a calibration adjustment

X. Error Codes

1. OUTZ - Zero range has shifted. Perform calibration adjustment. If the problem persists, the load cell may be permanently damaged due to overloading.

2. UNST - Scale is unstable. Use in a more stable position.

3. HHHHH - Maximum capacity exceeded. Remove the extra weight to avoid damaging the load cell.

4. L - Batteries are low. Replace the batteries.

XI. Specifications

Max. Capacity

Readability

Power

Dimensions

Platform Dimensions

Warranty

CD-V2-100

100g / 3.527oz / 500ct / 1543.2gn

CD-V2-500

500g / 17.635oz / 16.075ozt / 321.5dwt

0.01g / 0.001oz / 0.05ct / 0.1gn

0.1g / 0.005oz / 0.005ozt / 0.1dwt

2 x CR2032 Lithium Batteries

0.5 x 4.9 x 5.5”

4” diameter

10 Year Limited Warranty