Westinghouse LVM-42w2 User`s manual

USER’S MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USUARIO
LVM-42w2
HD Video Monitor
Moniteur Vidéo HD
Monitor de Video de Alta Definición
www.westinghousedigital.com
Westinghouse Digital Electronics
Santa Fe Springs, CA
SE-UM-4202-0501
Contents
INSTALLATION
Package Contents……………………………….……………………….6
Front View of the HD Video Monitor……………..……………………. 7
Rear View of the HD Video Monitor……………….………..…………. 7
Side View of the HD Video Monitor…..……………………...…………8
Remote Control…………………..…………………………..………… 10
Installation………….…………………………………………………….11
OSD Functions
PICTURE PARAMETERS: Brightness / Contrast / Saturation / Hue /
Color Temp / Sharpness / Aspect Ratio /
Backlight / Reset……………………..…... .15
PC PARAMETERS: Auto Adjust / Clock / Phase / Position………..……. 16
AUDIO SETTINGS: Volume / Bass / Treble / Balance / Mute / Speaker /
Reset…………………...……………....….….….. 17
PICTURE-IN-PICTURE: Display Mode / Main Source / PIP Source /
Swap / PIP Position / PIP Size / Audio From….. 18
GENERAL SETTINGS: Menu Position / Menu Timeout / Language /
Sleep Timer / Transparency / DPMS / LED /
System Info / Factory Reset………...….….…... 19
Specifications………………………………………….………………… 20
Troubleshooting ………………..………………………………………..21
English
Important Product Safety Instructions………………………………….2
Safety Guidelines….………….………………………………………….4
Cleaning the HD Video Monitor………………..……………….…….... 5
English
1
Important Product Safety Instructions
Overloading
Do not overload wall outlets, extension cords, or power strips. This can result in fire or
electronic shock.
Power Cord Protection
Power supply cords should be routed so that they are not likely to be walked on or pinched
by items placed upon or against them. Periodically inspect the cords and each end of the
cords for damage. The HD Monitor shall be installed near a wall socket outlet and the plug
on power cord shall be readily accessible.
Ventilation
Slots and openings on the cabinet are provided for ventilation purposes. To ensure reliable
operation of the HD Monitor and to protect it from overheating, these openings must not be
blocked or covered.
• Do not block the openings by placing the HD Monitor on a bed, sofa, rug or other
similar surface.
• Do not place the HD Monitor in a built-in installation such as a bookcase or rack
unless proper ventilation is provided and the manufacturer’s instruction have been
adhered to.
Other Notices
• Avoid exposing the HD Monitor to direct sunlight or high temperatures.
• Avoid exposing the HD Monitor to moisture or high humidity.
• Do not attempt repairs yourself. Your warranty does not cover repairs or attempted
repairs by anyone not authorized by Westinghouse Digital.
• If the HD Monitor will not be used for a long period of time, unplug the HD Monitor
and remove the batteries from the remote control.
Precautions
• Avoid touching the screen. Skin oils are difficult to remove.
• Never remove the rear cover. The HD Monitor contains high-voltage parts. You may
be seriously injured if you touch them.
• Avoid exposing the HD Monitor to direct sunlight or another heat source. Orient the
HD Monitor away from direct sunlight to reduce glare.
• Always handle the HD display with care when moving it.
• Place the HD Monitor in a well-ventilated area; don’t place the HD Monitor in airtight
compartments. Do not place anything on the HD Monitor that prevents heat
dissipation.
• Ensure that the area around the HD Monitor is clean and free of moisture.
• Do not place heavy objects on the HD Monitor, audio/video cables, or power cord.
• If the HD Monitor emits smoke, abnormal noise, or a strange odor, immediately turn
it off and contact the Westinghouse Service Center.
•
WARNING – To Reduce The Risk Of Fire Or Electric Shock, Do Not Expose
The HD Monitor To Rain Or Moisture! The HD Monitor shall not be exposed to
dripping or splashing and objects filled with liquids, such as vases, shall not be
placed on the Monitor.
2
English
Follow and obey all warnings and instructions marked on the HD Video Monitor. For your
safety, please read all the safety and operating instructions before you operate the HD
Monitor Keep this user’s manual for future reference.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use the HD Monitor near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or
other apparatus (including amplifiers) that produce heat.
9) Do not attempt to bypass the safety purpose of the polarized or grounding- type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. If the provided
plug does not fit into your wall outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at the ends of
the cord.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer,
or sold with the HD Monitor. When a cart is used, use caution when moving the cart
to avoid injury or damage.
13) Unplug the HD Monitor during lightning storms or when it is not being used for a
long period of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
HD Monitor has been damaged in any way, such as the power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the HD Monitor, it has
been exposed to rain or moisture, it does not operate normally, or the TV has been
dropped.
Antenna Installation Safety
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the HD Monitor, be sure the antenna or
cable system is grounded to prevent voltage surges and built-up static charges. Article 810 of the
National Electrical Code, ANS/NFPA 70, provides information on proper grounding of the mast and
supporting structure, grounding of the lead-in wire to an antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode.
Lightning
For added protection for the HD Monitor during a lightning storm, or when it is left unattended and
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the HD Monitor due to lightning and power-line surges. Do
not disconnect the antenna or the power cord during a heavy storm – lightning may strike while
you are holding the cable cord, causing serious injury. Turn off your HD MONITOR and wait for
the weather to improve.
Power Lines
An outside antenna system should not be located in the vicinity of overhead power lines or other
electric light or power circuits. When installing an outside antenna system, extreme care should
be taken to keep from touching such power lines or circuits.
3
English
1)
2)
3)
4)
5)
6)
7)
Safety Guidelines
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The specific power cord for this HD Monitor is enclosed and has been selected according to the country of
destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to
replace the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must
meet IEC-60320 requirements and should look like Figure A1 below:
Figure A1
Figure A2
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For LCD Monitors that are placed on a desk or table, type SVT or SJT cord sets may be used. For
LCD Monitors placed directly on the floor, only SJT type cord sets may be used. The cord set must be
selected according to the current rating for the LCD Monitor. Please consult the table below for the selection
criteria for power cords used in the United States and Canada.
Cord Type
Size of Conductors in Cord Maximum Current Rating of Unit
SJT
SVT
18 AWG
16 AWG
14 AWG
18 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
FCC Compliance Statement
This equipment has been tested and complies with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and may
cause harmful interference to radio communications if not installed and used in accordance with the
instructions. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the LCD Monitor and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the Westinghouse Service Center or an experienced radio/Monitor technician for assistance.
FCC Warning
To assure continued FCC compliance, the user must use a grounded power supply cord and the
provided shielded video interface cable with bonded ferrite cores. If a BNC cable is used, use only a
shielded BNC (5) cable. Also, any unauthorized changes or modifications not expressly approved by
Westinghouse Digital will void the user's authority to operate this device.
4
English
CAUTION: The power supply outlet should be located near the HD Monitor and should be easily accessible.
Always use the appropriate AC cord that is certified for your specific country. Some examples are listed
below:
USA..................UL
Switzerland ..... SEV
Canada.............CSA
Britain ............. BASE/BS
Germany..........VDE
Japan ............... Electric Appliance Control Act
Cleaning the HD Video Monitor
MAKE SURE THE HD Monitor IS TURNED OFF
NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE
To clean the screen:
1. Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based glass
cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If it still is not clean, apply a small amount of non-ammonia, non-alcohol based, mild nonabrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
Westinghouse Digital does not recommend the use of any ammonia or alcohol-based cleaners on
the HD Monitor screen or case. Some chemical cleaners have been reported to damage the
screen and/or HD Monitor case. Westinghouse Digital will not be liable for damage resulting from
the use of any ammonia or alcohol-based cleaners.
5
English
•
•
INSTALLATION
English
Package Contents
Your product package includes:
• 42” Westinghouse HD Video Monitor
• Remote Control (with batteries)
• Power Cord
• Quick Connect Guide
• User’s Manual
• Warranty Card
6
Front View of the HD Video Monitor
“IR” receiver and
LED indicator
Speakers
Rear View of the HD Video Monitor
7
English
Use the buttons on the right side of the HD Monitor or on the remote control to display the
On Screen Display (OSD). The OSD controls are defined in “OSD Functions” on page 12.
Side View of the HD Video Monitor
English
1. Menu
Turn OSD Menu ON/OFF
2. Volume + / -
Increase/Decrease sound volume or
adjust a highlighted control while in the
OSD Menu.
3. OSD Selection T/S
Highlight a control while in the OSD
Menu.
4. Input
Select Active Video Input or choose a
selection while in the OSD MENU.
5. Power Button
Turn Power ON/OFF
8
Side View of the HD Video Monitor
6. AV Video Input
Connect to an external video device such as a VHS player or video
game system.
7. AV & S-Video Audio Input (Right / Left)
Connect an external audio source to this jack; (Audio (R/L). This
connection supports either S-Video or AV input.
8. Audio Output (Right / Left)
Connect this output to an external stereo audio amplifier, receiver or
surround sound processor.
9. VGA Audio IN
Using the cable provided, connect to the Audio out (Green) from a
computer.
10. VGA
Using a 15-pin VGA cable, connect to a computer or other device
with a VGA output.
11. DVI1 Audio Input (Right / Left)
Connect an external DVI audio source to this jack.
12. DVI1 (Supports up to 1080p Full HD)
Using a 20-pin DVI cable, connect to a computer, HD Digital
cable/satellite receiver, HD Set-Top-Box, DVD or other device with a
DVI output.
13. YPbPr1 (HD) Input
Connect an external video device such as DVD or video game
system with component output to these jacks.
14. YPbPr2 (HD) Input
Connect an external video device such as DVD or video game
system with component output to these jacks.
15. YPbPr1 Audio 1 Input (Left / Right)
Connect an external audio source to this jack.
16. YPbPr2 Audio 2 Input (Left / Right)
Connect an external audio source to this jack.
17. AC IN (Power)
Connect the power cord from AC IN to a power source.
9
English
1. DVI2 (Supports up to 1080p Full HD)
Using a 20-pin DVI cable, connect to a computer, HD Digital
cable/satellite receiver, HD Set-Top-Box, DVD or other device with a
DVI output.
2. DVI2 Audio Input (Right / Left)
Connect an external DVI audio source to this jack.
3. HDMI Input
Connect to an external video device such as HD Digital
cable/satellite receiver, HD Set-Top-Box, Media Center PC, or DVD
player.
4. HDMI Audio Input (Right / Left)
Connect the audio input if you using a DVI-to-HDMI converter.
5. S-Video Input
Connect to an external video device such as a VHS player.
Remote Control
The Remote Control will transmit to the HD Monitor up to 10 feet away.
10
English
1. POWER:
Switch the power On/Off
2. INPUT
Select input source
3. OSD SUB-MENU SELECTION
Select OSD sub-menu option directly
4. PREVIOUS OSD MENU
Select previous OSD menu
5. MENU/EXIT
Turn OSD Menu On/Off.
6. SCALING
Select Video Display format “STANDARD” or
“FILL”
7. T / S / W / X
OSD MENU control
8. Enter
Execute a command
9. MUTE
Turn the Sound On/Off
10. INFO
Display the source and channel information
11. PIP
Display sub-picture On/Off
12. FREEZE
Freeze main screen
13. VOL - / +
Volume Up/Down adjustment
14. SOURCE T / S
Source selection Up/Down
15. YPbPr
Select YPbPr1 / YPbPr2 source input
16. VGA
Select VGA source input
17. DVI
Select DVI1 / DVI2 / HDMI source input
18. S-Video
Select S-Video source input
19. AV
Select AV source input
Installation
1. Insert Remote Control Batteries
3) Re-attach the battery cover.
CAUTION:
z
z
z
z
z
z
Only use AAA batteries.
Do not mix new and old batteries. This may result in cracking or leakage, which
may pose a fire risk or lead to personal injury.
Insert batteries according to (+) and (−) markings. Inserting the batteries incorrectly
may result in cracking or leakage, which may pose a fire risk or lead to personal injury.
Dispose of used batteries in accordance with local laws and regulations.
Keep batteries away from children and pets.
When the remote control will not to be used for an extended period, remove the batteries.
11
English
1) Remove the battery cover.
2) Insert the batteries corresponding to the (+) and (−) marks on the battery
compartment.
2. Connect audio and video cables from a PC
Connect one or all of the following into the back of the HD Monitor
VGA CONNECTION: Connect an analog VGA cable from your PC VGA OUT port to
the HD Monitor VGA IN port.
DVI1/DVI2 CONNECTION: Connect a Digital DVI cable from your PC DVI OUT port
to one of the HD Monitor DVI-HDCP port.
AUDIO CONNECTION: Connect a stereo mini cable from the PC’s AUDIO OUT port
to the AUDIO IN port on the HD Monitor.
3. Connect AV, Component, S-Video to Video Devices
Connect Audio/Video cables from compatible devices to the back panel of the HD
Monitor.
12
English
IMPORTANT: Before beginning, make sure all devices are turned off.
4. Connect power cables
Connect the power cord to the HD Monitor then to a properly grounded AC outlet.
English
5. Turn Power On
Press the Power ON button on the right side of the HD Monitor, or press the Power ON
(Red) button on the remote control.
6. Select input source for the HD Monitor using the OSD menu or
remote control
7. If connecting to a PC (VGA/DVI1/DVI2):
For the best picture quality, set the HD Monitor resolution to 1920 x 1080 at 60Hz
(refer to the graphic card’s user guide to set this resolution).
13
OSD Function
To display the OSD main menu, press the Menu button on the right side of front control
keys of the HD Monitor or the MENU key on the remote control. Use 3/4 arrow keys to
highlight the desired OSD sub-menu.
Main Menu
To select a sub-menu, press ▲/▼ on the right side of the HD Monitor or the ▲/▼ key on
the remote control. Also, by using the number keys on the remote control, you can select a
OSD sub-menu directly.
14
English
All the OSD function settings are controlled either by the remote control or using the
control keys on the right side of HD Monitor.
PICTURE PARAMETERS:
English
Function Name
Brightness
Contrast
Saturation
Hue
Color Temp
Function
Aspect Ratio
Brightness adjustment
Contrast adjustment
Saturation adjustment
Hue adjustment
Color temperature adjustment (Color 1, Color 2, Color 3)
Sharpness adjustment
(Sharpness cannot be adjusted in PC mode)
Set display to “STANDARD” / “FILL”
Backlight
Backlight adjustment
Reset
Reset video settings
Sharpness
15
PC PARAMETERS:
English
Function Name
Auto Adjust
Clock
Phase
Position
Function
Automatically adjust the horizontal phase of the image
Clock adjustment
Phase adjustment
Adjust the horizontal and vertical position of the image
NOTE: The GRAPHIC menu is only available when VGA source is selected.
16
AUDIO SETTINGS:
English
Function Name
Volume
Bass
Treble
Balance
Mute
Speaker
Reset
Function
Volume adjustment
Bass adjustment
Treble adjustment
Balance adjustment
Select Audio OFF or ON
Select internal or external speaker
Reset audio settings
17
PICTURE-IN-PICTURE:
English
Function Name
Display Mode
Main Source
Function
OFF --> PIP --> PBP --> POP
Select main screen sources
VGA --> DVI1--> DVI2 --> AV --> S-Video--> YPbPr1 -->
YPbPr2 --> HDMI
PIP Source
Select sub screen sources
Please see PIP/PBP/POP specification in Table 1
Swap main screen and sub-screen source
Sub-screen display horizontal/vertical position adjustment
Sub-screen display size adjustment
(Small -->Medium --> Large)
Select main screen or sub-screen audio sources
Swap
PIP Position
PIP Size
Audio From
Table 1:
SUB
VGA
DVI1
AV
S-Video
YPbPr1
YPbPr2
DVI2
HDMI
VGA
X
O
O
O
X
X
O
O
DVI1
O
X
O
O
O
O
O
O
AV
O
O
X
X
O
O
O
O
S-Video
O
O
X
X
O
O
O
O
YPbPr1
X
O
O
O
X
X
O
O
YPbPr2
X
O
O
O
X
X
O
O
DVI2
O
O
O
O
O
O
X
X
HDMI
O
O
O
O
O
O
X
X
Main
18
GENERAL SETTINGS:
English
Function Name
Menu Position
Menu Timeout
Language
Sleep Timer
Transparency
DPMS
LED
System Info
Factory Reset
Function
OSD horizontal/vertical position adjustment
Set the time to turn off the OSD automatically
OSD language selection
Set sleep timer to turn off the power automatically
Set OSD transparency level
Select DPMS On/Off
Turn the LED ON or OFF
Display Input source, type and signal
Restore factory default settings
19
Specifications
Type
42(42.02wable diagonal area), TFT (Thin Film Transistor), Active Matrix
WXGA LCD, 1920*1080 vertical stripe
Color
Anti-reflective coating + Anti-glare coating
176° (H) / 176° (V)
Viewing Angles
Output Signal
RGB Analog * 1 (75 ohms, 0.7 Vp-p)/Mini-Stereo *1
H/V separated (TTL) for PC
DVI-D * 2 (HDCP support) / RCA (L/R) * 2
DVI1 & DVI2 supports up to 1080P
fh: 30-80 kHz, fv: 50-75 Hz
Component Video (YPbPr) * 2 / RCA (L/R) Stereo * 2
YPbPr 1 & 2 supports up to 720p/1080i
Composite Video* 1 / S–Video * 1 / RCA (L/R) stereo * 1
Supports up to 480p
HDMI * 1 / RCA (L/R) stereo * 1
Supports up to 720p/1080i/1080p
RCA (L/R) Stereo * 1
HDTV Compatibility
480i, 480P, 720P, 1080i
Input Signal
PC Compatible
Video/Audio
Supported
1920 x 1080 @ 60 Hz
Voltage
1280 x 1024 @ 60, 75 Hz
1280 x 768 @ 60, 75Hz
1024 x 768 @ 60, 75 Hz
800 x 600 @ 60, 75 Hz
640 x 480 @ 60, 75 Hz
720 x 400 @ 70 Hz
10W (x2 Channels) / Subwoofer * 1 (10W)
100-240 VAC, 50/60 Hz (auto switch), 2.7A (MAX)
(VGA, DVI1, & DVI2)
Speaker Output
Power
Operating Conditions Temperature
Humidity
Altitude
0° C to + 35° C (32° F to + 95° F)
10% to 90% (no condensation)
To 3,000 m
Temperature
-20° C to + 60° C (-4° F to + 140° F)
Humidity
10% to 90% (no condensation)
Altitude
To 12,000m
Dimensions
Physical
1049.8mm (W) X 718.9 mm (H) x 225.9 mm (D)
Weight
Net / Gross
57.3 lb (26kgs) / 73.8 lb (33.5kgs)
Storage Conditions
FCC-B, UL/c-UL
Regulations
Power
On (Normal)
270W (White LED)
Power
Off
<2W
Power
Saving
<3W (White LED)
Preset Timing Mode (Pre-adjusted to reduce blanking: 1920x1080 at 60Hz)
Warning: Do not set the graphics card in your computer to exceed these refresh rates; if refresh rates over spec,
OSD will show the "Out of range" message and LCD will be going to power saving mode.
Note: Product Specifications are subject to change without notice.
20
English
Panel
Troubleshooting
No Power
Make sure power button is ON (White LED).
Make sure AC power cord is securely connected to the AC socket.
Plug another electrical device (such as a radio) to the power outlet to verify that the
outlet is supplying the proper voltage.
AUDIO Interconnection Issues
•
Remember that S-Video and Composite (AV) share the same audio source.
Power is ON but No Screen Image
•
•
•
•
Make sure the video cable connected to the HD Monitor is tightly secured to the
video output port on the back of the computer. If the other end of the video cable
is not attached properly to the HD Monitor, secure it tightly.
Adjust brightness and contrast.
If you are using a Macintosh computer older than G3, you need a Macintosh
adapter.
Check Source settings.
Wrong or Abnormal Colors
•
•
If any colors (red, green, or blue) are missing, check the video cable to make sure it
is connected securely. Loose or broken pins in the cable connector could cause an
improper connection.
Connect the HD Monitor to another computer.
Remote Control Buttons Do Not Work
•
Press only one button at a time.
No Sound
•
•
•
•
•
Check the audio connection.
Press MUTE on the remote control, so that MUTE disappears from the screen.
Check the audio settings. The HD Monitor audio may be set to minimum.
Press the Volume + (Up) key on the remote control.
Make sure the speaker setting is set to “internal”.
Remote Control Does Not Work
•
•
Make sure batteries are inserted correctly.
Replace batteries with new ones if necessary.
Remote Control Code Not Found in a “Universal” Remote
•
Purchase a separate “learning” remote control or log on to:
www.westinghousedigital.com for updated remote code info.
How Can I Find More Help?
•
•
Log on to: www.westinghousedigital.com
Contact Westinghouse Customer Service at (866) 287-5555 or write us at
service@westinghousedigital.com
21
English
•
•
•
USER’S MANUAL
MANUEL DE L’UTILISATEUR
MANUAL DEL USUARIO
LVM-42w2
HD Video Monitor
Moniteur Vidéo HD
Monitor de Video de Alta Definición
www.westinghousedigital.com
Westinghouse Digital Electronics
Santa Fe Springs, CA
SE-UM-4202-0501